Anyone else having a problem with tablet not showing up on computer after ICS. Updated the tablet with Allinone version 4 without any problem but now i need to shift some pictures onto the computer. When i plug in the tablet nothing happens on either the pc or the tablet. Ive used 2 different cables and used 2 different computers but nothing shows up. Debug is on. As far as im aware this has only happened after the ICS rooted update.
I thought that by transferring the pictures over to the sd card would at least sort that out but now i read and tried that external card is being read as "read only". So cant transfer the pictures to sd card and computer not recognising the tablet, now what?
Any advise?
D.
diddy64 said:
Anyone else having a problem with tablet not showing up on computer after ICS. Updated the tablet with Allinone version 4 without any problem but now i need to shift some pictures onto the computer. When i plug in the tablet nothing happens on either the pc or the tablet. Ive used 2 different cables and used 2 different computers but nothing shows up. Debug is on. As far as im aware this has only happened after the ICS rooted update. I thought that by transferring the pictures over to the sd card would at least sort that out but now i read and tried that external card is being read as "read only". So cant transfer the pictures to sd card and computer not recognising the tablet, now what?
Any advise?
D.
Click to expand...
Click to collapse
Your computer not recognizing your tablet sounds like an ADB driver problem, so you may have to reinstall the drivers. Condi's AIO Tweaks and Mods submenu items 12 and 11 will solve your problems with sdcard and sdcard2 write permissions and USB Mass Storage support so your computer can access your tablet's memory. Searching the forum about these problems will provide you with additional information on how to deal with them as they have been discussed several times.
Thanks for the reply. Its been so long since i initially setup the tablet. Correct me if I am wrong but when the tablet is connected to the computer the tablet should show up as sony s tablet, is that when the drivers need to be installed. Ive a shocking memory. Im starting to panic as ive documents that I have done in collage. Without the sd card transfering data to extenal in knackered.
So, if I plug the tablet in and NOTHING shows up either on tablet or pc, does that mean that the drivers need to be reinstalled?
diddy64 said:
So, if I plug the tablet in and NOTHING shows up either on tablet or pc, does that mean that the drivers need to be reinstalled?
Click to expand...
Click to collapse
Reinstalling the drivers is what other people have had to do to solve the problem you seem to have. For example, read this thread: ADB Issues after ICS update?
Thanks for your time and effort. I have seen this post when i was searchings for answers. Problem is that NOTHING happens when i plug the sony into the computer. Tablet does not acknowledge that debugging is available through the usb even though it is ticked on the tablet. The computer shows nothing either as the tablet has not got into communicating through usb. So to uninstall the drivers will be impossible until the pc recognises the tablet.
diddy64 said:
Thanks for your time and effort. I have seen this post when i was searchings for answers. Problem is that NOTHING happens when i plug the sony into the computer. Tablet does not acknowledge that debugging is available through the usb even though it is ticked on the tablet. The computer shows nothing either as the tablet has not got into communicating through usb. So to uninstall the drivers will be impossible until the pc recognises the tablet.
Click to expand...
Click to collapse
The computer is probably not recognizing or listing the tablet because the device drivers are borked. In Microsoft Windows, you can uninstall unlisted (unrecognized) devices by going into Device Manager, selecting "View" from the standard menu, selecting "Show hidden devices" (which should cause unlisted/unrecognized device names to be listed), then right-clicking on the device's name and selecting "Uninstall". After uninstalling the device, select "Action" from the standard menu, then select "Scan for hardware changes" to cause the computer to detect the tablet and prompt you to install the device drivers.
Related
I don't get a prompt to mount when I connect to my comp. I've searched the menus with no luck. I am really impressed with this rom and think it's just me. help please.
Drag notification bar down and select USB Connected.
Its has nothing in the notificationbar. On my computer it says usb device has malfunctioned. But nothing on my phone its just charging. I have windows xp.no internet on my comp either.
Amazingbman said:
Its has nothing in the notificationbar. On my computer it says usb device has malfunctioned. But nothing on my phone its just charging. I have windows xp.no internet on my comp either.
Click to expand...
