[Q] Samsung Galaxy S III I9300 cracked - Galaxy S III Q&A, Help & Troubleshooting

I had a carabiner case, which was attached to my bag, so the phone was hanging off of my bag. I put my bag down in the car, and closed the door...on the phone. The phone has a nice, tiny crack at the top left of the screen, rendering the touchscreen portion from working. At the time of the incident, the screen was still working, but after 3 days, the screen started to "die off". Now, the screen is not working, as in not turning on, but everything else is still good (I think...the sound's working, the phone's turning on as if there is no problem). I'm living in Belgium and I've called Samsung Belgium, but they weren't much help. Checked the store that I bought it from, but they weren't much help either. I've decided that I'm gonna just replace the screen myself. I've looked online for a similar issue, but I've found nothing. My question is, what do I need to get to begin repairing my phone.
I'll post pictures of the phone later.

You need an display panel and digitizer (they come as one unit. I've seen them on eBay here for £119 for the entire screen assembly and (in this case white) outer frame. It's a very easy job to take apart the S3 and attach such a unit to the motherboard as the S3 is not a complicated assembly at all.
Sent from my GT-I9300

How to replace screen posts/guide on here .
jje

leoni1980 said:
You need an display panel and digitizer (they come as one unit. I've seen them on eBay here for £119 for the entire screen assembly and (in this case white) outer frame. It's a very easy job to take apart the S3 and attach such a unit to the motherboard as the S3 is not a complicated assembly at all.
Sent from my GT-I9300
Click to expand...
Click to collapse
Thanks...another question, what kind of protection you got on your phone?

There's an iFixit teardown on YouTube. Just watch that. Basically though, you take the battery/SIM/Micro SD out, remove the screws at the back to take the rear panel off and expose the motherboard. There's one more screw as I recall, a few ribbon connectors, an aerial clip, a protector over upper portion of the unit which just pulls away and you then remove this and the motherboard and you have an exposed unit (the same unit you buy ready assembled from a number of outlets. As I said, the cheapest I've seen one is for £119 from a seller on eBay which I believe was refurbished.
Sent from my GT-I9300
---------- Post added at 10:15 AM ---------- Previous post was at 10:12 AM ----------
steve1o said:
Thanks...another question, what kind of protection you got on your phone?
Click to expand...
Click to collapse
I use a TPU case and a pretty bog standard screen protector. After my girlfriend broke her screen completely (to the point of not even switching on) from a drop of less than two feet and a friend of mine had the same happen I'm massively paranoid about my S3 breaking and am even contemplating selling it for that reason, though it is reassuring to know I can fix it easily enough I suppose.
Sent from my GT-I9300

leoni1980 said:
There's an iFixit teardown on YouTube. Just watch that. Basically though, you take the battery/SIM/Micro SD out, remove the screws at the back to take the rear panel off and expose the motherboard. There's one more screw as I recall, a few ribbon connectors, an aerial clip, a protector over upper portion of the unit which just pulls away and you then remove this and the motherboard and you have an exposed unit (the same unit you buy ready assembled from a number of outlets. As I said, the cheapest I've seen one is for £119 from a seller on eBay which I believe was refurbished.
Sent from my GT-I9300
---------- Post added at 10:15 AM ---------- Previous post was at 10:12 AM ----------
I use a TPU case and a pretty bog standard screen protector. After my girlfriend broke her screen completely (to the point of not even switching on) from a drop of less than two feet and a friend of mine had the same happen I'm massively paranoid about my S3 breaking and am even contemplating selling it for that reason, though it is reassuring to know I can fix it easily enough I suppose.
Sent from my GT-I9300
Click to expand...
Click to collapse
So, an update. I've had a screen protector the entire time. It didn't occur to me to check the crack. Turns out the crack is inside the glass, which means that the screen is not cracked. Does this change anything?

steve1o said:
So, an update. I've had a screen protector the entire time. It didn't occur to me to check the crack. Turns out the crack is inside the glass, which means that the screen is not cracked. Does this change anything?
Click to expand...
Click to collapse
Not really screen and digitizer are bonded together, with the right tools you might separate them but how are you going to bond the new digitizer to the old screen?
Sent from my GT-I9300 using Tapatalk 2

ghostofcain said:
Not really screen and digitizer are bonded together, with the right tools you might separate them but how are you going to bond the new digitizer to the old screen?
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
I just bought a new screen digitizer thingie, so it's on it's way right meow.

