I noticed a lot of people want a fast charger for the Note. This charger is for the Touchpad. I have this and it works really well. It charges faster than the OEM charger that came with the Note.
Not to mention, it is on sale right now for less than $5. Go grab one. From past experience, I used this at 15% battery life and charged for an hour and I was back over to 80%.:victory:
http://www.shopping.hp.com/en_US/ho.../FB341AA?HP-TouchPad-Power-Charger&aoid=35252
Is the usb cable that comes with it the same as the note takes?they don't show a pic of the other end and is it a charge only cable?If yes and yes I'm a gonna get one.Thanks
technut said:
Is the usb cable that comes with it the same as the note takes?they don't show a pic of the other end and is it a charge only cable?If yes and yes I'm a gonna get one.Thanks
Click to expand...
Click to collapse
Yes, it is a micro USB cable. One end is USB and other is micro USB. The cable length is longer than most phone cables. I haven't measured it, but from my plug to my desk, I still have excess cable compared to the original one from the phone.
Thank you, getting one!
This have been discussed hundreds time before....
That 1amp is the output of the charger which forwards the current to kernel of the device... NOTE can only intake 1 amp current... ( remove your battery and read the dam sticker :thumbup
Even though you will supply 2 3 4 5 amp... The maximum in would be 1 amp ONLY...
SECONDLY, micro usb cables have a restriction of carrying current... They cannot pass more than 1 amp current successfully... Therefore galaxy tab series does not come with micro usb slots....
Lastly my recommendation would be NOT to waste money on any other chargers...
Noted by the BEAST!!
dx.varun said:
This have been discussed hundreds time before....
That 1amp is the output of the charger which forwards the current to kernel of the device... NOTE can only intake 1 amp current... ( remove your battery and read the dam sticker :thumbup
Even though you will supply 2 3 4 5 amp... The maximum in would be 1 amp ONLY...
SECONDLY, micro usb cables have a restriction of carrying current... They cannot pass more than 1 amp current successfully... Therefore galaxy tab series does not come with micro usb slots....
Lastly my recommendation would be NOT to waste money on any other chargers...
Noted by the BEAST!!
Click to expand...
Click to collapse
It has been discussed, but it DOES charge faster than a conventional 1amp charger. If you don't have the charger and have nothing to compare with, then I don't think you can say it does not work.
Go check FCC about the charge. Also, the cables provided DOES carry a 2amp charge. Our note can handle fast charging but throttles down to a slower charging rate after 80%.
having a micro usb slot or not have a micro usb slot has nothing to do with the current it can handle.
Ipads and Iphones have the same connector but yet one has a 1amp charger and the other a 2amp charger.
deliriousbb said:
It has been discussed, but it DOES charge faster than a conventional 1amp charger. If you don't have the charger and have nothing to compare with, then I don't think you can say it does not work.
Go check FCC about the charge. Also, the cables provided DOES carry a 2amp charge. Our note can handle fast charging but throttles down to a slower charging rate after 80%.
having a micro usb slot or not have a micro usb slot has nothing to do with the current it can handle.
Ipads and Iphones have the same connector but yet one has a 1amp charger and the other a 2amp charger.
Click to expand...
Click to collapse
Firstly, I have tried to use with a 2amp charger that came with my SGT P1000.. NO DIFFERENCE...
SECONDLY, PULL OUT BATTERY AND READ!
Google for micro usb cable max output... You will get your answers...
Noted by the BEAST!!
dx.varun said:
This have been discussed hundreds time before....
That 1amp is the output of the charger which forwards the current to kernel of the device... NOTE can only intake 1 amp current... ( remove your battery and read the dam sticker :thumbup
Even though you will supply 2 3 4 5 amp... The maximum in would be 1 amp ONLY...
SECONDLY, micro usb cables have a restriction of carrying current... They cannot pass more than 1 amp current successfully... Therefore galaxy tab series does not come with micro usb slots....
Lastly my recommendation would be NOT to waste money on any other chargers...
Noted by the BEAST!!
Click to expand...
Click to collapse
deliriousbb said:
It has been discussed, but it DOES charge faster than a conventional 1amp charger. If you don't have the charger and have nothing to compare with, then I don't think you can say it does not work.
Go check FCC about the charge. Also, the cables provided DOES carry a 2amp charge. Our note can handle fast charging but throttles down to a slower charging rate after 80%.
having a micro usb slot or not have a micro usb slot has nothing to do with the current it can handle.
