I have an Evo V 4G (obviously) it's S-OFF (wire trick) and running the buttered toast kernel, I was on Paranoid Android 2.99 and I kept getting fc's, so I decided to try a few new ROMs, so I tried ViperROM for Sense 4.1, that froze in the boot animation, so I went into 4ext and wiped/flashed a new ROM, but in 4ext, when I hit "info" it still says ViperROM no matter how many times I've wiped it.
I've tried going back and forth retracing my steps and trying different ROMs, aroma installer set ups, and I have no clue.
Any ideas would be very much appreciated.
iZandeR said:
I have an Evo V 4G (obviously) it's S-OFF (wire trick) and running the buttered toast kernel, I was on Paranoid Android 2.99 and I kept getting fc's, so I decided to try a few new ROMs, so I tried ViperROM for Sense 4.1, that froze in the boot animation, so I went into 4ext and wiped/flashed a new ROM, but in 4ext, when I hit "info" it still says ViperROM no matter how many times I've wiped it.
I've tried going back and forth retracing my steps and trying different ROMs, aroma installer set ups, and I have no clue.
Any ideas would be very much appreciated.
Click to expand...
Click to collapse
First suggestion would be to post in the right forum, which for this thread would be Q&A. I've reported it to the mods so they will move it for you.
If you are using 4EXT you should do a "format all partitions except sd card" in the wipe/format menu before flashing a ROM. Then make sure the the S-ON/Smartflash option is disabled in the tools menu, although that won't prevent your ROM from flashing correctly.
Try doing that and giving it plenty of time to boot after you flash it (10 minutes should be enough).
ramjet73
This needs to be in Q&A so get ready for some flames, but I'll attempt to answer.
Go into bootloader and use the wipe all utility there. Then go back to 4-ext and make sure to enable smartflash under settings. Wipe everything except your SD card, and then try to flash something like a sense 3.6 ROM that you know will be stable. Finally, let your device reboot or reboot it when the flash is complete, and let it sit for at least ten minutes. If by then, it still hasn't booted, post back.
Best of luck.
---------- Post added at 04:38 PM ---------- Previous post was at 04:37 PM ----------
ramjet73 said:
First suggestion would be to post in the right forum, which for this thread would be Q&A. I've reported it to the mods so they will move it for you.
If you are using 4EXT you should do a "format all partitions except sd card" in the wipe/format menu before flashing a ROM. Then make sure the the S-ON/Smartflash option is disabled in the tools menu, although that won't prevent your ROM from flashing correctly.
Try doing that and giving it plenty of time to boot after you flash it (10 minutes should be enough).
ramjet73
Click to expand...
Click to collapse
lol beat me to it
nickelghandi said:
lol beat me to it
Click to expand...
Click to collapse
At least we're consistent.
ramjet73
sorry about that guys, I'm not new to forums, I just use AndroidForums more often, I'll give it a try, although I've tried formatting already.
A possibility might be that ViperROM was supposed to be flashed with an RUU fastboot? I'm not really familiar with that method
My guess is Viper needs 1.58 hboot since it a sense rom.
And yeah, wrong forum.
well we've gotten past that, I get it, wrong forum, won't happen again.
That might be true, I'm on Eng 1.04, but I've tried installing Paranoid Android again which worked for me on 1.04, so is there any way I could possibly fix this and get it to boot
Yeah, you definitely need HBOOT 1.57 (Juop HBOOT, the one for Virgin Mobile) if you want this to run. Optionally you can also use 1.58 (Evo 3D ICS Bootloader), but you'll need to modify the SPC in info.txt to make it "02" or "2" I forget which one.
You can of course always fuse the build with the Virgin Mobile Leak kernel, and while you'll lose some stability, it will make it compatible with the ENG Bootloader. Sense 4.1 ROMs are not natively compatible with the ENG bootloader (1.04), because they use a modified version of the 2.89 (RUU) kernel.
thebeastglasser said:
Yeah, you definitely need HBOOT 1.57 (Juop HBOOT, the one for Virgin Mobile) if you want this to run. Optionally you can also use 1.58 (Evo 3D ICS Bootloader), but you'll need to modify the SPC in info.txt to make it "02" or "2" I forget which one.
You can of course always fuse the build with the Virgin Mobile Leak kernel, and while you'll lose some stability, it will make it compatible with the ENG Bootloader. Sense 4.1 ROMs are not natively compatible with the ENG bootloader (1.04), because they use a modified version of the 2.89 (RUU) kernel.
Click to expand...
Click to collapse
thank you, is there any way I can get my phone to boot? I've tried every ROM on my sdcard, whether its JB, MIUI, Sense, Sensless, and it seems to be stuck at this HTC logo, it won't play any boot animation or bootloop, its just stuck
Wipe all partitions, get the original HBOOT 1.57 on it, wipe all partitions again, and then flash Harmonia. Harmonia always boots for me 100% of the time. It's really the only surefire way of doing in my opinion.
If you don't have the Juop HBOOT, here's a download from my personal repository https://www.box.com/s/s64uphj0a37yj7mf3jx1
You probably already know, but rename it PG86IMG.zip, put it on your SD card, and go into bootloader. Once it's there, do the update. Take out your SD and get another one (because you won't be able to get to the recovery anymore) and put Harmonia on it. Your phone should boot, this method has saved me more than once.
iZandeR said:
thank you, is there any way I can get my phone to boot? I've tried every ROM on my sdcard, whether its JB, MIUI, Sense, Sensless, and it seems to be stuck at this HTC logo, it won't play any boot animation or bootloop, its just stuck
Click to expand...
Click to collapse
Some people with this problem have needed to flash the RUU.exe to get it resolved. The Virgin Mobile version is here.
Since you are S-OFF you can just flash that from Windows after putting the phone into "fastboot usb" mode, then flash a custom bootloader and recovery and you will be back in business. You can also boot into the stock ROM and download and install the VM OTA update before flashing the custom recovery. Should take no more than a half hour.
I have a link to the bootloaders and instructions for flashing them available in this post and they all work with both the Evo 3D and Evo V.
ramjet73
thebeastglasser said:
Wipe all partitions, get the original HBOOT 1.57 on it, wipe all partitions again, and then flash Harmonia. Harmonia always boots for me 100% of the time. It's really the only surefire way of doing in my opinion.
If you don't have the Juop HBOOT, here's a download from my personal repository https://www.box.com/s/s64uphj0a37yj7mf3jx1
You probably already know, but rename it PG86IMG.zip, put it on your SD card, and go into bootloader. Once it's there, do the update. Take out your SD and get another one (because you won't be able to get to the recovery anymore) and put Harmonia on it. Your phone should boot, this method has saved me more than once.
Click to expand...
Click to collapse
I updated the HBOOT, but when I plug in my other SD card, it's trying to update the Radio, so I hit no and it automatically reboots (and stays frozen)
on the second SD card, all I need is the harmonia zip?
iZandeR said:
I updated the HBOOT, but when I plug in my other SD card, it's trying to update the Radio, so I hit no and it automatically reboots (and stays frozen)
on the second SD card, all I need is the harmonia zip?
Click to expand...
Click to collapse
You need to delete the PG86IMG.zip file on your SD card. See my previous post if you can't get it working with your current direction.
ramjet73
Yeah, delete it, or snag a second SD. All you're going to need is the harmonia.zip. Flash it, and you should be good to go.
