i am flashing CM9 Resurrection Edition for use with Odin:
20120420: Download
this method Download CM9 Resurrection Edition
- Download GApps and put it onto your internal sdcard
- Open Odin
- Choose cm-9-XXXXXXXX-ODIN-galaxys2.tar.md5 as PDA
- Boot your phone into download mode
- Connect your device via usb to your computer
- Wait till Odin has fully recognized your phone
- Hit the start button and wait till the flash process is finished
but now odin id stuck at
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cm-9-20120420-ODIN-galaxys2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004> NAND Write Start!!
<ID:0/004> Sbl.bin
<ID:0/004> param.lfs
<ID:0/004> modem.bin
<ID:0/004> factoryfs.img
<ID:0/004> data.img
what should do unplud close odin what
its about 15 mins
what i do any body i am freaking out
Related
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLPU_I9100XXLQ6_I9100XEZLP3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img
While Flashing Latest Stock ODIN getting stuck again and again on same MSG "cache.img" any solution ????
IAmRizzler said:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLPU_I9100XXLQ6_I9100XEZLP3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img
While Flashing Latest Stock ODIN getting stuck again and again on same MSG "cache.img" any solution ????
Click to expand...
Click to collapse
If you did NOT check repartition and did NOT select a .pit file then you are safe. Then you can just try again. Or try again with a different rom and/or a different USB cable.
Sounds like the tar file you downloaded might be corrupt. Try downloading it again, and once you've done so/unpacked the tar, use 7Zip to test the integrity of the archive. If it comes up all files OK/no errors then that isn't your problem.
Getting this so far
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I9300XXEMG4_I9300OXAEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img
Should I pull the cable or what? Very confused.
It's just stuck there and the blue thing is no longer moving on the device.
Probable bad firmware file .
Skander1998 said:
Getting this so far
Code:
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
KIES_HOME_I9300XXEMG4_I9300OXAEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:4)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
boot.img
NAND Write Start!!
recovery.img
system.img
Should I pull the cable or what? Very confused.
It's just stuck there and the blue thing is no longer moving on the device.
Click to expand...
Click to collapse
Happen to me long time ago when flashing another region firmware...what I do I just pull out the battery and re-enter again download mode...when it stuck just pull out the battery and flash again until it show pass...
danierakes said:
Happen to me long time ago when flashing another region firmware...what I do I just pull out the battery and re-enter again download mode...when it stuck just pull out the battery and flash again until u success...
Click to expand...
Click to collapse
That worked.
Solved.
hi i'm using sprint galaxy mega(sph-l600)
but my phone is brick ...
and unable to flash with odin.
so, plz share to me sph-l600 pit file??
have a good today.
========================= modify my situation ===========================
My situation is soft brick. and do not working to flashing with odin.
always fail to flash System.img.ext4.. I've tried change usb port and usb cable. but fail..
So, I'm gonna try flash with PIT file. but I don't have SPH-L600 PIT file....
attacted my situation.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L600VPUAMK1_L600SPTAMK1_L600VPUAMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Ext4)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
raor said:
hi i'm using sprint galaxy mega(sph-l600)
but my phone is brick ...
and unable to flash with odin.
so, plz share to me sph-l600 pit file??
have a good today.
Click to expand...
Click to collapse
Hi..i don't have this model but to flash a pit file you need odin to flash it as the phone has to be in download mode also and if the phone cannot be put into this mode then flashing cannot be done, if it is a hard brick (hardware related) then the phone will require a jtag service to repair it. does the phone still come on to the mega screen?
Thank you for quick reply
starmaster10 said:
Hi..i don't have this model but to flash a pit file you need odin to flash it as the phone has to be in download mode also and if the phone cannot be put into this mode then flashing cannot be done, if it is a hard brick (hardware related) then the phone will require a jtag service to repair it. does the phone still come on to the mega screen?
Click to expand...
Click to collapse
Thank you for quick reply. but my situation is soft brick. and do not working to flashing with odin.
always fail to flash System.img.ext4.. I've tried change usb port and usb cable. but fail..
So, I'm gonna try flash with PIT file. but I don't have SPH-L600 PIT file....
attacted my situation.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L600VPUAMK1_L600SPTAMK1_L600VPUAMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Ext4)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hi everyone!
Hope you can help with this.
I have a Verizon Galaxy S4 with a completely dead (black) screen. It's not just cracked... i can't see anything.
I can connect it to my computer and see my files, so i know it's still alive, but i want to wipe it and sell it for parts, since the logic board and other stuff is still good.
This phone is NOT rooted.
I can't put it in debug mode because i can't see anything on the screen.
When i try to flash it with Odin, following the instructions for flashing to stock, i get the following:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've tried three or four times with the same results.
Any ideas what's going wrong?
I would prefer to reset to stock, but maybe i should just delete photos / contacts manually?
Thanks in advance for your help!
MaliaSleight said:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Persistence pays off... i read a bunch of other posts about general Odin issues, and though i didn't find anything 100% the same as my issue, the theme was to try a different version of Odin and a different TAR. I did both and now i get PASSED!
Hi
i updated my S III with stock firmware with 4.3 (I9300XXUGNB6_I9300OJVGNB3_I9300XXUGNA8_HOME.tar.md5) via Odin. It was successful and worked fine for a few days, but after 3 or 4 days my phone get stucked on Samsung logo screen, i tried wiping data and cache from recovery, but problem is same. So i am trying to re flash my phone with same stock rom. But i am not able to do it.
I am using Odin 3.07,
Here is the Log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNB6_I9300OJVGNB3_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
I also used to Root it with cf auto root,
Here is the Log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-m0-m0xx-gti9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Tried using different USB ports and USB cables?
audit13 said:
Tried using different USB ports and USB cables?
Click to expand...
Click to collapse
Yes Tried, Recently my S III was updated via same port and USB Cable,
Have you tried flashing the stock ROM with a pit file?
It's also possible that the internal memory chip is damaged.
audit13 said:
Have you tried flashing the stock ROM with a pit file?
It's also possible that the internal memory chip is damaged.
Click to expand...
Click to collapse
Yes I tried, Here is result:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNB6_I9300OJVGNB3_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
Stuck on Get PIT for mapping,
Since it is stuck on the pit file, this leads me to believe that the cable is not compatible or the internal memory is damaged.
I have flashed many different Samsung phones over several years and I find that USB cables can cause the flash to fail when Odin is trying to read the partition information (PIT), flash a bootloader, or flash the system image.