Well I've tried like 45 roms in my Sgs2, I feel that my phone isn't as he was at start....I want to renew it..is there any way to remove everything, kernel root, old roms file, everything just to be with clean Stock ics..?
Well, I have tried over 45 different roms in my gs2, I feel that my cell phone isn't as he was at first.
I want to renew it ... Is there a way to remove everything? kernel, root, old roms file just everything and to be with clean stock ics..?
Thanks in advance
Question = Q&A
....................................
Clean Slate for those that balls up the firmware
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
Remove battery
Boot to download mode
Open Odin
Install correct stock firmware .
jje
Related
Trying to install themes on the S2 and everytime I keep getting bootloop no matter what theme it is. Tried an ICS and also the Ultratoxic themes
What I am thinking of doing is a wipe data/ factory reset in ClockworkMod mode then load up the Rom via Odin and then flash the theme
Will this work or does the wipe data also delete the back ups created with CWM?
Anything else that maybe causing boot loop?
On UltraToxic Rom and latest Siyah Kernel
The bootloop might be caused if you use a SystemUI.apk/Framework different than the one supported by the ROM.
Clean Slate for those that balls up the firmware .Or need to return to service or decide if its hardware/firmware problem .Or even just to clear out old roms etc .
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
Remove battery
Boot to download mode
Open Odin
Install correct stock firmware .
Still problems use usb jig to set rom counter to zero .
Return to service centre .
Or throw in the Liffey .
jje
If the theme is not made for you rom, then you get bootloops.
If the theme is made for you rom and you still get bootloops, wipe the cache and chances are it will boot.
Lennyz1988 said:
If the theme is not made for you rom, then you get bootloops.
If the theme is made for you rom and you still get bootloops, wipe the cache and chances are it will boot.
Click to expand...
Click to collapse
The theme is made for my Rom [ROM][2.3.6][XWKK5] UltraToxic Rom v8.0.1 - Lite'ning Themed
I have tried the themes and did the whole wipe cache etc and developer still does not know why I am getting bootloop?
If I do the below what odes the format cache do that is different than wipe it
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
Remove batteryBoot to download mode
Open Odin
Install correct stock firmware
Will hold of on throwing it in the Liffey expensive phone and Ireland is broke
Hello,
Before flashing a new kernel today, I kept getting random reboots and and I thought the kernel might be playing up (I didnt install any new apps or modify anything before hand). So I installed the latest Siyah kernel (Siyah-v3.2-CWM) and now when I load up my phone, I go past the lock screen and I just keep getting multiple closed messages for different applications. I also cant open any of them as I get a message saying "Unfortunately, [app name] has stopped".
I cant open Titanium Backup so Im screwed
Please help.
I have also tried wiping both caches but it hasnt worked / reset init.d file (if that helps?)
Flash back your old kernel, at least you'll be back where you started.
oinkylicious said:
Flash back your old kernel, at least you'll be back where you started.
Click to expand...
Click to collapse
That didnt work
....................................
Clean Slate for those that balls up the firmware .Or need to return to service or decide if its hardware/firmware problem .
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
Remove battery
Boot to download mode
Open Odin
Install correct stock firmware .
Still problems use usb jig to set rom counter to zero .
Return to service centre .
jje
iv been having a few issues as of late with my s2 so decided id just backup my numbers and media and wipe and start again, but when i do a factory reset, it shows an error mounting the sdcard/.android_secure
and then it skips it, can anyone tell me how to fix this problem so i can start a fresh with a nice clean and empty galaxy
What system do you have? ics or ginbread...?
Question = wrong forum.
....................................
Clean Slate for those that balls up the firmware .
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
Remove battery
Boot to download mode
Open Odin
Install correct stock firmware .
jje
my apologies, i havent used the forum much as the phone has been fine for about 6 months, its now on checkroms v6 which i managed to flash onto it with a bit of fiddling, thinking that may solve some of my issues but it didnt. thats when i noticed this error when doing a few resets.