EDIT: And if you really can't get it to boot, the RUU is definitely the way to go. Ramjet is totally right there.
ZWYATT said:
My guess is Viper needs 1.58 hboot since it a sense rom.
And yeah, wrong forum.
Click to expand...
Click to collapse
Not anymore, Virus was nice enough to make his ViperROM compatible with any Hboot I hear.
aoaleman said:
Not anymore, Virus was nice enough to make his ViperROM compatible with any Hboot I hear.
Click to expand...
Click to collapse
That's true. I have r304 booting successfully with the ENG 1.04 hboot.
ramjet73
thebeastglasser said:
Yeah, delete it, or snag a second SD. All you're going to need is the harmonia.zip. Flash it, and you should be good to go.
EDIT: And if you really can't get it to boot, the RUU is definitely the way to go. Ramjet is totally right there.
Click to expand...
Click to collapse
Thanks for the advice, I'll give it a try!
aoaleman said:
Not anymore, Virus was nice enough to make his ViperROM compatible with any Hboot I hear.
Click to expand...
Click to collapse
Yeah, that's what I thought too.
Related
I am an unfortunate rookie, and have made mistakes, hence the name. I want to return my phone to stock from htcdev unlock, s-on, hboot 1.5. with a boot loop on meanom ICS for the evo 3d. I have tried to use older ruu shooters. Relock with fastbot oem lock, and then pg86img. However with the bootloop I can not access anything unless I unlock again, and then go into recovery. This is all that I can think of at the moment that might help.
Kill the rookie!!! PLEASE HELP!!
I had much the same problem with my cdma, hboot 1.5, S-On shooter. When I was S-On none of the ICS roms would work. The all bootlooped on me. If you follow the rooting method found here on xda, it will get you back to a stock Rooted GB Rom.
go into hboot -> fastboot USB-> run command dos -> fastboot cwm-4.0.1.4-shooter.IMG -> flash the 2.17 firmware-> enjoy.
I had to S-off with Juopunutbear, then re-run that root/flash to get past the bootloops.
Sent from my Shooter using xda app-developers app
Unfortunately I have tried that and it still is not working.
My only suggestion would be to try it a few times, other then that, its above my head.
Sent from my shooter using xda app-developers app
rookiemistake said:
I am an unfortunate rookie, and have made mistakes, hence the name. I want to return my phone to stock from htcdev unlock, s-on, hboot 1.5. with a boot loop on meanom ICS for the evo 3d. I have tried to use older ruu shooters. Relock with fastbot oem lock, and then pg86img. However with the bootloop I can not access anything unless I unlock again, and then go into recovery. This is all that I can think of at the moment that might help.
Kill the rookie!!! PLEASE HELP!!
Click to expand...
Click to collapse
Have you tried one of the ruu exe files that you run from your computer? If you are trying to go stock, you should be able to relock the bootloader and run the ruu and that's it.
Sent from my ICS 3VO with Tapatalk 2
First of all I want to thank everyone that has been attempting to assist me with my problem. I have tried to relock since I am on htcdev unlock and then run an ruu force via my computer. I get an installation aborted error when trying to flash pg86img via recovery. I don't know what else to say.
You can't flash a bootloader zip from recovery. You have to flash it from hboot. Also make sure the zip is named correctly "PG86IMG.zip" without the quotes. Also make sure the zip is on the root of your sd as in not in any folders. Once you've named the zip correctly and placed it correctly then power off the phone. Hold down the volume down button and tap the power button. You should boot into the bootloader wait until the phone recognizes the zip and follow the on screen instructions. Hopefully this helps.
#Root-Hack_Mod*Always\=LTE
Thank you again. I tried your directions, it did recognize the pg86img. However it did not give me any instructions to follow. It did however allow me to be able to a partial stock state. My software version is still on the teamgenesis sense v2.9 cdma. Although I do like some of the features on this rom, I would still like to be able to get the OTA of ICS when it is released. Any suggestions?
rookiemistake said:
Thank you again. I tried your directions, it did recognize the pg86img. However it did not give me any instructions to follow. It did however allow me to be able to a partial stock state. My software version is still on the teamgenesis sense v2.9 cdma. Although I do like some of the features on this rom, I would still like to be able to get the OTA of ICS when it is released. Any suggestions?
Click to expand...
Click to collapse
To get the ota release (if it ever comes ) I do believe you will need to be locked and running the existing gingerbread rom. While I am not positive, I think the system uses the props file to determine if an update is applicable, and it will likely not recognize the teamgenesis rom version as being upgradeable.
Now I will likely get flames for saying this, but if you want to put the meanrom v2.4 of ICS on the phone, it can be done with s-on, you just need to follow the correct process. I ran that rom for a while, and it is very stock like, stable, and has a few enhancements that you will not find on a non-rooted stock rom. I never found anything wrong or not working with that rom.
To get it to load, first I downloaded flashimagegui from market, put the meanrom zip file on the sd card and made sure I had a recovery that I could get into. I am using TWRP v2.1.1, lots of folks talk about others like ext4, and I am only going to say use whichever you like, after all it is your phone.
Then with the phone unlocked via the htc method, I started the flashimage app, and browsed to the meanrom file. It extracted the kernel and flashed it. Once that was done, with clear cache buttons selected, rebooted to recovery, and used the install menu selection of TWRP to again flash the same rom file. Once it flashed the file, selected clear cache and dalvik just to be safe, selected reboot system, and it worked great.
Have a great weekend.
So, apparently I am still doing something wrong. I have put the pg86img on the root, relocked to the bootloader, and let it run it's course. However, it will get through with reading it and stops and does not finish anything with loading the system information. I have also tried to run the ruu via usb connection. I keep running into a c++ issue saying runtime error. I have wiped everything and thankfully I did make a backup of the rom and other information that I was runing so I can currently fall back on that.
I am on hboot 1.5, 2.17, and teamgenesis ICS rom for evo 3d.
Apparently there have been rumors that Sprint has finally released the ICS OTA, not that it really matters anymore, but I have run into a few interesting glitches, such as WIFI not staying connected while asleep or disconnecting.
If I have to I am willing to pay to do a netmeeing with someone in order to be able to fix this.
Sorry if it sounds like I am getting frustrated, but I have tried every walkthrough that I have found and have not had any luck with any of them.
Please help.
I forgot to say I am s-on
So I have Scott's CleanROM GBE 1.7.5 on my phone. I was wandering through my phone's settings, and accidentally hit something in the update area. I do not know what I was thinking, but I know I expected it to ask me if I was sure I wanted to update. So far it has only done the first part where it prepares the phone for the update. I do not know when the other part is coming but I assume it is automatic. I was planning on updating to a rooted ICS once I felt comfortable with it (just seemed a little harder than my original flash of rooted GB). So if it would be easier to just update to ICS some way now, I would be very willing to do that. I am s-on, I believe I installed Amon Ra, but I am not sure how to check and not sure if I have an actual recovery rom or not.
I checked around and found similar problems, but nothing really like mine since my update has not gone all the way thru yet. If anyone could help, it would be greatly appreciated. THank you.
Easiest way is to relock your bootloader, run the newest ruu, unlock and flash recovery again. That way you will be set up to run any ics Rom without having to worry about flashing a patch
Sent from my ADR6425LVW using Tapatalk 2
pwned3 said:
Easiest way is to relock your bootloader, run the newest ruu, unlock and flash recovery again. That way you will be set up to run any ics Rom without having to worry about flashing a patch
Sent from my ADR6425LVW using Tapatalk 2
Click to expand...