Related

Some help for a newbie... [broken screen]

First of I would like to say thanks to this forum.
I try not to post any problems that have already been answered and this forum was a big help in getting my xda unlocked.
However I had only had my phone in working condition for 2 weeks, enough time to start to like it, when it fell and cracked.
I ordered a new glass screen (no bleeding ink) and had it overnighted. I sucessfully swapped out the broken scree, but in the process I screwed up the phone. So here is whats going on with it, if anyone can help me out it would be awesome.
When taking it apart I accidently broke 2 of the connectors for the ribbon cables on the back of the pcb. Now the phone wont turn on. The screen comes up but its just white and I cant tell if the os is loading.
Sorry for the long winded post
Thanks for the help
Chris
Also if this cant be fixed whats my best option, selling it broken or parting it out? How much could i get?
Re: Some help for a newbie... [borken screen]
beggy said:
When taking it apart I accidently broke 2 of the connectors for the ribbon cables on the back of the pcb. Now the phone wont turn on. The screen comes up but its just white and I cant tell if the os is loading.
Click to expand...
Click to collapse
Well, I guess it depends on how broken the connectors are, but this definitely doesn't sound good...
If you post a few close-up pictures, I'll tell you if there's any hope for fixing it.
Well..
One of those 3 connectors lead to the screen.
My wild guess would be that it's not porperly connected since it's borken.
In that case, I would have done one of two things:
1. Buy a connector through an electronics component vendor, then ,manually replace the broken one or have a electronics lab do it for me.
2. Solder the wires to the connector's base manually (or in a lab) to over-ride it. (I hope you understand what I mean).
At any case, my guess would be a broken connection somewhere in the connectors (one of the 3). This can probably be fixed that way or another.
BTW - I have a lot of dust between the glass and the screen. How do you remove the glass from the screen (it seems to be attached firmly somehow)??
To take the glass apart from the lcd, there are 4 metal tabs (2 at the top and 2 on the bottom) you can pry a thin flat-head screwdriver between the metal tabs (you will see what I am talking about, when you look closer). It will sound bad but its just the glue coming apart.
I tried to get the connectors but had no luck finding a match.
So I am going to part out the phone.
Ill be posting the ebay auctions for the lcd screen, the new glass piece, the motherboard, the battery/case and whatever misc accesories I have lying around.
Before I put all the parts on ebay, I figured I would give the people on here a crack at it. I will entertain all reasonable offers. Send me a PM.
Here is what I have for sale
Case in good condition w/ battery
Motherboard - in good condition just missing the two plastic pieces where the lcd connects.
Brand new glass touchscreen/digitizer
Lcd Screen
Also for sale the in-wall charger, the sync cradle with an extra 3 stylus (styli?).

