Right now, I am unable to make outgoing calls from my Archos 43 running UrukDroid 1.0 (I've tested using stock firmware 2.3.26) and I don't understand how I'm supposed to make calls by routing my call through google voice if I have no dialer. My setup looks like this: PBXes provides SIP -> use IPKall for a free washington state number -> use to validate google voice with a softphone (I used 3CXPhone). The only successful way I've been able to make calls was using 'connect with phone' on the google voice site, which called my sip number -> address and I was able to receive the call using Sipdroid base. I'm not going to have desktop access to google voice all the time though, so I tried CSipSimple as well, which just hangs up right away (Sipdroid hangs up instantly when you try sending the call) The weird thing is, it shows that Sipdroid is dialing [email protected] rather than the actual number, which makes sense to me because it's an SIP dialer/client. Now, I want my calls to be routed through google voice, not sent to my SIP provider. What is the easiest way to do this? Thank you!
Edited:
Setting up a trunk and outbound route in PBXes or using SIPSorcery (it doesn't actually provide SIP) just plays some really weird opera music on every outgoing call.
I used fring for sip and that was working ok.
comes with its own dailer and you can use the normal contacts.
Does anyone know how to assign a phone number to the Fascinate. My phone has no service and I am using GrooveIp to make and receive phone calls on WIFI using my Google Voice number. I am unable to install Google voice to handle texts since the Google Voice number does not show up in the phone....
You have to add a phone number from the google voice website. It could be any number, home phone, friend's phone, make sure the number you add has service cause google voice will call it with a verification number. Once you verify the number on the website make sure you disable it so that when people call you it does not forward to that phone, keep it on google chat so groove ip continues to work. Then when you go to the voice app it will list the number you verified, select it and you will have a few options based on what you want the voice app to do for calls, I usually "put do not use voice for calls" skip the voicemail part and you should be able to receive text and voicemail messages with the app. Hope this helps!
Does anyone have experience using Google Voice without a data plan? My sister just bought a phone to use with Page Plus, and is porting her number to Google Voice.
Do calls work correctly without data? I read a while back that Google implemented a feature in the Google Voice app that downloads the direct access numbers for all of your contacts when you first install the app. How does it handle new numbers that you dial?
Is there a good way to text people without saving their Google Voice "proxy" number, and still have it come from your Google Voice number, without using data?
I use Sipdroid with Google Voice on my tablet.
Inbound and outbound calls over WIFI work pretty well for me. I just dial regular phone numbers.
I've never really used texting with Google Voice.
google voice pay as you go no data plane
Does anyone have recommendation on how to set this up to play somewhat reasonable all together.
I know functionality will be limited when no Wi-Fi is available but......
Text >GV>T-mob carrier>my phone
Call>GV>answer
- yes>got the call
-no> be able to see voice mail notification an call to check the voice mail
Just wanted to throw this out here... for those of us who want to run CM10 but depend on WiFi calling because of coverage issues.. here's something I've done that works great
Basically we're going to be using Google Voice (For the phone provider) that's linked to a SIP account (SIP is the standard for VOIP), and we're going to use Conditional Call Forwarding to ensure calls go to our google voice number when we don't have server, but connected to WiFi.
First, you need a google voice account. Once you have created an account, make sure you log in/place a call at least once using Gmail (In the google voice phone settings, there's an option to have it forward calls to "Gmail", you want to make sure that's checked as well)
Okay, once you've done that, and you have made a test call... you need to sign up for this Google Voice SIP gateway https://simonics.com/gvgw/
This will, in a nutshell, establish a gateway between google voice's gmail call interface, and a SIP account. This will allow you to use a SIP account to make calls through your google voice number. Make sure you write down/store the information the Simonics gateway gives you once you sign up, you cant get it again!
After you register with the Simonics gateway, you will be given a SIP server, a username, a "secret" (Password), the registration string isn't important unless you're going to be using Asterisk, which we are not.
Now, once you have all this information, download the app CSipSimple (Best SIP client on android) https://play.google.com/store/apps/...lt#?t=W251bGwsMSwxLDEsImNvbS5jc2lwc2ltcGxlIl0.
(Optional)
You can also get the codec pack, which will give you a wider range of codecs to use.. but I find the default just fine.
https://play.google.com/store/apps/...5jc2lwc2ltcGxlLnBsdWdpbnMuY29kZWNzLnBhY2sxIl0.
