Hey everyone.
The digitizer on my phone has started to act funky recently and I've decided to get a new one, but I'd like to know a couple of things first:
1. Is the digitizer integrated into the glass on the screen or is it a separate part? I see most places selling what seems like both but I've also seen different items labeled as digitizers and I'd like to be certain.
2. What tools will I need to install it? I'm seeing that I need 2mm double sided tape and a T5 torx screwdriver but I'd like to know if I need anything else.
2. Will the screen have to be recalibrated once the digitizer is installed?
3. What's a good site to buy a replacement? I'm willing to pay for an expensive screen if it's a good quality that'll hopefully last for another couple of years.
Thanks!
monorail0 said:
Hey everyone.
The digitizer on my phone has started to act funky recently and I've decided to get a new one, but I'd like to know a couple of things first:
1. Is the digitizer integrated into the glass on the screen or is it a separate part? I see most places selling what seems like both but I've also seen different items labeled as digitizers and I'd like to be certain.
2. What tools will I need to install it? I'm seeing that I need 2mm double sided tape and a T5 torx screwdriver but I'd like to know if I need anything else.
2. Will the screen have to be recalibrated once the digitizer is installed?
3. What's a good site to buy a replacement? I'm willing to pay for an expensive screen if it's a good quality that'll hopefully last for another couple of years.
Thanks!
Click to expand...
Click to collapse
Hey look, on august i bricked my screen, and needed a replacement, well i bought a new digitizer + screen at ebay, and i lost $120 money because a bad screen quality, touch not 100% functionally...
but i send my cellphone to support, than we billed me $150 and a better screen original... i think... dont needed to recalibrate, but i use a Aroma based ROM to calibrate it...
i didnt know how to change it by yourself :/
monorail0 said:
Hey everyone.
The digitizer on my phone has started to act funky recently and I've decided to get a new one, but I'd like to know a couple of things first:
1. Is the digitizer integrated into the glass on the screen or is it a separate part? I see most places selling what seems like both but I've also seen different items labeled as digitizers and I'd like to be certain.
2. What tools will I need to install it? I'm seeing that I need 2mm double sided tape and a T5 torx screwdriver but I'd like to know if I need anything else.
2. Will the screen have to be recalibrated once the digitizer is installed?
3. What's a good site to buy a replacement? I'm willing to pay for an expensive screen if it's a good quality that'll hopefully last for another couple of years.
Thanks!
Click to expand...
Click to collapse
Dunno what's that you found, but the digitizer and the glass are inseparable and must always come together. You CAN however get just the glass or the glass with the frame. I'd get the frame too if I were you. Saves you needing the double-sided tape.
If you get it with the frame included, then just the TORX and maybe some plastic prying tool (a guitar pick will do nicely). Probably a pair of tweezers too.
No recalibration necessary or even available.
Amazon or eBay (can't remember which) reportedly has decent ones. Look for the merchant "seller1on1" (again, not sure if that's correct). There is also a link to another decent site in another thread. Guess you need to do a little searching around the forum.
Velcis Ribeiro said:
dont needed to recalibrate, but i use a Aroma based ROM to calibrate it...
i didnt know how to change it by yourself :/
Click to expand...
Click to collapse
Aroma calibration is for Aroma ONLY, it has nothing to do with any other part of the system.
I'll hop on the topic. I've got the spare digitizer and I need to replace it. Can anyone give me some tips to dissasemble & install? i've been looking for videos but i need real tips from anybody who did it already.
Thanks!
ravilov said:
Dunno what's that you found, but the digitizer and the glass are inseparable and must always come together. You CAN however get just the glass or the glass with the frame. I'd get the frame too if I were you. Saves you needing the double-sided tape.
If you get it with the frame included, then just the TORX and maybe some plastic prying tool (a guitar pick will do nicely). Probably a pair of tweezers too.
No recalibration necessary or even available.