[Q] Guide on Replacing the Digitizer

Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
keithgrobertson said:
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
Click to expand...
Click to collapse
Try this http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/1
Or, this http://www.youtube.com/watch?v=TbR56jSplRs
Broke my digitizer and did the job myself using the youtube guide above. Just used straight up superglue to glue digitizer to frame. I put a bunch on the top and bottom and very little on the sides.
Amazingly the phone worked when i put it back together... for a while until I screwed up one of the ribbons by opening it a bunch more times. Be extra careful with these, especially the volume/camera ribbon. You can bend it pretty easily trying to slide it back into its slot.
Good luck.
NB: Theres places that will do it for as little as $90 in case you don't want to take the risk.
http://www.ubreakifix.com/
Thanks for posting the youtube link. I can't even quote the post because it involves an external link. The video was vague on details and the quality is crap but it did the trick.
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from amazon and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Metacat said:
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from ebay and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Click to expand...
Click to collapse
I replaced my digitizer, and had the EXACT same thing happen (not the light sensor but the line in the screen that doesnt respond to touch).
Get a new digitizer, but get it from someone else.
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Metacat said:
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Click to expand...
Click to collapse
No. I sold it and let someone else deal with it. Didn't have the time to replace the digitizer again. Too much of a hassle.
I just replaced a digitizer on an atrix... i didnt put any adhesive on it because there was what i thought was adhesive strips on the digitizer... but there's strips on the screen that doesnt respond, i heated it n tried reattaching the digitizer a few times n sometimes the home and back button will work, sometimes they wont... any suggestions? could the lack of adhesive cause this?
Menu buttons problem
if menu buttons is freeze till I block and then unblock my phone is it digitizer problem ?
what do you mean by " block/unblock" ?
Sent from my HTC Desire CDMA using XDA
He means lock/unlock.
Go the ifixit route!
Just went through 3 digitizers in my repair, and wanted to share my experience/caveats
I bought one digitizer from All4Cellular for $25, and the others with a 20% discount a few days later, for $20.
I installed
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Got the idea to move the LCD screen from another RepairUniverse YouTube video and a previous post here, and tried installing the digitizer from the front face of the phone. It was still a delicate matter to bend the flex cable so that it fit through the slot, and then re-position the LCD and align the sticky strips of the digitizer on the LCD and casing. Part of the digitizer worked this time - a 1cm vertical strip on the left fowled any attempt to touch icons or use a keyboard, so I thought I had damaged things again (doh!).
Hoping third time was the charm, I completely disassembled the phone using the guide in the 'ifixit' link, since a digitizer/case assembly was suggested in another thread. The rear camera just needs to be raised above the casing so the thin plate can move upward, and the LCD pops out easily if the sides of the casing are delicately pulled. The digitizer can be positioned easily and with minimal bending/twisting of the flex cables.
When reconnecting everything the third time, I noticed that pressing down on the front camera / digitizer connection *with the rubber boot in place* didn't pass when pulling the connected assembly upward. So I pulled the rubber boot out of the way and snapped the camera / digitizer connection firmly, then re-inserted the boot. A loose connection might have been the culprit for the nonfunctioning part of the digitizer in the second test.
@MrSaba - I had the same issue with capacitive buttons - perhaps because the screen senses touch and disables those buttons. Replacing the digitizer solved the issue
trouble
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
drZeT said:
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
Click to expand...
Click to collapse
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
jjwatmyself said:
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
Click to expand...
Click to collapse
The first one was with the red stripe indeed, from china. The one with a frame came from UK, "used but tested OK". original screen is gone - tore off flex cable while removing.
Well, update...
2 screens bought on eBay were BAD. Had to wait full month for authorised motorola service to change the digitizer. Must say though that both merchants on ebay refunded, no questions asked. Lessons learned - pay more, wait longer, never give up
DrJCFitz said:
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Click to expand...
Click to collapse
What I noticed on their video was that their folded digitizer connector magically unseats itself during the disassembly transition. I had to pry mine off based purely on guesswork and think I might have broken the flip-chip that is stuck onto the frame with double-sided tape. Like yours, my touchscreen doesn't respond at all, despite there being no cable tears. I'm going to try and re-heat that flip chip and maybe get the connections to work again (doubtful).
To anyone else out there attempting this... when you go to remove the touchscreen, HEAT THE CONNECTOR so that you can gently pry it out!
Bad screen I got 3 before it worked its fine now if old one partially works new one doesn't screen is junk took mine apart several times to figure out screens were junk...guess they felt sorry for me give me my money back plus free working screen.from amazon
Also that lock clamp u mentioned first video I watched didn't show unlocking that I just pulled it out and pushed back in it was the 2 screen that I figured out it needed to be pryed loose by the white clamp but guess I didn't damage it..
Sent from my HTC One X+ using xda premium
I have just put in my second digitiser. The first was one had a red stripe, which was junk, the second on I bought had the plastic round the edge and the digitiser.
I put it in and it worked fine no dead spots at all. Then 12 hours in it started to stop working intermittently. Then 24 hours after that while on charge its dead again. I reflashed notattrix and still nothing. I've confirmed all the ribbon connectors are firmly in place and everything looks right.
Any ideas whats wrong?
thanks
Jonnym

[Q] Where to get replacement glass?

