I am trying to flash the new FXP rom on my Xperia P but i keep getting this error :
Code:
format() expects 4 args, got 5
E:Error in 'location of the zip file comes here'
(Status 7)
Any idea on how to fix this ??
I have CWM-based recovery v6.0.1.2 by [email protected]
Open the updater script and delete the first 3 lines that say LT22i. Then flash again
Sent from my ST25i using Tapatalk 2
You have wiped system.
Do never wipe system. It is used to verify that you are trying to install it on the correct device.
Rapier07 said:
Open the updater script and delete the first 3 lines that say LT22i. Then flash again
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
that doesnt work
DavidMKD said:
that doesnt work
Click to expand...
Click to collapse
Go to "CWM"->"install zip from sdcard"->"toggle signature verification".
Then try to install the edited ROM.
hnl_dk said:
Go to "CWM"->"install zip from sdcard"->"toggle signature verification".
Then try to install the edited ROM.
Click to expand...
Click to collapse
still the same error. I tried that even when I had the first error.
DavidMKD said:
still the same error. I tried that even when I had the first error.
Click to expand...
Click to collapse
The first error is because system has been wiped, so it will only help, if the assert has been removed.
What you could do, is to try to temporarily install a ROM, that does not check for what device it is installed on.
When that is done, are you able to install the FXP ROM, as the other one will setup a new system partition.
What did he exactly wrong ?
It should be?
Wipe cache
Wipe dalvik cache
Format system
Install fxp
Enjoy
Thx
thebrainkafka said:
What did he exactly wrong ?
It should be?
Wipe cache
Wipe dalvik cache
Format system
Install fxp
Enjoy
Thx
Click to expand...
Click to collapse
You may not wipe/format system.
The installation does need system, so make sure that it is installed on the correct phone.
So never wipe/format system yourself.
If it is needed, will the install script do it by itself, when it is needed.
Ok, and there are no issue with older files Which maybe not cleared during Installation when going from gb to ics?
Thx
Hello, I have the same issue, if it can help I solve it by replace the "update-binary" with one I take in a Rom which install well
Excuse for my english.
This may hep you
sau94 said:
I am trying to flash the new FXP rom on my Xperia P but i keep getting this error :
Code:
format() expects 4 args, got 5
E:Error in 'location of the zip file comes here'
(Status 7)
Any idea on how to fix this ??
I have CWM-based recovery v6.0.1.2 by [email protected]
Click to expand...
Click to collapse
I had the same problem when I was flashing MIUI rom weekly update to my Galaxy S3.
When I had this error, I was using CWM Recovery then I flashed Philz Recovery.
I tried to flash ROM again, and It was OK.
I hope, it works for you, too.
oOWeaponXOo said:
Hello, I have the same issue, if it can help I solve it by replace the "update-binary" with one I take in a Rom which install well
Excuse for my english.
Click to expand...
Click to collapse
i got some problem too.. can u explain more details? replace "update-binary" from stock ICS rom or from other rom? my device st25i (xperia u) with xnovathor 4.4.2 Custom rom, i would down grading to Xmiui v4 ICS.
hi =) i know maybe its late but ot end this problem and to let know how to solve to anyway will got this issue the solution is to check ,before flashing the zip, the box to allow the installation of old binaries, it works with an i8260
Related
PREVIEW
Alright, here is the official preview :
DOWNLOAD
And here is the CWM flashable zip file :
DOWNLOAD
Click to expand...
Click to collapse
Instuctions:
1) Reboot into CWM recovery
2) Choose "Install zip from SD card"
3) Locate to "CM9-bootanimation_Neo(V)-CWM" file
4) Flash it
5) Reboot phone
-) Enjoy!
Credits:
CyanogenMod team
I only made it a flashable zip, so that everyone can have it without installing CM.
Because I can reserve it.
For stock rom ?
Edit-nvm works great on stock rom,thanks
leajian said:
Because I can.
Click to expand...
Click to collapse
It's not exactly hard tho
Credits "cmTeam"
Sent from my MT15i using Tapatalk
Misunderstand!
kormatoes said:
It's not exactly hard tho
Credits "cmTeam"
Sent from my MT15i using Tapatalk
Click to expand...