Okay! Now that we have all that done, we're going to configure CSipSimple to connect to the Simonics google voice gateway. CSipSimple has great integration with the stock dialer. Open up CSipSimple... the initial config will pop up, here you can choose to integrate it with the Android dialer (which I recommend if you're replacing wifi calling), select "Available on WiFi" (Unless you want to use this over the cellular network as well, to save on minutes, only uses data) and you can also choose if you want to allow CSipSimple to operate over mobile networks (I'm allowed to use mobile, is the option name) pick your options, then save. Now you'll be presented with a list of VOIP providers etc.. scroll all the way down and select "Advanced" configuration.
Account name: Anything you want
Caller ID: Anything you want, but I suggest either your mobile # or your google voice number
Server: Whatever the Simonic's gateway provided you, this can be different so make sure you wrote all that down!
Username: What the Simonic's gateway provided you
SIP Authentication ID: Leave this blank, it will default to the username.
Password: the "Secret" the simonics gateway provided you
There will be a checkbox that asks to use TCP instead of UDP. If you're going to be taking incoming calls on this often, I'd recommend using TCP (it's much less battery intensive than UDP). UDP is the preferred method, but it will use a LOT more battery if you plan on being connected often.
Proxy: same exact thing here as "server", example: mine is gvgw3.simonics.com
Save that.
If everything is correct, after you save the account should register, and turn green showing "registered"
Okay! Now we can make calls using our google voice account, so let's test it and make sure it's working. Go ahead and hit "Accounts" at the top left (The "back" arrow) or simply hit the back softkey. This should take you to the dialer (This is CSipSimple's dailer, but CSipSimple has also integrated with the stock dialer, so when you make a call a menu will pop up asking if you want to use your Google Voice SIP gateway account, or regular mobile network.. if you don't want this menu every time you make a call, I suggest turning off the "I'm allowed to use mobile network" feature and turn off android dialer integration)
Dial this number: 1 354 415 1595 - This is what's called an ECHO test line, it's a regular land-line number.. you should hear a voice saying hit "1" for an ECHO test, "2" for music on hold. Hit the 1 key, and start talking. You should hear an echo of your voice... if you hear yourself talking, GREAT! Outgoing calls are working!
Now we want to configure what's called Conditional Call Forwarding/Unconditional Call Forwarding so that all calls to our mobile number will be forwarded to our google voice number when we do not have a signal (or in the case of unconditional, always), you can also set up what's Unconditional Call Forwarding... this is useful if you want to have calls forwarded to your google voice number no matter what. I usually turn off the radio when connected to WiFi though (saves a lot of battery), to ensure I don't have a mobile signal ****YOU WILL NOT RECEIVE TEXT MESSAGES IF YOU DO THIS****, so it's up to you if you want to turn the radio off or not. If you don't, you'll need to use unconditional call forwarding.
Now here's the deal: WIth T-Mobile, Conditional Call Forwarding (THIS IS VERY IMPORTANT) is limited to a total of 500 minutes per billing cycle. It doesn't matter if you're on unlimited, 1000 minutes, whatever. You get a TOTAL of 500 Conditional Call Forwarding minutes each cycle. Yes, it sucks. But that's what we have to deal with if we want to use CM10 with functional wifi calling that rings you when someone calls your mobile number. If you want to avoid using these minutes, you can simple call the person back (Using your SIP account), or give your google voice # (instead of mobile number) when someone calls you, and have them call you right back. ALSO, Conditional Call Forwarding is what forwards calls to your voice mail, so if you use it, MAKE SURE TO SET IT BACK TO THE NUMBER IT WAS AT ORIGINALLY, OR CALLS WILL NOT GO TO YOUR VOICEMAIL. You can see what this number is by using the short code # # 62 # in your dialer, using your mobile network.
There's several modes of conditional call forwarding. Forward if BUSY, Forward if NO REPLY, Forward if NOT REACHABLE (no signal). You can set up forwarding to your google voice for any of these, but I only recommend NOT REACHABLE, because it simply doesn't make sense for the other two. There's several ways to configure call forwarding. I recommend using the stock dialer's built in feature, but you can also use Short Codes to activate it. Open the stock dialer, click the menu button, then settings. Near the bottom of the Settings, there should be a "Call Forwarding" option. In there you'll see all three forwading settings (Busy, not reachable, unanswered) as well as the original number it's set to (your voicemail). All you do is simply change the "Forward when unreachable" to your google voice number. Remember, for this to be in use 100% of the time you're on WiFi, you will have to turn off your cellular radio. If Text Messages are important to you, I recommend using UNCONDITIONAL (Always Forward in the dialer->forwarding settings).. this will have calls forwarded to your google voice number NO MATTER WHAT, so make sure you turn it off when you leave WiFi.
