[GT-I9300] Wifi Connected - No Internet issue (Solved!) - Galaxy S III Q&A, Help & Troubleshooting

Hi All,
After recently updating to stock Jellybean 4.1.1 I started having an issue with my wifi where it would appear as connected to the AP but not able to access the internet. This was intermitting. Every now and again it would work for a bit and then stop.
It appears to be a common problem on this device.
I managed to solve mine by doing a hard factory reset a couple of times... The steps I followed : (Obviously backup all your stuff first).
1. Factory Reset through the settings menu (Erase Everything)
2. Cache Wipe (Hold down vol-down+home+ power) and select wipe cache
3. Factory reset through boot menu (same menu as 2.)
4. Restart device
5. Final factory reset through settings menu again.
I have ready somewhere that the JB update left some of the files on the device in a bit of a nasty state, so multiple factory resets puts things back to how it should be.
Thanks.

can't find wipe cache option. it says download mode. don't turn off system, something like this

remove cable i think if its in ... have u installed rom manager ? clockworkmanager ?
Sent from my GT-I9300 using xda app-developers app

Had clock work manager
After ota it is gone
Sent from my GT-I9300 using xda app-developers app

swapniltiwari said:
Had clock work manager
After ota it is gone
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Volume UP+ home+ power to enter recovery.
Volume down+ home+ power takes you to download mode.
Sent from my GT-I9300 using xda app-developers app

nopes,
not working. I just did the whole procedure still, its no good.
HELP!!

swapniltiwari said:
nopes,
not working. I just did the whole procedure still, its no good.
HELP!!
Click to expand...
Click to collapse
Have you set a Static ip on the phone?

tried that too..
Not working.

open rom manager and click reboot in recovery
Sent from my GT-I9300 using xda app-developers app

Omg. Recently i'm having the same problem. I am a new user of GS3, unroot and locked, totally stock Jellybean 4.1.1 International version.
My phone connected to the home wireless but the is no data transfer occurred. Any idea why? Tried with forget the network and rejoin / put a static ip, but didn't work.
It solved when i restarted the modem, but i don't think it's the modem, because my 2 android tabs and pc's are working.
Any help would be grateful.

Wifi not working
Unable to connect wifi pls help....
error : saved secured

ezhilmxlock said:
Unable to connect wifi pls help....
error : saved secured
Click to expand...
Click to collapse
You have replied to a thread over a year old and with a solved tag. You need to open your own one with info for someone to help you.

Darke5tShad0w said:
You have replied to a thread over a year old and with a solved tag. You need to open your own one with info for someone to help you.
Click to expand...
Click to collapse
+1

Related

[Q] Help! freezed Motoblur HOME and no other launcher

Dear all,
This is the first time I have use an android device, and I have search many forums with no solution. So, thanks for everyone's time in helping me out.
1) I have root the Atrix.
2) I install Bloat Freezer from the market.
3) Install GoLauncher from market.
4) I freeze the 'home' app or system process (I'm not sure what term to use) using the bloat freezer.
Everything was fine. Untill, I decided to give this phone to my sister and from the phone instruction, I need to erase everything to factory default in order to get rid of my market account (no sure if this is the only option, but that's what the phone reflect when I try to delete my account). then, I
1) go the settings > privacy and run the reset factory default.
2) Did not defrost the 'home' app.
After the phone get back to factory default, I manage to get back to the initial stage of Motoblur setup. After setting up, the funny thing comes. There is only blank screen with a notification bar and nothing else. The lockscreen still works and double tap on the home button startup browser and hold on the search button goes to voice command. So I think the phone works, but without the GUI.
My so call solution,
The bloat freezer developer is very nice to send me an apk to defrost everything I had freeze. So,
1) I need to install the apk without the GUI. ( I found a way which not sure if works, by using a software to sideload using PC.
2) Using a Update.zip to install the apk (which I seriously don't know how to do it as I am just starting to use android)
3) Any way to defrost using adb (which also requires USB debugging enable).
Problem: I can only do it with USB debugging enable. Which is impossible as the phone is freshly reset and I cannot enable the USB debugging using the phone without a GUI.
Help:
Is there anyone who knows how to enable the USB debugging without using the phone?
Or direct me to settings using any shortcuts?
Or any other solutions? Flashing the sbf is my last resort.
Hope my explanation of my problem is clear and thanks to everyone who has view this thread and try to help me or give me suggestion.
Flash a fresh sbf, instructions and files are in the dev forum, I'd give you a link if I wasn't on my phone
Sent from my MB860 using XDA App
exume said:
Flash a fresh sbf, instructions and files are in the dev forum, I'd give you a link if I wasn't on my phone
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
Thank you for your advise. I saw the thread in flashing sbf. but this is my last resort or is this my only option? I really hope not. First time using android, flashing sbf is kind of a big step for me
wait!!1 don't flash!!! hold down home button to bring up latest apps and click on blotware freezer and unfreeze it
ethantarheels123 said:
wait!!1 don't flash!!! hold down home button to bring up latest apps and click on blotware freezer and unfreeze it
Click to expand...
Click to collapse
Unfortuanately, I reset to factory default makes the app not there anymore. So the only to defrost is the apk from the Bloatware freezer developer.
If you already did a reset and you don't have anything on the phone I would just do the sbf since you don't have anything to lose.
Sent from my Xoom using XDA Premium App
At last, I flashed the SBF... Sadly....
zakiva21 said:
At last, I flashed the SBF... Sadly....
Click to expand...
Click to collapse
In the future (hopefully it won't happen again) you can log into your market account on a computer and download any old launcher. It will be pushed to your phone and from there you can then unfreeze your prefered launcher and swith back to it.
Sent from my MB860 using Tapatalk
I have the same problem, only early stage.
I just rooted my phone, for the first time, installed Bloat Freezer, Froze Moto Blur HOME which has caused an error which I can’t get passed to fix and unfreeze.
The error states Sorry, the application home process has stopped working. Please try again. Force Close.
So, what is the easiest way to fix this without going too far down the rabbit hole?
That said my disgust with Moto Blur has got me this far, I’m sure it could take me further.
Thanks for your help.

