So I was trying to update my old energy ROM to ICS and I'm kind of hosed. Got instructions here: http://forum.xda-developers.com/showthread.php?t=1362759
Basically:
- Root your device
- Install a custom recovery
- Install the downloaded ROM .zip found in post #3
- Make sure to do a Factory Reset / Wipe before installing ROM
For the record, these steps are out of order. Steps 4 and 3 are switched and I didn't notice till it was to late. What I did next was do the factory reset and then try to re-install the ROM. Everything seemed to go fine until it was time for a reboot. Then it froze on the HTC logo.
Could use some ideas as to what my next move should be. Since it was a previous version of Energy ROM + Faux kernel, phone is definitely rooted, etc. Perhaps I should start over with a stock Gingerbread ROM?
jcllings said:
So I was trying to update my old energy ROM to ICS and I'm kind of hosed. Got instructions here:
...
Perhaps I should start over with a stock Gingerbread ROM?
Click to expand...
Click to collapse
Apparently I am also supposed to flash the kernel as per this thread which I've finally found:
http://forum.xda-developers.com/showthread.php?t=1645641
In order to find it, I had to search for it using Google as this forum software is so haphazard. Also not mentioned in the instructions. Will try this next if I can get at it through just the custom recovery.
Still wrong. Coming from GB and going to ICS you need to flash the ICS RUU in bootloader. I don't know how many times its been mentioned or how many other threads have been started because of this issue.
--------------------------------
It's Better To Fail At Originality
Than To Succeed In Imitation.
--------------------------------
First im not resbonsible for anything that can happen to your phone this what i do if it didnt work im not resbonsible.
If you are rooted via HTCDev S-On Hboot 1.490018 and up you need to Run a command prompt and flash the boot.IMG that comes with the ROM (if not included extract the ROM and search for its in the .Zip file then move that file into a folder in the Root lf ur C Drive put your phone into fastboot mode (remove battery then put it back then press lock/on button and the volume up button at the same time) then connect it to your PC and run command prompt press on start and search for cmd then run it and type the following :
Cd c:\android (or whatever you named the folder)
After that type:
Fastboot flash boot boot.IMG
After its done unplug your phone from ur PC reboot it and it should work perfectly (it may stay at the HTC Logo for 10-20 minutes)
HOPE IT WORKS ENJOY!
Sent from my GT-P7500 using XDA Premium HD app
Double0EK said:
Still wrong. Coming from GB and going to ICS you need to flash the ICS RUU in bootloader.
...
--------------------------------
It's Better To Fail At Originality
Than To Succeed In Imitation.
--------------------------------
Click to expand...
Click to collapse
Awesome. Thanks for the tip. Will see what I can make of it.
I notice that there is a file, PH85IMG.zip in the same directory as the modded ROM. The name isn't very descriptive. Clue?
jcllings said:
So I was trying to update my old energy ROM to ICS and I'm kind of hosed. Got instructions here: http://forum.xda-developers.com/showthread.php?t=1362759
Basically:
- Root your device
- Install a custom recovery
- Install the downloaded ROM .zip found in post #3
- Make sure to do a Factory Reset / Wipe before installing ROM
For the record, these steps are out of order. Steps 4 and 3 are switched and I didn't notice till it was to late. What I did next was do the factory reset and then try to re-install the ROM. Everything seemed to go fine until it was time for a reboot. Then it froze on the HTC logo.
Could use some ideas as to what my next move should be. Since it was a previous version of Energy ROM + Faux kernel, phone is definitely rooted, etc. Perhaps I should start over with a stock Gingerbread ROM?
Click to expand...
Click to collapse
I don't want to put down energy rom, but it hasn't been updated since the original leak, and the instructions were never clarified - he simply never explained the PROPER way to switch from gingerbread to ICS. ARHD gives a better explanation, but I think post #2 in the everything ICS thread gives the best and links to everything you should need..
You have to be careful anytime you are switching to a totally new OS. All the devices I know, switching from 2.1 to 2.2, or 2.2 to 2.3.. or to 4.0+.. it is USUALLY not just a "flash over the old OS".. just something to keep in mind for any of your other or future devices..
yuseiatlas said:
First im not resbonsible for anything that can happen to your phone this what i do if it didnt work im not resbonsible.
...
After its done unplug your phone from ur PC reboot it and it should work perfectly (it may stay at the HTC Logo for 10-20 minutes)
HOPE IT WORKS ENJOY!
Sent from my GT-P7500 using XDA Premium HD app
Click to expand...
Click to collapse
I'm trying to get RUU now. When I tried the above earlier, got as far as the wirly Energy rings though but then it restarts.
Silentbtdeadly said:
I don't want to put down energy rom, but it ...
other or future devices..
Click to expand...
Click to collapse
Well as far as I know, it ain't like he is getting paid much so it would seem to be a miracle if any of this stuff gets updated. ;-) If I don't have this figured out by Tuesday, I'll use it as an excuse to get a new phone. This one has a crack or two in the screen anyways.
Still, even so I would MUCH rather get this one working again. 'specially since I'm between software gigs & cash is tight. If Energy ROM hasn't been updated and there's a better and/or more complete set of instructions maybe I should be looking at something else. Will continue hunting through these forums for info but can use all the help I can get since this forum software ain't exactly friendly. Probably best to see if I can get it back to stock on ICS and then work forward from there. Having said that, I have an RUU that I am working with, its: PH85IMG_RUBY_ICS_35_S_TMOUS_2.14.531.3_Radio_1.14.550L.17DC_30.78.550L.15_release_259626_signed.zip
Tried just flashing it but apparently there's more to it than that.
Latest problem is that I can't get it re-locked without enabling USB debugging. Can't do this since I don't have a working OS. Can it be done from CLI or recovery?
Uh.... hmmm... mysterious. Seems to have fixed itself. Will try a restart and see what happens.
jcllings said:
Latest problem is that I can't get it re-locked without enabling USB debugging. Can't do this since I don't have a working OS. Can it be done from CLI or recovery?
Uh.... hmmm... mysterious. Seems to have fixed itself. Will try a restart and see what happens.
Click to expand...
Click to collapse
I was saying that there are some other options, other roms, that have better instructions and have been updated fairly well.. that is all.
The thread I was talking about by glacierguy is here - it links to tons of resources and should answer most questions you may come up with. For example it has "Relock phone (fastboot oem lock)" you can issue fastboot commands while your phone is booted into the bootloader - so this has nothing to do with usb debugging..
There is tons of information here, I know it isn't absolutely organized, but there are a lot of guys here who tried to make the information as easy to find as possible..
Did u try to restart it again it usually takes a couple of times but anyway should either return to stock or use the RUU for the ICS ROM
Sent from my GT-P7500 using XDA Premium HD app
jcllings said:
Well as far as I know, it ain't like he is getting paid much so it would seem to be a miracle if any of this stuff gets updated. ;-) If I don't have this figured out by Tuesday, I'll use it as an excuse to get a new phone. This one has a crack or two in the screen anyways.
Still, even so I would MUCH rather get this one working again. 'specially since I'm between software gigs & cash is tight. If Energy ROM hasn't been updated and there's a better and/or more complete set of instructions maybe I should be looking at something else. Will continue hunting through these forums for info but can use all the help I can get since this forum software ain't exactly friendly. Probably best to see if I can get it back to stock on ICS and then work forward from there. Having said that, I have an RUU that I am working with, its: PH85IMG_RUBY_ICS_35_S_TMOUS_2.14.531.3_Radio_1.14.550L.17DC_30.78.550L.15_release_259626_signed.zip
Tried just flashing it but apparently there's more to it than that.
