So I'm stuck... My USB is blinking on the other side of the y-cable we made, but my phone just says "Enter USB Host Mode.." I tried pressing Vol-dwn + Camera but it just stays there.. can anyone help?
mudher25 said:
So I'm stuck... My USB is blinking on the other side of the y-cable we made, but my phone just says "Enter USB Host Mode.." I tried pressing Vol-dwn + Camera but it just stays there.. can anyone help?
Click to expand...
Click to collapse
I have the same problem when I try to jailbrake my phone using RUU. So try Vol-dwn + Vol-up and it will work.
Tonyco1 said:
I have the same problem when I try to jailbrake my phone using RUU. So try Vol-dwn + Vol-up and it will work.
Click to expand...
Click to collapse
I held power and got out. My question is how do I jailbreak my phone? I tried going back into USB host mode but nothing happened. What should I do? I'm using a 1gb USB and also tried a 1GB SD card
Use microSD card (I used a 32mb)
If laptop -> remove all usb connected peripherals (ext WEbcam, mouse,printer etc)
Put the phone in USB HOST MODE
Make the connections at three ends of Y cables, male end connected to laptop. female to card reader and another to the phone.
Wait for the phone to display LOADING else, while phone still connected press power button
Phone restarts to usb host mode, wait for loading, when display wait further 10 mins
Display changes with Bootloader and radio installation
If fails or boots to bootloader screen, try running the gold card app again with the microSD card, make sure its formatted to FAT 32. Contains No any file except OMEGIMG.nbh
After initial one or two resets it definitely works!
P.S. check the connections by connecting the male end to laptop and other to phone to confirm charging! and likewise the female ends( in case you made the gig!)
mudher25 said:
I held power and got out. My question is how do I jailbreak my phone? I tried going back into USB host mode but nothing happened. What should I do? I'm using a 1gb USB and also tried a 1GB SD card
Click to expand...
Click to collapse
No going back to USB host mode this is mistake you should be in Bootloader mode turn off the phone than press Voldn + Volup and start the phone and still hold the buttons till get in Bootloader menu. After that it will work. Do you try first to use RUU ? Or you receive Country ID error ? Goldcard is only in case you receive country ID error. I use RUU without country ID error and it work very well.
Related
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
what are you trying to unlock, have you tried the master reset, whiles the phone is off, hold volume up/down then press the power and a menu should show up for master reset.
hi This problem can be solved only by the xtc clip
zozo -->> http://www.youtube.com/watch?v=QaYXxXgqDtU
Solution with Gold Card and Y Cabel.
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
Hi Brother,
Here is solution.
Windows Phone 7 handsets stuck in USB Host Mode
This looks like it's common to all WP7 phones, not just the Mozart but it's particularly annoying here because you need to feed the Sim Card/Flex adapter under the battery, over the battery retaining clip and under the battery cover. Very fiddly. Very easy to accidentally press the power button.
IF YOU PRESS THE POWER BUTTON INSTEAD OF VOL DOWN + CAMERA YOU WILL SOFT BRICK THE PHONE. IT WILL BE STUCK IN USB HOST MODE.
Fortunately to fix the phone you just need the "special cable" with MicroSD reader from the WP7 upgrade kit, the Gold Card you make in step A and the firmware for the phone you're working on.
1.Take the firmware .exe and extract the largest file (Ruu_signed.nbh or something similar)
2.Rename it using the same 4 letter naming convention that the DIAG file already on the goldcard with a IMG suffix e.g. MOZAIMG.nbh
3.Copy it to the MicroSD. You can use the XTC Clip as a card reader. This is the slowest part of the procedure.
4.Delete the DIAG file
5.Put the MicroSD card in the "special cable" and plug it into the phone without pressing any particular buttons. This will automatically reflash the phone with the possible bonus of debranding the phone.
6.Once the phone has booted up, you can proceed with trying to unlock it again.
Hope this helps.
Same problem encountered on the HD7: http://forums.phone-tools.cn/showthr...-mode-solution
Similar walkthrough for debranding: http://forum.xda-developers.com/showthread.php?t=892657
If its help you then thanks to orginal Master.