Click to collapse
No, you misunderstood me... The "Because I can." comment it's for reserving the post for future use. xP
Of course ALL credits go to CyanogenMod team, if you flash it, you'll see that I credit them, but I forgot to mention it here.
Thanks for pointing that out!
Yhm, shoult it work on ICS?
While I tried flashing it using recovery, I got "Installation aborted" and info, that it was due to some parameters needed by mounting partition (required 3, got 4 or required 4, got 3 - i can't remember now but sth like that). Can you tell me what to provide (are there any logs from the recovery? ) to help you solve this
BTW, I just love this bootanimation, can't wait until CW9 will be released stable for my Neo V...
przemo_pl said:
Yhm, shoult it work on ICS?
While I tried flashing it using recovery, I got "Installation aborted" and info, that it was due to some parameters needed by mounting partition (required 3, got 4 or required 4, got 3 - i can't remember now but sth like that). Can you tell me what to provide (are there any logs from the recovery? ) to help you solve this
BTW, I just love this bootanimation, can't wait until CW9 will be released stable for my Neo V...
Click to expand...
Click to collapse
Try mount system.
Or manually copy and paste it to system/media/bootanimation and change permission
Sent from my Xperia Neo using XDA
will it work on stock roms?
will this only work on the xperia?
froichemarv said:
will it work on stock roms?
Click to expand...
Click to collapse
adoramlalezari said:
will this only work on the xperia?
Click to expand...
Click to collapse
It will work on any ROM or Stock.
Sent from my Sony Xperia Neo V using xda premium
This works for locked bootloaders too im guessing right ?
Ixtilion said:
This works for locked bootloaders too im guessing right ?
Click to expand...
Click to collapse
Yep I said!
Sent from my Sony Xperia Neo V using xda premium
Error
I get this error when I try to flash this:
* Miunting system...
mount() expects 4 args, got 3
E:Error in /sdcard/Download/CM9-bootanimation_Neo(V)-CWM.zip
(Status 7)
Installation aborted.
Installation Aborted
Hi I am unable to install the boot animation same error as above.. Pls help!!
thnx
Unable to install
renamed the file to bootanimation.zip and then copied it to /system/media changed the permissions to rw-r-r rebooted the phone and now there is no boot animation.
Also tried flashing it but same error
* Mounting system...
mount() expects 4 args, got 3
E:Error in /sdcard/Download/CM9-bootanimation_Neo(V)-CWM.zip
(Status 7)
Installation aborted.
Xperia Arc
I found two different versions of the newer Boot animation (featuring CID as opposed to Andy).
Flashed one that worked perfectly (however resolution was way out) the was able to replace it in system/media with the correct animation.
I think some builds are a little picky about changing the boot animation, but flash a working one it opens it up to the old bait and switch in the system/media folder.
If i can retrace my steps I wi edit this to state the exact files I used, and give proper recognition.
It doesn't work. I try it with clear dalvik and system. Mount system etc. but everytime the same message:
mount() expects 4 args, got 3
E:ERROR/sdcard/folder_of_my_files.zip
(Status 7)
Installation aborted.
Please help?
Hey it doesnt work
Sent from my ST18i using xda premium
Hello!
How can I wipe Dalvik Cache before install custom ROM, when I dont have advanced option in recovery mode?
Model: Spice Mi-350n
Thanks!
James9 said:
Hello!
How can I wipe Dalvik Cache before install custom ROM, when I dont have advanced option in recovery mode?
Model: Spice Mi-350n
Thanks!
Click to expand...
Click to collapse
Do you have a custom recovery such as clockworkmod recovery or TWRP installed? If not the only way to whipe dalvik cache is to do a factory reset in the stock recovery. Before you install a custom ROM you should install a custom recovery.
Sent from my SCH-I535 using xda premium
shimp208 said:
Do you have a custom recovery such as clockworkmod recovery or TWRP installed?
Sent from my SCH-I535 using xda premium
Click to expand...
Click to collapse
no, thanks I will try it...
shimp208 said:
Do you have a custom recovery such as clockworkmod recovery or TWRP installed? If not the only way to whipe dalvik cache is to do a factory reset in the stock recovery. Before you install a custom ROM you should install a custom recovery.
Sent from my SCH-I535 using xda premium
Click to expand...