Ipads and Iphones have the same connector but yet one has a 1amp charger and the other a 2amp charger.
Click to expand...
Click to collapse
Well its $5, which is not worth this discussion, I'll gladly give this money even for the stock samsung charger.
i_max2k2 said:
Well its $5, which is not worth this discussion, I'll gladly give this money even for the stock samsung charger.
Click to expand...
Click to collapse
Agreed! A good charger for cheap.
dx.varun said:
Firstly, I have tried to use with a 2amp charger that came with my SGT P1000.. NO DIFFERENCE...
SECONDLY, PULL OUT BATTERY AND READ!
Google for micro usb cable max output... You will get your answers...
Noted by the BEAST!!
Click to expand...
Click to collapse
You don't have to get your panties in a twist. Rather than just read forums and assume the worst of everything try it for yourself. I've tried both and it is faster. Just trying to help my fellow Note users to get the best out of their phones.
btw, what are you screaming about pull out the battery and read? you tell me what you want us to know. RATED: 3.7V; 1500mA... WOW ok that proves your point...sigh:silly:
dx.varun said:
This have been discussed hundreds time before....
That 1amp is the output of the charger which forwards the current to kernel of the device... NOTE can only intake 1 amp current... ( remove your battery and read the dam sticker :thumbup
Even though you will supply 2 3 4 5 amp... The maximum in would be 1 amp ONLY...
SECONDLY, micro usb cables have a restriction of carrying current... They cannot pass more than 1 amp current successfully... Therefore galaxy tab series does not come with micro usb slots....
Lastly my recommendation would be NOT to waste money on any other chargers...
Noted by the BEAST!!
Click to expand...
Click to collapse
As an HP TouchPad owner, I can confirm that the cable provided with the charger are 'special'. My TP will not charge with any other MicroUSB cable connected to the official charger, the same cables which won't charge the TP will charge the Note. (I also own the HP touchstone dock, which the TP spends most of it's life sitting on.)
deliriousbb said:
It has been discussed, but it DOES charge faster than a conventional 1amp charger.
Click to expand...
Click to collapse
I have four different wall chargers, including two of this HP barrel adapter (one that came with the TouchPad, one that came with the Touchstone). With the supplied cable, it does charge the TouchPad very quickly. From webOS, the net charge rate is about 1.6 A with the screen on, so probably close to 2 A coming out the USB port.
However, when you plug a Note into this charger, the Note will still only draw 1 A. I have other AC chargers that are also able to supply 1 A to the Note, so in that respect this HP charger isn't anything special. However, it is only $5, which is a good deal.
---------- Post added at 11:39 PM ---------- Previous post was at 11:14 PM ----------
pTeronaut said:
My TP will not charge with any other MicroUSB cable connected to the official charger, the same cables which won't charge the TP will charge the Note.
Click to expand...
Click to collapse
I've found that the microUSB cable that comes with the Note, when paired with the HP TouchPad's AC charger, will supply 2 A. At least, that's what the OS reports: /sys/devices/platform/usb_gadget/current-mA shows "2000". Plugging the TouchPad into the Note's AC charger shows a value of "900". Plugging it into my laptop's USB port drops that value down to "500", as expected.
I bought two a week ago off Amazon for $10 each. $5 each with free shipping is a steal. I picked up three more. Thanks for posting this deal. I get 1A charging with either the stock charger or TP charger. I like to have a few extra chargers to sprinkle around at home or work (for my Note and the other devices I own that charge off USB.... including a TP).
deliriousbb said:
Yes, it is a micro USB cable. One end is USB and other is micro USB. The cable length is longer than most phone cables. I haven't measured it, but from my plug to my desk, I still have excess cable compared to the original one from the phone.
Click to expand...
Click to collapse
When you charge your phone using this HP microUSB cable, do you have issue with NO DEEP SLEEP when unplugging the Note from the charger?
There has been issues reported in XDA where, depending on the USB cables used to charge the Note (connected to computer OR power charger), if you unplug the Note, it will not go DEEP SLEEP, causing significant power drain.
This does NOT happen when the Note is charged using the cable that came with the Note.
Download Current Widget from the play store. Add widget to home screen and you will realize that your phone is not charging any more than 1 amp as designed.
Try the usb out from your pc and you will see about half an amp.
Sent from my SAMSUNG-SGH-I717 using xda premium
I have the galaxy tab brick charger the HP touch pad charger and my note charging brick....the touchpad charger works faster...but I feel like it doesn't get fully charged..seems to die faster?. I used the galaxy tab brick...slow to charge warms my phone up nicely...I'd stick with the original note charger.