Click to collapse
That happened to me once, I restarted my computer and it worked. I would also just tried another USB port after that
I've been having this problem for awhile. I've switched phones, computers
erased my sd. I don't know what the problem is.. Ive even bought a new usb cord. I'm going to buy a new sd card and try that. My computer says it doesn't recognize my phone. All I want is too put music on my card.. It worked so nice before the ota 2.1...i really appreciate your input.
It could be the drivers. See if it gives you the option to uninstall the drivers from Device Manager. Maybe you can add an ADB device. I forget how.
My device isn't recognized by my computer. Is the tablet supposed to prompt me to enable USB storage when it's plugged into a computer?
Nope...For me it just shows up in my computer..a new window doesnt pop up like it regularly does for new items inserted.
win xp didn't worked for me either - win 7 worked without any problems
I guess I'm not clear. When I had a rooted NOOKcolor (replaced stock ROM with a Gingerbread one), on the device itself would be a prompt to enable USB storage when it was plugged into a computer. This would appear in the notification bar at the bottom. Once I clicked yes/ok on the device, only then would it appear on my computer as a storage device. This doesn't happen with the Sony. I'm using a Mac.
So, those with a computer that recognizes the device, are you prompted on the tablet to enable USB storage or does it simply appear on your computer as a storage device with no prompting? Again, I'm not referring to your computer prompting you to do anything. I don't have another Honeycomb tablet to answer my own question. Thanks.
Honeycomb doesn't support USB mass storage. It uses MTP instead so things may work
a bit different than you expect. If you're on a Mac you need to download the Android file transfer program from google.
Sent from my Sony Tablet S using Tapatalk
wallyworld17 said:
Honeycomb doesn't support USB mass storage. It uses MTP instead so things may work
a bit different than you expect. If you're on a Mac you need to download the Android file transfer program from google.
Sent from my Sony Tablet S using Tapatalk
Click to expand...
Click to collapse
Thanks so much for the quick reply! Now I can stop scratching my head in bewilderment. Now I recall reading about Android file transfer program. I think I downloaded it months ago.
Yep, just checked my Downloads folder. It's been sitting here, never installed.
Im so saaad! i think its all my fault.. i copied everything from my galaxy s2 storage over to my new xperia s.. and now it doesnt recognize the phone so i can transfer files..
what should i do ? please help!
btw the phone is just awesome! wauw!
I would also like to know how to properly mount the storage to a PC so that it is recognised as a Mass Storage Device rather than a MTP connection..?
Its so annoying not being able to see thumbnails of the pictures/videos you are trying to access..its also annoying that the PC has to spend time on downloading the files before playing rather than streaming straight from the storage.
Anyone have any ideas? plz..
Rather than starting a new thread I just used this one..thx in advance
When you connect the phone, on notification bar should say Internal storage connected. When you go to My Computer you should see Other section, where new device come up, called... Xperia S. Double click on it, so it goes to Internal storage. Again, double click and... you can see internal content. Hope it helps.
Same thing happened to me.... Today onwards time n again seeing a mtp driver failed issue when connecting to my win7 laptop. It wad working fine earlier. When I switch off n restart the device,it installs driver correctly and autoplay option comes up to open the xperia s device. However when I click on open folder, I dont see any folders in my xperia s phone. Hence no file transfer is possible. How can I get my phone working again?
I tried to do pc system restore... Since it was working yesterday...but that didnt solve the issue either. Any ideas?
Sent from my LT26i using XDA
Do you use different USB ports? Try to stick to only one. I still have XP and mine is always working, so this is definitely PC and windows issue.
I have a Win7 64bit Home Premium edition VAIO.
when I first got the phone, I could use it to connect to PC Companion. It would also show up as a storage device automatically, and using the same I had copied over music and pictures.
However, after 2 days of use, I noticed, my phone was no longer being identified as a device. Also, it gets a Code 10 - Device cannot be started error when I look into the driver details.
I tried to reinstall the MTP driver, but it never gets installed successfully. It always gives a driver failed to install error.code 10.
I can still connect my WD hard disk and other usb devices.
