Related
Hi all
I have a problem with my hero not being recognized by my PC. This happened after a weekend trip and i charged the phone with iphone USB adapter as i lost my one and now after returning from my trip i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message.
Also my Amon_Ra recovery i used has been wiped and i cant get into recovery or install any rom at all.
I am thinking this might be the same USB brick that affected some Desire owners but i am not sure.
So please if anyone can help me, please do.
Thanks in advance.
fizzle101 said:
Hi all
I have a problem with my hero not being recognized by my PC. This happened after a weekend trip and i charged the phone with iphone USB adapter as i lost my one and now after returning from my trip i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message.
Also my Amon_Ra recovery i used has been wiped and i cant get into recovery or install any rom at all.
I am thinking this might be the same USB brick that affected some Desire owners but i am not sure.
So please if anyone can help me, please do.
Thanks in advance.
Click to expand...
Click to collapse
this happen to me. What i did was switch my phone off, plug in the usb and switched it back on. then wait for windows to say it not recognised. then go to to device and printers and uninstall the drivers for the phone. Disconnect and reconnect the usb back to the phone and it it will pick it up.
Can you try booting in fastboot and tell me if that is recognized?
it still doesnt recognize it in fastboot
fc_Kuro said:
this happen to me. What i did was switch my phone off, plug in the usb and switched it back on. then wait for windows to say it not recognised. then go to to device and printers and uninstall the drivers for the phone. Disconnect and reconnect the usb back to the phone and it it will pick it up.
Click to expand...
Click to collapse
i have tried that and it doesnt help
fizzle101 said:
i connect my hero to my PC to be greeted with the "USB Device Not Recognized" message
Click to expand...
Click to collapse
Sounds like its just a driver issue. Have you tried plugging it in, when you get that message open DEVICE MANAGER,... Find the yellow "!", right click it, uninstall, unplug phone, reboot PC.
.... Then use BTDAG's [Guide] How to Setup Correct Hero Drivers (for x86 & x64 users)
I hav the same problem. In recover mode it works but then turn on the phone, there is no popup options as before. Tried around with drivers but didnt work either. But found a solution which is very convenient. I dont know if it works on other ROM versions but I'm on 2.1 (Villain10).
- Install extended control widget (dont remember where I got it but you can google, it seems I cannot find it on the market)
- Add this widget to the home screen: Menu/Add to Home/Widget/ Extended Control bar (you can choose the size from 1x1 to 1x4) then select "Mass storage" at the bottom, apply.
Now you have a widget to turn on/off USB storage. When you connect Hero to the PC, just click on this widget then the PC will connect to the SD card, and click one more to turn it off.
ok i will give that a try
crk23 said:
I hav the same problem. In recover mode it works but then turn on the phone, there is no popup options as before. Tried around with drivers but didnt work either. But found a solution which is very convenient. I dont know if it works on other ROM versions but I'm on 2.1 (Villain10).
- Install extended control widget (dont remember where I got it but you can google, it seems I cannot find it on the market)
- Add this widget to the home screen: Menu/Add to Home/Widget/ Extended Control bar (you can choose the size from 1x1 to 1x4) then select "Mass storage" at the bottom, apply.
Now you have a widget to turn on/off USB storage. When you connect Hero to the PC, just click on this widget then the PC will connect to the SD card, and click one more to turn it off.
Click to expand...
Click to collapse
that didnt work. o well i guess i am stock with the rom i have there.
fizzle101 said:
that didnt work. o well i guess i am stock with the rom i have there.
Click to expand...
Click to collapse
i've got this problem once and it was as simple as the cable was damaged...
i changed the cable and since then, everything works try that.
robocik said:
i've got this problem once and it was as simple as the cable was damaged...
i changed the cable and since then, everything works try that.
Click to expand...
Click to collapse
i have tried everything. changed the cable, used different pc but nothing works. i think is a hardware problem, something might be broken inside or something like that
Did you ever got this solved? I have the same problem only i use stock rom 2.1 Hero.. driving me nuts ...
baklap said:
Did you ever got this solved? I have the same problem only i use stock rom 2.1 Hero.. driving me nuts ...
