Hi everyone I'm freaking out this is the second time i root my device s3 international the first one was with CF-Root-SGS3-v6.4 but after i installed the official jb for the uk i decided to root with Chainfire new root CF-Auto-Root v1.0 and now odin is stuck at just after i pressed start this is what it says in the message box:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-m0-gti9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
It's been like that for at least 15 minutes now I'm not sure what to do if it's safe to disconnect the phone or what.
Please help me
This is the exact same scenario as what I've had the last week. I just pulled my battery and USB cable and everything was fine. However do not try flashing a PIT file, as the problem suggests. I tried it and bricked my phone. I never found a fix for the mapping problem, my phone is off to warranty now.
Well, mine was very fast, a few seconds, nothing even close to 15mins so something went wrong for sure. The good part is that you'll probably won't have an issue to disconnect that and try again. Not sure how this works, but it probably doesn't mess with the bootloader. In that case you'll always have download mode and therefore can always try again.
Odin has hanged for me before (with my S1). Usually changing the USB port or/and rebooting computer and phone does the trick (provived you had everything working before and just hanged now for no apparent reason).
Krep3 said:
Hi everyone I'm freaking out this is the second time i root my device s3 international the first one was with CF-Root-SGS3-v6.4 but after i installed the official jb for the uk i decided to root with Chainfire new root CF-Auto-Root v1.0 and now odin is stuck at just after i pressed start this is what it says in the message box:
Pointless changing a working root for a BETA tool ..
Flash back CF root v6
jje
Click to expand...
Click to collapse
PIT means Partition Information Table.
If you even try flashing that, you will brick your phone.
Get pit for mapping error
I have tried to root my s3 using Odin 1.85 and cf 6.4 but always it sticks at the get pit mapping error.
It's a UK phone locked to the 3 network.
Any advice would be appreciated.
welshjoe said:
I have tried to root my s3 using Odin 1.85 and cf 6.4 but always it sticks at the get pit mapping error.
It's a UK phone locked to the 3 network.
Any advice would be appreciated.
Click to expand...
Click to collapse
I'm on three uk and use Odin3 v3.04 don't know weather that makes a difference
Never gets passed get pit for mapping on 3.04 too. Somebody please help.
Sent from my GT-I9300 using xda app-developers app
The other thing I found is that if I plug the usb in the front of pc while I'm on Skype with a usb mic also plugged in to the front of pc the same thing happens so it's like there is not enough power so try using a different usb port also unplug other usb things while u flash. Hope that sorts it for u bud
Sent from my GT-I9300 using xda app-developers app
CF Auto root is beta use the standard CF root 6.4 .
http://autoroot.chainfire.eu/
jje
After reading up on this it would appear that because it's locked onto the three network, I can't root it. Is this true?
Sent from my GT-I9300 using xda app-developers app
Mate I'm on 3uk rooted and rom did u try the usb thing I said about?
Sent from my GT-I9300 using xda app-developers app
The only thing plugged in is mouse. I've tried all USB ports but still the same.
Sent from my GT-I9300 using xda app-developers app
---------- Post added at 12:13 PM ---------- Previous post was at 12:08 PM ----------
It must be something very simple.
Sent from my GT-I9300 using xda app-developers app
sorry if this sounds daft , but you do have samsung drivers installed correctly on your pc ? usb debugging checked ?
Yep. Both set and installed.
Sent from my GT-I9300 using xda app-developers app
This is my build
Sent from my GT-I9300 using xda app-developers app
Only other thing I can think of are u using the official usb lead?
Sent from my GT-I9300 using xda app-developers app
Yes I am. I used it to do the official JB update using kies and everything went fine, first time.
Sent from my GT-I9300 using xda app-developers app
Is Kies completely shut down on your pc ? I read somewhere that it can cause conflicts when trying to use odin
I read it too so I uninstalled. I then downloaded the drivers only.
Sent from my GT-I9300 using xda app-developers app
Related
Hey XDA Members!
I have a problem with my Device.. If i wanna flash any kind of firmware, (flash via odin) i get this textbox :
Code:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> CODE_I9300XXALF6.tar.md5
<ID:0/003> NAND Write Start!!
The blue bar is full after 1 second ..this cannot be, it takes much longer if you flash an original firmware.. i read that there can be something defect at the s3? what can this be? i cannot flash any firmware because the blue bar is filled after 1 second and then nothing more is happening..
Please help me !
I have had this problem before try making sure kies isn't running on your computer see if that works.
Sent from my GT-I9300 using xda premium
i have no kies on my pc so this cannot be the problem
Possible faulty download.
jje
Sent from my GT-I9300 using xda premium
did you install the drivers??, you have to install the latest Keis for the drivers, and kill the application.
have downloaded from samfirmware 10 times for now
and my device is detected from Odin, so the drivers are installed
i don't really know what it can be
so_ony said:
have downloaded from samfirmware 10 times for now
and my device is detected from Odin, so the drivers are installed
i don't really know what it can be
Click to expand...
Click to collapse
try on another pc...i also had a problem with odin on my pc, but tryng with another one it went all right..
Dou you haw international Sgs3???
Sent from my GT-I9300 using xda premium
Had the exact same problem, had to reinstall the drivers for it and everything went ok
Also be sure to use the USB cable that come with your SGS3!
I remember that some people had issues using another USB cable...
