HI,
I have Samsung S3 i tried to upgrade it to the latest firmware via Odin and while it was in processing my laptop froze so i restarted it and now when i get my phone into download mode i get those information:
Product name:
Custom Binary Download: NO
Current Binary: Samsung Official
System Status: Custom
as u can see the product name is "empty"
I really need your help! please...
Thanks
Have you tried to reflash with odin?
Sent from my GT-I9300 using Tapatalk 2
The main thing is you can get into download mode still, like previous post said reflash on a reliable laptop
Reflash with odin. If still problem, remove/replace. battery and Reflash. I think it ll work...
Sent from my GT-I9300 using Tapatalk 2
Thanks alot for your help i will try now and give u the results...
still the same:crying::crying::crying:
this is what i get
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Start odin, put your rom on pda, leave everything unchanged, make sure that repartition button is not enabled, start your phone in download mode, and wait until you see in odin message "added" , than click start. I wish you luck.
Sent from my GT-I9300 using Tapatalk 2
delta1987 said:
still the same:crying::crying::crying:
this is what i get
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Click to expand...
Click to collapse
how you flash with odin?
please see this
http://forum.xda-developers.com/showthread.php?t=1671969
re-partition box should be empty and try changing usb port. do not use usb 3.0 port if you have. good luck.
ok so i tried it with Re-partition checked off and i got this
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLFB_I9300OJVBLF3_I9300XXLFB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I'm a bit of a Noob but here's what I would try - go to sammobile.com and find the latest official ROM for your phone/area. Download it to laptop. Start Odin. Put phone into Download mode then connect it. Click PDA and find the download file and flash it.
The official file should have all you need, but if you did this previous with PIT clicked you will need to ask someone more experienced than me - I haven't had any experience with that.
Another thing you might try is DL Revolution ROM (search for ARHD 9) and follow the Superwipe instructions to get rid of all the previous possible crap. I noticed when I used it there was all kinds of format-type stuff happening as the ROM installed.
If flashing with repartition failed after first try and now your nand is improperly partitioned or not partitioned at all, than you must now thick repartition while flashing by Odin because in other case it will not even start nand write.
But to make it properly you need Rom with separate parts (3 file firmware: PDA, PHONE, CSC) and proper .pit file for mapping new partition structure to flash it.
I can give you a link for such firmware but only for XEO region. If you need another one you must find it yourself.
Rom:
https://hotfile.com/dl/158814567/30ec3bc/GT-I9300_XEO_I9300XXALEF_I9300OXFALEA_I9300XXLEF.rar.html
Proper pit for above firmware:
https://hotfile.com/dl/162097667/e5b3f90/mx.zip.html
Flash with those probably will be successful, but if your nand partition information was erased than there is a risk of data loss on efs partition. But this will be your future problem.
i9.0.1.3k galaxy imperator
I think op need to use a proper pit file along with some stock odin rom to resolve this issue
《spilled from dragon jellybean rom》
And run ODIN as administrator.
My first NAND write failed win W7.
I retried it it worked (but as an Admin)
I still have the same problem even when i run odin as an administrator
still got that pit partition error!!
delta1987 said:
ok so i tried it with Re-partition checked off and i got this
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLFB_I9300OJVBLF3_I9300XXLFB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
you sir have corrupted the PIT mapping...now I believe you will have to flash the 3 file method..get the correct pit file.. I believe mx.pit is the latest...check repartition....
PM SirKunon..he is more experienced in these things..
And never check Repartition again..
Related
Guys
I flashed a ROM from Spain using Odin (I9300XXDLIH, 4.2.1 from Samfirmware) into my S3 (GT-I9300 bought in Brazil) and it works by 1 month. Then my phone starts to crash or boot by itself and finally it stop boot into Samsung screen.
I have access to Download screen, but I have NO access to recovery screen.
Now, I tried to flash a new ROM and Odin says that it has no partition. The phone doesn’t charge anymore (I need to charge using a friend’s phone).
I tried flash an old version (4.0.4) but every time I get “no PIT partition” from Odin. I also tried to flash from different version of Odin and same results.
Is there any way to solve this without getting a Service Center? Here in Brazil is difficult to find JTAG service, so I need some home solution.
Thanks and sorry for my English.