My phone was dropped earlier however only the glass is cracked, not the actual screen. Everywhere I look, they only sell them as a pair, but I remember awhile back seeing just the glass for a reasonable price.
Where can I get it now?
Thanks!
Here's a glass replacement for $12.80 (Free Shipping)... CLICK HERE
Instructional Video:
Note: This video uses a Fascinate, but the steps taken should be similar to replacing the Vibrant's screen.
Thanks so much!
No problem. Hope you get your phone back up & running.
How come people charge like $100 to replace...?
Sent from my SGH-T959 using xda premium
VeryCoolAlan said:
How come people charge like $100 to replace...?
Sent from my SGH-T959 using xda premium
Click to expand...
Click to collapse
Because that 'replacement glass' is a scam not a digitizer. It will not fit properly and will not function as a digitizer. If you look at the video, the removed digitizer has some wires on it. That allows communication w/ the motherboard. That glass is just glass. Even if you could remove the broken touch panel (digitizer) and fit the glass to the phone you would have no ability to use it.
The digitizers for all amoled Galaxy S phones are not available without the attached display panel. The replacement screen costs $95 just for the part, then add the labor and that is why it is so expensive.
If you notice, even the people who made the video (while showing the removal) don't sell the digitizer alone. Pro shops replace the whole assembly. If you can get the job done for $100 including labor, take it. It's a great price.
ChauncyG said:
Because that 'replacement glass' is a scam not a digitizer. It will not fit properly and will not function as a digitizer. If you look at the video, the removed digitizer has some wires on it. That allows communication w/ the motherboard. That glass is just glass. Even if you could remove the broken touch panel (digitizer) and fit the glass to the phone you would have no ability to use it.
The digitizers for all amoled Galaxy S phones are not available without the attached display panel. The replacement screen costs $95 just for the part, then add the labor and that is why it is so expensive.
If you notice, even the people who made the video (while showing the removal) don't sell the digitizer alone. Pro shops replace the whole assembly. If you can get the job done for $100 including labor, take it. It's a great price.
Click to expand...
Click to collapse
I just need the glass.
I've seen some other videos and I got it down. All you do is take the glass and remove it from the amoled screen then replace. I don't need a digitizer.
Sent from my SGH-T959 using xda premium
So wait, you can't just replace the glass? In the video they remove the glass from the digitizer. Right?
Sent from my SGH-T959 (Samsung Vibrant)
N00B_IN_N33D said:
Wow, I had no idea. I've never taken apart my phone before, but when I came across the glass replacement on Ebay it looked very legit. 99.4% positive feedback, 34 sold, and 7 day money back... But I guess looks can be deceiving. I figured the wire was hidden from view in the picture. I apologize for posting a link to a scam...
Sent from my SGH-T959 (Samsung Vibrant)
Click to expand...
Click to collapse
Not a problem. Unless you have done any repair work on these things you would not know. Most non oled display phones have the ability to replace touch screen and lcd displays individually. Unfortunately, not ours.
This scam works because most people that buy the glass never really get around to installing it, or if they do and it does not work they think they did something wrong. I have repaired a bunch of these things even if you could remove the digitizer sucessfully as shown in the DirectFix video, you can't get a replacement part. Also, this operation needs to be done in a clean room. Any dust on the amoled panel will bruise it when paired with the touch panel so a successful repair is very unlikely outside of the factory. That is why the repair parts are sold together as a unit.
N00B_IN_N33D said:
So wait, you can't just replace the glass? In the video they remove the glass from the digitizer. Right?
Sent from my SGH-T959 (Samsung Vibrant)
Click to expand...
Click to collapse
Yea that's what I saw....
And yes just the glass...since I'm gonna be with this phone for a few more months I need to replace and this is really cheap!
Sent from my SGH-T959 using xda premium
VeryCoolAlan said:
Yea that's what I saw....
And yes just the glass...since I'm gonna be with this phone for a few more months I need to replace and this is really cheap!
Sent from my SGH-T959 using xda premium
Click to expand...
Click to collapse
You can't 'just replace the glass'. The digitizer and front glass are one and the same. They are inseparable.
---------- Post added at 12:55 AM ---------- Previous post was at 12:53 AM ----------
N00B_IN_N33D said:
So wait, you can't just replace the glass? In the video they remove the glass from the digitizer. Right?
Sent from my SGH-T959 (Samsung Vibrant)
Click to expand...
Click to collapse
What you saw was the digitizer/glass being removed from the AMOLED panel. So, as stated before, no, you can't just replace the glass.
FML. -_-
Sent from my SGH-T959 using xda premium
