Related
Does the Gtab not support wireless N? Or is it Vegan5.1? I have a linksys WRT610N and I have my b/g on the 2.4Ghz and N on the 5Ghz but my Gtab doesn't pick the N SSID. Anyone know why this is?
tcoker79 said:
Does the Gtab not support wireless N? Or is it Vegan5.1? I have a linksys WRT610N and I have my b/g on the 2.4Ghz and N on the 5Ghz but my Gtab doesn't pick the N SSID. Anyone know why this is?
Click to expand...
Click to collapse
Nope, its got nothing to do with the rom you are running. The G-Tab is hardware limited to wireless G, no N. I was a little dissapointed by that too when I researched it to buy, but frankly G is fine for streaming vids, music, etc.
Most N routers support dual mode for legacy G devices so I'd suggest turning this on. Additionally if your router does not broadcast its SSID you'll have to manually type it in when setting up the wireless connection on your tab...
tcoker79 said:
Does the Gtab not support wireless N? Or is it Vegan5.1? I have a linksys WRT610N and I have my b/g on the 2.4Ghz and N on the 5Ghz but my Gtab doesn't pick the N SSID. Anyone know why this is?
Click to expand...
Click to collapse
My upstairs router is a WRT610N. My GTab works fine with it. The Gtab comes with a single wireless radio (does not support MIMO) that supports the Wireless-N (802.11n) draft standard.
The Gtab will only see the 2.4GHz band, not the 5GHz band.
Butch1326 said:
My upstairs router is a WRT610N. My GTab works fine with it. The Gtab comes with a single wireless radio (does not support MIMO) that supports the Wireless-N (802.11n) draft standard.
The Gtab will only see the 2.4GHz band, not the 5GHz band.
Click to expand...
Click to collapse
Oops, you're right, thats what I was trying to say, no 5Ghz frequency.... While it connects fine to my N router, it really isn't true N or any speed near it.
powercrazy said:
Nope, its got nothing to do with the rom you are running. The G-Tab is hardware limited to wireless G, no N. I was a little dissapointed by that too when I researched it to buy, but frankly G is fine for streaming vids, music, etc.
Most N routers support dual mode for legacy G devices so I'd suggest turning this on. Additionally if your router does not broadcast its SSID you'll have to manually type it in when setting up the wireless connection on your tab...
Click to expand...
Click to collapse
I have my routers on the 2.4GHz band setup for Wireless-N only, and my Gtab connects to them just fine. Both on my E4200 and my WRT610N.
powercrazy said:
Oops, you're right, thats what I was trying to say, no 5Ghz frequency.... While it connects fine to my N router, it really isn't true N or any speed near it.
Click to expand...
Click to collapse
Yeah, I only see 72Mbit/second, but someone else reported that they saw 270 Mbit/second connecting to their Netgear router.
I agree with you. I haven't seen the throughput, especially during large file transfers.
So once again the marketing monster strikes. Clearly states wireless N but only in the 2.4 Ghz range. That's fine just wanted to be sure there wasn't something I was missing. Thanks to everyone who replied.
tcoker79 said:
So once again the marketing monster strikes. Clearly states wireless N but only in the 2.4 Ghz range. That's fine just wanted to be sure there wasn't something I was missing. Thanks to everyone who replied.
Click to expand...
Click to collapse
N doesnt specify any frequency.
True but when anyone sets up a wireless N router on the 5GHz band only...it will not be found by the G-Tablet. I have mine set up with both 2.4GHz and 5GHz so all of my equipment is covered.
I'm using the WRT310N and I have mine set to Wireless N only.
Standard 20MHz Channel @ 2.412GHz
GTAB Connects.
Hell, if you live in an area where you can use all 14 2.4GHz channels you can even connect on channel 14. A lot less interference.
My gTab can see my N-network but it disconnect immideatly after I try to connect. I have 2 routers; 1 upstairs with N only, an done downstairs with both N & G. I'm mostly upstairs but I have to connect to the G-router which only gives me one bar.. But it works just fine, although full speed N would have been nice for Winamp Wifi-sync and transfering Movies etc
Mine connects to DLink Dir655 2.4Ghz rounter using N protocol but gTab radio definitely not a MIMO one.
Best download speed is about 2.7 - 3.0 MByte per second when using FTP, and only 1.9 - 2.0 MByte per second when using SMB protocol.
My laptop can get upload/download speeds around 9-10 MByte per second using same router and 2.4Ghz MIMO N wireless card.
I was wondering if any prime owners tryed to connect on a N-Only wifi?? on the box it says a/b,g,n wireless but when i try to set my wifi to N-Only, i can see the network but theirs no way the prime is connecting to it. I have to switch it back to either Mixed or G/N Mixed, and then im able to connect with a max connectivity with router of 54mbps. This problem was present before and after ICS update, my router is a Asus RT-N12 (tryed with stock firmware, updated stock firmware and with DDWRT). I Would like to know if any of you guys tryed this out I feel i'v been kinda scammed
PS. (I checked out on Q&A for the prime and couldnt find any post related to this if you guys know there is already one, please just give me the link i'll continu posting on the other thread thanks)
I can't connect to my "N" router either. Mine doesn't even show up in my TF.
is it a TF prime or the first one?
