I have an HTC Droid DNA that I hope to get switched over to MetroPCS. I have done this several times so I thought it would be no problem, but then I ran into a problem. No program I have tried (QPST, CDMA Workshop, DFS) can connect through the com port. The drivers are installed correctly and I tried updating them to no avail. Tried different usb ports and cables. Tried uninstalling and reinstalling drivers. Uninstalling and reinstalling htc sync. When i go into qpst configuration to add the port it sees it but doesnt have any info and when i open the service programming it doesnt detect a phone at all. In CDMA workshop it connects to the port but when I try to read the info it just comes back with garbage data and it gives an error when I try to send the SPC. Also the "HTC 9K DEV" isnt installed but I've heard it has something to do with LTE so that shouldnt matter right? are there drivers for this? I've been searching but haven't found anything that helps :/ Any help appreciated...
ZERO16LIVES said:
I have an HTC Droid DNA that I hope to get switched over to MetroPCS. I have done this several times so I thought it would be no problem, but then I ran into a problem. No program I have tried (QPST, CDMA Workshop, DFS) can connect through the com port. The drivers are installed correctly and I tried updating them to no avail. Tried different usb ports and cables. Tried uninstalling and reinstalling drivers. Uninstalling and reinstalling htc sync. When i go into qpst configuration to add the port it sees it but doesnt have any info and when i open the service programming it doesnt detect a phone at all. In CDMA workshop it connects to the port but when I try to read the info it just comes back with garbage data and it gives an error when I try to send the SPC. Also the "HTC 9K DEV" isnt installed but I've heard it has something to do with LTE so that shouldnt matter right? are there drivers for this? I've been searching but haven't found anything that helps :/ Any help appreciated...
Click to expand...
Click to collapse
Are you running the stock ROM, what OS are you on, does this require adb? Just a few basic things. The DNA sometimes seems to have problems communicating so need to know some things.
Chyrux said:
Are you running the stock ROM, what OS are you on, does this require adb? Just a few basic things. The DNA sometimes seems to have problems communicating so need to know some things.
Click to expand...
Click to collapse
Sorry, I knew I forgot to put something haha. I was on the stock Rom, tried unrooted then rooted just in case. I'm on FactoryROM now with the same result. My os is win 7 ultimate and I don't believe it requires adb but it does work with adb. Man I hope I can get this working, I already love this phone...
Thanks
So I tried it on a fresh win7 installation and still nothing so im going to try a different version. I'm currently using version 2.7 build 362 what do you guys use? do you possibly have a link?
EDIT: Tried build 366 and its the same. I tried build 378 and it says APQ8064 under phone 0 for esn and phone number and banner are blank and when i try to connect it says "online connection error: unspecified error" but at least it sees the phone now... Is there like a special way you're supposed to connect this phone or something? I have been doing it the same way i did my HTC Droid Eris, HTC Evo Shift 4G, and HTC Evo 3D...
EDIT2: Just found out that APQ8064 is the model number for the Snapdragon processor in the Droid DNA so at least it is seeing the phone and recognizing it...
HTC Sync supposedly (I haven't tested this) causes interference with the communication you need for the rooting exploit. Maybe it's also causing interference with the programs you're trying to use.
Just a thought.
M0rtiferrimus said:
HTC Sync supposedly (I haven't tested this) causes interference with the communication you need for the rooting exploit. Maybe it's also causing interference with the programs you're trying to use.
Just a thought.
Click to expand...
Click to collapse
thanks, worth a shot.
I'm an idiot, all i had to do was install the driver for htc 9k diag and use that port instead... Wow, i feel dumb.
Merry Christmas and thanks for the help
EDIT: Nope nevermind still doesnt work...
Do you have USB debugging enabled?
yeah it is.. ugh I'm out of ideas...
Try turning USB debugging off. If that doesn't work, you could try resetting your phone.
If that still doesn't work, your computer may have downloaded faulty drivers. PM me and I can send you the ones from my phone, if you want.
M0rtiferrimus said:
Try turning USB debugging off. If that doesn't work, you could try resetting your phone.
If that still doesn't work, your computer may have downloaded faulty drivers. PM me and I can send you the ones from my phone, if you want.
Click to expand...
Click to collapse
I'll give it a shot. I don't think its the drivers though, I tried different ones just in case but these work with my other phones...