Click to expand...
Click to collapse
If you're.gonna flash that last file you mentioned, you need to rename it to PH85IMG, since its a stock ruu and not just a flashable Rom.
Sent from an Amaaaaaazing place :-D
Woohoo! I've succeeded in getting the aforementioned RUU installed. Should be much less of a problem from here forward.
yuseiatlas said:
First im not resbonsible for anything that can
...
Sent from my GT-P7500 using XDA Premium HD app
Click to expand...
Click to collapse
Of course you are responsible. Heaven forbid anyone should take responsibility for their own actions or anything crazy like that.
Since English may not be your first language, I'll be clear. I'm just kidding.
Silentbtdeadly said:
I don't want to put down energy rom, but it hasn't been updated since the original leak, and the instructions were never ...
other or future devices..
Click to expand...
Click to collapse
Now that I have the RUU, could use some examples of projects that are more up-to-date so that I can move forward.
jcllings said:
Now that I have the RUU, could use some examples of projects that are more up-to-date so that I can move forward.
Click to expand...
Click to collapse
Whoops, you covered this earlier. Will chase down the link and see where it goes.
jcllings said:
Now that I have the RUU, could use some examples of projects that are more up-to-date so that I can move forward.
Click to expand...
Click to collapse
If you want cutting edge(these both have features no other rom has added yet, and are very current update wise) and like the senseui, try remix's http://forum.xda-developers.com/showthread.php?t=1673609 or if you want with less sense and more of an aosp-ish feel go for his http://forum.xda-developers.com/showthread.php?t=1623184
ARHD is what is being used for the base for many roms because it is solid and bugless, energy has more features that he had included in his gingerbread rom.. I've heard good things about capromce, but I have no idea what features he has added that are or aren't included in the others..
Heheheh and its not my first language thats why you might see a lot of grammar and/or writen mistakes, just for the futur before you flash any new ROM Back-Up you current or the original ROM just in case something like this happen so you can restsore it without worrying and hope i helped
Sent from my GT-P7500 using XDA Premium HD app
Righteous! Up and running on Speed ROM 4.0. Thanks so much to everyone who collaborated. Copious mashing of the Thanks button.
Related
Go easy on me guys I tried looking for the answers for the last 3-4 hours. ;/
I already rooted my phone using this guide
http://forum.xda-developers.com/showthread.php?t=1310115
and unlocked the bootloaded as well using the htcdev website.
And I would like to install beastmod. I went through the faq and the whole bit but still have questions and still a tad bit confused. I even went online to google and search the forum.
I know this is the official thread for beast mod
http://forum.xda-developers.com/showthread.php?t=1313017?referrerid=922386
I have unlocked the boot loader, do I need to flash the kernel still? This is where I am confuse.
I read the
"FAQ for the HTC Amaze 4G. Read Frequently Asked Questions before you post a question!"
and
"HTC AMAZE ROM Bible - Everything you need to know"
I'm coming from a Blackberry which I used for almost 6 years.
I'm just kinda stumped right now as far as steps I need to take if any prior to installing Beastmod. I have never installed a rom before but I figure I ask the questions above before attempting anything.
Forgive me if i'm wrong everyone, but i think the Kernel is already cooked into the ROM. So no need for flashing a kernel after flashing the ROM.
I too am new to the HTC Amaze. I'm coming from a Samsung Galaxy S2 and was also running BeastMod v4.0. And God is this a pain in the butt to root. Last HTC phone i had was a HTC TouchPro. WinMo6 ftl
Really? What made you go to the Amaze? I came in T Mobile store thinking I was going to walk out with the S2 but after 3 days I ended up leaving with the Amaze, just seemed like a better phone.
Have you installed beastmod on your phone going?
Oh i still have my SGS2, just got really bored with it dev wise. Too many Roms with pretty much the same things. BeastMod was really the only ROM that stood out. Just got my Amaze last night, so i haven't even been able to try to root it yet. I've been reading alot of tutorials, and it sounds fairly easy....just alot of steps than what i'm used to. But so far, i'm really liking the Amaze over the SGS2. Sense and the camera are a WIN!
As far as I can tell from reading the official BeastMod first post you do need to flash the kernel.
That message below is right in the change log.
"**FULL WIPE REQUIRED FOR v2.2.0 and Kernel Flash**
YES!
You must flash the Kernal with Kernal Flasher
We do not have S-off... Security Off
So Kernals can not be buried in the rom they have to be seperate. We do not anticipate S-off any time soon. Since bootoader is unlocked we can use ADB to push the kernal. VIOLA! for us mere mortals the mighty DEV have created a tool that does it for us!
I just want to help. I find it hard to believe you did not see this in like every Xboarder ROM thread there is! Follow instructions on front page of the ROMs. They are explicit.
Feel free to PM if you have issues though. Amaze is my first Android phone and I cut my teeth with it so I should be a good resource. Cheers
I still do not see that thread, I just looked. I;ve spent a few hours on this but still determined to do it.
nguyendqh said:
As far as I can tell from reading the official BeastMod first post you do need to flash the kernel.
That message below is right in the change log.
"**FULL WIPE REQUIRED FOR v2.2.0 and Kernel Flash**
Click to expand...
Click to collapse
Now thats really confusing. But i guess we'd have to go with what the latest changelog says.
babymatteo said:
Now thats really confusing. But i guess we'd have to go with what the latest changelog says.
Click to expand...
Click to collapse
How do you think I feel?
Alright so fact, need to flash kernel 1st.
Alright I found this
http://forum.xda-developers.com/showthread.php?t=1328141
Which I assume its the correct one.
I am confused at number 4,
4. Place the boot.img that you want to be flashed in the Kernel-Here folder.
Which boot.img? The one thats included in beastmod?
and 5
5. Make sure adb is enabled on your phone via settings
adb?
You always flash the ROM first then the Kernel.
babymatteo said:
You always flash the ROM first then the Kernel.
Click to expand...
Click to collapse
I don't know what you mean by that could you be more specific please?
Do you see on the BeastMod thread where you downloaded the ROM?
Underneath it, it says "Kernel for 2.2.0" that is the boot.img download it.
As for ADB under settings this is just referring to "USB debugging" turned on.
Put the boot.img in the "Kernel Here" folder which is in the "Kernal Flash Tool v3".
Then after run the flash.bat (windows) or flash.sh(mac) file in that tool folder.
That should do it.
---------- Post added at 05:54 PM ---------- Previous post was at 05:53 PM ----------
F9zSlavik said:
I don't know what you mean by that could you be more specific please?
Click to expand...
Click to collapse
And where are you still having problems?
That's what I thought but I wanted to make sure that what I needed to do, I was semi sure but I do not want to brick my phone by doing a step I was not suppose to.
ADB is a confusing term debugging makes a lot more sense and that is what I figured but I did not see any reference between adb and debugging mode.
So after following these steps, this will install beastmod?
I saved my contacts, sms, and call logs using a program called supa back up, they were saved on my sd card.
Anything else I need to know?
And thank yo for taking the time to fill in the gaps I really do appreciate and hopefully this thread will help anyone else that was confused as I was.