I saw somewhere in the Forum someone had described that I needed to uninstall and reinstall WMP to make this work. Didnt work
I downloaded the Windows DEK to ensure that all the drivers gets reinstalled, that didnt help either.
I also restored my laptop back to factory setting......still no luck with the fresh install.
So, here I am with a phone where I cant connect the device to move in OR out music/pictures etc.
The problems are:
1) MTP driver gives an error while installation. I tried to manually select the MTP USB driver and isntall it. That didnt work either.
2) When I connect SEUS, with the phone restarted by holding the volume button SEUS identifies the phone and shows me that there are no updates. Not sure if SEUS can be used for exploring the phone. Most probably NO.
3) PC companion tries to find the phone. It says it may take few minutes to identify the phone if it has lots of files. After that the operation fails suggesting that PC companion could not find the phone.
I restarted both the phone and my device several times......did not work.
I uninstalled the MTP and USB drivers and restarted and got them reinstalled........didn't work either.
Any idea on what needs to be done?
I have tried all the ports and a different USB cable as well.
I even tried changing settings of the usb port as described in the below link..
Nothing worked
Is it possible to get the Sony specific drivers from somewhere?
Hi has this problem been solved. I have two computers, the win 7 one installed fine but it refuses to work on the xp one.
any help?
intellix said:
I have a Win7 64bit Home Premium edition VAIO.
when I first got the phone, I could use it to connect to PC Companion. It would also show up as a storage device automatically, and using the same I had copied over music and pictures.
However, after 2 days of use, I noticed, my phone was no longer being identified as a device. Also, it gets a Code 10 - Device cannot be started error when I look into the driver details.
I tried to reinstall the MTP driver, but it never gets installed successfully. It always gives a driver failed to install error.code 10.
I can still connect my WD hard disk and other usb devices.
I saw somewhere in the Forum someone had described that I needed to uninstall and reinstall WMP to make this work. Didnt work
I downloaded the Windows DEK to ensure that all the drivers gets reinstalled, that didnt help either.
I also restored my laptop back to factory setting......still no luck with the fresh install.
So, here I am with a phone where I cant connect the device to move in OR out music/pictures etc.
The problems are:
1) MTP driver gives an error while installation. I tried to manually select the MTP USB driver and isntall it. That didnt work either.
2) When I connect SEUS, with the phone restarted by holding the volume button SEUS identifies the phone and shows me that there are no updates. Not sure if SEUS can be used for exploring the phone. Most probably NO.
3) PC companion tries to find the phone. It says it may take few minutes to identify the phone if it has lots of files. After that the operation fails suggesting that PC companion could not find the phone.
I restarted both the phone and my device several times......did not work.
I uninstalled the MTP and USB drivers and restarted and got them reinstalled........didn't work either.
Any idea on what needs to be done?
I have tried all the ports and a different USB cable as well.
I even tried changing settings of the usb port as described in the below link..
Nothing worked
Is it possible to get the Sony specific drivers from somewhere?
Click to expand...
Click to collapse
I've got the same problem, but you can still use MyPhoneExplorer from
.fjsoft.at
to access your phones data. please also read the forum, because it needs an app on your phone too.
fjsoft.at/forum/viewtopic.php?t=11454
Also I've called with the xperia help line about a driver pack, but there aren't any lose available, exept what is in SEUS or PC Companion, but they don't work for me.
Can also some tell me if SEUS also will provide the new firmware 6.0.A.3.67? because SEUS tells me that my phone is uptodate, but I still have 6.0.A.3.62.
Install the latest version of media player, that worked for me.
Try connecting phone in Debug mode. On first time MTP driver installation will fail too but after that disconnect phone, disable Debug mode in phone and connect. Now it should working.
If will not working then go to Device manager on your PC, find "Mobile devices", select something with MTP in name, right click and choose "Uninstall". Disconnect phone, connect again and now it should working.
Worked for me!
Hurray! I fixed it on my computer WinXP sp3. I did everything with MTP bla bla winmedia11 even dev kit MTP = No fix.
go to Settings-> apps-> handle apps-> all-> MtpApp <open it.
