Related
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
Does anyone have experience with this case? I know it covers the mic (I plan to drill a little hole).
I just received mine today and I must say I'm very impressed by the quality of the mold they used. Meterial seems top notch. Love this case so far, they also included the new screen protector which is a plus. Ill get pictures up ASAP. I would definetly recommend this case to anyone with an s2.
Sent from my SAMSUNG-SGH-I777 using xda premium
Pictures would be great! I also have a white one on the way, hopefully as I placed an order over the weekend. I intended on modding the thing to get rid/fill in the antenna hole if I ever find the time, too (or find out if it really bothers me that much).
Ok, whats the deal with the corner cutout? I've seen this on several different cases. Does the international version have some sort of pullout antenna?
Case looks nice and classy but for what they are charging they should be offering a case that's specific to the AT&T model.
I recall reading that the corner cutouts are originally for Korean model phones. The antenna was in that area for those phones.
I really like it. It's a nice mix of hard and soft materials. It's flexible, which is nice because it makes removing the case fairly easy (for those of you who want to access the phone's back cover to hot swap batteries).
For the most part, the case feels pretty smooth, which makes getting it out of the pocket an easy process (I previously used the casemate pop case and the rubber sides made it fairly annoying to pull the phone out of the pocket). The case definitely adds more grip to the phone, but overall, it still is a little bit on the slippery side. On the continuum of "slippery vs. grippy" I'd say it's a pretty good balance, but I wouldn't mind it being a little more grippy.
Even though the case is made for the international GS2, it still fits well on the AT&T SG2. The noise-cancelling mic is covered by the case, but I have not had any problems as a result of this. However, you might come into problems if you are trying to use the phone in a noisy environment. I'm a little bothered by the corner cutout for the antennae (for the international SG2) since it really leaves that corner unprotected if the phone happened to fall right on that corner. Then again, i'm just going to take my chances that i'm not going to drop my phone on that exact corner.
The case still keeps the phone very thin and sleek. Also, the case has these tiny sparkle dots that show up on the back of the case, which give off a cool effect when reflecting light. Some may say, they make the case look a little feminine, but I personally don't think they do. In all honesty, you can't even really notice them unless you look close at the case and in the right lighting.
I got the yellow ultra capsule. I've heard one person say that these cases are prone for showing up finger smudges, but at least with my yellow one, finger smudges have not been a problem.
The case covers the volume and power keys. They are still pressable and work fine, but the buttons aren't as sensitive as they are without the case. However, this difference is really negligible for me. Overall, hardware buttons work fine.
I really liked the Body Glove Mirage cases that were made for the Samsung Captivate and the Infuse. In my opinion, this case is just as good as those cases.
can you guys post some pictures? want to see how much it adds to the thickness of the phone.
it does look good from their website though..
Sorry on the delay for the pictures guys, let me know if you need any certain perspectives on some more pictures.
djoutrages said:
Sorry on the delay for the pictures guys, let me know if you need any certain perspectives on some more pictures.
Click to expand...
Click to collapse
what does the unprotected corner look like with that case?
today i checked my s3, i found this the paint of my inside screen "back" key peeling off near the border inside the gorilla glass, its really faint but if u look close u can see it, i heard samsung have problem with the blue version but my gs3 is only 2 weeks old, never feel, so far only thing it could get there is a raindrop.
anyone else here experience something similar? was trying to get picture but its really thin hard to notice.
i dont think warranty will cover it, especially since i root it, and its perfectly working phone. sadly in a year when i can sell it probably going to lose more paint.
I feel your pain bro imperfections bug the hell out a me because once you notice it your always looking at it , I've had no issues with my pebble blue beast yet but this is my second one in 2 weeks the first one I messed up flashing modems anyway phone the store and tell them there's a problem with your phone when trying to answer calls that's what I did ten days after buying mine , and see if they will exchange it , if yes just wipe binary factory reset and take that ***** back , at the end of the day its a £500 pound smartphone if your not happy you should be able to return or exchange it , I'd go to the shop and make them exchange it or else : ) good luck don't waste time
Sent from my GT-I9300 using xda premium
jgalvez21 said:
today i checked my s3, i found this the paint of my inside screen "back" key peeling off near the border inside the gorilla glass, its really faint but if u look close u can see it, i heard samsung have problem with the blue version but my gs3 is only 2 weeks old, never feel, so far only thing it could get there is a raindrop.
anyone else here experience something similar? was trying to get picture but its really thin hard to notice.
i dont think warranty will cover it, especially since i root it, and its perfectly working phone. sadly in a year when i can sell it probably going to lose more paint.
Click to expand...
Click to collapse
Do you have a screen protector? I have the pebble blue with a screen protector and haven't noticed anything.
mattn95 said:
Do you have a screen protector? I have the pebble blue with a screen protector and haven't noticed anything.
Click to expand...
