Somehow the micro usb port on the phone (the charger) has been mashed up inside, i think it may have been due to someone trying to fit the wrong charger into it.
a shop said it'd have to get sent away,
i was wondering if their is a place to send it to get fixed or it it fixable ?
atm im having to charge another battery with a docking station and swap battery's because it wont charge,
it did work a little earlier on today, charging. but i can see the insides are pretty well destroyed.
it looks like the piece can be removed and a new one soldered on,
any ideas ?
thanks.
Honestly, if somone on here knows how to fix hardware issues I am sure they can lend you a hand but otherwise you will have to go to a repair shop and have it serviced. Just make sure that everything is complete stock and bootloader is in locked state just to be safe. If you don't want to send it back through the mail you can always take to a sprint authorized repair shop.
If you want to attempt it yourself here you go
http://www.youtube.com/watch?v=jxiv3x88eRg
http://www.youtube.com/watch?v=fdxrPWrVgR8
http://www.youtube.com/watch?v=I-HlZQKQzoQ
http://www.ebay.co.uk/itm/New-HTC-E...K_Replacement_Parts_Tools&hash=item20ca337adf
Thanks guys, ive been looking online and some places seem to say they can fix it,
that video is just jokes, he faffs around with the thing im sure he ha no idea what hes doing.
ive found usb ports for other htc models just not the evo 3d.
ive realised it is quite a common problem
its charging via my docking station... just. obviously the internals of the micro usb are mashed up, and i know the replacement needs to be soldered on,
ive looked on some websites but cannot find anywhere to fix it.
its ok atm as its charging via dock, and i have a spare battery, also i can just take out my sd card to add stuff but it i rather annoying abd id like it fixed asap.
You could always use WiFi file explorer,of course WiFi is required but you can read and write the sdcard from your ip address,
Signature (Don't ask me for help, couldn't careless if your phone explodes)
strange thing is its connecting via my dock.. and charging, eventho the insides of the micro usb are mashed up..
it wont work with any other cable just in the dock...
im guessing the dock pin is slightly larger thus allowing a connection ?
Related
Thread for hardware mods
POSTING INTERNAL tf101 pictures
like 3g dongle ? internal sd cards? ssd?
removing the battery for 2 HDD 500go?
finding sd cards hubs? usb to sata cables?
? there is a place in the tablet for a 3g dongle?
there are 2 screws under the upper rubbers and the dock open easy
there is a lot of spaces avaible
My MIFI might actually fit in there, all I would need to do is supply it power somehow.
I'm no hardware engineer though, but if thats possible it would save you from the driver issues with a 3g dongle.
I wonder if it would be possible to check which pins from the adapter connect to USB - so we can make DIY USB adapter for those without a dock.
hmm adding an hdd would be very interesting, sata won't be very hard, powersupply will be.
Sent from my O2x with CM7
This is what I was looking for, looking to do some mods to the dock.
Thanks Markolino72.
Internally mount and wire a 32gb memory stick to the USB port so you get a 32gb hard drive added whenever you dock It might even have enough room for a portable USB hub so you don't lose use of the external usb port?
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
ydnality said:
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
Click to expand...
Click to collapse
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Regards.
In regards to the hardware mods, that really looks amazing. Would love to put in my mifi there as well, attach it via USB to charge = your own 3g model Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well. Only a few thoughts.
Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well.
Click to expand...
Click to collapse
it's a good thought but the mifi I have (novatel 2200) wont work without the battery, for some reason if the battery is bad or removed you cannot run usb, it must be the way they have the power run through the battery or charging. Not sure if all are like this or not.
andrewklau said:
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Click to expand...
Click to collapse
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Surprising how much wasted space there seems to be in the dock -- it's nowhere near as tightly packaged as the tablet itself. Looks like Asus can optimize the size or fit some more features in future versions, if they want...
Let me see if I am thinking correctly...Your saying using something like mifi installed via USB wires (will it be always on?) then connect via WiFi on your transformer? So basically your putting the mifi in a case that can never be opened without a screwdriver? I guess one would always have access for your other devices as well as long as the TF is in the vicinity.
P.S. I think I think this is a good idea, not decided though. I like to think of it in a real world application.
there is another post with a guy putting in an SSD, but it bulges at the keyboard. A 32g SD card would be nice.
Sent from my Transformer TF101 using XDA Premium App
typci said:
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Click to expand...
Click to collapse
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
tanguita said:
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
Click to expand...
Click to collapse
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
knoxploration said:
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
Click to expand...
