[SOLVED] I sorta messed up AT&T Note... help? - AT&T Samsung Galaxy Note I717

I have an AT&T Branded i717 Note. And I screwed up.
I checked out the Super Everything thread (which is great!) but stupidly downloaded the Rogers stock ODIN (which seems to be a full flash - PIT, Bootloader, PDA, PHONE, and CSC).
Thank you djkid for providing it in this thread: forum.xda-developers.com/showthread.php?t=1657262
But anyway... I'm stupid because I flashed it (I know, I know, I was too eager and in a rush to flash something). Phone boots ok and everything, but it complains about the USB Storage being blank (or in an unsupported format), even though nothing is connected to it. If I put a MicroSD card in, it constantly shows "safe to remove SDCard".
I assume the partitions have been set incorrectly? I've been looking all over for an AT&T stock ODIN (that is full like the Rogers one mentioned above) but no luck. I downloaded and tried a few of the regular AT&T stock ODINs in the forum (thank you for those posts), but they only contain certain parts and they don't solve the USB / MicroSD issue I'm having.
Can anyone help?

Just go back and get rhe correct Odin3 files, put phone in download mode, start Odin, connect phone, and flash. I put the Rogers rom and modem on my phone last week (very laggy).

LaZiODROID said:
I have an AT&T Branded i717 Note. And I screwed up.
I checked out the Super Everything thread (which is great!) but stupidly downloaded the Rogers stock ODIN (which seems to be a full flash - PIT, Bootloader, PDA, PHONE, and CSC).
Thank you djkid for providing it in this thread: forum.xda-developers.com/showthread.php?t=1657262
But anyway... I'm stupid because I flashed it (I know, I know, I was too eager and in a rush to flash something). Phone boots ok and everything, but it complains about the USB Storage being blank (or in an unsupported format), even though nothing is connected to it. If I put a MicroSD card in, it constantly shows "safe to remove SDCard".
I assume the partitions have been set incorrectly? I've been looking all over for an AT&T stock ODIN (that is full like the Rogers one mentioned above) but no luck. I downloaded and tried a few of the regular AT&T stock ODINs in the forum (thank you for those posts), but they only contain certain parts and they don't solve the USB / MicroSD issue I'm having.
Can anyone help?
Click to expand...
Click to collapse
Well we all screw up once in a while. I had to return my Galaxy note to stock last night that what I would suggest you try first. if you cant connect use the usb try Airdriod to transfer the files. i used the stock att files from http://rootgalaxynote.com/ but if you cant find them let me know Ill send you what I have.

LaZiODROID said:
I downloaded and tried a few of the regular AT&T stock ODINs in the forum (thank you for those posts), but they only contain certain parts and they don't solve the USB / MicroSD issue I'm having.
Click to expand...
Click to collapse
I have flashed stock AT&T roms via Odin, but the USB Storage / MicroSD issue remains.
Is it because the stock AT&T roms I am trying only come with certain parts?
i.e. the Rogers one I flashed (found in the forum) had a few files... the PIT file, CDC file, along with the system/modem etc. None of these AT&T stock roms I have downloaded have these kinds of parts (though that isn't stopping me from trying them out of desperation)

rangercaptain said:
Just go back and get rhe correct Odin3 files, put phone in download mode, start Odin, connect phone, and flash. I put the Rogers rom and modem on my phone last week (very laggy).
Click to expand...
Click to collapse
Ditto......in my quest to unlock the RAT....g
---------- Post added at 12:38 PM ---------- Previous post was at 12:36 PM ----------
LaZiODROID said:
I have flashed stock AT&T roms via Odin, but the USB Storage / MicroSD issue remains.
Is it because the stock AT&T roms I am trying only come with certain parts?
i.e. the Rogers one I flashed (found in the forum) had a few files... the PIT file, CDC file, along with the system/modem etc. None of these AT&T stock roms I have downloaded have these kinds of parts (though that isn't stopping me from trying them out of desperation)
Click to expand...
Click to collapse
I'm quite certain that the ATT stock odin .tar file is complete...I've used it numerous times.
It has to be another issue...IMHO
And you are pulling the stock odin .tar from the everything thread ??
this is the one I'm talking about...and have used many times....g
http://forum.xda-developers.com/showthread.php?t=1506330

With all this said, do we need to add something to the Super Page? I have the off ICS odin, totally bloated by ATT , (only 1gb in size) which is on my server profile, just never push it out or added it to the Super Page. Do or should we list it...on the Super Page ?
LaZiODROID said:
I have an AT&T Branded i717 Note. And I screwed up.
I checked out the Super Everything thread (which is great!) but stupidly downloaded the Rogers stock ODIN (which seems to be a full flash - PIT, Bootloader, PDA, PHONE, and CSC).
Thank you djkid for providing it in this thread: forum.xda-developers.com/showthread.php?t=1657262
But anyway... I'm stupid because I flashed it (I know, I know, I was too eager and in a rush to flash something). Phone boots ok and everything, but it complains about the USB Storage being blank (or in an unsupported format), even though nothing is connected to it. If I put a MicroSD card in, it constantly shows "safe to remove SDCard".
I assume the partitions have been set incorrectly? I've been looking all over for an AT&T stock ODIN (that is full like the Rogers one mentioned above) but no luck. I downloaded and tried a few of the regular AT&T stock ODINs in the forum (thank you for those posts), but they only contain certain parts and they don't solve the USB / MicroSD issue I'm having.
Can anyone help?
Click to expand...
Click to collapse
gregsarg said:
Ditto......in my quest to unlock the RAT....g
---------- Post added at 12:38 PM ---------- Previous post was at 12:36 PM ----------
I'm quite certain that the ATT stock odin .tar file is complete...I've used it numerous times.
It has to be another issue...IMHO
And you are pulling the stock odin .tar from the everything thread ??
Click to expand...
Click to collapse
ladyhaylin said:
Well we all screw up once in a while. I had to return my Galaxy note to stock last night that what I would suggest you try first. if you cant connect use the usb try Airdriod to transfer the files. i used the stock att files from http://rootgalaxynote.com/ but if you cant find them let me know Ill send you what I have.
Click to expand...
Click to collapse
BTW very nice Sig Logo Picture....since BStar is my DD, LOL

gregsarg said:
this is the one I'm talking about...and have used many times....g
http://forum.xda-developers.com/showthread.php?t=1506330
Click to expand...
Click to collapse
Yes - the big RAR.
I will try it again then. I will do whatever it takes to get this thing back to normal. When flashing this one, should I check "re-partition"? or just leave all check boxes as they come....
Thanks everyone for jumping in

LaZiODROID said:
Yes - the big RAR.
I will try it again then. I will do whatever it takes to get this thing back to normal. When flashing this one, should I check "re-partition"? or just leave all check boxes as they come....
Thanks everyone for jumping in
Click to expand...
Click to collapse
Instead of having to go back all the way to gingerbread, use this odin file and flash official stock ICS which it has recovery, modem, kernel and ROM.
http://forum.xda-developers.com/showthread.php?p=28525924
Posted by 1timerlgk
RoloRacer Paranoid on JellyBean

LaZiODROID said:
Yes - the big RAR.
I will try it again then. I will do whatever it takes to get this thing back to normal. When flashing this one, should I check "re-partition"? or just leave all check boxes as they come....
Thanks everyone for jumping in
Click to expand...
Click to collapse
Simply run it ....don't re-partition ....let Odin do that ..
And GB or ICS is your choice ...but the original device partitions are GB ...not that it matters entirely, but if you want box stock ...it's the GB ...g

bigjoe2675 said:
With all this said, do we need to add something to the Super Page? I have the off ICS odin, totally bloated by ATT , (only 1gb in size) which is on my server profile, just never push it out or added it to the Super Page. Do or should we list it...on the Super Page ?
BTW very nice Sig Logo Picture....since BStar is my DD, LOL
Click to expand...
Click to collapse
I would Joe.....
we have the brick .tar,( GB) and It would be good to add the ICS .tar next to it I think....g

gregsarg said:
Simply run it ....don't re-partition ....let Odin do that ..
And GB or ICS is your choice ...but the original device partitions are GB ...not that it matters entirely, but if you want box stock ...it's the GB ...g
Click to expand...
Click to collapse
Alright. Loaded up Odin 1.85 (from the Super Everything thread), and grabbed the ICS stock recommended above (filename:
I717UCLF6_I717ATTLF6_I717UCLF6_HOME.tar.md5)
Flashing looked like it was going well!
Until it died at amss. Here is the log:
Code:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I717UCLF6_I717ATTLF6_I717UCLF6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> amss.bin
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Since the majority of the flash finished, I thought I'd reboot the phone. Booted up OK (into what looks like the initial AT&T setups), but the USB issue remains. In the pic below, there is no USB anything attached to the phone, and there is a 1gig MicroSD card in the slot. (It offers to format the USB storage, which does nothing, and the internal sd storage doesn't seem to be recognized, and the external sd storage always says it is safe to remove it)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I await your wisdom. Thanks for the help so far guys.

