Since I've been on smart phones, I've moved all my music to those and shunned my now broken iPod away.
I've had issues with the original Droid's headphone jack, but what Droid owner didn't? I was able to deal with annoying static though, and simply forcing it closer to the contacts by sliding a piece of plastic in there helped a lot.
When I got my RAZR Maxx it was so much better. Once I found out how to get my bass back, I was in love. I was a bit worried about having a similar issue as with my Droid though as I listen to music with the phone in my pocket with a lot of movement. I'm usually riding bike after all.
I haven't had much of an issue for a while now, but recently things have turned south.
While I was on GB, using Skullcandy Ink'd ear buds, the slightest little movement of the plug could stop my music's playback, no matter what app I was using, (tested in Winamp, Pandora, My Music, and Power Amp) and eventually it would start launching the Voice Commands app. Other times, I could move the plug as much as I wanted and it wouldn't do a damn thing but play my music, which is exactly what I wanted.
I recently upgraded to ICS leaks and froze the Voice Commands app with Titanium and succeeded only in having the music stop as if I had unplugged it.
Once my gf killed my ear buds, I upgraded to Skullcandy Heavy Medals which seemed to fix the issue out right.
Once again though, I am having the same issue as before. I can get set on my bike, ride for a while listening to music fine as can be. Once I stop for any reason, if I move my leg at all, there's a good chance the music will stop as if I had removed the plug...
I know the plug is not damaged, and I've not done anything major to the jack to damage it.
Is there anything I can to do help prevent this? Any ideal ways of removing any lint that might be in there?
I don't really have time to take off my glove, fish my phone out, and press play again at 30 MPH in traffic...
This RAZR is the only phone I've ever had problem with lint and dirt getting into the headphone jack. I used air from a compressor, and a small spring, and just twisted it around until I got it all out.
Not exactly responsive to your query (about the headphone jack), but have you considered bluetooth stereo earbuds like these? You need to follow that link to Amazon and see all the pictures before you reject this flat out. You can wear these inside your bike helmet, while the bulk of the device will ride around your neck, below your helmet. My best friend has them and loves them. They have ridiculously long battery run time. The sound quality is good (acc. to my friend). If you were connecting by B/T, there would be nothing to plug into the headphone jack.
Not the solution you were looking for, but might solve your problem.
Related
I was on my nightly bicycle ride using Cardio Trainer and my Skull Candy Smokin Buds, and everytime id move the phone in my bicycle jersey near the headphone jack it would cause the music to skip/stop/ff sometimes try to voice search and sometimes try to redial out ... I can replicate the problem here at home by jiggling the headphone jack around abit .......... anyone else
Yes. I posted the exact same thing in Q&A forum. Got no response but I figured it out.
Sometimes when you plug in your headphones they are detected as a headset. It doesn't occur that often, just make sure the notification icon doesn't have the microphone part. Otherwise any shaking causes songs to skip, phone to freak out and voice dialer starts.
Apparently there's also an app that makes sure they always do connect in headset mode. I think I'll go replace my phone anyway.
Sent from my PG86100 using XDA App
I had the same thing happen yesterday. I was testing some speakers at a job site and the phone was going CRAZY. I pulled the phone out of the otterbox case and re-plugged the headphone in and it was fine. I think my problem was the case + cable was not making the correct contact. Today I had the headphones from a PSP plugged in (with case) and it was fine.
Looks like its the same thing that was heading to my evo4g. The headphone input is design for 3 ring conductor (for remote control) but your headphone jack has 2 ring conductor thus making your phone act weird. I brought an adopter (you can go search amazon) and it fixed the problem.
go to marketplace and download "headset blocker". it wont show up in your apps list. go to 1 of your homescreens, and add its widget. its a toggle that you turn on and off. when its on, none of the headphone control features will work, and it it should just play your music without skipping tracks and what not.
I have the same issue did you ever figure it out?
Like previously mentioned this is because it is designed for a 3 ring conductor. 1 is left, 2 is right, 3 is microphone/control. The controls are back track, forward track, pause/play/answer/hangup. If you have a pair of headphones with 2 conductor (which is fine and it is also designed for) you are good. If, however, you aren't making full contact (because of cases being in the way or you have a 'non standard' headphones, read: cheap ****) wacky things can happy from intermittent contact of the various points.
I've never experienced this on either phone, but, it is a thing and it makes perfect sense.
There is another possibility...that the jack is fncked up. Poorly soldered, defective jack, abused (all it takes it one good jerk on the cable to ruin everything).