Reinstall drivers bet it works
Sent from my GT-I9300 using xda app-developers app
maybe u can fix it with the tool "usbdeview"
hmm... installed kies with drivers but it is not working.. can be somehting defect or is it software based .. strange thing
so_ony said:
hmm... installed kies with drivers but it is not working.. can be somehting defect or is it software based .. strange thing
Click to expand...
Click to collapse
Just Root and use mobile Odin.
Sent from my GT-I9300 using xda app-developers app
Now make sure kies is not running crlt .alt.shift processes if you see kies
End process and try again
Sent from my GT-I9300 using xda premium
SlimJ87D said:
Just Root and use mobile Odin.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
next problem is root, if i install cf root the installation script is not running after successfull flashing it on the s3, it is booting normally and CWM Manager and SuperSU is not installed but CWM Recovery is there if i go into recovery modus, strange
Help! I flashes Siyah's kernel on my S2 (it was on stock 2.3.3) and now it won't boot and all I get is the i9100 logo and a yellow triangle with a warning sign. I have searched the forums and googled but can't find anything on this :/ I'm not sure if this is the "yellow triangle" most people seem to be talking about as I can't really do anything to "remove" it as they suggest.
Dexter_prog said:
Help! I flashes Siyah's kernel on my S2 (it was on stock 2.3.3) and now it won't boot and all I get is the i9100 logo and a yellow triangle with a warning sign. I have searched the forums and googled but can't find anything on this :/ I'm not sure if this is the "yellow triangle" most people seem to be talking about as I can't really do anything to "remove" it as they suggest.
Click to expand...
Click to collapse
I'm assuming you picked up the latest siyah version. Its for ICS not GB.
Download the file from Jokesy's post here. http://forum.xda-developers.com/showthread.php?p=32689470
Siyah for gingerbread and install it via Odin.
Sent from my GT-I9100 using xda app-developers app
Ah, Jesus. I'm such an idiot!. After reading the forums for hours making sure I wasn't gonna make a mistake I ended up flashing an ICS kernel on a GB rom.
Anyway, I did it but it is still stock at boot :s What do I do? Should I flash a stock unbranded ICS rom? I mean, those come with a kernel, right?
Flashing siyah through odin didnt work? Then you might want to install a new stock firmware. Download one from sammobile.com and install again via Odin the same way you installed siyah. GB or ICS (4.0.3 only to avoid risk of the emmc bug) and then try again.
It does come with the stock kernel.
The thread link I provided talks about a similar problem. Reading that might help too.
Good luck
EDIT: if youre unsure about your correct formware. this link will provide you the ICS firmware for most regions. Pick the one matching region if possible. Best signal reception and all that. http://forum.xda-developers.com/showthread.php?p=23562857
Sent from my GT-I9100 using xda app-developers app
I am tryiong to find a stock rom but all come in zip format and odin asks for .tar
Where are tar roms for odin? :S
You must unzip them
I did and the flashing on ODIN failed, I got this:
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100UHLPS_I9100UHLPG_I9100AROLP4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<ID:0/009> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
and now it won't but and I get: "firmware upgrade encountered an issue. Please select recovery mode in Kies and try again"
What do I do?
god please help me I can't flash anything, it keeps failing! Please keep in mind I come from a stock gingerbread rom. it is because the bootloader and everything is locked or something?
I tried this and it won't flash either: http://forum.xda-developers.com/showthread.php?t=1457458
Sorry. Kinda busy atm so this thread slipped my mind.
Which version of Odin are you using? Some report problems with 3.4.. use 1.85 if you can.
Ensure your phone has sufficient charge
Do you have your phone drivers installed? They should be.
Is KIES running in the background? Kill it. KIES is known to interfere with Odin.
Sent from my GT-I9100 using xda app-developers app
HAXTREME said:
Sorry. Kinda busy atm so this thread slipped my mind.
Which version of Odin are you using? Some report problems with 3.4.. use 1.85 if you can.
Ensure your phone has sufficient charge
Do you have your phone drivers installed? They should be.
Is KIES running in the background? Kill it. KIES is known to interfere with Odin.
Sent from my GT-I9100 using xda app-developers app
Click to expand...
Click to collapse
I tried with both 3.4 and 1.83 from the recovery package.
I don't know if I can charge it as when I plug it it displays the same "firmware upgrade encountered an issue" message and I am unsure weather it is charging or not. Anyway, I charged it to 100% before all this madness began.
I uninstalled KIES before trying all of this.
pd: no problem man, I'm not complaining to your or anyone, it's just I got really nervous and don't know what to do. Plus the phone is out of warranty.
GOT IT.
Problem: I was not pluging the phone DIRECTLY to a USB port (AND ODIN DEMANDS YOU TO PLUG THE PHONE DIRECTLY TO A USB PORT, SO DON'T USE HUBS, PCI CARDS OR WHATEVER). My computer's usb ports stopped working months ago so I bought a PCI-to-USB card to have USB ports.
Solution: After hours of googling I came across this XDA thread: http://forum.xda-developers.com/showpost.php?p=26748860&postcount=2
As you can see, he mentions what I said about ODIN (I learned it from him/her).
So the solution is to use ODIN with the mobile phone connected directly to the usb port
And to fix my problem: I just used the recovery package from here: http://forum.xda-developers.com/showthread.php?t=1457458
which worked beautifully.
You wouldn't believe I just came back online to pm you to do just that...the USB bit. And to confirm you have an i9100 and not the G variant.