Click to collapse
well, I installed rom manager from clockworkmod, press reboot to recovery mode and I have same menu as before, without that advanced option...
James9 said:
well, I installed rom manager from clockworkmod, press reboot to recovery mode and I have same menu as before, without that advanced option...
Click to expand...
Click to collapse
Check out this guide to installing Clockworkmod Recovery for your phone as well as custom ROM's you can put on it. Here is another guide as well for installing a custom ROM make sure you check out the first guide I mentioned though first. Hope this helps .
shimp208 said:
Check out this guide to installing Clockworkmod Recovery for your phone as well as custom ROM's you can put on it. Here is another guide as well for installing a custom ROM make sure you check out the first guide I mentioned though first. Hope this helps .
Click to expand...
Click to collapse
well, I was in that forum and created back up of stock ROM and I thought "RECOVERY" part was for recovering ROM, when something went wrong
so thx again and again, I am going on that!
James9 said:
well, I was in that forum and created back up of stock ROM and I thought "RECOVERY" part was for recovering ROM, when something went wrong
so thx again and again, I am going on that!
Click to expand...
Click to collapse
No problem man glad to help, but yes "recovery" is for recovering something when something with your ROM goes wrong, but it can also be used for basic maintenance functions such as reformatting things, as well as flashing certain scripts, kernels, mods etc.
shimp208 said:
No problem man glad to help, but yes "recovery" is for recovering something when something with your ROM goes wrong, but it can also be used for basic maintenance functions such as reformatting things, as well as flashing certain scripts, kernels, mods etc.
Click to expand...
Click to collapse
so I wiper out everything going on harder part instaling new ROM
it tells me:
finding update package...
opening update package..
verifying update package...
E:No signature
E:verification failed
zip verification failed
zip isnt signed correctly
instalation aborted
it´s this ROM
James9 said:
so I wiper out everything going on harder part instaling new ROM
it tells me:
finding update package...
opening update package..
verifying update package...
E:No signature
E:verification failed
zip verification failed
zip isnt signed correctly
instalation aborted
it´s this ROM
Click to expand...
Click to collapse
well I found there option: toggle verification )) and now finally installing
I´m curious what problem will be next
James9 said:
so I wiper out everything going on harder part instaling new ROM
it tells me:
finding update package...
opening update package..
verifying update package...
E:No signature
E:verification failed
zip verification failed
zip isnt signed correctly
instalation aborted
it´s this ROM
Click to expand...
Click to collapse
You installed CWM (Clockworkmod Recovery correct?) if you did go under "install zip from sdcard", then "toggle signature verification" and it make sure it says signature check: disabled this should allow you to flash the ROM.
shimp208 said:
You installed CWM (Clockworkmod Recovery correct?) if you did go under "install zip from sdcard", then "toggle signature verification" and it make sure it says signature check: disabled this should allow you to flash the ROM.
Click to expand...
Click to collapse
yes, I found out that an now I am trying to download something from Google play, but it doesnt work...
at old ROM I had android market and everything was fine...
can you tell me why doesnt work google play? it only writes downloading and nothing more...
James9 said:
yes, I found out that an now I am trying to download something from Google play, but it doesnt work...
at old ROM I had android market and everything was fine...
can you tell me why doesnt work google play? it only writes downloading and nothing more...
Click to expand...
Click to collapse
Try running the fix permission utility in ROM manager, see if that solves your problem. You should also be able to use CWM recovery to fix permissions as well.
shimp208 said:
Try running the fix permission utility in ROM manager, see if that solves your problem. You should also be able to use CWM recovery to fix permissions as well.
Click to expand...
Click to collapse
no it didnt help
we can continue here
James9 said:
no it didnt help
we can continue here
Click to expand...
Click to collapse
*moved to new discussion thread*
Hi,
I've been trying to install CM 11 based on Kitkat 4.4.2 on my Xperia P. The following are the details / steps followed:
- The bootloader is unlocked
- The phone is rooted
- CWM 6.0.1.2 is installed ( I think this is the latest available for Xperia P)
1) Downloaded CM11-RC1 from the links in this thread http://forum.xda-developers.com/showthread.php?t=2626639
2) Modified 'updater-script' to get rid of Error 7
3) Extracted 'boot.img' and flashed it using FlashTool in fastboot mode.