Click to expand...
Click to collapse
No i havent and i gave up trying because i dnt think there is a fix for it. if yours is unrooted and the warranty is still valid you should consider returning it to HTC maybe they might replace it
got the same problem. Any solution so far ??
ddotpatel said:
Sounds like its just a driver issue. Have you tried plugging it in, when you get that message open DEVICE MANAGER,... Find the yellow "!", right click it, uninstall, unplug phone, reboot PC.
.... Then use BTDAG's [Guide] How to Setup Correct Hero Drivers (for x86 & x64 users)
Click to expand...
Click to collapse
Did you try that?..... You need to do the reboot PC/Laptop after uninstalling ALL HTC drivers! Then when you reboot PC, plug phone back in, should say "not recognised" again,... then follow BTDAG's guide. T'is definitely a driver issue!
tried flashing 3 roms, modaco, radug and now kimera... none working.
can connect in fastboot, it shows up in device manager as android 1.0
ive tried 3 different usb cables and 4 differet pcs, still there is no response on my phone !!!
using villian rom 10.0 rite now.
okay it boots up into fastboot and fastboot usb shows up on the screen in red,
BUT when i use the "adb devices" command in adb it doesnt show the device,
it is showing as android 1.0 in devices and printers (windows 7)
You need to use....
fastboot devices
....when your are in fastboot.
What happens when you go into your recovery, select "Toggle MS/USB" with USB connected to PC?
okay
fastboot devices command shows some serial number.
then i tried adb remount, it gave an error....
enabling usb-ms with cable attached gives no response
ok i think it might be USB driver like ddotpatel said but i am not sure.
i reinstalled my whole windows 7 to 32bit now instead of the 64bit version i was using before and today i just connected my hero to my PC and windows 7 did its thing and installed the drivers and finally my hero can mount the SD card in my PC again although i kept getting this can perform faster in USB 2.0 port or something like that i didn’t care as long as i can mount my SD card again.
now went into fastboot and used the fastboot device command and i could see my hero serial no. but when i try to flash the amonra recovery i got the permission error (i cant really remember). i tried flashing using the adb method but still no luck.
so i went to market and downloaded rom manager and used it to flash clockwork recovery and now i could boot to clockwork recovery.
from this recovery i can now flash any rom i want and although there are still a few more problems i am glad now that i can flash custom roms again.
the problem i can see so far but i can deal with is
1. i don’t think fastboot commands work even if the phone is detected.
2. SD card mounts at USB 1.1 speed. (i have tried different ports and cable but still the same thing and this is the ports i use for my N1, Desire and my other android phones with USB 2.0 speed)
PS: adb commands for pushing and removing apps is working.
Hope this can be helpful to those experiencing the same problem.
Instead of re-installing your entire OS just use usbdeview to remove the failing drivers.
Also remove any old HTC Sync installs and install the latest version.
Hi guys, was having a few problems with my phone and decided that I'd flash the stock ROM again.
Went into ODIN as you do, and as I was flashing the stock ROM, for some reason or another I heard the disconnect/reconnect noise that Windows makes when you remove a device then FAIL came up in ODIN.
Now my phone's stuck with a phone connecting to a computer on the charge screen, it can't go into recovery mode but it can go into download mode.
Tried connecting it to my PC in download mode, and even though I've got the Samsung USB Drivers installed I get the 'USB Device Not Recognized' message, which means I can't flash the stock ROM in ODIN anymore.
Does anyone have any advice? Thank you.
JoshS2 said:
Hi guys, was having a few problems with my phone and decided that I'd flash the stock ROM again.
Went into ODIN as you do, and as I was flashing the stock ROM, for some reason or another I heard the disconnect/reconnect noise that Windows makes when you remove a device then FAIL came up in ODIN.
Now my phone's stuck with a phone connecting to a computer on the charge screen, it can't go into recovery mode but it can go into download mode.
