Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
what are you trying to unlock, have you tried the master reset, whiles the phone is off, hold volume up/down then press the power and a menu should show up for master reset.
hi This problem can be solved only by the xtc clip
zozo -->> http://www.youtube.com/watch?v=QaYXxXgqDtU
Solution with Gold Card and Y Cabel.
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
Hi Brother,
Here is solution.
Windows Phone 7 handsets stuck in USB Host Mode
This looks like it's common to all WP7 phones, not just the Mozart but it's particularly annoying here because you need to feed the Sim Card/Flex adapter under the battery, over the battery retaining clip and under the battery cover. Very fiddly. Very easy to accidentally press the power button.
IF YOU PRESS THE POWER BUTTON INSTEAD OF VOL DOWN + CAMERA YOU WILL SOFT BRICK THE PHONE. IT WILL BE STUCK IN USB HOST MODE.
Fortunately to fix the phone you just need the "special cable" with MicroSD reader from the WP7 upgrade kit, the Gold Card you make in step A and the firmware for the phone you're working on.
1.Take the firmware .exe and extract the largest file (Ruu_signed.nbh or something similar)
2.Rename it using the same 4 letter naming convention that the DIAG file already on the goldcard with a IMG suffix e.g. MOZAIMG.nbh
3.Copy it to the MicroSD. You can use the XTC Clip as a card reader. This is the slowest part of the procedure.
4.Delete the DIAG file
5.Put the MicroSD card in the "special cable" and plug it into the phone without pressing any particular buttons. This will automatically reflash the phone with the possible bonus of debranding the phone.
6.Once the phone has booted up, you can proceed with trying to unlock it again.
Hope this helps.
Same problem encountered on the HD7: http://forums.phone-tools.cn/showthr...-mode-solution
Similar walkthrough for debranding: http://forum.xda-developers.com/showthread.php?t=892657
If its help you then thanks to orginal Master.
Thanks
Br, Raja
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
Dear Members...
After a long time i got solution for this problem. Yesterday i resolved one mozart which shows Enter USB Host Mode without using Y-Cable procedure.
This may work on many mozart, which has this problem with bootloader 5.12.2250 & dont have rom for their region. U can try this, before using Y-Cable procedure.
The solution is...
1. Download "WP7_Update_Cab_Sender.zip", from this forum & extract it.
2. Press Camera button & Power On the mozart. Dont release Camera button until the mozart shows computer connectivity symbol in the
display. Then release pressing the camera button & connect the moazrt to pc.
3. Now goto the extracted folder to this "WP7_Update_Cab_Sender\tools\x86" folder via MS-DOS prompt or copy cmd.exe to this folder and
open it. So that u will get, direct location of that path in command prompt.
4. In Command Prompt type "UpdateWP.exe /list". This shows the connected devices details in the screen.
5. Then type"UpdateWP.exe /reset". This will try to reset the mozart & restarts it to normal condition. Wait for few minutes
(not more than 5-10 mins) to get in to normal stage.
That's all...
If the solution doesn't work you, then dont blame me... & you can try with Y-Cable procedure...
It works dude thanks i shoud search for commands for ms dos
USB Host Mode
Was trying the same thing but no luck.
After several months, I realized my notebook's USB ports aren't that good anymore.
What I did is connect it to another PC (Win7 Home Premium) and download Zune (I installed other dependencies first like Windows Mobile Drivers for Vista). Get another cable if you have to. I connected it to the PC using a 3-headed USB cable (not a Y-cable since I don't have it).
Wait for several minutes, and the phone just shut itself off and on again with the HTC logo.
Instead of going to the USB mode, it goes to the....well, setup page after you factory reset it.
That's how I fixed my paperweight just today.
Must be Santa giving an early present.
+ Que PPC said:
It works dude thanks i shoud search for commands for ms dos
Click to expand...
Click to collapse
Sent from my SM-N900T using XDA Premium HD app
Related
Well I was trying to upgrade mt niki to 6.1 but apparently I must have missed a step or did something I shouldt have and now I am stuck with the color bar screen. Can anything be done? I am running Vista.
tri-colour = Bootloader
The tri colour screen is the boot loader screen, when you updated, did the progress bar go allll the way to 100%?
If so, its in bootloader, try to flash another rom from you computer,
Also run through what you done to update - What rom also. Did you hard-spl, Uspl or anything like that?
