Hello everyone.
I own Motorola Atrix 4g AT&T with 2.3.4 / 4.5.91 Build.
I have read every single thread about Unlocking the bootloader yet I still cannot do it.
First I tried directly the fastboot unlock command for unlocking it but I had an error saying that OEM Unlock is not implemented. Thats OK since the stock bootloader isnt unlockable. So I downloaded RSD Lite as well as the two SBF files (the small pudding and the huge pudding (full version) of AT&T unlockable/pre root) Here is where I got stuck! I have the drivers properly installed and I tried both Windows7 and WindowsXP still i cant get past the boot logo. Here is the situation.
I connect the Phone in RSD Mode. In RSD Lite it shows as NS Flash Olympus and stays connected. When I load the SBF file and press start it gets to 100%. Then phone reboots and RSD Lites says that its waiting for phone to re-enumeration and after a while it gets the error message: Phone[0000]: Phone did not re-enumerate after RAM-downloader was sent.. Phone is still stuck on the Moto Logo untill I remove the battery. If I remove the battery Phone starts.
Am I missing something?
As far as I remember, once you flash pudding the phone will indeed seem unusable. Immediately after flashing pudding you need to go into fastboot and run the oem unlock commands, then you need to flash a custom recovery, then boot into recovery and flash a custom ROM. You miss any of these steps and the phone will very likely not boot.
ravilov said:
As far as I remember, once you flash pudding the phone will indeed seem unusable. Immediately after flashing pudding you need to go into fastboot and run the oem unlock commands, then you need to flash a custom recovery, then boot into recovery and flash a custom ROM. You miss any of these steps and the phone will very likely not boot.
Click to expand...
Click to collapse
The problem is that i cannot flash pudding since I get an error message after the extracting process when the phone is suppose to reboot and flash itself. It just reboots and stays with Motorola logo (RSD Lites gives me the error) and phone freezes untill I remove battery. After that when I power on the phone it just loads normally.
So the problem is that I cannot flash pudding.... simply because phone dosnt reenumerate after reboot....
Bump ...
I want to add that the phone dosnt have backlight in boot menus (ak. background light is turned off but i can still see the options in boot menus)
Also I am not able to install OTA Updates I get a triangle on the screen and phone boots into os with failed to update message.
Else phone is fully functional. I havnet done anything except rooting the phone and doing the tethering and webtop over hdmi hack.
m140n1 said:
Bump ...
I want to add that the phone dosnt have backlight in boot menus (ak. background light is turned off but i can still see the options in boot menus)
Also I am not able to install OTA Updates I get a triangle on the screen and phone boots into os with failed to update message.
Else phone is fully functional. I havnet done anything except rooting the phone and doing the tethering and webtop over hdmi hack.
Click to expand...
Click to collapse
Try this automated tool. There are several options to choose from.
Download tool here.
Related
I just tried unlocking the BL from my official AT&T gingerbread using this guide, I tried flashing the sbf file with RSD and it got stuck and now my phone stays at this with the difference that mine gives me the option to try fastboot, RSD mode, Android Recover and another pletora of options I'm not sure i want to name.
So being able to try RSD again, i tried flashing this and it was appearently working but when it tried to set the device on BP Pass through mode, the device would go back to the Infamous screen and it wouldn't move from there.
Am I screwed? Do i have option?
I'm going to try to flash the stock FW to see what happens
Kenchinito said:
I just tried unlocking the BL from my official AT&T gingerbread using this guide, I tried flashing the sbf file with RSD and it got stuck and now my phone stays at this with the difference that mine gives me the option to try fastboot, RSD mode, Android Recover and another pletora of options I'm not sure i want to name.
So being able to try RSD again, i tried flashing this and it was appearently working but when it tried to set the device on BP Pass through mode, the device would go back to the Infamous screen and it wouldn't move from there.
Am I screwed? Do i have option?
I'm going to try to flash the stock FW to see what happens
Click to expand...
Click to collapse
use the automatic unlock tool found here:http://forum.xda-developers.com/showthread.php?t=1182871&highlight=automatic
do option 1 then option 3 (only use option 3 if on gingerbread) and you're good to go
Fastboot then use fastboot oem unlock command on PC. Reboot and it should work.
Sent from my MB860 using XDA Premium App
Thanks, I'll try it out and post back
I forgot to mention that my phone seems to be low on battery. Does it charge if it's not on the OS?
Noob Killed his phone
Hello, First time Poster here, please bare with me...
I really shouldn't of touched this.....
