Related
Hello guys,
I need advice on whether I should dismantle my Blackstone, or should I just leave it to the pro? I want to change the housing as the current one's badly damaged but I dont want to pay big bucks for that.
As for myself, I have fair knowledge on these stuffs, as I have dismantled my previous HTC phones, ipods etc etc. However, the last time I tried to change the antenna cover of my Blackstone, I felt that it was rather difficult compared to the previous phones/devices I did. I ended up breaking the connecting latches on the old antenna cover. And I did follow the HTC Service Guide, which I think is not sufficient.
I couldn't find any video tutorials on dismantling the Blackstone. Could someone point me in the right direction please? Thanks a million
I just had to replace a damaged digitizer. i downloaded the service manual and it did help......a little! Basically, the main dissasembly was pretty straight forward, but the digitizer replacement was a nightmare!!! The LCD, Digitizer and front housing are basically fused together with an adhesive tape. Trying to remove the LCD from the digitizer was futile (broke the LCD). I had to basically replace the LCD and the Digitizer to make it all work again. The main problem with the new hardware is that you cannot get the stock replacement adhesive/tape so i had to use stuff from around the house.....i hope the diplay doesn't fall out of my phone. Anyway, got it eventualy working. Definately doable....but be careful not to touch the digitizer or LCD with your fingers.....whooops! Anyway, good luck.
swolkat said:
I just had to replace a damaged digitizer. i downloaded the service manual and it did help......a little! Basically, the main dissasembly was pretty straight forward, but the digitizer replacement was a nightmare!!! The LCD, Digitizer and front housing are basically fused together with an adhesive tape. Trying to remove the LCD from the digitizer was futile (broke the LCD). I had to basically replace the LCD and the Digitizer to make it all work again. The main problem with the new hardware is that you cannot get the stock replacement adhesive/tape so i had to use stuff from around the house.....i hope the diplay doesn't fall out of my phone. Anyway, got it eventualy working. Definately doable....but be careful not to touch the digitizer or LCD with your fingers.....whooops! Anyway, good luck.
Click to expand...
Click to collapse
Thanks.
Hmm. Or maybe the problem was only me. I find it pretty hard to dig out the antenna cover from its latches. Maybe I was digging on the wrong spot. And thats why I was reluctant to continue further. Mind sharing how you "digged" the antenna cover?
Yeah, be careful with separating the LCD from the digitizer. I recently replaced the digitizer on mine. I agree with the antenna cover, I had some troubles with mine.
I used a old sim card to help pry the antennae cover off. Because my digitizer was cracked i was able to peel it off the lcd without the the lcd. Managed to use the old adhesive tape aswell.
Check out this thread - it might help you! There you will also find a link to a video some other user made, showing how the HD can be disassembled! But - as others already have said: I wouldnt recommend disassembling the screen unit! I too managed to destroy my LCD doing so! forum.xda-developers.com/showthread.php?t=462102
Thanks alot guys. Appreciate it.
video is in my signature. Changing the antenna cover is actually really easy once you have done it ... once or twice ;-)
OliveUK said:
video is in my signature. Changing the antenna cover is actually really easy once you have done it ... once or twice ;-)
Click to expand...
Click to collapse
Hi, i also just made a couple of video - disassembly and reassembly - the inside of the HD is becoming a real star...
see
http://forum.xda-developers.com/showpost.php?p=4950742&postcount=113
Hello Guys,
i have a problem, i had already replaced the LCD-Screen because the old was broken.
But now i got a new problem... if i place the new screen on the digitalizer i got a glimer on the display. I don't now why. But i already discoverd that this effect only appearce if the LCD-Screen is on the digitalizer..
So what is the exactly reason and how can i fix this problem? Is the digitalizer cracked?
Here are 3 Pictures, one is without the digitalizer.
Thank You,
PS: Sorry for my bad english
did you try to fit digitizer in or just holding it upon the lcd?
what would happen if you rotate it 90degs?
are you sure there is no protection foil still on the lcd???