Click to collapse
no, but the peeling was inside the screen and it looks really over the thin border... i have only 2 weeks with the phone.
i got it on contract on claro, and i doubt they going to exchange it over something so small as paint :/
i looked in AT&T gs3 forums and pretty similar to the border chrome peeling off issue :/, like my n82 eventually it all wear off with time.
The only reason there were launch delays for the SGS3 were because of the pebble blue version even though they are made of the same material you can look closely that they have a difference with the white version in the feel of your palm. Manufacturer's are having a crisis in the pebble blue department that's why I took the white one instead.
jgalvez21 said:
no, but the peeling was inside the screen and it looks really over the thin border... i have only 2 weeks with the phone.
i got it on contract on claro, and i doubt they going to exchange it over something so small as paint :/
i looked in AT&T gs3 forums and pretty similar to the border chrome peeling off issue :/, like my n82 eventually it all wear off with time.
Click to expand...
Click to collapse
Just unroot/triangle away and return to store. Its worth a try.
I'm using a TPU case with screen protector since day 1 as always. No problem.
Okay I can't say that I own a s3 but with Samsung phones in general I can tell you this. My Samsung impression(dinosaur) had the same problem. After awhile the paint was coming off chipping and all that. Its just what Samsung uses I suppose just had to put my two sense in
Sent from my Inspire 4G using xda premium
as I post on the other threat
My top left hand corner stainless steel paint peel off. my phone in the protective case first day! I don't even till I was shopping for extra case, remove it and there it is black color!
Do you guys think they exchange another one for me?
Can we see some images?
No case/protector here since day 1. Phone is about a month and half old. As good as new, no paint peel, no scratch/crack on its own.
would be hard to get a picture, its really small but its pretty much blue paint peeling from the lighter blue border, it looks black below. its really faint,i dont touch it so it doesnt remove more paint
i going to ask tomorow but i doubt it, they gotta replace it.
if not, i guess i will have to order online a protector. but even n82 took a while for the paint to peel, this took 2 weeks.
I have been using mine with no protection at all for a few weeks now and have not had any issues- blue s3
Sent from my GT-I9300 using Tapatalk 2
As title states. I want a TPU case that is as clear as possible from the product. I was going to go a hard crystal case which are obviously extremely xlear but they just don't have the same shock properties.
The best I can find so far is the poetic which can be found here but I seriously HATE the fact you can't see the sexy red border because it is hidden behind the grey on that case.
I dare say they had to use a different material for the border for maximised button pressing or something. Either way, it is the closest I can find but not perfect. Anybody have any ideas? (preferably without that stupid S design)
I just got this one last week and so far I like it a lot. The sides are clear with a rough texture. You can see the red stripes through it and the back has a nice X design. No branding to mar it. It takes a couple of weeks, the boat from China is way slow!
drowe said:
I just got this one last week and so far I like it a lot. The sides are clear with a rough texture. You can see the red stripes through it and the back has a nice X design. No branding to mar it. It takes a couple of weeks, the boat from China is way slow!
Click to expand...
Click to collapse
I had two of these for my One X and didn't like the fit and finish. They kept lifting my screen protector. Maybe the quality has improved...
EDIT: Nevermind. Didn't read.
hi as many note 3 users know, the plastic side frame is easy to get damaged, i have few cracks and one line just under the main power button (not sure just facial or completely crack?)
so, how easy is to change and which one i have to buy ? - im quite noob in hardware sides.
Sure you can buy one on Ebay
I have the same problem, the silver plastic bezel is very fragile.
If you search in Ebay you can found the Bezel and some of them come with tools to turn this in a complete DIY.
Actually i found all the body for this phone in ebay, so you can turn your used and damaged note 3 into a "brand new" one.
Thanks 4 the info. Where did you find it. Could you please share the link?
Thx in advance
hey guys.here is a link for the bezel replacement Bezel On EBAY
i want to tell you that it's not that easy to change it as you need to move the lcd screen from the one bezel to the other one.
there is glue between the lcd and the bezel so you need to warm it and remove it really carefully.i did the process yesterday on my note 3 and it was a pain in the a$$ so i have to tell you to be carefull before any move you re going to do.
Any link for Indian note 3?
Sent from my SM-N900 using XDA Free mobile app
I considered doing this, as I was given a note 3 a while back, but the bezel is beat to hell and the screen had a minor crack. I should've replaced both at the same time, but the small crack turned into a large one and needed immediate attention It's covered by a case now anyway though, so it's not much of an issue anymore.
I dropped mine a while ago and put some pretty nasty scratches on the bezel.
I ended up sanding all the plastic chrome plating off down to the white plastic underneath.
covered the screen with electrical tape and ran a razor round the edge (so I could get to the front part)
It actually looks really good, I prefer it to the chrome.