I have an Atrix w/ the newest updates to it, and attempted to unlock the phone. Everything started well, then it failed while writing to the device. Now, when I attempt to boot, I get the similar message of
SVF:405;1:2
Failed to boot 0x1000
With a 14 available options. I can get into fastboot, though I honestly am not sure what to do from there. I have the fastboot s/w downloaded, along with the gingerbread OS.
Did I just kill my phone?
I haven't still fixed mine because of the battery, I still have to find an external charger. Though, you can try the link from above.
Ok, I did the steps and now my phone is at a screen with the motorola logo with the dual core name on it and it has the word Unlocked on top of it.
What should i do?
the boot screen with motorola logo and unlock in corner will take awhile to load usually like 10 minutes but if it doesnt load for example i let mine sit for an hour and never loaded i just took the batter o and restart it and it rebooted and worked but use that as a last resort give it some time!
Omg i just fixed it!! Thx for the help!!
Mrniceguy0921 said:
the boot screen with motorola logo and unlock in corner will take awhile to load usually like 10 minutes but if it doesnt load for example i let mine sit for an hour and never loaded i just took the batter o and restart it and it rebooted and worked but use that as a last resort give it some time!
Click to expand...
Click to collapse
i think if the phone can be detected by PC, it should be a soft brick.. it is unfortunate my phone is booting loop and can not be read by PC, you're better than me..
Hey folks,
I'm having some issues with my ATT Atrix. The phone keeps rebooting at the "Rethink Possible" screen. I bought this phone off of somebody on CL. I actually had the phone make it past the att screen a couple times. It made it to the setup up Motoblur screen but when I clicked start it just skipped it and takes me to the "Emergency Calls Only" screen. However the phone would just restart eventually at this screen as well. When the screen timed out I could not get the screen to turn back on at this point unless I unplugged the USB cord and plugged it back in. When the phone was on the Emergency Calls screen, my computer did recognize the phone and it did launch the motorola website. While I had the phone at this screen it did say that it had to force close android.process.com. I am coming from a captivate with rooting and flashing roms so I am familiar with Android. I am just trying to figure out where the problem could be with my Atrix. I am hoping somebody can point me in the right direction. Thanks for your time!
Your best bet will be to SBF that back to stock. Have you tried that yet? If not search for RSD Lite and SBF in the forums. There are several links and guides.
Is it unlocked?
I am not sure if it is unlocked as I cannot get past the emergency call screen. However, I will search SBF and research that option of setting it back to stock. I know when I flashed roms on the Captivate I would enter into recovery mode. I see in the Atrix that I would have to use Fastboot? The only reason I am worried about flashing a rom is that the phone reboots on its own so I would not want to hard brick it if it rebooted during a flash.
If it's unlocked you should see the word "unlocked" in the upper left corner of the boot logo screen, unless it was unlocked then flashed back or fruitcake in which case it will not say unlocked.
You should not have issues flashing from recovery if you have enough juice in your battery, which you maybe don't if you have been letting it sit rebooting. The rebooting is more than likely caused by an issue with a kernel, ROM, etc. Think of recovery as being similar to the BIOS on a PC. You enter into BIOS before the OS boots, etc., and this is before all the hardware has initialized and drivers have loaded, so the problem causing the reboots should not exist at that time. I would definitely try flashing a different ROM, and also a stock kernel.
It never said unlocked when I got the phone to turn on. I am having trouble getting the phone to turn on this time. I have downloaded RSD Lite and the 4.5.91 .sbf file to flash. I am just having trouble getting the phone started. Are there any ways to force the phone on. When I press the power button the green LED stays lit but nothing comes on the screen. When I plug into the charger it shows the moto symbol then goes to the Battery charging screen. Im not sure if the battery is correct because it says BHX5 1500mAh on the battery. Thanks for your help guys!
Update: I can get the phone into Fastboot and then Android Recovery Mode when the phone is plugged into the wall charger. However when I connect the phone to the computer via USB it just shows the green led when the phone is powered on. Anyway I can get the phone to boot into Fastboot while connected to the computer via USB?
Bump. Any way to get the phone to turn on when plugged into the computer or anyone know why there would be an issue of the phone turning on when plugged into the wall charger but only showing the green led when plugged into the computer? The battery shows 100% charged. Thanks
Update: I got the phone into RSD mode and flashed the 4.5.91 sbf but the phone only goes to the Emergency Call Screen. Is there anything else that can be done?
nishith611 said:
Update: I got the phone into RSD mode and flashed the 4.5.91 sbf but the phone only goes to the Emergency Call Screen. Is there anything else that can be done?
Click to expand...
Click to collapse
Did you fastboot -w before flashing the sbf? (Guess you don't really need to when flashing a sbf)
What may also help is flashing the boot.img file from whatever ROM you are using via fastboot.