Anwyays glad it worked out fine mate. Sorry I couldn't be of much help. Good to hear you're sorted now. Enjoy the ICS/ JB goodness.
Cheers
Edit.Do remember to make all the necessary backups though. EFS, Nand et al.
Sent from my GT-I9100 using xda app-developers app
Hey All,
I definitely hard bricked my phone, I've tried everything on XDA, every Odin, every stock and rooted rom in combination with different Pit's, baselines etc.. etc..
Not sure if I am rooted anymore or unrooted since I have installed so many Rom's.. My screen gets stuck on Samsung Logo, I can only get into Download Mode (Odin Mode) and I am sure of that.
I started off trying to install a custom rom, things went bad, after it all went bad i realized my mistakes reading, upon reading XDA.
My question for all you wonderful people on XDA is.. what do i do now with a paper weight? Do i keep trying and Beat it till it works, or replace the motherboard? & if i replace the mobo can i simply get an AT&T Mobo on this Verizon? (I have at&t, its an unlocked Verizon phone).. & where do I go to do it? (cheapest place please, totally not rich)
more info:
can't partition in odin/ i always encounter some sort of error in the middle of trying to do anything with odin.. I am only successful when i install the 66root file, and if I select the 'T Flash' option in odin it sometimes works with other roms.. but no matter what I still get stuck on the Logo Screen
list of what i have tried:
http://galaxynote2root.com/galaxy-n...o-install-custom-rom-on-rooted-galaxy-note-2/
http://www.androidayos.com/2013/04/...-note-2-sch-i605-original-firmware-stock-rom/
http://forum.xda-developers.com/showthread.php?p=39299305
http://forum.xda-developers.com/showthread.php?t=2118348
http://forum.xda-developers.com/showthread.php?t=2024207
& MUCH MORE.
I know i am dumb for how I went about doing all this so please keep it informational... thank you all!!
gnit0 said:
Hey All,
I definitely hard bricked my phone, I've tried everything on XDA, every Odin, every stock and rooted rom in combination with different Pit's, baselines etc.. etc..
Not sure if I am rooted anymore or unrooted since I have installed so many Rom's.. My screen gets stuck on Samsung Logo, I can only get into Download Mode (Odin Mode) and I am sure of that.
I started off trying to install a custom rom, things went bad, after it all went bad i realized my mistakes reading, upon reading XDA.
My question for all you wonderful people on XDA is.. what do i do now with a paper weight? Do i keep trying and Beat it till it works, or replace the motherboard? & if i replace the mobo can i simply get an AT&T Mobo on this Verizon? (I have at&t, its an unlocked Verizon phone).. & where do I go to do it? (cheapest place please, totally not rich)
more info:
can't partition in odin/ i always encounter some sort of error in the middle of trying to do anything with odin.. I am only successful when i install the 66root file, and if I select the 'T Flash' option in odin it sometimes works with other roms.. but no matter what I still get stuck on the Logo Screen
list of what i have tried:
http://galaxynote2root.com/galaxy-n...o-install-custom-rom-on-rooted-galaxy-note-2/
http://www.androidayos.com/2013/04/...-note-2-sch-i605-original-firmware-stock-rom/
http://forum.xda-developers.com/showthread.php?p=39299305
http://forum.xda-developers.com/showthread.php?t=2118348
http://forum.xda-developers.com/showthread.php?t=2024207
& MUCH MORE.
I know i am dumb for how I went about doing all this so please keep it informational... thank you all!!
Click to expand...
Click to collapse
If you can still access Download Mode then you arent truly hard bricked.
If you havent tried it you need to try flashing the PIT file. There is also the "alternative recovery method" that you should try. I think flashing the PIT file, which I believe is in one of Adams casual posts, will get you back on track but I might be wrong. Hopefully someone else will stroll through and be abke to give you a bit more help than me.
As for the first 2 urls, NEVER EVER EVER use root methods that are not on XDA. Not many people have experience with them and they could be potentially dangerous.
You also need to specify exactly what all you have tried out of those threads instead of just linking the thread.
Sent from my SCH-I605 using XDA Premium HD app
Alternative Retry
shangrila500 said:
If you can still access Download Mode then you arent truly hard bricked.
If you havent tried it you need to try flashing the PIT file. There is also the "alternative recovery method" that you should try. I think flashing the PIT file, which I believe is in one of Adams casual posts, will get you back on track but I might be wrong. Hopefully someone else will stroll through and be abke to give you a bit more help than me.
As for the first 2 urls, NEVER EVER EVER use root methods that are not on XDA. Not many people have experience with them and they could be potentially dangerous.
You also need to specify exactly what all you have tried out of those threads instead of just linking the thread.
Sent from my SCH-I605 using XDA Premium HD app
Click to expand...
Click to collapse
I have tried the alternative recovery method, but i went ahead and tried again. Stuck at "Get PIT for mapping.."
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I605_VRALJB_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
USB
gnit0 said:
I have tried the alternative recovery method, but i went ahead and tried again. Stuck at "Get PIT for mapping.."
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I605_VRALJB_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
Click to expand...
Click to collapse
I've tried different USB Ports, Chords and Machines (win 7 64bit, win 7 32bit & XP)
gnit0 said:
I have tried the alternative recovery method, but i went ahead and tried again. Stuck at "Get PIT for mapping.."
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I605_VRALJB_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
Click to expand...
Click to collapse
I had this problem.
And I just used another computer and it worked fine.