Call me crazy but if people are buying these and not complaining they don't work. Then either they don't want to look stupid by saying they got scammed or they did replace the glass and is possible. I say it's possible but very hard since the thickness is about that of a piece of paper. I saw this on wiki for the superamoled little confusing.
Super Active-Matrix Organic Light-Emitting Diode or Super AMOLED is a display technology (variant from AMOLED) mainly for use in mobile devices such as mobile phones (see the list below for examples). One of the main differences from other display technologies is that the layer that detects touch is integrated into the screen rather than being overlaid on top.
Click to expand...
Click to collapse
Anyone? Is that saying the display (lcd screen) has the digitizer built in the screen itself?
Mandown said:
Call me crazy but if people are buying these and not complaining they don't work. Then either they don't want to look stupid by saying they got scammed or they did replace the glass and is possible. I say it's possible but very hard since the thickness is about that of a piece of paper. I saw this on wiki for the superamoled little confusing.
Anyone? Is that saying the display (lcd screen) has the digitizer built in the screen itself?
Click to expand...
Click to collapse
They are integral but can be separated.... just not rejoined and still work. Notice that the places that show the removal videos DO NOT sell a replacement part, just the entire screen. Most of the glass that is sold as a replacement is purchased from overseas. It costs more to return it than what was spent to purchase it. They are ALL worthless. If there are not wires coming from it it can't be a digitizer. If you remove your broken digitizer and are lucky enough not to destroy you amoled panel you still have nothing to replace it with. Most if not all people who buy these things never get around to attempting the replacement, or if they do, they destroy the panel in the process so they never get the chance see that the glass does not work. They think they screwed it up instead of being ripped off. That's why you don't see negative feedback about those things.... It's the perfect (almost) scam.
If you want to replace your glass buy the entire assembly ($95.00) on eBay and at the end of the process you will have a great phone again instead of a pile of junk.... not to mention feeling like you screwed up your phone.
Well what I'm going to do is wait for my brother to go to Verizon then take his vibrant and use his screen and mess with mine. Though I need to buff out the scratches. If by some miracle I do make it work I will post here. I hate when people find a way to fix something that some of us are trying to figure out and never report back how or just say "I fixed it was simple." WTF WAS IT! had to deal with that with my plasma which I finally did find one thread and fix it.
Sent from my Vibrant using xda premium, running ICS Passion v10.6 OH YEAH!
Digitizer and glass are factory glued together under high temperatures impossible to separate.
Just buy the whole assembly for $90 ( i've seen them for $79 once) with free shipping and tools on ebay. I always send offers using ebay "ask a question" and sometimes they give me few $$ off. Then it is a piece of cake since you can brake off the glass and remove the whole assembly that way.
My personal Vibrant is made of all kinds of used Vibrants and screen assembly comes from Galaxy S 4G which is good replacement too if you also want to get front facing camera.
technically can be done
while i don't recommend anyone else try, I was able to separate the glass from the screen. the glass was cracked but the screen still worked so i bought just the glass thinking it would be an easy replacement. so when i came to find them glued together i used my hot-air gun to melt the glue and remove to broken pieces of glass one by one, very carefully. when putting it back together with the new glass i couldn't re-glue it but the back tray holds the screen in place well enough. there was only one side effect that i have noticed so far. the glass is a little loose since not held to the screen, and i did burn the screen a little bit with the heat gun and it now has minor discoloration. but it is possible with enough patience and a steady hand.
afx420 said:
while i don't recommend anyone else try, I was able to separate the glass from the screen. the glass was cracked but the screen still worked so i bought just the glass thinking it would be an easy replacement. so when i came to find them glued together i used my hot-air gun to melt the glue and remove to broken pieces of glass one by one, very carefully. when putting it back together with the new glass i couldn't re-glue it but the back tray holds the screen in place well enough. there was only one side effect that i have noticed so far. the glass is a little loose since not held to the screen, and i did burn the screen a little bit with the heat gun and it now has minor discoloration. but it is possible with enough patience and a steady hand.
Click to expand...
Click to collapse
Any follow up on this?
Any video/help for broken galaxy s1 i9000 glass?.
I meam the front thing as i understand its just a piece of glass and not a touchscreen. But for the phone you talk about its a touchscren and not just a glass