After reboot, the phone stops at Sony logo and vibrates once.
4) Pressed the Power button to load CWM Recovery
5) Wiped Data, Cache/Partition, Dalvik Cache
6) Tried to install CM11-RC1 zip file using CWM
Now I get the message "Installation aborted", as soon as the installation begins, without any error code being displayed
I can't seem to get past this step, and don't know where I'm going wrong.
Can anyone please help me out?
Are you sure that your phone is unlocked bootloader ? Did you unlocked yourself ? And you should not change anything in update script because i had flash this rom without problem ...
Sent from my Xperia P using Tapatalk 2
-ss- said:
Are you sure that your phone is unlocked bootloader ? Did you unlocked yourself ? And you should not change anything in update script because i had flash this rom without problem ...
Sent from my Xperia P using Tapatalk 2
Click to expand...
Click to collapse
Yes. The bootloader is unlocked. I did it myself following the instructions on the Sony website.
The installation shows an error 7 if I don't modify the updater script.
Delete sorry
Sent from my Xperia P using Tapatalk
yomayne said:
Yes. The bootloader is unlocked. I did it myself following the instructions on the Sony website.
The installation shows an error 7 if I don't modify the updater script.
Click to expand...
Click to collapse
What i have done with flashing this rom was just followed the OP : format system, format data and format catch then flash ROM and gapps without problem ...
Sent from my Xperia P using Tapatalk 2
-ss- said:
What i have done with flashing this rom was just followed the OP : format system, format data and format catch then flash ROM and gapps without problem ...
Sent from my Xperia P using Tapatalk 2
Click to expand...
Click to collapse
Could it be a version issue? Which one did you flash? I did RC1
Hey I had exactly the same problem. What I did was this:
I used Sony Mobile EMMA to re-install latest stock firmware.
After that I rooted it and Installed CWM 1.0 Nypon, I believe this is CWM somewhere in V6.xxxx (other versions wouldn't work for me..)
I also edited the updater script because it wouldn't pass the assert section, so I deleted this.
After that Recompiled it, (Zip format ofcourse) and copied it to SD card.
Next, I flashed boot.img and rebooted the phone after that. Then access CWM.
Now what I did was userdata/factory reset after that I deleted cache, and last but not least dalvik cache.
After that I flashed the recompiled ROM file and then It passed the status 7 error.
When that was finished I flashed gapps
This was what I did, becuz' I had exactly the same problem. I don't know if this works for you but you might give it a try.
(Sorry for bad Englisch)
(Make sure that your bootloader is unlocked! (To verify, I did try to unlock it again. Then I got a message saying that it was allready unlocked)
ReplayMitta said:
Hey I had exactly the same problem. What I did was this:
I used Sony Mobile EMMA to re-install latest stock firmware.
After that I rooted it and Installed CWM 1.0 Nypon, I believe this is CWM somewhere in V6.xxxx (other versions wouldn't work for me..)
I also edited the updater script because it wouldn't pass the assert section, so I deleted this.
After that Recompiled it, (Zip format ofcourse) and copied it to SD card.
Next, I flashed boot.img and rebooted the phone after that. Then access CWM.
Now what I did was userdata/factory reset after that I deleted cache, and last but not least dalvik cache.
After that I flashed the recompiled ROM file and then It passed the status 7 error.
When that was finished I flashed gapps
This was what I did, becuz' I had exactly the same problem. I don't know if this works for you but you might give it a try.
(Sorry for bad Englisch)
(Make sure that your bootloader is unlocked! (To verify, I did try to unlock it again. Then I got a message saying that it was allready unlocked)
Click to expand...
Click to collapse
Thanks. I'll try doing that. Let's see if it works. Which CM11 build did you flash?
yomayne said:
Thanks. I'll try doing that. Let's see if it works. Which CM11 build did you flash?
Click to expand...
Click to collapse
I flashed RC1 also, I tried almost all nightly's and the RC1 lol but they all wouldn't work before I used this sort of 'method'
Yesterday RC1 workied succesfully for me, today I updated to nightly 25 and everything works fine. Note that once you get passed the installation of RC1, that you can only access the CWM recovery with holding the power button, when your phone vibrates when you see the sony logo.. The CW11 comes with CMW touchable. Goodluck
And did it work?
