I would like to flash a new rom. i am currently rooted. I would like to be able to use the nfc feature, as well have jellybean installed. i was looking at using this rom: http://forum.xda-developers.com/showthread.php?t=1574718. it mentions cwm. is this ok to install on my phone? also, any guidance with this would be great!
Yes its fine
Sent from my SGH-I777
Add long as your phone is an i777, you follow the instructions on the OP, and you re-wipe and flash before asking about something messing up... Yes.
I would also recommend flashing aokp 7.3 ICS, then flashing the JB ROM. It seems to be helpful.
Clay
Team Pirate
Sent from my Buttery Smooth PINK SGH-i777
OP don't forget to hit the thanks button to those who have helped you.
Sent from Team Pirate
sniper8752 said:
I would like to flash a new rom. i am currently rooted. I would like to be able to use the nfc feature, as well have jellybean installed. i was looking at using this rom: http://forum.xda-developers.com/showthread.php?t=1574718. it mentions cwm. is this ok to install on my phone? also, any guidance with this would be great!
Click to expand...
Click to collapse
Our phones have a recovery built into the kernel so make sure not to try and flash anything with Rom Manager.
Sent from Team Pirate's secret underground base
sniper8752 said:
I would like to flash a new rom. i am currently rooted. I would like to be able to use the nfc feature, as well have jellybean installed. i was looking at using this rom: http://forum.xda-developers.com/showthread.php?t=1574718. it mentions cwm. is this ok to install on my phone? also, any guidance with this would be great!
Click to expand...
Click to collapse
If you start off using any custom ROM, especially the AOKP, I do suggest you spend time read more, follow that thread (the link you provided), the more you read the more you save time and avoid headache down the road. One example that Phalanx just pointed out, it isn't listed anywhere but from reading and following that thread.
1. Make sure your device is i777, if anything other than that, stop.
2. Make sure you have the CwM Recovery installed. Do get along with the buttons such what home button does, what power button does. It depends on the CwMR version.
3. Follow the instruction of the ROM for installation.
4. Good luck and enjoy.
I have cwm installed, and I select the option in the app to reboot into recovery. it reboots, and goes into recovery mode. the only problem is, is that it is the android system recovery. I do not see an option for backup there.
sniper8752 said:
I have cwm installed, and I select the option in the app to reboot into recovery. it reboots, and goes into recovery mode. the only problem is, is that it is the android system recovery. I do not see an option for backup there.
Click to expand...
Click to collapse
For crispy sake don't use Rom manager!
Read more before flashing anything
Raise yer mizzenmast and swab 'er poop deck!
sniper8752 said:
I have cwm installed, and I select the option in the app to reboot into recovery. it reboots, and goes into recovery mode. the only problem is, is that it is the android system recovery. I do not see an option for backup there.
Click to expand...
Click to collapse
Luckily you don't have CWM installed yet using Rom Manager what you have is Rom Manager....
1. Uninstall Rom Manager ASOP
2. You need to flash a custom kernel to get CWM you can do that be installing Mobile Odin lite free from XDA and flashing a kernel...
3. You need to read LOTS more or you risk BRICKING your phone......
4. It will depend what ROM your on now what kernel you need to flash to get CWM Gingerbread = GB kernel ICS = ICS kernel PLEASE read before doing ANYTHING............
5. Go to this link and READ 3a. http://forum.xda-developers.com/showthread.php?p=18576627#post18576627
snipe2nite said:
Luckily you don't have CWM installed yet using Rom Manager what you have is Rom Manager....
1. Uninstall Rom Manager ASOP
2. You need to flash a custom kernel to get CWM you can do that be installing Mobile Odin lite free from XDA and flashing a kernel...
3. You need to read LOTS more or you risk BRICKING your phone......
4. It will depend what ROM your on now what kernel you need to flash to get CWM Gingerbread = GB kernel ICS = ICS kernel PLEASE read before doing ANYTHING............
5. Go to this link and READ 3a. http://forum.xda-developers.com/showthread.php?p=18576627#post18576627
Click to expand...
Click to collapse
i noticed there is only mobile odin pro now? any free solutions? and so with this, i can flash my rom?
sniper8752 said:
i noticed there is only mobile odin pro now? any free solutions? and so with this, i can flash my rom?
Click to expand...
Click to collapse
No. The lite version is still in the OP of the developers thread as an attachment.
sniper8752 said:
i noticed there is only mobile odin pro now? any free solutions? and so with this, i can flash my rom?
Click to expand...
Click to collapse
I will help you get this working, I have some questions tho to get you the right info when you see this respond back just don't do anything till
I help you.... I would rather help you then have you brick your phone but of course do whatever you want.... You can DL and install these 2 files just like any other apk install MobileODINLite first then FlashKernel I777 of course you will need to be rooted, this wont change anything on your phone it will just install the app to get you ready to flash the zImage... The next step is KEY as to what you're running now.... That's where I have questions...
https://www.dropbox.com/s/xxf4c4tvevh1gnx/MobileODINLite-v3.25.apk Here is a link to the latest release from my dropbox.
https://www.dropbox.com/s/5q4b5tkmxsdx0e1/Mobile ODIN FlashKernel I777.apk FlashKernel I777
EDIT I will be around here for about 3 hours it's 6:40am now on the west coast after that it will be like 10 hours...
got it. why does odin need my location?
also, it says that odin required an add-on to be able to flash firmwares on the device (i think i just figured it out... was that the second thing i installed?).
thanks for your help! i appreciate it.
sniper8752 said:
got it. why does odin need my location?
also, it says that odin required an add-on to be able to flash firmwares on the device (i think i just figured it out... was that the second thing i installed?).
thanks for your help! i appreciate it.
Click to expand...
Click to collapse
I'm not sure why the location permission BUT it is built by 1 of the best devs on here ChainFire nothing to worrie about....
the second file was the add-on, when you load mobile odin is it saying you need to install the add-on? Now you need to flash the zImage to get CWM if you haven't already....What firmware are you on now? I feel dumb telling to flash the 2nd file you only need the Odin lite to flash the zImage (kernel) to get CWM once you flash a new ROM in CWM you will lose all the data anyways... Now that you have um back them up and save them so when you flash a new ROM you can reinstall both of them!! Always good to have IMO...
snipe2nite said:
I'm not sure why the location permission BUT it is built by 1 of the best devs on here ChainFire nothing to worrie about....
the second file was the add-on, when you load mobile odin is it saying you need to install the add-on? Now you need to flash the zImage to get CWM if you haven't already....What firmware are you on now? I feel dumb telling to flash the 2nd file you only need the Odin lite to flash the zImage (kernel) to get CWM once you flash a new ROM in CWM you will lose all the data anyways... Now that you have um back them up and save them so when you flash a new ROM you can reinstall both of them!! Always good to have IMO...
Click to expand...
Click to collapse
I have installed both apks. zimage has to do with the bootup, right? where do i get that file? would the firmware be i777ucle5?
@sniper8752,
You seem to be flailing around in the dark. You really need to not only read, but also see how things fit together. Just a friendly warning, if you don't know what a zImage is, or why you are flashing it, or which zImage to use, you still need to do some more reading and get a better overall picture before you continue with flashing JellyBean.
The zImage is the kernel. (Don't forget to capitalize the I as linux is case sensitive.) I am assuming you are rooted but do not have ClockworkMod Recovery installed yet. You need to install a custom kernel that matches your system. That means flash a Gingerbread kernel if you currently have a Gingerbread system, or an ICS kernel if you currently have an ICS system. The various options for the kernels are available in the development section. To use a zImage with mobile odin, you must extract the zImage from the .zip file (or sometimes .tar) that the developer makes available. Mobile odin can actually pull the kernel from a tar file, but it will not recognize a zip file.
creepyncrawly said:
@sniper8752,
You seem to be flailing around in the dark. You really need to not only read, but also see how things fit together. Just a friendly warning, if you don't know what a zImage is, or why you are flashing it, or which zImage to use, you still need to do some more reading and get a better overall picture before you continue with flashing JellyBean.