Sent from my SCH-I605 using xda app-developers app
barrackOBAMA said:
I had this problem.
And I just used another computer and it worked fine.
Sent from my SCH-I605 using xda app-developers app
Click to expand...
Click to collapse
If the PIT and alternate recovery method don't work or wouldn't hurt to try it on a different computer as barrackOBAMA suggests. If that doesn't work we can always try something else. The most important thing is to stay calm. These phones are incredibly hard to hard brick, and as long as you can get into Download Mode it can usually be fixed. It might be a long process but it'll be free where if you bought a motherboard it would cost you more money.
Sent from my SCH-I605 using XDA Premium HD app
shangrila500 said:
If the PIT and alternate recovery method don't work or wouldn't hurt to try it on a different computer as barrackOBAMA suggests. If that doesn't work we can always try something else. The most important thing is to stay calm. These phones are incredibly hard to hard brick, and as long as you can get into Download Mode it can usually be fixed. It might be a long process but it'll be free where if you bought a motherboard it would cost you more money.
Sent from my SCH-I605 using XDA Premium HD app
Click to expand...
Click to collapse
thanks guys, I really do appreciate the help and I have no problem testing any method thrown my way, if you guys were to tell me to throw it at a pigeon, I probably would do it. I have tried on 3 different VM's.. not sure if thats really considered a "different machine" or not.. I am in the middle of restoring my old dell laptop to try it on that.
shangrila500 said:
If the PIT and alternate recovery method don't work or wouldn't hurt to try it on a different computer as barrackOBAMA suggests. If that doesn't work we can always try something else. The most important thing is to stay calm. These phones are incredibly hard to hard brick, and as long as you can get into Download Mode it can usually be fixed. It might be a long process but it'll be free where if you bought a motherboard it would cost you more money.
Sent from my SCH-I605 using XDA Premium HD app
Click to expand...
Click to collapse
ah dude.. tried it on a different PC and still stuck on this motherless error <ID:0/004> Get PIT for mapping..
Honestly think I did something to the emmc or whatever it is. I don't know if I'm violating TOS but I will donate 50 bux to whomever can help. If saying I will donate is a violation please forgive.
gnit0 said:
Honestly think I did something to the emmc or whatever it is. I don't know if I'm violating TOS but I will donate 50 bux to whomever can help. If saying I will donate is a violation please forgive.
Click to expand...
Click to collapse
Lemme ask you this, do you have Kies installed? My friend had the same issue with his N2 where it would freeze in Odin and do nothing else at all after it said getting PIT for mapping. He finally had to bring it over to me and use my computer to root it, his is the AT&T version, and even though he had Kies installed he couldn't get the phone to connect right. He finally had to install Kies and all the drivers and them reinstall Kies first then the standalone drivers that were linked and after that everything worked. That may be worth a shot. I also know a lot of people have issues using VM machines and Windows 8, it seems everything works smoothest on Windows 7.
As for boring the emmc, you may have but like I said earlier it's really hard to screw this phone up so I really think it is just an issue with VM ware or possibly you haven't flashed the right file that it needs yet. We'll figure it out though hopefully, it will just take some trial and error.
Have you tried the alternate restore method? If not I will link it, it seems to fix a lot of people's phones when nothing else will.
Honestly I think it is something with the computers you're using and the drivers being wonky as usual.
Sent from my SCH-I605 using XDA Premium HD app
shangrila500 said:
Lemme ask you this, do you have Kies installed? My friend had the same issue with his N2 where it would freeze in Odin and do nothing else at all after it said getting PIT for mapping. He finally had to bring it over to me and use my computer to root it, his is the AT&T version, and even though he had Kies installed he couldn't get the phone to connect right. He finally had to install Kies and all the drivers and them reinstall Kies first then the standalone drivers that were linked and after that everything worked. That may be worth a shot. I also know a lot of people have issues using VM machines and Windows 8, it seems everything works smoothest on Windows 7.
As for boring the emmc, you may have but like I said earlier it's really hard to screw this phone up so I really think it is just an issue with VM ware or possibly you haven't flashed the right file that it needs yet. We'll figure it out though hopefully, it will just take some trial and error.
Have you tried the alternate restore method? If not I will link it, it seems to fix a lot of people's phones when nothing else will.
Honestly I think it is something with the computers you're using and the drivers being wonky as usual.
Sent from my SCH-I605 using XDA Premium HD app
Click to expand...
Click to collapse
Hey Shangrila, appreciate you helping me, I am going to try and completely uninstall all drivers for Samsung, uninstall kies, install drivers and test, if it doesn't work, re-install kies and drivers. I have tried to restore with and without kies, and all over again. I will try again but this time i will completely wipe all drivers and re-install note 2 drivers
May I ask what the first step that you did was that bricked it? You are stuck on the samsung logo flashing?
meat614 said:
May I ask what the first step that you did was that bricked it? You are stuck on the samsung logo flashing?
Click to expand...