N-5ghz is not supported, putting it in 2.4Ghz mode should work (at least, it does on mine... whether there's a difference or not is another thing)
I can connect my prime to my router with N only as long as its on 2.4GHZ and between channels 1-11. I wish I could pick up 12-14 because I live in an apartment complex with crowded wifi. Router is Cisco E2000 with DDWRT firmware...
The link speed showing on the network signal app only maxes at 54 mbps though. I can stream 1080p mp4s from my network drive though so its fast enough for me...
RT-N12 is operating on 2.4ghz and does not support 5ghz. Are you sure you are in "N-Only" mode or are you in "Mixed"??
This has been discussed in great detail in general section. Its known Prime can't connect to 5Ghz. set it to 2.5 or G only. G only seems tl yield best results. also check this article out..might help.
www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-speed
Yes, it connects 2.5 N only but the performance is pathetic. Prior to ICS, I got curious changing my 2.5 GHz band to strictly G. Saw an immediate boost in performance + speeds.
Yes so far I am very disappointed. I just got the Prime today and it immediately updated to ICS. Once that was done I started checking out the wifi ability right away, because of all the bad reports all over the internet. Much to my surprise, mine doesn't see my wireless N either. I had the TF101 prior and it worked fine with my router. My Samsung E4GT phone sees it just fine, and what really hurts is my wife's iPad 2 sees it, connects to it and pulls just under 20mbps speeds.
To say this sucks is an understatement. I hate losing to Apple in any way, and here I am with the latest and greatest Android tablet, and being punked by a nearly year old IOS device.
Crap
I have no wifi issues with my N router... Performance can be a little better (speed wise) but no issues connecting at all, my router is cisco
Sent from my Transformer Prime TF201 using xda premium
wherestheanykey said:
Yes so far I am very disappointed. I just got the Prime today and it immediately updated to ICS. Once that was done I started checking out the wifi ability right away, because of all the bad reports all over the internet. Much to my surprise, mine doesn't see my wireless N either. I had the TF101 prior and it worked fine with my router. My Samsung E4GT phone sees it just fine, and what really hurts is my wife's iPad 2 sees it, connects to it and pulls just under 20mbps speeds.
To say this sucks is an understatement. I hate losing to Apple in any way, and here I am with the latest and greatest Android tablet, and being punked by a nearly year old IOS device.
Crap
Click to expand...
Click to collapse
What do you stream over 5ghz network to iPad? 1080p movies? It redundant...just turn down to 2.4 and everyone is happy.
Having a technically higher spec which does not improve on daily usage is redundant.
jedi5diah said:
What do you stream over 5ghz network to iPad? 1080p movies? It redundant...just turn down to 2.4 and everyone is happy.
Having a technically higher spec which does not improve on daily usage is redundant.
Click to expand...
Click to collapse
Exactly, the prime doesn't support the 5Ghz frequency. Only supports 2.5ghz N or whatever. There's only a few tablets that do actually support 5ghz. All it takes is a simple change n it'll work. THE whole argument that it should work on any network is b.s. Especially if you have it set to something not supported. Doesn't take a genius to figure that out.
I've always used N-Only. I get a decent connection to my Transformer Prime with it too.
Mines is the cheap Belkin N150 router so I doubt it does that 5Ghz range as that seem like a setting for a higher priced N router.
Scott1620 said:
I can connect my prime to my router with N only as long as its on 2.4GHZ and between channels 1-11. I wish I could pick up 12-14 because I live in an apartment complex with crowded wifi. Router is Cisco E2000 with DDWRT firmware...
The link speed showing on the network signal app only maxes at 54 mbps though. I can stream 1080p mp4s from my network drive though so its fast enough for me...
Click to expand...
Click to collapse
Point 1: Your are in the US, so you are not allowed using anything except 1-11 by FCC regulations.
Point 2: N-Only often turns on channel bonding in soho equipment like yours, so it needs 8 full channels to use it properly. Each channel is 5 MHz apart from the other and a WiFi device uses channels in a/b/g that are 20 MHz wide, in 11n with channel bonding (which is an optional feature for the high data rates) they use channels of 40 MHz. So dividing the 40 Mhz by 5 Mhz makes using of channel 14, 13, 12, 11, 10, 9, 8, 7. If you would live in Japan, on only country that is allowed to use channel 14. So for US it would be channel 11-4. This explains why channel bonding in the 2.4 GHz band is a band ides unless you are living in a big ranch 500 feet away from the next WiFi router.
---------- Post added at 11:28 PM ---------- Previous post was at 11:24 PM ----------
the_game_master said:
I've always used N-Only. I get a decent connection to my Transformer Prime with it too.