I've solved my status 7 problem with this video ;
http://www.youtube.com/watch?v=QW1znjDLe-k
gilgin said:
I've solved my status 7 problem with this video ;
http://www.youtube.com/watch?v=QW1znjDLe-k
Click to expand...
Click to collapse
Auful way way to "fix" things.
You can "fix" galaxy ROM to be installed on your phone and brick it permanently, it's already been done.
If you have flashed galaxy kernel you probably won't be able to boot but still able to recover.
Tha asserts are there for a reason.
ChikeD said:
Auful way way to "fix" things.
You can "fix" galaxy ROM to be installed on your phone and brick it permanently, it's already been done.
If you have flashed galaxy kernel you probably won't be able to boot but still able to recover.
Tha asserts are there for a reason.
Click to expand...
Click to collapse
I didn't flash a wrong kernel or rom. İf friend is sure of the right pack to flash, than he can use this method.
I wanted to flash cm nightly 25 (percy's rom) to my xperia p, and the cwm gave status 7 error. Then i have searched a solution for my problem, and i found this video and did what he shows in the video, and i have a cm11 flashed xperia p now. And i also flashed over cm11-weekly.
(sorry if i have a bad english)
gilgin said:
I didn't flash a wrong kernel or rom. İf friend is sure of the right pack to flash, than he can use this method.
I wanted to flash cm nightly 25 (percy's rom) to my xperia p, and the cwm gave status 7 error. Then i have searched a solution for my problem, and i found this video and did what he shows in the video, and i have a cm11 flashed xperia p now. And i also flashed over cm11-weekly.
(sorry if i have a bad english)
Click to expand...
Click to collapse
Sp they released a ROM that cannot be flushed, is that what you say? And no one else reporting it?
Somehow I find it difficult to believe.
If you have followed the instructions I'm sure there would be no problem, or the instructions are incomplete, or there is some issue, either way it's up to the developer to fix it.
Avoid "fixing" errors in this manner or one day you may regret it dearly.
ChikeD said:
Sp they released a ROM that cannot be flushed, is that what you say? And no one else reporting it?
Somehow I find it difficult to believe.
If you have followed the instructions I'm sure there would be no problem, or the instructions are incomplete, or there is some issue, either way it's up to the developer to fix it.
Avoid "fixing" errors in this manner or one day you may regret it dearly.
Click to expand...
Click to collapse
I have followed the instructions in a good way and this was the problem i have lived. Some of my friends lived this problem in a Turkish Forum and i recommended this way, they did it and flash the rom. I will give the link here; http://forum.donanimhaber.com/m_58138440/mpage_242/f_//tm.htm#87204228
My nick is ENG_civ on that forum. Everything is right about the rom but something goes in a wrong way, so this way makes the compiler not asking "is this right rom?", that's all. İn my opinion, if you are sure of the rom, there is no risk.
And i am new in this forum, and i couldn't write at development part, and this is the first time i am writing to a foreign language forum. So i couldn't reported them, and these rom's are not the final, so there could be faults on them i think.
gilgin said:
I've solved my status 7 problem with this video ;
(video)
Click to expand...
Click to collapse
I solved the problem with the CM11 this way too. But when I tried to install gapps after install cm11 appear the "status 7". What can I do?
Edit: I can flash the normal cm11 (without edit the .txt) but the problem with the gapps continues. I turned on my phone and then the cyanogenmod logo start running and don't leave this screen. Anyone can help me?
Error:
set_metadata_recursive: some changes failed
E:Error in /storage/sdcard0/gapps-kk-20140105.signed.zip (status 7)
Installation aborted.
nortonz said:
I solved the problem with the CM11 this way too. But when I tried to install gapps after install cm11 appear the "status 7". What can I do?
Edit: I can flash the normal cm11 (without edit the .txt) but the problem with the gapps continues. I turned on my phone and then the cyanogenmod logo start running and don't leave this screen. Anyone can help me?
Error:
set_metadata_recursive: some changes failed
E:Error in /storage/sdcard0/gapps-kk-20140105.signed.zip (status 7)
Installation aborted.
Click to expand...