It stopped at 15%. These are the directions I was following:
Originally Posted by Judge584
Follow these steps:
1. download the attached files (flash-uspl-niki.zip & sspl-1.16-nike)
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the uspl by running ROMUpdateUtility.exe from flash-uspl-niki
9. Now you can flash the latest rom update to have spl 1.22 and wm6.1.
ouch, Thats the only problem with sspl,
urmm.
How long did it stay at 15%?
As the device isn't CID unlocked you can only flash official roms...
Find an official rom, in the bootloader connect the USB and see if it will flash. It should do!
fingers crossed..
the only rom I can find for singtel in singapore is an updated one so I am trying that now so far so good, I am at 30%. So if this will get me going again can you offer a little advice or explination as to your last post, how do I go about loading a newer 6.1 rom on my device?
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Deejaynate said:
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Click to expand...
Click to collapse
well i was able to fix it by using the singtel rom. I want to use the Niki SuperCID unlocker but I have to install the " HardSPL 1.15 MFG " first - can you walk mw through this so I dont brick my touch again. do you have messenger?
yeah Windows live messenger, add me [email protected]
sorry to hijack your thread, but I encountered exactly the same thing. The screen is now stuck with 3 colour bands. I tried to flash it with an official rom, but the computer is not connecting with the phone, active sync does not recognise the device, any help!?
this is what I did:
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. running ROMUpdateUtility.exe from flash-uspl-niki
Sorry for the non prompt reply
I have been at work alot lately,
sorry for a non prompt reply.
Active sync wont connect to your phone, as its in bootloader mode.
At the tri-colour screen, does you computer beep when you connect it, or try to install drivers?
thanks for replying!
no beep from the computer, when connecting the usb to the phone, the phone changes from "serial" to "usb".
I tried reflashing with ROMUpdateUtility.exe from flash-uspl-niki, it will work, but says fail and will go into recovery mode. It will then complete the "recovery" action and go back to flashing new rom which won't work.......
The same ocurred with me!! Help me!
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
luismatos123 said:
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
Click to expand...
Click to collapse
You need to flash an original ROM from your service provider (phone company).
Hi,
My new Gene is bricked. I am trying with the Orefkov SPL updater. I am getting the Boot loader screen but I am stuck with MTTY. I am not getting the USB button. Please help
WHAT IS YOUR OS? IS IT WINDOWS XP OR VISTA/7?
IF YOU ARE USING WINDOWS VISTA/7 YOU NEED TO HAVE WINDOWS XP ACTIVESYNC DRIVER INSTALLED.
Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Here is the link to the Master of all masters Sumit's official thread for more info:
http://forum.xda-developers.com/showthread.php?t=472169
HI Schizo,
Thanks for the quick reply.
I have Win XP and I have ActiveSync installed. I have removed SD Card, Sim and did the same way you have explained. But still I am getting only COM1 and COM2 in the dropdown in MTTY.
Please help.
Anything specific to be done with ActiveSync?
go to computer> right click and select properties and go to device manager. Is there anything called pocketpc usb sync? If there is pocketpc usbsync or unknown device then Update it with the driver i have attached below. and one more thing keep on refreshing the page from time to time.
No Schizo. I dont have anything like that.
I have Windows Mobile-based Device#7 in Network Adapters. Is that a problem?
rexhyd said:
No Schizo. I dont have anything like that.
I have Windows Mobile-based Device#7 in Network Adapters. Is that a problem?
Click to expand...
Click to collapse
then upgrade that with pocktpc usb sync driver i have attached above and try again. Let me know if that worked.
Link:
http://forum.xda-developers.com/attachment.php?attachmentid=270636&d=1264088925
Sorry to ask but how to update it?
rexhyd said:
Sorry to ask but how to update it?
Click to expand...
Click to collapse
Unzip the files i have send you.
Go to device manager, right click on windows mobile and select update driver.
select browse my computer for driver.
select let me pick from device drivers and choose have disk.
go to the folder you have extracted the drivers and select pocketpc usb sync.
I am using windows seven but i believe steps is basically the same
I have right clicked on WceRndis and wceusbsh and selected Install. Will that do?
rexhyd said:
Sorry to ask but how to update it?
Click to expand...
Click to collapse
unzip that and then right click on inf files it shows install
then re plug device
rexhyd said:
I have right clicked on WceRndis and wceusbsh and selected Install. Will that do?
Click to expand...