Tried connecting it to my PC in download mode, and even though I've got the Samsung USB Drivers installed I get the 'USB Device Not Recognized' message, which means I can't flash the stock ROM in ODIN anymore.
Does anyone have any advice? Thank you.
Click to expand...
Click to collapse
Try installing samsung kies. The usb drivers are included.
princeownt said:
Try installing samsung kies. The usb drivers are included.
Click to expand...
Click to collapse
I have it installed, and I installed the USB drivers from the soft bricked sticky in this section. Neither have helped.
Hi!
Hi, you guys install ADB on your system? And also USB debugging mode on the phone?
Should be turned on which can be done by going to Settings>Applications>Development and select USB debugging.
Try this, for me its works
MafiaDroid said:
Hi, you guys install ADB on your system? And also USB debugging mode on the phone?
Should be turned on which can be done by going to Settings>Applications>Development and select USB debugging.
Try this, for me its works
Click to expand...
Click to collapse
I can't even turn the phone on at the moment. Only thing I can do is go into Download mode.
Help
Try this, take out the battery, then press and hold the ON button for 7-10 seconds (the longer the better). Reinsert the battery, then press ON button to start it. This is a soft reset, and wipes the temporary memory and empties all remaining power in the circuits. This helps on many phones and even laptops that won't start properly or show anything on screen.
If this does not work, try the next step. Again, do as above. But after inserting the battery, do not turn the phone on, but press and hold the ON button and the HOME button at the same time for 7-10 seconds. This is a hard reset, and works best if done after a soft reset. Just be sure the battery has at least some juice in it and isn't empty. If possible, try with another battery if this does not work.
Hope this helps!
Try going to device manager, you will probably find your device as an unrecognized device, uninstall the drivers, unplug and then plug it again and see.
if the prblm is hard then do a fresh installation of kies,device etec etc.....but if u have ur device in the device list on pc then first uninstall it...if possible try recovery mode and reset...
I tried everything you guys have suggested and none of that worked. Anyone else got any ideas?
Try everything (and I mean everything) on the following list. Given the problems you've had & that you've already tried some of these things, I'd try another PC. And if it doesn't work first go on another PC, then go thru the list & try everything on the 2nd PC.
*Ensure Kies & it's processes aren't running in Windoze task manager. Kill them if they are.
*Try different USB ports; you must be using a 'powered' or mainboard port.
*Try different USB cables (particularly the cable that came with the phone if you're not using it now)
*Try different versions of Odin (search on here/Google)
*Uninstall Kies, reboot, redownload & reinstall it, reboot, try the flash again. Also run Windoze Update.
*And if all this fails, try a different PC.
Tried all the above and a different PC.
It didn't work. I could fix the phone if the computer would pick up that the phone's connected - it just doesn't.
Total Removal of KIES including registry entries .
Reboot PC install a new copy of Kies .
Phone backup data and factory reset .
Set phone to USB storage mode using the Samsung cable connect to PC and wait for Windows to find USB drivers .Remove cable reboot phone .
Start Kies connect with cable wait for Kies to find the phone .
Note USB Debugging OFF and cable connects to a direct motherboard port only .
Nothing then only further suggestion would be to Format the PC and start over with a clean Windows install .
jje
I can't turn the phone on, it's stuck on the phone, triangle, PC screen.
I've tried fresh installs on three different PC's.
JoshS2 said:
I can't turn the phone on, it's stuck on the phone, triangle, PC screen.
I've tried fresh installs on three different PC's.
Click to expand...
Click to collapse
That's a forced download mode.
Try a blind flash to a stock firmware from Odin while connected to your computer with the phone on this screen. Even if Odin doesn't seem to register that it's connected. I've heard of at least one person this worked for.
At this point, you really have nothing to lose by trying this.
Bit of an update, I plugged it in again and it installed some drivers and ODIN picked it up. Only for it to disconnect a few moments later, now it keeps disconnecting and reconnecting over and over but ODIN's not picking it up.