Click to collapse
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
tanguita said:
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
Click to expand...
Click to collapse
Yeah, actually, I hadn't realized that but it does say it clearly on the product warranty page:
"Brazil and South American countries don’t support global service"
http://support.asus.com/warranty.aspx?SLanguage=en&p=20&s=16&m=Eee Pad Transformer TF101
took mine apart also and there is quite a bit of room.
i plan on putting a 128gb usb flash drive inside the dock and soldering onto the usb connections once i get all the bits in.
Any bigger pictures? Are the screws under the rubber feet?
just two screws under the rubber feet near the hinge then it just pulls apart from the top
had to take mine apart as the spring/clip mechanism for the sd card wouldnt lock the card in.
now the card is stuck in with no nails haha a simple fix.
This is good news. I hacked a Crystal HD decoder card (pcie), USB wifi dongle, a logitech nano receiver, and a 4 port micro usb hub (from a touch screen setup) into a Dell mini 9 and there was absolutely no room compared to this.
They even have covers for the USB ports, so if you remove a header and solder wires up you just have to hot glue / epoxy that cover from the back and you are money. Looks clean and stock.
I have an old 64 GB thumbdrive that might find a new home. Maybe a 1.8" usb HDD would fit in there with the battery, without the battery who knows.
Hey guys, in one of the stupidest, impulsive and least prepared actions I have ever undertaken, I seem to have damaged my charging port. I cleaned the charging port with a pin, and succeeded in cleaning it, however, now my phone won't charge. I have no idea why, as the charger goes in well. My guess is that I scratched some core component, or the like? The only thing is, I would have assumed these parts to be pretty hardy, as they're exposed to everything in our pockets, etc. Has anyone got any information or experience in the are.
I apologize for such a noob question, but any help is appreciated!
P.S When I plug my phone into my computer, a message pops up saying something about over powering or something?
dyspoid said:
Hey guys, in one of the stupidest, impulsive and least prepared actions I have ever undertaken, I seem to have damaged my charging port. I cleaned the charging port with a pin, and succeeded in cleaning it, however, now my phone won't charge. I have no idea why, as the charger goes in well. My guess is that I scratched some core component, or the like? The only thing is, I would have assumed these parts to be pretty hardy, as they're exposed to everything in our pockets, etc. Has anyone got any information or experience in the are.
I apologize for such a noob question, but any help is appreciated!
P.S When I plug my phone into my computer, a message pops up saying something about over powering or something?
Click to expand...
Click to collapse
Dont know anything about the overpowering error you got , but my phone was charged with a charger that sat next to a mouldy wall for too long (disgusting!) and the port was filled with black mould. I placed this into my phone and of course buggered my charging port. I managed to fix it by getting rid of as much crap as i could manually, then bought a can of compressed air and blew out the rest, which did the trick and now it works faultlessly again....
Well, you might have damaged the connectors or - if you did that with a metal pin - you might have caused a short circuit.
When you connect it to PC - it's not charging i guess - but does it allow you to transfer files via USB ?
Anyway, try clearing battery status in recovery, using another cable/charger.
If it won't charge from charger and PC i guess you need to take it to service center.
Woah, you guys reply really fast
I cleaned it, and got a tonne of crap out, but that is what messed it up. :|
I am guessing I damaged the connectors, but I would have assumed if the pc could detect it, a much less sophisticated component would be required for charging.. ahh.
I can't charge it, so I guess the service centre is the only option. Damnit.
i think the charging port has damaged so u have to change it
Guys, I'm convinced the usb connector on my 9 month old TP is defective and gets worse each time I use it. I had bought a touchstone charger to ease the connector wear but still, I was eventually having problems with USB data connectivity using store bought cables. I even sent my TP in to fix the connector and when I got it back, still no USB connectivity. Just a completely wiped TP. So HP sent me one of their "genuine" silver dot cables and low and behold it worked fine. (My original cable was lost)
Now, months later, I'm having problems with the USB data connection again. I either get the "Not enough current message" in WebOS or no MTP USB symbol in CM9. Sometimes the PC will chime positively but with an error message (can't detect device). I received another genuine HP cable and it behaves the same as the other one. Inserting them normally, they appear to be in tight, the PC will chime but Windows will say that there's a problem, can't detect device. The only way to get it to work is to insert the microusb side at a 45 degree angle tilted downward and hold it in for 5 seconds, then (ever so slowly) release the pressure to the connector. 50% of the time I'll get a Windows message that says the USB is degraded and run slower than normal (which I think means it thinks its in USB1.1 slow xfer mode) and 50% it works fine at USB 2.0 (until I pull the cable out of the connector). I also have 2 store bought cables that won't ever successfully connect to USB with the TP but work fine with my Samsung cell in both charging and xferring music over to the phone.