Don't know if this will help, but it solves an issue when flashing to a different ROM from CM7, so maybe will help for you.
I know this might sound dumb, but do you have a sim card installed? Also, try to boot into recovery and just do a factory reset. @CaelanT already pointed out that this should be unnecessary since you flashed an sbf but it wouldn't hurt to try.
nishith611 said:
Update: I got the phone into RSD mode and flashed the 4.5.91 sbf but the phone only goes to the Emergency Call Screen. Is there anything else that can be done?
Click to expand...
Click to collapse
EDIT: I reread the OP and realized he had already tried to bypass the start screen.
That is not the correct battery. That is actually a battery used for the Droid X/X2. It seems they have pulled a switch-a-roo on you. (Probably because the Atrix battery could be used as an "Extended" battery in the DX/DX2) Anyways, it should still work but you can find the correct battery online, it should be a BH6X and should have a capacity of 1880/1930mAH.
nishith611 said:
...Im not sure if the battery is correct because it says BHX5 1500mAh on the battery. Thanks for your help guys!
Click to expand...
Click to collapse
Thanks for the reply. I tried to get the phone into recovery mode. I get to the Exclamation Point screen but it gives me no options for a factory reset. I saw that you have to touch the lower right hand side of the screen, but this doesn't do anything for me.
As far as flashing the boot.img file for the rom that I used. I flashed the stock 4.5.91 motorola rom. How can I find boot.img and would I flash it using RSD?
Also would it help if I flashed a custom rom instead of the stock Motorola 2.3.4 rom?
Could the battery not being the BH6X rom be the issue for it not getting enough power to stay on by itself?
Thanks for the help guys, I really appreciate it!
No, the sim card was not installed during the flash. However, I did install the sim card afterwards but the phone boots up and goes to the big green battery charging screen and does not go any further. However when the sim card is not plugged in I can get the phone to go to the Emergency Call screen.
nishith611 said:
As far as flashing the boot.img file for the rom that I used. I flashed the stock 4.5.91 motorola rom. How can I find boot.img and would I flash it using RSD?
Click to expand...
Click to collapse
The following are the instructions for flashing the boot.img. this was the solution to bootloops when trying to restore to a different ROM after CM7, but as I said previously, you never know if it will help or not:
1.Open up the Zip file of your current Blur ROM (Ninja, CherryBlur, Alien, etc.)
2.extract the boot.img file and copy to the directory where your fastboot is.
3.Pull phone battery & reinsert
4.Power on phone and go straight to Fastboot mode (Power + Vol Down)
5.Type "fastboot flash boot boot.img" (exclude quotation marks)
6.Once flashed, reboot phone using "fastboot reboot"
Sorry, don't know how to extract the boot.img from a sbf. Did a quick search and couldn't find instructions. Not something I have done before. Maybe someone else can help with this. I don't even know if this will work, but anything is worth a shot when you are stuck.
<edit> Which CWM are you using?
You can flash Romracers via fastboot if you are not using it. This may help you get into recovery.
Update: I got the phone to recognize the sim card and make phone calls and get wifi active. But the phone still reboots by itself. I can use all the functions of the phone except it just reboots by itself. I got into the About phone section and it says
Android: 2.3.4
Kernel: [email protected] # 2
I can get into the Android Market as well as everything else. Could this be a hardware issue that causes the phone to reboot by itself within a minute or so?
Edit: I can get the vol up and down buttons to work while the phone is working but the power button is not responsive to let me power the phone off. Could a hardware issue with the power button be causing the constant reboot loop?
Update: I got the phone to function with the OS working just fine (phone calls, texts, emails, etc..) but it keeps restarting on its own. The power button still does not work however, could this be a hardware issue? Thanks
There's a TL;DR at the end !
Hi - I hope you will be able to help me !
I have a XT910 Motorola Razr from Rogers in Canada.
I've had a Nexus S for a long time and I guess I wasn't prepared for a phone that wasn't as friendly to modding and flashing.
Before trying to flash a version of CM10 found here in the forums, I installed CWM Touch and made a nandroid backup - standard stuff.
What I didn't realize until it was too late is that booting into recovery DOES NOT boot CWM Touch - but rather the regular android one - the one that does not allow you to do much other than to factory reset.
I found out about RSD Lite but not until my battery wasn't charged enough and couldn't do anything about the phone.
I searched for the longest time on a LOT on different forums about how I could fix this and resorted to getting a factory cable - which works.
So, now, I can flash stuff using fastboot. Great, right ? Well, I still can't get things working.
RSD Lite doesn't detect my phone, and I believe that's because ADB doesn't detect it as well - so I tried that alternative way to flash fastboot files provided by the eternity project.
I've tried various fastboot packages but to no avail.