-
behind and on the lcd, there are reflection foils, bluring, light redirecting, polarizating. maybe 6 of them together. some are glued on screen, some are just below it. obviously there is something in digitizer as well, and those in your replaced lcd are not compatible with digitizer.
can you ask for return of the lcd and get another one?
the other option would be getting replacement of digitizer from the same shop.
or third, this effect doesn't look like it's from polarizator. polarizator is glued but those others are not. if it will not change if you rotate it, like with polarizator effect, means it's not polarizator and you can replace those other foils from below lcd. putting ones from your broken screen to the new one. It's quite difficult, but could be done.
okay.. if i rotate the digitalizer the effect changes..
in nearly 90 degree the effect is better than normal.. but not really good..
so is there a magnetism issue??
or whats the reason for this effect?..
could the digitalizer broken? but it's still working..
the display brokes because of violence..
could the digitalizer although broken??
no the digitizer is fine.
the replacement you get was not oem. means was not from the same factory.
someone working in there made some pictures or paintings of the lcd and showed it to his friend who owns a similar factory. He then made this lcd and sold it to you. As he didn't know what sort of, let's call them optic foils, have been used in the original he just put the ones he new were working fine with another mobile. But he didn't expect, as i am surprised too, that the digitizer have an optic foil inside as well. But before realizing, I suppose they already gave bonus to all those little workers and started overnight secret manufacture.
Before realizing the mistake, they already produced a lot of it. To cut the loses, I suppose they created a set of digitizers with a similar practice, which they would sell together with lcd and would be working good.
Now someone, your seller probably thought selling separate lcd would be ok too, so he did. That's why i was suggesting you have right to have an replacement, refund or an new digitizer from him at a fair price.
Of course don't take me too serious on the picture/painting matter, but otherwise I wouldn't be surprised if I came to true quite close
anyway those fake parts are a good quality and in most cases you wouldn't say difference. But shyt happens
as the rotating didn't solve issue completely problem would be those foils below lcd. if your seller would not be cooperative, you've got nothing to loose. open both lcds and change foils over.
Or get a fake digitizer which you would be sure is compatible with that screen.
If not successful, get a combo, lcd + digitizer.
hmm okay..
in the description is written original htc ware..
i had send my seller that problem and now we will see..
thanks a lot for those information..
I would be very interested in knowing how you got the digitizer and screen seperated? Arent they glued and most likely going to break easy?
did you mean the digitalizer and the lcd display or the front screen?
I opened one up once and the LCD appeared to be glued on to the back of the front screen (which I assume is the digitizer?)
ah okay.. eeerm.. i don't know that the lcd was glued on the digitalizer.. because my display has broken and the liquid was out of the display.. so the LCD was easy to take off..
But I've read some guys has warmed it firstly with a hair dryer and then they could take the display off..
hx4700 Killer said:
I opened one up once and the LCD appeared to be glued on to the back of the front screen (which I assume is the digitizer?)
Click to expand...
Click to collapse
you make me want to open ma rhodium.
if it's glued use a razor, or heat gun & blade like on apples.
then clean it and put new tape.
fake3 said:
ah okay.. eeerm.. i don't know that the lcd was glued on the digitalizer.. because my display has broken and the liquid was out of the display.. so the LCD was easy to take off..
But I've read some guys has warmed it firstly with a hair dryer and then they could take the display off..
Click to expand...
Click to collapse
yeah dryer is maybe more safe just keep it below 100 cels. but it's not so vulnerable on bending too.
fake3: you sure you don't have protector foil on that lcd you bought?
i been playing around and get similar efect with a protection foil below polaroid.
there was still one protection foil on the front of the lcd.. but i already removed this foil..
but can you make a picture where the foil the polaroid is??
fake3 said:
there was still one protection foil on the front of the lcd.. but i already removed this foil..
but can you make a picture where the foil the polaroid is??
Click to expand...
Click to collapse
I was playing with just a generic foils. not rhodium.
They can put filters inside plastic nowadays. and mix even more of them and it's all still tiny.
If there is one in digitizer, it would cut sun reflections of lcd and would make good sense.
