Hi all
I have a problem with my hero not being recognized by my PC. This happened after a weekend trip and i charged the phone with iphone USB adapter as i lost my one and now after returning from my trip i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message.
Also my Amon_Ra recovery i used has been wiped and i cant get into recovery or install any rom at all.
I am thinking this might be the same USB brick that affected some Desire owners but i am not sure.
So please if anyone can help me, please do.
Thanks in advance.
fizzle101 said:
Hi all
I have a problem with my hero not being recognized by my PC. This happened after a weekend trip and i charged the phone with iphone USB adapter as i lost my one and now after returning from my trip i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message.
Also my Amon_Ra recovery i used has been wiped and i cant get into recovery or install any rom at all.
I am thinking this might be the same USB brick that affected some Desire owners but i am not sure.
So please if anyone can help me, please do.
Thanks in advance.
Click to expand...
Click to collapse
this happen to me. What i did was switch my phone off, plug in the usb and switched it back on. then wait for windows to say it not recognised. then go to to device and printers and uninstall the drivers for the phone. Disconnect and reconnect the usb back to the phone and it it will pick it up.
Can you try booting in fastboot and tell me if that is recognized?
it still doesnt recognize it in fastboot
fc_Kuro said:
this happen to me. What i did was switch my phone off, plug in the usb and switched it back on. then wait for windows to say it not recognised. then go to to device and printers and uninstall the drivers for the phone. Disconnect and reconnect the usb back to the phone and it it will pick it up.
Click to expand...
Click to collapse
i have tried that and it doesnt help
fizzle101 said:
i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message
Click to expand...
Click to collapse
Sounds like its just a driver issue. Have you tried plugging it in, when you get that message open DEVICE MANAGER,... Find the yellow "!", right click it, uninstall, unplug phone, reboot PC.
.... Then use BTDAG's [Guide] How to Setup Correct Hero Drivers (for x86 & x64 users)
I hav the same problem. In recover mode it works but then turn on the phone, there is no popup options as before. Tried around with drivers but didnt work either. But found a solution which is very convenient. I dont know if it works on other ROM versions but I'm on 2.1 (Villain10).
- Install extended control widget (dont remember where I got it but you can google, it seems I cannot find it on the market)
- Add this widget to the home screen: Menu/Add to Home/Widget/ Extended Control bar (you can choose the size from 1x1 to 1x4) then select "Mass storage" at the bottom, apply.
Now you have a widget to turn on/off USB storage. When you connect Hero to the PC, just click on this widget then the PC will connect to the SD card, and click one more to turn it off.
ok i will give that a try
crk23 said:
I hav the same problem. In recover mode it works but then turn on the phone, there is no popup options as before. Tried around with drivers but didnt work either. But found a solution which is very convenient. I dont know if it works on other ROM versions but I'm on 2.1 (Villain10).
- Install extended control widget (dont remember where I got it but you can google, it seems I cannot find it on the market)
- Add this widget to the home screen: Menu/Add to Home/Widget/ Extended Control bar (you can choose the size from 1x1 to 1x4) then select "Mass storage" at the bottom, apply.
Now you have a widget to turn on/off USB storage. When you connect Hero to the PC, just click on this widget then the PC will connect to the SD card, and click one more to turn it off.
Click to expand...
Click to collapse
that didnt work. o well i guess i am stock with the rom i have there.
fizzle101 said:
that didnt work. o well i guess i am stock with the rom i have there.
Click to expand...
Click to collapse
i've got this problem once and it was as simple as the cable was damaged...
i changed the cable and since then, everything works try that.
robocik said:
i've got this problem once and it was as simple as the cable was damaged...
i changed the cable and since then, everything works try that.
Click to expand...
Click to collapse
i have tried everything. changed the cable, used different pc but nothing works. i think is a hardware problem, something might be broken inside or something like that
Did you ever got this solved? I have the same problem only i use stock rom 2.1 Hero.. driving me nuts ...
baklap said:
Did you ever got this solved? I have the same problem only i use stock rom 2.1 Hero.. driving me nuts ...
Click to expand...