So what I'm getting at here is that no standard microusb cable is the same and that there must be something special about the HP genuine one. Do these cables have a resistor on pin 4 ID tied to GND pin 5? Even so, I think what is wearing the most is pins 1 & 2 and maybe 3 (VCC and the data pins) which is why it may only work by concentrating on seating those pins first. Does it make sense that the 'can't detect device' message comes up with just the data lines and ground connected but no VCC? For that matter, why would the battery symbol in CM9 always show the lightning bolt assuming pin 1 VCC is not connected?
I'd appreciate any responses from other members here since I believe without USB the TP could be bricked in case some boot code gets corrupt and you are forced into WebOS recovery mode. This has never happened to me yet and I've installed a lot of nightlies but it COULD happen, no guarantees. What is inevitable is my connector will eventually wear out and my TP will only live until the bootloader DOES get corrupt, hopefully later than sooner. This could be the case with all TP's. Just imagine if in a couple of years everyone's TP's USB port goes bad. Sounds like the devs should figure out a way to fix a bricked TP wirelessly, if that's at all possible.
Thanks,
synchron
One of my Touchpad's had the same problem in Webos it said using wrong charger may not charge or something similar and with Android ie nightly the charging signal came up but it did not charge.
I spoke to HP and pointed out that I have 2 Tablets and that swapping leads or chargers made no difference all combinations worked on one but not the other.
They agreed to fix it and replaced the part. It is now working fine. And as with yours my computer failed to recognize the tablet properly.19 times out of 20 on the one time it did I was able to back up and remove Android before HP picked it up.
I would send it back under warranty or if that has expired state that it was preexisting. Otherwise as you said it is going to become pretty much unusable.
Don't let them fob you off.
Good luck
spaceosc said:
if u bought it during the fire sale u have about a week till (8/20) the one year warranty expires.
http://kb.hpwebos.com/wps/portal/kb/na/touchpad/touchpad/wifi/supportservices/page_en.html
go to palm support and CHAT with them. do not call cuz that cost money.
once u get an RMA they will send a box and take care of Shipping.
then go here to wipe and remove android
http://forum.xda-developers.com/showthread.php?t=1426244
once wiped send it in and your speaker will be fixed, it will take about a week.
Click to expand...
Click to collapse
from another thread
sstar said:
One of my Touchpad's had the same problem in Webos it said using wrong charger may not charge or something similar and with Android ie nightly the charging signal came up but it did not charge.
I spoke to HP and pointed out that I have 2 Tablets and that swapping leads or chargers made no difference all combinations worked on one but not the other.
They agreed to fix it and replaced the part. It is now working fine. And as with yours my computer failed to recognize the tablet properly.19 times out of 20 on the one time it did I was able to back up and remove Android before HP picked it up.
I would send it back under warranty or if that has expired state that it was preexisting. Otherwise as you said it is going to become pretty much unusable.
Don't let them fob you off.
Good luck
Click to expand...
Click to collapse
spaceosc said:
from another thread
Click to expand...
Click to collapse
Thanx for your prompt responses. I bought my TP at the 2nd fire sale through BB in early Nov so I still got a few more months but I would rather wait a bit more since they did nothing the 1st time around. I think the connector is on some daughter board along with the vibrate device which is soldered to the main board. Doesn't sound like a big deal to repair it. Still, what makes the HP cable different then the others? Are there known cables I can get online that might be made better to always work and make better contact than the HP ones?
Synchron
synchron50 said:
Thanx for your prompt responses. I bought my TP at the 2nd fire sale through BB in early Nov so I still got a few more months but I would rather wait a bit more since they did nothing the 1st time around. I think the connector is on some daughter board along with the vibrate device which is soldered to the main board. Doesn't sound like a big deal to repair it. Still, what makes the HP cable different then the others? Are there known cables I can get online that might be made better to always work and make better contact than the HP ones?
Synchron
Click to expand...
Click to collapse
dont wait, ive sent my TP in 3 times, 1st time for charging port, 2nd for a crack around the speaker, 3rd for a busted speaker.
spaceosc said:
dont wait, ive sent my TP in 3 times, 1st time for charging port, 2nd for a crack around the speaker, 3rd for a busted speaker.