Sent from my SAMSUNG-SGH-I717 using xda premium
lanwarrior said:
When you charge your phone using this HP microUSB cable, do you have issue with NO DEEP SLEEP when unplugging the Note from the charger?
There has been issues reported in XDA where, depending on the USB cables used to charge the Note (connected to computer OR power charger), if you unplug the Note, it will not go DEEP SLEEP, causing significant power drain.
This does NOT happen when the Note is charged using the cable that came with the Note.
Click to expand...
Click to collapse
I charge my Note overnight using my Touchpad's MicroUSB cable plugged into the Samsung charger, and I don't experience any difference in power drain.
Where is that post from the guy who put all these petty arguments to rest with scientific tests of all the various options and results??
Good lord people it's a charger for a phone .. no need to get so heated!
(unlike my stock charger.. which gets very heated!)
great price!!!
ordered 3 of them
the price is way cheaper than just a single micro usb cable shipped from other stores
i have 3 already
1 at work, 2 for home.
definitely faster than OEM. I charge overnight, no issues. had for around 5-6 months now. and i can use the phone while charging.
fact is that it DOES charge faster.
i recommend it
WOW***
Great price I bought 2!
Related
will the included USB cable that comes with the Note be able to charge the phone in my car if i plug it into lets say my iPhone auto adapter which has a usb port on it?
ARTAQaf said:
will the included USB cable that comes with the Note be able to charge the phone in my car if i plug it into lets say my iPhone auto adapter which has a usb port on it?
Click to expand...
Click to collapse
You will be charged at much slower rate (limited to 500ma max), or not at all if your phone battery is almost dead. iPhone chargers are designed for iPhone only. You will need a Samsung auto charger (some other non-iPhone smartphone chargers may work too, just not iPhone chargers).
I just bought a cheap 5$ car charger USB adapter for the note will it work?
corey_r said:
I just bought a cheap 5$ car charger USB adapter for the note will it work?
Click to expand...
Click to collapse
It will definitely work. The question with those cheap ones is, how long will it last. I usually try to find an OEM branded one like this:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250973439590#ht_2859wt_1000
Typically, chargers with USB port on it will only do slow charge. In order to support fast charge, you will need short out the data pins to allow phone to draw more than 500ma. Typically auto-chargers that comes with microUSB plug directly, such as the Samsung auto charger, will do so, asume your charger is rated to output more than 500ma.
ARTAQaf said:
will the included USB cable that comes with the Note be able to charge the phone in my car if i plug it into lets say my iPhone auto adapter which has a usb port on it?
Click to expand...
Click to collapse
It will be able to charge it. Keep in mind IF your iPhone USB charger max current output (5V 1000mA) is LESS than the Note's charger output, it will take longer to fully charge - but it will charge and will NOT damage the phone.
If you're looking to buy a new usb charger, look for one with the highest mA output rating since whatever device you plug into it will only draw what it needs. ie, my iPad charger is rated @ 2A/2000mA so it covers every device I own (all rated for different current inputs from 500mA up to 2000mA) and that's the only usb charger I take when I travel since I just have to switch out cables to charge other devices. On the other hand, if I only had a lower current rating usb charger, my iPad (requires 2000mA) would be out of luck.
Current output info can be found on the respective charger of your favorite device.
Hope that helps.
it does help, thanx Rand! i cancelled my Amazon order...wish i saw this post sooner.
I have this works great with anything up to 2.1amps...
http://www.bestbuy.com/site/Belkin+...&ref=06&loc=01&ci_src=14110944&ci_sku=1232905
I just bought this
Man I wish I saw this an hour ago I just bought this you think it's ok?http://www.ebay.com/itm/280818054928?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649:confused:
JGuinan007 said:
Man I wish I saw this an hour ago I just bought this you think it's ok?http://www.ebay.com/itm/280818054928?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649:confused:
Click to expand...
Click to collapse
Looks like that charger is rated @ 700mA. It'll charge the note about 30% slower than the wall charger.
This is my car charger
http://www.proclipusa.com/brodit-de...ord-for-fixed-installation--513303-18842.aspx
poop i couldn't cancel my amazon order. well i 'm sure i'll still use it.
Alot has been said about the quality of various batteries that we are all looking at for our devices...however very little about the different chargers that are out there.
I thought my charger that I bought was defective cause I let it charge overnight and it wasn't fully charged. That is not the case.