Click to collapse
No i havent and i gave up trying because i dnt think there is a fix for it. if yours is unrooted and the warranty is still valid you should consider returning it to HTC maybe they might replace it
got the same problem. Any solution so far ??
ddotpatel said:
Sounds like its just a driver issue. Have you tried plugging it in, when you get that message open DEVICE MANAGER,... Find the yellow "!", right click it, uninstall, unplug phone, reboot PC.
.... Then use BTDAG's [Guide] How to Setup Correct Hero Drivers (for x86 & x64 users)
Click to expand...
Click to collapse
Did you try that?..... You need to do the reboot PC/Laptop after uninstalling ALL HTC drivers! Then when you reboot PC, plug phone back in, should say "not recognised" again,... then follow BTDAG's guide. T'is definitely a driver issue!
tried flashing 3 roms, modaco, radug and now kimera... none working.
can connect in fastboot, it shows up in device manager as android 1.0
ive tried 3 different usb cables and 4 differet pcs, still there is no response on my phone !!!
using villian rom 10.0 rite now.
okay it boots up into fastboot and fastboot usb shows up on the screen in red,
BUT when i use the "adb devices" command in adb it doesnt show the device,
it is showing as android 1.0 in devices and printers (windows 7)
You need to use....
fastboot devices
....when your are in fastboot.
What happens when you go into your recovery, select "Toggle MS/USB" with USB connected to PC?
okay
fastboot devices command shows some serial number.
then i tried adb remount, it gave an error....
enabling usb-ms with cable attached gives no response
ok i think it might be USB driver like ddotpatel said but i am not sure.
i reinstalled my whole windows 7 to 32bit now instead of the 64bit version i was using before and today i just connected my hero to my PC and windows 7 did its thing and installed the drivers and finally my hero can mount the SD card in my PC again although i kept getting this can perform faster in USB 2.0 port or something like that i didn’t care as long as i can mount my SD card again.
now went into fastboot and used the fastboot device command and i could see my hero serial no. but when i try to flash the amonra recovery i got the permission error (i cant really remember). i tried flashing using the adb method but still no luck.
so i went to market and downloaded rom manager and used it to flash clockwork recovery and now i could boot to clockwork recovery.
from this recovery i can now flash any rom i want and although there are still a few more problems i am glad now that i can flash custom roms again.
the problem i can see so far but i can deal with is
1. i don’t think fastboot commands work even if the phone is detected.
2. SD card mounts at USB 1.1 speed. (i have tried different ports and cable but still the same thing and this is the ports i use for my N1, Desire and my other android phones with USB 2.0 speed)
PS: adb commands for pushing and removing apps is working.
Hope this can be helpful to those experiencing the same problem.
Instead of re-installing your entire OS just use usbdeview to remove the failing drivers.
Also remove any old HTC Sync installs and install the latest version.
Related
Hey guys, I'm trying to update the VOID rom from Delta to Charlie and I'm using my PC now. I'm trying to toggle it to USB mode but it's not recognized on my PC. I usually do it at my friend's place and it recognizes it perfectly but on my PC it doesn't.
When I plug it in, it says "LG Android USB Device - Not recognized" or "No Driver Found"
How do I go about fixing this? I've already wiped the data and everything, just need to put the zip file in.
Been trying to get a hold of my friend but he's got class until tonight, and I kinda wanna not be depending on him if I need to do stuff with my phone, so I might as well try to get the drivers on my PC.
Any help would be great
Ok, so I just found the most random fix.
I took out the SD card, kept the cover off, booted into recovery, put the SDcard back in and mounted it, toggle USB and it worked.
So random but it worked!
Magnetix said:
Hey guys, I'm trying to update the VOID rom from Delta to Charlie and I'm using my PC now. I'm trying to toggle it to USB mode but it's not recognized on my PC. I usually do it at my friend's place and it recognizes it perfectly but on my PC it doesn't.
When I plug it in, it says "LG Android USB Device - Not recognized" or "No Driver Found"
How do I go about fixing this? I've already wiped the data and everything, just need to put the zip file in.
Been trying to get a hold of my friend but he's got class until tonight, and I kinda wanna not be depending on him if I need to do stuff with my phone, so I might as well try to get the drivers on my PC.
Any help would be great
Click to expand...