Hi, mines went exactly the same as that last week, tried everything possible software wise. sent it to samsungs ext service centre in scotland. i still dont know fr sure if there goni fix it under warranty as in download mode it says official Rom but it also says custom system. Theyve had it since last tuesday and on the repair status it still says "Acknowledge(ASC)"
heres hoping, and i hope u get urs sorted
Please feel free to find the Sudden Death thread in General section.
spamtrash said:
Please feel free to find the Sudden Death thread in General section.
Click to expand...
Click to collapse
Hi spamtrash,
As I can understand, that thread is to prevent. Now I need to recovery.
I just tried to flash a new ROM again, and I get the following:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBDLJ1_I9300UBDLI2_I9300ZTODLJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the first time I get that. The SetupConnection took a lot of time.
I tried to flash PIT file (do not know if it is the right PIT) and get Fail instant.
Any other help. Thanks to all.
Edit:
Now, I turned off and on again and tried to flash the same ROM:
<OSM> I9300UBDLJ1_I9300UBDLI2_I9300ZTODLJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009>
<ID:0/009> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
It says no PIT partition.
Finally, I tried a PIT:
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009>
<ID:0/009> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
thats mine when i try write PIT file to my phone
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Can't open the serial(COM) port.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
and when i try flash CWM here:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
any suggestion
Anyone flashing a PIT file unless 100% correct is asking for trouble .
Buy a new motherboard .
jje
if theres an error in the emmc flashing the original pit file is unduly. the first thing you need is to flashing recovery to see if its working or not then there solutions such as blocking or disabling the corrupted areas in the emmc chip.
Guys,
Thanks for helping but I guess the phone is briked. I will trie the service center.
Hello, I'd be grateful for some assistance. This morning my s3 was in my pocket and felt really warm. I pulled it out and it was stuck on the boot logo. I'm assuming it had been on that for a while which is why it heated up.
Now, the phone doesn't boot up. I can get into download mode but not recovery.
I did have the Siyah Kernel installed as well as a JB rom.
I have downloaded the latest firmware image for my region UK - (I9300XXEMB5_I9300OXAEMB5_BTU) and tried installing but have had no luck. Below is the message I get. Please help.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I9300XXEMB5_I9300OXAEMB5_996085_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
miahmad said:
Hello, I'd be grateful for some assistance. This morning my s3 was in my pocket and felt really warm. I pulled it out and it was stuck on the boot logo. I'm assuming it had been on that for a while which is why it heated up.
Now, the phone doesn't boot up. I can get into download mode but not recovery.
I did have the Siyah Kernel installed as well as a JB rom.
I have downloaded the latest firmware image for my region UK - (I9300XXEMB5_I9300OXAEMB5_BTU) and tried installing but have had no luck. Below is the message I get. Please help.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I9300XXEMB5_I9300OXAEMB5_996085_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Have you tried with another usb port and are you using stock samsung usb cable?
Your partition structure of the internal storage card is corrupt, the phone is soft bricked. You can usually format and recover if you have backups, particularly of the efs folder.
If you don't then there are a few solutions here on the forum you can try, otherwise it's a Samsung repair.
boomboomer said:
Your partition structure of the internal storage card is corrupt, the phone is soft bricked. You can usually format and recover if you have backups, particularly of the efs folder.
If you don't then there are a few solutions here on the forum you can try, otherwise it's a Samsung repair.
Click to expand...
Click to collapse
Hello, thanks for your reply. I don't have a backup. Would you please point me in the right direction? I'm not sure what I need to do?? where would I get the recovery??(Is that the bootloader?Kernel?Rom?)
Search and read here in Q&A, without a backup of your efs it is less likely to succeed. Otherwise return to Samsung for repair.
boomboomer said:
Search and read here in Q&A, without a backup of your efs it is less likely to succeed. Otherwise return to Samsung for repair.
Click to expand...
Click to collapse
From what I can make out I need to reformat the internal storage. To do this I need the correct pit file. I can't find it on samfirmware.com.
miahmad said:
From what I can make out I need to reformat the internal storage. To do this I need the correct pit file. I can't find it on samfirmware.com.
Click to expand...
Click to collapse
i dont know if this will work ... but try the resurrection rom!
I can't bet into recovery.installing from Odin also gives error.
flash the correct pit file, use search, it's been posted
Glebun said:
flash the correct pit file, use search, it's been posted
Click to expand...