Click to collapse
For gapps its normal. Its actually flashed
Sent from my Xperia P using Tapatalk
AndroidNoob69 said:
For gapps its normal. Its actually flashed
Sent from my Xperia P using Tapatalk
Click to expand...
Click to collapse
How "normal" ?
PS: now my celphone has cyanogenmod 11 ! I'm so glad and grateful for this post!
nortonz said:
How "normal" ?
Click to expand...
Click to collapse
'normal' as in everyone has it. The zip is actually flashed.
Sent from my Xperia P using Tapatalk
It worked!
Thanks so much ! I'm finally running 4.4.2
hi all, i'm trying to install cm 11(weekly7) nypon on Xperia P...bootloader unlocked, rooted, cwm 6.0.1.2.
i've done fastboot kernel of cyano but when i go to recovery and i start to install cyano, it gives me error status 7 installation aborted, and above there's repeated "getprop,ecc.."(i think the error is it here). could anyone help me, please?
Federicogs3 said:
hi all, i'm trying to install cm 11(weekly7) nypon on Xperia P...bootloader unlocked, rooted, cwm 6.0.1.2.
i've done fastboot kernel of cyano but when i go to recovery and i start to install cyano, it gives me error status 7 installation aborted, and above there's repeated "getprop,ecc.."(i think the error is it here). could anyone help me, please?
Click to expand...
Click to collapse
Delete the assert lines from your updater script
Update to a newer version of recovery since older recoveries don't support selinux.
Regards
MasterAwesome
MasterAwesome said:
Delete the assert lines from your updater script
Update to a newer version of recovery since older recoveries don't support selinux.
Regards
MasterAwesome
Click to expand...
Click to collapse
thanks, but i can't find a newer cwm...can you help me?
Federicogs3 said:
thanks, but i can't find a newer cwm...can you help me?
Click to expand...
Click to collapse
If your current recovery gives status 7 that means your recovery is good To go... Try deleting the asset statements in the top of updater script.
Regards
MasterAwesome
unfortunatly the phone doesn't restart the system because of cyano kernel, i've recover stock rom and i'll repeat all the procedures!
It's taking too longer to save the modified "updater script"...more than 30 minutes and it stills going on!
edit: i've downloaded zipplus because winzip gets stuck, now there's no problem and cyano is fantastic! thanks #MasterAwesome
Federicogs3 said:
unfortunatly the phone doesn't restart the system because of cyano kernel, i've recover stock rom and i'll repeat all the procedures!
It's taking too longer to save the modified "updater script"...more than 30 minutes and it stills going on!
edit: i've downloaded zipplus because winzip gets stuck, now there's no problem and cyano is fantastic! thanks #MasterAwesome
Click to expand...
Click to collapse
No problem.. I'm here to help
Regards
MasterAwesome
I wanted to update the OS of my i5500. I first tried the method here but the phone got stuck in bootloop. Then, I attempted to install the version here. Still bootloop. Can you guys help me? I can't use my phone anymore.
Flash the recovery (CWM) again and format /system , /data and /cache . Then flash the packages mentioned in the second link (which is better than the first, if you ask me).
Vagelis1608 said:
Flash the recovery (CWM) again and format /system , /data and /cache . Then flash the packages mentioned in the second link (which is better than the first, if you ask me).
Click to expand...
Click to collapse
Just did it. Still bootloop.
mertcanhekim said:
Just did it. Still bootloop.
Click to expand...
Click to collapse
Try flashing CM11 from madteam.co
I'm having difficulty finding the right version of CM11 for my phone since madteam.co is inaccessable due to database errors. Do you know somewhere else I can download it?
Vagelis1608 said:
Try flashing CM11 from madteam.co
Click to expand...
Click to collapse
Madteam.co is no more
mertcanhekim said:
I'm having difficulty finding the right version of CM11 for my phone since madteam.co is inaccessable due to database errors. Do you know somewhere else I can download it?
Click to expand...
Click to collapse
Found some days ago a mirror, there are links to Google Drive pages with CM11 and Gapps here
http://vinloren.blogspot.it/?m=1
Inviato dal mio Nexus 5 con Tapatalk 2
jacomail95 said:
Found some days ago a mirror, there are links to Google Drive pages with CM11 and Gapps here
http://vinloren.blogspot.it/?m=1
Click to expand...
