Hboot downgrade.does everything works ? - HTC EVO 3D

Hello.
I used the wire Trick.
My hboot Version is 1.53.0007
S-off.
I would like to downgrade my hboot to 1.49. And use revolutionary to unlock.
Can i downgrade to that hboot and flash newest Radio/ Firmware without Problems?
Why do i want to do that?
Becouse it is the only way to flash cm Roms.
After i do that can i flash ics custom Roms without Problems?
Does someone has a Download Link for 1
.49. Hboot ?
Sent Form my HTC EVO3D using my big fat fingers.

I think you can do that (I'm CDMA so ours is a little different). You could do the write trick and then downgrade your hboot after you get s-off. I think that would be easier.
Edit: I can't read.
Read, Search, Read again, ... Then Ask with Tapatalk 2

coal686 said:
I think you can do that (I'm CDMA so ours is a little different). You could do the write trick and then downgrade your hboot after you get s-off. I think that would be easier.
Read, Search, Read again, ... Then Ask with Tapatalk 2
Click to expand...
Click to collapse
I have allready done the wire Trick.
S off too.
The question is when i downgrade the hboot are there eny Problems with that hboot and ics custom roms or do i only need to flash ics Firmware and no Problems?
Sent Form my HTC EVO3D using my big fat fingers.

Runlevel5 said:
I have allready done the wire Trick.
S off too.
The question is when i downgrade the hboot are there eny Problems with that hboot and ics custom roms or do i only need to flash ics Firmware and no Problems?
Sent Form my HTC EVO3D using my big fat fingers.
Click to expand...
Click to collapse
Duh. I misread your OP. Afaik, that hboot will allow you to install the ICS custom roms too, but you may want to wait for a GSM user to confirm. Or try it and if not, you can always revert back. The beauty of being s-off.
Read, Search, Read again, ... Then Ask with Tapatalk 2

coal686 said:
Duh. I misread your OP. Afaik, that hboot will allow you to install the ICS custom roms too, but you may want to wait for a GSM user to confirm. Or try it and if not, you can always revert back. The beauty of being s-off.
Read, Search, Read again, ... Then Ask with Tapatalk 2
Click to expand...
Click to collapse
For that i need to Download hboot 1.49 and hboot 1.53 so if something goes wrong i can flash 1.53 and dont need to install RUU.
Hope someone has this 2 hboots so i can try it.
My only hope is that hboot 1.49 works with newest Firmware and i can flash ics custom Roms without reboots and Problems.
What i want to Do is.
Downgrade to 1.49
Unlock with recolutionary
Flash newest Firmware and flash and use eny custom Rom i want
Sent Form my HTC EVO3D using my big fat fingers.

I have a gsm evo my hboot is 1.49 and I can flash ics sense 3.6 and sense 4 roms without any issue, hope that helps
sent on my Evil Evo running the special sauce kernel

flashallthetime said:
I have a gsm evo my hboot is 1.49 and I can flash ics sense 3.6 and sense 4 roms without any issue, hope that helps
sent on my Evil Evo running the special sauce kernel
Click to expand...
Click to collapse
Offcourse it helps.
Thx for that.
Sent Form my HTC EVO3D using my big fat fingers.