Thanks
Br, Raja
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
Dear Members...
After a long time i got solution for this problem. Yesterday i resolved one mozart which shows Enter USB Host Mode without using Y-Cable procedure.
This may work on many mozart, which has this problem with bootloader 5.12.2250 & dont have rom for their region. U can try this, before using Y-Cable procedure.
The solution is...
1. Download "WP7_Update_Cab_Sender.zip", from this forum & extract it.
2. Press Camera button & Power On the mozart. Dont release Camera button until the mozart shows computer connectivity symbol in the
display. Then release pressing the camera button & connect the moazrt to pc.
3. Now goto the extracted folder to this "WP7_Update_Cab_Sender\tools\x86" folder via MS-DOS prompt or copy cmd.exe to this folder and
open it. So that u will get, direct location of that path in command prompt.
4. In Command Prompt type "UpdateWP.exe /list". This shows the connected devices details in the screen.
5. Then type"UpdateWP.exe /reset". This will try to reset the mozart & restarts it to normal condition. Wait for few minutes
(not more than 5-10 mins) to get in to normal stage.
That's all...
If the solution doesn't work you, then dont blame me... & you can try with Y-Cable procedure...
It works dude thanks i shoud search for commands for ms dos
USB Host Mode
Was trying the same thing but no luck.
After several months, I realized my notebook's USB ports aren't that good anymore.
What I did is connect it to another PC (Win7 Home Premium) and download Zune (I installed other dependencies first like Windows Mobile Drivers for Vista). Get another cable if you have to. I connected it to the PC using a 3-headed USB cable (not a Y-cable since I don't have it).
Wait for several minutes, and the phone just shut itself off and on again with the HTC logo.
Instead of going to the USB mode, it goes to the....well, setup page after you factory reset it.
That's how I fixed my paperweight just today.
Must be Santa giving an early present.
+ Que PPC said:
It works dude thanks i shoud search for commands for ms dos
Click to expand...
Click to collapse
Sent from my SM-N900T using XDA Premium HD app
Hi everyone.
So I have a Motorola Droid RAZR XT910 its on 4.0.4 OTA with no root.
The issue I have is that I connect the phone to my PC via USB cable and it does not pick it up.
A few things you must know is:
•I have windows 7 32-bit and
•I am using the cable that comes with my phone
What happens when I plug my phone is the computer says installing drivers for unknown device and then it claims to have successfully installing them for "unknown device". My phone does give me option to chose what type of connection I want but it does charge.
Things I have tried:
•A different cable
•A different PC
• Re-installing drivers
• Re-installing Motocast
•Trying with USB Debugging enabled and disabled
•Different USB ports
•Factory reset
•Different USB ports
•Tried installing PIM Sync form Google Play Store
So yeah that's my problem any help will be helpful...
Try the drivers here:
http://www.motorola.com/consumers/v...59431210VgnVCM1000008406b00aRCRD&pubid=987654
When you try another cable, make sure that works with another device, and not just for charging.
The below instructions will help you troubleshoot if there is a problem with the usb connector on your phone.
1.Power off and disconnect usb cable.
2.Press and hold vol up and down, then hold the power button.
3.You should come to a boot mode selection menu.
4.Press vol down twice to highlight AP fastboot, press vol up once to select.
5.You should see AP fastboot flash mode (s), with last 2 lines saying "Connect USB, Data Cable"
6.Connect your USB cable to your PC and phone, and see if it says USB connected.
7. If nothing happens then it's probably a hardware problem, get it repaired.
Nikorasu said:
Try the drivers here:
http://www.motorola.com/consumers/v...59431210VgnVCM1000008406b00aRCRD&pubid=987654
When you try another cable, make sure that works with another device, and not just for charging.
The below instructions will help you troubleshoot if there is a problem with the usb connector on your phone.
1.Power off and disconnect usb cable.
2.Press and hold vol up and down, then hold the power button.
3.You should come to a boot mode selection menu.
4.Press vol down twice to highlight AP fastboot, press vol up once to select.