Clear data and cache. (restart phone if you want)
plug the phone in USB and wait.. the scanner/camera thing comes up.
Right click on This computer (my computer?) chose "Handle" -> device manager -> scanners and printers-> right click on the "phone" -> settings -> device driver-> update.
Chose let windows search for XXX and voila MTP device driver found and installing.
(I'm using Swedish interface so the names of step might be wrong )
I can confirm that delete data / cache on MTP App indeed solved the problem. Thanks
So I have been following the walkthrough from TheeBookReader on youtube.
Followed him word for word, made the magic SD Card, that worked fine
Downloaded the hidden settings App, that worked fine.
While trying to access the Nook via Device Manager, it shows up as a portable device, and a USB Mass Storage Device.
I downloaded the USBDeview program in his walkthrough, and everytime I uninstall the driver(already got rid of every other android and B&N driver), it automatically starts reinstalling it.
I disabled automount, I disabled auto updating, both USB Debug boxes are checked, I've disabled every feature I can think of that allows devices to do anything without my express permission but it just keeps doing it.
(Running Windows 7 Professional 32 Bit via Bootcamp on a Late 2008 MacBook 5,1.)
Also, my Nook doesn't allow me to do anything while its hooked up to the computer via USB cable. I get this little screen which I have added as a photo attachment. That lovely: USB Mode You may now safely move files from your PC to NOOK.
According to the walkthrough, I should be golden. Can someone please point out where I went wrong or missed something. I've been doing this for 3 hours now and I'm starting to foam at the mouth a bit.
WMartPD said:
So I have been following the walkthrough from TheeBookReader on youtube.
Followed him word for word, made the magic SD Card, that worked fine
Downloaded the hidden settings App, that worked fine.
While trying to access the Nook via Device Manager, it shows up as a portable device, and a USB Mass Storage Device.
I downloaded the USBDeview program in his walkthrough, and everytime I uninstall the driver(already got rid of every other android and B&N driver), it automatically starts reinstalling it.
I disabled automount, I disabled auto updating, both USB Debug boxes are checked, I've disabled every feature I can think of that allows devices to do anything without my express permission but it just keeps doing it.
(Running Windows 7 Professional 32 Bit via Bootcamp on a Late 2008 MacBook 5,1.)
Also, my Nook doesn't allow me to do anything while its hooked up to the computer via USB cable. I get this little screen which I have added as a photo attachment. That lovely: USB Mode You may now safely move files from your PC to NOOK.
According to the walkthrough, I should be golden. Can someone please point out where I went wrong or missed something. I've been doing this for 3 hours now and I'm starting to foam at the mouth a bit.
Click to expand...
Click to collapse
if you installed your nook tablet drivers correctly, the nook should come up under Android Phone -> Android ADB Composite Device. Can you confirm that?
the only reason i can think of for usb mode going active is because of automount, but since you said you disabled automount then i am not sure...
Hey there,
Here is a list of what I have before I get started.
Samsung Galaxy Tab 10.1 Wifi (P7510)
Android Version - 3.2
Kernel Version - [email protected]#1
Build Number - INFAMOUS TAB 0.1 P7510UEKMM
Basically I have no access to my tablets internal SD card via my PC (Windows 7 and KIES)
I bought this tablet from a friend who rooted and flashed with the INFAMOUS mod.
I have searched all over the web for an answer and cant find something for this case specifically.
Each time I plug in my tab, my PC tells me that the Hardware ID is missing.
I can see the tablet in my Devices and Printers (displayed as SAMSUNG_android) as well as in my Device Manager. In device manager it says the drivers are up to date and functioning.
What have I tried?
USB Debugging (On and Off)
Clearing cache via recovery mode
Updating drivers via W7 and KIES via Samsung
I have tried following a few threads on installing the KIES software without internet connectivity. However I would rather not use the KIES Software anyway as it is kind of garbage.
I am looking to have access to the internal SD card so I can flash a new Rom on the Tab, however I would first like to even just have access to the file transferring.
Can anyone point me in the direction of help and me being able to enjoy this tablet?
I hope I have provided enough information. I am a pretty techy person and I understand how to do all of this but it seems like I am missing something really big.