ZERO16LIVES said:
I'll give it a shot. I don't think its the drivers though, I tried different ones just in case but these work with my other phones...
Click to expand...
Click to collapse
I'm having the same issue. Did you ever figure it out? CDMA WS, DFS, and QPST aren't letting me write to the device.
Related
After I OTA'd the phone, I wanted to do something in QPST, so I hooked up the phone in diag mode (Debugging active and Dial Up Networking). The phone connected in diagnostic mode, but connected to a different port than before I had OTA'd it, and QPST wouldn't connect or recognize it anymore. Oddly, CDMA Workshop would connect, but still wouldn't read it.
Seeing as how the port it connected to was com port 8, I changed it to a lower port number (port number 2), because I had heard CDMA Workshop sometimes has issues with anything above port 6. Still no luck.
The weird thing is that the port I was using it on before I OTA'd (port 3) claimed it was still in use. In a last ditch attempt to get it working, I connected to port 3 anyway, and still had no luck.
Anyone have any ideas?
Please I need a solution.
Was the phone in dialup mode? Did you usbui to modem?
Sent from my DROIDX using Tapatalk
hondakorn said:
Was the phone in dialup mode? Did you usbui to modem?
Sent from my DROIDX using Tapatalk
Click to expand...
Click to collapse
Yep and yep.cdma workshop keeps saying failed.. Cannot read phone. Or some thing like that
Yep same here. I did a *22899 to try to remedy something else & now qpst won't see the phone. I uninstalled & reinstalled both qpst & the phone drivers & so far it's a no-go. Any ideas?
Sent from my SCH-I500 using XDA App
Whats the dif? between *228 and 22899? Im still not finding the answer to the problem, Ive even tried changing the cable.
dandog96 said:
Whats the dif? between *228 and 22899? Im still not finding the answer to the problem, Ive even tried changing the cable.
Click to expand...
Click to collapse
I was once told that *22899 was the same as *228, option 1 which reprograms the phone radio settings but when I did it yesterday it said it was in activation mode & the lock p/w was set. I rebooted & reran 228, option 1 cause I thought I had hosed it up & thats where my qpst trouble began.
Sent from my SCH-I500 using XDA App
garywojdan81 said:
I was once told that *22899 was the same as *228, option 1 which reprograms the phone radio settings but when I did it yesterday it said it was in activation mode & the lock p/w was set. I rebooted & reran 228, option 1 cause I thought I had hosed it up & thats where my qpst trouble began.
Click to expand...
Click to collapse
My prob. is when I plug it in to qpst it finds the com port but on the com port its says no phone.
Now I realized that its not limited to qpst, when I try to One-Click root it says Error Device Not Connected, Even when im on debug mode. So it seems to be a general usb prob. : /. This needs to be fixed.
This could have something with the ota causing mass storage to show up as a cdrom. Borked usb drivers in the ota it seems.
The only thing is I didn't update from the ota, I used Adrynalyne's modem, rom & kernel which he deodexed, debloated & rooted. Because of his work, I never had the cdrom problem & still don't; I can mount it as usb mass storage just like on di01. It's just that qpst won't see it, but everything else does.
update: Problem solved. Blade765 in the dev forum suggested booting the phone up while connected by usb with qpst open & it worked. As soon as it booted fully, qpst saw it & I was in. Oddly enough, the only value that was reset to the [email protected] and disabled was the #1 setting. The #0 setting was still enabled and still set to @vzw (no dun). Hope this helps...
Sent from my SCH-I500 using XDA App & 3g hotspot
garywojdan81 said:
The only thing is I didn't update from the ota, I used Adrynalyne's modem, rom & kernel which he deodexed, debloated & rooted. Because of his work, I never had the cdrom problem & still don't; I can mount it as usb mass storage just like on di01. It's just that qpst won't see it, but everything else does.
update: Problem solved. Blade765 in the dev forum suggested booting the phone up while connected by usb with qpst open & it worked. As soon as it booted fully, qpst saw it & I was in. Oddly enough, the only value that was reset to the [email protected] and disabled was the #1 setting. The #0 setting was still enabled and still set to @vzw (no dun). Hope this helps...
Sent from my SCH-I500 using XDA App & 3g hotspot
Click to expand...