Unconditional Call Forwarding, on the other hand, deducts from the minute plan you subscribe to. You can still use the above methods to avoid using your minutes, but just be aware that if you use unconditional call forwarding it WILL deduct from your minute bucket.
Please be aware that you have to have a mobile signal to configure call forwarding, so you need to turn it on before you leave service/enter wifi, or simply always have Unconditional Forward if Not Reachable forwarded to your google voice number. Honestly, I use Google Voice for my voicemail as well, so I have all three of my forwards always set to my Google Voice number, you might want to consider this option as well, as it makes it much more seamless. You can use the Google Voice app for visual voicemail as well as free transcription, and it's much much better than T-Mobile's solution.
Here's a list of short codes for call forwarding: http://support.t-mobile.com/docs/DOC-4319
These are very useful if you plan on using Tasker to automate any of this (This is what I do, to make the process very seamless when I enter WiFi)
I know this isn't nearly as simple as the stock wifi calling solution, and it doesn't integrate nearly as well... but it works. Once you have this configured, you'll be able to receive/make calls on WiFi without issue. You'll also have a method of calling using your data connection that doesn't use minutes if you need that, as well. There's other ways to do this, such as using an app such as "Groove IP" or "Talkatone", and those work very well. I prefer the SIP gateway method, because I can configure a SIP softphone on any number of devices, including my android device. For those standalone apps such as "Groove IP", you would do pretty much the same thing, but you don't need the Sip Gateway, and you also wouldn't need CSipSimple (which I find is superior to all the other VoIP apps)... all you would do is simply configure Unconditional/Conditional call forwarding to your Google Voice number and use whatever app you want. You could also use Android's build in SIP functionality (it's built into the dialer!) But I find it very unreliable and couldn't get it to register reliably with the SIP gateway... but that might be a great option as well.
Please title this correctly.
This is 'How to get Google Voice working on your phone'... Not a viable workaround for 'cell-service-over-WiFi' style wifi calling.
Notes:
1) Monthly4G customers DO NOT HAVE conditional forwarding
2) This does not allow you to recieve MMS.
3) The only way you can use google voice with your real mobile-number is if you port it to Google, at which point you will never get MMS at that number again (because GV can't handle it properly)....
Now, does it work to have a usable phone at home w/o service? Sure, on a different number & with limited messaging...
But it is not a true WFC workaround.
dcacklam said:
This is 'How to get Google Voice working on your phone'... Not a viable workaround for 'cell-service-over-WiFi' style wifi calling.
Notes:
1) Monthly4G customers DO NOT HAVE conditional guys over on nal forwarding
2) This does not allow you to recieve MMS.
3) The only way you can use google voice with your real mobile-number is if you port it to Google, at which point you will never get MMS at that number again (because GV can't handle it properly)....
Now, does it work to have a usable phone at home w/o service? Sure, on a different number & with limited messaging...
But it is not a true WFC workaround.
Click to expand...
Click to collapse
Well yeah I'm quite aware of the limitations. There's really no other viable alternative at the moment. Maybe someone can get the kineto app and libs from the sensation working but I highly doubt it, as the guys over on the sensation forum have been trying for a while now... Basically it's up to t mobiles, haha. I believe the only working device with jelly bean and wifi calling is the note 2, and sgs3....and once again its deeply embedded within the touchwiz framework.. The guys over on sgs3 forum even have a 350$ bounty for a non touchwiz working port. Doesn't look very promising but it's to be expected with something like uma... Maybe someone will figure it out. For someone who works in a complete t mobile dead zone, the only other viable option is sticking with Ics, and that's simply not something I want. Then again, I've always basically given my gvoice number out, and no MMS is very little impact considering you can send stuff over email, and every single carrier seems to have an email gateway... It is a major pain to have people send stuff to your Gmail acct. Instead of regular MMS, though,.... It's definitely not Ideal but it's a lot better than no service, an using ICS/sense builds.
I wasn't aware that monthly 4g didn't get conditional, kind of sucks. Could always use unconditional, if most people use your mobile number you would completely be dropping messages so i do understand the hesitation on that. I've been wanting sms/MMS. Forwarding options for a long time now, would be nice if carrier sms could utilize xmpp or sip messaging to handle sms forwards, but sms is another huge hack job that sorely needs replacement and MMS just a fancy if not severely limited email.
So yeah man, not many other options out there right now. If you're someone who relies on sms/MMS heavily and most contacts use your mobile number, I can definitely see where that would be an issue. Most people I communicate with on a daily basis are very tech oriented, so it's honestly not that big of a deal breaker (to me). I've just found that the Sip gateway and CSipSmple work orders of magnitude better than any stand alone app implementation. If you have any alternatives (besides using ics/sense builds) I'd love to know them, I was a huge user of wifi calling (about. 70% of all my calls) so i'm open to try everything.