JoshS2 said:
Bit of an update, I plugged it in again and it installed some drivers and ODIN picked it up. Only for it to disconnect a few moments later, now it keeps disconnecting and reconnecting over and over but ODIN's not picking it up.
Click to expand...
Click to collapse
I know you said you tried a different cable, but that sounds suspiciously like a bad cable.
It's not the cable, thanks any way.
Update 2: I managed to get it to connect long enough to flash the stock Kernel. Still didn't reboot. Then I connected it again and flashed the stock ROM, which bricked it again. Then I flashed the stock kernel and it works!
However, there is a problem:
When the phone gets turned off, it constantly shows the charging battery icon with warning triangle and a thermostat next to it. I can't turn the phone on because of this unless I go into Recovery mode and reboot system.
Any ideas? Thanks.
JoshS2 said:
It's not the cable, thanks any way.
Update 2: I managed to get it to connect long enough to flash the stock Kernel. Still didn't reboot. Then I connected it again and flashed the stock ROM, which bricked it again. Then I flashed the stock kernel and it works!
However, there is a problem:
When the phone gets turned off, it constantly shows the charging battery icon with warning triangle and a thermostat next to it. I can't turn the phone on because of this unless I go into Recovery mode and reboot system.
Any ideas? Thanks.
Click to expand...
Click to collapse
Now this sounds like a faulty/dirty/bad usb port.
ctomgee said:
Now this sounds like a faulty/dirty/bad usb port.
Click to expand...
Click to collapse
This was my original thought and my reasoning for flashing a stock ROM in the first place!
JoshS2 said:
This was my original thought and my reasoning for flashing a stock ROM in the first place!
Click to expand...
Click to collapse
I in no way recommend this, and not sure I would do it if I ever started having this issue...
BUT - I have heard that some people faced with this condition have fixed it by physically moving the small wafer board inside the USB port with a precision screwdriver (gently!) to a more "centered" position.
If that doesn't work, look at replacing that part. Either via warranty service if you still have it, or a service center.
my phone will not be recognized by the computer no matter what i do. It recognizes my friends i777 just fine in odin and as a storage device so it isnt my drivers. With mine it only makes the connection sound and says device drivers failed to install. I am running shostock 3, philz kernel and windows 7. I have tried everything and i am out of ideas, please help. thanks
Install Kies fresh, install android sdk and update it, reboot, try different usb ports.
Also u have to disable usb debugging and let it install those drivers, enable it and let it install those drivers and boot into download mode and do a regular reboot and let it install those. Always worked for me after following those steps.
If he's friends phones works. Then I think it's the phone usb. My own phone has the same issues but my usb on phone is messed up. Says charging while its not chargin and that happens I get the whole Device not recognize and fail to install. Try cleaning your usb with 99% Isopropyl of the instructions above this post don't work out.
chibixzero said:
If he's friends phones works. Then I think it's the phone usb. My own phone has the same issues but my usb on phone is messed up. Says charging while its not chargin and that happens I get the whole Device not recognize and fail to install. Try cleaning your usb with 99% Isopropyl of the instructions above this post don't work out.
Click to expand...
Click to collapse
I will try this. I appreciate the help
I tried the suggestions.....
I downloaded the samsung drivers correctly because my pc recognizes any other samsung but no matter what i've tried it says usb device not recognized for my galaxy. Im stuck in a boot loop and the only thing i can access is download mode when i plug it in the computer. I can't access anything with the battery in, it just flashes the galaxy logo over and over. Thank you for you time in advance
Hi all,
I have a Rooted, WanamLite v6.3 ZSEMC1 ROM with AdamKernel 2.2.1+. i9300.
I updated recently from another previous version of the same ROM because I had noticed that my USB functionality has not been working. Specifically, the MTP application. Soon further found that my computer does not recognise ADB commands at all, as I used to install .apks from my computer quickly with adb install.
Odin does not even recognise my phone, even when in download mode. The only thing I havent tried yet is ADB in CWM Recovery, but im 99% sure that wont work still.
When I plug the micro-usb plug in it charges fine, but no data connection seems to occur. No windows detection, No USB device connected in the notifications bar.