Amazon or eBay (can't remember which) reportedly has decent ones. Look for the merchant "seller1on1" (again, not sure if that's correct). There is also a link to another decent site in another thread. Guess you need to do a little searching around the forum.
Aroma calibration is for Aroma ONLY, it has nothing to do with any other part of the system.
Click to expand...
Click to collapse
Awesome, thanks. Apparently though Seller1on1 sells low quality screens, at least according to the reviews on the amazon page. amazon(dot)com/Motorola-Screen-Digitizer-Replace-broken/product-reviews/B004Z0UO8O/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 I'll look for that other thread though.
ravilov said:
Dunno what's that you found, but the digitizer and the glass are inseparable and must always come together. You CAN however get just the glass or the glass with the frame. I'd get the frame too if I were you. Saves you needing the double-sided tape.
If you get it with the frame included, then just the TORX and maybe some plastic prying tool (a guitar pick will do nicely). Probably a pair of tweezers too.
No recalibration necessary or even available.
Amazon or eBay (can't remember which) reportedly has decent ones. Look for the merchant "seller1on1" (again, not sure if that's correct). There is also a link to another decent site in another thread. Guess you need to do a little searching around the forum.
Click to expand...
Click to collapse
Don't listen to anyone who says that the LCD and digitizer are inseparable. They are. You can buy an OEM digitizer and replace it alone (if your LCD is fine. Trust me, I would know. I just did it myself.
Look at the teardown and screen sections on this page for detailed step by step instructions on how to do this.
http://www.ifixit.com/Device/Motorola_Atrix_4G
Vigneshd said:
Don't listen to anyone who says that the LCD and digitizer are inseparable. They are. You can buy an OEM digitizer and replace it alone (if your LCD is fine. Trust me, I would know. I just did it myself.
Look at the teardown and screen sections on this page for detailed step by step instructions on how to do this.
Click to expand...
Click to collapse
in eariler post no one mentioned the LCD screen.... ravilov said glass ans digitizer.
jhonnyx said:
in eariler post no one mentioned the LCD screen.... ravilov said glass ans digitizer.
Click to expand...
Click to collapse
My apologies. But in most cases, when one refers to the digitizer, they refer to the glass on top of the LCD ... no?
Vigneshd said:
My apologies. But in most cases, when one refers to the digitizer, they refer to the glass on top of the LCD ... no?
Click to expand...
Click to collapse
No prob at all pal!. The digitizer and the glass are "the digitizer", where the digitizer is a film located in the rear of the glass (correct me please if im wrong)
Vigneshd said:
My apologies. But in most cases, when one refers to the digitizer, they refer to the glass on top of the LCD ... no?
Click to expand...
Click to collapse
Yes, and that's exactly what I said. Glass + digitizer. Inseparable. No one ever mentioned the LCD.
for install instruction go to ifixit.com
Sent from my MB860 using xda app-developers app
Related
How does one go about removing them? I've done a google and XDA-Forums search and found that there are numerous answers all seemingly discounted by any number of people:
toothpaste, no good for capacitive screens
Displex sure, THEY say it's good for the TP2, but so many people say not
So, anyone have any ideas.
And, yes, I know, screenguards are great and the holy grail. I don't have one. So, please, I know I am asking for a cause that I probably could have prevented, but every time I put a screenguard on my device, it was much too mushy and I tried a lot of them.
Thanks in advance.
I would also like to know how to remove the scratches on the screen. The screen guards make the touch screen less sensative. Theres got to be some type of wax or something.
I've used the screen guard that came with my TP2 since day one. My screen is still pretty darn sensitive....
I have skinomi on my tp2 and although it takes alot of patience to put it works flawlessly...ive tried scratching it with keys and the thing just wont scratch!! its awesome..its a bit on the expensive side if you get the entire skin for the phone like i did but its worth the money in my opinion.
go to skinomi.com
I guess T-Cut might work, i used it on my dads samsung and it cleared up the screen some.