It's not as random and wacky of a situation as it sounds like.
I have two different 2 ring (stereo) headphone cables from two different manufacturers and the cable has nothing to do with the issue in my case. The issue is not with headphone/earbuds and not with the cable not plugging in all the way. The issue for me is that when you have the headphone cable plugged into the jack and the other end is feeding any type of amp: stereo equipment, Aux input in a car, whatever, the phone absolutely loses its mind. I've tested it on three different phones now and it does it every time. The phone is unusable until you download, install, and activate Headset Blocker from the market. Then everything works perfectly. It appears to be a defect in either the hardware or the software because it is picking up electrical noise as headset control signals.
BTW, I've measured the cables and tested to be sure they plug in all the way. They are standard 2 ring (which means three conductor) cables that should not be triggering any headset functionality. Something on these phones is falsely triggering the headset connection: maybe some very small electrical signal or voltage coming from aux inputs because as I said, earbuds/headphones with the exact same connector don't have the problem.
Mike
I had the same problem and just swapped it for a new phone. If you're still under 30 days just take it back.
mikeyxda said:
I have two different 2 ring (stereo) headphone cables from two different manufacturers and the cable has nothing to do with the issue in my case. The issue is not with headphone/earbuds and not with the cable not plugging in all the way. The issue for me is that when you have the headphone cable plugged into the jack and the other end is feeding any type of amp: stereo equipment, Aux input in a car, whatever, the phone absolutely loses its mind. I've tested it on three different phones now and it does it every time. The phone is unusable until you download, install, and activate Headset Blocker from the market. Then everything works perfectly. It appears to be a defect in either the hardware or the software because it is picking up electrical noise as headset control signals.
BTW, I've measured the cables and tested to be sure they plug in all the way. They are standard 2 ring (which means three conductor) cables that should not be triggering any headset functionality. Something on these phones is falsely triggering the headset connection: maybe some very small electrical signal or voltage coming from aux inputs because as I said, earbuds/headphones with the exact same connector don't have the problem.
Mike
Click to expand...
Click to collapse
It sounds likely that it could be a grounding issue, probably on the amp side...though it could be on the phone side, especially if this happens to some phones and not others. If this is pro gear there is probably a ground lift switch on the back...give that a shot, if it doesn't help then it is definitely the phone...which I am leaning towards since it seems to happen on some and not others.
Headset Blocker from Market. I had a video on youtube about this and my thread is here.
i am having the same problem. thanks for the heads up for the headset blocker app. beats using up warranty or paying deductible for now.
I know this thread is 2 years old, but I figured bumping is better than starting a new thread. Anways, this issue has been driving me crazy to no end. Headset blocker stops the false signals. However, if it's in your pocket and the base of the jack is bent, (at least on Skullcandy products + HTC Inspire), music stops playing from the left ear.
Anyways, I figured out a solution to this. Cut a 3.4mm hole in a credit card, and then insert your headphone jack. Trim the card around where you insert the headphone jack. To get the right size hole, I use a knife to penetrate the card, and then use a screwdriver to widen the hole until it's about right. It should stop all interference and false signals, audio cutting when your phone is in your pocket and the headphone base is bent.
This also works on heaphones that have microphones; however, you have to remove the plastic piece if you want to use the mic.
Abaout those adapters on Amazon that someone mentioned; what do I search to find them?
daneurysm said:
It sounds likely that it could be a grounding issue, probably on the amp side...though it could be on the phone side, especially if this happens to some phones and not others. If this is pro gear there is probably a ground lift switch on the back...give that a shot, if it doesn't help then it is definitely the phone...which I am leaning towards since it seems to happen on some and not others.
Click to expand...
Click to collapse
Nope, it's certainly on the phone side.
I've had the same issues plugging it into my car and into professional audio equipment.
Headset blocker is great. I just keep it on all the time.
It was pretty funny sitting in the car and realizing that it's dialing everyone on your contact list though. Couldn't make it stop even after unplugging it. It went crazy.
DjDom said:
Nope, it's certainly on the phone side.
I've had the same issues plugging it into my car and into professional audio equipment.
Headset blocker is great. I just keep it on all the time.
It was pretty funny sitting in the car and realizing that it's dialing everyone on your contact list though. Couldn't make it stop even after unplugging it. It went crazy.
Click to expand...