Click to expand...
Click to collapse
Thanks for your advice. Did they fix everything that was intended? Was turn around time no longer than 2 weeks for each repair? When was your last repair (busted speaker) done? Is your serial number the same or did you ever get a replacement (meaning a refurbished one) back?
Thanks
synchron50 said:
Thanks for your advice. Did they fix everything that was intended? Was turn around time no longer than 2 weeks for each repair? When was your last repair (busted speaker) done? Is your serial number the same or did you ever get a replacement (meaning a refurbished one) back?
Thanks
Click to expand...
Click to collapse
i keep track of the serials and they always came back the same. i have more than one pad and i asked for one to be replaced completely. we will see if that happens. but they fix only what u ask for and nothing else.
it can take longer depending on Weekends. takes 2 days to get your box, then 2 days to get it to HP, then 3- 4 days to get your fixed unit. its all done thru UPS, cant send it out on the weekends or receive it
spaceosc said:
i keep track of the serials and they always came back the same. i have more than one pad and i asked for one to be replaced completely. we will see if that happens. but they fix only what u ask for and nothing else.
it can take longer depending on Weekends. takes 2 days to get your box, then 2 days to get it to HP, then 3- 4 days to get your fixed unit. its all done thru UPS, cant send it out on the weekends or receive it
Click to expand...
Click to collapse
Thanks, you are giving me hope to try again while my warranty is still good. Maybe I'll put a big note on the screen PLEASE REPLACE USB CONNECTOR - wouldn't hurt.
Synchron50
I know this is really old, but im finding my self with similar issues and no warrenty
synchron50 said:
Guys, I'm convinced the usb connector on my 9 month old TP is defective and gets worse each time I use it. I had bought a touchstone charger to ease the connector wear but still, I was eventually having problems with USB data connectivity using store bought cables. I even sent my TP in to fix the connector and when I got it back, still no USB connectivity. Just a completely wiped TP. So HP sent me one of their "genuine" silver dot cables and low and behold it worked fine. (My original cable was lost)
Now, months later, I'm having problems with the USB data connection again. I either get the "Not enough current message" in WebOS or no MTP USB symbol in CM9. Sometimes the PC will chime positively but with an error message (can't detect device). I received another genuine HP cable and it behaves the same as the other one. Inserting them normally, they appear to be in tight, the PC will chime but Windows will say that there's a problem, can't detect device. The only way to get it to work is to insert the microusb side at a 45 degree angle tilted downward and hold it in for 5 seconds, then (ever so slowly) release the pressure to the connector. 50% of the time I'll get a Windows message that says the USB is degraded and run slower than normal (which I think means it thinks its in USB1.1 slow xfer mode) and 50% it works fine at USB 2.0 (until I pull the cable out of the connector). I also have 2 store bought cables that won't ever successfully connect to USB with the TP but work fine with my Samsung cell in both charging and xferring music over to the phone.
So what I'm getting at here is that no standard microusb cable is the same and that there must be something special about the HP genuine one. Do these cables have a resistor on pin 4 ID tied to GND pin 5? Even so, I think what is wearing the most is pins 1 & 2 and maybe 3 (VCC and the data pins) which is why it may only work by concentrating on seating those pins first. Does it make sense that the 'can't detect device' message comes up with just the data lines and ground connected but no VCC? For that matter, why would the battery symbol in CM9 always show the lightning bolt assuming pin 1 VCC is not connected?
I'd appreciate any responses from other members here since I believe without USB the TP could be bricked in case some boot code gets corrupt and you are forced into WebOS recovery mode. This has never happened to me yet and I've installed a lot of nightlies but it COULD happen, no guarantees. What is inevitable is my connector will eventually wear out and my TP will only live until the bootloader DOES get corrupt, hopefully later than sooner. This could be the case with all TP's. Just imagine if in a couple of years everyone's TP's USB port goes bad. Sounds like the devs should figure out a way to fix a bricked TP wirelessly, if that's at all possible.
Thanks,
synchron
Click to expand...
Click to collapse
Hi all. I know this thread is really old, but I'm finding myself dealing with similar issues. And I'm obviously out of warranty. I can't get windows, linux, or Toolbox to pick up the USB. I'm actually in a worse case scenario mention here and am stuck in meboot, TWRP, and WebOS recovery, because I had wiped the rom. It must be an issue with the USB port, I've lost track of my original Hp touchpad OEM cable, and have tried every USB cable I can find. Any help would be appreciated.