The Charger that the Note comes with charges at 1A. Most of these external battery only chargers charge at 350mA.
Take a look at this calculator:
http://www.csgnetwork.com/batterychgcalc.html
Using the link to the calculator above, you should expect a 2600mAh battery to fully charge using one of these cheap chargers in about 9 HOURS!! The charger that the note comes with should expect about 3.4 hours. That's a huge difference in charge time!!
So be sure to take a look at the output of these chargers before you get too excited and purchase one. If it takes you 24 hours to charge a battery, what good is it to you?
Thanks for the battery reference URL.
This is basically another scenario of 'you get what you pay for..'
It seems to often apply to batteries and chargers.
Whereas for like cases, you have a better chance of actually saving money and getting quality at the same time.
CradleRob said:
Alot has been said about the quality of various batteries that we are all looking at for our devices...however very little about the different chargers that are out there.
I thought my charger that I bought was defective cause I let it charge overnight and it wasn't fully charged. That is not the case.
The Charger that the Note comes with charges at 1A. Most of these external battery only chargers charge at 350mA.
Take a look at this calculator:
http://www.csgnetwork.com/batterychgcalc.html
Using the link to the calculator above, you should expect a 2600mAh battery to fully charge using one of these cheap chargers in about 9 HOURS!! The charger that the note comes with should expect about 3.4 hours. That's a huge difference in charge time!!
So be sure to take a look at the output of these chargers before you get too excited and purchase one. If it takes you 24 hours to charge a battery, what good is it to you?
Click to expand...
Click to collapse
So I guess for battery longevity, you should use a 500 mA charger (the typical USB output). That way it doesn't charge it too quick (and overheat the battery).
SPtheALIEN said:
So I guess for battery longevity, you should use a 500 mA charger (the typical USB output). That way it doesn't charge it too quick (and overheat the battery).
Click to expand...
Click to collapse
No, actually. Lithium ion batteries, unlike nickle-cadium batteries actually perform and last better with short, fast charges. Android's battery stats are helped by a few full cycles, but it is not better for the battery to full cycle or slow charge.
Sent from my SAMSUNG-SGH-I717 using xda premium
Thank you for this information, very helpful as I have other phone chargers. Is there a way(Windows based utility) to tell how many mah a USB port is outputting while charging?
lmike6453 said:
Thank you for this information, very helpful as I have other phone chargers. Is there a way(Windows based utility) to tell how many mah a USB port is outputting while charging?
Click to expand...
Click to collapse
A multimeter
Sent from my SGH-I717R using xda premium
lmike6453 said:
Thank you for this information, very helpful as I have other phone chargers. Is there a way(Windows based utility) to tell how many mah a USB port is outputting while charging?
Click to expand...
Click to collapse
*I am not an electrical expert, I just play one on TV.*
There are standards for USB outs. Just Google the standard. That said, there is USB1, USB2, and now USB3. Check your motherboard to see which one you have. There is also a newish thing on motherboards that will do a rapid charge by changing a setting on the BIOS. That's what i got off the top of my head. Do a little research.
As was pointed out on another thread, the Note looks for a low resistance/short between pins 2 and 3 of the USB cable. If it sees the low resistance, it enables a high current charge; otherwise, it sticks with USB standard charge of less than 500 ma. The 2/3 pin setup is not true of USB connections to a computer. The Note power adapter is set up this way to do a fast charge. Most chargers and portable battery chargers leave pins 2 and 3 unconnected, so they will not fast charge a Note even if they can supply 1A.
I purchased a Scosche 5000 mah battery with USB ports for charging Ipads, Iphones, and other devices. It also charges a Galaxy Tab with a special USB adapter plug. I tried the Tab adapter with my new Note and it was charging at 5 percent charged every ten minutes or so. Without the USB adapter, the Note charged at 2 percent every ten minutes or so. Without the adapter, the Note displays an MTP initialization notification. With the adapter, there is no MTP notification.
The Scosche battery is a big improvement over older Trent 5000 mah batteries. There is a push button to turn the Scosche battery on. The battery will turn off if no device is attached or it the device is fully charged. One of the ports can output 2.1A for an Ipad. The Trent battery would run down if it was left on.
Staples carries the Scosche battery for $80. I used a $29 online coupon from Staples that expires 3/5/2012.
I did not see anywhere on the Scosche website where they sell the Tab adapter by itself.