Click to collapse
I had the same problem, and the fix was to install the LG USB driver from the microSD card included with the phone.
Hello people, I have the same problem.
It works well but when I go into recovery and I toggle USB nothing happens.
Where can I find the drivers?
Which driver do I have to uninstall?
paolog89 said:
Hello people, I have the same problem.
It works well but when I go into recovery and I toggle USB nothing happens.
Where can I find the drivers?
Which driver do I have to uninstall?
Click to expand...
Click to collapse
http://www.lg.com/sg/support/produc...rgetPage=support-product-profile-mobile-redux
Download the LG Mobile Support tool first ... from there you can download the LG USB Drivers ... Once they are installed, your SD card will be detected in recovery ..
Nothing to uninstall ... PM if you need help
Could also just put the microSD in a card reader and put the ZIP on that way
Hi guys, was having a few problems with my phone and decided that I'd flash the stock ROM again.
Went into ODIN as you do, and as I was flashing the stock ROM, for some reason or another I heard the disconnect/reconnect noise that Windows makes when you remove a device then FAIL came up in ODIN.
Now my phone's stuck with a phone connecting to a computer on the charge screen, it can't go into recovery mode but it can go into download mode.
Tried connecting it to my PC in download mode, and even though I've got the Samsung USB Drivers installed I get the 'USB Device Not Recognized' message, which means I can't flash the stock ROM in ODIN anymore.
Does anyone have any advice? Thank you.
JoshS2 said:
Hi guys, was having a few problems with my phone and decided that I'd flash the stock ROM again.
Went into ODIN as you do, and as I was flashing the stock ROM, for some reason or another I heard the disconnect/reconnect noise that Windows makes when you remove a device then FAIL came up in ODIN.
Now my phone's stuck with a phone connecting to a computer on the charge screen, it can't go into recovery mode but it can go into download mode.
Tried connecting it to my PC in download mode, and even though I've got the Samsung USB Drivers installed I get the 'USB Device Not Recognized' message, which means I can't flash the stock ROM in ODIN anymore.
Does anyone have any advice? Thank you.
Click to expand...
Click to collapse
Try installing samsung kies. The usb drivers are included.
princeownt said:
Try installing samsung kies. The usb drivers are included.
Click to expand...
Click to collapse
I have it installed, and I installed the USB drivers from the soft bricked sticky in this section. Neither have helped.
Hi!
Hi, you guys install ADB on your system? And also USB debugging mode on the phone?
Should be turned on which can be done by going to Settings>Applications>Development and select USB debugging.
Try this, for me its works
MafiaDroid said:
Hi, you guys install ADB on your system? And also USB debugging mode on the phone?
Should be turned on which can be done by going to Settings>Applications>Development and select USB debugging.
Try this, for me its works
Click to expand...
Click to collapse
I can't even turn the phone on at the moment. Only thing I can do is go into Download mode.
Help
Try this, take out the battery, then press and hold the ON button for 7-10 seconds (the longer the better). Reinsert the battery, then press ON button to start it. This is a soft reset, and wipes the temporary memory and empties all remaining power in the circuits. This helps on many phones and even laptops that won't start properly or show anything on screen.
If this does not work, try the next step. Again, do as above. But after inserting the battery, do not turn the phone on, but press and hold the ON button and the HOME button at the same time for 7-10 seconds. This is a hard reset, and works best if done after a soft reset. Just be sure the battery has at least some juice in it and isn't empty. If possible, try with another battery if this does not work.
Hope this helps!
Try going to device manager, you will probably find your device as an unrecognized device, uninstall the drivers, unplug and then plug it again and see.
if the prblm is hard then do a fresh installation of kies,device etec etc.....but if u have ur device in the device list on pc then first uninstall it...if possible try recovery mode and reset...
I tried everything you guys have suggested and none of that worked. Anyone else got any ideas?
Try everything (and I mean everything) on the following list. Given the problems you've had & that you've already tried some of these things, I'd try another PC. And if it doesn't work first go on another PC, then go thru the list & try everything on the 2nd PC.
*Ensure Kies & it's processes aren't running in Windoze task manager. Kill them if they are.
*Try different USB ports; you must be using a 'powered' or mainboard port.