Click to collapse
I have attached the Pit file I have used. No luck. It does nothing, I have left it for ages.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
Service centre then but their is a big queue judged by todays bricked phone posts .
jje
Hi all,
I have a Samsung galaxy S3 GT-I9300. 2 days ago it crashed and won't boot anymore. The reason was can't mount /cache, can't mount system ... on recovery mode. I tried only the wipe cache option and it did nothing.
I started looking at the forum to understand how to fix it. I deciced first to make a backup of my data if possible so I downloaded Odin v3.07 and philz_touch_6.07.9-i9300.tar.md5. I read in another thread that we can manage to copy data from the phone using philz tools.
The problem here is that flashing philz tools with Odin fails all the time. Now I can only access the download mode. At boot, I have a "Firmware upgrade encountered an Issue..." I tried with Kies recovery but it failed too.
In my sdcard, I have no folder clockwordmode ! In download mode
PRODUCT NAME : GT-I9300
CUSTOM BINARY DOWNLOAD : Yes (3)
CURRENT BINARY : Custom
SYSTEM STATUS : Ofiicial
I am bit lost as there seem to be a lot of options in other threads. I don'y know where to start or what to do ? is it the PIT files to restore ? the firmware, the kernel ? the whole OS ?
Many thanks
Don't use pit file. pit is Last resort!!!! Get stock firmware from sammobile.com and flash it through Odin. Forget kies. Read about Odin before flashing.
You'll need to flash with a *.pit file, and the ROM downloaded from sammobile in order to restore your device. Use the *.pit file as the absolute last option to restore your phone. It will repartition your phone, and any power loss of either the machine you are flashing from, or your phone will render it a permanent brick.
Thank you
I am downloading the latest firmware from sammobile (1.1 GB) and Odin 3.09. There are specific instructions for Odin on sammobile website so I don't think i'm goint to mess it up. I will let you know if it did work for me.
I tried to flash the image from sammobile but it failed. There is no log I can read to understand why
Here is the name of image I downloaded I9300XXUGML2_I9300FTMGML2_I9300BVUGML1_HOME.tar
Concerning Odin, its the 3.09 GS3 by l0gan
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGML2_I9300FTMGML2_I9300BVUGML1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Shall I try with an older image (this one is the latest) ? or retry by messing the PIT ?
Nand write fail = motherboard replacement.
Keep trying to flash and don't give up but please leave pit till the end. Yes try three part recovery firmware and older firmware "not ics" SDS on ics firmware and you don't want that. But at the end of the day nand write fail means hardware failure.
Hi again,
I succeeded to flash one image from 2013. Odin says PASS!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXELL1_I9300FTMELL1_I9300BVELK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Removed!!
<ID:0/006> Removed!!
<ID:0/006> Removed!!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
However, I still have the "Firmware upgrade encountered an issue" at boot I removed the phone when I saw the message Removed in Odin. I am not sure whether it didn't let the process finish well or I did right. Any ideas or suggestions ?
I succeeded to reinstall the latest firmware and I got back the samsung logo at boot. However It still doesn't go any further and no recovery mode ... Is there a way to check the status of the system ?
Omg its alive!! Odin said pass! Just keep flashing that firmware till you get recovery and then factory reset.
Try the rescue firmware in general thread, follow the instructions exactly.
Sent from my GT-I9300 using Tapatalk
Hello
An update of my case. After struggling 2 days with NAND write fail and trying lots of firmwares... I succeeded to install CMW recovery tool. From that, I installed Cyanogenmod 10.0.2. I struggled to make it boot too as it looped on cyanogen logo many times.
Now I must confess that I am afraid of rebooting the phone as I thought it was dead :angel:
Hope it helps someone else :highfive:
Great feed back for others. and go's to show never give up flashing with Odin. Odin is a pain in the ....
Congrats :thumbup:
Hello,
i try to install twrp on my s6 edge, but now it will not start anymore, the screen is following the samsung Logo black.
i try to install the original firmware from sammobile, but it stuck or give me an error.
what can i do? i try on 2 computer, 2 usb cable and and and... its the same all time
can you help me pls?
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FAUT1AOCN_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
sure you using latest Odin..? and firmware matches..?
try from odin 1.85 to 3.10 all
What model of s6 edge you haw??Look on samifirmware for yours model.Use odin 3.10.6 i think
and use the right region code BTW branding code..for free Germany it's dbt as example..