Related

Boot loop on all ics roms

I keeping getting a bootloop on all ics roms and I tried a kernal that someone recommend but it kills my 3d and i get random reboots . Is there any way to fix this problem and install the ROM with everything working. I'm on hb 1.50 . S- on . Or is there a way to downgrade to hb 1.40 but i don't have a Linux . What's the easiest way ?
Sent from my PG86100 using XDA
I also get the same results!
You can always try 4EXT Recovery with smartflash on. It works for both S-On and S-Off
ccr515 said:
I keeping getting a bootloop on all ics roms and I tried a kernal that someone recommend but it kills my 3d and i get random reboots . Is there any way to fix this problem and install the ROM with everything working. I'm on hb 1.50 . S- on . Or is there a way to downgrade to hb 1.40 but i don't have a Linux . What's the easiest way ?
Sent from my PG86100 using XDA
Click to expand...
Click to collapse
try a superwipe. that fixed mine. Look in the dev forum for it (i think you can find it in the mean rom thread)
You could also downgrade using the instructions in the development thread. Ir doesnt require Linux, it includes a downloadable bootable CD. ITA damn near an automated process minus the brick part. And +1 for 4ext recovery it has features built just for S-on.
My other shooter is an FNAR .308
I already tired a super wipe and my netboot doesn't have a cd drive .
Sent from my PG86100 using XDA
Try using any of Chad.Goodman's ICS Kernel after flashing an ICS ROM
1) DO THIS AT YOUR OWN RISK
2) USE THE RIGHT KERNEL
*credit to chad.goodman* http://forum.xda-developers.com/showthread.php?t=1623646
That the kernal that I already use . It breaks my 3d and i get random reboots
Sent from my PG86100 using XDA
ccr515 said:
That the kernal that I already use . It breaks my 3d and i get random reboots
Sent from my PG86100 using XDA
Click to expand...
Click to collapse
Well what kernel did you use, you could be flashing the wrong one. The other option is to downgrade HBOOT ,, no linux required
http://forum.xda-developers.com/showthread.php?t=1563342
---------- Post added at 08:10 PM ---------- Previous post was at 07:49 PM ----------
I got my ICS ROM to work by flashing RLS1
I doubt downgrading HBOOT will help, he's getting it to work with Chad's kernel. I'm exhibiting the exact same issue with bootloops with the stock kernel(in my case I used the shooter ice kernel to get it to boot) and I'm S-OFF/GSM so I'm pretty sure the issue isn't HBOOT related.
Same here
I have the same issue. I use 4ext with smartflash for recovery. I'm able to flash any GB rom I want, but when I try an ICS rom with a stock kernel I get the boot looping. Is there any other way to make this work? I don't want to dig into the brick/unbrick business if I can help it. I have also tried using Flash Img GUI and fastboot/adb to flash the kernel with the exact same results. Any information on this would help, but a solution would be fantastic!
._. I see what's going on... It's GSM users trying to flash CDMA kernels once again.
Sent from my PG86100 using XDA
What I did was use the new s off for 1.50 and once I got that done I was able to flash any ics Rom I want . Look for it in the development section.
Sent from my PG86100 using XDA
ccr515 said:
What I did was use the new s off for 1.50 and once I got that done I was able to flash any ics Rom I want . Look for it in the development section.
Sent from my PG86100 using XDA
Click to expand...
Click to collapse
+1 to this. The stock Ics kernel does not do well with 1.5 s-on. Since you cannot downgrade to 1.4 s-off, you should try the new 1.5 s-off method. Otherwise you have to use a custom kernel which is not 100% yet.
Sent from my PG86100
coal686 said:
+1 to this. The stock Ics kernel does not do well with 1.5 s-on. Since you cannot downgrade to 1.4 s-off, you should try the new 1.5 s-off method. Otherwise you have to use a custom kernel which is not 100% yet.
Sent from my PG86100
Click to expand...
Click to collapse
Seems like no stock ics kernels like 1.4 hboot period with or without s-off. None would work for me until i updated my hboot to 1.5 and had s-off.
smokin1337 said:
Seems like no stock ics kernels like 1.4 hboot period with or without s-off. None would work for me until i updated my hboot to 1.5 and had s-off.
Click to expand...
Click to collapse
I've been running 1.4 s-off since the downgrade method came available and have never had an issue with any ics ROMs.
Sent from my PG86100
Can someone post a link to the new S-Off method for hboot 1.5?
MakeMeFibonacci said:
Can someone post a link to the new S-Off method for hboot 1.5?
Click to expand...
Click to collapse
Here it is: http://forum.xda-developers.com/showthread.php?t=1585846
I recommend you read all about it first as you have to connect two contact points on your phone using insulated wire, which sounds kind of dangerous.
coal686 said:
Here it is: http://forum.xda-developers.com/showthread.php?t=1585846
I recommend you read all about it first as you have to connect two contact points on your phone using insulated wire, which sounds kind of dangerous.
Click to expand...
Click to collapse
The hboot downgrade seems a lot less scary for sure. In all honesty it was ez and took me less than 30 mins but to each his own

[Q] S-off or S-on ?