*Try different USB cables (particularly the cable that came with the phone if you're not using it now)
*Try different versions of Odin (search on here/Google)
*Uninstall Kies, reboot, redownload & reinstall it, reboot, try the flash again. Also run Windoze Update.
*And if all this fails, try a different PC.
Tried all the above and a different PC.
It didn't work. I could fix the phone if the computer would pick up that the phone's connected - it just doesn't.
Total Removal of KIES including registry entries .
Reboot PC install a new copy of Kies .
Phone backup data and factory reset .
Set phone to USB storage mode using the Samsung cable connect to PC and wait for Windows to find USB drivers .Remove cable reboot phone .
Start Kies connect with cable wait for Kies to find the phone .
Note USB Debugging OFF and cable connects to a direct motherboard port only .
Nothing then only further suggestion would be to Format the PC and start over with a clean Windows install .
jje
I can't turn the phone on, it's stuck on the phone, triangle, PC screen.
I've tried fresh installs on three different PC's.
JoshS2 said:
I can't turn the phone on, it's stuck on the phone, triangle, PC screen.
I've tried fresh installs on three different PC's.
Click to expand...
Click to collapse
That's a forced download mode.
Try a blind flash to a stock firmware from Odin while connected to your computer with the phone on this screen. Even if Odin doesn't seem to register that it's connected. I've heard of at least one person this worked for.
At this point, you really have nothing to lose by trying this.
Bit of an update, I plugged it in again and it installed some drivers and ODIN picked it up. Only for it to disconnect a few moments later, now it keeps disconnecting and reconnecting over and over but ODIN's not picking it up.
JoshS2 said:
Bit of an update, I plugged it in again and it installed some drivers and ODIN picked it up. Only for it to disconnect a few moments later, now it keeps disconnecting and reconnecting over and over but ODIN's not picking it up.
Click to expand...
Click to collapse
I know you said you tried a different cable, but that sounds suspiciously like a bad cable.
It's not the cable, thanks any way.
Update 2: I managed to get it to connect long enough to flash the stock Kernel. Still didn't reboot. Then I connected it again and flashed the stock ROM, which bricked it again. Then I flashed the stock kernel and it works!
However, there is a problem:
When the phone gets turned off, it constantly shows the charging battery icon with warning triangle and a thermostat next to it. I can't turn the phone on because of this unless I go into Recovery mode and reboot system.
Any ideas? Thanks.
JoshS2 said:
It's not the cable, thanks any way.
Update 2: I managed to get it to connect long enough to flash the stock Kernel. Still didn't reboot. Then I connected it again and flashed the stock ROM, which bricked it again. Then I flashed the stock kernel and it works!
However, there is a problem:
When the phone gets turned off, it constantly shows the charging battery icon with warning triangle and a thermostat next to it. I can't turn the phone on because of this unless I go into Recovery mode and reboot system.
Any ideas? Thanks.
Click to expand...
Click to collapse
Now this sounds like a faulty/dirty/bad usb port.
ctomgee said:
Now this sounds like a faulty/dirty/bad usb port.
Click to expand...
Click to collapse
This was my original thought and my reasoning for flashing a stock ROM in the first place!
JoshS2 said:
This was my original thought and my reasoning for flashing a stock ROM in the first place!
Click to expand...
Click to collapse
I in no way recommend this, and not sure I would do it if I ever started having this issue...
BUT - I have heard that some people faced with this condition have fixed it by physically moving the small wafer board inside the USB port with a precision screwdriver (gently!) to a more "centered" position.
If that doesn't work, look at replacing that part. Either via warranty service if you still have it, or a service center.
Firstly I apologise if this has been covered anywhere - I read a load of posts and did a load of searches but came up empty handed about this specific issue.
I bought a Galaxy Ace (GT-S5830 Baseband:S5830NEKA3 OS:2.2.1) as a dev device and it's been working fine up until today, and at some point it decided it doesn't want to be able to connect to my computers. I've tried three different computers, two different operating systems, and ever tried installing Kies (urk) with no luck.
The phone can charge over USB, saying that it's charging over AC, but that's all that happens.
I can't boot in to recovery mode as holding the power+middle button+vol up just gives me a ramdump message.