replacement screen?

Can i replace the screen of my sprint s3 with a gsm s3 ?
Wrong forum and no.
Sent from my GT-I9300 using xda app-developers app
Jack Barrett said:
Wrong forum and no.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
thank
Jack Barrett said:
Wrong forum and no.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Why is it wrong forum and why no? I guess it's right forum but wrong section though (a question should be posted in q&a). In my opinion the screens may be replaceable as they are dimensionally the same. If I'm wrong then please direct me to a source of your information.
The real question is that why would you want to do that?
Sent from my GT-I9300 using Tapatalk 2
Maybe his is smashed like mine was today. Luckily I found a place that had screens for blue s3 and managed to get there before they closed. As far as I know, they use the same screen for the lte variants available here.
Sent from my GT-I9300 using xda premium
ceo.mtcl said:
Why is it wrong forum and why no? I guess it's right forum but wrong section though (a question should be posted in q&a). In my opinion the screens may be replaceable as they are dimensionally the same. If I'm wrong then please direct me to a source of your information.
The real question is that why would you want to do that?
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
Because he owns sprint device and there is special forum dedicated to it. And because everything is connected to the screen inside. Another reason his device contains different hardware. Happy?
Sent from my GT-I9300 using xda app-developers app
Wow you sure I didn't hit a nerve !
Sent from my SPH-L710 using Tapatalk 2
I'm a technician at a major repair facility that does mostly work on Samsung and Apple products. Ironic right?
I've replaced a few Galaxy S3 screens lately.
The answer is YES, all Galaxy S3 front glass digitizer and lcd assemblies are interchangeable between all US carriers and international versions.
They are all the same international GT-I9300 part number, I opened up a Verizon GS3 today and part of the flex cable that goes to bottom two capacitive touch sensors even say GT-I9300 on it.
Thanks so much that the answer I needed
Sent from my SPH-L710 using Tapatalk 2
Oh and one more thing to add. Do not get fooled into buying those "glass only" front panel replacement kits on ebay for $20-$30. You'll just end up with a nice conversation piece on how you got scammed out of $20-30. I do not even know why they sell those for, they even include these cheap ass tools making it look more legit, like there is somehow a way to actually replace it. It's a full on scam if you ask me. I feel sorry for the poor saps who pick up broken glass S3's on ebay for $350-400 thinking it will only cost them $30 bucks to replace the screen and they'll have a like new S3. Suckers....
It is 100 percent impossible to replace just the front glass panel on the Galaxy S3. The glass panel is fused entirely to the LCD, and the whole LCD is glued to the frame. There is no way to "separate" the glass from the LCD without destroying both.
Bottom line, you need to purchase the LCD and Glass Digitizer as a complete assembly, around $200. To make life easier, you should buy it with the frame also, around $220-240 so you won't have to curse and ***** when you try to pull your old LCD and digitzer from your old frame,broken piece by piece.
Dan37tz said:
I'm a technician at a major repair facility that does mostly work on Samsung and Apple products. Ironic right?
I've replaced a few Galaxy S3 screens lately.
The answer is YES, all Galaxy S3 front glass digitizer and lcd assemblies are interchangeable between all US carriers and international versions.
They are all the same international GT-I9300 part number, I opened up a Verizon GS3 today and part of the flex cable that goes to bottom two capacitive touch sensors even say GT-I9300 on it.
Click to expand...
Click to collapse
Verizon is not Sprint. Open up a sprint device and lets talk again.
Sent from my GT-I9300 using xda app-developers app
Jack Barrett said:
Verizon is not Sprint. Open up a sprint device and lets talk again.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Just checked the technician guide for the Sprint version.
Screen is AMS480GY01. So it's the exact same one as the GT-I9300 and any other US carrier (TMO,ATT,Verizon).
LIKE I SAID BEFORE.....All GS3's Screens/LCDs are interchangeable between all versions of the GS3.
Out of curiosity, what makes you think the Sprint version is so different than any other S3 version which would warrant a completely different screen/samoled assembly?
It's obvious you have never repaired the screen on a Galaxy S3 yet you're challenging a senior level technician who repair these things everyday @ a logic board component level. Our repair levels go way deeper into these units, way beyond what Samsung authorized warranty service centers even have capabilities to do.
Yes. You can seperate and change just the glass.
It is 100% possible and in fact not all that difficult to replace just the gorilla glass on the GS3. I have done it three times. If you heat the glass and pry it up with a feeler guage, it will begin to seperate. Once you get it going it will come off quite easily and leave the LCD behind. Here is the toughest part. Now you need to get the LCD/digitizer portion off the frame without snapping it. Turn the frame to the pack and heat it with a heat gun. Now get a long feeler guage under one corner and push it straight to the bottom. Be careful not to go too far and damage the bottom/ribbon portion of the LCD. Now just continue that process across the back of the LCD like a slim jim till its free. Now all you need is a gorilla glass with adhesive. Any reputable parts supplier can get them on request and they come with the "Optically Clear" adhesive already applied. Just spray a generous application of alcohol on the front of the cleaned LCD/Digitizer panel, peal the paper cover off the back side of the glass and carefully apply it to the LCD. You have about 10 seconds to play and align the LCD with all the alcohol on it before it will start to get sticky.
Dan37tz said:
Oh and one more thing to add. Do not get fooled into buying those "glass only" front panel replacement kits on ebay for $20-$30. You'll just end up with a nice conversation piece on how you got scammed out of $20-30. I do not even know why they sell those for, they even include these cheap ass tools making it look more legit, like there is somehow a way to actually replace it. It's a full on scam if you ask me. I feel sorry for the poor saps who pick up broken glass S3's on ebay for $350-400 thinking it will only cost them $30 bucks to replace the screen and they'll have a like new S3. Suckers....
It is 100 percent impossible to replace just the front glass panel on the Galaxy S3. The glass panel is fused entirely to the LCD, and the whole LCD is glued to the frame. There is no way to "separate" the glass from the LCD without destroying both.
Bottom line, you need to purchase the LCD and Glass Digitizer as a complete assembly, around $200. To make life easier, you should buy it with the frame also, around $220-240 so you won't have to curse and ***** when you try to pull your old LCD and digitzer from your old frame,broken piece by piece.
Click to expand...
Click to collapse
Dan37tz said:
I'm a technician at a major repair facility that does mostly work on Samsung and Apple products. Ironic right?
I've replaced a few Galaxy S3 screens lately.
The answer is YES, all Galaxy S3 front glass digitizer and lcd assemblies are interchangeable between all US carriers and international versions.
They are all the same international GT-I9300 part number, I opened up a Verizon GS3 today and part of the flex cable that goes to bottom two capacitive touch sensors even say GT-I9300 on it.
Click to expand...
Click to collapse
Does this include the screen that cones with the bezel or just the screen and digitizer by itself? Also, do you know if you can change the backing of the sprint lcd/bezel and replace it with a gsm backing (the one that has the sim card opening)? Thanks for your time.
Dan37tz said:
Just checked the technician guide for the Sprint version.
Screen is AMS480GY01. So it's the exact same one as the GT-I9300 and any other US carrier (TMO,ATT,Verizon).
LIKE I SAID BEFORE.....All GS3's Screens/LCDs are interchangeable between all versions of the GS3.
Out of curiosity, what makes you think the Sprint version is so different than any other S3 version which would warrant a completely different screen/samoled assembly?
It's obvious you have never repaired the screen on a Galaxy S3 yet you're challenging a senior level technician who repair these things everyday @ a logic board component level. Our repair levels go way deeper into these units, way beyond what Samsung authorized warranty service centers even have capabilities to do.
Click to expand...
Click to collapse
I recon You wont hear from that fine specimen Jack Parrot again...
What a douch
Verstuurd van mijn GT-I9300 met Tapatalk
In short, unless you ready to use heat gun and separate screen (it is not lcd) from assembly, possibly damaging it or deal with the dust trapped under, or working in dust proof facility, answer is no.
The front frame assembly is 100 percent NOT compatible between international and nam versions due to different chip sets and motherboard which is indented on magnesium frame to sit properly.
Enjoying JKay Deluxe on GT-I9300
flex cable
I need help I wann try this but I heard something about a flex cable and got scared of doing
it can u please help me out I have sprint s3 do I just buy the glass and will other s3 work with this like i9300
Or do I almost need flex cable
phonefreaks said:
It is 100% possible and in fact not all that difficult to replace just the gorilla glass on the GS3. I have done it three times. If you heat the glass and pry it up with a feeler guage, it will begin to seperate. Once you get it going it will come off quite easily and leave the LCD behind. Here is the toughest part. Now you need to get the LCD/digitizer portion off the frame without snapping it. Turn the frame to the pack and heat it with a heat gun. Now get a long feeler guage under one corner and push it straight to the bottom. Be careful not to go too far and damage the bottom/ribbon portion of the LCD. Now just continue that process across the back of the LCD like a slim jim till its free. Now all you need is a gorilla glass with adhesive. Any reputable parts supplier can get them on request and they come with the "Optically Clear" adhesive already applied. Just spray a generous application of alcohol on the front of the cleaned LCD/Digitizer panel, peal the paper cover off the back side of the glass and carefully apply it to the LCD. You have about 10 seconds to play and align the LCD with all the alcohol on it before it will start to get sticky.
Click to expand...
Click to collapse
Dan37tz said:
Oh and one more thing to add. Do not get fooled into buying those "glass only" front panel replacement kits on ebay for $20-$30. You'll just end up with a nice conversation piece on how you got scammed out of $20-30. I do not even know why they sell those for, they even include these cheap ass tools making it look more legit, like there is somehow a way to actually replace it. It's a full on scam if you ask me. I feel sorry for the poor saps who pick up broken glass S3's on ebay for $350-400 thinking it will only cost them $30 bucks to replace the screen and they'll have a like new S3. Suckers....
It is 100 percent impossible to replace just the front glass panel on the Galaxy S3. The glass panel is fused entirely to the LCD, and the whole LCD is glued to the frame. There is no way to "separate" the glass from the LCD without destroying both.
Bottom line, you need to purchase the LCD and Glass Digitizer as a complete assembly, around $200. To make life easier, you should buy it with the frame also, around $220-240 so you won't have to curse and ***** when you try to pull your old LCD and digitzer from your old frame,broken piece by piece.
Click to expand...
Click to collapse
man, I wish I saw this sooner. I did just this and screwed the whole thing up! now I am going to have to pay the big bucks to get it fixed.
any advice on WHERE to send it? someone suggested mobiletechsvideo.com but was wondering if you knew of any other?
thanks.