Something to take note of, whenever the tab is plugged in (PC or Wall) there is a red x over the battery symbol and the tab charges very slowly.
Cheers
B
Snugglebutt said:
Basically I have no access to my tablets internal SD card via my PC (Windows 7 and KIES)
...
I am looking to have access to the internal SD card so I can flash a new Rom on the Tab, however I would first like to even just have access to the file transferring.
Click to expand...
Click to collapse
The Galaxy Tab doesn't expose the internal "sdcard" as a device that you can mount on your PC. If you enable it, it shows up as a MTD device.
The sdcard partition is formatted using a Linux native filesystem, not FAT, so Windows can't recognize it.
I use adb to push files onto the sdcard. ADB comes with the android SDK.
k1mu said:
The Galaxy Tab doesn't expose the internal "sdcard" as a device that you can mount on your PC. If you enable it, it shows up as a MTD device.
The sdcard partition is formatted using a Linux native filesystem, not FAT, so Windows can't recognize it.
I use adb to push files onto the sdcard. ADB comes with the android SDK.
Click to expand...
Click to collapse
As stated, make sure you have your tablet in MTP, and if so, make sure to update your drivers.
Settings > Storage > Additional Settings (top right) > MTP
To build on the above, if you have uninstalled Kies but also the Samsung USB drivers, you will be unable to connect the tab. Reinstall (or maybe uninstall and reinstall if you still have them) the drivers. A lot of the times that is the issue.
Go to Settings>Storage>Options/Info (The one on the upper right)>MTP(Check this one)
hope this help
FIXED
k1mu said:
The Galaxy Tab doesn't expose the internal "sdcard" as a device that you can mount on your PC. If you enable it, it shows up as a MTD device.
The sdcard partition is formatted using a Linux native filesystem, not FAT, so Windows can't recognize it.
I use adb to push files onto the sdcard. ADB comes with the android SDK.
Click to expand...
Click to collapse
To build on the above, if you have uninstalled Kies but also the Samsung USB drivers, you will be unable to connect the tab. Reinstall (or maybe uninstall and reinstall if you still have them) the drivers. A lot of the times that is the issue.
Click to expand...
Click to collapse
Ahhh ha! As soon as I uninstalled the driver that windows found and used the Google Driver that came along with the Android SDK, the tablet was recognized. Alas, I can finally use this tablet.
In the end it was as simple as a driver error, I spent a very long time searching last night and now I just feel silly.
The tablet still shows the red X over the battery symbol, whether I have MTP with USB Debugging on or off. I guess this can be avoided with certain ROMS. Anybody know of a ROM that avoids this?
Thank you all for your immediate responses!
B
Tid bit of info
H. Ess said:
As stated, make sure you have your tablet in MTP, and if so, make sure to update your drivers.
Settings > Storage > Additional Settings (top right) > MTP
Click to expand...
Click to collapse
Go to Settings>Storage>Options/Info (The one on the upper right)>MTP(Check this one)
Click to expand...
Click to collapse
By the way you two, there is no option in 3.2 for this.
In 3.2 its Applications/Development/USB Debugging
In storage there is no option to choose MTP, it seems that it always has been enabled and I cant find it anywhere in the settings to change it.
Thanks for the input though
Snugglebutt said:
By the way you two, there is no option in 3.2 for this.
In 3.2 its Applications/Development/USB Debugging
In storage there is no option to choose MTP, it seems that it always has been enabled and I cant find it anywhere in the settings to change it.
Thanks for the input though
Click to expand...
Click to collapse
For honeycomb and many others, debugging is always there. Under the storage option, you have an Additional Settings button usually and it should be present in there. I was always running3.2 until like a couple days ago so surprised its not there. Oh well problem solved lol
I'm having a similar problem with my tab not being recognised by my pc (win7 64) or in kies. It was originally an M380W (Korean) model, which I updated to a P7510. That all went fine, and the tablet works perfectly, except for the fact that my pc no longer sees it when it's plugged in. I tried uninstalling and reinstalling the drivers, but no dice. I'm going to see if adb works.