Lol get your friends and family to get viber you get to keep your number and sms and MMS and since these days every one has a smart phone an app like viber is quite nice especially if everyone had it on their phones... That's what I use when I don't have signal and have told friends and family to reach me on viber if they can't otherwise
Sent from my Amaze 4G using xda app-developers app
ericdjobs said:
I wasn't aware that monthly 4g didn't get conditional, kind of sucks. Could always use unconditional, if most people use your mobile number you would completely be dropping messages so i do understand the hesitation on that. I've been wanting sms/MMS. Forwarding options for a long time now, would be nice if carrier sms could utilize xmpp or sip messaging to handle sms forwards, but sms is another huge hack job that sorely needs replacement and MMS just a fancy if not severely limited email.
Click to expand...
Click to collapse
If you use 'unconditional forward' then you will never get another call again. All your calls will be forwarded to G-Voice, which will send them to G-voicemail.
We'll see about wifi calling.
BTW, the Kineto/UMA app does run on our CM9. There's a kernel driver missing for GAN, and of course CM9 does not have data. It crashes on CM10 because of a missing native library for audio-recording...
The Movial/IMS app (From Amaze Stock) runs on CM10 but the setup screen is full of sense rubbish... However the Sense rubbish might be wrapp-able back to stock-Android, but that is a long-shot...
Skip all steps and install groove ip. And sign in with your Google voice login
Sent from my HTC_Amaze_4G using Tapatalk 2
dilfatx said:
Skip all steps and install groove ip. And sign in with your Google voice login
Sent from my HTC_Amaze_4G using Tapatalk 2
Click to expand...
Click to collapse
Yeah you can do that if you want, and it's definitely a much more simpler approach and it should be sufficient for most people.
But the SIP method gives you much more flexibility, like the option of using Speex/GSM codecs (which compensate for jitter and packet loss) while Groove IP hooks directly into the google talk API, thus you are stuck with G.711 mu-law codec, and that's not the best option all of the time. Using Speex/GSM codecs will give you slightly reduced call quality but much better reliability and they are much more resistant to congestion network situations or high latency.. it's a better calling experience all around IMO.
Also, using a SIP solution you're able to hook into an asterisk server if you so desire (which is important to me, personally) and manage multiple lines using one softphone.
At the end of the day though, if you have access to fast, reliable wifi whenever you need to make calls, Groove IP gets the job done just fine. But for someone who wants a lot more functionality and features, using the SIP gateway will provide that. Also, you can use it as a trunk for an asterisk server, for those of us who utilize that sort of thing.
Android stock dialer
Hi, thanks for sharing this! I was wondering if there's a way to configure this directly in Android's stock dialer (just as can be done with pbxes.org)? Thanks!
CM11 Dialer: Dialer/Browser automatically add "+1" prefix which blocks outgoing calls
Great experiences so far with CM11. Persistent issue with native dialer (as well as Google Dialer) and unnecessary plus-code dialing for domestic calls.
However, I've noticed a persistent bug: the dialer will not complete any call that begins with a plus code extension (for example, “+1 555 6946). The dialer produces a busy signal instead of completing the call. However, if I edit it before calling to remove the “+1” prefix, the call completes normally. This problem occurs even though I am only making domestic calls within the US, and occurs in every tested version of Cyanogenmod (although it is absent in the rooted stock rom).
I can replicate the problem for any number that I look up on a web browser through Google. For example, if I look up “Chipotle New York” and hit “call” it automatically sends the dialer a number with a “+1” extension. Again, this results in a busy signal unless I edit the number to remove the “+1” prefix. This means that I cannot simply edit all of my contacts to remove the prefix since the problem will occur anytime I send a contact to my dialer through a browser.
Thanks in advance for any insights.
Device Information:
- CyanogenMod 11-20141112-SNAPSHOT-M12-jewel
- Android version 4.4.4
- Baseband version 1.13.11.1105
- Sprint (USA)
- on HTC Jewel (Evo 4g LTE)
Saw you hadn't gotten an answer to this in threads across a few sites, so hopefully this finds you. I've not found a proper fix for this bug either, but have been able to work around it by using an app called Prefixer from the store https://play.google.com/store/apps/details?id=com.tftbelow.prefixer&hl=en. A single outgoing rule is free. Just create one to remove all instances of +. The + will be put into the dialer still from google or calling back a number that came in with it, but when you hit send, the app intercepts the number, removes the + and the call connects.
Its a hack, but it works for now. Happy dialing!