Click to collapse
i have the exact same thing on my device, but it happens with any headphones i have plugged in
moving them just a bit causes google now to launch repeatedly and the music to skip,play,pause,etc
to fix it i remember using a blocker from the market and editing the code that launches google now via headphones so the blocker would block it aswell
I'm not sure if this has to do with the x2 or just cm7 but I can't seem to figure it out. The audio without headphones is perfectly fine, but with them only the instrumental parts can be heard occasionally you can hear kind of a digital chirp of the vocals.tried figuring it out in dsp and music settings but nothing. Any advice on this is very much appreciated.
Sent from my DX2 w/Cm7 using XDA App
No problems with or without my headphones under CM7. Maybe your headphone port is bad?
Have you tried hooking up a different pair of headphones to see if it might be the headphones or the connector?
Have you tried it under a different ROM to see if you're getting the same problem?
Is this something that you only experience when listening to music with your headphones? Try checking the audio port to see if its got any lint in it. You can clear it out with a paperclip and you might be surprised to see how much has built up. It'd also be a good idea to test your phone with other headphones.
If this is happening with/without headphones, I'm not sure what would cause this. Maybe try a different music player?
It's happening to me, only on CM7
Skelente said:
Is this something that you only experience when listening to music with your headphones? Try checking the audio port to see if its got any lint in it. You can clear it out with a paperclip and you might be surprised to see how much has built up. It'd also be a good idea to test your phone with other headphones.
If this is happening with/without headphones, I'm not sure what would cause this. Maybe try a different music player?
Click to expand...
Click to collapse
This happened to my Inspire 4G with CM7.1. The problem dissappeared upon installing ICS with aospX and kept working fine with IceColdSandwich, but several other problems forced me to return to Gingebrear. Now with CM 7.2 the problem is again.
It is not a total attenuation. It is a DSP setting that seems to be optimized for karaoke, because it selectively suppresses voice frequencies. However, all settings in DSP manager are turned off. Turning on Stage Virtual Room barely improves it. I can hear some voices, but really bad.
I think it's probably your headphones wearing out. I had a similar problem and a new pair of headphones immediately fixed the issue.
you got a case on that phone? I stopped using my otterbox 'cause every time i plugged in headphones, they'd act very stupid (sometimes giving the "no vocals" thing, sometimes cutting in and out)
I've also noticed that some headphone jacks don't do a good job of locating themselves and you can actually push them too far in.
I use a set of samsung headphones that have four contacts on the 3.5mm jack instead of the typical Tip-ring-sleeve three contact design. these are the ONLY headphones I have used that give me zero problems (unless I use the otterbox case along with them)
between the stupid angle on the hole for the 3.5mm jack on the phone, and a plethora of minute differences between jack designs, generally the X2 and headphones are a marriage made in hell...
stereo bluetooth works perfectly however
EDIT: Moderators, please feel free to move this thread to the troubleshooting/Q&A forum. I didn't realize it might belong there... Sorry!
OK so I got a new HTC One and so far I love it in all aspects except... the following:
With a headset plugged in to the headphone jack (earbuds with in-line mic and button) any amount of jostling or rotation of the plug in the jack causes my phone to skip songs, stop playing music, and begin redialing the last call in my call log. This issue makes the phone practically unusable for listening to music, as even the slightest shaking of the plug (i.e. from phone in pocket while walking, movement of headphone cord from turning head left or right while sitting still, etc) causes problems.
I thought it was a problem with the individual device I got so T-Mobile was nice enough to send me a new HTC One...
And it has the exact same problem.
I have tried several different headsets with button and mic. Notably, all of the headsets with mic I've tried all work flawlessly on all other devices.
Has ANYONE had this problem?
Note that I Intend to record a video of the problem for evidence, but I'm pretty convinced its a design flaw in the HTC One.
At this point I have all intention to go with a different device, as much as that pains me to say (probably the Xperia Z)
EDIT2: After some experimentation, I have discovered the problem. It is a ridiculous design flaw on the part of HTC. I will post pictures later along with videos. In theory it can be remedied with a new set of headphones of a certain style or possibly some electrical tape or other insulating material, but I really don't think that should be a requirement of using the HTC One.
EDIT4: See here for my post on reddit with a description of what I believe to be the cause of this problem: http://www.reddit.com/r/htcone/comments/1k6ia1/illustration_of_a_design_flaw_with_the_htc_one/
And here is a link directly to the photo album on imgur with descriptive captions: http://imgur.com/a/uXvn3
i just picked up a set of ear bud n mic headphones today and played music and did voice commands with it today and had no issues but it was a short period of time...i will try to replicate ur issue and report back later today.
its a issue with something of htc software i believe. it was doing similar with my skullcandy ink'd second gens.
i looked into it a lil but not alot. but it seems only certain headset/earbud combos work properly. i really dont know why theyd have it like that. but for me i had to play around with the mic button and what not.