UPDATE
Does the phone need to be in any specific mode? I have it as Disk Drive and after running the bat I get a msg saying error device not found" and "waiting for device"
F9zSlavik said:
That's what I thought but I wanted to make sure that what I needed to do, I was semi sure but I do not want to brick my phone by doing a step I was not suppose to.
ADB is a confusing term debugging makes a lot more sense and that is what I figured but I did not see any reference between adb and debugging mode.
So after following these steps, this will install beastmod?
I saved my contacts, sms, and call logs using a program called supa back up, they were saved on my sd card.
Anything else I need to know?
And thank yo for taking the time to fill in the gaps I really do appreciate and hopefully this thread will help anyone else that was confused as I was.
UPDATE
Does the phone need to be in any specific mode? I have it as Disk Drive and after running the bat I get a msg saying error device not found" and "waiting for device"
Click to expand...
Click to collapse
The boot.img is the kernel. Flashing it doesn't mean you have BeastMod.
You need to download BeastMod and flash it through recovery to get BeastMod on your phone.
Remember to wipe data, wipe dalvik and wipe cache.
After you flash the ROM then you flash the kernel using the tool.
Sometimes the kernel needs to flashed twice to fix any issues you might have after flashing a ROM and new kernel.
First boot takes longer and after first boot, once the phone settles, reboot again.
Your phone needs to be in "charge only" and not "disk drive" for ADB to recognize it.
do not worry about bricking your phone, you actually cant since there is no s-off yet + htc hasnt released much of the sources so pretty much ur phone is locked and cant brick it.
OK I did the flash.bat, phone restarted.
So in order to install the beastmod, do I copy the beastmod file I downloaded into the sdcard? Then reboot and install it through recover?
How do I wipe the data?
F9zSlavik said:
OK I did the flash.bat, phone restarted.
So in order to install the beastmod, do I copy the beastmod file I downloaded into the sdcard? Then reboot and install it through recover?
How do I wipe the data?
Click to expand...
Click to collapse
Yes. Copy the zip you downloaded on to your sdcard then reboot into recovery.
Volume down + power.
Once in recovery you should have options.
First do a backup.
Then look for the options to wipe data/factory reset.
Then usually wipe cache and wipe dalvik are under the "advanced" option.
I do believe you have a custom recovery so your options might be different.
Navigate around to find the options to wipe all your data.
After you wipe then you navigate to "apply update from sdcard" and then "choose zip from sdcard" select BeastMod and flash it.
You should be ready to go.
Sorry my instructions aren't specific as I haven't rooted my Amaze or flashed a custom ROM.
So I don't know what your recovery looks like.
I am going off my experience with 7 MT4Gs and 2 Sensations.
The steps should be pretty basic when flashing a ROM anyway.
I understand that for someone who is new at this reading the instructions might seem complicated at times.
I'm just trying my best to reword those instructions for you and put it steps you can understand.
Alright, final question, do I need to make a folder for the files that in the zip folder or do I just copy them to the sdcard2 directory as the way its shown when you un zip the beastmod.zip file?
F9zSlavik said:
Alright, final question, do I need to make a folder for the files that in the zip folder or do I just copy them to the sdcard2 directory as the way its shown when you un zip the beastmod.zip file?
Click to expand...
Click to collapse
Don't unzip it. Just place the entire thing on your sdcard.
If you're flashing the ROM through recovery you should not need to unzip it.
It's just placing it on your SDcard and flashing it.
ooooh
I will try it right now then.
OK
Off topic question, Cynogen is a mod like Beastmod correct?
UPDATE
Alright its been flashed yay it works lol. Do I need to flash the kernel again? I did it before, do i have to do it afterwards as well, you mention that earlier.
Boy it looks so different...... so the Sense theme is still there but just hidden in some sort of way? Will they ever disable the security on this phone or is that permanent?
Dude if the admin are smart they will PIN this thread. I am a computer guy I fix them for a living mod the etc and damm this was a pain in the ass. The information is there but its missing certain details and its scattered, I searched around and sort of has the jist of it but honestly they should make a faq on how to more or less how its detailed in this thread, would save a lot of time and effort.
This forum is so awesome! lol
This is going to need some getting use to....
Any advice on what to do next? lol Like I said this is the 1st time I've own a phone that is not a blackberry...
Was running NRG GB just fine. When giving the phone to the wife I decided to upgrade to ICS. Used CWM to wipe data, cache, etc, and installed, got freeze on HTC logo. Started using Superwipe before each try and also tried flashing several different kernels including the one inside the zip and the one included with the amaze stock kernel flasher. Now the best I can get is 5 seconds into the Energy spinning rings logo before a 5s freeze and reboot.
The only thing I haven't tried is firmware; I've seen references to "find it on the forums" but copious forum and google searches don't seem to lead to the ICS firmware itself. Can anyone help with that or point out what I'm forgetting?
In the meantime I will try installing the ICS stock ROM first and see where that gets me.
ten6 said:
Was running NRG GB just fine. When giving the phone to the wife I decided to upgrade to ICS. Used CWM to wipe data, cache, etc, and installed, got freeze on HTC logo. Started using Superwipe before each try and also tried flashing several different kernels including the one inside the zip and the one included with the amaze stock kernel flasher. Now the best I can get is 5 seconds into the Energy spinning rings logo before a 5s freeze and reboot.
The only thing I haven't tried is firmware; I've seen references to "find it on the forums" but copious forum and google searches don't seem to lead to the ICS firmware itself. Can anyone help with that or point out what I'm forgetting?
In the meantime I will try installing the ICS stock ROM first and see where that gets me.
Click to expand...
Click to collapse
Do just that, remember to lock your bootloader if you're s-on and yes, jumping to an ICS rom without updating your device caused the bootloop.
Dark Nightmare said:
Do just that, remember to lock your bootloader if you're s-on and yes, jumping to an ICS rom without updating your device caused the bootloop.
Click to expand...
Click to collapse
Thanks for the reply! I'm downloading PH85IMG_RUBY_ICS_35_S_TMOUS_2.14.531.3_Radio_1.14.550L.17DC_30.78.550L.15_release_259626_signed.zip from filefactory, it's taking forever. Am I flashing this with CWM? Or should I be downloading a GB factory ROM and using that instead, then re-locking the bootloader and trying to update over the air?
ten6 said:
Thanks for the reply! I'm downloading PH85IMG_RUBY_ICS_35_S_TMOUS_2.14.531.3_Radio_1.14.550L.17DC_30.78.550L.15_release_259626_signed.zip from filefactory, it's taking forever. Am I flashing this with CWM? Or should I be downloading a GB factory ROM and using that instead, then re-locking the bootloader and trying to update over the air?
Click to expand...
Click to collapse
Don't download that one, it has issues, hold up, I'll give you a link to the most recent file.
Here, get this: http://d-h.st/3VD
Download speed should be faster as well. rename it PH85IMG and place it on your sd card after you relock your bootloader, then boot into bootloader, it's gonna detect the file and ask you if you wanna update, follow the on screen instructions to update, voila! Follow the basics to install the new energy rom.
It's almost as tho NO One reads anymore. It's actually getting kinda ridiculous how many times the same issue is gonna be asked.
I know this post isn't very helpful but I'm sure most of the recognized/senior/not noobs members are getting frustrated.
~~~~~~~~~~~~~~~~~~~~~~~~
It's Better To Fail At Originality
Than To Succeed In Imitation.
-Mighty Healthy
Click to expand...
Click to collapse
Double0EK said:
It's almost as tho NO One reads anymore. It's actually getting kinda ridiculous how many times the same issue is gonna be asked.