I hate to say it, but I have the exact same issue...
I tried to install TWRP, now the screen just goes blank after the Samsung logo.
I have downloaded the latest O2 UK firmware, flashed as normal using odin 3.10.6, and I get a "fail" too
Please could someone suggest something?
Thanks
EDIT: Re-flashed root, and all good again!
Guys i was upgrading official firmware through ODIN, but it failed. Tried flashing TWRP Recovery as well and below error occured. Need help as my S6 Edge 925F is stuck and won't boot. One more thing, i can enter download mode just fine.
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003>
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
PIT related error bothers me .......
@aneeqkhan I know this thread is a bit dated now, but nobody has replied to you question either? I am trying to recover my friends Galaxy S6 Edge SM-G925I, his bricked after a failed standard OTA update. Flashing stock firmware worked for about 1 week then the whole thing crashed and is un-bootable. Attempting to flash the exact same firmware again in hopes that I could boot into recovery (recovery by button combination DOES NOT WORK!) so was hoping to just boot and factory reset (I was thinking that maybe a data corruption was the cause we didn't wipe his phone because he didn't back it up)...upon putting the device into download mode and flashing the exact same firmware package that worked the week before I get the same error that you are getting? Not only that but none of the claimed fixes online for these devices has worked!?
Note: This is a 100% stock device never had anything flashed to it before I got it and still hasn't had anything custom flashed to it either
I am more interested now if you managed to recover your S6 and if so how did you do it?
Suddenly phone freezed and restarted and asked me to reset to remove encryption
then when i tried formatting using TWRP it displays the following
Unable to open '' to wipe crypto key
unable to format to remove encryption
Updating partition details......
Failed to mount '/efs' (Invalid Argument)'
Failed to mount '/cache' (Invalid Argument)'
Failed to mount '/System' (Invalid Argument)'
Failed to mount '/data' (Invalid Argument)'
Failed to mount '/preload' (Invalid Argument)'
...done
unable to mount storage
Push an official cwm recovery via odin. If no joy flash back to stock and start over.
Sent from my HTC One M9 using Tapatalk
please let me know how to push CWM from odin . Can you please assist me here
shivadow said:
Push an official cwm recovery via odin. If no joy flash back to stock and start over.
Sent from my HTC One M9 using Tapatalk
Click to expand...
Click to collapse
This was the result when i tried flashing CWM
<ID:0/015> Added!!
<ID:0/015> Odin engine v(ID:3.1100)..
<ID:0/015> File analysis..
<ID:0/015> SetupConnection..
<ID:0/015> Initialzation..
<ID:0/015> Erase...
<ID:0/015>
<ID:0/015> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
shivadow said:
Push an official cwm recovery via odin. If no joy flash back to stock and start over.
Sent from my HTC One M9 using Tapatalk
Click to expand...
Click to collapse
Flash recovery twrp. 2.8.7.3 via heimdall. Other way flash back to stock rom with i9300 pit file via odin.. make sure you choose the right pit for i9300 16gb or i9300 32gb.
Id blame twrp. I had nothing but issues with it. Flash back to stock and start over. It's now your only option.
There is a chance you've had sds (sudden death syndrome) and the nand could be corrupt. You fix it with a pit file via odin but ONLY as a last resort. Flashing pit files is a final throw before pronouncing it's death.
The stuff i use : https://drive.google.com/folder/d/0B4vTiHTBB629ZW5vQndpbjFnblk/edit
You will NOT find a pit file in there as i don't support pit flashing, because it is final. It either works or it doesn't. You will have to find one yourself if you need one.
Sent from my HTC One M9 using Tapatalk
Help please
Hi guys i Got the International version of Samsung galaxy S3 GT-I9300 and something went really Wrong
So i tried every posible way to Unbrick it With every single ODin every recovery tried a 3 different stock Roms but always failed
In Odin I got this Error
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNJ2_I9300MSTGNJ1_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
And also tried do do a Factory reset Through Recovery and apperantly Failed as well i got the screenshot atached bellow with the errors
So please if everyone have a solution for this particular Issue please any help is welcomed Thanks
emptywordsss said:
Hi guys i Got the International version of Samsung galaxy S3 GT-I9300 and something went really Wrong
So i tried every posible way to Unbrick it With every single ODin every recovery tried a 3 different stock Roms but always failed
In Odin I got this Error
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNJ2_I9300MSTGNJ1_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
And also tried do do a Factory reset Through Recovery and apperantly Failed as well i got the screenshot atached bellow with the errors
So please if everyone have a solution for this particular Issue please any help is welcomed Thanks
Click to expand...