The zImage is the kernel. (Don't forget to capitalize the I as linux is case sensitive.) I am assuming you are rooted but do not have ClockworkMod Recovery installed yet. You need to install a custom kernel that matches your system. That means flash a Gingerbread kernel if you currently have a Gingerbread system, or an ICS kernel if you currently have an ICS system. The various options for the kernels are available in the development section. To use a zImage with mobile odin, you must extract the zImage from the .zip file (or sometimes .tar) that the developer makes available. Mobile odin can actually pull the kernel from a tar file, but it will not recognize a zip file.
Click to expand...
Click to collapse
I have decided on flashing this rom: http://ultimatum.us/. looks like it will take about an hour to download... i currently have ics installed. to flash the zImage, do I click on "Kernel" in the app.?
thanks for help and explaining the zImage. what would be the best way to learn all of this? is there a good site so I don't have to go looking around everywhere? maybe like a beginner's guide?
sniper8752 said:
I have decided on flashing this rom: http://ultimatum.us/. looks like it will take about an hour to download... i currently have ics installed. to flash the zImage, do I click on "Kernel" in the app.?
thanks for help and explaining the zImage. what would be the best way to learn all of this? is there a good site so I don't have to go looking around everywhere? maybe like a beginner's guide?
Click to expand...
Click to collapse
Dude, you are so far off path. there are no "begginers" guides, just what we got. Honestly, this stuff aint for you man. dont mess with your phone.
but if you insist, then just keep reading.
sniper8752 said:
I have decided on flashing this rom: http://ultimatum.us/. looks like it will take about an hour to download... i currently have ics installed. to flash the zImage, do I click on "Kernel" in the app.?
thanks for help and explaining the zImage. what would be the best way to learn all of this? is there a good site so I don't have to go looking around everywhere? maybe like a beginner's guide?
Click to expand...
Click to collapse
What app? There is no app...
ClockWorkMod Recovery (CWM) yes, app NO.
EDIT: Just realized you may be talking about mobile Odin our three cwm app. Don't use either at this print, much easier using CWM (reboot into recovery of you've got a custom ROM/kernel)
Clay
Team Pirate
Sent from my Buttery Smooth PINK SGH-i777
so i should use cwm instead of odin? i thought people were telling me not to use cwm?
Related
Hello everyone, Im truly at a loss...
ive been going at this for weeks reading countless threads and differnt sites and i cant figure it out...
My at&t is rooted.. i do have super user access and rom manager installed..
the only problem is when i go into rom manager and reboot into recovery or try to flash a rom i get an error...
e: fialed to verify whole file signature
e: signature verification failed
installation aborted..
it is the blue screen and not the recovery orange screen.... why isnt my recovery not installed and how do i install it??
please help..
if you need any info please let me know thank you..
kind of difficult to understand what you're actually asking, btw the cwm recovery is not orange it's lightblue. also, DON'T USE ROM MANAGER
Nick281051 said:
kind of difficult to understand what you're actually asking, btw the cwm recovery is not orange it's lightblue. also, DON'T USE ROM MANAGER
Click to expand...
Click to collapse
Hi nick. I made a video of my problem http://www.youtube.com/watch?v=B7cxryEC5ig
Also...if you're telling me to not use Tom manager then what do I use to install roms?
Thanks in advanced
xxkhbxx said:
Hi nick. I made a video of my problem http://www.youtube.com/watch?v=B7cxryEC5ig
Also...if you're telling me to not use Tom manager then what do I use to install roms?
Thanks in advanced
Click to expand...
Click to collapse
Rom manager is not fully functional on the SGSII. In particular, you can not use recovery through Rom Manager. To gain ClockworkMod Recovery, you must install a custom kernel containing CWM Recovery.
You can install a kernel with Odin3, Heimdall, adb, Android Terminal Emulator, or Mobile Odin Lite. If you use Odin3 or Heimdall, this will increment the flash counter. Adb, Terminal and Mobile Odin Lite will not increment the flash counter. If you need specific guidance, look at the FAQ in sticky section of the General forum, or follow the Guide linked in my signature. (I havn't added Mobile Odin Lite to the guide yet, but it's a pretty easy option. If you download it from Chainfires thread, it is free. If you get the pro version from the market there is a small charge.)
You can't boot into recovery through rommanager. You should do the three button boot (press power+volup/down) once you do that you will be able to flash roms without any issue.
Blaze9 said:
You should do the three button boot (press power +vol up/down) once you do that you will be able to flash roms without any issue.
Click to expand...
Click to collapse
You can't flash roms from stock 3e recovery, so unless there is a custom kernel installed on the phone you will not be able to flash roms.
I'll definitely cast a vote for Mobil Odin. I flashed Entropy 512's latest kernal through the Pro version, and it took less than 10 seconds!
creepyncrawly said:
You can't flash roms from stock 3e recovery, so unless there is a custom kernel installed on the phone you will not be able to flash roms.
Click to expand...
Click to collapse
Yes, but he said it is the blue recovery screen, which is CWM. The orange screen is stock recovery.
Blaze9 said:
Yes, but he said it is the blue recovery screen, which is CWM. The orange screen is stock recovery.
Click to expand...
Click to collapse
Yes. I looked at his video again. The video is bad, very blurry, but it does look like he has ClockworkMod Recovery 5.0.2.3 installed, not 3e recovery. So your directions would be good in that case.
BYW, I believe that stock 3e recovery is also blue text. It's been a while since I booted into 3e recovery though.
creepyncrawly said:
Yes. I looked at his video again. The video is bad, very blurry, but it does look like he has ClockworkMod Recovery 5.0.2.3 installed, not 3e recovery. So your directions would be good in that case.
BYW, I believe that stock 3e recovery is also blue text. It's been a while since I booted into 3e recovery though.
Click to expand...
Click to collapse
3e recovery is indeed blue on our phone, just like CWM.
Sent from my SAMSUNG-SGH-I777 using xda premium
Hey Creepy thanks for the heads up and link i feel like part of my prob is syncin to my computer.(it has not been same since windows crashed)Any whos i tried the QR code but said download unsuccessful. Haven't had a chance to do the download. Question is can i just buy mobile Odin off market and download a kernel directly onto my phone from internet/no computer required?
Thanks
ghettopops said:
Hey Creepy thanks for the heads up and link i feel like part of my prob is syncin to my computer.(it has not been same since windows crashed)Any whos i tried the QR code but said download unsuccessful. Haven't had a chance to do the download. Question is can i just buy mobile Odin off market and download a kernel directly onto my phone from internet/no computer required?
Thanks
Click to expand...
Click to collapse
That's is correct. Though mobile odin lite is on xda for free. I used it to flash entropy512's newest kernel. Worked without an issue.
Just make sure you have the zImage already extracted and on your phone.
Sent from my páhhōniē
ghettopops said:
Hey Creepy thanks for the heads up and link i feel like part of my prob is syncin to my computer.(it has not been same since windows crashed)Any whos i tried the QR code but said download unsuccessful. Haven't had a chance to do the download. Question is can i just buy mobile Odin off market and download a kernel directly onto my phone from internet/no computer required?
Thanks
Click to expand...
Click to collapse
Download Mobile Odin Lite from Chainfires OP to your pc, move MobileODINLite-v1.25.apk into the same directory where you have adb.exe, and use adb to install it with:
Code:
adb install MobileODINLite-v1.25.apk
You do not need to try to install the add-on (flashkernel). You don't need it to flash a kernel, but you do need it if you want to flash a rom. When I tried it out this weekend, it would not download the flashkernel, so after I installed the kernel, I deleted Mobile Odin Lite.
creepyncrawly said:
Rom manager is not fully functional on the SGSII. In particular, you can not use recovery through Rom Manager. To gain ClockworkMod Recovery, you must install a custom kernel containing CWM Recovery.