Click to collapse
Ok just to make sure I know and don't mess anything else up. I relock (should be easy to.find a guide) . Then run the update on my phone? Then unlock thru HTC again, and flash the actual amon or CWM to my phone? And from there I will be able to flash any ICS Rom with more ease?
And thank you for the quick reply.
Edit: I searched the internet more for less-similar situations. I think all I have to do is re-lock. Download the newest RUU from Android police and put it in the root of the SD card as PH98IMG.zip (I'm assuming it should be the internal memory, but please correct me if I am wrong.) Hold volume down & power to boot into bootloader, then the phone takes it from there?
Also,nothing I have to do as far as unrooting?
malignancyy said:
Also,nothing I have to do as far as unrooting?
Click to expand...
Click to collapse
Nope just relock the bootloader
AshtonTS said:
Nope just relock the bootloader
Click to expand...
Click to collapse
Okay, thanks a lot. And I edited this into a prior post, but I just wanted to make sure:
I have to re-lock. Download the newest RUU from Android police and put it in the root of the SD card as PH98IMG.zip (I'm assuming it should be the internal memory, but please correct me if I am wrong.) Hold volume down & power to boot into bootloader, then the phone takes it from there?
malignancyy said:
Okay, thanks a lot. And I edited this into a prior post, but I just wanted to make sure:
I have to re-lock. Download the newest RUU from Android police and put it in the root of the SD card as PH98IMG.zip (I'm assuming it should be the internal memory, but please correct me if I am wrong.) Hold volume down & power to boot into bootloader, then the phone takes it from there?
Click to expand...
Click to collapse
Then you just have to press continue when it tells you to.
PS: Another way to get to the bootloader is to use adb (make sure USB debugging is enabled on your phone)
Command:
adb reboot bootloader
I find it easier than holding down buttons for a long time, but that's just my personal preference.
(Also, most custom ROMs can reboot to bootloader from within the ROM. I forget if CleanROM GBE includes the advanced power menu.)
pwned3 said:
Easiest way is to relock your bootloader, run the newest ruu, unlock and flash recovery again. That way you will be set up to run any ics Rom without having to worry about flashing a patch
Sent from my ADR6425LVW using Tapatalk 2
Click to expand...
Click to collapse
Good advise, and if he RUUs to ICS, then he should not even get asked to install the update because it will already be installed on his phone.
Also RUU twice. Just reboot into bootloader right away and install the RUU a second time. Then boot up normally and remove the zip file from the sdcard.
Thanks, you all helped a lot. I was able to get the stock rom, rooted, and running smoothly. But, once I tried to install custom roms I had problems. I decided to S-off to make it easier from here on out. After a few tries, it said I had successfully done the S-off. I tried to install Juopunutbear custom hboot, directly afterwards and it said it installed but I was stuck on the Juopunutbear screen. After this, I have not been able to get past hboot.I do not think the custom hboot actually installed. It is saying from the top:
***TAMPERED***
***LOCKED***
VIGOR PVT SHIP S-OFF RL
HBOOT-2.27.0000
RADIO-2.22.10.0801r/2.22.10.0803r
OpenDSP-v14.6.0.7708.00.0507
eMMC-boot
Aug 6 2012, 19:24:37
My external sd card needed formatting, so I just did that. And my plan is to RUU again (i guess twice), flash recovery (when clicked on currently, nothing happens), I guess root although I am not sure about this part, then try to install a custom rom.
Didn't want to make another thread just to check on this, but does this sound about right?
And as far as installing rom since I am now s-off, just go to recovery and flash it, nothing else at all to worry about?
malignancyy said:
Thanks, you all helped a lot. I was able to get the stock rom, rooted, and running smoothly. But, once I tried to install custom roms I had problems. I decided to S-off to make it easier from here on out. After a few tries, it said I had successfully done the S-off. I tried to install Juopunutbear custom hboot, directly afterwards and it said it installed but I was stuck on the Juopunutbear screen. After this, I have not been able to get past hboot.I do not think the custom hboot actually installed. It is saying from the top:
***TAMPERED***
***LOCKED***
VIGOR PVT SHIP S-OFF RL
HBOOT-2.27.0000
RADIO-2.22.10.0801r/2.22.10.0803r
OpenDSP-v14.6.0.7708.00.0507
eMMC-boot
Aug 6 2012, 19:24:37
My external sd card needed formatting, so I just did that. And my plan is to RUU again (i guess twice), flash recovery (when clicked on currently, nothing happens), I guess root although I am not sure about this part, then try to install a custom rom.
Didn't want to make another thread just to check on this, but does this sound about right?
And as far as installing rom since I am now s-off, just go to recovery and flash it, nothing else at all to worry about?
Click to expand...
Click to collapse
The jbear hboot might have failed because you are on the newest global update with 2.27 hboot, and I believe the controlbear tool still has the 2.25 hboot. (someone correct me if I'm wrong)
I think there is an unguarded 2.27 hboot somewhere, so you should flash that manually.
Sent from my NeoMax Rezound
Right now, like I said the hboot says at the top 2.27.0000
When I reboot from there, or boot it regularly it goes to a JuopunutBear, black and green writing screen.
I have tried to install this forum.xda-developers.com/showthread.php?t=1843030 ([HBOOT] HBoot 2.27 (from 4.03.605 OTA) Unlocked) from both, but cannot figure out how to do so.
edit: within JuopunutBear, wiping says "can't open" and applying update gives "failed to open loopdevice" and "failed to mount /sdcard" when I try to update.
Within the regular hboot, I get "no image" as it searches for files.
Well, I put the same file on a new sd card, and it worked on the first try, kinda.
Now it appears my phone is bricked. It will not boot at all. She barely lasted a few hours s-off before I messed it up. Any tips anyone out there can give to this sad fellow, or am I off to get a replacement?
A little more info on this. Windows tries installing QHUSB_DLOAD driver for it when plugged in, but unsuccessfully. The charging indicator does not come on either. Have tried to turn it on plugged in with battery out, and battery in both ways.
malignancyy said:
Well, I put the same file on a new sd card, and it worked on the first try, kinda.
Now it appears my phone is bricked. It will not boot at all. She barely lasted a few hours s-off before I messed it up. Any tips anyone out there can give to this sad fellow, or am I off to get a replacement?
Click to expand...
Click to collapse
Depending on what caused the brick, it may be recoverable.
Check out the unbricking thread in the dev section.
Sent from my NeoMax Rezound
Wanted to post this in the NeoMax thread, but I am currently not allowed to. I gave up on my last Rezound, and am getting a replacement here soon. I did a bunch of reading before and after I got my Rezound, and a bunch more the past few days as I wanted to get an ICS rom. Unfortunately, the one time I deferred from guides I followed (installing the JBear hboot), I killed my Rezound. I now want to stay S-on, at least until I gain some more familiarity and skill with this whole process.
What I plan on doing is once I get the Rezound, installing the OTA update, possibly having to wait for it to do so. I assume this would be the newest, .2, global update. I plan to unlock, flash recovery, then root. The rom I really want however is NeoMax. There are limited instructions on how I go about this. But from what I understand I change the filename to PH98IMG and flash it from hboot? The file name is originally, GlobalRuuPH98IMG.zip, but the thread title claims ICS De-Sensed 3.14.605.12, which I believe is two versions prior. So here I am lost. If it is in fact older, I have to flash the rom through recovery, then flash the kernel, correct? If so, do I just use the 3.14.605 that was in the NeoMax thread?
