Today i was using my phone and without any reason, the haptic has stopped to works.. Also if i try to get recovery or download mode, no haptic..
Any tip?
Thanks
Go to Settings -> Sounds and check if Haptic Feedback is off?
Also, check if you are using the Power Saver mode.
If I'm not wrong, by default it turns off the haptic feedback.
eggman89 said:
Go to Settings -> Sounds and check if Haptic Feedback is off?
Also, check if you are using the Power Saver mode.
If I'm not wrong, by default it turns off the haptic feedback.
Click to expand...
Click to collapse
is all on.. the strange thing is that has stopped to works suddenly.. i tried to restore backup but nothing..
also if i try to get in download mode or recovery ( so out of software) it doesn't works..
Does the vibration works in general?
You can check it in settings - > sounds and select any vibration
Sent from my Samsung Galaxy S3
eggman89 said:
Does the vibration works in general?
You can check it in settings - > sounds and select any vibration
Sent from my Samsung Galaxy S3
Click to expand...
Click to collapse
nop, no vibration at all, neither at startup.. it will go in assistance i think
Backup data and factory reset first .
jje
erto90 said:
nop, no vibration at all, neither at startup.. it will go in assistance i think
Click to expand...
Click to collapse
Might be an hardware issue then.
Time to visit the Service center
Sent from my Samsung Galaxy S3
Check if you have the power savings mode enabled. That turns of haptic also.
☞ sent from GS3 or Nexus
Hi!
If doing factory reset still doesn't do the job, then you might as well download a stock firmware and see if that does the job. If not, then I'ma fraid to say that it's a hardware problem.. Send it to the Service Center ASAP!
I hope this helps! Cheers
check your settings, and turn off power saving,
Sent from my GT-I9300 using xda premium
ceo.mtcl said:
Check if you have the power savings mode enabled. That turns of haptic also.
☞ sent from GS3 or Nexus
Click to expand...
Click to collapse
I'm sure sure this is what caused it. Like I've mentioned earlier...
☞ sent from GS3 or Nexus
Related
Hey guys!
In CM7, when I hit the Ace's power button, it ends the call. I don't want this, I want the good old turn-off screen, like on stock roms. I searched everywhere and I didn't found any option to change this.
Can someone point me what can I do?
Thanks!
Setting/call setting and tick on always use proximity
Sent from my GT-S5830 using Tapatalk
Renan Lazarotto said:
Hey guys!
In CM7, when I hit the Ace's power button, it ends the call. I don't want this, I want the good old turn-off screen, like on stock roms. I searched everywhere and I didn't found any option to change this.
Can someone point me what can I do?
Thanks!
Click to expand...
Click to collapse
settings--accessibility---untick the "power button ends call"
cheers
Dragonoid said:
settings--accessibility---untick the "power button ends call"
cheers
Click to expand...
Click to collapse
There is nothing under accessibility, its empty oO
shailpancholi said:
Setting/call setting and tick on always use proximity
Sent from my GT-S5830 using Tapatalk
Click to expand...
Click to collapse
This is useless to me, since I almost never use my phone holding it. I use the earphones that come with it.
Renan Lazarotto said:
There is nothing under accessibility, its empty oO
This is useless to me, since I almost never use my phone holding it. I use the earphones that come with it.
Click to expand...
Click to collapse
no damn it there is an option !!! check my screenshot!!!
which cm7 are u using btw????
I don't think the setting for the power button is in Accessibility on CM, try looking around the CM menu, I think that's where it is.
LolNade said:
I don't think the setting for the power button is in Accessibility on CM, try looking around the CM menu, I think that's where it is.
Click to expand...
Click to collapse
Do u have eyes???? can u see my screenshot????
Edit: after reading your post below it appears that you do have eyes
btw i had cm7 by vo-1 and i think that option was present in accessibility even in his rom( currently i have cm7 by F.A.T )
Dragonoid said:
Do u have eyes???? can u see my screenshot????
Click to expand...
Click to collapse
No, I don't have eyes.
There are a few different variations of CM, and the one I used to have (I think it's the one by vo-1) had that setting in the CM menu.
Even LeWa has it
Sent from Samsung Galaxy Ace
cm7 power button ends call in galaxy ace
I switched over to cm7 on my galaxy ace a week ago. Its very frustrating that the power button ends the call, i always disabled the proximity sensor in stock firmware and kinda used to that.
everytime i try to turn the screen off in a call, it actually ends the call. There is no option in accessibility settings to prevent power button from ending the call (screenshots attached)
I also downloaded an app phone settings manager and that too has no effect.
please help!