I have tried:
-Backing up
-Installing vanilla ROM
-Installing stock ROM
-Using different computer with drivers
-Reinstalling Samsung Drivers
-Tried using Kies for the drivers
-Changing SD cards
-Power Cycling phone removing sim and micro-sd cards. Turning on after some time.
-Cleaning the micro-usb port on the phone with dental picks.
Im pretty much out of ideas apart from trying to organise to send it for repairs, after un-rooting.
If I was to re-root do you think this would solve the problem?
Any help is much appreciated.
Thanks :good:
UPDATE: I fixed this by using Mr. Despairs suggestion.
Power off, pull battery, SIM, SD card. Power cycled the power button with no battery in it.
Waited about 1-2 minutes.
Battery in boot straight to Download Mode.
Only got it to recognise once in about 15 tries.
Thanks again Mr Despair!
You could also try another cable. Or what I read in another german forum: Shut down your phone, take the battery out and in and reboot. Then reboot into download mode and plug in your phone. Then your PC should search for drivers.
Do this as a colleague says Mr. Despair replace the cable. Often dirt in the connector. Clean the connector on the phone.
Also check ...
Also check on a different computer/port - it could be a problem with the USB drivers on your computer.
Probably the safest test would be to cross-test combinations of 2-3 computers vs 2-3 phones.
xclub_101 said:
Also check on a different computer/port - it could be a problem with the USB drivers on your computer.
Probably the safest test would be to cross-test combinations of 2-3 computers vs 2-3 phones.
Click to expand...
Click to collapse
He already wrote that he tried more PCs. He would have very bad luck if it is on both. But trying doesn't cost. He shoule then also try to plug it direct into the USB ports and not through a hub.
I have also tried two other cables which both previously worked.
Ill give the hard reboot into download mode a try.
No PC recognises it at all at the moment.
I have tried all USB ports, directly not through a hub or whatnot. This includes other computers too.
Im open to any other suggestions.
Thanks for the help so far
Have you installed KIES?
KIES and ODIN cannot co-exist.
Install ONLY Samsung USB drivers then run ODIN.
As for installing apks, you shouldn't need to install via adb. You can just copy to sdcard and run from there.
Sent from my GT-I9300 using XDA Premium
IRPnet said:
Have you installed KIES?
KIES and ODIN cannot co-exist.
Install ONLY Samsung USB drivers then run ODIN.
As for installing apks, you shouldn't need to install via adb. You can just copy to sdcard and run from there.
Sent from my GT-I9300 using XDA Premium
Click to expand...
Click to collapse
I had used ODIN without KIES existing on my system.
I installed KIES to try and get it to read my phone for once.
I used ADB to install .apks when I had ADB running. I have the problem now that I cant use it, because my phone MTP, ADB or even Download Mode wont read my phone. All from different computers etc.
:crying:
Sounds more and more like a hardware failure. What about reboot to CWM then in mounts and storage to mount the USB drive? Can your PC recognize it this way?
Mr. Despair said:
Sounds more and more like a hardware failure. What about reboot to CWM then in mounts and storage to mount the USB drive? Can your PC recognize it this way?
Click to expand...
Click to collapse
Yeah im thinking hardware too. If I throw it into CWM and try to mount /sdcard, it doesnt to anything. Nothing changes it just stays permanently on mount /sdcard. (Its not mounting).
Mounting external_sd works but its not helping me.
Anyone ever returned a SGS3 to factory or phone provider?
Mr. Despair said:
You could also try another cable. Or what I read in another german forum: Shut down your phone, take the battery out and in and reboot. Then reboot into download mode and plug in your phone. Then your PC should search for drivers.
Click to expand...
Click to collapse
I initially tried this with no success, however after about 15 tries I got it to work once!
Thanks heaps for this!
Pull Battery, SIM and SD. Press Power buttons a few times and let it sit for about 1 minute.
Battery in and boot straight to Download mode. Worked once in about 15 tries. Reflashed everything and it works now!