You can install a kernel with Odin3, Heimdall, adb, Android Terminal Emulator, or Mobile Odin Lite. If you use Odin3 or Heimdall, this will increment the flash counter. Adb, Terminal and Mobile Odin Lite will not increment the flash counter. If you need specific guidance, look at the FAQ in sticky section of the General forum, or follow the Guide linked in my signature. (I havn't added Mobile Odin Lite to the guide yet, but it's a pretty easy option. If you download it from Chainfires thread, it is free. If you get the pro version from the market there is a small charge.)
Click to expand...
Click to collapse
Thank you creepy. Thank u everyone. I will try when I get home and get back to you.
BTW what's this counter that you are mentioning?
xxkhbxx said:
Thank you creepy. Thank u everyone. I will try when I get home and get back to you.
BTW what's this counter that you are mentioning?
Click to expand...
Click to collapse
Happy to help. For information on the counter, read the fairly extensive discussions in the flash custom binaries guide and the return to the store guide linked in my signature.
thank you very much, i installed Mob odin lite and the kernel so now i am good to go. I just nandroid backed up my stock rom and am going to give a diff one a try.
creepyncrawly said:
Rom manager is not fully functional on the SGSII. In particular, you can not use recovery through Rom Manager. To gain ClockworkMod Recovery, you must install a custom kernel containing CWM Recovery.
You can install a kernel with Odin3, Heimdall, adb, Android Terminal Emulator, or Mobile Odin Lite. If you use Odin3 or Heimdall, this will increment the flash counter. Adb, Terminal and Mobile Odin Lite will not increment the flash counter. If you need specific guidance, look at the FAQ in sticky section of the General forum, or follow the Guide linked in my signature. (I havn't added Mobile Odin Lite to the guide yet, but it's a pretty easy option. If you download it from Chainfires thread, it is free. If you get the pro version from the market there is a small charge.)
Click to expand...
Click to collapse
Hello again. I haven't tried anything yet time is not permitting me to but I did install a custom kernel when I first rooted. This is the method I used if I haven't posted the link up yet. Its from zedomax on his you tube channel. I did it step by step. I was even able to make backups no problem.
https://www.youtube.com/watch?v=R-2Z2dKsuio&feature=youtube_gdata_player
Creep? I'm on my lunch break reading your other threads and what not... and I saw someone write press power / up and down buttons to get to cwm recovery ... but then I saw someone say release the power button when you see the yellow triangle.
So I did that and was in recovery 5.0.2.3 and attempted to flash cyanogen that I had stored in the phone...... the first attempt took two seconds so I remember on another post people had said to flash it again so I did. It took maybe 10 seconds this time.
I restarted.. and was joyed to see the cyanogen boot screen but was saddened to see it was caught in a boot loop. Would keep restarting and doing the bootup screen. Wouldn't pass that part so I had to do a restore .. any idea what I may be doing wrong..?
I attached a screen shot of my "about phone" thank u thank you everyone
I really can't help with installing CM7. I've never installed it myself.
From what I see, your were on stock with zedomax kernel and CWM 5.0.2.3, which as far as I know meets the requirements to be ready to flash CM7. Maybe someone with more experience can help you.
creepyncrawly said:
I really can't help with installing CM7. I've never installed it myself.
From what I see, your were on stock with zedomax kernel and CWM 5.0.2.3, which as far as I know meets the requirements to be ready to flash CM7. Maybe someone with more experience can help you.
Click to expand...
Click to collapse
Thanks creepy. Just out of curiosity do you have a Tom installed? If so then which? I would like to try your rom and see.
Hi guys I am having a lot of trouble, I am trying to get ICS on my phone, but I don't have CWM, first I did some stuff with odin, and got a soft brick, luckily I returned to stock and am back. I am root, I tried flashing cwm but it won't stick, and I can't flash the zip in the stock recovery. Is there a way I can flash this with Odin?
You have root? No need to use Odin then. Use Mobile Odin; it's much easier, and it won't trip the flash counter.
It wants me to get the pro version, can I have an apk for the free one because I can't find it on the market
It says the device is not supported =[
nsilverman15 said:
It wants me to get the pro version, can I have an apk for the free one because I can't find it on the market
Click to expand...
Click to collapse
It's attached in the first post of this thread
oahceasgnikgneas said:
It's attached in the first post of this thread
Click to expand...
Click to collapse
still giving me android system recovery and not clockworkmod.... =[
nsilverman15 said:
still giving me android system recovery and not clockworkmod.... =[
Click to expand...
Click to collapse
Can you link what exactly you are attempting to flash to get cwm.
On the i777 recovery is part of the kernel so to get cwm recovery you should be flashing a kernel with cwm.
Sent from my SGH-I777 using XDA Premium HD app
dayv said:
Can you link what exactly you are attempting to flash to get cwm.
On the i777 recovery is part of the kernel so to get cwm recovery you should be flashing a kernel with cwm.
Sent from my SGH-I777 using XDA Premium HD app
Click to expand...
Click to collapse
Ooh, can you please give me a link to an odin kernel with cwm?
I can't use a cwm flashable one because I don't have ics, so I am going to need a tar.
Read this: http://forum.xda-developers.com/showthread.php?t=1511838
http://forum.xda-developers.com/showthread.php?t=1289460
You can use any of these - you just have to use some kind of archive manager and extract the "zimage" file (the zimage is the kernel) from the zip you download from this thread. Put that zimage on your phones sdcard (note there is no file extension on the zimage file) and you can flash that with mobile Odin.
Also I have not read through the op in a while but I think entropy included at least one straight Odin flashable kernel download link, but like I said above you can extract the zimage from any one of his links and that can be flashed in mobile Odin.
Sent from my SGH-I777 using XDA Premium HD app
Flashed, now it is just blank, I guess i'll wait a bit
nsilverman15 said:
Flashed, now it is just blank, I guess i'll wait a bit
Click to expand...
Click to collapse
What did you flash? And what do you mean by "it is just blank"?
Sent from my SGH-I777 using XDA Premium HD app
Dayv, Can you flash any of Entropy512's DD on 2.3.4 KH7 stock with root to get CWM with no probs? I know to flash the Zimg in mobile odin. Is that the only way to get CWM on the phone by flashing another kernel? Just wondering how to back up my stock kernel with out flashing another kernel with CWM. So I guess Entropy512's kernel is a stock modified kernel? Just trying to get this all figured out. Thanks for any info you can provide!
Edit: N/M I need to back up my stock ROM with CWM not the "Kernel" I get it now.... Will Entropy512's DD work with 2.3.4 KH7 stock with root with no probs?
snipe2nite said:
Dayv, Can you flash any of Entropy512's DD on 2.3.4 KH7 stock with root to get CWM with no probs? I know to flash the Zimg in mobile odin. Is that the only way to get CWM on the phone by flashing another kernel? Just wondering how to back up my stock kernel with out flashing another kernel with CWM. So I guess Entropy512's kernel is a stock modified kernel? Just trying to get this all figured out. Thanks for any info you can provide!
Edit: N/M I need to back up my stock ROM with CWM not the "Kernel" I get it now.... Will Entropy512's DD work with 2.3.4 KH7 stock with root with no probs?
Click to expand...
Click to collapse
Yes, Entropy's DD will work with KH7.
So what you're trying to do is...what? Back up your stock ROM? If you're just talking about the stock system image and kernel, you don't need to back those up; you can always download them again from the Return to Stock thread.
If you're trying to do a nandroid backup (full system + data backup), you can't do that without flashing a kernel containing CWM Recovery. Entropy's kernel is one of these. Just flash that kernel using Mobile Odin.
It seems you've confused a couple things, I'll clarify.