Glass could be tented, too. digitizer is usually one glass and one foil.
even if you would find something glued on lcd or digitizer, it's not possible to take it of without damage. I talked to people producing foils and applying them they can't take that off too.
There have you be one polarizer glued on front of lcd, otherwise you would see nothing. And they usually gluing one on back. That make the light more efficient. redirect light in useful directions, but is not necessary, that is another possible difference in your case. And probable, because it spares $ and space. But it's glued - no help there if that's the case.
but then there are all those which are dispersing light evenly, those you can try to change. They all have to be used in a set working together they create
something called Brewster condition, if that's not met, you see something like you see on your screen. every active foil is a part of it, and obviously there is something in your digitizer.
Just had another though, there is a small chance that htc decided to change factory or producing process themselves. and both are original. But I wouldn't say that's very probable.
So guys,
i solved the problem..
I bought an new Digitalizer from the same seller and now it works fine..
Thanks a lot for the hint with the different manufractures..
Greetz
happy to hear that
no worries
guys.. i wan to ask something..
my LCD is glued to my digitizer. since both of it is broken.. i juz throw the whole part away.
but then, i diden really glue my new / replacement LCD to my digitizer.
so i assume they did have some space in between.
although my rhodium works well now, but my digitizer only able to sense fingernail o stylus only. anything a tad bigger than fingernail, it wont pick up. neither my thumb nor my finger.
is this possible due to the space in between the screen made it so? or my digitizer was some lousy quality stuff?
devalian said:
guys.. i wan to ask something..
my LCD is glued to my digitizer. since both of it is broken.. i juz throw the whole part away.
but then, i diden really glue my new / replacement LCD to my digitizer.
so i assume they did have some space in between.
although my rhodium works well now, but my digitizer only able to sense fingernail o stylus only. anything a tad bigger than fingernail, it wont pick up. neither my thumb nor my finger.
is this possible due to the space in between the screen made it so? or my digitizer was some lousy quality stuff?
Click to expand...
Click to collapse
The digitizer is a seperate part from the screen. It sends X - Y coords to the device letting it know where you pressed and the device coorelates that to what was on the screen where you pressed.
What I am saying is that you could have the two pieces seperated the screen in one place on the digitizer in another and you should still be able to press on the digitizer and have the device react appropriately.
The digitizer works independantly from the screen.
haha.. so in short.. it means by digitizer is lousy rite?
I Have de same problem, I need a new lcd screen but i dont know where buy
please help me
and i need the service manual
Thks
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
keithgrobertson said:
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
Click to expand...
Click to collapse
Try this http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/1
Or, this http://www.youtube.com/watch?v=TbR56jSplRs
Broke my digitizer and did the job myself using the youtube guide above. Just used straight up superglue to glue digitizer to frame. I put a bunch on the top and bottom and very little on the sides.
Amazingly the phone worked when i put it back together... for a while until I screwed up one of the ribbons by opening it a bunch more times. Be extra careful with these, especially the volume/camera ribbon. You can bend it pretty easily trying to slide it back into its slot.
Good luck.
NB: Theres places that will do it for as little as $90 in case you don't want to take the risk.
http://www.ubreakifix.com/
Thanks for posting the youtube link. I can't even quote the post because it involves an external link. The video was vague on details and the quality is crap but it did the trick.
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from amazon and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Metacat said:
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from ebay and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Click to expand...
Click to collapse
I replaced my digitizer, and had the EXACT same thing happen (not the light sensor but the line in the screen that doesnt respond to touch).
Get a new digitizer, but get it from someone else.
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Metacat said:
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Click to expand...
Click to collapse
No. I sold it and let someone else deal with it. Didn't have the time to replace the digitizer again. Too much of a hassle.
I just replaced a digitizer on an atrix... i didnt put any adhesive on it because there was what i thought was adhesive strips on the digitizer... but there's strips on the screen that doesnt respond, i heated it n tried reattaching the digitizer a few times n sometimes the home and back button will work, sometimes they wont... any suggestions? could the lack of adhesive cause this?