Mines is the cheap Belkin N150 router so I doubt it does that 5Ghz range as that seem like a setting for a higher priced N router.
Click to expand...
Click to collapse
Cool device, taken from the specs page of belkin.com:
Security: Wi-Fi Protected Setup, 256-bit WEP (64-128bit), WPA-PSK (TKIP), WPA2- PSK (AES) with WPS Push Button
Range of up to 1,000 ft.
Link Rate: Up to 150Mbps in 40MHz Channel Mode Bandwidth 20 MHz & 20/40 MHz auto
ISP Protocols Supported Dynamic, Static, PPPoE, PPTP, Telstra Bigpond, L2TP
Compliant Standard IEEE 802.11b, 802.11g
So no 11n support per specs, but the Overview page tells 150 MBits are supported, so it can run 75 Mbits without channel bonding and 150 with.
Try out the WiFi Widget it tells you the data rate to the WiFi router.
jedi5diah said:
What do you stream over 5ghz network to iPad? 1080p movies? It redundant...just turn down to 2.4 and everyone is happy.
Having a technically higher spec which does not improve on daily usage is redundant.
Click to expand...
Click to collapse
I spent the extra money to purchase a dual band router, so I could broadcast N and G as two separate signals. As I understand it, if you broadcast both on a single signal, and you have some older devices that require and connect to the G band, it will automatically cut the speed back, to whatever the slowest device connected is capable of. At least that is the way it was explained to me. So the N was on 5ghz and G was on 2.4ghz. It has always worked with any other wireless N device I have had, until I got this "latest and greatest" tablet. So yes now I have downgraded my wireless network to only 1 band, to accommodate the Prime.
wherestheanykey said:
I spent the extra money to purchase a dual band router, so I could broadcast N and G as two separate signals. As I understand it, if you broadcast both on a single signal, and you have some older devices that require and connect to the G band, it will automatically cut the speed back, to whatever the slowest device connected is capable of. At least that is the way it was explained to me. So the N was on 5ghz and G was on 2.4ghz. It has always worked with any other wireless N device I have had, until I got this "latest and greatest" tablet. So yes now I have downgraded my wireless network to only 1 band, to accommodate the Prime.
Click to expand...
Click to collapse
If you have 2.4ghz g network, prime should be able to detect it. Check if your dual band is working properly...
Wireless n is impt only if you stream HD movies. I stream music on g with no problem at all.
I know you feel frustrated, and I know it sucks as prime is supposed to be PRIME. If you intend to stream HD movies to prime you may have to "down grade" to 2.4ghz if not wireless N is kind of overrated or "miss used" as I see no use of having to stream HD to non HD devices. If you are a home theater enthusiastic or business it then wireless n 5mhz is a must.
Hope you can move on to appreciate the quad core of prime than dwelling on this issue.
Cheers!
dagrim1 said:
N-5ghz is not supported, putting it in 2.4Ghz mode should work (at least, it does on mine... whether there's a difference or not is another thing)
Click to expand...
Click to collapse
Dah!!
I just open a new thread for this very issue.... I'm sure I'm going to get ding for it.
any way...
Mine doesn't connect to the "N" wireless
My router hosts "N" and "a/b/g" modes cisco 3200
it only connects to the 2.4 Ghz a/b/g mode...
Desn't work even if I set the "N" mode to 2.4 Ghz channel and turn OFF the a/b/g mode.
PuroKaibil said:
Dah!!
I just open a new thread for this very issue.... I'm sure I'm going to get ding for it.
any way...
Mine doesn't connect to the "N" wireless
My router hosts "N" and "a/b/g" modes cisco 3200
it only connects to the 2.4 Ghz a/b/g mode...
Desn't work even if I set the "N" mode to 2.4 Ghz channel and turn OFF the a/b/g mode.
Click to expand...
Click to collapse
You right about getting ringed..lmao. I just posted to your thread. 5Ghz N range is marketing b.s. its way overhyped n not as good as people think anyways. Read this tech article to get the real scoop on it and tips.
Www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-speed
demandarin said:
You right about getting ringed..lmao. I just posted to your thread. 5Ghz N range is marketing b.s. its way overhyped n not as good as people think anyways. Read this tech article to get the real scoop on it and tips.
Www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-speed
Click to expand...
Click to collapse
I did read it and thank you at the other thread....
Great Read...
Thanks again.
Ok guys I read somewhere in here that the Prime did not play nice with Wireless N so here is what I did using my D-link wireless router:
Changed wireless settings from N to G only and ran some tests here is what i got:
WiFi Analyzer - -50/-44 dbm
Speedtest.net- Ping 17ms 8275dn and 2125up Average ( I have a 8Mb connection)
GPS Test - it now can see 9 sats and lock to them but the signal is still very poor (between 10 /20 SNR) so the navigation dops the signal but IT CAN SEE THE SATS!