Can anyone help me out?
Martyn.h said:
Firstly I apologise if this has been covered anywhere - I read a load of posts and did a load of searches but came up empty handed about this specific issue.
I bought a Galaxy Ace (GT-S5830 Baseband:S5830NEKA3 OS:2.2.1) as a dev device and it's been working fine up until today, and at some point it decided it doesn't want to be able to connect to my computers. I've tried three different computers, two different operating systems, and ever tried installing Kies (urk) with no luck.
The phone can charge over USB, saying that it's charging over AC, but that's all that happens.
I can't boot in to recovery mode as holding the power+middle button+vol up just gives me a ramdump message.
Can anyone help me out?
Click to expand...
Click to collapse
When phone is turned off. Press and hold home+power/lock button untill it reaches recovery menu.
Check - that works. Thanks.
I'm now unsure as to how to proceed - neither adb devices nor fastboot devices are reporting anything back.
Connect device to pc. Open device manager (windows). Remove all drivers related to the ace and Samsung.
Remove the device and reboot the pc. Then connect the device. Windows update will detect the device and install the necessary drivers. If it doesn't automatically do that then open up device manager and install them manually by right clicking on the device and selecting update drivers from internet.
From the Galaxies to your Ace...!!
Thanks for your reply.
In windows there's no sign of any Samsung or Galaxy Ace drivers. Plugging it in to my Kubuntu machine gives me identical lsusb results as when not plugged in.
Have done a data wipe, checked that USB debugging is on and tried different cables
think it's screwed.
Think I could stick a ROM on the SD card and flash it? Would that work?
Martyn.h said:
Thanks for your reply.
In windows there's no sign of any Samsung or Galaxy Ace drivers. Plugging it in to my Kubuntu machine gives me identical lsusb results as when not plugged in.
Have done a data wipe, checked that USB debugging is on and tried different cables
think it's screwed.
Think I could stick a ROM on the SD card and flash it? Would that work?
Click to expand...
Click to collapse
hmm.. kies didnt work right? So i guess only option IMO would be card reader or CWM
Yep , the phone's USB port is frayed
This was sent from a Galaxy Ace. Problem?
Hi all,
I have a Rooted, WanamLite v6.3 ZSEMC1 ROM with AdamKernel 2.2.1+. i9300.
I updated recently from another previous version of the same ROM because I had noticed that my USB functionality has not been working. Specifically, the MTP application. Soon further found that my computer does not recognise ADB commands at all, as I used to install .apks from my computer quickly with adb install.
Odin does not even recognise my phone, even when in download mode. The only thing I havent tried yet is ADB in CWM Recovery, but im 99% sure that wont work still.
When I plug the micro-usb plug in it charges fine, but no data connection seems to occur. No windows detection, No USB device connected in the notifications bar.
I have tried:
-Backing up
-Installing vanilla ROM
-Installing stock ROM
-Using different computer with drivers
-Reinstalling Samsung Drivers
-Tried using Kies for the drivers
-Changing SD cards
-Power Cycling phone removing sim and micro-sd cards. Turning on after some time.
-Cleaning the micro-usb port on the phone with dental picks.
Im pretty much out of ideas apart from trying to organise to send it for repairs, after un-rooting.
If I was to re-root do you think this would solve the problem?
Any help is much appreciated.
Thanks :good:
UPDATE: I fixed this by using Mr. Despairs suggestion.
Power off, pull battery, SIM, SD card. Power cycled the power button with no battery in it.
Waited about 1-2 minutes.
Battery in boot straight to Download Mode.
Only got it to recognise once in about 15 tries.
Thanks again Mr Despair!
You could also try another cable. Or what I read in another german forum: Shut down your phone, take the battery out and in and reboot. Then reboot into download mode and plug in your phone. Then your PC should search for drivers.
Do this as a colleague says Mr. Despair replace the cable. Often dirt in the connector. Clean the connector on the phone.
Also check ...
Also check on a different computer/port - it could be a problem with the USB drivers on your computer.
Probably the safest test would be to cross-test combinations of 2-3 computers vs 2-3 phones.
xclub_101 said:
Also check on a different computer/port - it could be a problem with the USB drivers on your computer.