When i was a kid we used to wear swatch watches which always got scratched up, we used to use Duraglit made by Brasso which is a metal polish wadding...kinda like cotton wool with a light abrasive in it, which worked wonders!
Something with very light abrasive properties(like toothpaste) should do it but watch out for any solvents and chemicals in the product that may react with or even MELT the plastic!!!!!
most things like T-Cut scratch remover just take a lot of time and patience.
I anything works for you re-post and let us know!
Actually Displex tells you not to use its product on resistive touch-screens.
Anyway, I just ordered iDrops about a week ago and have been trying it for the last day with no results, at all. I've tried variable amounts of pressure, dozens of applications as the instructions say and I've only hurt my phone. All it does it put a strange texture on your phone that makes it grainy and more susceptible to scratches. Even my stylus scratches the phone, now! I had to use a wet cloth to get the graininess away.
My recommendation is not to bother with iDrops. It seems to not work for the TP2.
Hmm, its just an idea but I've been repairing my windscreen today using special resin that cures in direct sunlight. I must say it works pretty well, it's hard to notice the repair. I would try t-cut or other mild abbrasive to get rid of light scratches and fill really bad ones with that resin. Next comes a good screen protector to hide any imperfections.
thanks, but WHAT website
spammmer said:
if your touch screen is very scratch or broken, you can just buy the new touch screen and then replace it, it is easy to do. I also has instruction. you can visit my website.
thanks
Click to expand...
Click to collapse
I see your post, yet, I have no idea what website to which you refer. Nevermind, didn't realize it was in your header.
Why do you not send instructions with the order? IF you're selling replacement parts why then must a customer have to contact you for replacement instructions?
He is just advertising himself. Just find the best price on buy it, you can find the HTC service manual on google.
Not disputing that fact
petard said:
He is just advertising himself. Just find the best price on buy it, you can find the HTC service manual on google.
Click to expand...
Click to collapse
Just questioning that if they sell the parts, why must the instructions be emailed separately?
Bumping because I need the same thing resolved...
Questions:
1) Anyone know a good, semi-reputable site to replace the front screen.
2) Is the front plastic considered part of the LCD Screen, or do they come apart separate? (The scratch on my phone is purely on the outer-most section of the screen, with no damage to the image display) -- I ask as some phones i've seen have an "LCD Display" followed by a "Cover Screen")
3) Regardless of #2's answer, what am I looking to buy (The technical/semi-technical name)? Closest I've seen is LCD Digitizer, but I'm not sure if i need that component or the LCD Screen.... cover.... portion..
Unfortunately the part i saw was $124, and I happen to have insurance on the phone if it does indeed get that expensive, but I just hope the parts are separate ;-)
Thanks,
-Lee
BBM-Lee said:
Bumping because I need the same thing resolved...
Questions:
1) Anyone know a good, semi-reputable site to replace the front screen.
2) Is the front plastic considered part of the LCD Screen, or do they come apart separate? (The scratch on my phone is purely on the outer-most section of the screen, with no damage to the image display) -- I ask as some phones i've seen have an "LCD Display" followed by a "Cover Screen")
3) Regardless of #2's answer, what am I looking to buy (The technical/semi-technical name)? Closest I've seen is LCD Digitizer, but I'm not sure if i need that component or the LCD Screen.... cover.... portion..
Unfortunately the part i saw was $124, and I happen to have insurance on the phone if it does indeed get that expensive, but I just hope the parts are separate ;-)
Thanks,
-Lee
Click to expand...
Click to collapse
I am nearly positive you do not need to replace the LCD. You only need a new digitizer (that is the name of the layer that recognizes touch) which you can find for around $25 online!
petard said:
I am nearly positive you do not need to replace the LCD. You only need a new digitizer (that is the name of the layer that recognizes touch) which you can find for around $25 online!
Click to expand...