Changed wireless G to N and this is what I got:
WiFi Analyzer - -61/58 dbm ( the lower the number the better the signal)
Speedtest.net- Ping 72ms 6420dn and 1233up Average ( I have a 8Mb connection)
GPS Test - 0 sats
Changed the wireless N to N+G and this is what I got:
WiFi Analyzer - -55/50 dbm
Speedtest.net- Ping 24ms 8225dn and 1790up Average ( I have a 8Mb connection)
GPS Test - It can see 4 sats but wont lock
What does it all mean???? I have no idea, all i know is that im going to leave my router on G from now on.
Can anyone else confirm and post? Thanks
>What does it all mean???? I have no idea, all i know is that im going to leave my router on G from now on.
It shouldn't matter. N's main advance over G is its MIMO transmission, 5GHz inclusion, and doubled bandwidth (40MHz) mode (some turbo-G versions have channel bonding, but they were proprietary and not interoperable between brands). The Prime has a single xmit/2 rcv ant (nix MIMO), single-band (nix 5GHz), and only works with 20MHz bandwidth. You should not notice a difference between N and G wrt the Prime. In fact, as the majority of wifi in laptops and PCs are of the cheaper single-band variety, this applies to those as well.
Many early N routers are draft-N, and N mode can be problematic, especially in mixed mode use. That's probably why some people noticed an improvement when they switched to G. Many people also use TKIP in WPA/WPA2, which also leads to slowdowns.
To answer your question directly, sure, change the various settings and see if they make a difference. But if you get an improvement in G over N, it probably means you should upgrade to a newer router--or at least find an updated firmware if one is available. The improvement would apply to other devices and not just the Prime.
BTW, since wireless performance is highly variable, you would want to take a number of tests and take the avg, rather than rely on a single reading.
That was a helpful post E.mote, thank you.
e.mote said:
>What does it all mean???? I have no idea, all i know is that im going to leave my router on G from now on.
It shouldn't matter. N's main advance over G is its MIMO transmission, 5GHz inclusion, and doubled bandwidth (40MHz) mode (some turbo-G versions have channel bonding, but they were proprietary and not interoperable between brands). The Prime has a single xmit/2 rcv ant (nix MIMO), single-band (nix 5GHz), and only works with 20MHz bandwidth. You should not notice a difference between N and G wrt the Prime. In fact, as the majority of wifi in laptops and PCs are of the cheaper single-band variety, this applies to those as well.
Many early N routers are draft-N, and N mode can be problematic, especially in mixed mode use. That's probably why some people noticed an improvement when they switched to G. Many people also use TKIP in WPA/WPA2, which also leads to slowdowns.
To answer your question directly, sure, change the various settings and see if they make a difference. But if you get an improvement in G over N, it probably means you should upgrade to a newer router--or at least find an updated firmware if one is available. The improvement would apply to other devices and not just the Prime.
Click to expand...
Click to collapse
or maybe is one more thing that the primes have wrong with them...don't get me wrong I love my prime and I DO NOT WANT TO GET RID OF IT i just wish there were some answers to all of our questions or maybe i should stay away from all the forums and pretend that there is nothing wrong with it and the $500 was money well spent. Thanks for your input
router is 2 weeks old and it has the latest firmware. (first thing i checked) the post does say Average.
Wireless N 5Ghz is so overhyped n overrated. It get less range than the 2 4Ghz band.
Read this tech article that shows how most people got scammed by 5Ghz band hype.
http://www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-speed
demandarin said:
Wireless N 5Ghz is so overhyped n overrated. It get less range than the 2 4Ghz band.
Read this tech article that shows how most people got scammed by 5Ghz band hype.
http://www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-speed
Click to expand...
Click to collapse
I work in IT field and deal with plenty of routers I will take G over N any day range is always much better which explains why Prime works so much better with G because of the aluminum backplate blocking some of the Wi-Fi signal the range isn't as good as your everyday Wi-Fi device dead spots about 10 ft difference.
Maybe this doesn't apply to some but with wireless g my speed tests are at about 15-20mbs and with N its the full 36-42 mbs. So if your internet is slower than 20mbs g is probally fine but I NEED n to work to get the most out of my connection.
Sent from my Transformer Prime TF201 using Tapatalk
So ive got 20mb internet and have the virgin media hub, wireless connection is awful upstairs, do i go with n or g and is the prime not compatible at all with n
The Prime operates in the 2.4ghz band, forget the 5ghz, it will do nothing for your Prime, I also made tests to my network and disconnected the 5ghz band after getting results like the OP. ATM, my network operates G only and I'm getting great results.
Cheers
Spurs027 said:
So ive got 20mb internet and have the virgin media hub, wireless connection is awful upstairs, do i go with n or g and is the prime not compatible at all with n
Click to expand...
Click to collapse
I would definitely go with wireless N. If you have problems like very slow speeds switch back to G.
The prime seems to support wireless N speeds up 65 mbs.