Try and flash back to the stock ROM, I'm telling you go to rootgalaxynote.com use their step by step picture process.
If you want I have the stock PDA I'll send you it
sent from in the closet

ladyhaylin said:
Try and flash back to the stock ROM, I'm telling you go to rootgalaxynote.com use their step by step picture process.
If you want I have the stock PDA I'll send you it
sent from in the closet
Click to expand...
Click to collapse
I would appreciate that if you can. All I'm seeing on rootgalaxynote is ICS roms, ICS leaked roms and ones that look like custom roms.
The ROM I just flashed ( I717UCLF6_I717ATTLF6_I717UCLF6_HOME.tar.md5 ) -- is it not stock? Or is it that since it's ICS, it's too new for me to flash to get back to basics....
Thanks lady

Pm your email
http://rootgalaxynote.com/galaxy-no...brick-att-galaxy-note-sgh-i717-android-2-3-6/
(unroot and unbrick)
Root
http://rootgalaxynote.com/galaxy-note-root/how-to-root-att-galaxy-note-sgh-i717attrogerstelusbell/
Sent from my SAMSUNG-SGH-I717 using xda premium

ladyhaylin said:
Pm your email
http://rootgalaxynote.com/galaxy-no...brick-att-galaxy-note-sgh-i717-android-2-3-6/
(unroot and unbrick)
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
Alright. Downloaded and flashed attstockrom.tar (stock gingerbread AT&T) via Odin, but it didn't seem to help. It still has the USB Storage icon in the notification bar, saying it has an unsupported file system. Attempt to format it results in nothing... notification stays.
For this flash, I removed the MicroSD card. Flash was successful, and booted into the system. Below is a screenshot of the Storage area of Settings.
I'm thinking that the Rogers flash I originally did (to start this whole mess) maybe set the partitions wrong (or just different from this AT&T model phone)... is this possible? I don't know much about Samsung flashes (yet!). Also - I notice that the Odin 1.85 I grabbed (from the Super Everything thread) came with a PIT file (named u1_02_20110310_emmc_EXT4.pit) - but I don't want to flash it without knowing what it is exactly for. Any ideas on this? High brick risk?

Brick risk? Hell no. The pit file tells Odin how to partition the phone. Use it and see if your results are at all different.
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2

LaZiODROID said:
Alright. Downloaded and flashed attstockrom.tar (stock gingerbread AT&T) via Odin, but it didn't seem to help. It still has the USB Storage icon in the notification bar, saying it has an unsupported file system. Attempt to format it results in nothing... notification stays.
For this flash, I removed the MicroSD card. Flash was successful, and booted into the system. Below is a screenshot of the Storage area of Settings.
I'm thinking that the Rogers flash I originally did (to start this whole mess) maybe set the partitions wrong (or just different from this AT&T model phone)... is this possible? I don't know much about Samsung flashes (yet!). Also - I notice that the Odin 1.85 I grabbed (from the Super Everything thread) came with a PIT file (named u1_02_20110310_emmc_EXT4.pit) - but I don't want to flash it without knowing what it is exactly for. Any ideas on this? High brick risk?
Click to expand...
Click to collapse
can you format the card on with your computer?

kinghorsey said:
Brick risk? Hell no. The pit file tells Odin how to partition the phone. Use it and see if your results are at all different.
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2
Click to expand...
Click to collapse
Crap. Loading the PIT file (u1_02_20110310_emmc_EXT4.pit) along with the stock AT&T GB wouldn't get the flashing started. It failed at the PIT check part (and I notice on the phones screen it says "SECURE CHECK FAIL : PIT"
I also tried using the above PIT with the stock AT&T ICS (to see if it would be different.. same result).
Code:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

LaZiODROID said:
Crap. Loading the PIT file (u1_02_20110310_emmc_EXT4.pit) along with the stock AT&T GB wouldn't get the flashing started. It failed at the PIT check part (and I notice on the phones screen it says "SECURE CHECK FAIL : PIT"
I also tried using the above PIT with the stock AT&T ICS (to see if it would be different.. same result).
Code:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
LORD HAVE MERCY :/ okay darling
what are you trying to do exactly?

ladyhaylin said:
LORD HAVE MERCY :/ okay darling
what are you trying to do exactly?
Click to expand...
Click to collapse
Thanks for sticking with me
I just want this USB Storage / MicroSD problem to be fixed. This is an AT&T i717. It all started when I flashed a stock Rogers ROM. The stock Rogers rom had a file for each field in ODIN (PIT, BOOTLOADER, PDA, PHONE, and CSC). I think that it re-partitioned the phone (in some foreign way that the AT&T phone no longer sees the MicroSD. It also no longer sees the internal storage. Also, the notification bar complains that USB Storage is on, and whatever is attached to the phone is in an unsupported format.). There is no USB anything attached to the phone. It is confused (and so am I).
Re-flashing the AT&T stock roms (that you guys kindly pointed me to) flash OK, but they don't solve the issue. My guess is this - do I need an AT&T specific PIT file to repartition this thing back to normal?