Same as here. Using CM7 from vo-1. I think that I'll switch to the one provided by FAT. Can someone confirm if it has that option in Accessibility?
This is what I have. Apart being in portugese, of course.
you can download "Screen Off and Lock" from the Play Store.
this is what I did.
so when someone calls. press the home button to go to your home screen then click the shortcut you have or if not go to your app drawer and press it to turn off your screen.
I'm using go launcher so I set the application to be activated when I glide down my finger in my home screen.
ijustzeke said:
you can download "Screen Off and Lock" from the Play Store.
this is what I did.
so when someone calls. press the home button to go to your home screen then click the shortcut you have or if not go to your app drawer and press it to turn off your screen.
I'm using go launcher so I set the application to be activated when I glide down my finger in my home screen.
Click to expand...
Click to collapse
Nah, too much trouble. I want it more simple, like it was on stock. And it has to be somewhere on the settings, maybe I'm just not finding it.
good luck in finding it.
Sent from my GT-S5830 using XDA
I've used Grif's CM7 and in that ROM, POWER BUTTON ENDS CALL option was in Accessibility only
I don't think that I'll need this anymore. Yesterday I was using the phone when I needed to hang-up the call, and it was right in front of me, so I didn't needed to power-on screen, unlock it and then hang-up. I just hit the power-button and done!
Also, I think that I can live with the screen-delay to power-off.
Renan Lazarotto said:
I don't think that I'll need this anymore. Yesterday I was using the phone when I needed to hang-up the call, and it was right in front of me, so I didn't needed to power-on screen, unlock it and then hang-up. I just hit the power-button and done!
Also, I think that I can live with the screen-delay to power-off.
Click to expand...
Click to collapse
Whoahhh!!!! first you say u want it off and then u say i like it!!!phewwwww
sent from my D®O!D™
Whatsapp vibration pattern
Can anyone tell me if theres an app to increase the intensity of vibration if we get a message on whatsapp? I have to keep my phone on vibration in class and always miss out on the messages as the vibration intensity is too low.
I figured how to change it for gmail and sms through an app but how can i change it for other apps like whatsapp?
Dragonoid said:
Whoahhh!!!! first you say u want it off and then u say i like it!!!phewwwww
sent from my D®O!D™
Click to expand...
Click to collapse
Hahahaha, yeah, 5 mins after I posted this I noticed that this "feature" might be useful
Hi!
I'm using a recent CM9 nightly with default kernel.
I would like to have your opinion : about 3/4 a week my SGS3 is "stuck" when it's locked : impossible to wake up using home or power button, the screen stays black.
The weird thing is that when it happens, the phone is not frozen : I can still hear music on the headphones and control volume using Up/Down buttons.
Sometimes I let it stuck and receive a notification some minutes later and the phone magically can be unlocked again, screen wakes when I push Home button.
Very weird and annoying when that happens.
My question is : what do you think it could be? An app? How can I debug this and know what prevents the screen to wake up when that happens?
Thanks.
Wipe and reflash the rom
zodiaxe66 said:
Wipe and reflash the rom
Click to expand...
Click to collapse
Thanks, but is that the kind of easy answer you all tell when you don't know the exact answer?
When I installed CM9 a week ago, I did do a full wipe...
I think that next time it happens, I will try to connect my SGS3 on USB and do a adb logcat, maybe I'll find useful information.
Have you tinkered with any of the could settings or voltage settings?
Sent from my GT-I9300 using xda premium
ricey1986 said:
Have you tinkered with any of the could settings or voltage settings?
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Nope
slainer68 said:
Nope
Click to expand...
Click to collapse
Having a similar problem to yourself. Installed CM9 rom had a play and then went back to omegaV9 performing a full wipe using the instructions on this site before reflashing.
Since then when my phone is locked screen off then i unlock either via swipe or using security code (digits ) it looks like the phone unlocks but sort of does a warm boot with black screen for a few seconds with the two buttons down the bottom light up.
When it starts it looks like all the apps have stopped and are restarting again.
I re flashed again omega 9 thought i had it sorted but it started playing up again this evening.
If anyone has any ideas please post..
Hi, I'm a newbie here. I also exprience this problem with my samsung GT-i9300. I hoping to see a fix with this problem.
This forum has been so helpful to new android users. Thank you guys.
Hallo XDA Friends,
I have a problem with the LED on my month old s3 ( euro unbranded )
Everything was going great with the LED I Installed Light flow everything was still fine.
I updated to JB official stock rom as i am unrooted, and since then the LED only works when
i boot up the phone and when i use the Test utility ( red green blue ) colours. With lightflow uninstalled
and no LED management software still nothing works. Also not with screen off.