Sent from my DROID RAZR using Tapatalk
>with wireless g my speed tests are at about 15-20mbs and with N its the full 36-42 mbs.
N has better throughput and range, assuming good antennas on both ends that allow for MIMO/dual-stream use. G is needed for legacy pre-N devices. I use both.
>wireless connection is awful upstairs
Options to boost wifi in your home:
. Try a different router. Routers can vary in performance.
. Repeater (old router retrofitted with DD-WRT firmware) to extend your router's range. Repeaters aren't common as consumer products nowaday, since they need some knowledge to set up.
. Powerline adapters (pair). These are convenient but relatively expensive. Advertised for ~200Mb/s, but more realistically 100-150. They're getting more common; most vendors have a line. Performance depends on house electrical wiring.
. MoCA adapters, assuming house is wired for cable-TV (RG-6 coax). These can also be expensive, but you can hunt around for older stuff on eBay for cheap. It's more reliable than powerline.
I dropped 802.11g long ago like it was hot like I did 802.11b before it.
802.11n is now, the Transformer prime supports all of them and changing wireless broadcast to anything lower than N is just to give you less of what's current and best.
the_game_master said:
I dropped 802.11g long ago like it was hot like I did 802.11b before it.
802.11n is now, the Transformer prime supports all of them and changing wireless broadcast to anything lower than N is just to give you less of what's current and best.
Click to expand...
Click to collapse
Not really if the devices you own don't "see" the 5ghz frequency, only but the newest electronics operate on that band, you Prime don't for example, and it's new.
Cheers
After reading this I was interested to see if this was having any effect. I tried several different settings:
G - only
N - 20MHz (single channel)
and N - 40Mhz (channel bonding)
I found that by far the best setting was single channel N. I've gone from having virtually no usable connection in parts of my house, to a usable throughput in all parts of the house. Also did some tests using WiFi analyser and speedtest.net and found consistently higher throughput and signal strength using this setting.
My conclusion, it seems to have a problem with wireless N channel bonding.
PrimeUser said:
Not really if the devices you own don't "see" the 5ghz frequency, only but the newest electronics operate on that band, you Prime don't for example, and it's new.
Cheers
Click to expand...
Click to collapse
I don't have a dual band N router but if I did I wouldn't set it to operate in 5Ghz only mode, I would keep it functioning as a dual band mode so both 2.4 and 5 Ghz bands were active for complete 802.11n functionality.
That way all my N devices would see the N broadcast.
That's the point, I do have a dual band router, I tested the network with both frequencies on, and disconnected the 5ghz band after testing the 2.4ghz alone, the network signal is weaker with both on.
If you stream alot of video and have devices capable of taking advantage of the higher frequency, very well, if you don't or don't stream that much video anyway, having the 5ghz on, doesn't make any sense. In my case, weakens my signal, it works for me to shut it down, maybe for others this doesn't apply.
Signal strength depends of so many factors, the environment where a network is set, strongly dictates the outcome in performance and stability of it, no network behaves the same. My network is working in top condition for the environment around it, that's what it matters for me.
Cheers
Just got this phone today,
I have a Netgear R6300 capable of AC wifi but my phone wont connect to the internet when its on the 5ghz network. It works fine on the 2.5ghz but the other it connects but no internet.
I tried giving it a reserved ip and looking at the settings on my router but nothing is popping out at me?
Anyone have any ideas?
HTC One on Rogers network (Canada)
WakeTurbulence said:
Just got this phone today,
I have a Netgear R6300 capable of AC wifi but my phone wont connect to the internet when its on the 5ghz network. It works fine on the 2.5ghz but the other it connects but no internet.
I tried giving it a reserved ip and looking at the settings on my router but nothing is popping out at me?
Anyone have any ideas?
HTC One on Rogers network (Canada)
Click to expand...
Click to collapse
Check the Advanced Wi-Fi settings. Check Freq Band and make sure it is not set to 2.4 GHz only. Also try turning on "Best Wi-Fi Performance" and see if that helps.
Mine connects to my 5GHz network with no problems at all.
Hope that helps.
kevinrstruck said:
Check the Advanced Wi-Fi settings. Check Freq Band and make sure it is not set to 2.4 GHz only. Also try turning on "Best Wi-Fi Performance" and see if that helps.
Mine connects to my 5GHz network with no problems at all.
Hope that helps.
Click to expand...
Click to collapse
What router do you have? Also what kind of connection speed are you getting?
I checked freq and it was on auto, tried just 5ghz, also tried Best wifi but it still cant connect to the internet. I gets a connection with the router according to the phone but my 6300 doesnt show it as a connected device.
no problem here i can connect to my 5Ghz network with my a/n capable Time Capsule router. speeds are 55..27 Mbps download / 35.95 Mbps upload. my One wifi settings are set to Auto (vs. setting to 2.5 or 5 Ghz).