JJEgan, gonna follow your steps now buddy, thanks and fingers crossed
its a no go, it wont let me format or mount the sdcard
try factory reset from phone menu,
try another kernel to get another version of CWM, eg: Siyah
hiya zac, well i have the phone in download mode connected to odin, im using the link in your sig, and downloading the stock firmare and kernal, will it matter if i didnt wipe the sdcard before flashing these two items with odin? surely i can do it after?
upto you to try.....
cant guarantee since dont know what weird problem has got with your SD card which
dont allow you to wipe,
you can also try flashing another custom kernel first,
When you flash a stock firmware it already contains a Kernel, no need to flash seperately..
any chance to a quick link to a kernal to try and a guide!
its been a while since iv done this! haha
which rom are you currently on?? ICS or GB
checkrom v6 i do believe
GB CWM flash : http://gokhanmoral.desean.net/siyahkernel/v2.6/Siyah-v2.6.14-CWM.zip
Checkrom is GB version,
but makesure, from settings/about phone
i will bud, and i flash that kernal, with odin?
no this is CWM flashable, put on SDcard, and flash from CWM,
top man, off to have a go now
if CWM flash fails, you can try from ODIN
ODIN flash :http://gokhanmoral.desean.net/siyahkernel/v2.6/Siyah-v2.6.14.tar
select the file from PDA of Odin,
Pugme said:
its a no go, it wont let me format or mount the sdcard
Click to expand...
Click to collapse
Unless you have a external sdcard, this problem is self explanatory!
Hey guys!!!
New galaxy S2 owner. I have done some searching in these forums and the threads answered many of my questions. However, I still have some newbie questions that I found unanswered. Please excuse me if my questions have been answered before but I got tired of searching
Here is the deal:
Yesterday, I flashed a CF Root with Odin3. Then used CWM to flash a wanamlite firmware. The firmware was great but I didn't like that it still had TW. So I dl'ed another firmware to the internal SD card and flashed again using CWM. I then flashed a couple of other ROMS and I noticed that after the first wanamlite flash, the new ROMs were unstable with many error messages that some OS processes have stopped etc.
I got back home, flashed to stock with Odin3 and the phone got stuck at the second samsung logo. I followed some community steps (thanks XDA) like disabling all kies processes from TM, wiping data/cache, then boot in DL mode and flash the stock ROM using Odin3 which worked.
I then Flashed a CF Root again and used CWM to flash a Spike Pure ICS ROM v5 which was great but I get occasional error messages like 'gallery stopped' or some other error message when I try to set contact photos. It just lags, blackscreen then comes back with the 'Unfortunately, the process had stopped'.
My questions: is this because of the previously flashed firmware that this is happening or is it that those ICS ROMs have these issues commonly? Did anyone have this experience before? What do you advice before flashing to a new ROM going back to stock or going straight from the current? Doesn't Odin3 technically wipe everything back to stock?
WIPE WIPE WIPE.
Go into recovery. Data/factory reset.
Advanced, Wipe dalvic cache. Mounts and storage, format system. Its a standard procedure going from one OS to another OS. You can then either flash a firmware zip from recovery or an .tar file from Odin.
Then to be on the safe side factory reset once again.
Sent from my GT-I9100 using Tapatalk 2
Wich fw do you have?
Make a deep clean with odin an flash on the latest ics version (lp9 is a good one)..then flash (if you want) a custom rom..
My experience with custom roms: one of the best rom samsung based (ics 4.0.3) is the foxhound greyfox v2..if you want a pure ics rom flash the omega aokp rom (ics 4.0.4)..
Try then to change kernel..siyah is the best for both roms..
P.s. sorry for my bad english
Sent from my GT-I9100 using Tapatalk 2
After LP7 should be staple enough for daily use .However you are using custom roms and you should read carefully each roms thread before flashing .
You are probably suffering from flashing multiple roms and leaving bits behind as well = clean wipe .
jje.
Can someone give me a clear full wipe procedure? I always wiped data/factory rest/wiuped chaceh and dalvik... but what else? a step by step procedure would be helpful!!
I currently have Spike Pure ICS v 5.
What do you mean by Odin3 'deep clean'?
OJ77 said:
Can someone give me a clear full wipe procedure? I always wiped data/factory rest/wiuped chaceh and dalvik... but what else? a step by step procedure would be helpful!!
Click to expand...
Click to collapse
Read my last post..
Sent from my GT-I9100 using Tapatalk 2
so:
1. Recovery mode > format user data > wipe cache > clear dalvik > format system (from moutns and storage)
2. Download mode > flash stock ROM using odin 3
Did I get it right? Was there something i didn't wipe?
Before you flash a new rom, make sure you answer the requirements.Some ICS roms need to be flashed in specific way.
The way of doing a full wipe is you go in Clockwork mode, wipe data/factory reset, you wipe cache partition, then go to advanced wipe Dalvik and Battery stats, then go in mounts and storage ( i think ) and you wipe the cache from there, but nothing else in mounts and storage.If you wipe anything else there's a high percent of bricking your phone.If this doesnt help you, I doubt that anyone could give you any clearer instructions.
Good luck.
DONT FORMAT SYSTEM.
....................................
Clean Slate for those that balls up the firmware .Or need to return to service or decide if its hardware/firmware problem .
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
Remove battery
Boot to download mode
Open Odin
Install correct stock firmware .