HELP :D

Hi everyone, this is my 2nd post on the forum because it is very urgent. When i press the power button and my phone goes into sleep i notice after about 5-20 minutes the screen blinks and everytime it blinks and i wake the phone and try to turn on my wifi it shows up with wifi "error" . i am looking for a permanent solution.
What i tried :
1) restarting phone (works short term)
2) typing *#*#526#*#* in keypad (works short term)
3) Wifi policy set to "never" (had no effect)
4) FXR WIFI FIXER app (had no effect)
5) battery pull (no effect)
6) static ip (no effect)
7) factory reset/ new rom (no effect)
So can anyone help me with this It started when i was using kph 2.3.4 and now i use kpe 2.3.3.
Please reply any help would be appreciated
what rom are you using? rooted or no?
if possible go to cwm / or stock revoery
enter by shutting down phone
- then press power and middle button together for about 20seconds(?)
-press down button to format
-press middle
-wait
-done
-your phone is formatted and fixed hopefully
I already said!
tohno said:
what rom are you using? rooted or no?
if possible go to cwm / or stock revoery
enter by shutting down phone
- then press power and middle button together for about 20seconds(?)
-press down button to format
-press middle
-wait
-done
-your phone is formatted and fixed hopefully
Click to expand...
Click to collapse
i already said i tried factory reset and i said that i was using 2.3.3 kpe.. Thanks for the reply though any help?
Thepizzaguy97 said:
i already said i tried factory reset and i said that i was using 2.3.3 kpe.. Thanks for the reply though any help?
Click to expand...
Click to collapse
Try reflashing with odin.
If it doesn't work, well service center is your only solution.
TeamCooper Developer
I had the same problem about wifi error... I would use that code
Agreed short term success
But then I flashed a cm7 ROM and it works like a charm
-------------
May The Force Be With You
jumbobombo said:
I had the same problem about wifi error... I would use that code
Agreed short term success
But then I flashed a cm7 ROM and it works like a charm
-------------
May The Force Be With You
Click to expand...
Click to collapse
Thanks for the reply, btw how is the camera quality on cm7?
Thanks!
Thepizzaguy97 said:
Thanks for the reply, btw how is the camera quality on cm7?
Thanks!
Click to expand...
Click to collapse
Camera quality is good in Cm7..
Don't just say thanx click on the thanx button
Cameras good same as the stock
Modding the phone doesn't change its hardware
-------------
May The Force Be With You
Lol , thanx is my signature and I will click thanks
Thanks!

MDM locked S III

UNIT : Samsung SIII SHV - E210S
Problem:
1. Camera, when you clicked on camera it shuts down and says "Security Policy resrticts the use of Camera"
2. Memory Card - Micro SD is mounted but when booted you can't see the icon on My Files also you can't browse the contents of the memory card but when in download mode / restore mode it reads it.
3. Bluetooth - Icon or setting is there but when you click it on it does not turn into green or won't turn on.
4. On the Drop down menu there's a notification that says "Please install MDM" - i tried installing MDM but when the app is installed it prompts for a "company site code"
Possible Solutions that already tried
1. Restored the phone to it's original state on Device Recovery Mode (Factory Reset) nothing happened
2. Flashed a custom rom (OCHIE ROM) but still the "Please install MDM" on the drop down prompts it and same issues, Cam+MMC+BT restricted
3. Flashed custom kernel (Berzebb), nothing happened "Please install MDM" on the drop down prompts it and same issues, Cam+MMC+BT restricted
4. Tried to locate the Application that restricts the use of the following features by using Titanium Backup PRO and was able to locate 1 app that says DM manager, tried to kill the app using Titanium backup and was able to remove the notification "Please install MDM" on the drop down menu but still same problem Cam+MMC+BT restricted.
** Anyone who can suggest remedies please post on this thread. you're reply would be greatly appreciated. Thank you very much.
Currently I have these settings:
Software number: 4.1.2
Kernel version: 3.0.72-Berrzebb-SGS3-JB-1.8
Baseband version: E210SKSMD2
Build number: JZO54K.E210SKSJMF1
You are posting in the wrong forum, anything you try from this one may brick your phone.
boomboomer said:
You are posting in the wrong forum, anything you try from this one may brick your phone.
Click to expand...
Click to collapse
okay i do understand. my apologies. kindly disregard.. thank you
Haven't you tried stock rom?
Sent from my GT-I8552 using xda app-developers app
boomboomer said:
You are posting in the wrong forum, anything you try from this one may brick your phone.
Click to expand...
Click to collapse
Might not be see posts in General section one of the models that belongs nowhere .
http://forum.xda-developers.com/showthread.php?t=1749214
jje