I have a Netgear WNDR4500. Speeds are 40 Mbps down and 28 Mbps up. That is with the router 2 floors above me in my house. My settings are also set to "Auto" as well. I connected immediately when I got home on Thursday after getting the device. I have had no problems at all with WiFi. Sorry I cannot be of more assistance.
I have no problem when connecting to my R6300 in AC mode ...
mine connects just fine
No connection at 5ghz, can only connect at 2ghz
I have d-link dr-825 rev B router with [DD-WRT v24-sp2 (04/01/13) std - build 21153] firmware. It has dual 2ghz and 5ghz radios.
I can only connect at 2ghz and unable to connect at 5ghz.
I have a dell latitude laptop and my old Galaxy SII has no problem connecting.
Howvever Htc-One lists the access point, correctly determines what kind of security is on (like wpa/wpa2 etc) but is unable to connect. I think once I saw a brief flash saying authentication failure on my phone when trying to connect to 5ghz. So I removed all security and made it completely open just to try. Again no connection without any error.
I am thinking of returning it if it is going to be a problem.
---------- Post added at 12:17 PM ---------- Previous post was at 11:40 AM ----------
Ok, I have solved the problem, now it is connecting. I made two changes in the wirless setup. Enable RTS/CTS protection and also enabled short preamble. After these two changes it is connecting as expected.
WakeTurbulence said:
Just got this phone today,
I have a Netgear R6300 capable of AC wifi but my phone wont connect to the internet when its on the 5ghz network. It works fine on the 2.5ghz but the other it connects but no internet.
I tried giving it a reserved ip and looking at the settings on my router but nothing is popping out at me?
Anyone have any ideas?
HTC One on Rogers network (Canada)
Click to expand...
Click to collapse
I'm having the same issue with mine and the same router, can not quiet figure out what is going on.
Just quick update i just did an update on my router and it seems to connect completely fine
For those who have router issues, check for a firmware update! Most routers have a few updates while sitting on the shelf. I used to always update and properly configure routers (with out the software disc) for customers at my old job and we rarely had problems of customers bribing it back. And throw out the disc that comes with the router. The software can cause headaches down the road. All security settings can be done inside the router through any web browser and router IP.
Just got a black ATT HTC ONE, everything is great, but no connection to 5ghz network here either.
I have a Netgear WNDR3700 and just updated to the DD-WRT build 21676, and still no go...
All our macbook airs are working fine on the 5ghz...:cryingrobably time for a new router lol
Connects to my linksys ea6500 5ghz ac just fine link speed around 400 mbps
Sent from my HTC One using XDA Premium HD app
Added an Airport Express, and 5ghz works fine from that...
cq_ said:
Just got a black ATT HTC ONE, everything is great, but no connection to 5ghz network here either.
I have a Netgear WNDR3700 and just updated to the DD-WRT build 21676, and still no go...
All our macbook airs are working fine on the 5ghz...:cryingrobably time for a new router lol
Click to expand...
Click to collapse
Prefers 2.4
I have a dual band N router, and my One seems to "prefer" connecting to the 2.4 GHz network over the 5 GHz.
It will work fine on the 5GHz, but I have to switch it manually when I walk in the house (so I usually don't).
I guess I could just tell my phone to "forget" the 2.4 network to fix this. On more thinking, maybe it's a coverage thing - it probably finds the 2.4 GHz network first. Lower frequencies penetrate walls better, right?
doxy-LS said:
I have a dual band N router, and my One seems to "prefer" connecting to the 2.4 GHz network over the 5 GHz.
It will work fine on the 5GHz, but I have to switch it manually when I walk in the house (so I usually don't).
I guess I could just tell my phone to "forget" the 2.4 network to fix this. On more thinking, maybe it's a coverage thing - it probably finds the 2.4 GHz network first. Lower frequencies penetrate walls better, right?
Click to expand...
Click to collapse
Correct. The 2.4 GHz network should travel further. Its all about that sweet sweet 5 GHz speed though! Mine connects to my Asus RT-AC66U router just fine.
doxy-LS said:
I have a dual band N router, and my One seems to "prefer" connecting to the 2.4 GHz network over the 5 GHz.
It will work fine on the 5GHz, but I have to switch it manually when I walk in the house (so I usually don't).
I guess I could just tell my phone to "forget" the 2.4 network to fix this. On more thinking, maybe it's a coverage thing - it probably finds the 2.4 GHz network first. Lower frequencies penetrate walls better, right?
Click to expand...
Click to collapse
You could always set it to 5ghz preferred. Mine connects to my netgear 5ghz ac router with no issues. Also if you have the same password for both frequencies it could just be connecting to that first.
Sent from my HTC One using Tapatalk 2
no preferred option?
godfirst said:
You could always set it to 5ghz preferred. Mine connects to my netgear 5ghz ac router with no issues. Also if you have the same password for both frequencies it could just be connecting to that first.
Sent from my HTC One using Tapatalk 2
Click to expand...