What exactly are the benefits of gaining s-off ??
I am confused...i have a gsm evo 3d and some tutorials are of s-off and others s-on ?
What will be the best... i am a newbie at this !
Click Thanks if i helped !!
With S-OFF you can flash PG86IMG.zip files from SD card in bootloader (ICS firmware, radio...), also you don't have to always flash boot.img via fastboot after flashing of new ROM.
Forgot I something?
Benik3 said:
With S-OFF you can flash PG86IMG.zip files from SD card in bootloader (ICS firmware, radio...), also you don't have to always flash boot.img via fastboot after flashing of new ROM.
Forgot I something?
Click to expand...
Click to collapse
To add to this, s-on seems to not play well with ics. Most of the issues people have with ics not working right or bootlooping come from s-on users. I highly recommend s-off if possible.
Sent from my PG86100 using Tapatalk 2
invince2 said:
What exactly are the benefits of gaining s-off ??
I am confused...i have a gsm evo 3d and some tutorials are of s-off and others s-on ?
What will be the best... i am a newbie at this !
Click Thanks if i helped !!
Click to expand...
Click to collapse
Yeah, you should definitely go with the tutorials for S-OFF if you are flashing new Roms, and expertimenting with your phone. For the most ICS roms, you have to flash new firmware packages (PG86IMG.zip), and you can do this if you are S-OFF.
It means if i have s-on i can't flash every rom but if i gain s-off it allows full compatibilty?
Am i right ?
Click Thanks if i helped !!
Benik3 said:
With S-OFF you can flash PG86IMG.zip files from SD card in bootloader (ICS firmware, radio...), also you don't have to always flash boot.img via fastboot after flashing of new ROM.
Forgot I something?
Click to expand...
Click to collapse
Where exactly did u find the tutorial for s-off?
invince2 said:
It means if i have s-on i can't flash every rom but if i gain s-off it allows full compatibilty?
Am i right ?
Click Thanks if i helped !!
Click to expand...
Click to collapse
Absolutely correct. Not just compatibility with roms, but with every e3d addon.
Sent from my PG86100 using xda premium
invince2 said:
Where exactly did u find the tutorial for s-off?
Click to expand...
Click to collapse
Since you are GSM, look at the stickies in the GSM developmental forums.
Sent from my PG86100 using Tapatalk 2
I would say go with S-off. I had S-on and it took so much work to get new roms and it was just a pain in the butt. I am now running revolutionary S-off and am using 4ext recovery so i can easily put on new roms in just a few mins. I hope i helped.
Ah crap i just reported this thread for posting warez by goddamn mistake!
My bad
Keeping on topic: I'd say definitely S-off and there is loads of threads on how to do it. Just have a read through them all and try it out, ask for help if you need it and someone is bound to help
taylor308 said:
I would say go with S-off. I had S-on and it took so much work to get new roms and it was just a pain in the butt. I am now running revolutionary S-off and am using 4ext recovery so i can easily put on new roms in just a few mins. I hope i helped.
Click to expand...
Click to collapse
But 4ext recovery is available on s-on !
S off makes it easier to flash roms along with any kernel . Best route to go.
Sent from my PG86100 using xda premium
I have two EVO 3d's one is s-on and the other is s-off, both running 4ext touch recovery and both have the same experiance and the same battery life, no extra steps needed to flash roms or kernels..only thing is that only signed packages can be flashed through the bootloader, other than that...no difference.
S off is a life saver. It just is. No matter what HTC does if a dev can get s off for my device. I'm doing it.