Click to collapse
Correct me if I'm wrong but changing this digitizer would void warranty if I were to change it myself ? ?
Go to At&t and see if they will replace it for you if you buy the digitizer. If not ask At&t or find a reputable place that does, ive seen for around $50 which was suggested to me by at&t. It's worth the money trust me! When I had my old LG Incite, I tried replacing the digitizer because my screen was scratched and ended up breaking the lock and camera buttons as well as the touch screen. Since then every phone i've had gets a case and screen protector from the day I lay eyes on it. If the case and screen protector are their after I get my phone I wont use it till their on. Scratches just annoy me but I guess i'm just odd lol.
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
keithgrobertson said:
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
Click to expand...
Click to collapse
Try this http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/1
Or, this http://www.youtube.com/watch?v=TbR56jSplRs
Broke my digitizer and did the job myself using the youtube guide above. Just used straight up superglue to glue digitizer to frame. I put a bunch on the top and bottom and very little on the sides.
Amazingly the phone worked when i put it back together... for a while until I screwed up one of the ribbons by opening it a bunch more times. Be extra careful with these, especially the volume/camera ribbon. You can bend it pretty easily trying to slide it back into its slot.
Good luck.
NB: Theres places that will do it for as little as $90 in case you don't want to take the risk.
http://www.ubreakifix.com/
Thanks for posting the youtube link. I can't even quote the post because it involves an external link. The video was vague on details and the quality is crap but it did the trick.
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from amazon and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Metacat said:
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from ebay and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Click to expand...
Click to collapse
I replaced my digitizer, and had the EXACT same thing happen (not the light sensor but the line in the screen that doesnt respond to touch).
Get a new digitizer, but get it from someone else.
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Metacat said:
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Click to expand...
Click to collapse
No. I sold it and let someone else deal with it. Didn't have the time to replace the digitizer again. Too much of a hassle.
I just replaced a digitizer on an atrix... i didnt put any adhesive on it because there was what i thought was adhesive strips on the digitizer... but there's strips on the screen that doesnt respond, i heated it n tried reattaching the digitizer a few times n sometimes the home and back button will work, sometimes they wont... any suggestions? could the lack of adhesive cause this?
Menu buttons problem
if menu buttons is freeze till I block and then unblock my phone is it digitizer problem ?
what do you mean by " block/unblock" ?
Sent from my HTC Desire CDMA using XDA
He means lock/unlock.
Go the ifixit route!
Just went through 3 digitizers in my repair, and wanted to share my experience/caveats
I bought one digitizer from All4Cellular for $25, and the others with a 20% discount a few days later, for $20.
I installed
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Got the idea to move the LCD screen from another RepairUniverse YouTube video and a previous post here, and tried installing the digitizer from the front face of the phone. It was still a delicate matter to bend the flex cable so that it fit through the slot, and then re-position the LCD and align the sticky strips of the digitizer on the LCD and casing. Part of the digitizer worked this time - a 1cm vertical strip on the left fowled any attempt to touch icons or use a keyboard, so I thought I had damaged things again (doh!).
Hoping third time was the charm, I completely disassembled the phone using the guide in the 'ifixit' link, since a digitizer/case assembly was suggested in another thread. The rear camera just needs to be raised above the casing so the thin plate can move upward, and the LCD pops out easily if the sides of the casing are delicately pulled. The digitizer can be positioned easily and with minimal bending/twisting of the flex cables.
When reconnecting everything the third time, I noticed that pressing down on the front camera / digitizer connection *with the rubber boot in place* didn't pass when pulling the connected assembly upward. So I pulled the rubber boot out of the way and snapped the camera / digitizer connection firmly, then re-inserted the boot. A loose connection might have been the culprit for the nonfunctioning part of the digitizer in the second test.
@MrSaba - I had the same issue with capacitive buttons - perhaps because the screen senses touch and disables those buttons. Replacing the digitizer solved the issue
trouble
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
drZeT said:
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
Click to expand...