Click to collapse
Finding update package...
Opening update package...
Installing update...
E:Error in /sdcard/cm-11.0.0-GT-I5500-galaxy5.zip
(Status 0)
Installation aborted.
I did not understand how to use recovery-clockworkmod-6.0.5.2 so I tried installing with ClockworkMod-Galaxy5-v0.7 . Most likely that is why it failed.
What am I supposed to do with recovery-clockworkmod-6.0.5.2 file? It's not in .tar format so Odin does not accept it. The page is not in English and I did not understand.
mertcanhekim said:
Finding update package...
Opening update package...
Installing update...
E:Error in /sdcard/cm-11.0.0-GT-I5500-galaxy5.zip
(Status 0)
Installation aborted.
I did not understand how to use recovery-clockworkmod-6.0.5.2 so I tried installing with ClockworkMod-Galaxy5-v0.7 . Most likely that is why it failed.
What am I supposed to do with recovery-clockworkmod-6.0.5.2 file? It's not in .tar format so Odin does not accept it. The page is not in English and I did not understand.
Click to expand...
Click to collapse
It's flashable. Flash it in recovery. Then reboot into recovery (so that the new recovery gets loaded).
Also, you have to flash it in order to able to use the ROM.
Vagelis1608 said:
It's flashable. Flash it in recovery. Then reboot into recovery (so that the new recovery gets loaded).
Also, you have to flash it in order to able to use the ROM.
Click to expand...
Click to collapse
I understood very little from that. You mean I need another recovery? I know only clockworkmod that is applicable to my phone.
mertcanhekim said:
I understood very little from that. You mean I need another recovery? I know only clockworkmod that is applicable to my phone.
Click to expand...
Click to collapse
You have an old CWM. Using that old CWM install the flashable zip of the new CWM then reboot. Simple
mertcanhekim said:
I understood very little from that. You mean I need another recovery? I know only clockworkmod that is applicable to my phone.
Click to expand...
Click to collapse
Flash clockwordmod-6.0.5.2 in recovery (like a ROM). Then reboot. Then flash the ROM.
jacomail95 said:
You have an old CWM. Using that old CWM install the flashable zip of the new CWM then reboot. Simple
Click to expand...
Click to collapse
Thanks. When you put it that way I understood clearly.
I installed CM11 and this time instead of the word Android the Cyanogenmod logo appeared and for a second I thought it really worked. Then, the scumbag phone decided to go into a bootloop.
:crying:
mertcanhekim said:
Thanks. When you put it that way I understood clearly.
I installed CM11 and this time instead of the word Android the Cyanogenmod logo appeared and for a second I thought it really worked. Then, the scumbag phone decided to go into a bootloop.
:crying:
Click to expand...
Click to collapse
Did you wipe /data after flashing the ROM?
Vagelis1608 said:
Did you wipe /data after flashing the ROM?
Click to expand...
Click to collapse
I wiped data, wiped cache, and wiped dalvik cache all BEFORE flashing the ROM. I was supposed to do it after? Wouldn't that delete the installed data of the ROM?
I tried wiping data AFTER flashing the ROM. It bootloops the exact same way.
mertcanhekim said:
I tried wiping data AFTER flashing the ROM. It bootloops the exact same way.
Click to expand...
Click to collapse
How did you get into recovery?
Vagelis1608 said:
How did you get into recovery?
Click to expand...
Click to collapse
You mean AFTER flashing the Rom? I was already in recovery to flash the Rom so I wiped /data before rebooting. Was I supposed to reboot first?
mertcanhekim said:
You mean AFTER flashing the Rom? I was already in recovery to flash the Rom so I wiped /data before rebooting. Was I supposed to reboot first?
Click to expand...
Click to collapse
No. After the bootloop, how did you get in recovery?
Vagelis1608 said:
No. After the bootloop, how did you get in recovery?
Click to expand...
Click to collapse
1- I loaded clockworkmod 6.0.1.2 with Odin
2- I flashed clockworkmod 6.0.5.2
3- I wiped data, cache, and dalvik cache
4- I flashed CM11 again
5- I wiped data again
6- Rebooted
Bootloop happened once more.