Click to collapse
Now replug the device and start all the steps as posted before. Let me know if that works
Hi,
I have done it. Now I have a white screen and I am going to run RomUpdateUtility.exe program.
Thanks a lot
I am done now My SPL is 1.07.Oref. Thanks a lot guys. I was damn scared that I've lost my Gene. But You guys made it. Thanks once again.
Can you suggest which ROM will be best for my mobile?Please
congratulations, now update to the ROM of your choice. Glad to help. Had the same problem, woke up till 5 am in the morning trying to fix that. For new ROMS just browse the section. Plenty of ROMs for our new gene here. Enjoy
@schizo440 Good job mate
Great to hear that one more Gene was saved. Good job schizo440
@rexhyd : From now on, never flash any ROM that says its for Old Gene, and also those which say Stock Rom or Official ROM etc. For the second type of roms, ask in the forum first, whether they are safe or not. Good luck!
I have the same problem too.
Hey, I have the same problem. Im stuck at the tricolour screen showing SPL 1.10. Olip. Mtty doesn't sho usb option. Im on Windows 7 please help.
msrkanurag said:
Hey, I have the same problem. Im stuck at the tricolour screen showing SPL 1.10. Olip. Mtty doesn't sho usb option. Im on Windows 7 please help.
Click to expand...
Click to collapse
kill active sync process at taskmanager
really nice work schizo440......
Hi all
I have a problem with my hero not being recognized by my PC. This happened after a weekend trip and i charged the phone with iphone USB adapter as i lost my one and now after returning from my trip i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message.
Also my Amon_Ra recovery i used has been wiped and i cant get into recovery or install any rom at all.
I am thinking this might be the same USB brick that affected some Desire owners but i am not sure.
So please if anyone can help me, please do.
Thanks in advance.
fizzle101 said:
Hi all
I have a problem with my hero not being recognized by my PC. This happened after a weekend trip and i charged the phone with iphone USB adapter as i lost my one and now after returning from my trip i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message.
Also my Amon_Ra recovery i used has been wiped and i cant get into recovery or install any rom at all.
I am thinking this might be the same USB brick that affected some Desire owners but i am not sure.
So please if anyone can help me, please do.
Thanks in advance.
Click to expand...
Click to collapse
this happen to me. What i did was switch my phone off, plug in the usb and switched it back on. then wait for windows to say it not recognised. then go to to device and printers and uninstall the drivers for the phone. Disconnect and reconnect the usb back to the phone and it it will pick it up.
Can you try booting in fastboot and tell me if that is recognized?
it still doesnt recognize it in fastboot
fc_Kuro said:
this happen to me. What i did was switch my phone off, plug in the usb and switched it back on. then wait for windows to say it not recognised. then go to to device and printers and uninstall the drivers for the phone. Disconnect and reconnect the usb back to the phone and it it will pick it up.
Click to expand...
Click to collapse
i have tried that and it doesnt help
fizzle101 said:
i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message
Click to expand...
Click to collapse
Sounds like its just a driver issue. Have you tried plugging it in, when you get that message open DEVICE MANAGER,... Find the yellow "!", right click it, uninstall, unplug phone, reboot PC.
.... Then use BTDAG's [Guide] How to Setup Correct Hero Drivers (for x86 & x64 users)
I hav the same problem. In recover mode it works but then turn on the phone, there is no popup options as before. Tried around with drivers but didnt work either. But found a solution which is very convenient. I dont know if it works on other ROM versions but I'm on 2.1 (Villain10).
- Install extended control widget (dont remember where I got it but you can google, it seems I cannot find it on the market)
- Add this widget to the home screen: Menu/Add to Home/Widget/ Extended Control bar (you can choose the size from 1x1 to 1x4) then select "Mass storage" at the bottom, apply.
Now you have a widget to turn on/off USB storage. When you connect Hero to the PC, just click on this widget then the PC will connect to the SD card, and click one more to turn it off.
ok i will give that a try
crk23 said:
I hav the same problem. In recover mode it works but then turn on the phone, there is no popup options as before. Tried around with drivers but didnt work either. But found a solution which is very convenient. I dont know if it works on other ROM versions but I'm on 2.1 (Villain10).
- Install extended control widget (dont remember where I got it but you can google, it seems I cannot find it on the market)
- Add this widget to the home screen: Menu/Add to Home/Widget/ Extended Control bar (you can choose the size from 1x1 to 1x4) then select "Mass storage" at the bottom, apply.