I know this post isn't very helpful but I'm sure most of the recognized/senior/not noobs members are getting frustrated.
~~~~~~~~~~~~~~~~~~~~~~~~
Click to expand...
Click to collapse
It is useful, I fully agree with you, it's like we come here to answer the same questions over and over, but I'm just trying to be nice, cause I usually just say, read the amaze bible, but then they go and do something even more noobish, so to avoid the tear jerks I just give the basic info, though I'm fading away slowly.
Thanks'd for the link and the help. I was gonna get mad about being called a noob who can't read, but I guess it's a small price to pay for instant, free help. Keep on rockin' XDA.
I came across this issue. As earlier posts said, install the new ICS update. The partitions were messed up and the ruu will clean it up.
ten6 said:
Thanks'd for the link and the help. I was gonna get mad about being called a noob who can't read, but I guess it's a small price to pay for instant, free help. Keep on rockin' XDA.
Click to expand...
Click to collapse
Lol, never pointed fingers buddy, so calm down.
Maybe I should create a new topic but my issue is similar to this one except for the fact that I read quite a lot and tried quite a few things.
My situation is that I made a backup with cwm only booted not flashed so I have the 100% stock backed up, after this I flashed cwm and tried to install the Energy rom based on ics and that was my mistake as I used to be on a Nexus device I didn't have to worry about this.
So I got stuck on a bootloop and tried factory reset/wiping everything, tried to reinstall a stock ROM (t-mobile one as I only found a .exe for the videotron one and I did not feel like exploring the exe as I am a Linux user) by relocking bootloader and using the HTC method, tried to install manually the stock Kernel with Energy ROM using adb and fastboot commands, tried to restore my backup but nothing seems to work, I'm still bootlooping.
Is-it possible to s-off without a regular adb access (only the cwm adb access)? And would s-off allow me to flash anything as I wish? Is there a way to have any ROM working on my device? (i know the answer is yes to the last one, at least )
Thanks!
Edited: I don't know why I even replied to the post above this.
Read more you'll find out what you're doing wrong.
~~~~~~~~~~~~~~~~~~~~~~~~
It's Better To Fail At Originality
Than To Succeed In Imitation.
-Mighty Healthy
Click to expand...
Click to collapse
Double0EK said:
Edited: I don't know why I even replied to the post above this.
Read more you'll find out what you're doing wrong.
~~~~~~~~~~~~~~~~~~~~~~~~
Click to expand...
Click to collapse
Maybe I'm a noob on this forum but it's far to be the first time I face a problem in software configuration/installation and I read quite enough (spent about five hours on xda, google, etc.) to say that you should at least help me a bit by linking me to a thread where I can find an answer.
I know my mistake was to install ics at first but now I flashed the stock recovery back, I relocked the bootloader via fastboot and put the file on the root of my sdcard renamed correctly that it be detected automaticly (and it apparently does install) but I still got the * bootloop.
I'm able to read a manual and to read the Amaze 4G bible four times to try to point out the detail I forgot. I made my homework and now it would only be nice from you that you help me a bit...
johnride said:
Maybe I'm a noob on this forum but it's far to be the first time I face a problem in software configuration/installation and I read quite enough (spent about five hours on xda, google, etc.) to say that you should at least help me a bit by linking me to a thread where I can find an answer.
I know my mistake was to install ics at first but now I flashed the stock recovery back, I relocked the bootloader via fastboot and put the file on the root of my sdcard renamed correctly that it be detected automaticly (and it apparently does install) but I still got the * bootloop.
I'm able to read a manual and to read the Amaze 4G bible four times to try to point out the detail I forgot. I made my homework and now it would only be nice from you that you help me a bit...
Click to expand...
Click to collapse
Okay okay, calm down, there's currently only one method of going about restoring your device since you're s-on and no you cannot s-off with just cwm adb, I think JB s-off method is only an exe file, never saw linux files anywhere on his site. Anyways, you have to use the GB exe for videotron and restore to stock via it then update to ics to use the most recent energy rom, BUT if you just want a working device, this is just an idea, though it should work fine, you can flash a custom recovery and flash the GB version of energy rom, you should be able to restore your backup as well, but you said you can't, which is odd, it may be because of the kernel not being flashable as since CWM cannot flash kernels while s-on, in which case I'd advise you to get 4EXT recovery and then try restoring your back once again, it should work fine since 4EXT can flash kernels while S-ON.
My two cents.
Well, 4ext doesn't works, apparently it flashes correctly but I can't boot in it so can't even try to restore my backup, s-off doesn't works from cwm and my device has to be booted to work with Videotron's exe (or I badly installed my drivers, I nerver understand properly the 899363 drivers per device I have to install for an android phone on Windows?)
Smells bad... I checked the 4ext's md5sum and it's alright, I took it from the fastboot installable img in direct dl from the thread in the Amaze bible.
Any idea?
Oh and there is a JB s-off executable for Linux on his site. After all I guess it is mostly adb commands?
johnride said:
Well, 4ext doesn't works, apparently it flashes correctly but I can't boot in it so can't even try to restore my backup, s-off doesn't works from cwm and my device has to be booted to work with Videotron's exe (or I badly installed my drivers, I nerver understand properly the 899363 drivers per device I have to install for an android phone on Windows?)
Smells bad... I checked the 4ext's md5sum and it's alright, I took it from the fastboot installable img in direct dl from the thread in the Amaze bible.
Any idea?
Oh and there is a JB s-off executable for Linux on his site. After all I guess it is mostly adb commands?
Click to expand...
Click to collapse
I got lost halfway through that post, after flashing a rom, if the kernel isn't flashed (reboots and does it automatically), then flash the kernel manually, should boot fine, does anyone ever really read anymore? This very issue both s-on and s-off has been answered more times today than I can count. If you read the details on JB's site, you'd see and know all you need to.
Right, I'va already flashed manually the stock kernel as sais in the NRGRom thread without success before my first post here, will look at different kernels.
johnride said:
Right, I'va already flashed manually the stock kernel as sais in the NRGRom thread without success before my first post here, will look at different kernels.
Click to expand...
Click to collapse
How did you go about flashing the kernel?
Sent from my SGH-T679 using xda app-developers app
There was a flash.sh file in the zip with the kernel, I couldn't run it normally as I can't boot but I went in cwm (maybe I should have used 4ext, don't think so for this part) executed the adb commands there were in the sh file with all filesystems mounted, rebooted into fastboot and flashed the kernel image. Maybe there are differents /system when in cwm and when booted on regular system... Will figure that out when I have time to spend on this, as soon as possible.
Thanks for all the cues!
Sent from my Nexus S
johnride said:
There was a flash.sh file in the zip with the kernel, I couldn't run it normally as I can't boot but I went in cwm (maybe I should have used 4ext, don't think so for this part) executed the adb commands there were in the sh file with all filesystems mounted, rebooted into fastboot and flashed the kernel image. Maybe there are differents /system when in cwm and when booted on regular system... Will figure that out when I have time to spend on this, as soon as possible.
Thanks for all the cues!
Sent from my Nexus S
Click to expand...
Click to collapse
Okay here's a few tips, cwm cannot flash kernels with son devices, get 4ext recovery for that. Second thing, reflash the from after doing a super wipe, if 4ext doesnt reboot and flash the kernel, do it manually, ill assume you know how to use ad, if not check my Bible tutorial on it, use the boot command for flashing boot images, take the boot file from the zip file, place it in the folder where your adb files are and flash it to your device while its in fastboot mode.