On these phones, CWM is included with the custom Kernels provided by Entropy512, or Ktoon or Siyah, et al. CWM however, is not a Kernel, when you boot into CWM mode, your bypassing the loading of the Kernel. Think of it like this. When you press the power button (and only the power button) on your phone, it's hard wired into the phone to boot the Kernel, the Kernel sets up a hardware environment, loads the RAMDisk etc and does it's thing. IF you have a Kernel that includes CWM, you can bypass this by loading CWM INSTEAD of the Kernel. Note, you need to reboot into CWM or use a different set of buttons to get there, power alone, is hard wired to boot the Kernel.
If you came from a different manufacturer, say Motorola, the above process is different, as they lock their bootloaders and you cannot change the Kernel, you use a different process to load CWM, and boot to it instead of the Kernel. As Samsung has an unlocked bootloader, the process of getting CWM is much simpler.
And Mattdm is 100% correct, no need to flash your stock recovery, it's easy enough to download it. If you've got your phone all setup just the way you want it and want to make a backup of it, boot into CWM, scroll to backup and restore, press power, choose backup, use volume up/down to scroll to backup and press power. It will create a backup in a folder called Clockworkmod. It can easily be restored via CWM if you have the need too.
Hope this helped a lil.
Wink
Thanks Mattdm and Winklie I see now it's a full system + data backup not a Kernel back up... Any tips on what one of Entropy512's DD to flash? I see people in that thread saying 12/8/2011? I just don't want the battery problem people talk about. I prob should be asking these questions in that thread huh? Thanks again!! XDA and all (well most) the people on here are the BEST....
snipe2nite said:
Thanks Mattdm and Winklie I see now it's a full system + data backup not a Kernel back up... Any tips on what one of Entropy512's DD to flash? I see people in that thread saying 12/8/2011? I just don't want the battery problem people talk about. I prob should be asking these questions in that thread huh? Thanks again!! XDA and all (well most) the people on here are the BEST....
Click to expand...
Click to collapse
Yeah 12/8 is a good one. I've always been partial to 2/28 though, and I've also had good results with 3/4. Try a couple and see which one works better for you.
Kernels behave differently on different phones. I am using the NEAK Kernel with amazing performance and battery life. Others have had problems, with the exact same hardware, so it shows a lack of maturity in the fab process for these kinds of variances.
As for changing Kernels, use a Kernel cleaning script found here http://forum.xda-developers.com/showthread.php?t=1428530 before each change.
Barring a problem (lockup, reboots, etc) you need a give a Kernel 3 or so battery charges to 'settle in' before you can really access the battery life. Like I said, different Kernels behave differently on different peoples phones, so what works for me, might not work for you. However it's so simple to change Kernels, feel free to experiment to find what suits your needs best.
Hope this helped.
Wink
Winklie said:
As for changing Kernels, use a Kernel cleaning script found here http://forum.xda-developers.com/showthread.php?t=1428530 after each change.
Click to expand...
Click to collapse
Shouldn't you use the script before each change?
Hey guys.
I've searched the forums for this issue, unfortunately it seems like mine is a little unique and I can't find a solution to my problem anywhere.
I'm stuck in CWM Recovery mode, and although I can navigate the menu... when pressing the Home key to select the various options, nothing happens besides the options blinking for a sec. I can access Odin Mode with Power/Volume +/- but that's it. Also it's worth noting that I'm unable to access my phone's files from my computer when in download mode (my guess is because the phone isn't set to USB storage mode which I have to do from the booted home screen, which... I can't access).
This happened after the first time entering Recovery mode on CWM, and although I have ROM Manager installed on my phone, after researching a little I found that was NOT what I wanted to use. And I did NOT use that program.. my CWM was flashed in from a .tar on Odin (the windows program). I also have a Jellybam folder placed in the phone, which was my next step.
How can I get out of CWM Recovery so that I can continue flashing the Jellybam ROM?
I apologize if I've missed anything. Please let me know if you need any other information. I'll be sure to hit the thank you button on every reply.
THANK YOU!
:crying:
um....
you are supposed to flash the ROM from CWM, so why would you want to get out of CWM to get back into CWM?
you havent mentioned what version of Android you were already running or what kernel you flashed, but have you tried using the POWER button to select things in CWM? Are you sure you used the right kernel? Are you sure you have an i777?
Hey Pirateghost, thanks for the reply! And yes, I was going into CWM Recovery to flash the ROM. The reason I wanted out of CWM was because it had no functionality... yes, I did try using the power button to select things. Seems the home button was it? In any case nothing worked. My version of Android was Gingerbread UCKH7, and I'm %100 sure it's an i777. By using the "right kernel" you mean the right version of Jellybam?
UPDATE: I got out of the bootloop by using a stock root UCKH7 kernel, bringing it in from Odin. Now I'm just trying to understand what went wrong and how I can continue to flash my Jellybam ROM in without any issues. I also found that my CWM app disappeared after I uninstalled ROM Manager after getting access back to my phone.
More info...
the kernel I installed for CWM was KH4 at this thread: http://forum.xda-developers.com/showthread.php?t=1103399
After putting the KH7 stock root kernel in via Odin and getting out of the bootloop, I deleted ROM Manager off my phone and reflashed the KH4 kernel so I could get CWM. That worked fine, but now Superuser is crashing.
??
xargis said:
More info...
the kernel I installed for CWM was KH4 at this thread: http://forum.xda-developers.com/showthread.php?t=1103399
After putting the KH7 stock root kernel in via Odin and getting out of the bootloop, I deleted ROM Manager off my phone and reflashed the KH4 kernel so I could get CWM. That worked fine, but now Superuser is crashing.
??
Click to expand...
Click to collapse
The kernel you just linked above is for the GT-I9100, not the SGH-I777. You seem to be moving forward without providing yourself with enough knowledge. If you are sure the phone is an I777 then stay away from the I9100 forums. Get what you need from here. There is lots of information in the guides linked in my signature. There is enough information there to guide you through everything you want to do.
xargis said:
More info...
the kernel I installed for CWM was KH4 at this thread: http://forum.xda-developers.com/showthread.php?t=1103399
After putting the KH7 stock root kernel in via Odin and getting out of the bootloop, I deleted ROM Manager off my phone and reflashed the KH4 kernel so I could get CWM. That worked fine, but now Superuser is crashing.
??
Click to expand...
Click to collapse
You are flashing an older kernel on a newer ROM??? why? if you want to have CMW recovery you should flash your stock rom and then get the CWM .tar file and flash it in Odin. If you happen to get a .zip CWM file you can rename it to update.zip and flash it using your stock ROM's recovery options.
Search something along these lines: CWM5.8.1.8-i777.zip or recovery-clockwork-5.0.2.3-galaxys2att.tar as examples
creepyncrawly said:
The kernel you just linked above is for the GT-I9100, not the SGH-I777. You seem to be moving forward without providing yourself with enough knowledge. If you are sure the phone is an I777 then stay away from the I9100 forums. Get what you need from here. There is lots of information in the guides linked in my signature. There is enough information there to guide you through everything you want to do.
Click to expand...
Click to collapse
WOW! I don't know how I missed that. Must pay more attention to detail...
Thank you so much for pointing that out Creepyncrawly!
Commodore 64 said:
... If you happen to get a .zip CWM file you can rename it to update.zip and flash it using your stock ROM's recovery options. ...
Click to expand...
Click to collapse
It's great having new folks around helping out.
This is bad information, however. 3e recovery will enforce signature verification on any update.zip, and it will fail.
creepyncrawly said:
It's great having new folks around helping out.
This is bad information, however. 3e recovery will enforce signature verification on any update.zip, and it will fail.
Click to expand...
Click to collapse
always a pleasure to lend a hand. you're right it used to work on 2e I think, I was trying to signify the difference between the zip and tar, but thank you so much for the correction.