Sorry to bother you all with what i'm sure others have done many times. Like I said, I have read a lot on this, its just that I either did not understand in the least what the guides were saying, or it seemed like this situation was much different. And on a side note, if there is any other rom out there that someone would recommend that would make this easier (such as being on the latest kernel), I wouldn't be opposed to trying it. I just want one that is desensed, as it is one of my main reasons for wanting a custom rom.
malignancyy said:
Wanted to post this in the NeoMax thread, but I am currently not allowed to. I gave up on my last Rezound, and am getting a replacement here soon. I did a bunch of reading before and after I got my Rezound, and a bunch more the past few days as I wanted to get an ICS rom. Unfortunately, the one time I deferred from guides I followed (installing the JBear hboot), I killed my Rezound. I now want to stay S-on, at least until I gain some more familiarity and skill with this whole process.
What I plan on doing is once I get the Rezound, installing the OTA update, possibly having to wait for it to do so. I assume this would be the newest, .2, global update. I plan to unlock, flash recovery, then root. The rom I really want however is NeoMax. There are limited instructions on how I go about this. But from what I understand I change the filename to PH98IMG and flash it from hboot? The file name is originally, GlobalRuuPH98IMG.zip, but the thread title claims ICS De-Sensed 3.14.605.12, which I believe is two versions prior. So here I am lost. If it is in fact older, I have to flash the rom through recovery, then flash the kernel, correct? If so, do I just use the 3.14.605 that was in the NeoMax thread?
Sorry to bother you all with what i'm sure others have done many times. Like I said, I have read a lot on this, its just that I either did not understand in the least what the guides were saying, or it seemed like this situation was much different. And on a side note, if there is any other rom out there that someone would recommend that would make this easier (such as being on the latest kernel), I wouldn't be opposed to trying it. I just want one that is desensed, as it is one of my main reasons for wanting a custom rom.
Click to expand...
Click to collapse
Don't worry, you're not bothering anyone.
The people who claim to have bricked their phones when they have a boot loop and say nothing about their rom and firmware are bothering people.
Keep doing what you are currently doing and people will always be willing to help you.
Ok, so back to helping...
Of you're starting on GB, make sure you update to 3.14.605.12 before updating to the most recent one.
If you update via OTA then you don't need to worry.
Keep in mind that NeoMax is based off of the 3.14.605.12 build, so you'll have to mix n match the right way to get it to work on the latest firmware.
I believe it was you have to use the new kernel if you use the new radios and hboot.
So after installing NeoMax, flash the PH98IMG that contains the newer kernel, not the 3.14.605.12 version.
Or use fastboot to flash the kernel. (my preferred method while s-on)
Sent from my NeoMax Rezound
PS: A good way to get the required 10 posts to post in the dev section is post random stuff in the off topic thread.
wlmeng11 said:
Don't worry, you're not bothering anyone.
The people who claim to have bricked their phones when they have a boot loop and say nothing about their rom and firmware are bothering people.
Keep doing what you are currently doing and people will always be willing to help you.
Ok, so back to helping...
Of you're starting on GB, make sure you update to 3.14.605.12 before updating to the most recent one.
If you update via OTA then you don't need to worry.
Keep in mind that NeoMax is based off of the 3.14.605.12 build, so you'll have to mix n match the right way to get it to work on the latest firmware.
I believe it was you have to use the new kernel if you use the new radios and hboot.
So after installing NeoMax, flash the PH98IMG that contains the newer kernel, not the 3.14.605.12 version.
Or use fastboot to flash the kernel. (my preferred method while s-on)
Sent from my NeoMax Rezound
PS: A good way to get the required 10 posts to post in the dev section is post random stuff in the off topic thread.
Click to expand...
Click to collapse
As far as which kernel, this is what was said in the NeoMAX Q&A:
Q: "I flashed your rom and my phone gets really hot after a while. In fact, Ive noticed it on all the newer roms lately. What could be causing it and how can I attempt to fix it?"
A: "Make sure you have updated your radio to the latest available and then flash the 2nd to latest kernel. This combination has been known to have the best rom performance for all my roms and decreased heat"
SO this means I should use the 4.03.605.1? And the newest radio will automatically still be on there from the OTA update, or will I have to flash those as well? I have no experience in flashing radios so this is new ground to me.
malignancyy said:
As far as which kernel, this is what was said in the NeoMAX Q&A:
Q: "I flashed your rom and my phone gets really hot after a while. In fact, Ive noticed it on all the newer roms lately. What could be causing it and how can I attempt to fix it?"
A: "Make sure you have updated your radio to the latest available and then flash the 2nd to latest kernel. This combination has been known to have the best rom performance for all my roms and decreased heat"
SO this means I should use the 4.03.605.1? And the newest radio will automatically still be on there from the OTA update, or will I have to flash those as well? I have no experience in flashing radios so this is new ground to me.
Click to expand...
Click to collapse
That QA is outdated.
It was referring to using the 3.14.605.07 kernel as opposed to the then-most-recent 3.14.605.10
Back then those two builds were similar enough that they could mix n match without issues.
Between 3.14.605.12 and 4.03.605.1 is a lot of changes. (whole number change to represent it) Specifically, new hboot and radios. Therefore, it is incompatible with the older kernels.
When you're S-ON you can't touch the radios except through an official RUU.
Even with s-off I doubt you can flash radios from recovery (not sure on this one), and NeoMax doesn't have any radio files anyway. (nor does any rom I know for this phone)
If you haven't yet updated to 4.03.605.1 then I recommend that you stay on 3.14.605.12 until Neo updates the ROM.
If you already updated, it is still possible to run NeoMax. You just have to manually flash the new 4.03.605.1 kernel after installing the ROM.
Sent from my NeoMax Rezound
I've been (at least trying to) patiently wait for Deck to post full install instructions for CM10 but the CM10 op is still bare as bones. Has anyone else posted an install guide or instructions yet?
I'm currently rooted with RegawMod and running MeanRom 2.1 and it's really terribly laggy and frustrating, I can't wait any longer for CM10. Do I need S-off to install CM10 or do I just wipe, flash, and go?
Thanks for any help or links!
If you are on hboot 1.15 or higher you have to fast boot flash the kernel.
Other than that its just like a normal aosp install. Wipe flash rom flash gapps.
Its been my daily for 3 weeks.
Sent from my EVO using Tapatalk 2
You don't need s-off. You will however have to flash the boot IMG separately by using fastboot or the app flash image GUI and a full wipe is definitely required. There is a helpful thread in Q&A called "don't panic" that will answer all your questions
Good luck
Sent from my EVO using xda app-developers app
corcgaigh said:
You don't need s-off. You will however have to flash the boot IMG separately by using fastboot or the app flash image GUI and a full wipe is definitely required. There is a helpful thread in Q&A called "don't panic" that will answer all your questions
Good luck
Click to expand...
Click to collapse
Dont use flash image gui unless you know how to do it manually through fastboot. You are just asking for issues
Instructions:
http://androidforums.com/evo-4g-lte-all-things-root/606748-how-install-kernels-h-boot-1-15-a.html
Rxpert said:
If you are on hboot 1.15 or higher you have to fast boot flash the kernel.