Probably the safest test would be to cross-test combinations of 2-3 computers vs 2-3 phones.
Click to expand...
Click to collapse
He already wrote that he tried more PCs. He would have very bad luck if it is on both. But trying doesn't cost. He shoule then also try to plug it direct into the USB ports and not through a hub.
I have also tried two other cables which both previously worked.
Ill give the hard reboot into download mode a try.
No PC recognises it at all at the moment.
I have tried all USB ports, directly not through a hub or whatnot. This includes other computers too.
Im open to any other suggestions.
Thanks for the help so far
Have you installed KIES?
KIES and ODIN cannot co-exist.
Install ONLY Samsung USB drivers then run ODIN.
As for installing apks, you shouldn't need to install via adb. You can just copy to sdcard and run from there.
Sent from my GT-I9300 using XDA Premium
IRPnet said:
Have you installed KIES?
KIES and ODIN cannot co-exist.
Install ONLY Samsung USB drivers then run ODIN.
As for installing apks, you shouldn't need to install via adb. You can just copy to sdcard and run from there.
Sent from my GT-I9300 using XDA Premium
Click to expand...
Click to collapse
I had used ODIN without KIES existing on my system.
I installed KIES to try and get it to read my phone for once.
I used ADB to install .apks when I had ADB running. I have the problem now that I cant use it, because my phone MTP, ADB or even Download Mode wont read my phone. All from different computers etc.
:crying:
Sounds more and more like a hardware failure. What about reboot to CWM then in mounts and storage to mount the USB drive? Can your PC recognize it this way?
Mr. Despair said:
Sounds more and more like a hardware failure. What about reboot to CWM then in mounts and storage to mount the USB drive? Can your PC recognize it this way?
Click to expand...
Click to collapse
Yeah im thinking hardware too. If I throw it into CWM and try to mount /sdcard, it doesnt to anything. Nothing changes it just stays permanently on mount /sdcard. (Its not mounting).
Mounting external_sd works but its not helping me.
Anyone ever returned a SGS3 to factory or phone provider?
Mr. Despair said:
You could also try another cable. Or what I read in another german forum: Shut down your phone, take the battery out and in and reboot. Then reboot into download mode and plug in your phone. Then your PC should search for drivers.
Click to expand...
Click to collapse
I initially tried this with no success, however after about 15 tries I got it to work once!
Thanks heaps for this!
Pull Battery, SIM and SD. Press Power buttons a few times and let it sit for about 1 minute.
Battery in and boot straight to Download mode. Worked once in about 15 tries. Reflashed everything and it works now!
Thanks Despair!!:laugh::laugh::laugh::laugh::laugh::laugh::laugh::laugh:
The titel says it all , and I need some help. I can still go in recovery but adb won't recongize my HTC, but I can still find it in fastboot. I formatted the sdcard, so I have nothing on there. Help would be much appreciated.
vsp33ddyv said:
The titel says it all , and I need some help. I can still go in recovery but adb won't recongize my HTC, but I can still find it in fastboot. I formatted the sdcard, so I have nothing on there. Help would be much appreciated.
Click to expand...
Click to collapse
Oh, trust me that's not your phone being bricked. You guys seriously need to know the correct vocabulary.
Bricking the phone: The phone's only use is to use it as a literal brick. It does not turn on, does not recover, does not charge, does not do anything and it can never be restored.
HOX+ can NOT be bricked unless you are S-Off'ed. Now that we got that out of the way,
you seem to understand that ADB is the solution here, that you need to sideload a rom, the question that you have is the adb does not recognize your phone, so follow these steps:
-Connect the phone using a different usb port, (basically thats the easiest thing), if its 2.0 then try 3.0 and vice versa.
-Restart your computer
-Restart your phone
-If you are on windows Vista and later, open start menu search for "cmd" then right click and run it as administrator, then you need to cd to your adb directory.
Code:
cd C:\Android\sdk\platform-tools
for example. then try adb devices.
Anyway hope you get it to work and have fun
Ghand0ur said:
Oh, trust me that's not your phone being bricked. You guys seriously need to know the correct vocabulary.
Bricking the phone: The phone's only use is to use it as a literal brick. It does not turn on, does not recover, does not charge, does not do anything and it can never be restored.