Now you have a widget to turn on/off USB storage. When you connect Hero to the PC, just click on this widget then the PC will connect to the SD card, and click one more to turn it off.
Click to expand...
Click to collapse
that didnt work. o well i guess i am stock with the rom i have there.
fizzle101 said:
that didnt work. o well i guess i am stock with the rom i have there.
Click to expand...
Click to collapse
i've got this problem once and it was as simple as the cable was damaged...
i changed the cable and since then, everything works try that.
robocik said:
i've got this problem once and it was as simple as the cable was damaged...
i changed the cable and since then, everything works try that.
Click to expand...
Click to collapse
i have tried everything. changed the cable, used different pc but nothing works. i think is a hardware problem, something might be broken inside or something like that
Did you ever got this solved? I have the same problem only i use stock rom 2.1 Hero.. driving me nuts ...
baklap said:
Did you ever got this solved? I have the same problem only i use stock rom 2.1 Hero.. driving me nuts ...
Click to expand...
Click to collapse
No i havent and i gave up trying because i dnt think there is a fix for it. if yours is unrooted and the warranty is still valid you should consider returning it to HTC maybe they might replace it
got the same problem. Any solution so far ??
ddotpatel said:
Sounds like its just a driver issue. Have you tried plugging it in, when you get that message open DEVICE MANAGER,... Find the yellow "!", right click it, uninstall, unplug phone, reboot PC.
.... Then use BTDAG's [Guide] How to Setup Correct Hero Drivers (for x86 & x64 users)
Click to expand...
Click to collapse
Did you try that?..... You need to do the reboot PC/Laptop after uninstalling ALL HTC drivers! Then when you reboot PC, plug phone back in, should say "not recognised" again,... then follow BTDAG's guide. T'is definitely a driver issue!
tried flashing 3 roms, modaco, radug and now kimera... none working.
can connect in fastboot, it shows up in device manager as android 1.0
ive tried 3 different usb cables and 4 differet pcs, still there is no response on my phone !!!
using villian rom 10.0 rite now.
okay it boots up into fastboot and fastboot usb shows up on the screen in red,
BUT when i use the "adb devices" command in adb it doesnt show the device,
it is showing as android 1.0 in devices and printers (windows 7)
You need to use....
fastboot devices
....when your are in fastboot.
What happens when you go into your recovery, select "Toggle MS/USB" with USB connected to PC?
okay
fastboot devices command shows some serial number.
then i tried adb remount, it gave an error....
enabling usb-ms with cable attached gives no response
ok i think it might be USB driver like ddotpatel said but i am not sure.
i reinstalled my whole windows 7 to 32bit now instead of the 64bit version i was using before and today i just connected my hero to my PC and windows 7 did its thing and installed the drivers and finally my hero can mount the SD card in my PC again although i kept getting this can perform faster in USB 2.0 port or something like that i didn’t care as long as i can mount my SD card again.
now went into fastboot and used the fastboot device command and i could see my hero serial no. but when i try to flash the amonra recovery i got the permission error (i cant really remember). i tried flashing using the adb method but still no luck.
so i went to market and downloaded rom manager and used it to flash clockwork recovery and now i could boot to clockwork recovery.
from this recovery i can now flash any rom i want and although there are still a few more problems i am glad now that i can flash custom roms again.
the problem i can see so far but i can deal with is
1. i don’t think fastboot commands work even if the phone is detected.
2. SD card mounts at USB 1.1 speed. (i have tried different ports and cable but still the same thing and this is the ports i use for my N1, Desire and my other android phones with USB 2.0 speed)
PS: adb commands for pushing and removing apps is working.
Hope this can be helpful to those experiencing the same problem.
Instead of re-installing your entire OS just use usbdeview to remove the failing drivers.
Also remove any old HTC Sync installs and install the latest version.
Hey guys, as the title suggests....im having trouble
Trying to update my ROM.
Active sync works fine, up to the point I have to run the RUU and .nbh files, it just drops out and then i get the error 266 coming up.....asking me to check the cable etc.
Tried different USB ports and leads with no joy.
Strange one this, as I have updated my ROM before (around a year ago) with no trouble.
Help very much appreciated.
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
AndrewSh said:
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
Click to expand...
Click to collapse
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first?