It's the head set I have earbuds and soul, soul works fine
Sent from my HTC One using Tapatalk 2
I've run into this problem on other phones before, but it was always the 3.5mm jack. Either it was tarnished or the case/jack design combo was causing it to not seat fully. Check very closely that the jack is fully seated and maybe try with another set before condemning the jack in the phone as bad.
I believe I have diagnosed the cause of this and other problems. Please see the OP for links to photo album with descriptions.
I purchased mine back in june and never had this problem. Ive used 2 pairs of headphones with the device (some $5 kyocera promo headset from when I worked at metropcs and a pair of Sony MDR-XB500). Only thing I could think of would be faulty software/hardware (phone jack) combination.
LifeEscalade said:
I purchased mine back in june and never had this problem.
Click to expand...
Click to collapse
yeah , it's right.
I have this very issue on my HTC one Since my wife's HTC one doesn't experience it with the same headphones I just concluded it was some tolerances that were off on mine I mainly use Bluetooth so I didn't feel it was a big enough issue to return. I had originally searched to see if it was a widespread issue, but could not find any others who had it.
I have not had the problem, either with a headset or an AUX cable I use for my car stereo. The headset jack on mine fits very snug and the plug does not touch the housing except maybe a very small area where the lip is metal.
I just got an htc one and I use my headphones while riding my motorcycle to work. I've only used it twice and both times my music skips around erratically. I'm using google play with music saved on my device. I came from a galaxy s3 that didn't have this problem. Does anybody have any experience with this and a solution? The weird thing is, I can't recreate this when sitting on my couch.
Edit: using stock headphones. I tried using my old s3 headphones and they wouldn't work at all.
vvelvetelvis said:
I just got an htc one and I use my headphones while riding my motorcycle to work. I've only used it twice and both times my music skips around erratically. I'm using google play with music saved on my device. I came from a galaxy s3 that didn't have this problem. Does anybody have any experience with this and a solution? The weird thing is, I can't recreate this when sitting on my couch.
Edit: using stock headphones. I tried using my old s3 headphones and they wouldn't work at all.
Click to expand...
Click to collapse
Sometime when you slide your headphones into the jack you can inadvertently scratch the protective paint inside the jack. This metal on metal connection causes your phone to react erratically. Especially with the vibration of your motorcycle. There's a couple ways to remedy this. One is to place a small piece of electrical tape to cover up the exposed metal inside your phone jack. I don't really like this method becaue it could dislodge and fall into the headphone jack and prubably cause more issues. I'd suggest you go to the play store and download a program called "WizDroid (No Headset Control!)." It will block all signals from your headset so that your phone will act normally again. Only downside is hat you can't your headset controls to pause/skip tracks or answer calls.
Link
Wizdroid (No Headset Control!)
indoz said:
Sometime when you slide your headphones into the jack you can inadvertently scratch the protective paint inside the jack. This metal on metal connection causes your phone to react erratically. Especially with the vibration of your motorcycle. There's a couple ways to remedy this. One is to place a small piece of electrical tape to cover up the exposed metal inside your phone jack. I don't really like this method becaue it could dislodge and fall into the headphone jack and prubably cause more issues. I'd suggest you go to the play store and download a program called "WizDroid (No Headset Control!)." It will block all signals from your headset so that your phone will act normally again. Only downside is hat you can't your headset controls to pause/skip tracks or answer calls.
Link
Wizdroid (No Headset Control!)
Click to expand...
Click to collapse
thank you for you reply and i will try that. i have an update. only happens when im on my motorcycle. i can sit on the couch and move the jack around in the hole (phrasing) and there is no skipping or any problems. i can get on my bike and go the mile on the street to the freeway with no problems. but once i get up to speed (around 50mph) it starts to skip around. i am going to try using the headphones in a car to see if it happens when i get up to speed then. if so it might be a location thing. but i really doubt that.
update: rode to work today with an old set of skullcandys that do not have a mic and only has one side working and i had no problem. i find this to be really weird, but, what ever. i can get a new pair of no mic headphones. i never use the headphones to talk anyway.
I use an aux cable in my car to listen to music and podcasts.
when starting spotify i experienced incredible amounts of static, no matter what volume both the phone and car volume were set at.
Anybody else experience this?
Experiencing this in my work truck, will check my car after work
Sent from my LG-H830 using Tapatalk
Works fine in my car. Must be something else
Sent from my LG-H830 using Tapatalk
napafats said:
Works fine in my car. Must be something else
Sent from my LG-H830 using Tapatalk
Click to expand...