Sent from my SGH-T679 using xda app-developers app
Well, I think I have done all you mention above, the only thing i'm not sure to understand is what you mean by "super wipe" I found some executables about it but I guess it can't do much more than the flash all partitions (except external sdcard) in 4ext recovery wich I finally managed to install properly.
So, I made that global formatting thing, I tried to install an ICS based ROM and 4ext rebooted to install kernel, same bootloop. Tried to install manually the kernel that came with this rom via the classic fastboot flash boot boot.img. Same bootloop. Tried to put the modules manually via the recovery adb access (performing a mount -a in adb shell to have everything present in fstab mounted) and flashing this stock kernel with no more success.
Achieved the same operations with a GB based ROM (this one: http://forum.xda-developers.com/showthread.php?t=1535173) with both the faux and the stock kernel without any more success.
Did I miss something? Am I so dumb? Do you have any other rom to suggest that have higher chances to succeed?
Do you think trying to restore my sotck nandroid with 4ext has more chances to succeed?
Thanks, again and always!
I just rooted my phone, installed 2 different kernels, my phone's wifi now only 'Error's I factory restored (flash recovery with stock Evo info.)
Honestly I feel really stupid. I can't even flash my TWRP back on. Any advice or help would be greatly appreciated. I am fairly new to Rooting and its customizations. Thank you.
xFatex said:
I just rooted my phone, installed 2 different kernels, my phone's wifi now only 'Error's I factory restored (flash recovery with stock Evo info.)
Honestly I feel really stupid. I can't even flash my TWRP back on. Any advice or help would be greatly appreciated. I am fairly new to Rooting and its customizations. Thank you.
Click to expand...
Click to collapse
Can you access your recovery
Sent from my EVO using XDA Premium 4 mobile app
It might also help to post what ROM you were running, along with what two kernels you flashed. Certain kernels only work with certain ROM's (AOSP kernels don't work on Sense ROM's, and vice-versa). Take a look at the top link in my sig. At the bottom is a few helpful links. om4 has an excellent "Don't Panic" guide that contains some excellent info and really should be required reading for new users.
Sent from my HTC EVO 4G LTE
lreyes said:
Can you access your recovery
Sent from my EVO using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I had no access to my TWRP Recovery, I actually fixed that though.
The Kernel is changed and now I have no Data access? I think my ROM is not compatible like suggested. (Sense ROM)
FinZ28 said:
It might also help to post what ROM you were running, along with what two kernels you flashed. Certain kernels only work with certain ROM's (AOSP kernels don't work on Sense ROM's, and vice-versa). Take a look at the top link in my sig. At the bottom is a few helpful links. om4 has an excellent "Don't Panic" guide that contains some excellent info and really should be required reading for new users.
Sent from my HTC EVO 4G LTE
Click to expand...
Click to collapse
The current situations has changed sadly.
I have no custom ROM just Sense.
The Kernel: Bulletproof-EVO-v1.4.
ROM: Default Sense?
This is my first attempt at really rooting/adding kernels just messing around and doing damage.
Now instead of WiFi I have no Data Service with this Kernel and ROM combo. I will check out your links thank you very much.
FinZ28 said:
It might also help to post what ROM you were running, along with what two kernels you flashed. Certain kernels only work with certain ROM's (AOSP kernels don't work on Sense ROM's, and vice-versa). Take a look at the top link in my sig. At the bottom is a few helpful links. om4 has an excellent "Don't Panic" guide that contains some excellent info and really should be required reading for new users.
Sent from my HTC EVO 4G LTE
Click to expand...
Click to collapse
Now my phone is stuck in bootloop I even tried to remove TWRP recovery to to StockRecovery...
Just let it die?
Or is there anyway to flash a Kernel via command prompt?
Anyway to fix this?
xFatex said:
Now my phone is stuck in bootloop I even tried to remove TWRP recovery to to StockRecovery...
Just let it die?
Or is there anyway to flash a Kernel via command prompt?
Anyway to fix this?
Click to expand...
Click to collapse
Hit the top link in my sig. I think you'll find what you're looking for there. Sounds like you may need to reflash your recovery from the bootloader via fastboot. Assuming that works, you need to due a full system wipe from recovery, then flash a ROM.
Sent from my HTC EVO 4G LTE
FinZ28 said:
Hit the top link in my sig. I think you'll find what you're looking for there. Sounds like you may need to reflash your recovery from the bootloader via fastboot. Assuming that works, you need to due a full system wipe from recovery, then flash a ROM.
Sent from my HTC EVO 4G LTE
Click to expand...
Click to collapse
Do forgive me, I am reading your thread and advice.
I am just running on zero sleep in the past 4 days and trying to fix this all day.
The bootloop is gone now that I have flashed the TWRP recovery Stock recovery and Twrp again.
The stock recovery was still giving me the twrp startup screen (disclaimer at the HTC screen)
I also don't quite get what to do via Hboot 2.09 (what I have)
All the ROM's with the kernels are in a zip that needs to be opened via TWRP well the ones I download...
I have wiped the ceche/delvik etc... fear I wiped the whole thing by accident rendering the device empty.
My android's exe file doesn't seem to be about either.
Android version: 4.1.1
Software: 3.17.650? (The most recent for Evo commercially)
When I do attempt a Stock restore via fastboot flash not exe file I end up getting the red ! next to my phone and the phone doesn't reboot naturally.
Do I need to hunt down ROM's and Kernels that I can flash into the cmd?
I understand with my version I must flash in the using the prompt and have them separate but I am totally new at this I feel really dumb I'm sorry if I am bothering you with redundant questions I am attempting to follow and get the information but I think I am reading so many different threads on it I am suffering from information overload (artist not a programmer lol.)
EDIT:
NOTE:
I AM currently reading your bottom link about Fixing system wipe.
xFatex said:
Do forgive me, I am reading your thread and advice.
I am just running on zero sleep in the past 4 days and trying to fix this all day.
The bootloop is gone now that I have flashed the TWRP recovery Stock recovery and Twrp again.
The stock recovery was still giving me the twrp startup screen (disclaimer at the HTC screen)
I also don't quite get what to do via Hboot 2.09 (what I have)
All the ROM's with the kernels are in a zip that needs to be opened via TWRP well the ones I download...
I have wiped the ceche/delvik etc... fear I wiped the whole thing by accident rendering the device empty.
My android's exe file doesn't seem to be about either.
Android version: 4.1.1
Software: 3.17.650? (The most recent for Evo commercially)
When I do attempt a Stock restore via fastboot flash not exe file I end up getting the red ! next to my phone and the phone doesn't reboot naturally.
Do I need to hunt down ROM's and Kernels that I can flash into the cmd?
I understand with my version I must flash in the using the prompt and have them separate but I am totally new at this I feel really dumb I'm sorry if I am bothering you with redundant questions I am attempting to follow and get the information but I think I am reading so many different threads on it I am suffering from information overload (artist not a programmer lol.)
Click to expand...
Click to collapse
if youre S-OFF then you can just use ViperRUU and then reunlock your device.
lreyes said:
if youre S-OFF then you can just use ViperRUU and then reunlock your device.
Click to expand...
Click to collapse
S-ON.
I am attempting to download MeanBean after reading Fin's Fix.
Though I don't know if FlashImage GUI will work.