Click to collapse
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
jjwatmyself said:
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
Click to expand...
Click to collapse
The first one was with the red stripe indeed, from china. The one with a frame came from UK, "used but tested OK". original screen is gone - tore off flex cable while removing.
Well, update...
2 screens bought on eBay were BAD. Had to wait full month for authorised motorola service to change the digitizer. Must say though that both merchants on ebay refunded, no questions asked. Lessons learned - pay more, wait longer, never give up
DrJCFitz said:
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Click to expand...
Click to collapse
What I noticed on their video was that their folded digitizer connector magically unseats itself during the disassembly transition. I had to pry mine off based purely on guesswork and think I might have broken the flip-chip that is stuck onto the frame with double-sided tape. Like yours, my touchscreen doesn't respond at all, despite there being no cable tears. I'm going to try and re-heat that flip chip and maybe get the connections to work again (doubtful).
To anyone else out there attempting this... when you go to remove the touchscreen, HEAT THE CONNECTOR so that you can gently pry it out!
Bad screen I got 3 before it worked its fine now if old one partially works new one doesn't screen is junk took mine apart several times to figure out screens were junk...guess they felt sorry for me give me my money back plus free working screen.from amazon
Also that lock clamp u mentioned first video I watched didn't show unlocking that I just pulled it out and pushed back in it was the 2 screen that I figured out it needed to be pryed loose by the white clamp but guess I didn't damage it..
Sent from my HTC One X+ using xda premium
I have just put in my second digitiser. The first was one had a red stripe, which was junk, the second on I bought had the plastic round the edge and the digitiser.
I put it in and it worked fine no dead spots at all. Then 12 hours in it started to stop working intermittently. Then 24 hours after that while on charge its dead again. I reflashed notattrix and still nothing. I've confirmed all the ribbon connectors are firmly in place and everything looks right.
Any ideas whats wrong?
thanks
Jonnym
So... my TouchPad was dropped and the screen broke.
The device works perfect (even the touchscreen), but the screen is broken. Is that JUST the digitizer? Is that what I need to replace? I'm trying to find out if I can if this.
Would this work (linked below)? Or is that just the piece beneath the glass? Not sure exactly.
http://www.repairsuniverse.com/hp-touchpad-touch-screen-digitizer-replacement.html
OR
http://www.ebay.com/itm/US-HP-Touch...ens-Screen-Parts-Repair-Fix-OEM-/230707927573
wasnt said:
So... my TouchPad was dropped and the screen broke.
The device works perfect (even the touchscreen), but the screen is broken. Is that JUST the digitizer? Is that what I need to replace? I'm trying to find out if I can if this.
Would this work (linked below)? Or is that just the piece beneath the glass? Not sure exactly.
http://www.repairsuniverse.com/hp-touchpad-touch-screen-digitizer-replacement.html
OR
http://www.ebay.com/itm/US-HP-Touch...ens-Screen-Parts-Repair-Fix-OEM-/230707927573
Click to expand...
Click to collapse
Define broken. If you mean the top layer is broken ( cracks that you can feel by running your finger over them, which may or may not cause issues with touchscreen sensitivity ) then yeah, the digitizer is all you need. pretty easy to swap out, too. And, as you can see, they are usually between 25-30 bucks on ebay.
If it looks like the bottom layer is cracked, then you may have broken the LCD. I can't imagine that being the case, but wanted to make you aware of the possibility. you can get the LCD for about $60 on ebay.
Edit:If you need a good solid walkthrough for opening up your touchpad, check out ifixit.com
jka3588 said:
Define broken. If you mean the top layer is broken ( cracks that you can feel by running your finger over them, which may or may not cause issues with touchscreen sensitivity ) then yeah, the digitizer is all you need. pretty easy to swap out, too. And, as you can see, they are usually between 25-30 bucks on ebay.