Related

Followed "how to go back to stock..." sticky==WONT START UP, PLZ HELP

Was stuck on dl01 with voodoo, bloatware frozen, rooted, and using launcherpro.
I followed the first link in that sticky: http://forum.xda-developers.com/showthread.php?t=908451
and now my phone wont boot up. when I turn it on I see the samsung logo and then it goes through this:
--Wiping data--
Formatting FOTA...
Formatting DATA...
Data Wipe failed.
Formatting Cache
Formatting DBDATA
Wipe_Data Failed.
Click to expand...
Click to collapse
then it will go back to the samsung logo and go around in circles again.
everything went fine with odin. This is what the little message window said:
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> Enter CS for MD5..
<ID:0/005> Check MD5.. Do not unplug the cable..
<ID:0/005> Please wait..
<ID:0/005> Removed!!
<ID:0/005> Removed!!
<ID:0/005> Removed!!
<ID:0/005> Checking MD5 finished Sucessfully..
<ID:0/005> Leave CS..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> factoryfs.rfs
<ID:0/005> modem.bin
<ID:0/005> recovery.bin
<ID:0/005> zImage
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
I have no idea what went wrong but now i have no phone and this sux big time.
Dont panic this has happened to me.
Try this link:
http://forum.xda-developers.com/showthread.php?t=1026746
And use the method in SECTION 2: HEIMDALL
Rockstar52 said:
Dont panic this has happened to me.
Try this link:
http://forum.xda-developers.com/showthread.php?t=1026746
And use the method in SECTION 2: HEIMDALL
Click to expand...
Click to collapse
will take a look at that in a minute thanx.
but what the hell went wrong? was it something to do with voodoo?? none of the steps said to disable it or anything....
Yes you must disable VooDo before you do anything. Voodo is a real pain if your a new to flashing.
Rockstar52 said:
Yes you must disable VooDo before you do anything. Voodo is a real pain if your a new to flashing.
Click to expand...
Click to collapse
okay this tutorial is not working. I went strait to heimdall step two and I get two problems.
1) in step 3 it says "Now drop the usb drop down box and you will find an option for SAMSUNG android composite ADB device, or Samsung composite usb driver..."
I dont get that, I get "unknown device" My computer is 6 years old and i have always had problems with the usb recognizing my fascinate. It always says some type of problem and when i troubleshoot it says no drivers are installed even though i have installed them.
2)when I select the unknown device and hit install drivers i get installing drivers failed.
If you can get odin to work again use atlas_v2.2.pit to format back to rfs file-system. Use the PIT button in odin.
fupamobile said:
okay this tutorial is not working. I went strait to heimdall step two and I get two problems.
1) in step 3 it says "Now drop the usb drop down box and you will find an option for SAMSUNG android composite ADB device, or Samsung composite usb driver..."
I dont get that, I get "unknown device" My computer is 6 years old and i have always had problems with the usb recognizing my fascinate. It always says some type of problem and when i troubleshoot it says no drivers are installed even though i have installed them.
2)when I select the unknown device and hit install drivers i get installing drivers failed.
Click to expand...
Click to collapse
Definitely try to Odin the Pit 2.2 that DMT suggested.
Here's a link to a giude that should help get you back to stock as it isn't as intimidating for some as the un-bricking one: http://forum.xda-developers.com/showthread.php?t=1124391
And if that fails might I suggest trying it on a more up to date PC, maybe your issues have come from that if your pc never recognized the phone properly.
Nnneeeedd heellp nowwww!!!!!!!!!!
Go to the development stickies and go to the 2 one...how to go from
Cm7 to anything else...that's not the official title but it its something like that. The links for the eb01. tar, the atlas 2.2pit and newer odin versions are all in the first post.
I use odin 1.7..which version are you on? I'm sure if you use odin 1.7 or newer and put the 2.2 atlas pit file in the pit section with repartition checked and put the official vzw eb01 .tar in the pda section and run it..that will get your phone back in stock unrooted bloated form but at least your phone will work and then you can go and flash what you like..but I would try a different odin version and the eb01 with the pit file and you will get your phone back
Sent from my SCH-I500 using XDA App
Are you willing to just go back to stock or start all over again?
Put the phone in Download mode
Remove battery
plug usb into PC
plug usb into phone [battery still out]
push [and hold] volume button down
Should see yellow triangle [once you see this you can let go off the volume]
Use Odin then to flash the Stock image to your phone.
Link to ODIN v1.3 http://www.mediafire.com/download.php?r5izui8a3trpo85
Download the ED01 stock rom
Put it into the PDA section of Odin and flash and Boom Back to stock!
Stock ED01 http://www.multiupload.com/6ET46L1ATD
Nothing will be deleted off of your sd card
xwhofarted said:
Are you willing to just go back to stock or start all over again?
Put the phone in Download mode
Remove battery
plug usb into PC
plug usb into phone [battery still out]
push [and hold] volume button down
Should see yellow triangle [once you see this you can let go off the volume]
Use Odin then to flash the Stock image to your phone.
Link to ODIN v1.3 http://www.mediafire.com/download.php?r5izui8a3trpo85
Download the ED01 stock rom
Put it into the PDA section of Odin and flash and Boom Back to stock!
Stock ED01 http://www.multiupload.com/6ET46L1ATD
Nothing will be deleted off of your sd card
Click to expand...
Click to collapse
Well I got the drivers installed and i was on to step 5 but heimdall.exe wont open.
I think I will just do it this way i guess. this is all because of stupid voodoo
Voodoo used to be a p.i.t.a but it really isn't that hard now with the newer cwm supporting both voodoo and non voodoo, the steps myself and the person who posted above me are describing direction for odin..not heimdall.I don't know much about heimdall or how to use it but you can get your phone back and working using odin
Use the link in junkboy0's reply..follow the directions in the first post.
fupamobile said:
Well I got the drivers installed and i was on to step 5 but heimdall.exe wont open.
I think I will just do it this way i guess. this is all because of stupid voodoo
Click to expand...
Click to collapse
Sent from my SCH-I500 using XDA App
efan450 said:
Go to the development stickies and go to the 2 one...how to go from
Cm7 to anything else...that's not the official title but it its something like that. The links for the eb01. tar, the atlas 2.2pit and newer odin versions are all in the first post.
I use odin 1.7..which version are you on? I'm sure if you use odin 1.7 or newer and put the 2.2 atlas pit file in the pit section with repartition checked and put the official vzw eb01 .tar in the pda section and run it..that will get your phone back in stock unrooted bloated form but at least your phone will work and then you can go and flash what you like..but I would try a different odin version and the eb01 with the pit file and you will get your phone back
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
what should i do about voodoo though?
i am going to do this as two of you have suggested:http://forum.xda-developers.com/showthread.php?t=1124391
but i dunno about voodoo. just ignore it for now? It addresses it in that post but i dont undestand what it is saying
using Odin and the stock image it will over write the voodoo
I have never used the heimdall way. I have been stuck in boot loops many times and ODIN has always saved the day!
As long as you can get to Download mode your phone can be fixed
fupamobile said:
what should i do about voodoo though?
i am going to do this as two of you have suggested:http://forum.xda-developers.com/showthread.php?t=1124391
but i dunno about voodoo. just ignore it for now? It addresses it in that post but i dont undestand what it is saying
Click to expand...
Click to collapse
Yup ignore voodoo for now...when you use the atlas2.2 file in the pit section and the eb01.tar in the pda section...if repartition isn't checked make sure you check it...run it and it will bring you to stock with voodoo removed and then you can flash whatever you wanted from there...if you get stuck,p.m.me and I'll send you files with complete directions but it would have to wait till I get home from work tonight..don't panic we'll get you up and running again!
Get the newest odin, eb01. tar, and atlas 2.2pit file, and I would grab
One of the newer recovery.tar files too so when your back to stock you can flash a working recovery if you want to flash some rom after all is fixed....i recommend the 3-30 fix all recovery, but just make sure you get a tar file so you can odin it after your phone is fixed.
Sent from my SCH-I500 using XDA App
xwhofarted said:
using Odin and the stock image it will over write the voodoo
I have never used the heimdall way. I have been stuck in boot loops many times and ODIN has always saved the day!
As long as you can get to Download mode your phone can be fixed
Click to expand...
Click to collapse
interesting.
in the q/a section there is a sticky on how to go stock. not only does it not tell me how to address voodoo(why i am here) but it tells me to go to DL09 and them OTA to eb01.
the method you guys are posting seems much more logical. it sends me strait to froyo and doesnt brick my phone because it just overwrites voodoo. correct?
once voodoo is "overwritten", is it gone off my phone? if not, should i address it at all after this tutorial? froyo is downloading right now
xwhofarted said:
using Odin and the stock image it will over write the voodoo
I have never used the heimdall way. I have been stuck in boot loops many times and ODIN has always saved the day!
As long as you can get to Download mode your phone can be fixed
Click to expand...
Click to collapse
I concur...soft bricked, boot looped, many many times and never used heimdall either
Sent from my SCH-I500 using XDA App
fupamobile said:
interesting.
in the q/a section there is a sticky on how to go stock. not only does it not tell me how to address voodoo(why i am here) but it tells me to go to DL09 and them OTA to eb01.
the method you guys are posting seems much more logical. it sends me strait to froyo and doesnt brick my phone because it just overwrites voodoo. correct?
once voodoo is "overwritten", is it gone off my phone? if not, should i address it at all after this tutorial? froyo is downloading right now
Click to expand...
Click to collapse
Correct voodoo will be gone but you can just flash another voodoo kernel later and you can flash voodoo over voodoo just not voodoo to non voodoo with out removing it
Sent from my SCH-I500 using XDA App
efan450 said:
Yup ignore voodoo for now...when you use the atlas2.2 file in the pit section and the eb01.tar in the pda section...if repartition isn't checked make sure you check it...run it and it will bring you to stock with voodoo removed and then you can flash whatever you wanted from there...if you get stuck,p.m.me and I'll send you files with complete directions but it would have to wait till I get home from work tonight..don't panic we'll get you up and running again!
Get the newest odin, eb01. tar, and atlas 2.2pit file, and I would grab
One of the newer recovery.tar files too so when your back to stock you can flash a working recovery if you want to flash some rom after all is fixed....i recommend the 3-30 fix all recovery, but just make sure you get a tar file so you can odin it after your phone is fixed.
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
okay. I am just following what that tutorial says to do. I dont even know what a working recovery is. I never even had a rom on this thing. I have realized I am in way over my head here and have spent too much time dealing with my phone.
really all i want is to be up to date, have root, debinged/bloat, launcherpro so i dont have to use stupid touchwiz. thats basically all i need. maybe in the future i might get other stuff. but for now i think it will suit me best to just rely on verizon/samsung to keep my phone up to date and then just re root everytime. seems much simpler and safer
fupamobile said:
okay. I am just following what that tutorial says to do. I dont even know what a working recovery is. I never even had a rom on this thing. I have realized I am in way over my head here and have spent too much time dealing with my phone.
really all i want is to be up to date, have root, debinged/bloat, launcherpro so i dont have to use stupid touchwiz. thats basically all i need. maybe in the future i might get other stuff. but for now i think it will suit me best to just rely on verizon/samsung to keep my phone up to date and then just re root everytime. seems much simpler and safer
Click to expand...
Click to collapse
Recovery..clock work mod...or cwm is the recovery program you will use to install custom rom, kernels, or zip files...I will send you a p.m.later with files, info, and instructions and you can read over it and decide if you want to do it now or wait till you're a lil more familiar with the process..but for now odin the pit atlas 2.2 file and eb01 and you will be stock and be able to use launcher pro.
Sent from my SCH-I500 using XDA App

Help please. Odin won't complete flash.