So should I be using a different kernel? I'm sorry I'm not quite sure what you're saying Commodore64, my head has been spinning from all this.
xargis said:
So should I be using a different kernel? I'm sorry I'm not quite sure what you're saying Commodore64, my head has been spinning from all this.
Click to expand...
Click to collapse
you should be using a kernel intended for your phone....your phone (if branded AT&T) is either an i727 skyrocket or i777. this is the i777 forum section. you appear to have flashed a kernel for an i9100...
just follow creepy's guides and do it the right way. there is nothing you can flash in STOCK recovery that will give you CWM or a new kernel (which on this phone CWM is packed with the kernel)
xargis said:
So should I be using a different kernel? I'm sorry I'm not quite sure what you're saying Commodore64, my head has been spinning from all this.
Click to expand...
Click to collapse
There is not just one answer, you can go back to one of the stock ROMs, like the ones provided by creepyncrawly threads.
There are a lot of threads on this and I don't have my I777 anymore but I used to do this:
1- Once you flashed a stock rom, go into recovery and cleanup. data/cache reset.
2- Have the files you want to flash on your phone. (if you format the SD card you will erase your files including the ones you want to flash!)
3- Use your .tar Odin CWM that worked for you before now to flash CWM.
4- Once in the CWM flash a newer CWM version (CWM6.0.1.0-i777.zip) since your ROM is based on CM/AOKP
5- After flash Go to Advanced and reboot recovery (this will reboot your phone now with the newer version of CWM)
6- Once in the newer CWM clean up again.
7- Don't reboot, have the correct version (latest or whatever) of your Custom ROM and install it now.
This is the general idea, if you don't know what you're doing read the threads in the development section, everything you need is there.
Educate yourself before you make your phone a crippled rabbit and scream for help.
Commodore 64 said:
There is not just one answer, you can go back to one of the stock ROMs, like the ones provided by creepyncrawly threads.
There are a lot of threads on this and I don't have my I777 anymore but I used to do this:
1- Once you flashed a stock rom, go into recovery and cleanup. data/cache reset.
2- Have the files you want to flash on your phone. (if you format the SD card you will erase your files including the ones you want to flash!)
3- Use your .tar Odin CWM that worked for you before now to flash CWM.
4- Once in the CWM flash a newer CWM version (CWM6.0.1.0-i777.zip) since your ROM is based on CM/AOKP
5- After flash Go to Advanced and reboot recovery (this will reboot your phone now with the newer version of CWM)
6- Once in the newer CWM clean up again.
7- Don't reboot, have the correct version (latest or whatever) of your Custom ROM and install it now.
This is the general idea, if you don't know what you're doing read the threads in the development section, everything you need is there.
Educate yourself before you make your phone a crippled rabbit and scream for help.
Click to expand...
Click to collapse
this makes no sense, dude.
1. if he is on a stock rom, there is nothing CM/AOKP on his phone
2. on this device the recovery is packed with the kernel, flashing some other CWM doesnt really matter at all. none of this is necessary.
you can flash any kernel you want (made for this device) if you dont plan on booting the OS and only plan on flashing a rom...
you have now complicated an already easy method.
Hey everyone - just wanted to let you guys know that I am now running JellyBAM and so far everything seems fine.
Thank you all for your help, seriously. If anyone has any questions about what I did etc., just ask and I'll get back to ya.
Thanks! :good:
Glad to hear you got JellyBAM up and running xargis, and just to reiterate what pirateghost was saying, you won't get CWM by flashing a CWM.tar file lol, I don't even think one can be found for this model (SGH-i777) which is the device that I currently have, the ONLY way to get CWM onto this device is to flash the proper kernel for this device, but keep in mind that there is another factor to think about as well, depending on what type of custom rom you want to run there are different kernels out there that work best and offer different/better features for deployment into the custom rom for which you will be running, in other words some roms are kernel specific, you can only use certain kernels with CM10/AOKP/ParanoidAndroid based roms, and such is the same with only using certain kernels with Sammy based stock roms, so the choice is yours, hope this info was informative to you and that you definately find a good productive rom that you will be happy to play with and run, have fun with your i777 s2, that's one of the things this forum is all about!!
So you've just gotten/inherited an I-777 and you need to get rid of the 2 year old UI and OS ASAP, but all the other guide threads are just as old and filled with old info, what to do?
DISCLAIMER: I am not responsible for phone bricks and the like. You follow this information at your own risk. This is just information I'm writing down as I update my wife's old bone stock phone
BACKUP your data from both cards, you are likely to lose the internal SD data in this operation
Let's get started:
Root the phone:
Go here: Framaroot.
Download the .apk, and put it on your phone.
Be sure to 1. Have install from unknown sources on. 2. Enable USB debugging.
Install the .apk and run it.
Choose SuperSU and then click on Aragorn (should automatically be detected).
Reboot the phone (power cycle is probably the only option in stock).
Congrats! You're now rooted!
Install a kernel
Go here: Mobile Odin.
Grab two apks; Mobile Odin Lite and the Flash kernel for i-777. (Flash kernel is many posts down from the top)
Extract the .apk from the Flash kernel .zip file, and plop both .apks on your phone.
Install the .apks
Go here: ShoStock and click on the 'older kernels + a tar version'
Download the .tar
Plop the .tar on your phone
EDIT: At this point you may want to also grab a rom and any other files you may need if you only have the internal sd available because you'll lose USB mount access past this point. So go ahead and transfer those files to the phone.
Open Mobile Odin Lite and select the .tar file
Flash it, the device will instantly reboot after flash.
The device won't fully boot now, but don't worry! Hold down POWER, VOL UP and VOL DOWN until the phone cycles and the logo appears, then let go of the buttons and you should be in CWM recovery which came with the jeboo kernel you flashed.
Install a ROM
You will have to wipe/factory reset first from the CWM menus.
Flash your rom, regardless, follow the instructions in the OP of the ROM thread you're interested in.
I flashed ShoStock first since it's likely more like an OTA update to bring partitions up to date before flashing anything else.
Be sure to hit THANKS on the posts you visit from this guide.
Nice to see an updated guide.
For your fifth step of Kernel install, you lead users to a jeboo kernel, which is great if they plan to go ShoStock. I believe that the Jeboo kernel is a mic swap kernel, and may not be suitable for other very popular and common ROMS for the I777 (any AOSP or stock samsung, or COOKED).
Therefore I suggest adding such a note, and providing a link to at least one of the Siyah(based) Kernels.
These are available in several versions, and in .tar or .img format; both of which can be flashed via mobile ODIN (extract the .zip, flash the boot.img)
if flashing to an ICS Rom:SiyahKernel S2-v5.0.1
If flashing to a JB Rom: AJK BOSS (newest available)
Edit: props to @othermark for compiling this simple updated means to root & rom on the i777
cyril279 said:
Nice to see an updated guide.
For your fifth step of Kernel install, you lead users to a jeboo kernel, which is great if they plan to go ShoStock. I believe that the Jeboo kernel is a mic swap kernel, and may not be suitable for other very popular and common ROMS for the I777 (any AOSP or stock samsung, or COOKED).
Click to expand...
Click to collapse
Most, if not all, roms here will come with the appropriate kernel which will be flashed during the ROM install. They would have to reflash the jeboo kernel to get something incompatible. This is just to get them something that 1. has CWM and 2. is a .tar they can flash with Mobile Odin Lite.
That said, sometimes you have to flash a compatible kernel before you flash a particular ROM.
othermark said:
...This is just to get them something that 1. has CWM and 2. is a .tar they can flash with Mobile Odin Lite...
Click to expand...
Click to collapse
Mobile Odin Lite (and Pro) will recognize and flash a zImage. So one can pull the zImage from any CWM flashable zip and use it.
cyril279 said:
Nice to see an updated guide.
For your fifth step of Kernel install, you lead users to a jeboo kernel, which is great if they plan to go ShoStock. I believe that the Jeboo kernel is a mic swap kernel, and may not be suitable for other very popular and common ROMS for the I777 (any AOSP or stock samsung, or COOKED).