If it looks like the bottom layer is cracked, then you may have broken the LCD. I can't imagine that being the case, but wanted to make you aware of the possibility. you can get the LCD for about $60 on ebay.
Edit:If you need a good solid walkthrough for opening up your touchpad, check out ifixit.com
Click to expand...
Click to collapse
+1
IFixit now has an Android app in the market with complete instructions!
A friend of mine has an ATT Titan (phone says PI39100) with a cracked front glass. I was looking to purchase a new front lens/digitizer for her phone and do the replacement. Most of what I find online are for the x310e.
Long question short: is the front lens for the x310e the same exact one as for the PI39100? or are the two not compatible?
Also, if someone can point to a DIY for doing this I'd appreciate it - otherwise, i'll take on it the same as the Galaxy Tab 10.1 I did earlier this week (using a hair dryer and an exacto knife) I would like to at least know the lens is the same so I can order soon.
Thanks in advance.
The screens are the same. The only difference will be that the new screen will have the HTC-Brand name instead of AT&T. Is it just the glass cover that's broken or is the whole touch screen? You can either replace just the glass cover or the entire touch screen. At least that is what I understand because I've seen both parts offered separately.
Regarding the DIY replacement have a look here:
http://forum.xda-developers.com/showthread.php?t=1569714
Hope this helps.
malvo26 said:
The screens are the same. The only difference will be that the new screen will have the HTC-Brand name instead of AT&T. Is it just the glass cover that's broken or is the whole touch screen? You can either replace just the glass cover or the entire touch screen. At least that is what I understand because I've seen both parts offered separately.
Regarding the DIY replacement have a look here:
http://forum.xda-developers.com/showthread.php?t=1569714
Hope this helps.
Click to expand...
Click to collapse
Excellent. This is EXACTLY what I was looking for. Thank you VERY much for your assistance
Oh, and it's the glass cover that's broken, because she's still able to (and currently continues to) use the phone. On ebay, I've seen the glass and digitizer going for under $30 shipped, so I think it's reasonable enough.
Thanks again. :good:
Glad to help. That's we are all here for: help each other.
Okay, so my Terminator...errr, my son, managed to crack the heck out of his Nabi 2 digitizer screen. The LCD screen is fine and he can still use the Nabi, but I've noticed more and more cracks so I'm sure it's bound to break the LCD.
So, I went on eBay and ordered a piece of glass, but I'm not thinking it's not going to work. It was only like 13 bucks. I had a model number given to me after the fact (at070tn90), and I just looked and I didn't get that one. I'm just hoping it will work.
At any rate, I finally got the Nabi apart, but I've been fearful of removing the connectors for the screen. Can someone PLEASE tell me how to get the screen apart so I can try to replace it when I get the correct glass for it? PLEASE! There are NO Youtube vids for this...tons for the Nexus 7, but nada for Nabi.
Please help...I'm desperate! Thanks so much!!
The likelihood the digitizer isn't cracked is very low.
NABI2 touchscreen layering:
front glass..............thick (glue around outer most edges to frame)
airgap......................very thin (glue around edges)
digitizer glass........thin
lcd............................thick
I tried the same thing but the actual digitizer glass is like 1/10 the thickness of the front panel glass and glued to it on the edges. If the digitizer glass is not cracked, it will probably crack on attempted removal from the front panel. If the digitizer is fully working in-spite of the front glass cracking it may be possible to heat the front assembly up to the point the adhesive allows the glass to just fall out.... but as far as how close the glue melting point is to the melting point of the plastic frame is not something I know. The entire assembly is put together with some super strong double-sided sticky tape. If you can source just the digitizer and glass assembly I'd like to know.
Once one attempts a replacement and it doesn't work is it still possible to get Fuhu/Nabi to replace the screen (at reasonable cost)?
( If not you could just plug in a keyboard/mouse and use the hdmi out... would make a great XBMC server... once the port exists... )
.