I also have to figure out how to flash .apk files too...
Sorry about the bother... I really am far below Novice at this I should have had someone holding my hand step by step lol.
Okay, so the problem with the Kernel originally was it wasn't compatible?
Then the next one with the service error was I suppose the same thing?
Then when I tried to restore apparently I wiped my phone of all Data resulting in a bootloop and being no one has the exe file for the factory RUU of the latest version for the Evo 4g LTE I had no way of restoring any of the files?
So then I stalked Fin's suggestions eventually lead me to MeanBean. at least it got me up and running... I attempted to back up with TWRP.
Which apparently doesn't work (I have to learn how to backup else where... Lets add it to my list.)
But after I attempted the back up I also attempted the instillation of "Operation Jelly Bean" I love the ROM I love the theme I love the sleekness
Apparently I am missing something with my touch panel software. I wish I could have kept the ROM but couldn't sadly (If you know what I am doing wrong I would love to keep that ROM in the future)
So with another failed ROM I tried to restore... which there was no restore when I went to do so... I was a little frustrated from my constant bricking as is...
I attempted factory restore apparently also wiped everything (Internal sd, external, everything.) I don't know what is up with that do you have any clue if its a glitch or am I just wiping it?
I also do Stock restore that does absolutely nothing for my phone anymore...
I will flash it... and it does nothing... it still runs like TWRP (disclaimer etc) but won't go to the twrp boot screen... this is a bit frustrating.
Phone was working great until it just froze, I did a battery pull and now it won't go past the HTC white logo screen.
It boots into recovery, but only as safe mode.
Cannot access internal memory or external memory.
Haven't tried wiping the system since I can't really access the storage space to flash anything, or even restore a backup.
It's not dead. Simone else just posted the same exact problem.
Download the latest ruu. Pull your external sdcard.
Put sdcard in the computer.
Copy the ph85img.zip to it.
Put sdcard in phone.
Boot to bootloader.
Follow the on screen instructions.
That'll get you back to square one.
Also look for Odysseus' post in the other threads. He has some good information on this subject.
Sent from my HTC_Amaze_4G using xda app-developers app
chevycowboyusa said:
It's not dead. Simone else just posted the same exact problem.
Download the latest ruu. Pull your external sdcard.
Put sdcard in the computer.
Copy the ph85img.zip to it.
Put sdcard in phone.
Boot to bootloader.
Follow the on screen instructions.
That'll get you back to square one.
Also look for Odysseus' post in the other threads. He has some good information on this subject.
Sent from my HTC_Amaze_4G using xda app-developers app
Click to expand...
Click to collapse
Thank you for the advice. I was thinking about putting the ruu but I wasn't sure. I needed confirmation on this issue.
I will keep you posted about what happens.
Darin_Ram said:
Thank you for the advice. I was thinking about putting the ruu but I wasn't sure. I needed confirmation on this issue.
I will keep you posted about what happens.
Click to expand...
Click to collapse
As Chevy said, someone else posted with this exact same problem a day or two ago. Since you're S-off and unlocked the procedure is to download the latest factory image for your device. You can't flash one from another carrier or you'll brick it. There are links in one of the "pinned" threads at the top of the forums.
Once you have it downloaded rename it to "PH85IMG.zip" (note the capitalization must be exactly the same) and place it in the root of your external SD card. Now comes the fun part. It won't flash on an unlocked bootloader, so you must relock it using ADB commands or with the Amaze toolkit (don't worry you won't loose S-off). BTW I hope you saved the HTC unlock blob from when you first unlocked as you'll need it again to unlock later.
Flash the image from the bootloader hboot. When it's finished then go to settings / about phone /software information and accept any HTC updates. With a T-Mobile phone there will be at least three OTA's depending on which image you installed. Two of them are 30MB and require rebooting in between. The last one just updates a couple of .apks and doesn't need a reboot. You need these to get the latest radio.
Once all of the updating is finished you'll be back to factory with the latest radio. Now all you have to do is unlock, install a recovery, reroot, SuperCID, and you'll be ready to play again.
I hope this helps
Thanks again for the help, the phone is functional again. Does anybody have any idea why this happens?
Odysseus1962 said:
As Chevy said, someone else posted with this exact same problem a day or two ago. Since you're S-off and unlocked the procedure is to download the latest factory image for your device. You can't flash one from another carrier or you'll brick it. There are links in one of the "pinned" threads at the top of the forums.
Once you have it downloaded rename it to "PH85IMG.zip" (note the capitalization must be exactly the same) and place it in the root of your external SD card. Now comes the fun part. It won't flash on an unlocked bootloader, so you must relock it using ADB commands or with the Amaze toolkit (don't worry you won't loose S-off). BTW I hope you saved the HTC unlock blob from when you first unlocked as you'll need it again to unlock later.
Flash the image from the bootloader hboot. When it's finished then go to settings / about phone /software information and accept any HTC updates. With a T-Mobile phone there will be at least three OTA's depending on which image you installed. Two of them are 30MB and require rebooting in between. The last one just updates a couple of .apks and doesn't need a reboot. You need these to get the latest radio.
Once all of the updating is finished you'll be back to factory with the latest radio. Now all you have to do is unlock, install a recovery, reroot, SuperCID, and you'll be ready to play again.
I hope this helps
Click to expand...
Click to collapse
Holy crap I did none of the above. The ruu flashed on the unlocked bootloader, I didn't even capitalize it.
The bootloader stayed unlocked, I didn't check the supercid on it................................................................ I just re-installed the recovery
It booted fine though, so I have no idea what's going on
Darin_Ram said:
Thanks again for the help, the phone is functional again. Does anybody have any idea why this happens?
Click to expand...
Click to collapse
I'm as careful as they come. but it happened to me a few weeks back too. Sometimes you just get a bad flash, other times NAND memory cells get stuck (they wear out over time) or are slow to accept data. All it takes is an important part of the file system flashed onto a bad data block and the whole thing can get stuck in a loop. For me I had been trying out a bunch of ROMS and somehow a kernel failed to flash. I ended up with a kernel mismatch (kernel modules don't match the kernel) which resulted in a bootloop.
As a precaution I just keep an old 2GB SD-card handy that only has the Amaze image on it, so in case of an emergency all I have to do is relock the bootloader, stick in the SD card and I'm back in action within 15 mins.
Odysseus1962 said:
I'm as careful as they come. but it happened to me a few weeks back too. Sometimes you just get a bad flash, other times NAND memory cells get stuck (they wear out over time) or are slow to accept data. All it takes is an important part of the file system flashed onto a bad data block and the whole thing can get stuck in a loop. For me I had been trying out a bunch of ROMS and somehow a kernel failed to flash. I ended up with a kernel mismatch (kernel modules don't match the kernel) which resulted in a bootloop.
As a precaution I just keep an old 2GB SD-card handy that only has the Amaze image on it, so in case of an emergency all I have to do is relock the bootloader, stick in the SD card and I'm back in action within 15 mins.
Click to expand...
Click to collapse
That's a good idea, but is it really necessary for me right now? You know, since the bootloader is still unlocked, SuperCID is still 1's and I'm still S-OFF?
If it happens again, I'll re-lock, reload, and re-flash
Darin_Ram said:
Holy crap I did none of the above. The ruu flashed on the unlocked bootloader, I didn't even capitalize it.
The bootloader stayed unlocked, I didn't check the supercid on it................................................................ I just re-installed the recovery
It booted fine though, so I have no idea what's going on
Click to expand...