Click to collapse
Great to know your fixed. Ill try this after work. Can you please explain to me what is a dun file, as I am a newbie.
.dun is stands for dial up networking and it is the value that directs your connection to the billing pipeline. So the goal is to change the first two entries in the service programming mode from "[email protected]" to "[email protected]" in order to keep your connection in the unlimited smartphone data pipeline which you're already paying for.
Sent from my SCH-I500 using XDA App
Well. Unfortunately it seems we have dif. problems because that solution does not work : (.
Can you try a different cable? Many othe micro usb cables are compatible.
Sent from my SCH-I500 using XDA App
Yea, Qpst worked before. Its just at one point it just stopped connecting. Ive tried three cables, same problem. Ive tried running qpst, and restarting the phone with the usb in, still doesnt help. I just dont understand. Same with the one-click root software. It worked before, but now it wont let me root, as it says my device is not connected.
Solution for this issue. Running out of options.
I have a Verizon fascinate,
hardware version i500.04,
firmware 2.1 update1,
build sch-i500.di01 ( i tried this with dl09 as well ).
When I check the box to see unknown qpst will see the ports but it will not see a phone on it. I have also searched a variety of different forums and have found other people with this issue but no resolutions other then to start with usb connected. Diagnostic mode is enabled and so is usb debugging. I have tried a variety of different combinations of settings with no luck.
Is there another solution for this issue other then booting with qpst and usb cable. Currently I have tried qpst with the following.
1: installing Samsung_Mobile_USB_Driver_V1.3.550.0_SCH-i500_Fascinate and rebooting.
2: installing SAMSUNG_USB_Driver_for_Mobile_Phones_x86.msi and rebooting
3: removing com ports and modem and reinstalling in every way i know how to.
4: used odin to flash back to dl01
5: Taken this to a fresh computer and installed only the fascinate drivers and qpst with no luck.
Any help would be greatly appreciated.
doctorslack said:
I have a Verizon fascinate,
hardware version i500.04,
firmware 2.1 update1,
build sch-i500.di01 ( i tried this with dl09 as well ).
When I check the box to see unknown qpst will see the ports but it will not see a phone on it. I have also searched a variety of different forums and have found other people with this issue but no resolutions other then to start with usb connected. Diagnostic mode is enabled and so is usb debugging. I have tried a variety of different combinations of settings with no luck.
Is there another solution for this issue other then booting with qpst and usb cable. Currently I have tried qpst with the following.
1: installing Samsung_Mobile_USB_Driver_V1.3.550.0_SCH-i500_Fascinate and rebooting.
2: installing SAMSUNG_USB_Driver_for_Mobile_Phones_x86.msi and rebooting
3: removing com ports and modem and reinstalling in every way i know how to.
4: used odin to flash back to dl01
5: Taken this to a fresh computer and installed only the fascinate drivers and qpst with no luck.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
Does rebooting the phone with QPST on help? It doesn't for me. Im on the verge of giving up.
I know this may sound stupid but do you have debugging on and dial up networking checked? Sorry if this is painfully obvious but I've found that most most of my troubles have come from details that I might've missed. Also, the reboot with the usb connected & qpst on is what did the trick for me.
Sent from my SCH-I500 using XDA App
garywojdan81 said:
I know this may sound stupid but do you have debugging on and dial up networking checked? Sorry if this is painfully obvious but I've found that most most of my troubles have come from details that I might've missed. Also, the reboot with the usb connected & qpst on is what did the trick for me.
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
Are you saying to disable those or make sure their enabled. I'm looking into performing the steps to get the work around for free mobile hotspots myself. Still doing a lot of reading as I'm new to Modding my phone but have learned a lot in the few days I've been teaching myself and was amazed at how easy a lot of this is especially with great guides on these forums and others.
Sent from my SCH-I500 using XDA App
I am trying to use QPST with a Samsung Fascinate and epic but i dont see my phones in com ports.(no phone)
Make sure you enable dun (dial up networking)...
Ive done that plus everything else im suppose to done yet no phone
pitokellie said:
Ive done that plus everything else im suppose to done yet no phone
Click to expand...
Click to collapse
Reinstall the drivers, attempt a different cord/port. Sometimes I'd have to fanboy plugged in. does the chomp recognize the phone or is it just qpst?
the phone is seen by comp and ive used cdma.idk
pitokellie said:
the phone is seen by comp and ive used cdma.idk
Click to expand...