Therefore I suggest adding such a note, and providing a link to at least one of the Siyah(based) Kernels.
These are available in several versions, and in .tar or .img format; both of which can be flashed via mobile ODIN (extract the .zip, flash the boot.img)
if flashing to an ICS Rom:SiyahKernel S2-v5.0.1
If flashing to a JB Rom: AJK BOSS (newest available)
Edit: props to @othermark for compiling this simple updated means to root & rom on the i777
Click to expand...
Click to collapse
So if i wanted to Do Cyanogen Mod(10.2), would it be okay to use the jeboo tar? Or should i download AJK, unzip it, and install the boot.img instead of the jeboo .tar?
TreatnHerRight said:
So if i wanted to Do Cyanogen Mod(10.2), would it be okay to use the jeboo tar? Or should i download AJK, unzip it, and install the boot.img instead of the jeboo .tar?
Click to expand...
Click to collapse
It should not matter which version of CWM recovery you use, so Jebo will be fine. When you install it, your system may not boot up, but just turn the phone off, then use the button combination for recovery mode.
Edit: boot.img is a partition file that Mobile Odin will recognize, the same as zImage, so you can use it to install AJK if you prefer. Again, it shouldn't matter which one you use.
TreatnHerRight said:
So if i wanted to Do Cyanogen Mod(10.2), would it be okay to use the jeboo tar? Or should i download AJK, unzip it, and install the boot.img instead of the jeboo .tar?
Click to expand...
Click to collapse
I can't vouch for the jeboo approach, but I expect that it works.
I did use this guide with the latest ajk-extracted boot.IMG as you describe, and it works as well.
Fyi: If you're using mobile Odin pro, you don't need the i777- kernel download, the pro version does it for you.
9. Open Mobile Odin Lite and select the .tar file
What do i click at this point(To Flash the .tar)? I opened Mobile ODIN Lite, now do i click Kernel, System, Data, Cache...., or Open file...?
Just wanna make sure.
Also:
cyril279 said:
I can't vouch for the jeboo approach, but I expect that it works.
I did use this guide with the latest ajk-extracted boot.IMG as you describe, and it works as well.
Fyi: If you're using mobile Odin pro, you don't need the i777- kernel download, the pro version does it for you.
Click to expand...
Click to collapse
To Do The Boot.IMG Which Would i click?
Select [kernel], navigate to and select the boot.img.
Then scroll down to the bottom of mobile Odin and select [flash firmware]
cyril279 said:
Select [kernel], navigate to and select the boot.img.
Then scroll down to the bottom of mobile Odin and select [flash firmware]
Click to expand...
Click to collapse
Used This Guide, Followed Everything Until the .tar File, i Instead flashed the AJK boot.IMG file. It Successfully Brought up CMW Recovery. When Attempting to Flash Cyanogen Mod or Paranoid Android I Got Error Status 7 (getprop("ro.product.device") == "SGH-I777 || getprop("ro.build.product") == "SGH-I777") Same Error for Both.
Steps i took to Fix.
Opened Unzipped Cyanogen Mod.
Open Build.prop and Rename SGH-I777 to i777 In those Two Spots (ro.build.product and ro.product.device)
Opened Updater-Script and Removed the First 2(or 3) Lines Referencing the SGH-i777
Then Re zipped them using this method - [UltimateGUIDE][How-to]Create your Own Custom ROM an easy way
Flashed in Recovery and it Successfully Worked. (Tested it With the Cyanogen Mod Zip Only, Got Error Previously With Both CM and PA Zips)
Me Attempting To Help Anyone Else In This Situation.
nice, do you guys know if it's possible to use this phone without a data plan on att? i recently upgraded my phone and wanted to give this one to my dad, he can use it to watch youtube videos and videochat with my grandmother via wifi at home, there was a thread i read on how to unlock the phone and it had an option for network lock, is that what i need to do? any help is very much appreciated
baoweezie said:
nice, do you guys know if it's possible to use this phone without a data plan on att? i recently upgraded my phone and wanted to give this one to my dad, he can use it to watch youtube videos and videochat with my grandmother via wifi at home, there was a thread i read on how to unlock the phone and it had an option for network lock, is that what i need to do? any help is very much appreciated
Click to expand...
Click to collapse
I don't really understand... You simply take the Sim card out and put the thing in airplane mode.
I did that with mine and the battery lasts a week. BTW you can turn on WiFi while in airplane mode. You can also uncheck "use data" in the mobile network settings.
There's nothing complicated to do.
Sent from my Nexus 4 using xda app-developers app
Yes I know about airplane mode but im trying to have him use this phone as a actual phone that can make calls but didn't want att to tack on an additional data plan to it because he never uses any data while out and about. Basically I want to use this phone on my dads line without having to add a monthly data plan.
He was using a T-Mobile phone that I unlocked for him before and they didn't add the data plan on cause att doesn't recognise T-Mobile imei, I could be wrong but if I can change something in the phones build prop to make it seem like a non att branded phone, would it not be detected as a smartphone and not trigger the data add on?
Sent from my SGH-I337 using xda app-developers app
baoweezie said:
nice, do you guys know if it's possible to use this phone without a data plan on att? i recently upgraded my phone and wanted to give this one to my dad, he can use it to watch youtube videos and videochat with my grandmother via wifi at home, there was a thread i read on how to unlock the phone and it had an option for network lock, is that what i need to do? any help is very much appreciated
Click to expand...
Click to collapse
This question, and it's resulting discussion are better suited in a separate thread. That helps to both get you views and answers that are more focused on your issue, as well as keeping this [GUIDE] thread clean and on-topic.
-Cyril
Nevermind, I figured it out.
The key combo to get into my recovery is Vol Up + Vol Down + Power
Is not clear for me in conclusion how obtain CWM in the i777 rooted??
pepe100 said:
Is not clear for me in conclusion how obtain CWM in the i777 rooted??
Click to expand...
Click to collapse
This has been answered for you already, several times. CWM is included in our kernels - you DO NOT flash it separately. Just pick a kernel that matches the android version you're on (ICS, JB etc.), flash it and it'll install CWM for you!
Sent from the i777
OK bro thanks for your concrete answer.
Sent from my SGH-I777 using xda app-developers app
i cant find the 'older kernels + a tar version' in shos thread .. pls help me !
nathan_42594 said:
i cant find the 'older kernels + a tar version' in shos thread .. pls help me !
Click to expand...
Click to collapse
It's in post #3.
jeboo said:
** OLD VERSION DOWNLOADS INCLUDING A TAR VERSION **
Code:
http://d-h.st/users/jeboo/?fld_id=9729
In a bind and need a tar version, just extract zImage from the zip and do: tar -H ustar -c zImage >> jeboo_kernel.tar
Click to expand...
Click to collapse
LATEST EDIT http://forum.xda-developers.com/showpost.php?p=55161735&postcount=17
EDIT 2: http://forum.xda-developers.com/showthread.php?p=55095194#post55095194
EDIT: I got it rooted now but i would like some help flashing a custom ROM onto it. like what i need to know about it and stuff and which ROMs work for galaxy player 5.0. I was looking at cyanogenmod 11 but and the beanstalk one, but the rear camera doesn't work right i heard. I would kindof like a kitkat rom but if i have to use jellybean then i guess i do. i would like to know which rom is recommended
hey you all i need a little help rooting my galaxy player 5.0. model YP-G70 firmware 2.3.5 kernel version [email protected] #2 build number GINGERBREAD.UEK18
i was gonna use the superoneclick program but it says "file download blocked." isn't shortfuse.org the site to get it from? or where do i get the program?
I had already installed Samsung Kies, but now i need the superoneclick program. I was trying to get version 2.3.3. so what i'm wondering is where and how do you get superoneclick???