5.You should see AP fastboot flash mode (s), with last 2 lines saying "Connect USB, Data Cable"
6.Connect your USB cable to your PC and phone, and see if it says USB connected.
7. If nothing happens then it's probably a hardware problem, get it repaired.
Click to expand...
Click to collapse
Hi thank you for your help.
So I did this method on my PC and it was unsuccessful but i tried it on my mothers and it worked!
So I will update the drivers on my mothers PC and see If I can successfully connect to her PC and use USB mass storage for the first time since I've had Ice Cream Sandwich!
I will keep you updated
Its definitely software. Ill have to wait till there's a rooting application that doesn't require a connection between a PC and phone. One rooted I can flash a ROM from there on...
On your mother's PC, it worked in AP fastboot right? As in the words "USB connected" appears on your phone.
From there you can flash a rom.
Nikorasu said:
On your mother's PC, it worked in AP fastboot right? As in the words "USB connected" appears on your phone.
From there you can flash a rom.
Click to expand...
Click to collapse
I can flash fastboot files which I dont want to do.. I want to flash custom ROMs which require root.
The ap fastboot worked for me but when i restarted the phone it still wont connect with mass storage. i do not own a motorola usb cable mine is an LG and i dont really have money to buy one. bought the phone on ebay and it did not ship with one so ive been using this. it only connects as charging.
After a did a firmware update using USB Burning tool, without no troubles, I want to install other firmware because the accelerometer doesn't work, and so the auto-rotate function (it worked on the old firmware), and I can't get into recovery mode, the home + power function does not work anymore.
I want to use USB Burning tool to reflash the tablet, like the last time, but now I have this problem: when I connect the tablet trough USB cable with the power on, windows recognize the mass storage, but when the power is off, which I need for USB Burning tool, it doesn't do anything. It should show in the bottom-right corner that USB device found, but it doesn't.
I tried this:
1. to hold home-button and then to insert USB... nothing, it just shows the battery charging
2. to hold home+power button... nothing... doesn't enter in recovery mode, it's just loading android system.
3. SD card slot was empty when I tried this.
Does anybody had some king of problems? or know what's the problem?
Please, I need to fix this.
Hi all,
I am in desperate need of ya'llz help! Recently I followed the following instructions to the dot:
http://forum.xda-developers.com/showthread.php?t=2703774
in order to get root on 10.4.1.B.0.109. I ended up, like the author of the thread, in the so called bootloop. Tried everything and eventually managed to get out and restored to root 4.1.2. Thats where I am now.
The tablet works fine, however i am unable to connect to my pc with USB and also unable to charge via the charger. The tab is not detected in my computer, nor PC companion. Mass storage mode nor media mode work. I tried swapping cables, same.
The only thing I am able to get working through USB is charging when the tab is powered off, which means that the USB port is not broken.
I was thinking that updating would fix the problem, so I tried updating directly from the System update in the tab. It downloads 109, then restarts to install it, comes back with: "Could not install"!
Now my tab is not detected on my PC when its on, what to do ? How to update/Fix the USB problem!?
Any help is greatly appreciated!
Update
Ok I realized that the plugged cable only makes the red LED on the left light up, and when i click the power button, I see the battery picture in the display. Showing half charged. But the actual charge is not increasing.
Unplugging the USB, turns off the LED!
Help!
No ideas anyone? It charges from dead till medium. But no USB connection to the PC is possible! Cant update
centinel_x said:
No ideas anyone? It charges from dead till medium. But no USB connection to the PC is possible! Cant update
Click to expand...
Click to collapse
put your sd card in an adapter, put that in your pc and copy a zip with a full rom on it, put it back in your tablet and install the rom? Or try a different usb cable, maybe it's broken
centinel_x said:
No ideas anyone? It charges from dead till medium. But no USB connection to the PC is possible! Cant update
Click to expand...
Click to collapse
hold power + Vol+ to reset device and after that try to connect to pc to flash in flashtool.
Thanx
Hi guys,
thanks for the replies. Ive tried those already. Ive tried all different types of roms. The problem is that you need a restore image such as dual recovery on the tablet. Its rooted but there is not way to install a recovery image on it, without using a computer. And since it wont connect to the PC, no way..