Menu buttons problem
if menu buttons is freeze till I block and then unblock my phone is it digitizer problem ?
what do you mean by " block/unblock" ?
Sent from my HTC Desire CDMA using XDA
He means lock/unlock.
Go the ifixit route!
Just went through 3 digitizers in my repair, and wanted to share my experience/caveats
I bought one digitizer from All4Cellular for $25, and the others with a 20% discount a few days later, for $20.
I installed
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Got the idea to move the LCD screen from another RepairUniverse YouTube video and a previous post here, and tried installing the digitizer from the front face of the phone. It was still a delicate matter to bend the flex cable so that it fit through the slot, and then re-position the LCD and align the sticky strips of the digitizer on the LCD and casing. Part of the digitizer worked this time - a 1cm vertical strip on the left fowled any attempt to touch icons or use a keyboard, so I thought I had damaged things again (doh!).
Hoping third time was the charm, I completely disassembled the phone using the guide in the 'ifixit' link, since a digitizer/case assembly was suggested in another thread. The rear camera just needs to be raised above the casing so the thin plate can move upward, and the LCD pops out easily if the sides of the casing are delicately pulled. The digitizer can be positioned easily and with minimal bending/twisting of the flex cables.
When reconnecting everything the third time, I noticed that pressing down on the front camera / digitizer connection *with the rubber boot in place* didn't pass when pulling the connected assembly upward. So I pulled the rubber boot out of the way and snapped the camera / digitizer connection firmly, then re-inserted the boot. A loose connection might have been the culprit for the nonfunctioning part of the digitizer in the second test.
@MrSaba - I had the same issue with capacitive buttons - perhaps because the screen senses touch and disables those buttons. Replacing the digitizer solved the issue
trouble
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
drZeT said:
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
Click to expand...
Click to collapse
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
jjwatmyself said:
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
Click to expand...
Click to collapse
The first one was with the red stripe indeed, from china. The one with a frame came from UK, "used but tested OK". original screen is gone - tore off flex cable while removing.
Well, update...
2 screens bought on eBay were BAD. Had to wait full month for authorised motorola service to change the digitizer. Must say though that both merchants on ebay refunded, no questions asked. Lessons learned - pay more, wait longer, never give up
DrJCFitz said:
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Click to expand...
Click to collapse
What I noticed on their video was that their folded digitizer connector magically unseats itself during the disassembly transition. I had to pry mine off based purely on guesswork and think I might have broken the flip-chip that is stuck onto the frame with double-sided tape. Like yours, my touchscreen doesn't respond at all, despite there being no cable tears. I'm going to try and re-heat that flip chip and maybe get the connections to work again (doubtful).
To anyone else out there attempting this... when you go to remove the touchscreen, HEAT THE CONNECTOR so that you can gently pry it out!
Bad screen I got 3 before it worked its fine now if old one partially works new one doesn't screen is junk took mine apart several times to figure out screens were junk...guess they felt sorry for me give me my money back plus free working screen.from amazon
Also that lock clamp u mentioned first video I watched didn't show unlocking that I just pulled it out and pushed back in it was the 2 screen that I figured out it needed to be pryed loose by the white clamp but guess I didn't damage it..
Sent from my HTC One X+ using xda premium
I have just put in my second digitiser. The first was one had a red stripe, which was junk, the second on I bought had the plastic round the edge and the digitiser.
I put it in and it worked fine no dead spots at all. Then 12 hours in it started to stop working intermittently. Then 24 hours after that while on charge its dead again. I reflashed notattrix and still nothing. I've confirmed all the ribbon connectors are firmly in place and everything looks right.
Any ideas whats wrong?
thanks
Jonnym
Okay, so my Terminator...errr, my son, managed to crack the heck out of his Nabi 2 digitizer screen. The LCD screen is fine and he can still use the Nabi, but I've noticed more and more cracks so I'm sure it's bound to break the LCD.
So, I went on eBay and ordered a piece of glass, but I'm not thinking it's not going to work. It was only like 13 bucks. I had a model number given to me after the fact (at070tn90), and I just looked and I didn't get that one. I'm just hoping it will work.