Click to collapse
It started with a trade on craigslist. Traded my at&t iPhin 5 (i love you man insider) for this Verizon sch-i605 unlocked. I had no idea if it were able to accept custom roms or not, but i do know it was rooted (used supersu) i am a highly tech savvy guy but i don't know **** about android. I did a factory restore from setting, I then tried to install casual, downloaded it and ran it but it kept erroring so i then went and tried to upload a mod on sdcard and went to recovery mode wipe device and cache.. after that it stopped working. tried to install all sorts of roms, boot loaders, pits and what not. now all i get is error after error, either nand error or getting pit mapping halt. for some reason root66 is the only rom that is successfull but without pit file. and not sure what "T Flash" is on Odin, but some roms work while that is checked.
some roms i have tried:
CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW_Rev0406_low_ship_user.tar.md5
I605_VRALJB_Restore.tar.md5
cwm6-root-note2.tar
root66_VZW_stock_system.tar.md5
BootloaderBaseline2.tar.md5
TWRP2430VZW.tar.md5
gnit0 said:
Hey Shangrila, appreciate you helping me, I am going to try and completely uninstall all drivers for Samsung, uninstall kies, install drivers and test, if it doesn't work, re-install kies and drivers. I have tried to restore with and without kies, and all over again. I will try again but this time i will completely wipe all drivers and re-install note 2 drivers
Click to expand...
Click to collapse
If I can help I most definitely will. This sounds exactly like a driver issue thoug because it isnt able to communicate with the phone yo get the PIT for mapping. That was the same exact thing that happened with my friends phone on his laptop when I was setting everything up and showing him how to use Odin to root his phone, it would show up on a port and act like it would work but it would freeze every single damn time on the getting PIT for mapping part and wouldn't do anything else until I unplugged the phone and then it would say failed.
The main thing that helped him was wiping the drivers completely though and then just reinstalling Kies, I think he installed the other drivers after that but i can remember for sure, and it finally worked perfectly. I only have Kies on my laptop, I dont have the second set of drivers, but if you cant get it to work with just Kies try installing the other set and then test it again. You may even have to launch Kies for it to install the drivers correctly, it's been so long I can't remember that part either. Just install Kies first without the other set of drivers, launch Kies and make sure everything is set up with Kies, and see if that works. If not then install the 2nd set and try to use Odin again.
Also what OS are you doing all this on? If it's Windows 7 then it may take a little playing with the drivers to get it right. Also which version of Odin are you using? I cant get the newest version to work correctly on my laptop so that could also be part of it. Have you tried the alternative restore method? While I am 99% site it is the drivers it is always best to cover all bases.
Sent from my SCH-I605 using XDA Premium HD app
---------- Post added at 11:08 PM ---------- Previous post was at 11:06 PM ----------
gnit0 said:
It started with a trade on craigslist. Traded my at&t iPhin 5 (i love you man insider) for this Verizon sch-i605 unlocked. I had no idea if it were able to accept custom roms or not, but i do know it was rooted (used supersu) i am a highly tech savvy guy but i don't know **** about android. I did a factory restore from setting, I then tried to install casual, downloaded it and ran it but it kept erroring so i then went and tried to upload a mod on sdcard and went to recovery mode wipe device and cache.. after that it stopped working. tried to install all sorts of roms, boot loaders, pits and what not. now all i get is error after error, either nand error or getting pit mapping halt. for some reason root66 is the only rom that is successfull but without pit file. and not sure what "T Flash" is on Odin, but some roms work while that is checked.
some roms i have tried:
CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW_Rev0406_low_ship_user.tar.md5
I605_VRALJB_Restore.tar.md5
cwm6-root-note2.tar
root66_VZW_stock_system.tar.md5
BootloaderBaseline2.tar.md5
TWRP2430VZW.tar.md5
Click to expand...
Click to collapse
Watch what you check in Odin. You are ONLY supposed to check what is told in the guide, NONE OTHER! Thats a really good way to mess things up and make it harder to fix!
Can you boot into recovery? If so is there a nandroid you could try restoring?
Sent from my SCH-I605 using XDA Premium HD app
aug ttaham
i have been trying with these below none stop
Odin - 3.07
PDA - I605_VRALJB_Restore.tar.md5.xz
PIT - sch-i605-16gb.pit
none stop
gnit0 said:
i have been trying with these below none stop
Odin - 3.07
PDA - I605_VRALJB_Restore.tar.md5.xz
PIT - sch-i605-16gb.pit
none stop
Click to expand...
Click to collapse
What do you mean by none stop? Did you mean non stop? Or they aren't stopping? Sorry for asking, just a little late and I had a long day.
Sent from my SCH-I605 using XDA Premium HD app
shangrila500 said:
What do you mean by none stop? Did you mean non stop? Or they aren't stopping? Sorry for asking, just a little late and I had a long day.
Sent from my SCH-I605 using XDA Premium HD app
Click to expand...
Click to collapse
I meant i have been trying those none stop, ive tried to restore with those files atleast 10 times..
I tried to uninstall drivers and kies and then restoring but i got nothing, then tried with newly installed kies... and nothing as well.. arggg
still stuck on Get Pit Mapping
& no, i cannot get into recovery... just stays at the samsung gn 2 logo screen, and if i hold up button home and power, it just shuts off and on again... even if i release power button when i see the logo... stays at logo
gnit0 said:
i have been trying with these below none stop
Odin - 3.07
PDA - I605_VRALJB_Restore.tar.md5.xz
PIT - sch-i605-16gb.pit
none stop
Click to expand...
Click to collapse
Also this is the alternative method I was talking about:
http://forum.xda-developers.com/showthread.php?t=2040264
In the first post there is a link that says alternative restore, it has a different sboot so it will leave you unlocked. It works a lot when the PIT doesnt, its worth a shot. I still think its drivers but im throwing everything I can out so maybe you'll be able to use your phone, I know how it is to not have one to use until you can fix yours.