Click to collapse
I did check when sitting in my driveway - the 2.4 GHz network was still 2 "arcs" there & the 5 GHz was just a dot, so I think it is connecting to the first one it finds & sticking with it. In the Wi-Fi preferences, the "Wi-Fi frequency band" options are only Auto/5 GHz only/2.4 GHz only. No 'preferred' option - I'm running stock though - is there something different in the custom ROMs? I'm not afraid to root/ROM - I just haven't seen a good reason yet.
doxy-LS said:
I did check when sitting in my driveway - the 2.4 GHz network was still 2 "arcs" there & the 5 GHz was just a dot, so I think it is connecting to the first one it finds & sticking with it. In the Wi-Fi preferences, the "Wi-Fi frequency band" options are only Auto/5 GHz only/2.4 GHz only. No 'preferred' option - I'm running stock though - is there something different in the custom ROMs? I'm not afraid to root/ROM - I just haven't seen a good reason yet.
Click to expand...
Click to collapse
Use the only 5ghz only. There's a big difference with custom roms and stock att at the moment. There's new firmware etc. 2.4Ghz has more penetration through walls then 5Ghz. That's why you have more bars of one and not the other.
Sent from my HTC One using Tapatalk 2
godfirst said:
Use the only 5ghz only. There's a big difference with custom roms and stock att at the moment. There's new firmware etc. 2.4Ghz has more penetration through walls then 5Ghz. That's why you have more bars of one and not the other.
Sent from my HTC One using Tapatalk 2
Click to expand...
Click to collapse
Well I want to be able to use the 2.4 GHz networks when available, so I'll leave it on auto. I guess the speed isn't a huge deal when the wireless connection is so much faster than my internet connection.
And yes, I know that there are lots of differences between stock & custom ROMs (my last phone was a Nexus S & I was always changing ROMs). What I meant to ask was if there was a difference with that specific option.
wifi 2.4GHz connection problems
Welcome
I have silver One for 3 weeks now, but it was 2 weeks in service - they reinstalled software and returned phone. No change.
I can't connect to any 2.4 Ghz network (G/N) ending Authentication Error. Only 5GHz works.
I tried it with Netgreat WNDR4700 (Gargoyle custom software), CISCO access point @ work, also random WiFi open networks in shops/malls, etc. Other devices i know and have at home ( Samsung Note II, htc Sensation, Acer Iconia tab, Dell Latitude laptop) works fine. Just the One cosing problems.
I run stock rom, how can I turn on more verbose logging or see what is happening in the Operation system while connecting? I must prove to Regenersis Poland service that my phone does not work. Otherwise they will say phone works within parameters.
Just got my Nexus 9 today from Google Play store UK. Everything seems working ok, except:
I cannot find any wifi 5GHz. I am connecting to my home 5GHz (Virgin Media Superhub) from my HP Pavillion laptop, MBP, iPhone and iPad. But on Nexus 9, I am not able to scan any 5GHz network:
2.4Ghz works fine though:
I have enabled all possible channels in Settings (Wifi Analyzer):
In system Settings, I have tried both Automatic and 5GHz only:
I have performed OTA updated after first time switched on device and connected to 2.4GHz network at work, didn't notice whether there was an issue on 5GHz until I got home.
So, is there a problem with the latest OTA, or simple this unit needs to be RMA?
BR/Richard
Hi
richardman said:
Just got my Nexus 9 today from Google Play store UK. Everything seems working ok, except:
I cannot find any wifi 5GHz. I am connecting to my home 5GHz (Virgin Media Superhub) from my HP Pavillion laptop, MBP, iPhone and iPad. But on Nexus 9, I am not able to scan any 5GHz network:
2.4Ghz works fine though:
I have enabled all possible channels in Settings (Wifi Analyzer):
In system Settings, I have tried both Automatic and 5GHz only:
I have performed OTA updated after first time switched on device and connected to 2.4GHz network at work, didn't notice whether there was an issue on 5GHz until I got home.
So, is there a problem with the latest OTA, or simple this unit needs to be RMA?
BR/Richard
Click to expand...
Click to collapse
Mobile devices don't always support all the 5GHz channels that an access point might use. Try setting the Access point to use the lowest channel, say 36 and see if that works?
Regards
Phil
PhilipL said:
Hi
Mobile devices don't always support all the 5GHz channels that an access point might use. Try setting the Access point to use the lowest channel, say 36 and see if that works?
Regards
Phil
Click to expand...
Click to collapse
Hi Phil
Thanks for the hint. It looks like Nexus 9 only able to see channel 34 ~ 48. My broadband AP has selection of 36 ~ 136, and it was on "Auto Performance" and auto selected channel 100 tonight.
Thanks Phil!
BR/Richard
Yeah.. Only 34-48 Weird why it doesn't support more than that.
Hi
Steffe89 said:
Yeah.. Only 34-48 Weird why it doesn't support more than that.
Click to expand...