Ipaqman01 said:
As was pointed out on another thread, the Note looks for a low resistance/short between pins 2 and 3 of the USB cable. If it sees the low resistance, it enables a high current charge; otherwise, it sticks with USB standard charge of less than 500 ma. The 2/3 pin setup is not true of USB connections to a computer. The Note power adapter is set up this way to do a fast charge. Most chargers and portable battery chargers leave pins 2 and 3 unconnected, so they will not fast charge a Note even if they can supply 1A.
I purchased a Scosche 5000 mah battery with USB ports for charging Ipads, Iphones, and other devices. It also charges a Galaxy Tab with a special USB adapter plug. I tried the Tab adapter with my new Note and it was charging at 5 percent charged every ten minutes or so. Without the USB adapter, the Note charged at 2 percent every ten minutes or so. Without the adapter, the Note displays an MTP initialization notification. With the adapter, there is no MTP notification.
The Scosche battery is a big improvement over older Trent 5000 mah batteries. There is a push button to turn the Scosche battery on. The battery will turn off if no device is attached or it the device is fully charged. One of the ports can output 2.1A for an Ipad. The Trent battery would run down if it was left on.
Staples carries the Scosche battery for $80. I used a $29 online coupon from Staples that expires 3/5/2012.
I did not see anywhere on the Scosche website where they sell the Tab adapter by itself.
Click to expand...
Click to collapse
Do you have a model number on that USB adapter? Maybe in the instructions?
There is only the name Scosche on the adapter. The guide only calls it the Galaxy Tab adapter.
Sent from my SAMSUNG-SGH-I717 using Tapatalk
Ipaqman01 said:
As was pointed out on another thread, the Note looks for a low resistance/short between pins 2 and 3 of the USB cable. If it sees the low resistance, it enables a high current charge; otherwise, it sticks with USB standard charge of less than 500 ma. The 2/3 pin setup is not true of USB connections to a computer. The Note power adapter is set up this way to do a fast charge. Most chargers and portable battery chargers leave pins 2 and 3 unconnected, so they will not fast charge a Note even if they can supply 1A.
I purchased a Scosche 5000 mah battery with USB ports for charging Ipads, Iphones, and other devices. It also charges a Galaxy Tab with a special USB adapter plug. I tried the Tab adapter with my new Note and it was charging at 5 percent charged every ten minutes or so. Without the USB adapter, the Note charged at 2 percent every ten minutes or so. Without the adapter, the Note displays an MTP initialization notification. With the adapter, there is no MTP notification.
The Scosche battery is a big improvement over older Trent 5000 mah batteries. There is a push button to turn the Scosche battery on. The battery will turn off if no device is attached or it the device is fully charged. One of the ports can output 2.1A for an Ipad. The Trent battery would run down if it was left on.
Staples carries the Scosche battery for $80. I used a $29 online coupon from Staples that expires 3/5/2012.
I did not see anywhere on the Scosche website where they sell the Tab adapter by itself.
Click to expand...
Click to collapse
What does an "MTP initialization notification" look like on the Note? How do I identify it?
If I don't see it when charging, does that mean it's getting a fast charge for sure, or just that it might be?
lastdeadmouse said:
A multimeter
Sent from my SGH-I717R using xda premium
Click to expand...
Click to collapse
How exactly would you use a multimeter to do this? From what I've seen, they have two contacts -- where would you stick those? Or is there some kind of micro USB conversion thingy to use with a multimeter?
capite said:
How exactly would you use a multimeter to do this? From what I've seen, they have two contacts -- where would you stick those? Or is there some kind of micro USB conversion thingy to use with a multimeter?
Click to expand...
Click to collapse
Cut a USB cable, and strip a portion of the power wires. Set the multimeter to a 10A DC current scale (assuming it supports 10A, but most craftsman and up do, with common and a 10A lead), disconnect the plug, attach common to negative wire and positive to positive wire, gator clips or something, then plug it in and read it. The current support and time it can be on depends on the multimeter. Mine does up to 10A for Max 30 sec.
Sent from my SGH-I717R
So my charger met with an untimely demise. I am unable to get my hands on a replacement one at the moment.
I am currently using my computer's USB port which as you will know doesn't give quite enough juice. I have seen a microusb charger with 5V and 2A. Will this do a job (and also not get rid of the message that i am drawing more juice than the battery is getting)?
I use the charger that came with my Evo 4g. It needs to sit overnight, but it charges to green.
milomak said:
So my charger met with an untimely demise. I am unable to get my hands on a replacement one at the moment.