I got a cheapo battery cover off ebay aswell in orange and it looks real good,
Its a tough job!!!
got my Note 3 as a gift from a friend who cracked it. I replaced the entire Display (along with frame)
and 3 days later I dropped it and got scratches in the frame.
so I decided to buy a frame and fix but its really a tough job.
so I got a bumper for 3$ and job done
I have installed one of those here http://www.ebay.com/itm/Thin-Aluminum-Metal-Bumper-Case-Cover-For-Samsung-Galaxy-Note-3-III-N9000-N9005/151251742076?_trksid=p2045573.c100033.m2042&_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D31478%26meid%3D341538ef5e9d4d6da3228a5f902e8cf1%26pid%3D100033%26rk%3D1%26rkt%3D4%26mehot%3Dpp%26sd%3D151251742076
There are some more nicer ones our there, however this does the job well and the build quality is goodd too, my first one at 1,30 USD was not worth anything.
thanks i thought i saw same one for bit less than that, will browse ebay later.
maskerwsk said:
I dropped mine a while ago and put some pretty nasty scratches on the bezel.
I ended up sanding all the plastic chrome plating off down to the white plastic underneath.
covered the screen with electrical tape and ran a razor round the edge (so I could get to the front part)
It actually looks really good, I prefer it to the chrome.
I got a cheapo battery cover off ebay aswell in orange and it looks real good,
Click to expand...
Click to collapse
Photos plz
Up! I'm interested too.
yes i just remember i have some sand paper at home please post photo and detailed instructions... cheers
rockbastard said:
I have installed one of those here http://www.ebay.com/itm/Thin-Alumin...id=100033&rk=1&rkt=4&mehot=pp&sd=151251742076
There are some more nicer ones our there, however this does the job well and the build quality is goodd too, my first one at 1,30 USD was not worth anything.
Click to expand...
Click to collapse
Hows the reception with this frame on it? Bc in the past i bought a cheap one that folds over the original side bezel but reception dropped a lil bit.
triad88 said:
Hows the reception with this frame on it? Bc in the past i bought a cheap one that folds over the original side bezel but reception dropped a lil bit.
Click to expand...
Click to collapse
I haven't noticed any drop in reception at all
rockbastard said:
I haven't noticed any drop in reception at all
Click to expand...
Click to collapse
because you must be either living in the area where your carrier signal is real strong/good, or you dont pay attention to little details, otherwise you're lying
I have tried handful of those and other plastic metalized/mirror painted bumpers and what not and all to one had some impact, especially those which had metalized paint/metal/aluminium back cover.
Simple speed test will tell alot when wearing the cover, or just go and keep an eye on your signal strength meter. It sure as hell affects signal.
mine Note 3 is banged up pretty bad around the bezel but instead I just figured it would be more practical getting some slim neat bumpers and call it a day. not only hiding worn and tired bezel but also protecting the screen and back camera optics to some degree
some of my past purchases that proven to be good investment:
BLACK - http://www.ebay.com/itm/371686423462
BLACK - http://www.ebay.com/itm/331859225625
http://www.ebay.com/itm/271911899853
http://www.ebay.com/itm/391289113353
http://www.ebay.com/itm/151139101488
http://www.ebay.com/itm/181701505005
http://www.ebay.com/itm/182354407036
http://www.ebay.com/itm/311580942819
just thought I will share...
Mr.Ultimate said:
because you must be either living in the area where your carrier signal is real strong/good, or you dont pay attention to little details, otherwise you're lying
I have tried handful of those and other plastic metalized/mirror painted bumpers and what not and all to one had some impact, especially those which had metalized paint/metal/aluminium back cover.
Simple speed test will tell alot when wearing the cover, or just go and keep an eye on your signal strength meter. It sure as hell affects signal.
mine Note 3 is banged up pretty bad around the bezel but instead I just figured it would be more practical getting some slim neat bumpers and call it a day. not only hiding worn and tired bezel but also protecting the screen and back camera optics to some degree
some of my past purchases that proven to be good investment:
BLACK - http://www.ebay.com/itm/371686423462
BLACK - http://www.ebay.com/itm/331859225625
http://www.ebay.com/itm/271911899853
http://www.ebay.com/itm/391289113353
http://www.ebay.com/itm/151139101488
http://www.ebay.com/itm/181701505005
http://www.ebay.com/itm/182354407036
http://www.ebay.com/itm/311580942819
just thought I will share...
Click to expand...
Click to collapse
you have a lot of cases!
erwinsie said:
you have a lot of cases!
Click to expand...
Click to collapse
little too many ... beware that those wooden cases are the coolest thing your phone can get but if you do drop your phone they crack and break apart sometimes... not always though but alot alot sooner than any plastic case would and thats a heartbreaking thing because there not exactly cheap case, but hey - how often does someones phone feels and smells like real fresh quality piece of wood? I like them wooden ones very much even if they crack and put some tax on my pocket at the end of the day its almost like your personal signature of style ... besides, its always warm to touch and zero signal interference
PS: lots more were thrown out many months ago, especially all those metalized ones, no use to me nor could I offer them to anyone I knew who had note 3 due to what they are
When my display was damaged, it got repaired, not only the glass, but the whole display including the bezel, it was 1 piece.. I guess it's very hard to replace only the bezel