At any rate, I finally got the Nabi apart, but I've been fearful of removing the connectors for the screen. Can someone PLEASE tell me how to get the screen apart so I can try to replace it when I get the correct glass for it? PLEASE! There are NO Youtube vids for this...tons for the Nexus 7, but nada for Nabi.
Please help...I'm desperate! Thanks so much!!
The likelihood the digitizer isn't cracked is very low.
NABI2 touchscreen layering:
front glass..............thick (glue around outer most edges to frame)
airgap......................very thin (glue around edges)
digitizer glass........thin
lcd............................thick
I tried the same thing but the actual digitizer glass is like 1/10 the thickness of the front panel glass and glued to it on the edges. If the digitizer glass is not cracked, it will probably crack on attempted removal from the front panel. If the digitizer is fully working in-spite of the front glass cracking it may be possible to heat the front assembly up to the point the adhesive allows the glass to just fall out.... but as far as how close the glue melting point is to the melting point of the plastic frame is not something I know. The entire assembly is put together with some super strong double-sided sticky tape. If you can source just the digitizer and glass assembly I'd like to know.
Once one attempts a replacement and it doesn't work is it still possible to get Fuhu/Nabi to replace the screen (at reasonable cost)?
( If not you could just plug in a keyboard/mouse and use the hdmi out... would make a great XBMC server... once the port exists... )
.
Pictures?
oranrene7 said:
Okay, so my Terminator...errr, my son, managed to crack the heck out of his Nabi 2 digitizer screen. The LCD screen is fine and he can still use the Nabi, but I've noticed more and more cracks so I'm sure it's bound to break the LCD.
So, I went on eBay and ordered a piece of glass, but I'm not thinking it's not going to work. It was only like 13 bucks. I had a model number given to me after the fact (at070tn90), and I just looked and I didn't get that one. I'm just hoping it will work.
At any rate, I finally got the Nabi apart, but I've been fearful of removing the connectors for the screen. Can someone PLEASE tell me how to get the screen apart so I can try to replace it when I get the correct glass for it? PLEASE! There are NO Youtube vids for this...tons for the Nexus 7, but nada for Nabi.
Please help...I'm desperate! Thanks so much!!
Click to expand...
Click to collapse
Do you have any pictures of the digitizer and ribbon cable? Also location of the cable and size measurements.
manx_73 said:
Do you have any pictures of the digitizer and ribbon cable? Also location of the cable and size measurements.
Click to expand...
Click to collapse
I already put it back together because he was taking everyone's iPhones to play games on. lol The glass anatomizer (or whatever it's called), had a long thin strip and the LCD had a thicker one. Either way, the glass nowhere near fit. I had a feeling it was going to be too hard to replace anyway; hence the reason I can't seem to find a tutorial on fixing a Nabi.
And yes, Fuhu will fix it for like 85 bucks plus shipping...I only paid 90 for the tablet just recently (Craigslist). Oh well. I guess we'll just let him play till he cuts his finger.
Thank you both so much for your input. I appreciate it
Help replacing Nabi2 digitizer screen...
Any luck on this?
I have a Nabi 2 on which I've removed the broken digitizer. It was a bit more difficult than I had anticipated. I had to keep the heat gun on the glass and avoid heat-damage to the plastic. I used a small knife between the digitizer and the plastic frame. Next time, I may heat and bend a cheap knife into a Z shape to get under the glass without lifting it too much. I did get it out in some large pieces, but am not sure if I could do it intact if it hadn't been cracked.
Anyhow, the LCD looks great, but I can't seem to find the digitizer anywhere. The ribbon cable has a sticker with the following:
EP0700MLM1
12073*A1G.
272
View attachment 2625405
and on the back side above the chip, is:
40-90121-0
EDT REV.C
View attachment 2625413
on the inside glass is:
85701165
View attachment 2625417
The tiny text in the upper-right corner and written in mirror-image is:
XT2DA5A0118-EP0700 B1
I tried running the text through Google and aliexpress.com / alibaba.com, but to no avail. Anyone else have any luck?