Click to collapse
Might be the worst static and fuzz ive ever experienced through a phone. Dont know what to do.
Any updates on this?
Mine comes out with an incredibly small amount of movement. Anyone else have this issue?
Nvm I just was being too easy on it. Requires a lot of pressure relative to anything else I've had for it to lock in.
Also you guys should dip a q-tip in rubbing alcohol and clean out your cars and phones headphone jacks. Especially in a work truck I imagine there's significant dust build up in there.
....cable
I found this too, even the headphones supplied need a fair amount of force to connect - at least they won't be pulled out so easy!
1 Maybe RF from cell communication leaking into audio or power cable.
2 Try with phone Not plugged into car power (I assume you run this with charger cable connected).
3 Try with better quality aux cable, maybe one that is shielded.
No fix. so aggravating.
Mine are flawless.
I just got the g5. Same issue. Tried multiple cables. Headphones work fine but not the aux cable
Just got my G5 a few days ago and I noticed this too.
In the car using a downloaded playlist on spotify and got terrible static noises (haven't tried any local music files as I don't use any!)
Sent from my LG-H850 using Tapatalk
I tried it in another head unit and it works.
Aux cable works in my Alpine but not in the Kenwood.
Ok guys and gals. I've been dealing with this for a bit and I found a fix of sorts. First off, two G5s (a buddies and mine) both had static in my car, but no static in his car or my mother's car. The difference being is that I have an aftermarket JVC player (removable face plate, auxiliary jack in front). The other two cars had factory stereos. I was guessing it was an aftermarket thing. Weird, I know, but that was the only commonality. Even more odd was that out of four phones the G5 was the only one having the hissy fit.
On Reddit some people were fixing this problem with a "ground loop isolator". It's basically this little noise filter device that plugs in the audio jack. Maybe $15 on Amazon. Anyways, I was about to order one, but before that I decided to take the head unit out of my car to see if any wires were loose. No wires were loose, but what I did find was an alternative 3.5mm jack in the back of my stereo. I'm sure not all stereos have a second port, but there's a decent chance. My particular head unit isn't what you'd call fancy by any means and it has one. So I plugged it in the back 3.5mm port and wouldn't you know, crystal clear sound!! I was so happy when it worked! Now instead of putting my stereo to "auxiliary" for the front port. I have to put it on "bt audio" to access the rear one. (whatever bt audio means, who knows, but it works).
So that's basically it, find out if your car stereo has a secondary 3.5mm port in the back and give it a shot. I didn't realize it at first, but right next to the front auxiliary port it actually says dual auxiliary/audio port. It could be an easy way to find out. As for rerouting the cord. I have a little pocket directly under my radio. There was a tiny hole in the back of the pocket/tray that I put the wire through. It looks cleaner than having it stick out from the faceplate of the radio any way.
If your stereo doesn't have a second 3.5mm port in the back You may want to check out a "ground loop isolator" from Amazon.
Good luck folks. Peace.
Not sure if could post links to the isolator. I'll give it a try.
Kresk - Here is the part that will boggle your mind with this issue. Go and play the stock LG sound file on the phone (The "High Quality" audio track). Once that plays, the static stops. Then switch to your regular music app - I use Spotify - and the music plays static free until the built in music app closes in the background. Then all the static comes back. If there was some way to force the phone to stay in whatever mode it uses for the High Quality audio track, it could be a great fix.
I've also found that there are three different "modes" of static I get on my phone too
1) Static Free
2) Low level of background static, volume independent (volume stays the same low background noise)
3) High level of static, volume dependent (Higher the volume, more static)
Typically when I do the thing where I get it into High Quality audio mode or whatever its using, I get 2 when immediately switching to Spotify. If I lock and unlock my screen, it goes to 3.
I'm going to go and try to plug into the "BT Audio" port on the back of my JVC head unit and see if it works. Will report back on it. I also have a ground loop isolator coming in the mail tomorrow, so I can give an update on that as well.
~PubstarHero
You might need a Ground Loop Noise Isolator, such as this: https://www.amazon.com/Mpow-Ground-Isolator-System-Stereo/dp/B019393MV2
I am thinking of getting one for an issue similar, but not the same as yours.
Same issues, in general. Static on most aux cables, and in my case some headphones don't work at all. My higher-end earbuds work flawlessly though, so go figure. Not sure what to do about it other than the ground fault isolator, though I was about to start looking into a Bluetooth-to-aux module.