[Q] Bootloops when flashing roms with hboot 1.4 s-off

I've been trying to flash some of these new roms such as Cool ICS and SolidRom MyUI, both to no avail. I am on h-boot 1.4 with s-off. The last successful rom I had running on the phone was ICS MIUI. I had tried flash these roms on ext4 initially, then I tried twrp and both without success. Any tips/suggestions to get one of these roms to work?
Do I need a newer h-boot in order to flash these newer roms with newer kernels? If so, then how/what do I flash without losing s-off?
Well here goes nothing...going to try jbear's 1.58 hboot.
I still get bootloop after installing Cool ICS...
Getting bootloop with SolidRom MyUI as well. Could use some help please.
RTC88 said:
Getting bootloop with SolidRom MyUI as well. Could use some help please.
Click to expand...
Click to collapse
Did you do a full wipe?
Sent from my Evo 3D GSM using xda app-developers app
Gmobilize said:
Did you do a full wipe?
Sent from my Evo 3D GSM using xda app-developers app
Click to expand...
Click to collapse
Yup, did a full wipe for prior to flashing every new rom. I have actually gotten SolidRom to work after installing the ICS firmware update img, but I still can't get Cool ICS to work.
RTC88 said:
Getting bootloop with SolidRom MyUI as well. Could use some help please.
Click to expand...
Click to collapse
If you are s-off then this should be easy to fix.
Some HBOOTs can only work for certain firmwares.
So if you want to run a ICS rom, you need to upgrade your hboot to either stock hboot 1.58, or Jbear's 1.58.5858
To upgrade your hboot, download the correct hboot from ramjet73's post here then rename the file to PG86IMG with the files extension as .ZIP
Place that on the root of your SDcard and boot into your bootloader. Accept the update, then restart your phone.
***EDIT***
I wasn't correct on some of the hboots and got some mixed up with the gsm EVO, for more info on hboots go to the link which ramjet73 has posted below.
I HOPED THIS HELPS!
MY PHONE
HTC EVO 3D
S-OFF and UNLOCKED
ROM: Team D.I.R.T. Unofficial AOKP v3.3
KERNEL: ButteredToasT-RLS v13.6
HBOOT: 1.40.0000
RECOVERY: 4EXT Touch Recovery
leogy101 said:
If you are s-off then this should be easy to fix.
Then there are the newer firmwares that everyone has been having a fit over, 1.50, 1.58.0000, 1.53, 1.58.5858 (this is the Juopunutbear's custom hboot)
Those are the hboots that run only SPRINT/VM ICS roms.
Click to expand...
Click to collapse
You might want to read through this thread to get the correct information on CDMA hboots. Most of those you mentioned are Sprint bootloaders (the only VM bootloaders are 1.57 and JBear 1.57.5757) but 1.53 is for GSM phones only.
ramjet73
ramjet73 said:
You might want to read through this thread to get the correct information on CDMA hboots. Most of those you mentioned are Sprint bootloaders (the only VM bootloaders are 1.57 and JBear 1.57.5757) but 1.53 is for GSM phones only.
ramjet73
Click to expand...
Click to collapse
Yeah, I figured I wasn't fully correct with some of the information. I'm gonna go to that thread you linked out and study. Thank you!
Leogy,

[Q] SPRINT EVO 3D KERNAL 2.89 Hboot 1.5858 JB???

I have the EVO 3D with the 2.89 RUU installed with HBOOT 1.5858 S-OFF
Is there anyway I can put a JB ROM on my phone?
I've read that JB is not compatible with 1.5858.
Downgrade to the 1.04 ENG Hboot (found in the lens_flare edition miui thread) and you'll be good to go
Sent from my PG86100 using Tapatalk 2
Sounds like you already know the answer.
He was probably looking for clarification
hboot downgrade
Well I've also read that I can downgrade my hboot to 1.4, but that I have to brick it to do that. In other forums people talk like downgrading to 1.4 is simple. When I got the 1.58 upgrade it updated all my radio filestoo.. So I'm wondering if those radioh files are stored on the same partition as hboot. If they are I know how to flash my hboot with fastboot flash command so that would be simple.. Any help, pointers or info would be greatly appreciated.
ZWYATT said:
Sounds like you already know the answer.
Click to expand...
Click to collapse
hboot 1.04
First thanks again.. Do you know if I can just flash this hboot w/o bricking the phone. A lot of people are saying that the phone needs to be bricked to downgrade.
beneath-a-burning-turtle said:
Downgrade to the 1.04 ENG Hboot (found in the lens_flare edition miui thread) and you'll be good to go
Sent from my PG86100 using Tapatalk 2
Click to expand...
Click to collapse
I see we have someone with common sense here thank you for explaining that!:good:
Jsparta26 said:
He was probably looking for clarification
Click to expand...
Click to collapse
frankk1979 said:
First thanks again.. Do you know if I can just flash this hboot w/o bricking the phone. A lot of people are saying that the phone needs to be bricked to downgrade.
Click to expand...
Click to collapse
Yes, since youre s-off, all you need to do is find a copy of the hboot ( pg86img.zip) and place it on your sdcard, and boot into the bootloader, the phone does everything else from there on its own
Sent from my Evo 3D CDMA using xda app-developers app
class
http://forum.xda-developers.com/showthread.php?t=1817513
You should be able to find all the info you need there.