Pictures?
oranrene7 said:
Okay, so my Terminator...errr, my son, managed to crack the heck out of his Nabi 2 digitizer screen. The LCD screen is fine and he can still use the Nabi, but I've noticed more and more cracks so I'm sure it's bound to break the LCD.
So, I went on eBay and ordered a piece of glass, but I'm not thinking it's not going to work. It was only like 13 bucks. I had a model number given to me after the fact (at070tn90), and I just looked and I didn't get that one. I'm just hoping it will work.
At any rate, I finally got the Nabi apart, but I've been fearful of removing the connectors for the screen. Can someone PLEASE tell me how to get the screen apart so I can try to replace it when I get the correct glass for it? PLEASE! There are NO Youtube vids for this...tons for the Nexus 7, but nada for Nabi.
Please help...I'm desperate! Thanks so much!!
Click to expand...
Click to collapse
Do you have any pictures of the digitizer and ribbon cable? Also location of the cable and size measurements.
manx_73 said:
Do you have any pictures of the digitizer and ribbon cable? Also location of the cable and size measurements.
Click to expand...
Click to collapse
I already put it back together because he was taking everyone's iPhones to play games on. lol The glass anatomizer (or whatever it's called), had a long thin strip and the LCD had a thicker one. Either way, the glass nowhere near fit. I had a feeling it was going to be too hard to replace anyway; hence the reason I can't seem to find a tutorial on fixing a Nabi.
And yes, Fuhu will fix it for like 85 bucks plus shipping...I only paid 90 for the tablet just recently (Craigslist). Oh well. I guess we'll just let him play till he cuts his finger.
Thank you both so much for your input. I appreciate it
Help replacing Nabi2 digitizer screen...
Any luck on this?
I have a Nabi 2 on which I've removed the broken digitizer. It was a bit more difficult than I had anticipated. I had to keep the heat gun on the glass and avoid heat-damage to the plastic. I used a small knife between the digitizer and the plastic frame. Next time, I may heat and bend a cheap knife into a Z shape to get under the glass without lifting it too much. I did get it out in some large pieces, but am not sure if I could do it intact if it hadn't been cracked.
Anyhow, the LCD looks great, but I can't seem to find the digitizer anywhere. The ribbon cable has a sticker with the following:
EP0700MLM1
12073*A1G.
272
View attachment 2625405
and on the back side above the chip, is:
40-90121-0
EDT REV.C
View attachment 2625413
on the inside glass is:
85701165
View attachment 2625417
The tiny text in the upper-right corner and written in mirror-image is:
XT2DA5A0118-EP0700 B1
I tried running the text through Google and aliexpress.com / alibaba.com, but to no avail. Anyone else have any luck?
Thanks,
Chip Stewart
ChipStewart said:
Any luck on this?
I have a Nabi 2 on which I've removed the broken digitizer. It was a bit more difficult than I had anticipated. I had to keep the heat gun on the glass and avoid heat-damage to the plastic. I used a small knife between the digitizer and the plastic frame. Next time, I may heat and bend a cheap knife into a Z shape to get under the glass without lifting it too much. I did get it out in some large pieces, but am not sure if I could do it intact if it hadn't been cracked.
Anyhow, the LCD looks great, but I can't seem to find the digitizer anywhere. The ribbon cable has a sticker with the following:
EP0700MLM1
12073*A1G.
272
View attachment 2625405
and on the back side above the chip, is:
40-90121-0
EDT REV.C
View attachment 2625413
on the inside glass is:
85701165
View attachment 2625417
The tiny text in the upper-right corner and written in mirror-image is:
XT2DA5A0118-EP0700 B1
I tried running the text through Google and aliexpress.com / alibaba.com, but to no avail. Anyone else have any luck?
Thanks,
Chip Stewart
Click to expand...