I've done a lot of researching which way is the best to root it, and i think superoneclick looks best. please tell me different if i'm wrong ... so yeah... thanks in advance
Your right to try and use superoneclick as a rooting program. Try downloading the most updated version and scan on Norton for viruses. Then open the program, make sure you have USB debugging on and hit root. After that hit yes when you get prompted to test and unplug your device and reboot.
http://m.download.cnet.com/SuperOneClick/3000-2094_4-75447027.html
Here's a link to CNET to download. If diwnlias did not work try looking for it on xda
Sent from my YP-G70 using XDA Free mobile app
troy5890 said:
Your right to try and use superoneclick as a rooting program. Try downloading the most updated version and scan on Norton for viruses. Then open the program, make sure you have USB debugging on and hit root. After that hit yes when you get prompted to test and unplug your device and reboot.
Here's a link to CNET to download. If diwnlias did not work try looking for it on xda
Sent from my YP-G70 using XDA Free mobile app
Click to expand...
Click to collapse
thanks for answering!! i clicked on the link and hit download and it downloaded but it said that chrome blocked, cause it's malicious. (pic below) it shows up under my downloads though. i scanned it with vipre (i use that instead of norton) and it said it was trojan. should i just try to run it anyway or what...
edit: i tried opening it from my downloads and here's what it brings up. pic below
Antivirus saying the package is malicious is perfectly normal. The 2 root exploits used in SuperOneClick are already identified as Android-based trojans in all modern antivirus softwares. If you downloaded from a trusted site, DISABLE your antivirus software and start the rooting process. When you're done, don't forget to turn it back on.
Sent from Google Nexus 4 @ CM11
wow you're right!! I got it rooted!! so i think... i have the app superuser soo yeah... now i wanna flash a custom rom which i have to research or if you all would be kind enough to help me with. i didn't do any research on that yet so i really know nothing. just that i'm missing out on some good stuff i think
Austin68 said:
wow you're right!! I got it rooted!! so i think... i have the app superuser soo yeah... now i wanna flash a custom rom which i have to research or if you all would be kind enough to help me with. i didn't do any research on that yet so i really know nothing. just that i'm missing out on some good stuff i think [/QUOTE
Now that you are rooted it is time for some awesome custom ROMs. There is cm11 you could try by going into the development page and downloading it. But before you flash make sure you have a nandroid back up and you go in this order if you want to run cm11.
Gingerbread, ice cream sandwich, jelly bean, jelly bean 4.3, then cm11. Make sure your recovery is updated when flashing different rims or it might come out as a herring.
Also you could just go straight to KitKat. If you want.
Sent from my YP-G70 using XDA Free mobile app
Click to expand...
Click to collapse
troy5890 said:
Austin68 said:
wow you're right!! I got it rooted!! so i think... i have the app superuser soo yeah... now i wanna flash a custom rom which i have to research or if you all would be kind enough to help me with. i didn't do any research on that yet so i really know nothing. just that i'm missing out on some good stuff i think [/QUOTE
Now that you are rooted it is time for some awesome custom ROMs. There is cm11 you could try by going into the development page and downloading it. But before you flash make sure you have a nandroid back up and you go in this order if you want to run cm11.
Gingerbread, ice cream sandwich, jelly bean, jelly bean 4.3, then cm11. Make sure your recovery is updated when flashing different rims or it might come out as a herring.
Also you could just go straight to KitKat. If you want.
Sent from my YP-G70 using XDA Free mobile app
Click to expand...
Click to collapse
I think he doesn't even have a custom recovery yet and need some guide on that. Unfortunately I couldn't help because I have a Player 4.0 instead of 5.0.
Sent from Google Nexus 4 @ CM11
Click to expand...
Click to collapse
no i don't have a custom recovery or a nandroid backup. not sure how to make them either, but i'll do some checkin' around. also idk which rom to choose. I'm kinda hoping to get 4.4 kitkat if i can, but i'm only on 2.3.5 now soo... i hope i can. i was thinkin' about cygenmod but i've heard that the camera doesn't always work then. and i'm not exactly sure how to get it. If you wanna help me out I'd really appreciate it
The camera works
Sent from my YP-G70 using XDA Free mobile app
I was reading some tutorials for installing CWM recovery. a lot of them say that you would have to flash a kernel with it built into it. and another one says to use rom manager app which I have but the app doesn't support a galaxy player 5.0. so i wanna install it but I don't know how. like there are so many tutorials. flashing a kernel is risky I heard. not sure how i should start
Austin68 said:
I was reading some tutorials for installing CWM recovery. a lot of them say that you would have to flash a kernel with it built into it. and another one says to use rom manager app which I have but the app doesn't support a galaxy player 5.0. so i wanna install it but I don't know how. like there are so many tutorials. flashing a kernel is risky I heard. not sure how i should start
Click to expand...
Click to collapse
Go for the kernel route. Find a CWM'd kernel that supports your current version of stock ROM and flash that. ROM Manager performs badly even on supported devices so don't even think about it.
And... The risk of flashing a kernel/ROM is something you eventually have to get over if you want your device better
Sent from Google Nexus 4 @ CM11
AndyYan said:
Go for the kernel route. Find a CWM'd kernel that supports your current version of stock ROM and flash that. ROM Manager performs badly even on supported devices so don't even think about it.
And... The risk of flashing a kernel/ROM is something you eventually have to get over if you want your device better
Sent from Google Nexus 4 @ CM11
Click to expand...
Click to collapse
ok thanks!! I'll start lookin' for the right kernel if you have any recommendations just let me know =D
ok I downloaded a kernel (didn't flash it yet). I downloaded this kernel > http://forum.xda-developers.com/showthread.php?t=2318550 and i'm gonna download odin to flash it with but i don't think it's a .tar file so will odin work???? also i guess i'll just download the latest version of odin...?? it said that some versions aren't compatible with some devices.
EDIT it's a .zip file. i think you need cwm to flash it. please tell me if i'm wrong. but i don't have cwm. so i think i might have to choose another kernel ??
also will flashing that kernel erase my third-party apps or app data??
and when i get this kernel on, will I be able to run cm11 on here or will i have to get a different kernel to run on that??
also i think this vid might be a good one. but he never says that he does a nandroid backup or anything
https://www.youtube.com/watch?v=mlyTZZVOvag
Austin68 said:
ok I downloaded a kernel (didn't flash it yet). I downloaded this kernel > http://forum.xda-developers.com/showthread.php?t=2318550 and i'm gonna download odin to flash it with but i don't think it's a .tar file so will odin work???? also i guess i'll just download the latest version of odin...?? it said that some versions aren't compatible with some devices.
EDIT it's a .zip file. i think you need cwm to flash it. please tell me if i'm wrong. but i don't have cwm. so i think i might have to choose another kernel ??
also will flashing that kernel erase my third-party apps or app data??
and when i get this kernel on, will I be able to run cm11 on here or will i have to get a different kernel to run on that??
also i think this vid might be a good one. but he never says that he does a nandroid backup or anything
https://www.youtube.com/watch?v=mlyTZZVOvag
Click to expand...
Click to collapse
Yeah this kernel is CWM only, so no go. As far as Odin compatibility goes, no, the latest version won't always work with anything. Use Odin 1.8x if you can (mine is 1.85 for my Player 4.0 and Captivate, should be the same for Galaxy S-family devices).
Kernels don't wipe any of your data, though flashing a wrong kernel which causes bootloop may do.
After flashing the corresponding kernel, get into CWM recovery and start flashing CM or the ROM you want as per the instructions given in the ROM's post. All AOSP-based ROMs run different (and incompatible) kernels than stock so don't worry about kernels once you're in.
Sent from Google Nexus 4 @ CM11
AndyYan said:
Yeah this kernel is CWM only, so no go. As far as Odin compatibility goes, no, the latest version won't always work with anything. Use Odin 1.8x if you can (mine is 1.85 for my Player 4.0 and Captivate, should be the same for Galaxy S-family devices).