I am currently using my computer's USB port which as you will know doesn't give quite enough juice. I have seen a microusb charger with 5V and 2A. Will this do a job (and also not get rid of the message that i am drawing more juice than the battery is getting)?
Click to expand...
Click to collapse
No.
The reason for the strange shape USB lead HTC have is that it gives 9V and 1.7A - 5V isn't going to cut it, it will charge but ever so slowly and if you try to charge whilst using it you'll probably find it doesn't, it just discharges more slowly.
If I were to take an old wall wart I have here that is 9V and 2A and wire a standard micro USB cable to it, would that work to charge my flyer quickly? In other words is the strange connector necessary or just the 9V and 2A?
Sent from my PG41200 using Xparent Purple Tapatalk 2
bsoplinger said:
If I were to take an old wall wart I have here that is 9V and 2A and wire a standard micro USB cable to it, would that work to charge my flyer quickly? In other words is the strange connector necessary or just the 9V and 2A?
Sent from my PG41200 using Xparent Purple Tapatalk 2
Click to expand...
Click to collapse
NO, because the fast charge requires the special connector on the HTC power cord , a micro-usb will not allow the Flyer to draw the high current.
DigitalMD said:
NO, because the fast charge requires the special connector on the HTC power cord , a micro-usb will not allow the Flyer to draw the high current.
Click to expand...
Click to collapse
so an adaptor with a usb slot and using the usb cable would work?
milomak said:
so an adaptor with a usb slot and using the usb cable would work?
Click to expand...
Click to collapse
If you're using the HTC-specific microUSB cable, the adaptor would have to provide the correct amount of power (9V and 1.7A). Most usb power adaptors do not provide the adequate amount. A little while back, I made the mistake of taking just my phone usb adaptor to charge everything on a trip out of the country for nearly two months. It worked great for everything except for my View. Even though I had the HTC-specific usb cable for the View, it was still like charging via a computer usb port. It would get the job done if I left it all day or all night, but it took forever to charge.
I really would try to track down an OEM charger. Even if you find a usb adaptor that puts out the right amount of power, it still might not provide the short amount of charging time that the OEM charger does. It should theoretically, but many users have had charging time woes when using anything but the OEM charger.
DigitalMD said:
NO, because the fast charge requires the special connector on the HTC power cord , a micro-usb will not allow the Flyer to draw the high current.
Click to expand...
Click to collapse
No it doesn't. A member of my site took the OEM charger, wired a 90 degree micro USB port to it, charges at full speed.
Sent from my Transformer TF101 using Tapatalk 2
Volts and Amps - PowerFlask
From the posts on this subject it seems that the Powerflask 13000 mAh powerbank I bought today and which charges at 5.3 volt with a 1amp and 2.5 amp port won't properly charge my flyer?
Can I safely use the 2.5amp port or should I rather stick to the 1amp port.
Any advice would be much appreciated.
Thanks
Maffs,
Maffs said:
From the posts on this subject it seems that the Powerflask 13000 mAh powerbank I bought today and which charges at 5.3 volt with a 1amp and 2.5 amp port won't properly charge my flyer?
Can I safely use the 2.5amp port or should I rather stick to the 1amp port.
Any advice would be much appreciated.
Click to expand...
Click to collapse
Folks on here have mentioned that the device (and other tablet/smartphone devices) will only draw the amount of current (amps) it needs. So using a charger with a higher amp rating is not a concern (in theory).
But I think others have debated this, and even made claims of higher volt/amp rated chargers damaging their devices (however anecdotal).
In any case, from the responses on this thread, it appears that any charger that doesn't have HTC's proprietary connector that they used for the Flyer, will charge the tablet very slowly. I just plugged my Flyer into a microUSB charger the other day (just got back from a trip, and my stock charger was still packed), and it charged extremely slowly. It was slower than I remembered it being. It was plugged in for maybe 4 hours, and only increased the charge by 10 or 15%.
PowerFlask Volts and Amps
Thanks for the feedback, much appreciated.
I ran a quick test and connected the Flyer to the battery pack.
The flyer charged from 76% to 84% in 30 minutes . I realise that such a short charge isn't a proper test but it looks promising.
I used the 1amp port and will as you cautioned avoid the 2.5 amp port.
Maffs
When ever I drive, I have my phone hooked up to my Escort Red Line radar detector and my car's stereo via bluetooth (both). In order for me to use the radar detector effective, I need to have GPS and Blueooth enabled. This is a HUGE SUPER OMG battery drainer for my amaze. 20 minutes drive kills about 35% of the phone's power. My radar detector offers a slot to charge my phone BUT it still drains, not enough juice flowing in. Someone said it is because it's probably a .5amp.