I'm trying to flash stock firmware with Odin. It's stuck on factoryfs.img.
Here is what shows up on the screen:
<ID:0/009> Added!!
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> factoryfs.img
I am using the one click downloader from this link. Please tell me what I need to do to fix this. Thanks.
I found that sometimes its all in the technique of how you plug things in and the usb used. Try different usb cords. Try different usb ports. and then for some reason what worked for me is have odin open plug usb into computer, and then put the phone into download mode and finally connect the microUSB into the phone. Hope it works, hit back if it does or doesnt
[email protected] said:
I'm trying to flash stock firmware with Odin. It's stuck on factoryfs.img.
Here is what shows up on the screen:
<ID:0/009> Added!!
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> factoryfs.img
I am using the one click downloader from this link. Please tell me what I need to do to fix this. Thanks.
Click to expand...
Click to collapse
How long did you let it go for on the factoryfs.img?
It could be as simple as changing usb cable. Use the one that came with the phone. Or changing to a different usb port, preferably one directly connected to the mother board.
Beyond that, we would need to know more information about your situation. Why are you flashing stock firmware, from what condition of the phone, etc. Give as much detail as possible.
creepyncrawly said:
It could be as simple as changing usb cable. Use the one that came with the phone. Or changing to a different usb port, preferably one directly connected to the mother board.
Beyond that, we would need to know more information about your situation. Why are you flashing stock firmware, from what condition of the phone, etc. Give as much detail as possible.
Click to expand...
Click to collapse
I have tried it on all usb ports that I have on my laptop.
OK here's exactly what I did to my phone:
I downloaded the ICS version for i777 from sammobile and flashed it using ODIN. Then, I installed Siyah kernel using mobile odin. I then installed triangle away to get rid of the flash counter. I used my phone like this for a couple of days. Then today, I installed the AOKP rom. To do this, I first back up using CWM, then i booted in CWM recovery mode, did a complete wipe, deteled cache and dalvik, and then I proceeded to install the rom. Installation worked fine and everything, however the data wasn't working on my phone. So I then tried to enter the T-Mobile APN settings (it's an unlocked phone), however I couldn't save the APN settings. Tried to enter them multiple times and selected save from the menu, but it just wouldn't show up on the APN list. So, I tried to restore to my back up in CWM restore, however that failed. Admittedly, I should have asked for help at this point. However I was frustrated, so I decided to just use Odin again to flash the ICS stock firmware that I got from sammobile. However, it failed and had some error along the lines of completed writing but operation failed? I tried switching to different USB ports and restarted Odin with run as administrator, but kept getting the same error. On one of these numerous tries, I also tried to check the re-partition option just to see if that would change anything (probably not a very smart idea). Anyways, at some point during these numerous attempts, it got to the point where the phone wouldn't boot up and asked me to connect to samsung kies to restore. I tried that but my phone won't connect with kies. I then found your one-click odin stock firmware thing on these boards and used that. Tried multiple times at different ports, but it keeps getting stuck at factoryfs.img. I have left it in there for a good 30 minutes in this current try (4th). Also, this may or may not be relevant, the flash counter keeps going up.
PS: This is my first android phone so I'm pretty new at this, but I did try to read up a lot before trying anything (well, except for when I randomly checked re-partition that one time).
Edit: Sorry I should have made this clear - even though the phone will not boot, I can still get into download mode.
OK. It seems there is always AOKP in the mix somewhere, and I don't know that firmware at all well, but it seems to make some changes that are hard to fix sometimes.
Can you get into recovery mode at this point? You may still be able to depending on what has happened during the various Odin flashes. Try that and let me know, and if so what recovery do you have?
creepyncrawly said:
OK. It seems there is always AOKP in the mix somewhere, and I don't know that firmware at all well, but it seems to make some changes that are hard to fix sometimes.
Can you get into recovery mode at this point? You may still be able to depending on what has happened during the various Odin flashes. Try that and let me know, and if so what recovery do you have?
Click to expand...
Click to collapse
'
Thank you for the swift response. No, I am unable to get into recovery mode. It goes to a screen that says "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again."
I'm sort of guessing here based on information I've gleaned from various threads. You might try flashing just the siyah ICS kernel in Odin. You can download the tar for siyah 3.4.2 from here. It certainly can't make things worse at this point to try. Let me know.
While I didnt have your issues. I also recently bought an i777, my install went very smooth, everything worked more or less on the first try tried diff cords, ports and then finally it was the plug sequence that did it for me. Upon flashing AOKP, I immediately unlocked the phone via that galaxy S unlocker, I followed the steps to the T and my IMEI is still the same. I am also on tmobile, with working edge. I still have the pesky triangle, but I havent read too many good things about the triangle remover.
Perhaps you have a bad rom download? It might sound silly but flashing AOKP for a friend when I redownloaded the rom, everything worked fine. What the guy above me said, try recovery mode instead and then go from there. Good news is that your phone doesnt sound borked
creepyncrawly said:
I'm sort of guessing here based on information I've gleaned from various threads. You might try flashing just the siyah ICS kernel in Odin. You can download the tar for siyah 3.4.2 from here. It certainly can't make things worse at this point to try. Let me know.
Click to expand...
Click to collapse
Ok I tried this, and it completed successfully in Odin, however, the phone now gets stuck on the "Samsung Galaxy SII GT-I9100" screen.
But will it boot into recovery now?
creepyncrawly said:
But will it boot into recovery now?
Click to expand...
Click to collapse
No, it still does not boot into recovery.
OT: How long will I have the 5 min restriction on posting?
Also, I don't know if this is relevant, but when I try to turn off the phone, it turns off but then it'll automatically start back up within a few seconds and then get stuck on the samsung galaxy sII screen
Don't know. 10 posts?
I don't think the flash with partition checked would have caused a problem. You didn't put a path to a pit file in the pit slot did you?
The full UCKH7 firmware package should flash. Is that what you downloaded from sam firmware? You might try downloading that from the Download Repository (link in my signature) and try flashing it once again. It must be the UCKH7 stock though, because that one has the secondary bootloader and param.lfs file. The UCLE5 does not.
creepyncrawly said:
Don't know. 10 posts?
I don't think the flash with partition checked would have caused a problem. You didn't put a path to a pit file in the pit slot did you?
The full UCKH7 firmware package should flash. Is that what you downloaded from sam firmware? You might try downloading that from the Download Repository (link in my signature) and try flashing it once again. It must be the UCKH7 stock though, because that one has the secondary bootloader and param.lfs file. The UCLE5 does not.
Click to expand...
Click to collapse
No, I didn't put a pith file. Also just to make sure I'm flashing the right file, is it the one called "I777 UCKH7 stock param.lfs"?
Flash the firmware from the section titled I777UCKH7-CL503881 Stock Binaries.
You can use either the one-click downloadedr or the tar.md5 file.
Let me know if that flashes.
And also, is that the same file you downloaded from samfirmware? Because that is where this file came from. Or did you download the UCLE5 firmware from samfirmware?
creepyncrawly said:
Flash the firmware from the section titled I777UCKH7-CL503881 Stock Binaries.
You can use either the one-click downloadedr or the tar.md5 file.
Let me know if that flashes.
And also, is that the same file you downloaded from samfirmware? Because that is where this file came from. Or did you download the UCLE5 firmware from samfirmware?
Click to expand...
Click to collapse
It was the UCLE5 file. I'll try this one.
Now it gets stuck on Sbl.bin. Here is what it says:
<OSM> I777UCKH7-REV02-home-low-CL503881.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> Sbl.bin
I'll let it run for another 5 or so minutes, then I'll try different ports and see what happens.
[email protected] said:
Now it gets stuck on Sbl.bin. Here is what it says:
<OSM> I777UCKH7-REV02-home-low-CL503881.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> Sbl.bin
I'll let it run for another 5 or so minutes, then I'll try different ports and see what happens.
Click to expand...
Click to collapse
OK I tried it on all the USB ports that I have on my laptop. No luck. Still getting stuck at Sbl.bin. Any more ideas?
Yes. If it were my phone, I would start by flashing the param.lfs by itself and see if that allows it to boot, or makes progress.
If not, then I would flash the sbl.bin by itself and see if that allows it to boot, or makes progress.
If still not, then I would try the full UCKH7 package with the PIT file, and repartition checked.
You can get all the files from the Download Repository. Please bear in mind that there is risk in everything you are doing, (and have been doing.)