The best I can do is to get past the motorola logo - then black screen. Otherwise, I get boot or flash failures and get sent back to fastboot.
When the phone is on the black screen and that I plug a USB cable to my phone, Windows sees the device but it doesn't recognize it - I assure you I've tried all the different drivers to try and get it to work. Nothing.
Worth mentioning - I often get errors "Preflash validation failure" when trying to flash stuff.
I really feel I could fix this issue by flashing an IMG version of CWM touch or some other sort of recovery so that I can recover using a nandroid but they are no where to be found ! I can't believe that all recovery options are installed by APKs.
Any ideas ?
TL;DR, XT910 went boot looping after trying to flash CM10 - resorted to getting a factory cable and even then, can't get the phone back into working condition. Phone is detected by fastboot but not ADB.
Thanks !
first... the battery is the problem
this article can help...
How to Boot your Phone on Low Battery with Fastboot Flash Failure
To boot your phone on low battery where you get stuck on fastboot flash failure, hold down Volume Up and Volume Down then plug in “AC” USB charger to your Droid Razr. This will give you the bootloader menu upon where you can choose “Normal Recovery” to boot. If your phone doesn’t boot here, it will at least re-charge the battery normally instead of being stuck on fastboot flash failure which will re-charge your phone “very very slowly”.
So I bought myself an Atrix last night, its completely mint. Except the phone is bricked.
I've done basic flashing on my Samsung Nexus i9250 and on other LG's and HTC's so I understand the surface level stuff.
Now, the Atrix powers on and hangs on the Motorola Logo says "UNLOCKED" in the top left corner, (I'm assuming bootloader is unlocked)
And I get a modem did not power up (0) shortly after it hangs for a while.
I've read on another thread that this is a hardware issue and it can't be fixed via flashing.
I'm hoping that's not entirely the case, the only thing I can do is boot into Android (no BP), and it restarts after a minute or so.
And I can boot into recovery, this phone has TWRP, which I did not put on, and am not used to.
Anyway I've been trying to revert to a stock rom, (assuming bell because I'm in canada) but I can't get my fastboot to go.
It just stays on "starting fastboot protocol" and RSDlite doesn't recognize it. (battery at full charge)
That is about the jist of it.
I'd like to see if a stock rom, recovery and radio image will get this guy up and going again.
Hopefully I can switch TWRP for CWM, or back to stock with fastboot and RSDlite, I don't totally know the process.
Thanks for any and all help in advance
I've got CWM now,
I think I maybe having a hardware issue.
Everytime I try to flash radio's through CWM or RSD, I get some sort of failure.
I can flash radio's through fastboot but it doesn't seem to help my situation.
Currently I'm flashing with RSD, first time around my device was an NS Flash Olympus and it failed at writing BP.
Now its an SE flash Olympus And I'm trying the same SBF.
It seems to fail when it switches to BP Pass through mode.
:/
Edit: In RSD everything is N/A
I can boot into Android on the no BP setting.
And flick threw a few menu's then the phone would die.
Baseband is unknown, I managed to get there in settings.
Anyone have any idea as to what is wrong here?
I'd like to know if I'm SOL so I can let the atrix gather some dust on the shelf.
Yep, it sounds like somwthing is messed up on the modem Hardware
Enviado desde mi MB860 mediante Tapatalk
I think I bricked my device big time in an effort to return to stock. I flashed 4.5.141 and later got a system update while bootloader was unlocked. I got Failed to boot 4.
Later, I tried to relfash the same 4.5.141 sbf and it failed to flash and I got "Failed to boot 1".
Now, I thought I will try to flash again using RSD lite and tried to get into RSD Mode using Vol Down+Power. I am supposed to see options to navigate to RSD and press Vol Up. The first option appears for half a second and the screen turns off.
I am not sure what this behavior is. However, it stays on if battery is low. It stays in NV Flash mode with a message "Battery too low... blah"
I tried to put into fastboot mode and did "fastboot reboot-bootloader". It rebooted but it does not get into RSD Lite mode. It just shows Failed to boot 1. I know how to fix Failed to Boot 1 issue. But this failure to enter RSD mode is killing..
Any one encountered this? Any help here please?
I got out of this problem by using sbf_flash and unlocked the bootloader (with pudding one). That unlocked my bootloader and my Vol Down+Power menu was accessible. And, I went to recovery, performed a wipe and rebooted.
Voila.. It booted very well. I am now in the latest stock. I went all the way from 2.3.6->4.1->4.4.4->Mokee 5.0 and then back to sweet old stock 2.3.6.
My experience with Atrix had been awesome from 2013 where i installed CM 10. It is a great phone and now it works as a music player for me.