:/
I've been booting LibreELEC/CoreELEC from SD card on my AZW (Beelink) W95 (S905W) box for years now. Yesterday I tried booting into the stock Android system (7.1 I think- I haven't done it for a while) but it wouldn't boot. Not being one to leave well enough alone I decided to try a reset using a toothpick in the reset hole by the power plug. It flashed the start screen for a split second and then stopped. After that it wouldn't boot off the CoreELEC SD card either.
I've tried a clean CoreELEC install, stock firmware, Amlogic Burn Card Maker, and TWRP on the SD card - none of them get me past a black screen.
I don't think the reset button is doing anything (I depress it while plugging in the power jack). In fact, I don't know if it ever worked. My box had previously always booted off a SD card if it was inserted in the slot without having to do anything special.
My box isn't completely dead but comatose. The signs of life are:
1) The blue LED comes on when I plug in the power cord.
2) After about 20 minutes or so the blue LED will go off. If I press the power button on the remote it comes back on.
3) My router sees it on my network as active. But I get connection refused when I try access it using Windows File Explorer or try to SSH into it using Putty.
4) When I insert a SD card into the slot it writes Andriod and LOST.DIR folders to it.
I haven't tried the Amlogic USB Burning Tool yet because I don't have an USB 2.0 Type A male to male cable - but I've ordered one. My concern is I won't be able to put it in reset mode since I'm not sure the reset button does anything (but I can feel it click).
Is there anything else I should try while I'm waiting for my cable to arrive?
Any recommendations on how I should proceed once my cable arrives?
Thanks
RKCRLR said:
I've been booting LibreELEC/CoreELEC from SD card on my AZW (Beelink) W95 (S905W) box for years now. Yesterday I tried booting into the stock Android system (7.1 I think- I haven't done it for a while) but it wouldn't boot. Not being one to leave well enough alone I decided to try a reset using a toothpick in the reset hole by the power plug. It flashed the start screen for a split second and then stopped. After that it wouldn't boot off the CoreELEC SD card either.
I've tried a clean CoreELEC install, stock firmware, Amlogic Burn Card Maker, and TWRP on the SD card - none of them get me past a black screen.
I don't think the reset button is doing anything (I depress it while plugging in the power jack). In fact, I don't know if it ever worked. My box had previously always booted off a SD card if it was inserted in the slot without having to do anything special.
My box isn't completely dead but comatose. The signs of life are:
1) The blue LED comes on when I plug in the power cord.
2) After about 20 minutes or so the blue LED will go off. If I press the power button on the remote it comes back on.
3) My router sees it on my network as active. But I get connection refused when I try access it using Windows File Explorer or try to SSH into it using Putty.
4) When I insert a SD card into the slot it writes Andriod and LOST.DIR folders to it.
I haven't tried the Amlogic USB Burning Tool yet because I don't have an USB 2.0 Type A male to male cable - but I've ordered one. My concern is I won't be able to put it in reset mode since I'm not sure the reset button does anything (but I can feel it click).
Is there anything else I should try while I'm waiting for my cable to arrive?
Any recommendations on how I should proceed once my cable arrives?
Thanks
Click to expand...
Click to collapse
Hi, your device seems to be in a strange state currently, only thing i can reccomend is trying a few firmwares to see what works for you, you should be able to flash most s905w based roms, if your device cant be detected by USB burn tool you might need to use ask Rom Mode" to force your box to be detected by burn tool, this makes it almost impossible to brick a box
Thanks for the suggestions, I'm a complete newbie at this.
Is the Ask ROM Mode an option in USB Burning Tool?
I have an OEM W95 firmware update file (in both .img and and an OTA in .zip format) but they may be older than what is currently on the box. I also found a TWRP file for the S905W. But I don't know how to use any of these.
I downloaded the AMLogic Tools 6.0.0 and tried the AMLogic Flash Tool since it seems to work through the Ethernet port. I assumed this because you access the box via an IP address but I really don't know. I watched the video but couldn't find any detailed instructions on how to use it.