Samsung galaxy mega glass replacement

Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Oh yea.you have to be extra careful of that flex cable connecting to the lcd which is exposed
Sent from my SCH-I545 using xda app-developers app
warriorpluto said:
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
You can buy the lcd screen + digitizer which comes all pre-assembled and all you have to do it swap the whole screen + digitizer out as one unit..this way no fear of breaking anything..i see one on ebay for $158.00 US for the mega 6.3 i9200..but i think it will also work on the other 6.3 mega models..as they must all be the same that way...but i am not 100% sure on that. :good:
leetrevor81 said:
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
Click to expand...
Click to collapse
If you get the lcd and digitizer together, you can fix yourself and it's easy just as star master says. If you have a shop nearby they can replace just the glass
Sent from my SCH-I545 using xda app-developers app
leetrevor81 said:
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
Click to expand...
Click to collapse
And don't sell. $120 is a freaking rip off
Sent from my SCH-I545 using xda app-developers app
warriorpluto said:
And don't sell. $120 is a freaking rip off
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
How much do you think it would go for on ebay? (or somewhere else) I didn't think a damaged phone would be worth selling?
That phone is still with over $200 as is.just the good motherboard alone. Especially if it had a clean imei number..then counting other parts of the phone too
Sent from my SCH-I545 using xda app-developers app
Good tutorial how to fix it
There is some kind of double side transparent adhesive between LCD and digitizer. So good luck
Opened front glass
Hi, I opened front glass of Mega 5.8 to clean the dust inside it. When I put it back, the touch is not working. Earlier it was working perfectly, I did not remove any cables. Also that I cleaned it with dry cloth while the phone was on.
What may be the issue?
warriorpluto said:
Oh yea.you have to be extra careful of that flex cable connecting to the lcd which is exposed
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
How does it separate?
warriorpluto said:
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
Hi,
I've never worked on one of these before but I have repaired many GS3, GS4, Note 2 with no problems. You successfully repaired one so my question is, is the optical adhesive like the GS3 where it rubs off with your finger? I've noticed a difference in GS3 & GS4 adhesive the GS4 is more difficult to clean off digitizer.
That yellow flex cable in your pic looks like a Digitizer flex. The layers are LCD (bottom) / Digitizer (sits on top of LCD so center) / Glass (top which is what our finger touches).
I have a Mega coming in tomorrow and the customer bought just the glass online. I'll see if I can separate. If you have any questions let me know I have repaired many a phones.
Did you get it?
ReyesARG said:
Hi,
I've never worked on one of these before but I have repaired many GS3, GS4, Note 2 with no problems. You successfully repaired one so my question is, is the optical adhesive like the GS3 where it rubs off with your finger? I've noticed a difference in GS3 & GS4 adhesive the GS4 is more difficult to clean off digitizer.
That yellow flex cable in your pic looks like a Digitizer flex. The layers are LCD (bottom) / Digitizer (sits on top of LCD so center) / Glass (top which is what our finger touches).
I have a Mega coming in tomorrow and the customer bought just the glass online. I'll see if I can separate. If you have any questions let me know I have repaired many a phones.
Click to expand...
Click to collapse
I wonder how was it going with your repair?
http://www.witrigs.com/samsung-galaxy-mega-replacement-parts
Adhesive is a problem
letus1 said:
I wonder how was it going with your repair?
Click to expand...
Click to collapse
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
ReyesARG said:
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
Click to expand...
Click to collapse
If i separated the digitizer and the glass ftom the lcd, than can i bound the new one with LOCA or will that damage the LCD?
ReyesARG said:
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
Click to expand...
Click to collapse
I knew that was the only way to do it, with hot plate and fishing pole string. I'm sure it's a slow process. I'll have to invest in a good hot plate.
Sent from my SM-N900V using xda app-developers app
No huge investment needed, I use a standard electric pancake griddle which can be bought for around $20. Good, even heat. I've never tried the fishing line method but a pair of business cards does the job very well. I get it started with a dull razor blade in the corner and as soon as I see the glass separating, I slide a business card in behind it. Do the same for the other side. On these big screens, slide the cards down a bit, lay it down on heat, repeat. The trick to not busting the LCD is to keep the heat on it and take your time.
My temperature is set to 200 farenheit. Not sure off hand what that converts to in celsius. Ideally, you don't want the surface to pass 120 celsius. If in doubt, start low and increase temp slowly until the glue softens enough.
The glue we're taking about is LOCA[liquid optically clear adhesive] and is UV activated. It can be bought online pretty cheap. If you're going to replace the glass, go ahead and use the LOCA when putting the new glass on. I've seen sensitivity issues on glass that doesn't have the glue between it and the LCD. If you use the glue be sure to remove EVERYTHING from the frame including cameras, speakers, buttons and mics as it can get messy and go pretty much everywhere. To activate the glue you can literally take it outside on a sunny day and it will cure fairly quickly, about 5 mins or so. To remove it from unwanted areas just use a toothpick, toothbrush, and some rubbing alcohol. I've done it dozens of times this way and it always comes out looking factory fresh
VirtueToVice said:
No huge investment needed, I use a standard electric pancake griddle which can be bought for around $20. Good, even heat. I've never tried the fishing line method but a pair of business cards does the job very well. I get it started with a dull razor blade in the corner and as soon as I see the glass separating, I slide a business card in behind it. Do the same for the other side. On these big screens, slide the cards down a bit, lay it down on heat, repeat. The trick to not busting the LCD is to keep the heat on it and take your time.
My temperature is set to 200 farenheit. Not sure off hand what that converts to in celsius. Ideally, you don't want the surface to pass 120 celsius. If in doubt, start low and increase temp slowly until the glue softens enough.
The glue we're taking about is LOCA[liquid optically clear adhesive] and is UV activated. It can be bought online pretty cheap. If you're going to replace the glass, go ahead and use the LOCA when putting the new glass on. I've seen sensitivity issues on glass that doesn't have the glue between it and the LCD. If you use the glue be sure to remove EVERYTHING from the frame including cameras, speakers, buttons and mics as it can get messy and go pretty much everywhere. To activate the glue you can literally take it outside on a sunny day and it will cure fairly quickly, about 5 mins or so. To remove it from unwanted areas just use a toothpick, toothbrush, and some rubbing alcohol. I've done it dozens of times this way and it always comes out looking factory fresh
Click to expand...
Click to collapse
What kind of griddle? This is the one without the edges right?
Sent from my SM-N900V using xda app-developers app
starmaster10 said:
You can buy the lcd screen + digitizer which comes all pre-assembled and all you have to do it swap the whole screen + digitizer out as one unit..this way no fear of breaking anything..i see one on ebay for $158.00 US for the mega 6.3 i9200..but i think it will also work on the other 6.3 mega models..as they must all be the same that way...but i am not 100% sure on that. :good:
Click to expand...
Click to collapse
I like this..
fixxforyou said:
May i ask how much for this glass?
Click to expand...
Click to collapse
Who give your answer ? Mention it..

Categories

Resources