[Q] Soft brick

Hi,
Short story:
(My phone is a UK BTU unit - unlocked)
I was running Omega v36.
In my infinite wisdom I tried investigating hard swap. I cocked it up!
Now my i9300 sits on the Samsung GT-I9300 screen.
I can access download mode and Odin can use this
I can also access recovery mode (stock or another I can flash through Odin)
There only seems to one ROM that I can install which is a stock 3 ROM.
Upon install, it has no network or wireless connectivity.
Also on the stock recovery screen it says it cannot find \efs.
I've searched high and low, tried many different ROMS/CSC/MODEM/RECOVERY options and cannot get it to use any ROM that allows me some connectivity.
I have also tried looking for how to recover the EFS partition. I don't have a backup, BUT I do have a nandroid backup that has an efs.ext4.tar which does seem to contain the EFS folder stuff.
Can anyone help me get this thing working again?
TIA!
Can you not flash the backup of the efs folder you have?
Sent from my GT-I9300 using XDA Premium App
[email protected] said:
Can you not flash the backup of the efs folder you have?
Sent from my GT-I9300 using XDA Premium App
Click to expand...
Click to collapse
No, tried using the tar file in Odin and it crashes. It's fine with the others.
Should also mention - I have tried Kies. Flash went through, but upon reboot it was stuck at the Sammy screen again (the GT-I9300 one).
Don't know if it's relevant but I'll post it anyway
The Build number of the ROM I can get to install and run is IMM76D.I9300XXALE8
Kernel 3.0.15-554452-user
Baseband Unknown
Under status it shows
Network Unknown
Mobile network type Unknown
Service state Out of service
ERI Version Not available
IMEI Unknown
IMEI SV Unknown
Device Status Normal
adb push the EFS files back?
xSpeced said:
adb push the EFS files back?
Click to expand...
Click to collapse
That sounds like an amazing suggestion, which I havent tried.
But.....this still wouldn't solve the EFS partion missing thing...would it?
And, does anyone know where on my phone the efs folder should go? (I'm sure we all know the repurcussions of it going in the wrong place, typos etc etc)
Cheers.
First, clean the mess you (possibly) made using one of these
then, verify condition of your connections...
then, refer for further actions (if you still will have problem) here
Ok, perhaps I'm missing something here...
I don't have root access on the phone. Via USB all I can see is the default folders it lets you see.
I'm unable to connect by WiFi (thats one of the issues), so I can't download any native android apps that may help.
I CAN put stuff on the External SD card, but without having full and unlimited access to the phone memory I don't understand how I am going to copy the efs folder to where it needs to go.
I can't get any data by GSM/HSDPA, as it shows no SIM.
I have tried to flash modems but this didn't help.
Please help. I'd really like this phone to be working by the end of today (UK time )
So after flashing my phone like loads of times today, it has become apparent that pretty much everyone hosts files on hotfile so these take like forever to download and I'm still no nearer to getting full access on my phone and having a usable phone.
I tried a reverse tether, but its unable to run correctly because I dont have root (with a view to allowing me to dl some stuff to phone)
Altho I was able to install Superuser (as an apk on external SD card), I get no popup asking for su access.
This is really getting frustrating now. I cant be the only one to have this problem? I've been trying to fix this all day long
Kies/Odin/CSC/PDA/PHONE
Incidentally, Kies has only recognized the device once - that was when I did an emeregency recovery thing in it.
Otherwise it just keeps showing as connecting..........
Anyone? Ppppppplease....
It is pretty normal. KIES is conecting, bcs stupid Windows is trying to update the drivers.
When connecting to KIES, disable PC internet connection.
alternatively, write down in KIES your serial number from sticker, and download firmware prior to it.
But, honestly, if I'd be you, I'd try RESURRECTION ROM given by me in previous post.
I'm not sure if it can helps you, but it worth to have a try.
2nas.com
Provides :
1: Integrates Unbrick / Flash ROM / Root All-In-One.
2: Use the same protocol as ODIN, but 2nas is more user-friendly and easy-to-use.
3: Cloud based database to flash your android phone with correct files(ROM, etc)
4: Automatically download necessery files to flash, and check them with SHA1, it's safe for your phone.
5: Store all downloaded files in local disk, under a good directory structure, it's usefull when you have several phones.
2nas said:
I'm not sure if it can helps you, but it worth to have a try.
2nas.com
Provides :
1: Integrates Unbrick / Flash ROM / Root All-In-One.
2: Use the same protocol as ODIN, but 2nas is more user-friendly and easy-to-use.
3: Cloud based database to flash your android phone with correct files(ROM, etc)
4: Automatically download necessery files to flash, and check them with SHA1, it's safe for your phone.
5: Store all downloaded files in local disk, under a good directory structure, it's usefull when you have several phones.
Click to expand...
Click to collapse
Thanks. Software looks good and cloud downloads are amazingly fast. Trying it right now! Fingers crossed
EDIT: Well, 1st flash didn't go so well. Flashed ok, but upon reboot same problem...stuck at the Samsung GT-I9300 screen. Now trying a different firmware (strangely, the 3 one I seem to be having some luck with on Odin).
EDIT2: Managed to get that firmware installed - but still no EFS partition/folder so no connectivity.
EDIT3: I DO LIKE THAT SOFTWARE THO. Very nice 2nas!
EDIT4: Ok, after much messing I managed to get my EFS folder back. It still wont let me connect to a network, although it does show networks. I also still cannot connect to a WiFi (my own!). Every time I reboot the phone, the EFS folder gets deleted and I have to copy over again. So guys, over to you...any ideas?
Well, good news.... :victory:
I flashed and rooted using 2nas software. Very good it is! I recommend it to newbs wanting to root.
As stated in 1st post, I had a copy of my EFS folder in a efs.ext4.tar.
After much messing about involving me having to copy over the EFS folder several times and sometimes it working and others it not...
I saw someones post about baseband (in S3 case Modem/CSC). I flashed one of each through Odin.
It went into Factory mode (dunno what that was about)...I copied over my EFS folder...and voila...network running...IMEI restored....
I still dont seem to be able to get Wifi...but thats a minor niggle...I'm on an unlimited data plan anyway...fortunately.
I've yet to reboot to see if the EFS folder sticks...but at least I now know I can get it to a working condition-ish. There must be some dev's here who know the answer to that one..
So a huge warning to all....make sure you have multiple copies of your EFS folder...it's saved me!! :good:
Now, gotta go see if I can get that Wifi working...
Thanks....a great community here.
Oh, first thing I'm doing....taking another backup of that EFS folder!!!
Well taken from a post of kocweb
kocweb said:
Here is the exact solution for this problem which i have recently had!
You have to root your phone and install Terminal Emulator from Google Play.
Open terminal emulator and type as ;
su
rm /efs/FactoryApp/keystr
rm /efs/FactoryApp/factorymode
echo -n ON >> /efs/FactoryApp/keystr
echo -n ON >> /efs/FactoryApp/factorymode
chown 1000.1000 /efs/FactoryApp/keystr
chown 1000.1000 /efs/FactoryApp/factorymode
chmod 0744 /efs/FactoryApp/keystr
chmod 0744 /efs/FactoryApp/factorymode
reboot
You now should not see the that message anymore. Its because of an EFS corruption. ( Thanks to yesilcin*com (sawgent) ) for exact solution.
