so today i recieved a notice of an update on my tf201. My tablet is fully stock non rooted and i trusted the actual asus update to work. it downloaded and installed but then hung on the finishing booting screen for 2 hours. reset the tablet and now it boots up goes through the setup wizard and when u click finish it says setup wizard has stopped and goes to a blank black screen. i can still access the settings and notification bar but nothing else. i cant seem to downgrade roms as it was never rooted. somebody PLZ help asap as this is driving me insane!
well i managed to get it reverted back to .15 from this guild http://www.youtube.com/watch?v=A8R2D8xlbDk well see if upgrading again ruins it all over again
Just do the manual upgrade from Asus website. For some reason, some of the OTA updates were corrupt or not complete. Upgrade through Asus website n you will be fine.
Related
Hey,,
So I received my G tab today and connected it to the internet and downloaded the update (Tap UI V.1.1-3588).
However, after the update got applied, when I try to turn on Wifi it says error. I tried to restart the device twice and on both times the wifi worked and actually connected to my network but then disconnected and went back into displaying the error in matter of seconds. I have searched the forums but it seems no one with stock Rom have had this problem.
Thanks in advance
I had issue with the stock fw, never ever after 3588 was ok, even when reinstalling
Try a new firmware. Maybe
Sent from my UPC300-2.2 using Tapatalk
I've got the same issue here. After restart I have Wifi for a couple minutes then it disconnects and errors until the next restart. This is my second G-tab and my first one works great.
P.S. Other ROMS didn't help my condition so you may want to pursue return before attempting Rom upgrade. I'm back to bone stock and still not joy.
It works now !
All what I did is close the wifi as soon as it starts, gave it a minute then turned it on.
Now I'm not sure if I should do this each time i boot it up, but, it works !
Try doing that, maybe it was by chance that it worked with me .
So my 10.1's been stuck at 46% on the 3.2 update now for about an hour. Has anyone had as long of a delay?
Not sure how long to wait or, really, what if any options I have...
TIA
I am installing the update right now through OTA.
For me it stayed in '46%' only for a couple of minutes. Now i am at '51%'
I have heard it takes a while, I'd sit tight if you are still waiting...
On another note, does anyone know if this update to 3.2 breaks root?
*EDIT* Did update, root not lost.
Update: Called Samsung tech support. They instructed that if the update hangs the fix is to just turn the tab off and then on again. Update started again and completed without error.
I turned on my Prime this morning as usual routine, to get a little work done, and I was prompted for a camera firmware update. When it completed downloading, I received no usual prompt to install? Prior to download it stated the usual "approximate 10 minute installation during which your tablet will be unusable" blah blah blah, but when I clicked the download complete text in my notification bar, it just cleared it? I then went searching for it in my download app, in my files, & my file explorer. I didn't see it anywhere? I did a shutdown & restart but still nothing. I'm boot loader locked, not rooted, completely stock ICS, firmware 9.4.2.15, with camera version TF201-0x9900.
I don't know if its possibly related, but when I first received this prime, my second one, I did have trouble getting the camera firmware upgrade to install. It took several tries on Honeycomb, & then a few more on ICS before it took. I believe this was because I; didn't allow 15-20 minutes of downtime for it to sync with Asus/Google servers, which I believe is necessary with any device out of the box, especially when it has major updates immediately.
If anyone has any knowledge of this update, or any idea what may have went wrong, I would greatly appreciate your advice. Thank you to all in advance, your input is valued.
Sent from my Asus Transformer Prime
same camera version here TF201-0x9900
checked for update: not available
location: holland
website doesn't mention it either yet
Before Christmas I tried to do a OTA update on my Prime, which has not been successful and I have not been able to use the Prime since.
It has previously been rooted and previously have always been successful in using Voodoo OTA Rootkeeper to retain root after updates. I've not unlocked the Prime.
Now when I try to boot it spends a while 'optimizing' the applications (as if it was the first time i've booted it since the update), and then once it is started, no apps will startup, all of them resulting in saying "unfortunately xyz has stopped"
A video of the problem: youtu.be/e1yfTtGiR78 (sorry can't post full link as am a new user).
I'd like to get it working again, possibly installing the Androwook ROM (or at the very least, just working on the stock rom). What steps do I need to do from where I am at the moment?
There are many threads about flashing roms, brick-fixing (some more up to date than others), but I'd just like a bit of advice about this problem and what I should do next (maybe some good links?). I haven’t gone near doing any flashing on the Prime, and it would be nice to seperate the things I could do, from the things I -should- do (I don't know where to start).
I believe as the Nvidida logo is on the bottom right this means I'm on the JB bootloader? Currently the settings menu shows I'm on android 4.1.1, but not sure if this is pre or post the failed update.
Thanks for any help,
Steve
A factory reset will fix you up. You'll lose your data
Hold vol down + power when booting to access the boatloader menu. Select wipe with vol down and use vol up to confirm.
Hi,
Thanks, I've done the reset, but I still seem to have the same problem.
imageshack.us/photo/my-images/502/imag0217c.jpg
I can't actually proceed throuh the inital set up, because it closes itself when it gets to the account setup page.
Any ideas?
I have resolved this.
I downloaded the latest firmware from the ASUS support website, extracted the zip file from within the downloaded zip file and renamed it to EP201_SDUPDATE.ZIP .
Put this on a microSD card (which I had formatted to FAT32), inserted it into the Prime, then booted into the bootloader menu.
Selected the RCK option, it did the update, and 10 minutes later it was up and running again.
From what I have read, it won't try to complete the update if it thinks you have already got that version installed already, but I guess it knew it hadn't successfully completed the update previously.
Glad it's working again.
Hello everyone!
I'm having some trouble right now, My phone was updated with the AT&T update because my phone prompted me about the update. I updated my phone and successfully updated the phone. I installed all of my backup apps from Titanium back, but when I restarted my phone after the apps were installed my phone booted up but said that NFC stopped working dailer stopped working,basically everything was not working - i couldnt even do anything with the phone. What I did was I tried doing a factory reset via TWRP but it didn't work. I also cleared the Dalvik and Cache but didnt work either.
I locked my bootloader and thought I would flash the RUU for my device. everything went fine untill the RUU displayed an "unknown bootloader version". I tried downloading the RUU again but it didnt seem to work.
I installed Elegancia through ADB install went through perfectly untill I reboot into the phone the HTC screen with the white background does not go anywhere. I occasionally get a pop up that says "stopped responding would you like to stop the program". I downloaded the Mongoose custom rom for my phone, again install went fine no problems. but once again when I boot into the phone I still get stuck on the HTC white background. This time the phone has a black screen with the status bar with the icons of the battery time and an x on the signal icon then the phone restarts.
What is going on with my phone? How can I reinstall an OS and get my phone working again?
any help would be greatly appreciated!
Since you have done the update, you will have to flash the ROM of this thread, everything you need to know is in this post.
Lucky Thirteen said:
Since you have done the update, you will have to flash the ROM of this thread, everything you need to know is in this post.
Click to expand...
Click to collapse
Thank you so much it worked perfectly!!
Any reason why the other ROMS didn't work?
Glad it work!
Please edit your OP title and write : [Solved] Any way to bypass HTC setup screen? Stuck on HTC logo all white.