cant connect to camera error

Hi Guys pls help
Last 6 to 7 months i have been using different custom roms for my a116 ...camera was working fine...since last week am getting this wierd error "cant connect to camera" and sometimes unfortunately gallery has stopped .. i have tried factory reset , deleting dcim folder , install a 3 rd party cam app , reflash couple of other roms, flashed back stock 4.2.1 yet the same error...sometimes camera opens but all i see is green screen
does anyone know a fix for this or what is causing thjis ? right now i am on stock 4.2.1
karthik_sa2 said:
Hi Guys pls help
Last 6 to 7 months i have been using different custom roms for my a116 ...camera was working fine...since last week am getting this wierd error "cant connect to camera" and sometimes unfortunately gallery has stopped .. i have tried factory reset , deleting dcim folder , install a 3 rd party cam app , reflash couple of other roms, flashed back stock 4.2.1 yet the same error...sometimes camera opens but all i see is green screen
does anyone know a fix for this or what is causing thjis ? right now i am on stock 4.2.1
Click to expand...
Click to collapse
Power off the device, press vol up+vol down + power buttons. when it appears, press vol down for factory mode. Inside unit tests, test the camera. If it still doesn't work, get your phone to a service center.
SaketJoshi said:
Power off the device, press vol up+vol down + power buttons. when it appears, press vol down for factory mode. Inside unit tests, test the camera. If it still doesn't work, get your phone to a service center.
Click to expand...
Click to collapse
Thank you so much for the reply buddy.. In factory mode it is working fine. What could be the problem then??
karthik_sa2 said:
Thank you so much for the reply buddy.. In factory mode it is working fine. What could be the problem then??
Click to expand...
Click to collapse
You said you reflashed stock, how? From a zip or sptools?
Try installing from sptools
Sent from my Micromax A116i using xda app-developers app
SaketJoshi said:
You said you reflashed stock, how? From a zip or sptools?
Try installing from sptools
Sent from my Micromax A116i using xda app-developers app
Click to expand...
Click to collapse
flashed stock by sptools only buddy

Help please, after upgrade i cannot unlock my honor5x

Hi,
this morning i upgraded OTA from KIW-L21C432B340 to KIW-L21C432B350.
After the final Reboot i typed in the pins of the 2 sims and then was asked to unlock the phone.
When i click into that field, no keyboard is shown. I also tried a touchpen.
I am not able to enter the unlock-password, what can i do?
Best Regards,
harleymk2
harleymk2 said:
Hi,
this morning i upgraded OTA from KIW-L21C432B340 to KIW-L21C432B350.
After the final Reboot i typed in the pins of the 2 sims and then was asked to unlock the phone.
When i click into that field, no keyboard is shown. I also tried a touchpen.
I am not able to enter the unlock-password, what can i do?
Best Regards,
harleymk2
Click to expand...
Click to collapse
Turn off your phone, press and hold power + vol up and choose factory reset from the menu if you are not concerned about the data.
or if you are so concerned about your data, just push a 3rd party keyborad through adb,
but id recomend doing a factory reset, after trying the above method
but he cant enable the keyboard after it is installed by adb
True I skipped a KIW-L21C432B350 update of almost 200mb I recommend updating, I jump via OTA, everything perfect I'm doing everything right
PeKeT said:
True I skipped a KIW-L21C432B350 update of almost 200mb I recommend updating, I jump via OTA, everything perfect I'm doing everything right
Click to expand...
Click to collapse
Hello
At first sorry for off topic.
Did you use otg patch? If yes is it working after updating? I have tried to patch my b350 but it wasnt succes.
harleymk2 said:
Hi,
this morning i upgraded OTA from KIW-L21C432B340 to KIW-L21C432B350.
After the final Reboot i typed in the pins of the 2 sims and then was asked to unlock the phone.
When i click into that field, no keyboard is shown. I also tried a touchpen.
I am not able to enter the unlock-password, what can i do?
Best Regards,
harleymk2
Click to expand...
Click to collapse
Guys! .
he have issue with the keyboard app crashed or not functioning after update ! ..
boos u can try to search for flashable keyboard app throw recovery it should work now ! but u just try to wipe factory rest and check if will work then do my steps !.
A factory reset is the better option.

Categories

Resources