Sent from my SCH-I605 using XDA Premium HD app
---------- Post added at 11:27 PM ---------- Previous post was at 11:24 PM ----------
gnit0 said:
I meant i have been trying those none stop, ive tried to restore with those files atleast 10 times..
I tried to uninstall drivers and kies and then restoring but i got nothing, then tried with newly installed kies... and nothing as well.. arggg
still stuck on Get Pit Mapping
& no, i cannot get into recovery... just stays at the samsung gn 2 logo screen, and if i hold up button home and power, it just shuts off and on again... even if i release power button when i see the logo... stays at logo
Click to expand...
Click to collapse
What OS are you using? Are you using VMware right now? It still sounds like a driver issue, is there any chance you have a different computer with Windows 7 installed that you could try if the alternative restore method I linked a minute ago doesn't work?
Sent from my SCH-I605 using XDA Premium HD app
shangrila500 said:
Also this is the alternative method I was talking about:
http://forum.xda-developers.com/showthread.php?t=2040264
In the first post there is a link that says alternative restore, it has a different sboot so it will leave you unlocked. It works a lot when the PIT doesnt, its worth a shot. I still think its drivers but im throwing everything I can out so maybe you'll be able to use your phone, I know how it is to not have one to use until you can fix yours.
Sent from my SCH-I605 using XDA Premium HD app
Click to expand...
Click to collapse
that is the exact file i have been trying with odin 3.0.7 and the pit file.
shangrila500 said:
What OS are you using? Are you using VMware right now? It still sounds like a driver issue, is there any chance you have a different computer with Windows 7 installed that you could try if the alternative restore method I linked a minute ago doesn't work?
Sent from my SCH-I605 using XDA Premium HD app
Click to expand...
Click to collapse
I am trying on a local windows 7 64bit machine.. i have 16gb ram, amd fx 8120 8-core processor, and a ssd hybrid.. my mobo is a asus m5a97.. stopped using the VM's
I just tried to root my MI1 phone using Odin and appropriate downloads.
On flashing, got failure as below:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRUDMI1_Root_de_la_vega_jfltevzw.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.img.ext4
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Tried 2 computers with USB 2 direct connection -> same result. Can't boot, only get to "Firmware upgrad encountered an issue. Please select recovery mode in Kies & try again."
yearn2burn said:
I just tried to root my MI1 phone using Odin and appropriate downloads.
On flashing, got failure as below:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRUDMI1_Root_de_la_vega_jfltevzw.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.img.ext4
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Tried 2 computers with USB 2 direct connection -> same result. Can't boot, only get to "Firmware upgrad encountered an issue. Please select recovery mode in Kies & try again."
Click to expand...
Click to collapse
Which download did you try to flash first?
This postpost?
http://forum.xda-developers.com/showthread.php?p=41977487
Sent from my SCH-I545 using xda app-developers app
Mightycaptain said:
Which download did you try to flash first?
This postpost?
http://forum.xda-developers.com/showthread.php?p=41977487
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
rootdelavegajfltevzw
exact file in the zip is VRUDMI1_Root_de_la_vega_jfltevzw.tar.md5
You can see it in the log.
You know, it's my wife's phone. I was going to root it last night but waited. Maybe it updated from MI1 and I didn't check again. God I hope not. If that's the case, should it be fixable when the next root comes out??? Or could it be fixable now???
yearn2burn said:
rootdelavegajfltevzw
exact file in the zip is VRUDMI1_Root_de_la_vega_jfltevzw.tar.md5
You can see it in the log.
You know, it's my wife's phone. I was going to root it last night but waited. Maybe it updated from MI1 and I didn't check again. God I hope not. If that's the case, should it be fixable when the next root comes out??? Or could it be fixable now???
Click to expand...
Click to collapse
Go ahead and try the no wipe factory mi1 from the thread I posted.
If it fails you might have had a phone on mj7.
There is no data wipe for that as well. just a different thread in Android dev.
Is the phone soft bricked?
Sent from my SCH-I545 using xda app-developers app
Mightycaptain said:
Go ahead and try the no wipe factory mi1 from the thread I posted.
If it fails you might have had a phone on mj7.
There is no data wipe for that as well. just a different thread in Android dev.
Is the phone soft bricked?
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
It only will boot to the Odin mode. Trying a regular boot just gets to the error screen "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
yearn2burn said:
It only will boot to the Odin mode. Trying a regular boot just gets to the error screen "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
Click to expand...
Click to collapse
Okay. Try what I said before.
Sent from my SCH-I545 using xda app-developers app
Mightycaptain said:
Okay. Try what I said before.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
downloading MI1 now. I'll update...
yearn2burn said:
downloading MI1 now. I'll update...
Click to expand...
Click to collapse
Failed. Same error. Must have updated since yesterday???
Ughhh. Wife's gonna kill me!!!!
yearn2burn said:
Failed. Same error. Must have updated since yesterday???
Ughhh. Wife's gonna kill me!!!!
Click to expand...
Click to collapse
Any other suggestions? Just have to wait for the next version root?
yearn2burn said:
Any other suggestions? Just have to wait for the next version root?
Click to expand...
Click to collapse
I would download mj7 tar and flash in odin. Then just wait for a root method. It'll happen soon.