Click to collapse
Did you flash from your SD card or push the ruu with ADB? Usually it will only accept the zip image from the bootloader, but the ruu can be pushed with ADB.
What ever the case I'm just glad things worked out.
Odysseus1962 said:
Did you flash from your SD card or push the ruu with ADB? Usually it will only accept the zip image from the bootloader, but the ruu can be pushed with ADB.
What ever the case I'm just glad things worked out.
Click to expand...
Click to collapse
Flashed via SD card.
By the way, can we dual boot this phone?
I know, it's risky booting it to two os, but I'm just wondering cause making backups and restoring nandroids are becoming a pain every time I want to take good photos. :/ So I was wondering if we could dual boot.
I dual booted my old defy that only had about half the ram, and half the processing speed lmao so why not this device?
Darin_Ram said:
Flashed via SD card.
By the way, can we dual boot this phone?
I know, it's risky booting it to two os, but I'm just wondering cause making backups and restoring nandroids are becoming a pain every time I want to take good photos. :/ So I was wondering if we could dual boot.
I dual booted my old defy that only had about half the ram, and half the processing speed lmao so why not this device?
Click to expand...
Click to collapse
I could dual boot on my old HD2 as well. I don't believe any devs here have written a bootloader with that capability for the Amaze, but you could always just do a search and find out for yourself. It might be just a matter of porting an existing app to this device. Good luck!!!!
Odysseus1962 said:
I could dual boot on my old HD2 as well. I don't believe any devs here have written a bootloader with that capability for the Amaze, but you could always just do a search and find out for yourself. It might be just a matter of porting an existing app to this device. Good luck!!!!
Click to expand...
Click to collapse
I googled it, the only thing that came up was an old thread about someone asking for the system/cache/boot sizes.
Looks like no one really wanted it for this device.
I wish they did though, the Sense camera is amazing
Darin_Ram said:
I googled it, the only thing that came up was an old thread about someone asking for the system/cache/boot sizes.
Looks like no one really wanted it for this device.
I wish they did though, the Sense camera is amazing
Click to expand...
Click to collapse
I know what you mean. One reason I keep coming back to NRG is because of camera and video. I can't find a replacement that comes close.
Odysseus1962 said:
I know what you mean. One reason I keep coming back to NRG is because of camera and video. I can't find a replacement that comes close.
Click to expand...
Click to collapse
I've actually never flashed that one lol
But I was reading up and apparently there's a HD camera mod (can't remember if it was the desire or sensation) that was supposed to take better 1080p videos and superb photos.
I saw it floating the forums a while ago, but it was a sense cam so I couldn't flash it. I had Pac 4.3 at the time.
Now I'm on 4.4 Evervolv, so far so good. Lowest ram usage I've ever had with a lot of apps installed, so I'm happy with it.
I may or may not try Cyanogenmod 11 but I'm in no hurry.
Darin_Ram said:
Thanks again for the help, the phone is functional again. Does anybody have any idea why this happens?
Click to expand...
Click to collapse
No idea why it happens but I had the same symptoms - wouldn't get past the HTC logo but this happened after I had simply powered the phone off and removed the battery after I wasn't going to use it for a while [playing with the Lumia 920].
It seemed like the partition map gets wiped out or something causing the problem.
The hdd camera is in the aroma installer I'm my viper Rom.
Well also be the camera default in the upcoming release of jellybean sense and other future releases.
Sent from my HTC_Amaze_4G using xda app-developers app
chevycowboyusa said:
The hdd camera is in the aroma installer I'm my viper Rom.
Well also be the camera default in the upcoming release of jellybean sense and other future releases.
Sent from my HTC_Amaze_4G using xda app-developers app
Click to expand...
Click to collapse
Sounds good, but no kit kat?
One Rom at a time... Lol
Ravike and I have been working on this for a while now. Can't progress until we get the next level finished, then the next version will be hopefully easier. We are getting closer. Ravike has a lot of building from scratch to do.
Sent from my HTC_Amaze_4G using xda app-developers app
chevycowboyusa said:
One Rom at a time... Lol
Ravike and I have been working on this for a while now. Can't progress until we get the next level finished, then the next version will be hopefully easier. We are getting closer. Ravike has a lot of building from scratch to do.
Sent from my HTC_Amaze_4G using xda app-developers app
Click to expand...
Click to collapse
Ooooh
I used your rom, I love the full gpu rendering. Haven't tried the camera yet, but looking forward to that HD mod that's on there.
Nenamark2 gets 50.5 fps!!!!!!!!!! That's the most I've ever seen this device go up to!!!!
Damn! Awesome lol
Antutu shows that the graphics goes over the 4000 mark. Definitely love it.
Darin_Ram said:
Ooooh
I used your rom, I love the full gpu rendering. Haven't tried the camera yet, but looking forward to that HD mod that's on there.
Nenamark2 gets 50.5 fps!!!!!!!!!! That's the most I've ever seen this device go up to!!!!
Damn! Awesome lol
Antutu shows that the graphics goes over the 4000 mark. Definitely love it.
Click to expand...
Click to collapse
ViperAmaze was one of the first ROMs I tried when I got mine. I loved everything about it except I had Bluetooth pairing and WiFi tethering issues. Since I'm a truck driver, I need hands free on my daily driver. Unfortunately, it seems most if not all of the builds that are not derived directly from the OEM HTC Amaze, have some type of Bluetooth or WiFi issue that's not easily overcome.
TL;DWR: I want to go back to absolute zero and revert my phone to factory. I'm new to android and just followed a youtube video guide to root and unlock boot loader and now don't know how to go back.
Hey guys, I am completely new to android and have been with iPhone for about 7 years so please forgive me for my questions as they are elementary in comparison with the topics that are typically discussed on here.
I decided to switch it up and try an M8 cause the build quality and screen really excited me so I sold my iPhone and made the switch. I was in absolute love for about a week while on stock. Just learning android and all it's small quirks was fun for me.
but now, I have the phone up for sale, I'm amazed at how convoluted it is just to return to stock after rooting and roming. I spent 6 hours last night with a phone that wouldn't boot and just hang at the opening htc one opening boot animation.
I installed TWRP, unlocked the boot loader and used Hassoon2000's all in one toolkit to root as well. I used this video posted on the toolkit thread on here to help guide me.: https://www.youtube.com/watch?v=Krw6H4gQ6g0&feature=youtu.be
I followed the video to a tee with some stops on my side cause what he said in the video didn't always happen on my end, so I would unplug my phone and plug it back in and continue where I left off until the whole process worked. It's at the very end when he used twrp to reboot back into his "normal phone" that my phone just hung on the HTC boot animation.
I have all neccasary drivers and software installed to run this the toolkit and still received the "error: no device found" from time to time when using the kit. so you can imagine all the hair I pulled out coming from jailbreaking an iPhone with one click to trying just to root my device to disable ads and not can't even use my phone.
after some digging to find what I thought what supposedly a stock rom/img/Whateverthenameis for my phone, I breathed a sigh of relief and flashed it using tarp adb side load option and it finally booted up. I now however don't have working Wi-Fi and some apps that came preinstalled on my phone are missing. I don't like and just feel like it's a buggy mess.
long story short, I just want to go back to absolute zero. all the way stock; I don't even care about keeping any root or unlock. It would be nice so I can adblock but I don't care about it if it will stop me from going back to zero.