Hope it helps!!!
Click to expand...
Click to collapse
So it seems the EFS folder install is fixed. I should mention I installed HC-kTool to restore EFS folder from my efs.ext4.tar which I placed in /sdcard on my phone (thats the internal memory, and where you end up if you connect to your PC with USB cable)
Thanks guys.....now...dare I reflash with Omega v39...
Hi all!
Thats my first post, i comming from swizerland, and my english is not good!! sorry for that! :angel:
I think i have the same problem but a bit difrent. i have translate my question with google hope that works and you understand it:
Hi all.
'm New here, please little indulgence if I'm doing something wrong: o)
Have unfortunately a boat trailer in the process
Mobile: Galaxy S3
Wanted to put on my cell phone that is flashed via odin this new FW:
I9300XXELL4_I9300AUTELK2_I9300XXELL4_HOME.tar.md5
Everything without problems, CF root on it, not a problem.
Then Triangle instaled away, not a problem.
I saw the EFS should secure their first choice, this Ktool downloaded (play store).
backed up, but nothing was available (I think becouse partion is named "sdcard0" and not "sdcard" (??))
Ok then I have a root folder app downloaded wanted sdcard0 change in sdcard but dosn`t work..
Then I wanted to check Ktool, the difrent funtions and am accidentally come to "ESF format" (in german "format is like *avi*, *mkv* *wmv*and have also confirmed this ..
Result -> phone stops at the boot logo.
New flash via Odin tried but without success.
factory reset and reset cache on Recovery also without success.
Half the south death I think I'm not. Since model name in the download mode available.
Luckily I have a backup of EFS i think from omega rom on my sd ext:
efs_01Oct2012-1028.tar.gz
when i open it with 7zip i have that: efs_01Oct2012-1028.tar
open it again then that :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Can i flash it with Odin? when yes where must i put it in? "PDA" , "CSC" , "PHONE" ?
I'm not sure if it can helps you, but it worth to have a try.
2nas.com
Provides :
1: Integrates Unbrick / Flash ROM / Root All-In-One.
2: Use the same protocol as ODIN, but 2nas is more user-friendly and easy-to-use.
3: Cloud based database to flash your android phone with correct files(ROM, etc)
4: Automatically download necessery files to flash, and check them with SHA1, it's safe for your phone.
5: Store all downloaded files in local disk, under a good directory structure, it's usefull when you have several phones.
Click to expand...
Click to collapse
I tried that out but become that:
In recovery I can`t mount my sdcard (maybe because its named sdcard0?)
Edit: installed from internal_sd and external card I can choose.
i hope i said the most usful to help me .
and sorry for my english!! (half is from google )
thx and gretings from swizerland
EDIT: Okey i have flashed now 3part firmware with pit file : I9300XXALE8_I9300OJVALE7_OJV now i can boot!!! ....but only boot... now i ned help to fix my EFS ;o)
Follow the steps I posted in my earlier threads...first thing you'll need to do is root your phone though.
I was lucky as I had some .apk files around which helped. You may need to search on the forum or otherwise.
To help you, heres what I used
Ariza Patch - can be found on forum
Superuser - can be found in something called Galaxy SIII Firmware Downloader
root explorer - unsure where this came from (any kind of explorer will do)
Busybox - unsure where my copy came from, but can be found around and on Play store
Android Terminal - can be found on Play store.
First thing...root your device
second extract your backed up /efs folder to the folder called /efs on your phone memory.
Try Wifi. It may work. If it does, you can get any other apps you need on Play store.
Once you've copied the files, open your android terminal and follow the last part of my previous post.
That should get you up and running.
Good luck.
thx IRPnet for your post!
but problem is now, after the "working" firmware i have flashed an other firmware "german" and after that... again bootloop!! :crying:
no i have trided difrent 3 parts firmware with pit file (GT-I9300_mx_20120329 and GT-I9300_mx_20120322) with odin3 v1.85, Odin 3 v3.04 and Odin 3 v3.07 but dosend work.
on this firmware : "I9300XXALE8_I9300OJVALE7_OJV" with Odin3 3.04 and GT-I9300_mx_20120329.pit i have that fail :
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXALE8_554452_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXLE8_REV02_REV04_CL1145430.tar.md5 is valid.
<OSM> CSC_OJV_I9300OJVALE7_CL547448_REV00_user_low_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Set PIT file..
<ID:0/010> DO NOT TURN OFF TARGET!!
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> sboot.bin
<ID:0/010> NAND Write Start!!
<ID:0/010>
<ID:0/010> Complete(Write) operation failed.
<ID:0/010> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
when i want to flash that : I9300XXDLJ5_I9300XXDLID_I9300DBTDLI2 with same pit and same Odin that :
<ID:0/010> Added!!
<ID:0/010> Removed!!
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Set PIT file..
<ID:0/010> DO NOT TURN OFF TARGET!!
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> boot.img
<ID:0/010> NAND Write Start!!
<ID:0/010> param.bin
<ID:0/010> recovery.img
<ID:0/010> sboot.bin
<ID:0/010>
<ID:0/010> Complete(Write) operation failed.
<ID:0/010> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
...
i have also that firmware from this tread: I9300XXELLA_KOR_MULTI_FACTORY
this is inside :
BOOTLOADER_I9300XXELLA_742798_REV00_user_low_ship.tar.md5
CODE_I9300XXELLA_742798_REV00_user_low_ship.tar.md5
CSC_I9300OXAELLA_742798_KOR_FACTORY_user_low_ship.tar.md5
MODEM_I9300XXELLA_742798_REV00_user_low_ship.tar.md5
mx.pit
Click to expand...
Click to collapse
i can flash that! but it dosent start (after boot its doing some things with the little android men and the "samsung galaxy s3" is coming but nothing else... )
i could cry... dam it.... need al the help...
Edit: Coult it be my phone dosn`t boot becouse the "efs" is lost?....
After you have used Odin, are you going going into recovery and doing a wipe?
You need to WIPE/FACTORY RESET and then WIPE CACHE.
Your phone should then boot up
Try that, let me know how you get on.
I'm no expert on these things, so if someone else wants to join in this thread...feel free.
I can only relate to my experience. Although your experience does sound similar.
IRPnet said:
After you have used Odin, are you going going into recovery and doing a wipe?
You need to WIPE/FACTORY RESET and then WIPE CACHE.
Your phone should then boot up
Try that, let me know how you get on.
I'm no expert on these things, so if someone else wants to join in this thread...feel free.
I can only relate to my experience. Although your experience does sound similar.
Click to expand...
Click to collapse
after wipe/factory reset shoult i restart to recovery or do the wipe cache without reboot to recovery?
i doing that without reboot to recovery but no chance... still the same...
in recovery it also says : E:failed to mount /efs (Invalid argument) --> like i said.. no efs in my phone..
You can do both at the same time. It should then reboot.
Don't worry about the error...that will show until you got it recovered.
You've got to get the phone booting correctly before you can restore the EFS partition from your backup.
Once the phone boots up, you may find that with your SIM inserted you get no phone signal - it might even say that you have no SIM inserted. You will also not be able to get Wifi. Thats why you need the apk's for the software I mentioned on your external SD card.
Now, if you know how to use adb you can push them with that (if you know how, I don't).
If the phone boots correctly, your PC should see it and you SHOULD be able to copy files.
Thats the important part.