So I am running a extension from the 12v lighter that's in the trunk to the front of my car. Amazon has a generic 2.1amp for 3 bucks.
http://www.amazon.com/Premium-Heavy...121&sr=8-1&keywords=htc+amaze+car+charger+amp
But on ebay, I found the original HTC car charger for 15 bucks which is a 1amp.
http://www.ebay.com/itm/HTC-Amaze-4...918506?pt=PDA_Accessories&hash=item27c867022a
What do you guys recommend? My logic says go for the 2.1amp, the phone will draw as much as it needs from it.
The 1amp.
Anything higher you'll damage the phone or the battery.
A wall plug power supply or a usb supply is 5.0v/1amp.
The 2.1 amp is probably 1 amp per port. Although it does not seem to specify.
F9zSlavik said:
What do you guys recommend? My logic says go for the 2.1amp, the phone will draw as much as it needs from it.
Click to expand...
Click to collapse
Right!:good:
---------- Post added at 09:23 AM ---------- Previous post was at 08:41 AM ----------
soundping said:
The 1amp.
Anything higher you'll damage the phone or the battery.
A wall plug power supply or a usb supply is 5.0v/1amp.
Click to expand...
Click to collapse
That means a higher capacity battery (more current NOT MORE VOLTAGE) will damage the phone?!!!!
Totally wrong!
A higher current will not damage the phone. A higher voltage will do it!
Please do not mix the current with voltage!
Voltage is same 5 Volts (±5%) for these “USB like” applications (1A or 2.1A power supply our case )They use USB socket/connector but usually only pin 1 and 4 (+ and-)
Regular computer USB port can supply max 0.5-0.9 A depending on version.
For battery charging devices the current can go to 5A.
Higher voltage will trip a warning window telling you to disconnect and use official HTC equipment.
The phone monitors input voltage to protect the equipment.
nyc_tdi said:
That means a higher capacity battery (more current NOT MORE VOLTAGE) will damage the phone?!!!!
Totally wrong!
A higher current will not damage the phone. A higher voltage will do it!
Please do not mix the current with voltage!
Voltage is same 5 Volts (±5%) for these “USB like” applications (1A or 2.1A power supply our case )They use USB socket/connector but usually only pin 1 and 4 (+ and-)
Regular computer USB port can supply max 0.5-0.9 A depending on version.
For battery charging devices the current can go to 5A.
Click to expand...
Click to collapse
and to add to that... unless you take the charger apart and short pins 2 and 3, it will only ever draw 500mA, as it assumes that it is hooked up to a regular powered USB port... I have bought multiple car charger usb adapters, and I have taken all of them apart and soldered the 2nd and 3rd pins together... otherwise charge time = forever, and sometimes it won't even charge if you have wifi or data/gps/bluetooth all going at once...
I recently got an Amaze and am generally happy with it. The biggest problem I have right now is finding the right car charger for it because the car charger I previously used (a 1A monoprice car charger) doesn't give it enough charge. I have been reading through the forums and some has been saying that if the charger is not working properly, it will recognize it as charging via USB rather than AC. In my case, the phone seems to be reading it as charging through AC, but there still doesn't seem to be enough current going through it. The phone will only charge if NOTHING is going on (i.e. screen's off, no GPS, etc.). I've been using CoPilot GPS and it draws the battery like crazy. Anyone has any idea as to which car charger would work properly with the Amaze such that I'll be able to charge (or at least maintain the charge) while using it as a GPS? Do I need to go up to a 2.1A charger?
I would look for a 4-5 star rated 2.1a car charger on Amazon.
Just read through the comments and feedback and you'll find one that's right for you.
I prefer the USB charger base itself and then using the OEM cable that came with the Amaze.
It seems to charge faster with that cable, at least to me anyway.
Remember though if it's rated 2.1a but has two USB slots that 2.1a will be cut in half if used to charge two different devices.
Hope this helps.
I couldve sworn we talked about this months ago. Let me see if I can find the thread.
nguyendqh said:
I would look for a 4-5 star rated 2.1a car charger on Amazon.
Just read through the comments and feedback and you'll find one that's right for you.
I prefer the USB charger base itself and then using the OEM cable that came with the Amaze.
It seems to charge faster with that cable, at least to me anyway.