Sent from my SCH-I545 using xda app-developers app
stuckintheskull said:
I would download mj7 tar and flash in odin. Then just wait for a root method. It'll happen soon.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
There is a root method already out there, but some people suspect it has embedded malware, but it's not confirmed. A lot of people have used it without issue.
Crawshayi said:
There is a root method already out there, but some people suspect it has embedded malware, but it's not confirmed. A lot of people have used it without issue.
Click to expand...
Click to collapse
Yeah I've actually done it and it worked but kinda freaks me out a bit. Hopefully one of the devs around here can do it so it's trustworthy.
Sent from my SCH-I545 using xda app-developers app
stuckintheskull said:
Yeah I've actually done it and it worked but kinda freaks me out a bit. Hopefully one of the devs around here can do it so it's trustworthy.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
I don't trust it either. There are already devs working on pulling it apart to get to the bottom of it, so I'm sure we'll get an answer soon on the matter.
stuckintheskull said:
I would download mj7 tar and flash in odin. Then just wait for a root method. It'll happen soon.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
Link to the tar file? Hopefully would flash in Odin as PDA flash to save data?
Sent from my HTC6435LVW using Tapatalk
yearn2burn said:
Link to the tar file? Hopefully would flash in Odin as PDA flash to save data?
Sent from my HTC6435LVW using Tapatalk
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=47010231
Sent from my SCH-I545 using xda app-developers app
Mightycaptain said:
http://forum.xda-developers.com/showthread.php?p=47010231
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
Thanks. I'll flash it tonight. Confirmed with wife after due ear full that her phone updated just before she gave it over to me last night...
Sent from my HTC6435LVW using Tapatalk
Please read forum rules before posting
Questions and help issues go in the Q&A and Help section
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator
Back up and running with no data loss! Thanks so mucho!
Sent from my HTC6435LVW using Tapatalk
yearn2burn said:
Thanks. I'll flash it tonight. Confirmed with wife after due ear full that her phone updated just before she gave it over to me last night...
Sent from my HTC6435LVW using Tapatalk
Click to expand...
Click to collapse
this is why you always check BEFORE attempting root, no matter what even if someone tells me they didn't update their phone or their phone is running blah blah, i always double check because you can never be too safe
Crawshayi said:
There is a root method already out there, but some people suspect it has embedded malware, but it's not confirmed. A lot of people have used it without issue.
Click to expand...
Click to collapse
Is this a method separate from the one allowing you to maintain root through the MJ7 update? Is it allowing people to root after taking the update without root?
i have verizon galaxy note 2 and jailbreak bootloader and flashed DN3 rom.
and i had no time to fix wifi so i went out and came back really late..my computer was off
so i just re-search on google and i just put dn3 and went in the first one...which is for GT-N7100....
and i just scroll down without checking...click the wifi fix thread for GT-N7100..and i also scroll down without checkin..
and i follow those steps....dang alcohol make me blind.. i didnt even check the file name...after i finish that..boot it up
in front of me my VZW galaxy note2 show me "SAMSUNG GT-N7100".....
so i fricked out i try to flashed STOCK I605 rom..odin give FAIL message....tried 66root VZW stock rom...again odin give me FAIL message..
and after that on the screen.... phone- -yellow triangle with exclamation mark - - computer with Firmware upgrade encountered an issue.please select recover mode in kies & try again...
what do i have to do now..:crying::crying::crying::crying:
corean0213 said:
i have verizon galaxy note 2 and jailbreak bootloader and flashed DN3 rom.
and i had no time to fix wifi so i went out and came back really late..my computer was off
so i just re-search on google and i just put dn3 and went in the first one...which is for GT-N7100....
and i just scroll down without checking...click the wifi fix thread for GT-N7100..and i also scroll down without checkin..
and i follow those steps....dang alcohol make me blind.. i didnt even check the file name...after i finish that..boot it up
in front of me my VZW galaxy note2 show me "SAMSUNG GT-N7100".....
so i fricked out i try to flashed STOCK I605 rom..odin give FAIL message....tried 66root VZW stock rom...again odin give me FAIL message..
and after that on the screen.... phone- -yellow triangle with exclamation mark - - computer with Firmware upgrade encountered an issue.please select recover mode in kies & try again...
what do i have to do now..:crying::crying::crying::crying:
Click to expand...
Click to collapse
Where is Odin giving you a fail message after? You are still able to get into recovery? If so just flash another ROM for Verizon.. Let me know.. Don't freak out though this is not a big deal
Sent from my SCH-I605 using xda app-developers app
lacoursiere18 said:
Where is Odin giving you a fail message after? You are still able to get into recovery? If so just flash another ROM for Verizon.. Let me know.. Don't freak out though this is not a big deal
Sent from my SCH-I605 using xda app-developers app
Click to expand...
Click to collapse
i forgot to take a picture that message....and dont remember..:crying:
i can not get into recovery..only download mode...
so what i tried i extract n7100 file that i flash into my bootload and check what kind of file is in, and than i extract ROM file to get same kind of file..
and i looking around how to make .tar.md5 and done.
so i flash this file into my phone's on download mode.. i saw download gauge getting up and i thought i found out the way to fix..BUT gauge go up near to max and just stop there and does not move.. even odin dont show me any FAIL or ERROR message it just stop and im pretty sure it stop on sboot.bin section.
corean0213 said:
i forgot to take a picture that message....and dont remember..:crying:
i can not get into recovery..only download mode...
so what i tried i extract n7100 file that i flash into my bootload and check what kind of file is in, and than i extract ROM file to get same kind of file..
and i looking around how to make .tar.md5 and done.
so i flash this file into my phone's on download mode.. i saw download gauge getting up and i thought i found out the way to fix..BUT gauge go up near to max and just stop there and does not move.. even odin dont show me any FAIL or ERROR message it just stop and im pretty sure it stop on sboot.bin section.