Can't unbrick phone (stuck in odin mode)

Hi,
I've got this problem with a friends(girl) phone.
Her phone was stuck at the firmware upgrade screen(the one with firmware upgrade encountered an issue). So she searched the internet for a solution and did some things with kies and odin. But nothing worked so i offered to help her.
So i searched and found this article. i followed all the instructions and downloaded 3 different versions of odin V3.07, V1.3 and V1.85.
Specifications of the phone:
samsung Galaxy S II GT-I9100 16GB
what i've tried so far:
i followed the instructions from te link above and tried it with the following roms
-I9100GXXLB1_I9100GATOKL1_ATO
-I9100XWLP9_I9100KPNLP1_KPN
-I9100XXLSJ_I9100OXXLS1_OXX
i also tried the gingerbread and the ICS version
i also tried the pit file. but nothing works, the progress get stuck like in this example
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GXXLB1_I9100GATOKL1_I9100GXXKL4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> cache.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone help me with this problem? I also have a JTAG programmer but don't know how or what to do with it.
Check out this guide:
http://forum.xda-developers.com/showthread.php?t=2345831
Look for hopper8's thread.
And stop flashing pit files.
Sent from the little guy
Ok, i've followed every step but the phone is still bricked.
i've noticed something else: i've tried some different packages and versions of odin, and when in download mode on the phone the custom binary download is saying Yes(5 counts) en the Current binary is changing from custom to samsung stock back and forth.
Basseytje said:
Ok, i've followed every step but the phone is still bricked.
i've noticed something else: i've tried some different packages and versions of odin, and when in download mode on the phone the custom binary download is saying Yes(5 counts) en the Current binary is changing from custom to samsung stock back and forth.
Click to expand...
Click to collapse
I updated the OP today, with an extra option for i9100 (which you have). It's flashing JB leak (stock ROM, 3 part firmware) via Odin, which will wipe your device as it flashes. Give it a go.
when u go to download mode, does it show your model number??
Hopper8 said:
I updated the OP today, with an extra option for i9100 (which you have). It's flashing JB leak (stock ROM, 3 part firmware) via Odin, which will wipe your device as it flashes. Give it a go.
Click to expand...
Click to collapse
I've already tried that one but odin is stuck at data.img.
tornado92 said:
when u go to download mode, does it show your model number??
Click to expand...
Click to collapse
Yes it shows the product name.
Basseytje said:
I've already tried that one but odin is stuck at data.img.
Yes it shows the product name.
Click to expand...
Click to collapse
then you can fix it by flashing i guess .. try different versions of odin/try different usb ports/ different usb cables/ different pc/ :fingers-crossed:
tornado92 said:
then you can fix it by flashing i guess .. try different versions of odin/try different usb ports/ different usb cables/ different pc/ :fingers-crossed:
Click to expand...
Click to collapse
i've tried several cables, 2 pc's, one laptop, all the ports, all the versions of odin, 6 different roms
Basseytje said:
i've tried several cables, 2 pc's, one laptop, all the ports, all the versions of odin, 6 different roms
Click to expand...
Click to collapse
it could be problem with your internal memory then... can u post a photo of your download mode.. what errors you get when u do a factory reset using recovery??? also when your phone is bricked dont try to unbrick using a custom rom or kernals because it can cause drawbacks like corrupting efs and all.. always try to unbrick using a stock firmwares.. also dont use pit immediately .. keep it for the last try...
also make sure kies and other tools are not running on backgroup ,, unistall them and reinstall samsung drivers and try again..
tornado92 said:
it could be problem with your internal memory then... can u post a photo of your download mode.. what errors you get when u do a factory reset using recovery??? also when your phone is bricked dont try to unbrick using a custom rom or kernals because it can cause drawbacks like corrupting efs and all.. always try to unbrick using a stock firmwares.. also dont use pit immediately .. keep it for the last try...
also make sure kies and other tools are not running on backgroup ,, unistall them and reinstall samsung drivers and try again..
Click to expand...
Click to collapse
kies won't recognize the phone. the only 3 screens i can access are showed in the pics below. i've got 2 stock roms which don't work. after i tried kies, i immediately uninstalled it and left the drivers on the pc.
i40.tinypic.com/29gkdi1.jpg
i40.tinypic.com/qsnluc.jpg
i41.tinypic.com/2aep3yx.jpg
can't post any files yet.
I hope there is still someone who can help me...
odin is still stuck on data.img
If you say you've 'tried everything' (which everyone always says), then it's a service centre job. What else do you want anyone here to say ? No miracle fixes. If it were me I'd keep trying, it's almost always something really simple/small/obvious that's causing the flash not to work, and as we're not there looking over your shoulder at what you're doing, it's going to be almost impossible for anyone to say what that is (you have 'tried everything' after all).
is there a way to fix this with jtag?
Basseytje said:
is there a way to fix this with jtag?
Click to expand...
Click to collapse
Maybe. No one can say for sure mate. If you motherboard is really borked, it would have to be replaced nevertheless.
Remember that Jtagging leaves marks on your device, so you can kiss goodbye any warranty u might have.
"To err is human, to forgive is divine."
Sent from my SGS II
hey.. i had this problem too.. the only solution that i had is to use the galaxy note pit file and a stock rom for i9100 ... then the phone went back to normal ..but the memory went from 16 tb to 11.5 gb .. it was the only thing that made my phone work again..
i installed pit from galaxy note ..with and original stock firmware 4.1,2 then after install I did a factory reset via stock cwm and a clear cache ..and it worked.. a few bootloops and it went on:|
alexandru.j91 said:
hey.. i had this problem too..
Click to expand...
Click to collapse
You got so ridiculously lucky that I can't comprehend that it worked. Please don't advise others to do the same, I'd say what you did is normally a recipe for a hard brick. Don't flash files for other phones, let alone a pit file for another phone. Yes I know the note has the same hardware as i9100 but you know what? It's not an i9100.
Edit: Look at what you posted in your other thread:
alexandru.j91 said:
I hardbricked my phone about 3 months ago with the original firmware from orange 4.0.4 and I resolved the problem by putting samsung note PIT file ..but I don't have acces to all the memory on my phone ..I have almosst 12 gb from 16.. and my phone is getting wired ..and it is shutting off randomly since then .and to get it on again i have to remove the battery ..
Does anybody know how to get all my memory back for my phone? tx
Click to expand...
Click to collapse
I'd say that's a reason not to flash files from another phone.
i was just telling him that i had the same problem..not to do the same thing..because of the problem that I have got! i have told in my other post whathappened to my phone! and i know that my problem can be solved by rewriting the memorybut i don't know how!..
---------- Post added at 06:04 AM ---------- Previous post was at 05:05 AM ----------
what I did.. i did because of some threads on xda ..so I am not crazy ..I just told him what I have did.. I haven't advised him to do that ..because of the problem that i had .. and when I wrote what I have did to make my phone worked .. i hace told the fact that it shrinked my memory from my phone..
maybe i'm getting a little progress. when i try to flash a new bootloader. i see a progress bar on the phone. but odin is halfway stuck at sbl.bin
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> boot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> Sbl.bin
everywhere i read, people are saying use different cables. i already tried the samsung s2 cable, a htc desire cable, 3 deal extreme cables and an other htc(dont remember the model) cable. but i'm getting the same problems. stuck at zimage or something else...
anyone?