Now I am stuck because it clearly is not a Hardware problem as It works on boot and in test mode,
But not in anny other situation.
I hope someone here can help me and thanks in advance!
check lightflow in the accessibility settings.
if done already to go lightflow settings > uncheck enable lightflow > close app.
open light flow again and enable lightflow.
Sent from my GT-I9300 using xda premium
Still not working
bordikun said:
check lightflow in the accessibility settings.
if done already to go lightflow settings > uncheck enable lightflow > close app.
open light flow again and enable lightflow.
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
I followed your instructions and it is still not working somehow. I also tried
doing the internal Lightflow test ( all LED test ) and nothing happens when i
turn off the screen ?
Got anny other ideas ? am i the only one on this planet with this problem ^^
Thanks
Disignual said:
I followed your instructions and it is still not working somehow. I also tried
doing the internal Lightflow test ( all LED test ) and nothing happens when i
turn off the screen ?
Got anny other ideas ? am i the only one on this planet with this problem ^^
Thanks
Click to expand...
Click to collapse
Hi,
First, download Light Manager on play store, use this app, not include in sammy rom.
If you are rooted, try Siyah Kernel, go to STweak, Misc > Notification > Fading.
Now, all is okay, no problems
Uncheck Lightflow in rom settings, or a big battery drain will coming...
Sorry for my awful english ^^'
Still not working
Toshiro-Sama said:
Hi,
First, download Light Manager on play store, use this app, not include in sammy rom.
If you are rooted, try Siyah Kernel, go to STweak, Misc > Notification > Fading.
Now, all is okay, no problems
Uncheck Lightflow in rom settings, or a big battery drain will coming...
Sorry for my awful english ^^'
Click to expand...
Click to collapse
I Have tried this also. No luck. I am not rooted. I really just dont understand as the LED works on boot and
in the utility device Test.. Somehow it seems that any other test / usage of the LED doesnt work exept for that..
this should be checked in the settings > display > LED indicator > Notifications
Sent from my GT-I9300 using xda premium
Has been
bordikun said:
this should be check in the settings > display > LED indicator > Notifications
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
It has been the whole time :/
well can't think of any thing else.
but might give it a try. uninstall lightflow and reinstall do not restore from backup
Sent from my GT-I9300 using xda premium
:/
bordikun said:
well can't think of any thing else.
but might give it a try. uninstall lightflow and reinstall do not restore from backup
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
I dont know what to do thank you though Maybe annyone ells can help me!
EDIT - I JUST READ THAT SINCE JELLY BEAN THE LED IS MANAGED BY THE LIGHT SENSOR
MY LIGHT SENSOR ALWAYS SAYS 0 AND CAN NOT ADJUST BRIGHTNESS OF SCREEN DUE TO
WATER DAMAGE.
Is there a way to turn off the Light sensor or enter a value that it "emulates " ?
Still need help
Problem Still persists !
MY LIGHT SENSOR ALWAYS SAYS 0 AND CAN NOT ADJUST BRIGHTNESS OF SCREEN DUE TO
WATER DAMAGE.
Pointless asking then its a hardware repair .
jje
JJEgan said:
MY LIGHT SENSOR ALWAYS SAYS 0 AND CAN NOT ADJUST BRIGHTNESS OF SCREEN DUE TO
WATER DAMAGE.
Pointless asking then its a hardware repair .
jje
Click to expand...
Click to collapse
I dont understand even though the LED is clearly working when i boot and test it ?
Hello...
I have updated my samsung s3 gt-i9300 using OTA from android stock to 4.1.1 android version, i found that the led indicator does not work
Plz..can any one help me...
Plzzzzzzzzzzzz
How?
LED doesn't work at all or it fades?
Did you try rebooting?
Sent from my GT-I9300 using xda premium
excuse my language.
when i reboot the phone, the LED works normally.
but it doesn't work with messages or missed calls or etc..
knowing that all check boxes of the LED indicator are checked (in the LED indicator settings).
ashrafmedlej said:
excuse my language.
when i reboot the phone, the LED works normally.
but it doesn't work with messages or missed calls or etc..
knowing that all check boxes of the LED indicator are checked (in the LED indicator settings).
Click to expand...
Click to collapse
Hey,
if it happens again, type *#0*# and click on LED. It will test your LED, you only have to click on the screen to change the color. After three colours, it is tested. If you can't activate the call LED in settings, try to reset or reflash your phone!
TheRealFelix0212 said:
The best way to reset ya phone is to go in to your Stock Recovery ( Vol. Up + Home Button + Sleep/Wake). There you have to choose "wipe data/factory reset" with "Vol. Down Button". Confirm with the "Sleep/Wake Button". Now you have to confirm that you want to wipe your phone. Use the "Vol. Down Button" again,choose something like "Yes, wipe all
users" and confirm with "Sleep/Wake Button"!