Kernels don't wipe any of your data, though flashing a wrong kernel which causes bootloop may do.
After flashing the corresponding kernel, get into CWM recovery and start flashing CM or the ROM you want as per the instructions given in the ROM's post. All AOSP-based ROMs run different (and incompatible) kernels than stock so don't worry about kernels once you're in.
Sent from Google Nexus 4 @ CM11
Click to expand...
Click to collapse
so what kernel should i get? it has to be a Gingerbread one right? since i'm still on stock gingerbread rom. should I use Entropy's Daily Driver? that would be the only other one, right?
and once i get a jellybean or a kk rom wouldn't it be a good idea to get a better kernel?? like one made for a kk or jb? would it be faster? but then i would have to switch kernels if i would for any reason want to go back to stock gb rom??
Austin68 said:
so what kernel should i get? it has to be a Gingerbread one right? since i'm still on stock gingerbread rom. should I use Entropy's Daily Driver? that would be the only other one, right?
and once i get a jellybean or a kk rom wouldn't it be a good idea to get a better kernel?? like one made for a kk or jb? would it be faster? but then i would have to switch kernels if i would for any reason want to go back to stock gb rom??
Click to expand...
Click to collapse
I have a Player 4.0 instead of a 5.0 so unfortunately can't help you with finding the right kernel. Yes it's best for stock Gingerbread, but if you find Froyo ones, they can also be used. Do note that you can't boot into Gingerbread with a Froyo kernel, so use its CWM to flash whatever you want immediately afterwards.
I don't know of any JB/KK custom kernels, and since Player's single core CPU has its limitations, a custom kernel won't make it much better. At least on my IncS, even overclocking to 1.6GHz won't help with KK eating up my resources.
GB, JB, KK - kernels for different versions of Android are usually not cross-compatible, so you *must* switch kernel if you want to fall back to GB.
Sent from Google Nexus 4 @ CM11
AndyYan said:
I have a Player 4.0 instead of a 5.0 so unfortunately can't help you with finding the right kernel. Yes it's best for stock Gingerbread, but if you find Froyo ones, they can also be used. Do note that you can't boot into Gingerbread with a Froyo kernel, so use its CWM to flash whatever you want immediately afterwards.
I don't know of any JB/KK custom kernels, and since Player's single core CPU has its limitations, a custom kernel won't make it much better. At least on my IncS, even overclocking to 1.6GHz won't help with KK eating up my resources.
GB, JB, KK - kernels for different versions of Android are usually not cross-compatible, so you *must* switch kernel if you want to fall back to GB.
Sent from Google Nexus 4 @ CM11
Click to expand...
Click to collapse
thank you very much for your help. i was able to flash a custom kernel and get cwm. thanks you helped a lot
now i got the rom i was gonna flash downloaded it and extracted it. and i shouldn't have extracted it. then i was trying to flash it and i discovered i messed up. so i pulled the sd card out (which i had a complete nandroid backup on.) [the real mistake] and decided to start over. like, put the zipped files on the sd card. so i put the zips (unextracted) onto my micro sd but it can't mount the sd. so i think i'm like screwed. please help me
oh and when i boot all i see is the samsung logo, then it goes straight to cwm recorvery. I can also get into download mode. so I can get into cwm but my recovery is on my micro sd and it can't mount it. (i did a nandroid backup but it doesn't benefit me now. i also have to backup on my pc, but my pc doesn't wanna recognize it) did i brick it??
what i did...went into cwm wipe data/factory reset and wiped it. next > mounts and storage and clicked format system, and formatted it. then last i wiped dalvik cache. then i went to flash the rom (CM9) and it didn't flash. (because i had extracted it on the pc. it no longer was a .zip) don't know what i was thinkin' but yeah...
as of now i'm gonna start looking for threads to fix it.
i don't think samsung kies is working right either. :/ http://i.imgur.com/WV0iBPk.jpg
please help me unbrick it or whatever i need to do. only made one small mistake and now all this... :'( if you know anything about how to fix it pls reply. i need all the help i can get. thanks ...
Austin68 said:
thank you very much for your help. i was able to flash a custom kernel and get cwm. thanks you helped a lot
now i got the rom i was gonna flash downloaded it and extracted it. and i shouldn't have extracted it. then i was trying to flash it and i discovered i messed up. so i pulled the sd card out (which i had a complete nandroid backup on.) [the real mistake] and decided to start over. like, put the zipped files on the sd card. so i put the zips (unextracted) onto my micro sd but it can't mount the sd. so i think i'm like screwed. please help me
oh and when i boot all i see is the samsung logo, then it goes straight to cwm recorvery. I can also get into download mode. so I can get into cwm but my recovery is on my micro sd and it can't mount it. (i did a nandroid backup but it doesn't benefit me now. i also have to backup on my pc, but my pc doesn't wanna recognize it) did i brick it??
what i did...went into cwm wipe data/factory reset and wiped it. next > mounts and storage and clicked format system, and formatted it. then last i wiped dalvik cache. then i went to flash the rom (CM9) and it didn't flash. (because i had extracted it on the pc. it no longer was a .zip) don't know what i was thinkin' but yeah...
as of now i'm gonna start looking for threads to fix it.
i don't think samsung kies is working right either. :/ http://i.imgur.com/WV0iBPk.jpg
please help me unbrick it or whatever i need to do. only made one small mistake and now all this... :'( if you know anything about how to fix it pls reply. i need all the help i can get. thanks ...
Click to expand...
Click to collapse
Easy, bro. Does your current CWM recovery have a "sideload" option? Look for that either in the main menu or in the "install zip from sdcard" section. If you have that, then you could try sideloading a ROM directly from your PC to your device and it will flash automatically. For more instructions, just Google "ADB sideload".
If that doesn't cut it... Grab Odin and a stock GB firmware (these should be floating around in Dev section), flash that by Odin, and your Player gets returned to GB stock condition, where you can start over.
Sent from Google Nexus 4 @ CM11
AndyYan said:
Easy, bro. Does your current CWM recovery have a "sideload" option? Look for that either in the main menu or in the "install zip from sdcard" section. If you have that, then you could try sideloading a ROM directly from your PC to your device and it will flash automatically. For more instructions, just Google "ADB sideload".
If that doesn't cut it... Grab Odin and a stock GB firmware (these should be floating around in Dev section), flash that by Odin, and your Player gets returned to GB stock condition, where you can start over.
Sent from Google Nexus 4 @ CM11
Click to expand...
Click to collapse
no it doesn't have a sideload option anywhere. i have odin. and for the firmware, doesn't it have to be in the .tar form for odin to flash it?? i'll check that out. btw thanks !!
but the computer doesn't wanna recognize my device. so how can i flash anything??
EDIT do you think i could flash my nandroid backup through odin?? it has .tar files and one .md5 file, but 2 that aren't. i'll post a screen shot. but if i flash each of the .tar files and the .md5 file via odin do you think it would work? that file is only a .md5 though and not a .tar.md5 so idk
Austin68 said:
no it doesn't have a sideload option anywhere. i have odin. and for the firmware, doesn't it have to be in the .tar form for odin to flash it?? i'll check that out. btw thanks !!
but the computer doesn't wanna recognize my device. so how can i flash anything??
EDIT do you think i could flash my nandroid backup through odin?? it has .tar files and one .md5 file, but 2 that aren't. i'll post a screen shot. but if i flash each of the .tar files and the .md5 file via odin do you think it would work? that file is only a .md5 though and not a .tar.md5 so idk
Click to expand...
Click to collapse
No, nandroid backups won't be recognized by Odin. Just try finding a stock firmware out there. If you want your data back from your nandroid backup, you can always restore everything to normal first, then restore that nandroid and do whatever you please.
Sent from Google Nexus 4 @ CM11