Im following these instructions:
FIRST TIME FLASH
1. Remove SD (and remove Application Data and Program Files folders from it using SD card reader)
2. Remove HSPL with HSPL2_RUN.exe (flash SPL 1.66.0000 with HSPL2_RUN.exe)
3. PowerOff the phone
4. Boot to bootloader (VolDown+PowerOn) and when it shows "USB" flash stock ROM by running matching RUU_Leo_S_HTC_XXX_3.14.XXX_Radio_15.42.50.11U_2.15 .50.14_LEO_S_Ship.exe (get yours HERE or for Orange UK/FR HERE)
5. Hard Reset (when phone starts booting after step 4, remove the battery, insert it back press VolUp+VolDown and still holding both press PowerOn and follow the instructions)
6. Boot to homescreen.
7. Run SSPL_RUU.exe with Artemis v4X RUU_Signed_XXXX.nbh in the same folder - YOU HAVE TO BE ON HOME SCREEN, NOT BOOTLOADER (this took me 3 tries until succeded - yes - nerve wrecking, but works). If it doesn't work (hangs on black screen for more than 2min or stays at 0%) remove the battery and try again. If still doesn't work - try solutions in NOTE below.
8. Hard reset (instructions in step 5)
9. when on homescreen - softreset.
10. Insert SD
marlon32 said:
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first
Click to expand...
Click to collapse
You're going about things in a strange manner, using hspl.exe to set a stock spl and then using sspl to flash the rom? Pretty non standard, what are you aiming for? My guess is you are using outdated instructions from before Hspl4 was released to handle spl/hspl 3.03 (just a guess, of course)
Stabdard flashing a 3.14 rom would go as follows,
Phone into bootloader(forget actuvesync)
Run Hspl4.exe, choose 3.03.hspl
Back into bootloader,
Run the Artemis flash using custom ruu .
Done.
It won't show the current installed image because that is a simple registry entry and is only accessible when winmo is running, but when winmo is running the USB times out when the ruu reboots into bootloader,sim that's why we manually enter bootloader.
(I haven't checked in the Artemis thread as to if there's a reason why his rom wouldn't follow standard proceedures, but I did use exactly your process prior to Hspl4 release)
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
marlon32 said:
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
Click to expand...
Click to collapse
Thanks M8 Had the same problem and moved my usb cable to another port worked 100%
So I'm stuck... My USB is blinking on the other side of the y-cable we made, but my phone just says "Enter USB Host Mode.." I tried pressing Vol-dwn + Camera but it just stays there.. can anyone help?
mudher25 said:
So I'm stuck... My USB is blinking on the other side of the y-cable we made, but my phone just says "Enter USB Host Mode.." I tried pressing Vol-dwn + Camera but it just stays there.. can anyone help?
Click to expand...
Click to collapse
I have the same problem when I try to jailbrake my phone using RUU. So try Vol-dwn + Vol-up and it will work.
Tonyco1 said:
I have the same problem when I try to jailbrake my phone using RUU. So try Vol-dwn + Vol-up and it will work.
Click to expand...
Click to collapse
I held power and got out. My question is how do I jailbreak my phone? I tried going back into USB host mode but nothing happened. What should I do? I'm using a 1gb USB and also tried a 1GB SD card
Use microSD card (I used a 32mb)
If laptop -> remove all usb connected peripherals (ext WEbcam, mouse,printer etc)
Put the phone in USB HOST MODE
Make the connections at three ends of Y cables, male end connected to laptop. female to card reader and another to the phone.
Wait for the phone to display LOADING else, while phone still connected press power button
Phone restarts to usb host mode, wait for loading, when display wait further 10 mins
Display changes with Bootloader and radio installation
If fails or boots to bootloader screen, try running the gold card app again with the microSD card, make sure its formatted to FAT 32. Contains No any file except OMEGIMG.nbh
After initial one or two resets it definitely works!
P.S. check the connections by connecting the male end to laptop and other to phone to confirm charging! and likewise the female ends( in case you made the gig!)
mudher25 said:
I held power and got out. My question is how do I jailbreak my phone? I tried going back into USB host mode but nothing happened. What should I do? I'm using a 1gb USB and also tried a 1GB SD card
Click to expand...
Click to collapse
No going back to USB host mode this is mistake you should be in Bootloader mode turn off the phone than press Voldn + Volup and start the phone and still hold the buttons till get in Bootloader menu. After that it will work. Do you try first to use RUU ? Or you receive Country ID error ? Goldcard is only in case you receive country ID error. I use RUU without country ID error and it work very well.