Thanks,
Chip Stewart
ChipStewart said:
Any luck on this?
I have a Nabi 2 on which I've removed the broken digitizer. It was a bit more difficult than I had anticipated. I had to keep the heat gun on the glass and avoid heat-damage to the plastic. I used a small knife between the digitizer and the plastic frame. Next time, I may heat and bend a cheap knife into a Z shape to get under the glass without lifting it too much. I did get it out in some large pieces, but am not sure if I could do it intact if it hadn't been cracked.
Anyhow, the LCD looks great, but I can't seem to find the digitizer anywhere. The ribbon cable has a sticker with the following:
EP0700MLM1
12073*A1G.
272
View attachment 2625405
and on the back side above the chip, is:
40-90121-0
EDT REV.C
View attachment 2625413
on the inside glass is:
85701165
View attachment 2625417
The tiny text in the upper-right corner and written in mirror-image is:
XT2DA5A0118-EP0700 B1
I tried running the text through Google and aliexpress.com / alibaba.com, but to no avail. Anyone else have any luck?
Thanks,
Chip Stewart
Click to expand...
Click to collapse
I am also looking for the same digitizer model any luck? Anyone?
brianbri6 said:
I am also looking for the same digitizer model any luck? Anyone?
Click to expand...
Click to collapse
I am sorry for bringing back an old thread, but has anyone found a source for a proper replacement part for this? I am having a hell of a time finding a replacement part for the digitizer in my nabi2. It's as if nobody makes a replacement for the digitizers with EP0700MLM1 on the ribbon cable. About the only choice I have now is to find a used part, and pray that it also has the same kind of LCD screen within the housing.
--Rex
rex.torres said:
I am sorry for bringing back an old thread, but has anyone found a source for a proper replacement part for this? I am having a hell of a time finding a replacement part for the digitizer in my nabi2. It's as if nobody makes a replacement for the digitizers with EP0700MLM1 on the ribbon cable. About the only choice I have now is to find a used part, and pray that it also has the same kind of LCD screen within the housing.
--Rex
Click to expand...
Click to collapse
I am looking at a few on Fleabay now. You need to take yours apart and compare model numbers with the ones on Ebay. Just search ebay for Nabi 2 digitizer. about 20 results for it, ranging from $25 -65. The $65 one is a complete front panel minus the LCD. just unscrew the top panel and replace, it looks like.
Wow...I'm the original poster...and here I am years later still bothering with Nabi! lol In 2014, I went on Nabi's site and paid $60 to have the digitizer replaced. I never sent the Nabi in because a friend of mine gave me his kid's Nabi to use for parts (he couldn't get it to charge any longer). I took the entire front panel with LCD and digitizer and replaced it with mine. Worked like a charm...until my younger son stepped on it...on purpose! Lil turd! So, here I am again trying to fix the screen, BUT, this time I noted that I needed the LCD and the digitizer (the ribbon on the LCD was breaking off - not sure how that could have happened). At any rate, I ordered both the digitizer and LCD. I replaced them both and it's a no-go...not working. I still have it apart, but I have the cables plugged in, so when I move the screen around, the Nabi screen will come up, but the touchscreen isn't working. I may be sending the digitizer back, but I'm wondering if it's because of how they are lying on one another. Does anyone know if maybe the touchscreen doesn't work if it's too close or too far from the LCD screen. I don't mean by an obvious amount - I mean is there a "specific" amount of space. I am trying to get it in the casing exactly like it was before, but I don't want to do anything permanent until I know it's working 100%.
Also, you can easily and cheaply get the LCD and digitizer for the Nabi now - just stinks you have to order it from China and it takes forever to get here! I can only imagine how long a return/replacement is going to take. Ugh!
Oh, and Nabi has yet to return my $60 bucks...I have spent way too much on this tablet!
I ended up having to match my part number to a used but good part off of ebay. I had ordered several "new" digitizers and they never worked. There seemed to have been a design change somewhere along the line, or some missing information that made mine not work with the "new" parts available at the time.