Remember though if it's rated 2.1a but has two USB slots that 2.1a will be cut in half if used to charge two different devices.
Hope this helps.
Click to expand...
Click to collapse
you won't get the full 2.1a unless you usee a charge only cable or modify the charger as I stated above...
I ended up getting a 2.1A car charger and a USB charge only cable, and it's working perfectly. When I have the screen on full brightness and doing navigation with Co-Pilot GPS, my phone's no longer losing charge and is actually charging. The combo also works with my tablet as well.
blast0id said:
and to add to that... unless you take the charger apart and short pins 2 and 3, it will only ever draw 500mA, as it assumes that it is hooked up to a regular powered USB port... I have bought multiple car charger usb adapters, and I have taken all of them apart and soldered the 2nd and 3rd pins together... otherwise charge time = forever, and sometimes it won't even charge if you have wifi or data/gps/bluetooth all going at once...
Click to expand...
Click to collapse
This is damn helpful! So THAT is why when driving and using gps or whatnot I would always lose more battery even on charger.. So basically I can just solder the middle 2 pins together to trick it into thinking it is being powered like a home charger? No chance it will hurt anything I assume?
Silentbtdeadly said:
This is damn helpful! So THAT is why when driving and using gps or whatnot I would always lose more battery even on charger.. So basically I can just solder the middle 2 pins together to trick it into thinking it is being powered like a home charger? No chance it will hurt anything I assume?
Click to expand...
Click to collapse
I have done this to every single one of my USB car chargers... not a single issue...
Since I got my note 3 I've been charging it with my old AC chargers I bought on ebay which is a generic micro-usb charger (I got a couple of them laying around the appartment). I use my old chargers often because the samsung USB cable which was provided with the phone is always pluged into my desktop computer, and I didn't want to go trough the hassle of moving the cable all around the house to charge my phone.
Well anyway, so far I've notice charging times were pretty long(6-8hours), but I shrugged it off because I simply thought a bigger battery require longer to charge. But this weekend I slept off at my in-laws and I brought my samsung cable and AC adapter. I looked up with better battery stats and notice the charge time was around 3times as fast. (2hours or so for a 100% charge). Dammmn!
So why am I getting long charges with my ebay chargers?
Is it because they are cheap china product?
Is it because they don't have the USB3.0 port?
I'm thinking the USB3.0 has nothing to do with charging times if it's pluged with an AC adapter right? So my long charge time must be because of cheap products? Ok then, but if I want to buy additional chargers, or even a cradle for my bedside table. How can I know if they will have the best charge time? Am I forced to buy samsung branded stuff just to make sure?
Cause I'd be interested in something like this :
http://www.ebay.ca/itm/For-Samsung-Galaxy-Note-2-3-Cradle-Sync-Dock-Mode-2-1-amp-Otterbox-Fits-/251362752408?pt=US_Cell_Phone_PDA_Chargers&hash=item3a86633798&_uhb=1
but I'm not gonna buy it if it takes double/triple charging time..
Patbach said:
Since I got my note 3 I've been charging it with my old AC chargers I bought on ebay which is a generic micro-usb charger (I got a couple of them laying around the appartment).
Click to expand...
Click to collapse
The Note 3 should charge in just over two hours with either USB 2 or 3 cables. If you download https://play.google.com/store/apps/details?id=com.abmantis.galaxychargingcurrent.free&hl=en that will tell you the charging current. It should be 1200mA with the screen on and 1800mA with it off (trick is turn the screen off for 10s then back on and refresh and you should see 1800mA).
As long as the charger can deliver 1800mA and you are using a decent quality cable that should be all you need. Plugged into a USB port you'll only see 450mA on either USB 2 or 3.
Usually the ones that charge this quickly have an output of 2 amps. That is the output of the charger that came with the phone.
Sent from my Verizon Samsung Galaxy Note III.
Prevous Owner/Hacker of... numerous other devices!
CraigAmey said:
The Note 3 should charge in just over two hours with either USB 2 or 3 cables. If you download https://play.google.com/store/apps/details?id=com.abmantis.galaxychargingcurrent.free&hl=en that will tell you the charging current. It should be 1200mA with the screen on and 1800mA with it off (trick is turn the screen off for 10s then back on and refresh and you should see 1800mA).
As long as the charger can deliver 1800mA and you are using a decent quality cable that should be all you need. Plugged into a USB port you'll only see 450mA on either USB 2 or 3.
Click to expand...
Click to collapse
wow thanks there lots of useful stuff