[Q] What is a good ROM?

I have been looking for a JB ROM for my HTC EVO V 4G for some time now, but I can't seem to find one that supports what I have. I am running hboot 1.57 with S-ON (I once tried getting S-OFF and bricked my phone for nearly a day-spent 7 hours trying to fix it-never doing S-OFF again!). I'm currently running the epic NegaLite Blue ROM. Any suggestions?
AFAIK, you must get s off first.
Your best bet for jb look for s on, is to install a launcher, or flash a senseless rom
Sent from my Evo V 4G using xda app-developers app
Without s-off you can't flash JB rom. You have to do s-off first. That's because you need new kernel, you can't change your kernel with s-on.
UndercoVg said:
Without s-off you can't flash JB rom. You have to do s-off first. That's because you need new kernel, you can't change your kernel with s-on.
Click to expand...
Click to collapse
I've changed my kernel multiple times with that one kernel flasher app for the EVO
Yes, it's possible with this app or maybe fastboot (im not sure), but impossible in your recovery.
duscdragon said:
I have been looking for a JB ROM for my HTC EVO V 4G for some time now, but I can't seem to find one that supports what I have. I am running hboot 1.57 with S-ON (I once tried getting S-OFF and bricked my phone for nearly a day-spent 7 hours trying to fix it-never doing S-OFF again!). I'm currently running the epic NegaLite Blue ROM. Any suggestions?
Click to expand...
Click to collapse
You need to downgrade your h-boot to 1.4x.xx. I order to downgrade you need to be s-off
Sent from Mwakious powered EVO 3D
you don't have to go that low, I'm running dirty unicorns (really good rom that I recommend you flash) on hboot 1.50
Sent from my PG86100 using Tapatalk 4 Beta
johnnyboi1994 said:
you don't have to go that low, I'm running dirty unicorns (really good rom that I recommend you flash) on hboot 1.50
Sent from my PG86100 using Tapatalk 4 Beta
Click to expand...
Click to collapse
But he must downgrade anyway. So the best thing to do is flash 1.49.0007 h-boot because it's known for making no problems whatsoever
Sent from Mwakious powered EVO 3D
donkeykong1 said:
But he must downgrade anyway. So the best thing to do is flash 1.49.0007 h-boot because it's known for making no problems whatsoever
Sent from Mwakious powered EVO 3D
Click to expand...
Click to collapse
What is a better way of getting S-OFF Revolutinoary or JBear?
duscdragon said:
What is a better way of getting S-OFF Revolutinoary or JBear?
Click to expand...
Click to collapse
For me it's Revolutionary just because wires and small electronic components just don't go together in my world. But that's just me, a lot of people say that Jbear is easy and simple
Sent from Mwakious powered EVO 3D
like one of the other users said, you should go "S-OFF" first
At that point, you are free to try any hboot, rom, radios, etc.
As for me, ive tried Negolite, SmoothCriminal, PacMAN, and now Wild For The Night.
The Jelly Bean Roms (PacMAN and Wild For The Night) have by far been the ones i like best. I could not get MMS working on PacMAN so i went to WFTN and i got every feature of the phone working perfect (except for 3D which doesnt work on any JB rom at this time)
The rom really depends on what fits ur lifestyle and ur taste. i like the smooth look of a JB rom and the features of the camera.
donkeykong1 said:
For me it's Revolutionary just because wires and small electronic components just don't go together in my world. But that's just me, a lot of people say that Jbear is easy and simple
Sent from Mwakious powered EVO 3D
Click to expand...
Click to collapse
\
I have hboot 1.57 and the beta key for Revolutionary is only for 1.4 and 1.3. Can I still get S-OFF with those?
Will controlbear work with mwakious ? They say it will not but I am not sure.

Categories

Resources