Click to collapse
Different countries have different requirements, but often most countries only allow certain frequencies to be used outside, and other frequencies for 5GHz may only be used inside buildings to prevent interference to radar etc.
A mobile device can of course be used outside, so can end up only being setup to use much fewer frequencies than a router designed for indoor use.
Sometimes the router isn't set to the right country, so ends up using frequencies it shouldn't really be using with the mobile device correctly set so ignoring those frequencies or the other way around. 5GHz is a lot more complex for what frequencies can and can not be used, see here http://en.wikipedia.org/wiki/List_of_WLAN_channels and the chart at the bottom, you'll understand why 5GHz devices sometimes don't see each other, it's a lot more confusing than 2.4GHz.
Regards
Phil
Using 5ghz wifi
Hi
To use 5ghz have you tried configuring from WIFI from settings - tapping the three dots next to the magnifying glass - Advanced - WIFI Frequency band.
It gives you the option of selecting 2.4 or 5 or both.
Ron..
PhilipL said:
Hi
Mobile devices don't always support all the 5GHz channels that an access point might use. Try setting the Access point to use the lowest channel, say 36 and see if that works?
Regards
Phil
Click to expand...
Click to collapse
i had the same problem! Thank you so much for the fix!
You should be able to use channels 149-161 as well, it's the channels in between that are set aside for DFS and radar, so many devices don't support them.
Working fine for me on Channel 153 with a Nighthawk R7000.
Sent from my Nexus 9 using Tapatalk
its suposed to work check if your router router chanel are setup correctly
Got mine to connected on the Virgin Media Superhub by changing the channels as suggested. Can confirm it works but very unstable and keeps dropping connection.
I got the same problem.
I got the same problem! I bought my N9 on Nov 11 and used 5GHz without problem until today. In the WiFi Analyzer suddenly can show 2.4GHz only. I have reboot and clear all WiFi App cache & data., still cannot show.
Even connect to 2.4GHz, it took long time to Connect and Authenticate the connection.
richardman said:
Just got my Nexus 9 today from Google Play store UK. Everything seems working ok, except:
I cannot find any wifi 5GHz. I am connecting to my home 5GHz (Virgin Media Superhub) from my HP Pavillion laptop, MBP, iPhone and iPad. But on Nexus 9, I am not able to scan any 5GHz network:
2.4Ghz works fine though:
I have enabled all possible channels in Settings (Wifi Analyzer):
In system Settings, I have tried both Automatic and 5GHz only:
I have performed OTA updated after first time switched on device and connected to 2.4GHz network at work, didn't notice whether there was an issue on 5GHz until I got home.
So, is there a problem with the latest OTA, or simple this unit needs to be RMA?
BR/Richard
Click to expand...
Click to collapse
Been a while, but since this is one of the top Google results, and I've been pulling my hair for a couple of hours without finding a solution online, I thought I might chime in with what I found.
If your N9 is not seeing certain 5GHz channels, what is your model, WiFi or LTE? Also, apparently there is an "international" version of the LTE one, which I just got (I'm in the US) because it was cheap, and I didn't mind it affecting certain LTE bands, but I didn't think it would affect WiFi. In any case, the solution was to simply insert a SIM card from my region (T-mobile US) and the missing 5GHz networks appeared in the list. I don't have a solution if this is happening with WiFi-only Nexus 9's though.
You need to insert the SIM after turning on the tablet. If you turn it on with the SIM inserted, it won't show the hidden 5GHz channels. You can just reinsert it, or toggle off/on airplane mode though.
I also googled to see if there was an app to change Wifi regions, but the only one I found (from XDA) requires root, and doesn't work for this particular problem anyway.
Well I have never been able to connect to the 5ghz channel until now. Finally! Changing the router to use channel 48 for the 5ghz and it is running as expected. I love fixes like this.
Hamm1701 said:
Well I have never been able to connect to the 5ghz channel until now. Finally! Changing the router to use channel 48 for the 5ghz and it is running as expected. I love fixes like this.
Click to expand...
Click to collapse
Do you have a Wi-Fi or LTE model? If you have an LTE model have you tried inserting a SIM card like I said in the post above? I got access to the upper channels which are supposed to be higher performance. From 149 to 161.
whats the highest linkspeed you guys are getting? my nexus 6 gets 866Mbps , i guess it dpends on your AC router specs mine is ac1750 i think
what app do i use to check what channel my nexus 9 is connected to? i think its below 36
andy o said:
Do you have a Wi-Fi or LTE model? If you have an LTE model have you tried inserting a SIM card like I said in the post above? I got access to the upper channels which are supposed to be higher performance. From 149 to 161.
Click to expand...
Click to collapse
Wifi model for me
cobyman7035 said:
whats the highest linkspeed you guys are getting? my nexus 6 gets 866Mbps , i guess it dpends on your AC router specs mine is ac1750 i think
what app do i use to check what channel my nexus 9 is connected to? i think its below 36
Click to expand...
Click to collapse
I use netgears wifi analyzer.