When I pressed the Connect button it said it connected and I had the green Connected display (I was connecting through my LAN - I don't know if I should connect directly with an ethernet cable). I loaded my .img file and said Flash. It says it is flashing and a second or so later it says SUCCESS! However the box still doesn't boot. I tried both Boot and Recovery (I don't know which option I should choose). I think that the SUCCESS! message is incorrect since I get the message even if I press the Flash button without the box connected. However, I can't connect to the box without the ethernet cable connected so the connected message seems correct.
Am I using the AMLogic Flash Tool correctly?
I was thinking about trying the S905W atvExperience ROM but thought I'd wait until I got my USB cable before before doing something more drastic.
Any other suggestions?
Thanks
OK, so my male to male USB cable arrived and I managed to get my box un-bricked using AMLogic USB Burning tool with a factory .img file. It took several tries. I kept getting errors when it tried to erase the bootloader or would get to 7%, progress would stop for about a minute, and then Burning Tool would close.
I finally got it to proceed all the way by holding in the reset button, plugging in the USB cable (no power cable), and keeping the reset button pushed the whole time (I don't know if this was just a coincidence). Also, I hadn't closed Burning Tool after the previous error erasing the bootloader. I'm posting all this in case someone else has a similar problem.
After that, it still wouldn't boot of the CoreELEC SD card with the reset button pushed down. It would go straight into the Android OS. I got it to boot into CoreELEC by installing the Reboot to LibreELEC app. Now it always restarts in CoreELEC the way it used to when the SD card is left in. I think this is how I got LibreELEC working years ago.
So, now I'm contemplating installing atvXperience but I have a couple of questions:
What would be the best way to install atvXperience without being able to the reset button to put the box into recovery mode?
What would be the best way to prepare for not being able to use the reset button to put the box into recovery mode if something were to go wrong during flashing?
Thanks for any help.
OK, so my male to male USB cable arrived and I managed to get my box un-bricked using AMLogic USB Burning tool with a factory .img file. It took several tries. I kept getting errors when it tried to erase the bootloader or would get to 7%, progress would stop for about a minute, and then Burning Tool would close.
I finally got it to proceed all the way by holding in the reset button, plugging in the USB cable (no power cable), and keeping the reset button pushed the whole time (I don't know if this was just a coincidence). Also, I hadn't closed Burning Tool after the previous error erasing the bootloader. I'm posting all this in case someone else has a similar problem.
After that, it still wouldn't boot of the CoreELEC SD card with the reset button pushed down. It would go straight into the Android OS. I got it to boot into CoreELEC by installing the Reboot to LibreELEC app. Now it always restarts in CoreELEC the way it used to when the SD card is left in. I think this is how I got LibreELEC working years ago.
So, now I'm contemplating installing atvXperience but I have a couple of questions:
What would be the best way to install atvXperience without being able to the reset button to put the box into recovery mode? (I did try flashing atvXperience once using USB Burning Tool but I got the same error erasing bootloader)
What would be the best way to prepare for not being able to use the reset button to put the box into recovery mode if something were to go wrong during flashing?
Thanks for any help.
Another follow up post for anyone with the same problem. I did some searching and found out I'm not the only one with a box that the reset button doesn't work. A work around for them was to connect the male to male USB cable, load the image into Burning Tool, press Start, and then plug in the power supply. The image file would then start flashing.
However, my box would start booting as soon as I connected the USB cable (didn't need the power supply). So I loaded the image into Burning Tool, pressed Start, and then connected the USB cable. This appears to be the work around for my box (I probably did this when I got my box to recover the first time - holding the reset button was probably irrelevant).
This procedure works for the stock firmware but when I try to flash the atvXperience image file the box hangs at 7%. So I still need some help there.
Also, is there a ATV ROM better suited for my S905W box (2/16 GB)?
W95 is really ****ing box whenever you feel you get off from the current problem will be into next one.
I have installed atvx Rom but afterthat when I tried adian rom my device bricked.
Without Ubt flashing it's connect but as I start flash it's sound unknown device and give flash error