[Q] Samsung Galaxy S II I9100G not going to Download Mode or Recovery Mode

Hi
I am in a serious trouble.
I am having a Samsung Galaxy S2 GT-I9100G
Its running on Stock Rom JB v4.1.2
I wanted to update it to Kitkat 4.4.2 by CyanogenMod 11 Custom Rom.
In order to do that i have rooted my phone using VRoot.
Installed CWM Recovery 6.0.1.2
Copied the ROM files and Gapps to SD Card.
Done all the prerequisite and started installing the ROM.
Then the installation failed showing Error Status 7.
Upon googling about status 7 i got to know that the CWM Recovery 6.0.1.2 which i used doesn't support for
installing CM11.
Then i searched for the latest CWM Recovery and got to know about the Philz CWM Touch Recovery 6.0.4.5
I also got to know that in order to install Philz CWM Touch Recovery 6.0.4.5 you need to have a PC with Odin
v3.09 installed to flash this latest CWM Recovery.
Then i downloaded philz_touch_6.19.3-i9100g.tar.md5.
Installed Odin v3.09 in my PC.
Gone into Download mode by pressing Home + Volume Down + Power Button then warning screen came up then by
pressing volume up i came into download mode.
Then i connected my device to PC using USB cable. I got the added message. I also got the COM Port number.
But instead of Yellow as said in the tutorial i got Light Blue Color which i ignored. I thought the Odin
software might had made any changes to their software.
I clicked the AP button and selected the TAR file downloaded then clicked the START button.
Again failed. I don't know why that happened.
I removed the USB cable and reinserted then done the same. Then some message came and process is going on...
waited for 20 mins till nothing was happening.
Fed up of all the process i removed the USB cable thinking of forgetting Kitkat and use the stock rom.
After removing the USB cable suddenly a message flashed on the screen.
Firmware update encountered an issue. Please select recovery mode in Kies & try again.
Whatever i do only this is appearing on screen.
Nor it's going into Download Mode or Recovery Mode.
Please help me in recovering my phone to Stock ROM or Custom ROM.
Last hope is jig. It force download mode when.you cant by pressing buttons. If this doesnt help i think that your phone is now a clip for paper. In odin you should choose pda and after that choose kernel. I never had blue sign in odin but i had i9100. You should from the beghinig try philz kernel to root amd get cwm recovery. So as i sad you must try jig usb very cheap thing or you can do it by yourself. Maybe you should either try kies and kies recovery firmware.
Wysłane z mojego D5503 przy użyciu Tapatalka
adithyagem said:
After removing the USB cable suddenly a message flashed on the screen.
Firmware update encountered an issue. Please select recovery mode in Kies & try again.
Whatever i do only this is appearing on screen.
Nor it's going into Download Mode or Recovery Mode.
Click to expand...
Click to collapse
Here's where your problems are.
1. Never unplug your cable during an Odin flash. Wait till it fails. Else you'll get trouble, guaranteed.
2. You're in forced download mode. Flash a Stock ROM using Odin while it says 'firmware update encountered an issue'.
3. Instead of using Odin with Philz, next time you can just flash Philz directly from the external SD card (at least on i9100, not sure about the i9100G). Much easier.
Regarding the blue in Odin, I'm pretty sure that's OK. I've seen reports of other people getting blue instead of yellow. I've always had yellow myself but wouldn't hesitate to flash if it was blue.
Newer versions of Odin have blue in the ID:COM field.
Done as said by you
Hopper8 said:
Here's where your problems are.
1. Never unplug your cable during an Odin flash. Wait till it fails. Else you'll get trouble, guaranteed.
2. You're in forced download mode. Flash a Stock ROM using Odin while it says 'firmware update encountered an issue'.
3. Instead of using Odin with Philz, next time you can just flash Philz directly from the external SD card (at least on i9100, not sure about the i9100G). Much easier.
Regarding the blue in Odin, I'm pretty sure that's OK. I've seen reports of other people getting blue instead of yellow. I've always had yellow myself but wouldn't hesitate to flash if it was blue.
Click to expand...
Click to collapse
I tried flashing Philz CWM Recovery using Odin while firmware update encountered an issue screen flashing on screen
Again it failed showing this Log
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.19.3-i9100g.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can you tell me where i gone wrong!?!!
adithyagem said:
I tried flashing Philz CWM Recovery using Odin while firmware update encountered an issue screen flashing on screen
Again it failed showing this Log
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.19.3-i9100g.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can you tell me where i gone wrong!?!!
Click to expand...
Click to collapse
Why did you flash Philz? I said to flash a stock ROM with Odin, not flash Philz.... Click the Odin link in my signature and you can find a 3-part firmware, which will wipe as it flashes. DO NOT flash the 3-part firmware, you have an i9100G. You need to download a stock ROM from Samfirmware or similar. Instructions are in the thread. If it fails again, then follow all of the troubleshooting steps. Keep flashing till you get a successful flash. There's nothing else you can't try which is in that thread, so keep at it.
Edit: Stop. There is no Philz kernel for i9100G. Why on earth did you flash it? It only exists for i9100. Not the 'G' variant. What to do from here? Flash a stock ROM via Odin, like I said to start with, make sure it's for an i9100G.
However, now that you've unplugged the cable during a flash, and flashed the wrong file at least twice, I'm not holding out high hopes for your phone recovering from this.
The ability of people to read & comprehend the help they've been given here & then actually do what's been suggested seems to get worse & worse as time goes by.
Give some very specific advice (step by step stuff, or refer them to step by step stuff), they go do something completely different. I mean, if that's going to happen, why bother asking for help in the first place ?
@MistahBungle, read the edit on my previous post (if you haven't seen it already). Do you agree the only chance is a stock ROM? I don't know, I don't see many this stuffed up very often.
Edit: Unless, there is a Philz for i9100g. But I can't find an XDA thread for it just by having a cursory glance.
Yep. Flashing a stock rom & praying is pretty much the only option. Classic case of 'attempting to do without learning'. Imagine how much **** these people would be in if the half dozen of us or so who post most of the useful help here decided to move on ?
I did find Philz for i9100g, but it's ages old (newest one I could find was 6.19.3, think Philz is up to 6.30.something). There's also no xda thread for it, so I'm tipping that the i9100 version has been flashed. Still not holding high hopes even with a correct stock ROM.
I know, there's less people here than when I started by a long shot. You're by far the most active on here, but I thought you had an S4? I'll be getting the N5 in a month or so. I still plan to be in S2 threads but obviously to a lesser extent.
I do have an S4, but apart from the first couple of months, lost interest in modding it. I want stuff to 'just work' these days for the most part. I do run a custom rom/kernel, I just haven't changed it in ages & not interested in anything that trips Knox. Just can't be bothered putting up with stuff not working/spending a lot of time trying to make it work.
So...I accumulated a lot more knowledge of the S2, given I spent 18 mths or so actively modding it.
Understood. Yes that's what seems to be happening more now, phones which, if they're not on stock ROM, lose a lot of functionality/have stuff 'not work' for whatever reason. Like the GNote & its S-pen, HTC One and boomsound, Sony and its Bravia engine. I assume you still own the S2 anyway...
While you're here, is there anything in the Odin troubleshooting guide you've noticed which should be changed? I read over it again the other day but couldn't see anything major. If you don't want to read/comment no problem, asking as you're the resident Odin guru.
Yeah still have the S2. Haven't switched in on in 6 mths tho.
Nah, you've got everything covered in your thread. It's a great resource ('Odin expert' ? Hardly. I just read/learned a lot )
Mmm I imagine it's not the greatest experience after using a phone 3yrs newer for a while Cool. I added a couple little things just now (another pit file thread (shudder) which is quite well done & re-hosted the 3-part firmware instead of dropbox. Nothing special). Ok, call yourself what you want but what I'm sure of, is that by being on Q&A so much you have a lot more troubleshooting knowledge than probably anyone else for S2
Hopper8 said:
Why did you flash Philz? I said to flash a stock ROM with Odin, not flash Philz.... Click the Odin link in my signature and you can find a 3-part firmware, which will wipe as it flashes. DO NOT flash the 3-part firmware, you have an i9100G. You need to download a stock ROM from Samfirmware or similar. Instructions are in the thread. If it fails again, then follow all of the troubleshooting steps. Keep flashing till you get a successful flash. There's nothing else you can't try which is in that thread, so keep at it.
Edit: Stop. There is no Philz kernel for i9100G. Why on earth did you flash it? It only exists for i9100. Not the 'G' variant. What to do from here? Flash a stock ROM via Odin, like I said to start with, make sure it's for an i9100G.
However, now that you've unplugged the cable during a flash, and flashed the wrong file at least twice, I'm not holding out high hopes for your phone recovering from this.
Click to expand...
Click to collapse
Thanks Hopper for the help...
I have downloaded the Stock ROM for GT-I9100 Indian Version from Sammobile. I don't know what is 3-part firmware.
Now what i am going to do is Connect the phone to my PC showing (Firmware update encountered an issue. Please select recovery mode in Kies & try again) screen.
Then by clicking AP button selecting the TAR file extracted from the Zip file (Stock ROM).
Double check that only AUTO REBOOT & F.RESET TIME checkboxes are selected.
Hit Start and try my luck.
Shall i go ahead. Waiting for your nod...
*nod*
Edit - Hang on, I hope you downloaded I9100G firmware. If you downloaded I9100 Indian firmware, don't flash that.
MistahBungle said:
*nod*
Edit - Hang on, I hope you downloaded I9100G firmware. If you downloaded I9100 Indian firmware, don't flash that.
Click to expand...
Click to collapse
I have downloaded I9100G firmware only...
sorry it was my typing mistake
really sorry to panic you
I have also got a DLL file in the ZIP which i have downloaded. What is it?
Throw the .dll away, you don't need it.
Thanks to Hopper8
Hopper8 said:
Why did you flash Philz? I said to flash a stock ROM with Odin, not flash Philz.... Click the Odin link in my signature and you can find a 3-part firmware, which will wipe as it flashes. DO NOT flash the 3-part firmware, you have an i9100G. You need to download a stock ROM from Samfirmware or similar. Instructions are in the thread. If it fails again, then follow all of the troubleshooting steps. Keep flashing till you get a successful flash. There's nothing else you can't try which is in that thread, so keep at it.
Edit: Stop. There is no Philz kernel for i9100G. Why on earth did you flash it? It only exists for i9100. Not the 'G' variant. What to do from here? Flash a stock ROM via Odin, like I said to start with, make sure it's for an i9100G.
However, now that you've unplugged the cable during a flash, and flashed the wrong file at least twice, I'm not holding out high hopes for your phone recovering from this.
Click to expand...
Click to collapse
Thank You so much
I got my phone back to the original state:laugh:
Thank You so much for your help...
...

Categories

Resources