Click to collapse
I am also looking for the same digitizer model any luck? Anyone?
brianbri6 said:
I am also looking for the same digitizer model any luck? Anyone?
Click to expand...
Click to collapse
I am sorry for bringing back an old thread, but has anyone found a source for a proper replacement part for this? I am having a hell of a time finding a replacement part for the digitizer in my nabi2. It's as if nobody makes a replacement for the digitizers with EP0700MLM1 on the ribbon cable. About the only choice I have now is to find a used part, and pray that it also has the same kind of LCD screen within the housing.
--Rex
rex.torres said:
I am sorry for bringing back an old thread, but has anyone found a source for a proper replacement part for this? I am having a hell of a time finding a replacement part for the digitizer in my nabi2. It's as if nobody makes a replacement for the digitizers with EP0700MLM1 on the ribbon cable. About the only choice I have now is to find a used part, and pray that it also has the same kind of LCD screen within the housing.
--Rex
Click to expand...
Click to collapse
I am looking at a few on Fleabay now. You need to take yours apart and compare model numbers with the ones on Ebay. Just search ebay for Nabi 2 digitizer. about 20 results for it, ranging from $25 -65. The $65 one is a complete front panel minus the LCD. just unscrew the top panel and replace, it looks like.
Wow...I'm the original poster...and here I am years later still bothering with Nabi! lol In 2014, I went on Nabi's site and paid $60 to have the digitizer replaced. I never sent the Nabi in because a friend of mine gave me his kid's Nabi to use for parts (he couldn't get it to charge any longer). I took the entire front panel with LCD and digitizer and replaced it with mine. Worked like a charm...until my younger son stepped on it...on purpose! Lil turd! So, here I am again trying to fix the screen, BUT, this time I noted that I needed the LCD and the digitizer (the ribbon on the LCD was breaking off - not sure how that could have happened). At any rate, I ordered both the digitizer and LCD. I replaced them both and it's a no-go...not working. I still have it apart, but I have the cables plugged in, so when I move the screen around, the Nabi screen will come up, but the touchscreen isn't working. I may be sending the digitizer back, but I'm wondering if it's because of how they are lying on one another. Does anyone know if maybe the touchscreen doesn't work if it's too close or too far from the LCD screen. I don't mean by an obvious amount - I mean is there a "specific" amount of space. I am trying to get it in the casing exactly like it was before, but I don't want to do anything permanent until I know it's working 100%.
Also, you can easily and cheaply get the LCD and digitizer for the Nabi now - just stinks you have to order it from China and it takes forever to get here! I can only imagine how long a return/replacement is going to take. Ugh!
Oh, and Nabi has yet to return my $60 bucks...I have spent way too much on this tablet!
I ended up having to match my part number to a used but good part off of ebay. I had ordered several "new" digitizers and they never worked. There seemed to have been a design change somewhere along the line, or some missing information that made mine not work with the "new" parts available at the time.
However, to answer your question, the digitizer will work completely separated from the LCD as long as the ribbon cable is attached (of course). Rather than reassembling everything, I would only connect the digitizer to see if it worked. When I finally found one that worked, I then committed to doing the full repair.
It was a very painful process.
Is it an easy thing to take apart and put bk together if you have never done this before my daughter stood on her Nabi accident it was under her comfort blankie opps screen cracked but works fine she's only 2 ( well advanced for her age) soI dnt want her to use it incase she cuts her tiny fingers doesn't feel sharp but dnt want to risk it can't find any view on u tube still many years on be nice if someone would do one haha
Honestly...
It was a pain in the ass to remove the glass / digitizer from the nabi. If you're not careful--as I was--it is real easy to deform the plastic bezel that the glass / digitizer and LCD reside in. I ended up having to buy a replacement bezel that already had a digitizer and LCD attached to it. The LCD was DOA, but the one from my original was fine, so I begrudgingly transplanted that too.
Test the digitizer FIRST before committing to installing it on the plastic bezel.