Here are all the tools I used to ruin my android experience aka the tools I mentioned above:
Toolkit (thread): http://forum.xda-developers.com/showthread.php?t=2699065
rom/img/whateveritscalled that i used to get back into a buggy phone: http://www.androidfiles.org/?developer=M8&folder=StockRoms
video guide I used: https://www.youtube.com/watch?v=Krw6H4gQ6g0&feature=youtu.be
I ran all this on a Windows 7 64-bit desktop machine.
Did you flash the Shipped RUU?
orangekid said:
Did you flash the Shipped RUU?
Click to expand...
Click to collapse
I barely understood how to flash the rom I found to get my phone back on but how do I flash an ruu and where do i get it?
orangekid said:
Did you flash the Shipped RUU?
Click to expand...
Click to collapse
I would also love to know how to do this, I desperately need help
I think there was a shipped RUU for the M8 that could be used to go full stock, I'll see if I can find it.
RUU = Rom Update Utility, which was named that back in the old WinMo days. This would just be a file that you either flash thru SD via fastboot or thru your computer.
orangekid said:
I think there was a shipped RUU for the M8 that could be used to go full stock, I'll see if I can find it.
RUU = Rom Update Utility, which was named that back in the old WinMo days. This would just be a file that you either flash thru SD via fastboot or thru your computer.
Click to expand...
Click to collapse
If you could find that it would be most appreciated
I just looked and couldn't find one. Would this be the only way to revert to stock from either a bad flash, boot loop or just plain want to be stock again. I want to root but I'm just not confident enough to use the toolkit without any handups. At least if I knew how to get back to stock I wouldnt worry as much.
Sent from my HTC One_M8 using XDA Premium 4 mobile app
Word around was that there has been no RUU released for our device yet. There is a stock rooted TWRP recovery image on the Android Development forum but that's probably the closest you will get. I'm not sure if a straight up factory reset would do it or not, but you would need to flash the stock recovery as well. Overall a pretty drawn out process, especially if you are unfamiliar with adb and fastboot. You might have to wait for a RUU
Sent from my HTC One_M8
TheEmpyre said:
Word around was that there has been no RUU released for our device yet. There is a stock rooted TWRP recovery image on the Android Development forum but that's probably the closest you will get. I'm not sure if a straight up factory reset would do it or not, but you would need to flash the stock recovery as well. Overall a pretty drawn out process, especially if you are unfamiliar with adb and fastboot. You might have to wait for a RUU
Sent from my HTC One_M8
Click to expand...
Click to collapse
What would happen if I clicked att software update in settings? would it do something or no? Would it crash the whole phone?
TheEmpyre said:
Word around was that there has been no RUU released for our device yet. There is a stock rooted TWRP recovery image on the Android Development forum but that's probably the closest you will get. I'm not sure if a straight up factory reset would do it or not, but you would need to flash the stock recovery as well. Overall a pretty drawn out process, especially if you are unfamiliar with adb and fastboot. You might have to wait for a RUU
Sent from my HTC One_M8
Click to expand...
Click to collapse
I thought I saw a leaked RUU floating around that did the job..
RACEnSK8 said:
What would happen if I clicked att software update in settings? would it do something or no? Would it crash the whole phone?
Click to expand...
Click to collapse
It probably would not find one, but if it did nothing good would happen, it won't successfully take an OTA with a custom ROM, recovery, etc..
Non-rooted nand backup,which can be used to go back to stock
http://forum.xda-developers.com/showpost.php?p=51953376&postcount=352
Wonders_Never_Cease said:
Non-rooted nand backup,which can be used to go back to stock
http://forum.xda-developers.com/showpost.php?p=51953376&postcount=352
Click to expand...
Click to collapse
I think I need to find someone to help me, because I never had to deal with rooted devices before. So i wouldn't even know what to do with the files you posted
RACEnSK8 said:
I think I need to find someone to help me, because I never had to deal with rooted devices before. So i wouldn't even know what to do with the files you posted
Click to expand...
Click to collapse
It's pretty simple actually.
If you are using TWRP recovery, just place this in that folder on your SD card, boot into recovery, and hit "restore"
it will restore a stock ROM on your device.
Use the recovery version he mentions though.
orangekid said:
It's pretty simple actually.
If you are using TWRP recovery, just place this in that folder on your SD card, boot into recovery, and hit "restore"
it will restore a stock ROM on your device.
Use the recovery version he mentions though.
Click to expand...
Click to collapse
How do I figure out what recovery i have
RACEnSK8 said:
How do I figure out what recovery i have
Click to expand...
Click to collapse
reboot the phone into recovery (your power menu might have the option) and it will give you the version.
You can also access it from fastboot, or adb (typy adb reboot recovery)
RACEnSK8 said:
I think I need to find someone to help me, because I never had to deal with rooted devices before. So i wouldn't even know what to do with the files you posted
Click to expand...
Click to collapse
Yea, android phones are a complete different world then that of iPhones. I was in your shoes a yr after the ip4 release. I didn't jump right in...I didn't flash or root my 1st phone for months. To be fair, not all android phones have difficult root/restore methods...most I've used were 1 click, same goes for jb programs. The only thing I can think of that iPhone had a slight edge was if you bricked from a bad app or jb...DFU and restore thru iTunes but then you worry about restoring to the new firmware...waiting for the next exploit and praying its not tethered. If iPhone is your thing...great but don't bounce from android after your 1st set back...it happens to all of us.
Sent from my HTC One_M8 using XDA Premium 4 mobile app
orangekid said:
reboot the phone into recovery (your power menu might have the option) and it will give you the version.
You can also access it from fastboot, or adb (typy adb reboot recovery)
Click to expand...
Click to collapse
I went into recovery and it says PhilZ Touch 6.25.5
Clockworkmod v6.0.4.7
nash2000 said:
Yea, android phones are a complete different world then that of iPhones. I was in your shoes a yr after the ip4 release. I didn't jump right in...I didn't flash or root my 1st phone for months. To be fair, not all android phones have difficult root/restore methods...most I've used were 1 click, same goes for jb programs. The only thing I can think of that iPhone had a slight edge was if you bricked from a bad app or jb...DFU and restore thru iTunes but then you worry about restoring to the new firmware...waiting for the next exploit and praying its not tethered. If iPhone is your thing...great but don't bounce from android after your 1st set back...it happens to all of us.
Sent from my HTC One_M8 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Yeah, luckily I went from WinMo to iOS, so I went from "if you flash one wrong file you're bricked" to "I cannot brick this device if I try"
coming back to Android was like the WinMo days.
Depends what you have too, my daily is a Nexus 5, pretty easy to do anything on it. Samsung are really easy too, you just Odin a factory tar no matter where you are for the most part.
But HTC is the difficult one, all these tokens and issues and hboot versions and patches etc...
You get used to it though, and then it doesn't seem so daunting...
In this case, these are things OP needs to know if he is going to mess with any Android phones, basic things like recovery and basic ADB / fastboot commands etc...
RACEnSK8 said:
I went into recovery and it says PhilZ Touch 6.25.5
Clockworkmod v6.0.4.7
Click to expand...
Click to collapse
Ok,
You need to flash TWRP:
http://forum.xda-developers.com/showthread.php?t=2695709
orangekid said:
Ok,
You need to flash TWRP:
http://forum.xda-developers.com/showthread.php?t=2695709
Click to expand...
Click to collapse
So how do I do that?
Sorry for being such a noob, but I just want my wifi to work lol