Click to expand...
Click to collapse
ALL DATA WILL BE LOST!! On your internal Storage (sdcard0, not extSDCard) too!!!
I'm not responsible for any damages on your device!
Greetings....
i am really thankful..
but unfortunately
i tested the LED and it work (from *#0*#), andi got the same result (not working with messages and missed calls and etc...).
then i made factory reset from the stock recovery, also i got the same result.
any other solution???
ashrafmedlej said:
i am really thankful..
but unfortunately
i tested the LED and it work (from *#0*#), andi got the same result (not working with messages and missed calls and etc...).
then i made factory reset from the stock recovery, also i got the same result.
any other solution???
Click to expand...
Click to collapse
Did you turn on Blocking Mode or Power saving mode?
Sent from my GT-I9300 using xda premium
no the "Blocking mode" and the "Power saving" are disabled..
note: also the front camera and the vibration are not working in my phone
ashrafmedlej said:
no the "Blocking mode" and the "Power saving" are disabled..
note: also the front camera and the vibration are not working in my phone
Click to expand...
Click to collapse
I think you better download the latest 4.1.2 version and flash it via odin
Sent from my GT-I9300 using xda premium
Should i flash a custom 4.1.2 rom or there is a stock 4.1.2 rom
Look for the Wanam version of XXELKC in the General section....
ashrafmedlej said:
Should i flash a custom 4.1.2 rom or there is a stock 4.1.2 rom
Click to expand...
Click to collapse
Yes there is official stock rom 4.1.2 XXELKC. ...Poland rom
Sent from my GT-I9300 using xda premium
Hey guys.. I've been having some real trouble with my LED Notifications. Let me give you the gist.
- Battery Light = Working
- Notification Light = Worked for about 2 Weeks after I got the C10 mod, hasn't worked since..
I've done all the basic things I could do.. Went through settings, and rebooted.. I really was just hoping for a quick fix and to realize I was just stupid, but I don't think that's the case. Anyone that can help, please give out a shout. Thanks!
Samsung Galaxy S3 i717 (AT&T) - Rooted - C10 Mod
Have you, by any chance, dropped the phone or made it shock abruptly? Because where I live, many around me, including myself, have seen LED capability die entirely on our i9305 and i9300 Samsung devices.
Face it: It's **** hardware. Crappy produce. Non-lasting, profit-based disposable plastic garbage. Ensuring infinite growth on a finite planet. Which is why we will ALL be gone in, say, 2040.
EDIT:I fixed it! turns out it was a hardware problem which occured after i replaced the screen. It was fixed by following instructions on this youtube video,called "How to Fix Proximity Sensor Issue for Samsung Galaxy S3, S4, or Note 2" ( i can't link right now because I'm new, so just look it up on youtube.) so if anyone encounters the same problem hope this video will help!
Hey guys. New to the forum I tried to do a bit of searching but couldn't really find an answer.
So I have two questions/problems I guess.
First off when I go into a call, sometimes the phone screen goes black as soon as I start the call, and won't turn back on until I hang up using the power button. From what I understand it's due to the proximity sensor always being on? But I have not been able to find a solution to this.
Secondly is, I've noticed with the lock screen notifications, when I ticked the option for wakescreen when receiving notifications, and when the screen is off, the proximity sensor is on. and when i untick the wake screen option, it goes off again.
I'm using Fusion-Boeffla Rom latest version as of now, 26-02-14 one. But this problem has been around when I was testing different roms such as temasek unofficial CM.
Any ideas how to fix this?
Thanks in advance!
1- go to calls -> settings -> uncheck turn of screen during calls.
Sent from my GT-I9300 using Tapatalk
amirTor said:
1- go to calls -> settings -> uncheck turn of screen during calls.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
I can't find that setting unfortunately, also is this a hardware problem or software?
Jerryxmas said:
I can't find that setting unfortunately, also is this a hardware problem or software?
Click to expand...
Click to collapse
www.youtube.com/watch?v=z7kx27c1Iao&cd=1&ved=0CDQQtwIwAA&usg=AFQjCNHPZTtRTQj2KfBVwUOb3cUm-UNSkA
And its probably a kernel / rom issue
Sent from my GT-I9300 using Tapatalk
i can't click the link, but i've seen that option in stock samsung roms before, but i can't seem to find it on my rom. And you're right, its very likely its a rom/kernel issue, i may try a different rom or even stock to see if it helps =) thanks