Other than that its just like a normal aosp install. Wipe flash rom flash gapps.
Click to expand...
Click to collapse
I'm on hboot 1.12, so does that mean I can just flash normally?
edit - From what I can tell from reading, hboot 1.12 doesn't have the same restrictions that 1.15+ do, so I think I'm OK but I would like verification.
Thanks for the help everyone.
Yes hboot 1.12 allows for access to the boot partition
Also luuuuucckkyyyyyy...
EdhyMonker said:
I'm on hboot 1.12, so does that mean I can just flash normally?
edit - From what I can tell from reading, hboot 1.12 doesn't have the same restrictions that 1.15+ do, so I think I'm OK but I would like verification.
Thanks for the help everyone.
Click to expand...
Click to collapse
If you are on Hboot 1.12 I'd strongly suggest looking into getting S-OFF. Theres really no reason not to.
Up to you though, its not required
Bit off topic, anyone check to see if you can push a new splash, right now I'm too lazy to start my PC just to fastboot one measly splash
Rxpert said:
If you are on Hboot 1.12 I'd strongly suggest looking into getting S-OFF. Theres really no reason not to.
Up to you though, its not required
Click to expand...
Click to collapse
The S-OFF guide was way over my head so I just let it be. If there's not a real good reason for doing it, and I can still run CM10, then I'd rather not.
It allows you to directly flash new firmware like radios to fix any problems a device might be having. If you have Son and want the latest firmware you have to revert back to stock and accept ota, then unlock reflash recovery and reflash custom ROM or rooted stock, you could also just flash root installer if you want to just root stock
om4 said:
It allows you to directly flash new firmware like radios to fix any problems a device might be having. If you have Son and want the latest firmware you have to revert back to stock and accept ota, then unlock reflash recovery and reflash custom ROM or rooted stock, you could also just flash root installer if you want to just root stock
Click to expand...
Click to collapse
No, S-ON people with 1.12 H-boot can flash radios and firmware from recovery. They can do whatever they please in recovery just like S-OFF. S-OFF users can flash things from bootloader and even change the appearance of their h-boot to read S-ON and **locked** even though they are S-OFF
To the OP, this is the best rooting guide I've seen. It really explains everything step by step. http://androidforums.com/evo-4g-lte...panda-s-htc-dev-ltevo-root-dummies-guide.html Its recommended to have Linux at least bootable, because in the small chance the phone gets bricked... the unbricker program requires linux.
I ran it in windows before the unbricker was available, no issues here
You basically just hook the phone up to it and run the program like you do for most other root programs. All 1-click
Ah yeah forgot to mention that, most everyone is on 1.15 or 1.19 sorry
om4 said:
Ah yeah forgot to mention that, most everyone is on 1.15 or 1.19 sorry
Click to expand...
Click to collapse
Alright, I got S-Off using Lazy Panda and it went better than expected!
Do I need to flash updated firmware / radios separately from CM10, or does CM10 include latest firmware?
Sorry to ask dumb questions, but I do hope this thread will also be a good resource for others like me.
You don't have to flash any firmware updates. There are a few users with issues although they may be related to the ROM update and not necessarily the firmware included. I haven't really checked since I'm s on. If you want to update the radios there's an update zip here somewhere, be sure to read through everything carefully. Radios are more risky then every day flashing
Alright everyone now I need some help!
I flashed CM10 after s-off, was on stocked 1.13 rooted rom.
Now when CM10 boots up I am faced with a phone activation screen. It says something like "you will not be able to place calls or access the mobile network until the device is activated". I am unable to make calls or receive calls or access the internet. I have tried reflashing cm10 and the problem persists.
In the mean time, I will try flashing a nand backup and see where that gets me. I appreciate any and all help, and I have found no posts in the CM10 thread with a similar issue.
Update: I wiped and restored a back-up, MeanRom 2.1. Upon boot, hands-free activation ran and activated the phone and downloaded a PRL update. Everything is working fine now. Not sure if I should try CM10 again or what? Any advice?
EdhyMonker said:
Alright everyone now I need some help!
I flashed CM10 after s-off, was on stocked 1.13 rooted rom.
Now when CM10 boots up I am faced with a phone activation screen. It says something like "you will not be able to place calls or access the mobile network until the device is activated". I am unable to make calls or receive calls or access the internet. I have tried reflashing cm10 and the problem persists.
In the mean time, I will try flashing a nand backup and see where that gets me. I appreciate any and all help, and I have found no posts in the CM10 thread with a similar issue.
Update: I wiped and restored a back-up, MeanRom 2.1. Upon boot, hands-free activation ran and activated the phone and downloaded a PRL update. Everything is working fine now. Not sure if I should try CM10 again or what? Any advice?
Click to expand...
Click to collapse
ive only ever seen this issue with cyanogenmod and the old htc vogues, still great phones for what they were
EdhyMonker said:
Alright, I got S-Off using Lazy Panda and it went better than expected!
Do I need to flash updated firmware / radios separately from CM10, or does CM10 include latest firmware?
Sorry to ask dumb questions, but I do hope this thread will also be a good resource for others like me.
Click to expand...
Click to collapse
Yes, you should be flashing the upgraded firmware. You'll see the full firmware as the very first downloadable link. Flash that
http://themikmik.com/showthread.php...dio-Collection&p=220556&viewfull=1#post220556
Rename the file to "PJ75IMG.zip", place on root of SD card, and boot into HBOOT to flash. Check the md5 to make sure its right. With radios you want to make sure its the correct file.
Welcome to S-OFF my friend
Rxpert said:
Yes, you should be flashing the upgraded firmware. You'll see the full firmware as the very first downloadable link. Flash that
http://themikmik.com/showthread.php...dio-Collection&p=220556&viewfull=1#post220556
Rename the file to "PJ75IMG.zip", place on root of SD card, and boot into HBOOT to flash. Check the md5 to make sure its right. With radios you want to make sure its the correct file.
Welcome to S-OFF my friend
Click to expand...
Click to collapse
Thanks, but I tried this and it says "no image or wrong image" when trying to flash the PJ75IMG.zip file.
Did you type in PJ75IMG.zip or PJ75IMG and kept it a zip file...you should do the 2nd.
joebarkho said:
Did you type in PJ75IMG.zip or PJ75IMG and kept it a zip file...you should do the 2nd.
Click to expand...
Click to collapse
I thought that might've been the issue so I tried it both ways, didn't work either way. I'll take another shot at it tomorrow.
I don't want to be giving my friend the wrong information. When his sprint 3d was boot 1.5 I took it and soff it for him downgrading to 1.4. Now recently he upgraded to hboot 1.58 and it says relocked at the top. Of course he still has recovery and still is rooted.
My question is since his phone is soff can't he just still flash whatever with no issues? Does he have to do dev unlock again?
I own a rezound and have had many HTC devices and soff has always been the key to everything for me. Any help would be appreciated
With s-off there's no need to unlock his boot loader again. (For example) If he wants to flash an aosp rom, all he's gotta do is downgrade his hboot via boot loader.