Click to collapse
Okget the phone to be rec on the computer, then go into dun mode and reset the computer and load qpst. Use build 355 for everything except ppp...use build 215 for that.
QPST not detecting
Below is the ScreenShot
Kindly help
I have couple of phone with similar status
Has anyone been able to find a solution
The driver install fails on the HTC MTP driver install...I cannot get by this. I am running Windows 7 64 bit...anyone else having this issue?
OMG I fought with that for HOURS. I never did get them to work. I installed htc sync, htc sync manager, and I installed the all in one kit drivers.. Nothing. Windows 7 64 bit too.
I assume you are trying to unlock the bootloader and root?
Do both things manually using fast boot commands and recovery.
Tl;dr you can root without MTP drivers
wdkingery said:
OMG I fought with that for HOURS. I never did get them to work. I installed htc sync, htc sync manager, and I installed the all in one kit drivers.. Nothing. Windows 7 64 bit too.
Click to expand...
Click to collapse
exactly like me, I have been fighting with this for two days now. Reinstalling htc sync, htc sync manager, cleaning out existing drivers reinstalling again. Removing everything that could be associated with htc at all, reinstalling android sdk etc etc.
Nothing makes my phone recogniced by ´adb devices´not even htc sync software recognice it.
Every time I plug it in, the device is recogniced and installed and it says under Portable Devices in the device manager ´HTC One X+´
Do you get the Choose type of connection screen on your phone when connecting it? Because I dont, is just says connected in debug mode, even if debug development tools is turned of and debug of. But it still doesnt show up in adb.
denne2 said:
Do you get the Choose type of connection screen on your phone when connecting it?
Click to expand...
Click to collapse
No, not on this phone.. I think it has to do with the MTP crap. You can read an informative post by Lloir in the dev section to find out more.
wdkingery said:
No, not on this phone.. I think it has to do with the MTP crap. You can read an informative post by Lloir in the dev section to find out more.
Click to expand...
Click to collapse
hmm.
went back to the store and made them try connecting the phone to one of their laptops, if course everything worked perfectly there
So now im back trying to figure out what to do. Going to find the post you mention and see if I get any hints there.
Did you notice my post above where you I claimed you can root and unlock without the drivers?
What do you need to do that you need them?
Hi,
I am reading this, it is exactly what I recognize with my new One X+ too.
BUT I am not wanting to root or something. I'd like the Navigon software to recognize my device and download the maps like it did on my Desire HD.
Any more hints to how I can get this running ?
regards,
Ruud
I have a brand new bone stock dinc 4g lte.
I have activated sim and all features of phone work except when trying to connect via DIAG (##3424#).
Phone enters diag mode just fine.
USB debugging is enabled; Charge only is the PC connection.
My laptop is windows xp 32-bit.
I have installed the HTC Drivers: HTCDriver3.0.0.007
However, whenever I plug the phone in it recognizes new hardware: "Android Phone" and "HTC DIAG"
But after clicking "Install software automatically" it searches and then fails (even though I know the drivers are there).
When not in diag mode I can see my memory card and transfer files back and forth so I know part of the drivers are working.
What am I doing wrong?
*I found my own solution so I thought I'd post it just in case anyone else had my same problem.
1) I followed all the steps in the procedures listed in this thread, but needed to "disconnect my phone" before clicking "have disk".
This allowed me to successfully install drivers and connect to QPST. However.........
2) When I was connected QPST showed a question mark in front of my ESN. So I read and found that for this phone we need v2.7 build 3.74.
This did the trick!
3) I can verify that the "open sesame door" procedure works on this phone! Now can anyone confirm that it works for the Verizon HTC One also?
Read here
Thanks for replying so quickly! I'm glad to see you still use this phone.
I actually looked at that very thread before I started this one. QPST does not see the phone, so there aren't any phones listed when I try to add the port. So I can't click the "read phone" step in your directions because it's grayed out..
I've tried a different cable and different xp computer, and still can't load drivers!
Any other suggestions?
You should notice the diag drivers are not the same as the 3.0.0.007 drivers. Check that post I linked again.
Sent from my Incredible 4G LTE using Tapatalk 2
Are you talking about this link?