Thanks Despair!!:laugh::laugh::laugh::laugh::laugh::laugh::laugh::laugh:
Hi all, I will try to be as detailed as possible.
I have a MetroPCS LG MS323 which I bought as a second phone to use when I travel as my regular phone is CDMA and I wanted a GSM phone that I could use with a sim card. While on an overseas trip I paid a cellphone place to unlock the phone so I could use other carriers' sim card, it was working fine since then. However, as I don't use the phone on a regular basis it ended up sitting and the battery lost its charge. When I tried to charge it by usb, it started bootlooping (vibrate, LG logo, repeat). After that I pulled the battery and charged it using an external charger. The phone is not rooted. I tried the factory reset key combo, but it gets stuck on the screen which says factory reset processing........ endlessly. I tried to download kdz file and flash with LG flash tool but phone cannot get into download mode. When I press vol key and plug usb cable, it says LOADING.......... press volum up key until download mode starts But it gets stuck there and download mode never starts.
I downloaded adb and fastboot to a Windows 7 laptop, and LG drivers, but when I connect phone and open a terminal adb devices shows no phone connected.
I also downloaded Laf.img for this phone and Laf recovery tool for Windows but again I cannot seem to get computer to see the phone. If I try to use the tool it says "waiting for device"
One difficulty is to trying to plug phone to computer the right way.
Most of the threads say to have phone in battery charge mode with usb debugging enabled, but I can't select any settings if the phone is bricked.
If I just plug the phone to usb when it is turned off it shows a picture of battery but no sign of charging, and computer doesn't detect phone.
If I plug phone to usb first, then hold vol and power key the LG logo will go black and it vibrates, in that case sometimes the Windows laptop will see 2 folders, verinfo and image.
When I plug usb cable to Linux computer and phone is off, same thing just picture of battery but terminal only shows sda1 sda2 sda3 etc no sdb no sdc just like not detected.
If I hold vol down then plug usb it vibrates and stuck on LG logo.
I have also tried to plug usb, then press vol down and power until phone vibrates, then try to let go buttons before LG logo shows up. but it doesn't mount.
If I hold vol up and power, then plug usb. it vibrates and goes to LG logo.
Last night somehow I got it to mount on the linux computer but the file manager was going crazy opening multiple windows and a list of folders would show up for a second, disappear and reappear as if the system was trying to read the folders but having difficulty. Today I am not able to get it to mount.
I have downloaded a linux livecd with adb and fastboot, I haven't tried it yet because I am not sure the path to flash an img file from a different directory on the hard drive on the windows laptop.
I have downloaded aboot.img but don't know how I can flash it if I can't see the phone on any computers.
I have spent days searching for solutions but have not seen the exact same problem, other threads suggest things but often the symptoms are slightly different or with a different phone. So, first of all I need to know what kind of brick I have, because other solutions I have seen posted for completely black screen, or phone detected as qhsusb qualcomm etc. which seems like a different problem.
So the 2 main things are 1, to know which kind of brick because many of the solutions I see posted seem like a different problem.
second, what is the best way to plug to computer so I can see the phone?
I burned a live CD of FWUL and ran adb from linux, still says adb devices nothing shows up. usb cable is plugged in and phone is turned off. Am I doing this wrong? I held down power and vol down until phone vibrates and LG logo appears. adb devices - "list of devices attached" still has nothing showing.. I don't know why even in Linux I can't see any device attached. Also I tried with pressing vol up and power until phone vibrates.
ls /dev/sd* only shows sda sda1 sda2 etc
I have also looked at past threads about unlocking the L70 bootloader, but the bootloader.zip no longer links and the phone does not have busybox installed.
I tried to see it Windows Device Manager but it does not show up anywhere.
This probably won't help, but, when you're at this point, you'll try about anything.
Did you fully install the LG drivers on your PC? Obvious seeming question. I was doing an old Droid Bionic a couple months ago and didnt' switch the USB modes (charging, media, file transfer, whatever it had) to each mode before modding .