Perfect. Already installed JP bear latest hboot and went to twrp. Making a backup now. That's what I was thinking but I wanted some confirmation. Its been a while since I messed with an Evo 3d
Hmmm. It won't flash paranoid android. Even tried the 1.04 eng hboot. Any ideas? Using twrp recovery. Latest radios and 1.04 eng hboot.
stkiswr said:
Hmmm. It won't flash paranoid android. Even tried the 1.04 eng hboot. Any ideas? Using twrp recovery. Latest radios and 1.04 eng hboot.
Click to expand...
Click to collapse
A lot of people have had better luck with 4EXT on the Evo 3D. You can download the Recovery Updater for free from the www.4ext.net website and install the current version of 4EXT Recovery from that app. Then "format all partitions except SD card" in the wipe/format menu of the recovery, and try flashing PA again.
ramjet73
ramjet73 said:
A lot of people have had better luck with 4EXT on the Evo 3D. You can download the Recovery Updater for free from the www.4ext.net website and install the current version of 4EXT Recovery from that app. Then "format all partitions except SD card" in the wipe/format menu of the recovery, and try flashing PA again.
ramjet73
Click to expand...
Click to collapse
K. I'm working on that now. I let you know soon its backing up now. Thank you for the heads up. Do you think I should go back yo the latest jbear hboot? Or just leave the 1.04 eng hboot? He wants to be able to run these jellybean builds that are out
stkiswr said:
K. I'm working on that now. I let you know soon its backing up now. Thank you for the heads up. Do you think I should go back yo the latest jbear hboot? Or just leave the 1.04 eng hboot? He wants to be able to run these jellybean builds that are out
Click to expand...
Click to collapse
Stay with the ENG 1.04 hboot for now. The GB and AOSP based ROM's won't boot with the latest JBear (1.58.5858) so if you want to use a JBear version 1.50.5050 is better.
ramjet73
ramjet73 said:
Stay with the ENG 1.04 hboot for now. The GB and AOSP based ROM's won't boot with the latest JBear (1.58.5858) so if you want to use a JBear version 1.50.5050 is better.
ramjet73
Click to expand...
Click to collapse
Wow thank you for all the help. I just did everything and unfortunately it is just stuck in a never ending splash loop. Doesn't seem like the kernel/boot is being flashed. Made a backup so I should be good. Just sucks doing all the steps and being stuck.
What kernel are you flashing with pa?
Jsparta26 said:
What kernel are you flashing with pa?
Click to expand...
Click to collapse
It doesn't come with a kernel?
stkiswr said:
Wow thank you for all the help. I just did everything and unfortunately it is just stuck in a never ending splash loop. Doesn't seem like the kernel/boot is being flashed. Made a backup so I should be good. Just sucks doing all the steps and being stuck.
Click to expand...
Click to collapse
Are you doing the "format all partitions except SD card" in 4EXT right before flashing the ROM? Make sure to give it plenty of time to boot since sometimes the first boot can take up to 10 minutes.
ramjet73
stkiswr said:
It doesn't come with a kernel?
Click to expand...
Click to collapse
Well go with ramjets suggestion and try format all partitions minus sdcard along with full factory data wipe and cache/dalvik wipe and see if it boots up all the way.( it couldn't hurt to do all the wipes two or three times before you flash the rom). Just to make sure everything was wiped all the way.
Oh yeah. Step by step . It just never gets past splash. I looked into the ROM downloaded and saw a boot IMG but it really seems like a boot issue. Doesn't make a lot of sense to me. Soff, everything in right place, correct recovery and no boot. Not complaining, he still has his backup he is running and it restores backup correctly.
His phone was soff and he upgraded firmware to the 1.58 so it said locked in hboot. I just flashed 3 dif bootloader with no issues. Its def soff.
Ok, try flashing a different kernel. Try the Mac kernel that's located in Mazda's aokp jb thread. I believe buttered toast came with pa that your trying to flash. It could also be a bad download as well. You could always redownload the rom as well to see if that works. You never know about these things sometimes.
stkiswr said:
Oh yeah. Step by step . It just never gets past splash. I looked into the ROM downloaded and saw a boot IMG but it really seems like a boot issue. Doesn't make a lot of sense to me. Soff, everything in right place, correct recovery and no boot. Not complaining, he still has his backup he is running and it restores backup correctly.
His phone was soff and he upgraded firmware to the 1.58 so it said locked in hboot. I just flashed 3 dif bootloader with no issues. Its def soff.
Click to expand...
Click to collapse
You've tried all the standard stuff to get AOSP ROM's to boot on the Evo 3D. At this point I can only suggest that you flash the 2.89.651.2 SPrint ICS RUU from here, then reflash a custom bootloader and recovery. That will make sure everything is in sync and has cleared up this problem for other users.
You don't need to relock the bootloader (although I think you said it is already relocked) when flashing the RUU if the phone is S-OFF.
ramjet73
Yes, I will try to download ROM again and also grab that kernel.
I soff this phone for him when it was hboot 1.50. Then I reverted to 1.40 via brick method to get it soff. He has ran some form of an hboot/radios update because he was told to do that. Now we are working together and I am trying to fix all his stuff and get him setup correctly. I have an soff rezound and am sure his phone isn't seeing the boot.IMG.
Now today his phone said locked or relocked am not sure. I went ahead an changed his hboot to a recommended 1.04eng hboot. Installed 4ext recovery via the app that was linked. I am downloading gangam style cm10 to test just to see if something will boot. It successfully flashed a sense based ROM and booted fine thru an aroma installer that came with the ROM. In the installer I stated it was soff and had no issues. I will try the ROM and it doesn't boot I will jump back to recovery and flash a kernel and see. Thanks very much for all the help
Well, I have done it all. Not much more I can do. He may try to run the ICS ruu later but I just can't get any cm10 jb based ROM to boot. Y'all have been more than helpful catching me back up to speed on the 3d and while I agree this should be flashing alas it is not booting. I am positive its just not accepting the boot img for what ever reason because it never makes it far enough after reboot from recovery. Just endless quick splash screen reboots.
No problem. I just wanted to add that a lot of users are having weird issues with paranoid android. ( I'm subscribed to the thread) so it could be that your phone doesn't like pa for some reason. ( Not a diss on Lens Flare at All) but he's been having some issues with the rom and is more than likely trying to work on it. Hopefully you can get gangnam style up and running or even aokp jb. If none of these work, I would go with ramjets suggestion and run a ruu and then back to Asop.
Edit: guess you already tried them. Hopefully you get some better luck after you try the ruu method. Good luck.
So I'm currently on Flyhalf's CM10.1 (S-ON), and I checked the recommended firmware/radios for the ROM and realized I'm outdated. It calls for Hboot 2.26 and radio 2.23.10.0123r, 2.23.10.0124r. but I'm on 2.25 and 1.22.10.0421r/1.22.10.0424r. I just updated to the latest version of the rom and I keep getting random bootlooping as well as the rom being way more unstable than the previous build I was on for about 4 months.
So, I'm trying to use Wildhorse's guide to updating firmware through RUU in hopes that it will solve my problems and it just plain isn't working. I've put the RUU in my external SD as PH98IMG, waited for my battery to charge to 90%, shut off the phone, pulled the battery, then gone into Hboot to flash it but I keep getting "No Image or Wrong Image" and it just goes back to the main Hboot screen every single time. Can anyone explain to me why this is happening even though I'm following everybody's directions exactly? I've been searching through the forums for about 2 hours now and I can't get an answer.
I'm still kind of new to HTC devices and how they work, so if anyone could help me figure this out I'd be very thankful.