I have a second hand Galaxy S2 which was unlocked to all networks and randomly the phone would connect to driving mode. I used GoLauncher EX to delete Voice control but then it started showing that it was charging constantly. After a lot of research I found the problem was in the charging port.
I ordered a new charging port online and I've put it in instead of the old one and now the charging problem is gone, but now my phone gets no service on a Three UK sim, I'm quite sure it wasn't on Three UK to begin with.
Is it possible that changing the charging port might have locked the phone to the original carrier again?
and is there anyway to unlock it(without root) or get it working again a different way?
(This is my first post. Forgive me if I've made any mistakes. )
Got quite a few views. Does this mean no one has any idea on what it could be?
Take a look at the antenna wire sometime you touched it and it's not connected properly
Yeah I have seen a lot of people lose signal who replace that port. I'm pretty sure it has something to do with the antenna. Make sure you have knocked it by mistake
Sent from my GT-I9100 using xda app-developers app
I experienced the same problem with my Samsung S2. I had destroyed the charging port by being careless when charging it which meant my phone would not charge at all; although if I was lucky I would get about 10% charge every day.
To resolve the problem, I bought a cheap charging port flex cable off ebay for about £4.00 which I thought was a bargin. After taking the phone apart (with help from a YouTube video) I replaced the port, turned the phone on and it charged perfectly. Then all of a sudden I lost all signal. I moved around the house, hoping to get the slightest bit of signal but no, nothing. I did a lot of research online as to why this has happened and everyone said it was to do with the antenna cable that runs along the left hand side of the phone so my immediate thought was to buy a new one. I did a factory reset to see if that helped but it did not. As I was desperate, the following day I went into town to see if I could find a shop that sold an antenna wire. I went in shop after shop but nowhere sold what I was looking for. I went into a shop and described my problem to the man behind the counter, and he knew exactly what was wrong. On the flex cable there is "REV" followed by a number, and he told me that if the replacement number is not the same as the original then the phone will have no service.
In the photos you will see my original cable that was "REV2.3" and my replacement cable that was "REV2.2".
Long story short... when replacing the charging port make sure the replacement flex cable has the same REV number as the original otherwise you will have no service. Your problem is not related to the antenna wire.
I hope this helps!
solution posted here
http://forum.xda-developers.com/galaxy-s2/help/weak-signal-reception-changing-micro-t1950114/page4
Okay so I made (tried to make) a USB OTG cable by taking the metal off the outside of the USB connector, then cutting and reconnecting the cable with red on black and green on white so it would be the same polarity as a female USB. i plugged a flash drive up and nothing happened.
Here is where my retarded moment comes in: I HOOKED IT UP TO THE COMPUTER WITH THE POLARITY REVERSED!!!!
Now it wont even boot up. :crying:
I have a HTC One (AT&T).
PLEASE HELP!!!
I also don't want to send it back because this will be the third phone in 3 months (1st: xperia tl soft bricked returned 2nd: xperia tl hard bricked returned 3rd: i hope it will still work, but i need your help). . i will take ANYTHING except for taking it apart (that's why there is geek squad but that costs money and I'm broke).
if i need to go into more detail i will but please tell me or else i wont know.
wires:
red----------black
white----------green
black----------red
green----------white
i think it blew a fuse, but if so how would i fix it? does it even have a fuse?:crying:
Oh dear! You've lived up to your name anyway. The phone is frazzled!
Next time get a schematic of the cable wiring or buy a cable. It'll be cheaper in the end.
Your phone shop should replace the phone though - just don't tell them your story
CtrlAltDelIrl said:
Oh dear! You've lived up to your name anyway. The phone is frazzled!
Next time get a schematic of the cable wiring or buy a cable. It'll be cheaper in the end.
Your phone shop should replace the phone though - just don't tell them your story
Click to expand...
Click to collapse
that is not what i wanted to hear but thank you anyways. :crying: :crying:
maybe since it wont boot up at&t wont have any way to know about the unlocked bootloader and cyanogenmod (they let me get a new phone for free even after rooting and bricking both my xperia tl's. All i had to do was say that the update broke itor the battery wouldn't hold any charge.) But I JUST got it two or three days ago so I feel very crappy now.
at least i have google voice on my computer and kindle fire.
WHY DIDN'T I WATCH THE STUPID VIDEO!!!! the answer is i am a freaking idiot.
When you say "phone shop", does best buy fit in that category? or is there any possible way to fix it from home?