As a result, I bricked that Droid bad. It took me almost a week and a half to restore it. I'm not sure if LG drivers work the same way, though I've worked on plenty of them. I think I have an LG Leon still in the scrap heap as a result of trying to replace a cracked digitizer that was bonded to the LCD. If anyone needs parts for one, I've got em, cheap I think that's an MS345 if I recall.
equitube said:
This probably won't help, but, when you're at this point, you'll try about anything.
Did you fully install the LG drivers on your PC? Obvious seeming question. I was doing an old Droid Bionic a couple months ago and didnt' switch the USB modes (charging, media, file transfer, whatever it had) to each mode before modding .
As a result, I bricked that Droid bad. It took me almost a week and a half to restore it. I'm not sure if LG drivers work the same way, though I've worked on plenty of them. I think I have an LG Leon still in the scrap heap as a result of trying to replace a cracked digitizer that was bonded to the LCD. If anyone needs parts for one, I've got em, cheap I think that's an MS345 if I recall.
Click to expand...
Click to collapse
Thanks, yes I had installed latest LG drivers LGMobileDriver WHQL Ver 4.2.0 before trying to flash .kdz file.
A tiny bit of progress to report, after getting a perfect timing to release the power and vol down keys I was finally able to connect to Windows machine. while waiting for drivers to install it was detected as QHSUSB_BULK in device manager, after drivers loaded now it is listed as LGE AndroidNet USB Serial {port (COM4). However when I run adb I still cannot see an attached device. I will look at solutions for the specific type of brick problem which has now been identified.
fofopuka said:
Thanks, yes I had installed latest LG drivers LGMobileDriver WHQL Ver 4.2.0 before trying to flash .kdz file.
Click to expand...
Click to collapse
What I meant was after initially installing the drivers did you switch the USB mode on your LG to all possible settings? Some drivers (like Moto) install more functions only when first called. you'll know if you switch from say charging to MTP or RNDIS you'll see driver install reopen.
also when you first ran ADB and plugged in the phone you probably should have seen more drivers install.
Forgive me if I seem to insult your intelligence. I'm an IT pro w 30 yrs in tech and I didn't know about the multi driver USB functions.
Tom Sgt aka Rootjunky has a good video on this that i initially didn't watch figuring I'd been installing drivers forever. 5 more minutes of watching it would have saved near 40 hrs of work and research
and when r
equitube said:
What I meant was after initially installing the drivers did you switch the USB mode on your LG to all possible settings? Some drivers (like Moto) install more functions only when first called. you'll know if you switch from say charging to MTP or RNDIS you'll see driver install reopen.
also when you first ran ADB and plugged in the phone you probably should have seen more drivers install.
Forgive me if I seem to insult your intelligence. I'm an IT pro w 30 yrs in tech and I didn't know about the multi driver USB functions.
Tom Sgt aka Rootjunky has a good video on this that i initially didn't watch figuring I'd been installing drivers forever. 5 more minutes of watching it would have saved near 40 hrs of work and research
and when r
Click to expand...
Click to collapse
thanks, I found his video for the G2 and no, I have never seen that with the drivers before! good to know. You can't insult my intelligence because most of this is over my head and I'm just trying to follow stuff I found with Google on XDA......
I downloaded and installed the Qualcomm drivers to try and identify if I have the 9006 or 9008 variety brick. However now when I plug in the phone Windows waits to install drivers, then says successful, when I look in device manager now I can't find the phone. But I did notice on the taskbar now there appears an icon named "intel graphics media accelerator driver for mobile" perhaps that is the driver Windows assigned to it? Device manager does have Intel Graphics Media Accelerator under display adapters. The other weird thing is that now it shows the battery as charging, which it never did the other times I plugged it into usb.
fofopuka said:
thanks, I found his video for the G2 and no, I have never seen that with the drivers before! good to know. You can't insult my intelligence because most of this is over my head and I'm just trying to follow stuff I found with Google on XDA......