BrahManty said:
So I'm currently on Flyhalf's CM10.1 (S-ON), and I checked the recommended firmware/radios for the ROM and realized I'm outdated. It calls for Hboot 2.26 and radio 2.23.10.0123r, 2.23.10.0124r. but I'm on 2.25 and 1.22.10.0421r/1.22.10.0424r. I just updated to the latest version of the rom and I keep getting random bootlooping as well as the rom being way more unstable than the previous build I was on for about 4 months.
So, I'm trying to use Wildhorse's guide to updating firmware through RUU in hopes that it will solve my problems and it just plain isn't working. I've put the RUU in my external SD as PH98IMG, waited for my battery to charge to 90%, shut off the phone, pulled the battery, then gone into Hboot to flash it but I keep getting "No Image or Wrong Image" and it just goes back to the main Hboot screen every single time. Can anyone explain to me why this is happening even though I'm following everybody's directions exactly? I've been searching through the forums for about 2 hours now and I can't get an answer.
I'm still kind of new to HTC devices and how they work, so if anyone could help me figure this out I'd be very thankful.
Click to expand...
Click to collapse
You are on a leaked firmware, the currently available RUUs are all older than that, and you can't go back when you are S-ON. You need to S-OFF then you can RUU back to 3.14.605.12 and then OTA back up to the current 4.5.605.14
acejavelin said:
You are on a leaked firmware, the currently available RUUs are all older than that, and you can't go back when you are S-ON. You need to S-OFF then you can RUU back to 3.14.605.12 and then OTA back up to the current 4.5.605.14
Click to expand...
Click to collapse
Okay, I was really hoping that wasn't the case. I hate to ask for more help, but I don't really understand how I'm supposed to get S-Off when I need to be on the stock RUU to do it, and I can't get on the stock RUU because I need to be S-Off to do so...
I hope I'm not stuck this way. Technically I'm on all the same software as I was yesterday, but now I'm getting random reboots all the time as well as bootloops that either go on for ten minutes or never end. I was on a build of CM10.1 from may with Amon Ra recovery, then tried to flash the newest TWRP that requires the new firmware (didn't realize I was on older firmware) and it bricked my phone. So I put on an older CWM recovery, tried to backup and it froze in the middle of every backup it tried to make. Put on an old TWRP, backups worked, so I flashed the newest version of CM10.1 (again not knowing I didn't have newest firmware) and that's when the bootlooping/rebooting started. I recovered to the old version of CM10.1 and the issue didn't go away, so now I'm just trying to figure out what I can do to get my phone in a usable state again.
BrahManty said:
Okay, I was really hoping that wasn't the case. I hate to ask for more help, but I don't really understand how I'm supposed to get S-Off when I need to be on the stock RUU to do it, and I can't get on the stock RUU because I need to be S-Off to do so...
I hope I'm not stuck this way. Technically I'm on all the same software as I was yesterday, but now I'm getting random reboots all the time as well as bootloops that either go on for ten minutes or never end. I was on a build of CM10.1 from may with Amon Ra recovery, then tried to flash the newest TWRP that requires the new firmware (didn't realize I was on older firmware) and it bricked my phone. So I put on an older CWM recovery, tried to backup and it froze in the middle of every backup it tried to make. Put on an old TWRP, backups worked, so I flashed the newest version of CM10.1 (again not knowing I didn't have newest firmware) and that's when the bootlooping/rebooting started. I recovered to the old version of CM10.1 and the issue didn't go away, so now I'm just trying to figure out what I can do to get my phone in a usable state again.
Click to expand...
Click to collapse
Hey, wait a sec... :laugh:
My bad, I just double checked, and with that Hboot/radio combination you are on stock ICS firmware already! Just RUU version 3.14.605.12, that should work without issues if done correctly and you should be back to pure ICS and can then allow the OTA to upgrade you in a few steps to 4.5.605.14
acejavelin said:
Hey, wait a sec... :laugh:
My bad, I just double checked, and with that Hboot/radio combination you are on stock ICS firmware already! Just RUU version 3.14.605.12, that should work without issues if done correctly and you should be back to pure ICS and can then allow the OTA to upgrade you in a few steps to 4.5.605.14
Click to expand...
Click to collapse
Oh, thank god. Hahah. I didn't remember ever flashing any leaked firmware before, so I was kind of confused there. I figured I may have done it somewhere in the unlocking/rooting process and just couldnt remember. Okay, thanks again for the help. RUU's have always confused me with the way they work. I should be stable in no time hopefully.
And now I'm having more issues... I can't use the Rom Updater because somethings wrong with my usb connection. I can plug it in and transfer files and such, but trying to use any ADB commands results in "Device not found" and the Rom Updater says it can't connect to my device either. My HTC Drivers are up to date, so I'm not sure why this is happening. Is there any way I can just get the PH98IMG.zip for 3.14.605.12 instead of having to use the RUU?
Not really sure what you are trying to run, I didn't think there was a 3.14.605.12 executable RUU, but use this page and instructions and grab the file: http://www.androidpolice.com/2012/0...cream-sandwich-ruu-for-final-ota-3-14-605-12/
Remember you will need to RELOCK the bootloader if I am not mistaken it is possible to hard brick if you don't!
Then copy to external SD card, name the file PH98IMG.zip (beware of the Windows "double zip" issue), verify MD5 on the SDcard, then reboot into hboot and go. Do it twice!!! Let it boot up and sit for about 10 minutes to calm down, then remove the PH98IMG.zip file from the SD card. Everything should be smooth sailing from there...
You should then be S-ON, completely stock. You will need to unlock again to do anything more
acejavelin said:
Not really sure what you are trying to run, I didn't think there was a 3.14.605.12 executable RUU, but use this page and instructions and grab the file: http://www.androidpolice.com/2012/0...cream-sandwich-ruu-for-final-ota-3-14-605-12/
Remember you will need to RELOCK the bootloader if I am not mistaken it is possible to hard brick if you don't!
Then copy to external SD card, name the file PH98IMG.zip (beware of the Windows "double zip" issue), verify MD5 on the SDcard, then reboot into hboot and go. Do it twice!!! Let it boot up and sit for about 10 minutes to calm down, then remove the PH98IMG.zip file from the SD card. Everything should be smooth sailing from there...
You should then be S-ON, completely stock. You will need to unlock again to do anything more
Click to expand...
Click to collapse
Strange, re-locking the bootloader was all I needed to get the RUU to update in my bootloader. No one else said to do that in any of the instructions, but I did it and immediately it started updating with the PH98IMG that I was originally trying to flash (from here: http://forum.xda-developers.com/showpost.php?p=38527788&postcount=745&nocache=1&z=1965375486761331).
I'm back to stock now, but firmware is 4.03.605.2, not 4.03.605.14. Is that going to be an issue or can I go right ahead with re-unlocking the bootloader and flashing recovery/roms?
BrahManty said:
Strange, re-locking the bootloader was all I needed to get the RUU to update in my bootloader. No one else said to do that in any of the instructions, but I did it and immediately it started updating with the PH98IMG that I was originally trying to flash (from here: http://forum.xda-developers.com/showpost.php?p=38527788&postcount=745&nocache=1&z=1965375486761331).
I'm back to stock now, but firmware is 4.03.605.2, not 4.03.605.14. Is that going to be an issue or can I go right ahead with re-unlocking the bootloader and flashing recovery/roms?