However, to answer your question, the digitizer will work completely separated from the LCD as long as the ribbon cable is attached (of course). Rather than reassembling everything, I would only connect the digitizer to see if it worked. When I finally found one that worked, I then committed to doing the full repair.
It was a very painful process.
Is it an easy thing to take apart and put bk together if you have never done this before my daughter stood on her Nabi accident it was under her comfort blankie opps screen cracked but works fine she's only 2 ( well advanced for her age) soI dnt want her to use it incase she cuts her tiny fingers doesn't feel sharp but dnt want to risk it can't find any view on u tube still many years on be nice if someone would do one haha
Honestly...
It was a pain in the ass to remove the glass / digitizer from the nabi. If you're not careful--as I was--it is real easy to deform the plastic bezel that the glass / digitizer and LCD reside in. I ended up having to buy a replacement bezel that already had a digitizer and LCD attached to it. The LCD was DOA, but the one from my original was fine, so I begrudgingly transplanted that too.
Test the digitizer FIRST before committing to installing it on the plastic bezel.
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Oh yea.you have to be extra careful of that flex cable connecting to the lcd which is exposed
Sent from my SCH-I545 using xda app-developers app
warriorpluto said:
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
You can buy the lcd screen + digitizer which comes all pre-assembled and all you have to do it swap the whole screen + digitizer out as one unit..this way no fear of breaking anything..i see one on ebay for $158.00 US for the mega 6.3 i9200..but i think it will also work on the other 6.3 mega models..as they must all be the same that way...but i am not 100% sure on that. :good:
leetrevor81 said:
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
Click to expand...
Click to collapse
If you get the lcd and digitizer together, you can fix yourself and it's easy just as star master says. If you have a shop nearby they can replace just the glass
Sent from my SCH-I545 using xda app-developers app
leetrevor81 said:
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
Click to expand...
Click to collapse
And don't sell. $120 is a freaking rip off
Sent from my SCH-I545 using xda app-developers app
warriorpluto said:
And don't sell. $120 is a freaking rip off
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
How much do you think it would go for on ebay? (or somewhere else) I didn't think a damaged phone would be worth selling?
That phone is still with over $200 as is.just the good motherboard alone. Especially if it had a clean imei number..then counting other parts of the phone too
Sent from my SCH-I545 using xda app-developers app
Good tutorial how to fix it
There is some kind of double side transparent adhesive between LCD and digitizer. So good luck
Opened front glass
Hi, I opened front glass of Mega 5.8 to clean the dust inside it. When I put it back, the touch is not working. Earlier it was working perfectly, I did not remove any cables. Also that I cleaned it with dry cloth while the phone was on.
What may be the issue?
warriorpluto said:
Oh yea.you have to be extra careful of that flex cable connecting to the lcd which is exposed
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
How does it separate?
warriorpluto said:
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
Hi,
I've never worked on one of these before but I have repaired many GS3, GS4, Note 2 with no problems. You successfully repaired one so my question is, is the optical adhesive like the GS3 where it rubs off with your finger? I've noticed a difference in GS3 & GS4 adhesive the GS4 is more difficult to clean off digitizer.
That yellow flex cable in your pic looks like a Digitizer flex. The layers are LCD (bottom) / Digitizer (sits on top of LCD so center) / Glass (top which is what our finger touches).
I have a Mega coming in tomorrow and the customer bought just the glass online. I'll see if I can separate. If you have any questions let me know I have repaired many a phones.
Did you get it?
ReyesARG said:
Hi,
I've never worked on one of these before but I have repaired many GS3, GS4, Note 2 with no problems. You successfully repaired one so my question is, is the optical adhesive like the GS3 where it rubs off with your finger? I've noticed a difference in GS3 & GS4 adhesive the GS4 is more difficult to clean off digitizer.
That yellow flex cable in your pic looks like a Digitizer flex. The layers are LCD (bottom) / Digitizer (sits on top of LCD so center) / Glass (top which is what our finger touches).