>When you have QPST installed Proceed to get your HTC Diagnostic Drivers, you can get them HERE
If so, that is what I've tried and hasn't worked.
Are there other driver download links in that thread I am missing?
I also tried all of the drivers you had stickied, but none worked.
This is very frustrating. Any other ideas?
supermaxkato said:
Are you talking about this link?
>When you have QPST installed Proceed to get your HTC Diagnostic Drivers, you can get them HERE
If so, that is what I've tried and hasn't worked.
Are there other driver download links in that thread I am missing?
Click to expand...
Click to collapse
Strange, I remembered the drivers posted to that thread being correct. In any case, a simple google search for "htc diag drivers" brings this up as the first result: http://forum.xda-developers.com/showthread.php?t=697487
If there is a thread with diag drivers then I've looked at it. So yes I looked at that post already. But maybe there is another way to connect to qpst without diag drivers? Or is it possble that I don't have something enabled correctly on this brand new phone?
Is there another way to create a virtual com port besides using dm router?
instead of automatic install have you tried doing it manually.
choose drivers, navigate to file, update driver?
synisterwolf said:
instead of automatic install have you tried doing it manually.
choose drivers, navigate to file, update driver?
Click to expand...
Click to collapse
Yes; I've followed this exact same process many times.
I just did it again (re-downloaded the files from the link you posted).
HIs instructions show windows 7 and I have xp, but it shouldn't matter.
When I choose his x86 drivers it always gives me this error:
HTC DIAG
When it finds new hardware "HTC DIAG" pops up in all caps.
Are drivers case sensitive?
Because all of the drivers I am manually choosing are lower case.
Could it be that is why they don't "contain information about my hardware?"
BTW, I have installed HTC diag drivers on this laptop (and my desktop) for my incredible 2 and have no problems connecting. So I'm struggling to understand why this one is so difficult!
Mine was for the evo LTE not the incredible LTE
Going home in a few, I'll see if I can get it to work and I'll report back.
Sent from my iPhone 5 using Tapatalk 4 beta
Thanks so much for your help!
Do you have a windows XP you can test it on?
I've tried 2 XP machines (both with SP3) and 2 different cables, but no luck.
I'm so glad people actually try to help on this forum (unlike some other forums).
It's been a few days; anyone able to help this phone work with windows xp? My incredible 2 was a breeze compared to this one.
Thanks to anyone who might be able to help!
Just picked up a Droid DNA off craigslist, does not have a sim card installed and i do not plan on putting one in. I bought it for use on wifi,play games and music. I am not going to use it as an actual phone. can anyone lead me to a current root method, would prefer a one touch or something simular, but ill take what i can get. lol.. also am i going to run into any problems not having a sim card installed? It is working fine now, just not sure how it will react to a factory reset or a root. thanks all
snakebyt said:
Just picked up a Droid DNA off craigslist, does not have a sim card installed and i do not plan on putting one in. I bought it for use on wifi,play games and music. I am not going to use it as an actual phone. can anyone lead me to a current root method, would prefer a one touch or something simular, but ill take what i can get. lol.. also am i going to run into any problems not having a sim card installed? It is working fine now, just not sure how it will react to a factory reset or a root. thanks all
Click to expand...
Click to collapse
Need to know what firmware you are on to help
To find this go to Settings >About >Software information >More >Build number
If you are on 3.xx you will use Rumrunner to S-off and unlock http://forum.xda-developers.com/showthread.php?t=2559232
If you are on 2.xx you will use Moonshine to S-off and unlock http://forum.xda-developers.com/showthread.php?t=2314771
Not having an installed SIM shouldn't cause any issues.
Have fun. :good:
build number is 1.15.605.4 cl123160 release-keys
how can i update that
snakebyt said:
build number is 1.15.605.4 cl123160 release-keys
how can i update that
Click to expand...
Click to collapse
Go to Moonshine link. There they will tell you how to update software to 2.xx and proceed to unlock.
Enjoy...
thanks for the help.. not the problem is that my pc will not recognise the phone no matter what i do, usb debugging is checked, but i plug the phone into pc i get nothing, i have tried 4 different usb ports and 3 different cords.. the phone will show charging, but the pc will not to anything.
i tried with and without htc sync installed
snakebyt said:
thanks for the help.. not the problem is that my pc will not recognise the phone no matter what i do, usb debugging is checked, but i plug the phone into pc i get nothing, i have tried 4 different usb ports and 3 different cords.. the phone will show charging, but the pc will not to anything.
i tried with and without htc sync installed
Click to expand...