Click to expand...
Click to collapse
Well, I have some good news and bad news...
Bad news is you are now on a leaked firmware and will have to S-OFF to go up or down in versions unless a full RUU is released for the current OTA of 4.5.605.14...
Good news is you are the global leak, and you can use the JuopunutBear S-OFF exploit from http://unlimited.io/index.htm just as if you were on the original ICS release. Also, you can S-OFF and use most ROMs and recoveries as you are now on a global mode firmware.
acejavelin said:
Well, I have some good news and bad news...
Bad news is you are now on a leaked firmware and will have to S-OFF to go up or down in versions unless a full RUU is released for the current OTA of 4.5.605.14...
Good news is you are the global leak, and you can use the JuopunutBear S-OFF exploit from http://unlimited.io/index.htm just as if you were on the original ICS release. Also, you can S-OFF and use most ROMs and recoveries as you are now on a global mode firmware.
Click to expand...
Click to collapse
Lol, all right, I would have tried to get the right firmware on there but my phone got so buggy that it wouldn't even boot into the rom anymore. So I couldn't get it on the SD card and I had to make do with what I had on there. At this point, I'm just glad the phone is usable again and I might leave it stock for a while. Thank you so much for all your help, I couldn't have figured this out without you!
BrahManty said:
Lol, all right, I would have tried to get the right firmware on there but my phone got so buggy that it wouldn't even boot into the rom anymore. So I couldn't get it on the SD card and I had to make do with what I had on there. At this point, I'm just glad the phone is usable again and I might leave it stock for a while. Thank you so much for all your help, I couldn't have figured this out without you!
Click to expand...
Click to collapse
Cool, glad you got it working.
That firmware is actually pretty decent and rock solid stable, you shouldn't have any more software related issues... Plus you can root/ROM like normal from that version, the radios may be slightler lower than most recommended versions, but they should work fine. If you do decide to go the ROM route again, I would suggest going S-OFF before starting, it will just make it easier in the long run.
Hey, just wanted to ask some questions as a follow-up since this seems to be the most relevant (and active) thread to my issue:
Long story short, got a new (to me) Rezound. It was running CM10, from the forthnightly thread. New SIM card from Verizon and I was getting data, but the no mobile network found error. After reading the threads I could find on the error, went with the suggestion of a wipe and so I did. A few too many beers while reading thru the forums, and I did the wipe a bit too thoroughly. Now I have a no OS found, and instead of thinking I know what I'm doing I'd like to ask to make sure I understand this correctly.
Currently, the phone is S-OFF, with TWRP 2.5.0.0. It's saying I'm not rooted, but then again no OS to be rooted. The dump from my bootloader is as follows:
*** TAMPERED ***
*** LOCKED ***
VIGOR PVT SHIP S-OFF RL
HBOOT-2.28.0000
RADIO-2.23.10.0123r/2.23.10.0124r
OpenDSP-v14.6.0.7708.00.0507
eMMC-boot
Sep 20 2012, 17:40:22
Click to expand...
Click to collapse
After checking this thread and this one here it looks like the following applies:
* I can just run the regular RUU (executable) to load a stock image without having to revert back to S-ON first.
* I will have to re-unlock the bootloader thru htcdev after RUUing
* I'll need to reinstall TWRP
Is this right? Am I missing anything?
JoeKamel said:
Hey, just wanted to ask some questions as a follow-up since this seems to be the most relevant (and active) thread to my issue:
Long story short, got a new (to me) Rezound. It was running CM10, from the forthnightly thread. New SIM card from Verizon and I was getting data, but the no mobile network found error. After reading the threads I could find on the error, went with the suggestion of a wipe and so I did. A few too many beers while reading thru the forums, and I did the wipe a bit too thoroughly. Now I have a no OS found, and instead of thinking I know what I'm doing I'd like to ask to make sure I understand this correctly.
Currently, the phone is S-OFF, with TWRP 2.5.0.0. It's saying I'm not rooted, but then again no OS to be rooted. The dump from my bootloader is as follows:
After checking this thread and this one here it looks like the following applies:
* I can just run the regular RUU (executable) to load a stock image without having to revert back to S-ON first.
* I will have to re-unlock the bootloader thru htcdev after RUUing
* I'll need to reinstall TWRP
Is this right? Am I missing anything?
Click to expand...
Click to collapse
You should be able to just boot into twrp and flash a rom
Sent from my ADR6425LVW using xda premium
izzaeroth said:
You should be able to just boot into twrp and flash a rom
Click to expand...
Click to collapse
Okay, that's good to know. For now though, if I just wanted to get my phone working, make sure there's not a SIM issue and such I could go back to a stock image without worrying? I just would rather do a lot more reading and make sure I understand what I'm doing before I try to put a rom on and screw things up further.
JoeKamel said:
Okay, that's good to know. For now though, if I just wanted to get my phone working, make sure there's not a SIM issue and such I could go back to a stock image without worrying? I just would rather do a lot more reading and make sure I understand what I'm doing before I try to put a rom on and screw things up further.
Click to expand...
Click to collapse
No doubt its good to be cautious when you are s-off. If you are just wanting plain jane stock then you could just flash a ruu from boot loader.
Sent from my ADR6425LVW using xda premium
izzaeroth said:
No doubt its good to be cautious when you are s-off. If you are just wanting plain jane stock then you could just flash a ruu from boot loader.
Click to expand...
Click to collapse
Okay, so if I go with the image here: http://forum.xda-developers.com/showpost.php?p=38527788&postcount=745&nocache=1&z=1965375486761331
Would I still need to relock the bootloader since I'm S-OFF or can I just flash that from TWRP and go from there?
JoeKamel said:
Okay, so if I go with the image here: http://forum.xda-developers.com/showpost.php?p=38527788&postcount=745&nocache=1&z=1965375486761331
Would I still need to relock the bootloader since I'm S-OFF or can I just flash that from TWRP and go from there?
Click to expand...
Click to collapse
Honestly I don't remember if you would have to relock to flash that in boot loader sine you are s-off, but I do know it won't flash from recovery
Sent from my ADR6425LVW using xda premium
izzaeroth said:
Honestly I don't remember if you would have to relock to flash that in boot loader sine you are s-off, but I do know it won't flash from recovery
Click to expand...
Click to collapse
Recovery as in HBoot or TWRP? Because I still have TWRP. I can get the windows executable RUU for ICS if need be.
JoeKamel said:
Recovery as in HBoot or TWRP? Because I still have TWRP. I can get the windows executable RUU for ICS if need be.
Click to expand...
Click to collapse
Recovery = twrp
Sent from my ADR6425LVW using xda premium
izzaeroth said:
Honestly I don't remember if you would have to relock to flash that in boot loader sine you are s-off, but I do know it won't flash from recovery
Sent from my ADR6425LVW using xda premium
Click to expand...
Click to collapse
S-off is S-off... installing a RUU wont change that, it may set you back to 'Locked", but you are S-off so it doesn't matter, you can stay locked&s-off and its no different than unlocked/S-off.
If you are going back to stock and are S-off I would use the Global Mode Leak (4.3.605.2) available on AndroidPolice and flash in Hboot... rename file to PH98IMG.zip and place in root of SD card (how it gets there is a irrelevant) then reboot into Hboot, confirm and wait.
Sent from my HTC Aria (Liberty) running CM 7.2 using xda app-developers app