I have a Mega coming in tomorrow and the customer bought just the glass online. I'll see if I can separate. If you have any questions let me know I have repaired many a phones.
Click to expand...
Click to collapse
I wonder how was it going with your repair?
http://www.witrigs.com/samsung-galaxy-mega-replacement-parts
Adhesive is a problem
letus1 said:
I wonder how was it going with your repair?
Click to expand...
Click to collapse
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
ReyesARG said:
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
Click to expand...
Click to collapse
If i separated the digitizer and the glass ftom the lcd, than can i bound the new one with LOCA or will that damage the LCD?
ReyesARG said:
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
Click to expand...
Click to collapse
I knew that was the only way to do it, with hot plate and fishing pole string. I'm sure it's a slow process. I'll have to invest in a good hot plate.
Sent from my SM-N900V using xda app-developers app
No huge investment needed, I use a standard electric pancake griddle which can be bought for around $20. Good, even heat. I've never tried the fishing line method but a pair of business cards does the job very well. I get it started with a dull razor blade in the corner and as soon as I see the glass separating, I slide a business card in behind it. Do the same for the other side. On these big screens, slide the cards down a bit, lay it down on heat, repeat. The trick to not busting the LCD is to keep the heat on it and take your time.
My temperature is set to 200 farenheit. Not sure off hand what that converts to in celsius. Ideally, you don't want the surface to pass 120 celsius. If in doubt, start low and increase temp slowly until the glue softens enough.
The glue we're taking about is LOCA[liquid optically clear adhesive] and is UV activated. It can be bought online pretty cheap. If you're going to replace the glass, go ahead and use the LOCA when putting the new glass on. I've seen sensitivity issues on glass that doesn't have the glue between it and the LCD. If you use the glue be sure to remove EVERYTHING from the frame including cameras, speakers, buttons and mics as it can get messy and go pretty much everywhere. To activate the glue you can literally take it outside on a sunny day and it will cure fairly quickly, about 5 mins or so. To remove it from unwanted areas just use a toothpick, toothbrush, and some rubbing alcohol. I've done it dozens of times this way and it always comes out looking factory fresh
VirtueToVice said:
No huge investment needed, I use a standard electric pancake griddle which can be bought for around $20. Good, even heat. I've never tried the fishing line method but a pair of business cards does the job very well. I get it started with a dull razor blade in the corner and as soon as I see the glass separating, I slide a business card in behind it. Do the same for the other side. On these big screens, slide the cards down a bit, lay it down on heat, repeat. The trick to not busting the LCD is to keep the heat on it and take your time.
My temperature is set to 200 farenheit. Not sure off hand what that converts to in celsius. Ideally, you don't want the surface to pass 120 celsius. If in doubt, start low and increase temp slowly until the glue softens enough.
The glue we're taking about is LOCA[liquid optically clear adhesive] and is UV activated. It can be bought online pretty cheap. If you're going to replace the glass, go ahead and use the LOCA when putting the new glass on. I've seen sensitivity issues on glass that doesn't have the glue between it and the LCD. If you use the glue be sure to remove EVERYTHING from the frame including cameras, speakers, buttons and mics as it can get messy and go pretty much everywhere. To activate the glue you can literally take it outside on a sunny day and it will cure fairly quickly, about 5 mins or so. To remove it from unwanted areas just use a toothpick, toothbrush, and some rubbing alcohol. I've done it dozens of times this way and it always comes out looking factory fresh
Click to expand...
Click to collapse
What kind of griddle? This is the one without the edges right?
Sent from my SM-N900V using xda app-developers app
starmaster10 said:
You can buy the lcd screen + digitizer which comes all pre-assembled and all you have to do it swap the whole screen + digitizer out as one unit..this way no fear of breaking anything..i see one on ebay for $158.00 US for the mega 6.3 i9200..but i think it will also work on the other 6.3 mega models..as they must all be the same that way...but i am not 100% sure on that. :good:
Click to expand...
Click to collapse
I like this..
fixxforyou said:
May i ask how much for this glass?
Click to expand...
Click to collapse
Who give your answer ? Mention it..