Click to collapse
Format /cache through recovery (philz). Mounts and Storage --> Format /Cache.
shivadow said:
Id blame twrp. I had nothing but issues with it. Flash back to stock and start over. It's now your only option.
There is a chance you've had sds (sudden death syndrome) and the nand could be corrupt. You fix it with a pit file via odin but ONLY as a last resort. Flashing pit files is a final throw before pronouncing it's death.
The stuff i use : https://drive.google.com/folder/d/0B4vTiHTBB629ZW5vQndpbjFnblk/edit
You will NOT find a pit file in there as i don't support pit flashing, because it is final. It either works or it doesn't. You will have to find one yourself if you need one.
Sent from my HTC One M9 using Tapatalk
Click to expand...
Click to collapse
I tried flashing with Odin and Heimdall. All i get at the end is failed. Odin fails at NAND and heimdall runs till 100% for all whatever i choose. Suggest me any procedure on how to check if my internal storage is intact and can be retrieved. So that i can atleast sleep peacefully.
reinzl said:
Flash recovery twrp. 2.8.7.3 via heimdall. Other way flash back to stock rom with i9300 pit file via odin.. make sure you choose the right pit for i9300 16gb or i9300 32gb.
Click to expand...
Click to collapse
This was the result when i tried flashing CWM
<ID:0/015> Added!!
<ID:0/015> Odin engine v(ID:3.1100)..
<ID:0/015> File analysis..
<ID:0/015> SetupConnection..
<ID:0/015> Initialzation..
<ID:0/015> Erase...
<ID:0/015>
<ID:0/015> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
RajeshVV said:
This was the result when i tried flashing CWM
<ID:0/015> Added!!
<ID:0/015> Odin engine v(ID:3.1100)..
<ID:0/015> File analysis..
<ID:0/015> SetupConnection..
<ID:0/015> Initialzation..
<ID:0/015> Erase...
<ID:0/015>
<ID:0/015> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
For 16 GB of GT-I9300 only. Please don't try it to other devices.
Reverting To Stock Partition Table GT-I9300 16GB
Sent from my GT-I9300 using Tapatalk
reinzl said:
For 16 GB of GT-I9300 only. Please don't try it to other devices.
Reverting To Stock Partition Table GT-I9300 16GB
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
Tried flashing PIT and was unsuccessful. Not sure if the data partition is intact and if so how to know its presence and the status of it.
Anyone solve this problem? I'm using N7100 and get this problem too
Tried to flash PIT with new odin version always noti "failed",
with 3.0.7, 3.0.9, odin freeze at "Get PIT for mapping..", I waited more than 30 minutes but nothing happen,
Tried to flash stock ROM but failed at "NAND Write Start!!"
Someone please help me fix this problem.
Are you using the original Samsung USB cable? Tried other USB cables and USB 2.0 ports?
oh, hi audit13,
Of course I used original Samsung USB cable, I changed some other cables, and USB ports(2.0, 3.0) to test, but nothing new.
I think no one can fix this problem, bring to cell store is the best choice
When flashing with Odin, which is the file that fails to flash? Maybe post the Odin log?
audit13 said:
When flashing with Odin, which is the file that fails to flash? Maybe post the Odin log?
Click to expand...
Click to collapse
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Everytime it end with this failed.
If I flash only PIT, It will stop at
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
I waited for 1 hour but nothing change.
There shoot.bin file is not flashing because the memory is damaged, the ROM is not for the phone, the bootloader in the phone is newer than bootloader in the rom, or you need a different USB cable.
audit13 said:
There shoot.bin file is not flashing because the memory is damaged, the ROM is not for the phone, the bootloader in the phone is newer than bootloader in the rom, or you need a different USB cable.
Click to expand...
Click to collapse
"the bootloader in the phone is newer than bootloader in the rom"
Sorry, but how to know bootloader in the phone is newer than bootloader in the rom?
I flashed Roms with Android ver 4.4.4, 6.0.1, 7.1.1, and don't know much about bootloader, can you help me find my bootloader ver and find the way to resolve this problem. Thanks