I downloaded and installed the Qualcomm drivers to try and identify if I have the 9006 or 9008 variety brick. However now when I plug in the phone Windows waits to install drivers, then says successful, when I look in device manager now I can't find the phone. But I did notice on the taskbar now there appears an icon named "intel graphics media accelerator driver for mobile" perhaps that is the driver Windows assigned to it? Device manager does have Intel Graphics Media Accelerator under display adapters. The other weird thing is that now it shows the battery as charging, which it never did the other times I plugged it into usb.
Click to expand...
Click to collapse
have you seen this thread.
https://forum.xda-developers.com/showthread.php?t=2773123
it has the firmware for your model links to drivers and the LG flash tool, (which is warned against newbies (what the hey, it can't get much worse, we were all newbies once, )
Can you boot into fastboot? if so, you could flash the firmware with that.
equitube said:
have you seen this thread.
https://forum.xda-developers.com/showthread.php?t=2773123
it has the firmware for your model links to drivers and the LG flash tool, (which is warned against newbies (what the hey, it can't get much worse, we were all newbies once, )
Can you boot into fastboot? if so, you could flash the firmware with that.
Click to expand...
Click to collapse
Hi, yes although those links no longer work I have found the drivers and flashtool elsewhere. If I try to run flashtool it cannot see the phone. I cannot get into fastboot, and download mode won't load. I cannot see the phone on any Linux machine. The most I can do it see the phone as E: Qualcomm MMC storage USB device in Device Manager, but no other details. Explorer can see 2 folders, image and verinfo. Is there anything I can do with these folders in Windows? adb and fastboot run from terminal still do not list any attached device. Windows did a search for drivers for QHSUSB_BULK, although in device manager it still says LGE AndroidNet USB Serial Port (COM5).
What I really want to do at this point is push aboot.img to the phone, but for some reason I can't access the phone with Linux or adb. maybe because it did not have usb debugging enabled before it bricked. So many of the threads I have seen require a working phone to implement the steps, is there any way to enable usb debugging when the phone doesn't work?
fofopuka said:
Hi, yes although those links no longer work I have found the drivers and flashtool elsewhere. If I try to run flashtool it cannot see the phone. I cannot get into fastboot, and download mode won't load. I cannot see the phone on any Linux machine. The most I can do it see the phone as E: Qualcomm MMC storage USB device in Device Manager, but no other details. Explorer can see 2 folders, image and verinfo. Is there anything I can do with these folders in Windows? adb and fastboot run from terminal still do not list any attached device. Windows did a search for drivers for QHSUSB_BULK, although in device manager it still says LGE AndroidNet USB Serial Port (COM5).
What I really want to do at this point is push aboot.img to the phone, but for some reason I can't access the phone with Linux or adb. maybe because it did not have usb debugging enabled before it bricked. So many of the threads I have seen require a working phone to implement the steps, is there any way to enable usb debugging when the phone doesn't work?
Click to expand...
Click to collapse
Of course, I had forgotten about that. In order to use fastboot, most flashing tools, you HAVE to have USB debugging on.
There are occasional ways around this, though they are few. I do seem to recall oding it on that LG Leon. OR it may have been a Moto e or G, let me look back at previous threads i've asked for help in.
(Hmm, perhaps taking notes, or just leaving a webcam running while I'm doing a new device might be valuable in the future, I think with remarkable hindsight.) :cyclops:
---------- Post added at 02:28 AM ---------- Previous post was at 02:26 AM ----------
And no, you can't do anything to Android files in Windows, except see them. they are generally a different file system
One of the difficulties is just plugging it to a PC. 9 out of 10 times it is not recognized and nothing happens. So far the only way that seems to occasionally work is to plug the usb cable to the Windows 7 laptop, hold vol down and power, release both as soon as it vibrates. Most of the time I can't get it timed exactly right, but if I'm lucky sometimes Windows will detect the usb connection by following these steps. If I try on a Linux machine nothing happens, phone stays invisible. The most I've gotten with Linux is to charge the battery, but will not mount.
It is just a stock phone, not rooted, no busybox, no developer options enabled.