Click to expand...
Click to collapse
You need to go to droidstyle 's thread and download a Odin file with bootloader in it..Also pit file.. flash them through Odin and you should be good
Sent from my SCH-I605 using xda app-developers app
lacoursiere18 said:
You need to go to droidstyle 's thread and download a Odin file with bootloader in it..Also pit file.. flash them through Odin and you should be good
Sent from my SCH-I605 using xda app-developers app
Click to expand...
Click to collapse
are you talking about this one?
http://forum.xda-developers.com/showthread.php?t=2043636
corean0213 said:
are you talking about this one?
http://forum.xda-developers.com/showthread.php?t=2043636
Click to expand...
Click to collapse
Negative..This would be the one:
http://forum.xda-developers.com/showthread.php?t=2024207
you probably want to use the RAMC3
lacoursiere18 said:
Negative..This would be the one:
http://forum.xda-developers.com/showthread.php?t=2024207
you probably want to use the RAMC3
Click to expand...
Click to collapse
i tried to do that with pit file.. but doesnt work wirh
these message...
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and i attached 2 picture that on my phone
if you take a look one in odin mode ( download mode )
says:
PRODUCT NAME: GT-N7100
CUSTOM BINARY DOWNLOAD : YES (9 COUNT) this number keep getting up when i flash VZW stock rom...
CURRENT BINARY : CUSTOM
SYSTEM STATUS : CUSTOM
WARRANTY BIT : 0
AND
another picture is when power on this shows and not going further...
You messed up hard core. You have to do kabols unbrick method bro or that phones a paper weight.....
Sent from my SCH-I605 using Tapatalk
http://forum.xda-developers.com/showthread.php?t=2615587 here is the link. Good luck. Your gonna need it. That resistor is so small. Your only other option other than that is a 50 dollar jtag done by mobiletech
Sent from my SCH-I605 using Tapatalk
roflcoptersoisoi said:
You messed up hard core. You have to do kabols unbrick method bro or that phones a paper weight.....
Sent from my SCH-I605 using Tapatalk
http://forum.xda-developers.com/showthread.php?t=2615587 here is the link. Good luck. Your gonna need it. That resistor is so small. Your only other option other than that is a 50 dollar jtag done by mobiletech
Sent from my SCH-I605 using Tapatalk
Click to expand...
Click to collapse
even i could enter download mode its hard brick?:crying::crying::crying::crying::crying::crying::crying:
Pretty much.
Sent from my SCH-I605 using Tapatalk
Yup you did just about the only thing possible to brick this device. Never flash a bootloader for another device.
akellar said:
Yup you did just about the only thing possible to brick this device. Never flash a bootloader for another device.
Click to expand...
Click to collapse
I would say you could send me your phone and I could do the unbrick method for you. But I would feel terrible if I messed it up. It does work though. but i also have jewlers tools and all that jazz. Get it jtagged and be done.
I say it's fixable stop giving him a heart attack...
Odin a 4.1.2 stock rom on there with a .pit
Like the one you asked about before lol
Dude the guy that made the unbricker made it cause he did the same thing... it's not fixable without jtag or unbrick
Sent from my SCH-I605 using Tapatalk
Lacoursiere18 knows his stuff well. He suggested what I thought would fix it.
Previously last week Corean0213 had similar problem and got it fixed. My apologies I didn't see/overlooked he flashed GT-N7100 firmware on a SCH-1605 this week. Thinking he still didn't do the 4.3 OTA stock firmware I thought he could re flash with Odin. But guess he made a bigger boo boo then expected with wrong device firmware. uch:
OffTheChainz said:
Lacoursiere18 knows his stuff well. He suggested what I thought would fix it.
Previously last week Corean0213 had similar problem and got it fixed. My apologies I didn't see/overlooked he flashed GT-N7100 firmware on a SCH-1605 this week. Thinking he still didn't do the 4.3 OTA stock firmware I thought he could re flash with Odin. But guess he made a bigger boo boo then expected with wrong device firmware. uch:
Click to expand...
Click to collapse
Thanks.. I think the problem might be if that bootloader he flashed is locked down.. If it is then I don't think odin can write over it..
I wouldn't say jtag would not work. Best thing to do is call Josh over at mobile tech videos and he'll let you know..He is reasonable and a nice guy, he won't steer you wrong..
Sent from my SCH-I605 using xda app-developers app
Jtag will work. They would have to do the downgrade method where they remove the emmc Chip and flash it. Then proceed as normal
Sent from my RM-915_nam_usa_228 using Tapatalk
I shouldn't even of bothered but flashed a bootloader that was linked to me. Apparently the wrong one it's a n7100 and I have a i605. I've been told it's not locked and posted several times in the DN3 thread. What can I do?
thechaoz said:
I shouldn't even of bothered but flashed a bootloader that was linked to me. Apparently the wrong one it's a n7100 and I have a i605. I've been told it's not locked and posted several times in the DN3 thread. What can I do?
Click to expand...
Click to collapse
Your answer can be found in the 8th post of this thread.
Sent from my SCH-I605 using XDA Premium 4 mobile app