Followed by root and custom rom if you so wish .
jje
OK im confused now... do I format system directory in mounts and storage or no?
OJ77 said:
OK im confused now... do I format system directory in mounts and storage or no?
Click to expand...
Click to collapse
i always do personally.
I got tempted and formatted system/cache/data but now i cannot flash from my internal sd card.. I get errors and 'installation aborted' if i try to do it from CWM... does that mean formatting those 3 means Odin3 is the only way? Cus I'm not home and I don't have odin3 on me.... LOL!
OJ77 said:
I got tempted and formatted system/cache/data but now i cannot flash from my internal sd card..
Did you format sd card and totally wipe the lot = nothing on the phone .
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
At this point you have no OS on the phone nor kernel rooted nor CWM .
Hence
Remove battery
Boot to download mode
Open Odin
Install correct stock firmware .
Click to expand...
Click to collapse
JJ, you really need to learn how to quote you know, makes your posts so confusing to read sometimes
skimminstones said:
JJ, you really need to learn how to quote you know, makes your posts so confusing to read sometimes
Click to expand...
Click to collapse
Agree must try better .
Habit from replying to emails i guess .
jje
Thanks...
I did a 'full wipe' by doing t his:
1. Boot into CWM: wipe data, wipe cache, wipe dalvik, wipe battery stats, wipe system/data/cache from mounts.
2. Reboot into DL mode, flash stock ROM using Odin3.
3. Repeat step 1
4. flashed spike ICS v 7.3 using CWM. Stable so far.
Thank you!
imho: the most stable ics release is the stock official, but with some.battery issues, my suggestion: stay on gingerbread, find a custom kernel to suits your need,
GT-I9100, official 2.3.6, hardcore's Speedmod
budi.hermawan said:
imho: the most stable ics release is the stock official, but with some.battery issues, my suggestion: stay on gingerbread, find a custom kernel to suits your need,
GT-I9100, official 2.3.6, hardcore's Speedmod
Click to expand...
Click to collapse
I agree! I don't like ICS because is still unstable! My battery lasts very short with ICS and the phone overheats.
Moreover I hate the browser! I mean, The Galax S2 with GB still has the smoother browser of all the smartphones out there, and Samsung with ICS update messed it up! Now is laggy with micro stutters! Don't understand why!
OJ77 said:
The firmware was great but I didn't like that it still had TW.
Click to expand...
Click to collapse
You didn't need to go through all that trouble just because you didn't want TW (which I also hate, btw).
You could simply have installed another launcher (such as Go Launcher EX, ADW, etc) from Play Store and, since you were already rooted, uninstalled TW using Titanium Backup afterwards. It has to be in that sequence (install new then uninstall old).
this way you can have whatever ROM + kernel combination you like, and still use whatever launcher you prefer.
Hello every one.
I have a Samsung Galaxy S III international 16 gig white.
Yesterday I tried to flash FoxHound 1.1 on my device & because this version is full wipe I must flash the I9300XXBLG1.
After ending installing FoxHound 1.1 I face with a lot of FC & I couldn't play any games like Max Payne ,N.O.V.A 3 & etc.
When I play any game I face strange error!
After that problems I tried change ROM & fix my device but when I flashed every ROM & after factory reset with code the language of my device is same Philippians in I9300XXBLG1 & I have that error in Games.
I tried every thing like Full wipe ,Format system,reset Factory with code,flashing with PIT,install CM9(I fix same problem in S II by flashing CM9 or AOSP rROMs but in S III...) & etc.
Now I have this issue & need a solution.
What is your Answer?
SORRY For my poor English.
With 30 posts you should ask in that rom thread re its problems .
Its noticeable that flashing multiple roms to fix a problem cannot work .
....................................
Clean Slate for those that balls up the firmware .Or need to return to service or decide if its hardware/firmware problem .
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
Remove battery
Boot to download mode
Open Odin
Install correct stock firmware .
Still problems use Triangle Away to set rom counter to zero flash stock rom .
Return to service centre .
jje
JJEgan said:
With 30 posts you should ask in that rom thread re its problems .
Its noticeable that flashing multiple roms to fix a problem cannot work .
....................................
Clean Slate for those that balls up the firmware .Or need to return to service or decide if its hardware/firmware problem .
Backup data first if phone is working .
Boot CWM recovery
Mounts and Storage
Format cache data system sd card .
Remove battery
Boot to download mode
Open Odin
Install correct stock firmware .
Still problems use Triangle Away to set rom counter to zero flash stock rom .
Return to service centre .
jje
Click to expand...
Click to collapse
Not working!It's very very serious problem & bothering me!