Click to collapse
If you download PDANet on your computer it will install the correct drivers. Be sure to uninstall prior to Moonshine [uninstalling will leave the drivers].
Hope this helps, enjoy
usb debugging is selected
I went to build number and clicked on it and it did nothing, didnt hilight or anything to show it recieved any input from me.. i still pressed it about 200 times.. still nothing
installed pda net and still nothing when i connect it to the computer..
snakebyt said:
usb debugging is selected
I went to build number and clicked on it and it did nothing, didnt hilight or anything to show it recieved any input from me.. i still pressed it about 200 times.. still nothing
installed pda net and still nothing when i connect it to the computer..
Click to expand...
Click to collapse
What operating system is on you computer? Windows 8.1 can cause problems.
win 7
and my build number is 1.15.605.4 cl123160 release-keys would that be causing the problem
snakebyt said:
win 7
and my build number is 1.15.605.4 cl123160 release-keys would that be causing the problem
Click to expand...
Click to collapse
Hmmm, Okay. So when you go to "my computer" you don't see it as a drive at all?
Make sure your antivirus or firewall are not blocking it.
I'm trying to remember 1.xx software on my phone, been at least a year. Go to settings >security is there something in there like device administrators?
sdamark said:
Hmmm, Okay. So when you go to "my computer" you don't see it as a drive at all?
Make sure your antivirus or firewall are not blocking it.
I'm trying to remember 1.xx software on my phone, been at least a year. Go to settings >security is there something in there like device administrators?
Click to expand...
Click to collapse
It does have that option..i can chose android dwvice manager, agv antitheift,and air droid
snakebyt said:
It does have that option..i can chose android dwvice manager, agv antitheift,and air droid
Click to expand...
Click to collapse
Try Device Manager and see if that helps, and again make sure your antivirus or firewall are not blocking.
yes, when i plug in the phone to the PC it does nothing, no noise like when i plug in my ipod or a thumb drive or anything and it does not show up in my computer at all.
I have turned off the firewall on the PC and also turned off the antivirus.. will try turning off the antivirus on the phone and see if that helps
snakebyt said:
yes, when i plug in the phone to the PC it does nothing, no noise like when i plug in my ipod or a thumb drive or anything and it does not show up in my computer at all.
I have turned off the firewall on the PC and also turned off the antivirus.. will try turning off the antivirus on the phone and see if that helps
Click to expand...
Click to collapse
Sorry, but before we can go any further, you are going to have to get your computer to see your phone. I'm not sure what the problem is, but it seems hardware related. Every computer I've ever plugged my phone into started loading drivers and asked what I would like to do with this device [always select open and view files]. Be sure you are using a good cable [even though I've not seen a bad one, I have heard of them]. Try using another computer. Once you get the computer to recognize your phone, everything else will be simple.
Once again, have fun, and good luck.
I backed upeverything I needed to save using airdroid andgoing to do a factory reset and see if that helps anything
well i did a factory reset.. and still same thing...computer is not seeing the phone at all...really getting annoying
If you are still on software version 1.15.605.4 look for the S-OFF method called Facepalm it will work for 1.15.605.4.
if you are having trouble with windows 8.x and HTC drivers check this post
http://forum.xda-developers.com/showpost.php?p=49909454&postcount=43
If it will let you, install the 2.04 or 2.06 update. Try to contact to your computer after that. I remember that being a bug in 1.15 for me...
.torrented said:
If you are still on software version 1.15.605.4 look for the S-OFF method called Facepalm it will work for 1.15.605.4.
if you are having trouble with windows 8.x and HTC drivers check this post
http://forum.xda-developers.com/showpost.php?p=49909454&postcount=43
Click to expand...
Click to collapse
He can't get his computer to see his phone, that's the main problem. He's on Windows 7, so that's not the issue.
ryanguy426 said:
If it will let you, install the 2.04 or 2.06 update. Try to contact to your computer after that. I remember that being a bug in 1.15 for me...
Click to expand...
Click to collapse
He can't update OTA because he has no SIM.
Is there any place I can download the other.. I can use Airdroid to get a download on my phone and run it from there