HOX+ can NOT be bricked unless you are S-Off'ed. Now that we got that out of the way,
you seem to understand that ADB is the solution here, that you need to sideload a rom, the question that you have is the adb does not recognize your phone, so follow these steps:
-Connect the phone using a different usb port, (basically thats the easiest thing), if its 2.0 then try 3.0 and vice versa.
-Restart your computer
-Restart your phone
-If you are on windows Vista and later, open start menu search for "cmd" then right click and run it as administrator, then you need to cd to your adb directory.
Code:
cd C:\Android\sdk\platform-tools
for example. then try adb devices.
Anyway hope you get it to work and have fun
Click to expand...
Click to collapse
The only thing I can do is use fastboot , thx for noticing that I know I need adb sideload If I look in devices on my PC I can see 'ONE' with a yellow triangle next to it ( so this means drivers) I downloaded my HTC drivers and I right clicked on the device and then update from PC , I go to the folder where I installed it and click on search and it says it can't find a driver for this device.
I also tried 4 different USB ports both 2.0 or 3.0 , no result. I also tried to install TWRP instead of cmw but on TWRP my touchscreen doesn't work while on cmw it does. So i went back and flashed my recovery to cmw again ( I tried version 2.6 - 2.7.0.1 , no result )
So my problem right now can be solved once my device can be recognized by my PC. (Have HTC maneger installed , also downloaded drivers formy phone , got fastboot and adb on my PC )
For anyone who knows thanks
vsp33ddyv said:
The only thing I can do is use fastboot , thx for noticing that I know I need adb sideload If I look in devices on my PC I can see 'ONE' with a yellow triangle next to it ( so this means drivers) I downloaded my HTC drivers and I right clicked on the device and then update from PC , I go to the folder where I installed it and click on search and it says it can't find a driver for this device.
I also tried 4 different USB ports both 2.0 or 3.0 , no result. I also tried to install TWRP instead of cmw but on TWRP my touchscreen doesn't work while on cmw it does. So i went back and flashed my recovery to cmw again ( I tried version 2.6 - 2.7.0.1 , no result )
So my problem right now can be solved once my device can be recognized by my PC. (Have HTC maneger installed , also downloaded drivers formy phone , got fastboot and adb on my PC )
For anyone who knows thanks
Click to expand...
Click to collapse
Hmmm. I would say in the device manager right click on the one and uninstall. Then in fastboot mode unplug and replug the device, let it install fastboot again and then try if adb can read it now.
Ghand0ur said:
Hmmm. I would say in the device manager right click on the one and uninstall. Then in fastboot mode unplug and replug the device, let it install fastboot again and then try if adb can read it now.
Click to expand...
Click to collapse
Still can't read it...
This has happened to my phone twice... fixed it the first time by using USB deview to remove all Android/HTC drivers, then reinstalled them with the HTC Sync installer. Couldn't get that to fix it last time though, so I tried another computer and it worked just fine. So my advice would be to find another computer and try it.
911jason said:
This has happened to my phone twice... fixed it the first time by using USB deview to remove all Android/HTC drivers, then reinstalled them with the HTC Sync installer. Couldn't get that to fix it last time though, so I tried another computer and it worked just fine. So my advice would be to find another computer and try it.
Click to expand...
Click to collapse
YES THIS IS WHAT WORKED ONLY I DID SOME OTHER STEPS TOO!!! Now I got adb running again and I can only push , I'll explain later in a full tutorial how to fix this now you guys can help me , I'm trying to download a cyanmod for my HTC because the stock is german and I can't download it , so can anyone upload the cyanmod endeavouru for me I keep getting error 502 bad gateway I almost fixed it !!!!! I need it badly !
OOkay so I thought I had figured it out , I uste TWRP to push files from PC to my Phone , then I installed cmw and tried to install the ROMS , but apperantly my roms were deleted. (I can't use TWRP because I need touch and the touch doesn't work , while in cmw the touch does work)
So if we can fix the TWRP touch I will know how to fix my problem !
I fixed the problem
I fixed the problem , thread how comming soon !
Here is my thread http://forum.xda-developers.com/showthread.php?p=52550145