[Q] how to unbrick mozart 7 - 7 Mozart General

i really need urs help im into trouble i had brick my cell now i cant unbrick my mozart wp7 see what i did
i use spl rspl hspl by dft and i use rspl to ospl 1st i had orignal botloader version 1.23 and now i got 1.32 i was using deepshine 2.0 after thet i successfully flash rom i went back to install a new rom its stuck on bootloader rom and sometime HTC logo in green color and vibrate few time no more windows just give me suggestion waiting for urs kind respnce
Regards
Mohsin Raza

Your Bootloader shows "HSPL1.32xxxx" in the first and "CotullaHSPLxxxxx" in the second Raw?
Then you can flash a Custom ROM .
If you has restored the "OSPL"back, then you only can flash Stock ROMS from your Provider.
Make a Hard reset first .

ok here is what i try alrady
i press power+vol up+down for a hard reset and press andykey to reset and 1st i install RSPL i have 1.23 bot loader then after installing rom successfull i got 1.32 what that mean after that i cant install any other rom and my firmwere has been bricked its stucked on HTC logo few imes vibrate

Again: You have HSPL or not ?

yes i have but no luck i guess i need to repair my spl downgrade back to 1.23 orignal spl but how? right now i have 1.32 i did everything

The HSPL Bootloader is 1.32 !
If you want to get back to original Bootloader you can restore it with the same Tool , only select "OSPL" before.
After that you can flash you Stock ROM from your Provider.
After this , you have the actual SPL from Stock ROM on your Phone ...

soory for a late responce but i did that alrady no luck now i had sent my htc to care center for unbrick and install a official rom...after that i will not stop doing exparement on my mozart but i will be careful next time thanx for urs advice thanx
Regards,
Mohsin raza

will you please PM me for how to get official ROM for my phone
OS version:7.10.8783.12
Firmware revision number: 2250.21.51303.401
Hardware revision number: 0004
Radio software version: 5.71.09.02a_22.51.50.21U
Radio hardware version: A.102.0.D4
Bootloader version: 5.13.2250.3(135167)
Chip SOC version: 2.2.5.0

Related

Help Me!

I Upgrade my O2 XDA II firm ware from ROM vesion 1.60.50WWE to 1.7.2.00 T-Mobile.
When upgrading to radio about 51% then has got a Error message ID 104 or 144 (I don't remember exacly) and guide include 4 step, summary access bootloader and reinstall.
I have reupgraded but received the same error.
after that I have downgraded the ROM vesion 1.60.50WWE but received the same error too.
Nowaday, My O2 can not start and I cann't doing any thing.
Help me.
Thank.
can you still get the boot loader screen or it's completely dead ?
If you still can, try flashing another ROM but after modifying the country code
Nowaday My O22 have been working, but I only use it with PDA function, no Telephone. Because process upgrade ware not completed. I was access boot loader and try reupgrade ROM with only radio stack many time, but any time upgrade when proccess write radio stack about 50% then Error. Although proccess erase radio no problem. I was try many other version ROM but the same error. If reboot O2, I must wait 20 minute It can working.
If enter Device Information:
ROM version: 1.72.00WWE
ROM date: 03/15/04
Radio version:
Protocol version:
ExtROM version:1.72.04
The boot loader version is 1.01
May have problem with hardware ?
Can have replace Flash ROM- Radio stack?
Thank You.
maybe it can work if you change your boot loader to 1.06
but now I haven't upgrade bootloader any time.
Can you help me how to change bootloader?
Thank!

hermes with tri color screen tried almost every thing

hi all,
i have recieved a hermes with boot loader screen (tri color) when i try to switch it on it goes directly to 2 color screen doesnt go further at all. I've read the sticky thread . As the phone which i have shows on screen the following
HERM100
IPL-1.04
HERM100
SPL-1.40. Olipro
thats it nothing else exept tri color screen so read the sticky threadabout how to unbrick hermes and did following options when i flashed tmobile uk rom it goes further but it stucks at 11% and doesnt go further and when i try to flash a rom which has 1.04 (528420-ruu_hermes_1[1].18.255.3_1.18.255.108_1.03.03.10_qtek_wwe_ship) but it doesnt do anything with phone, it cant even detect the phone and give error straight away can anyone please guide me what should i do further to alive this phone
UPDATE - To easily unbrick type 2b (on T-mobile UK) - please flash with wm6 test from t-mobile @ http://forum.xda-developers.com/showthread.php?t=322905
SPL HTC_BOOT Boot OS? No GSM? KITL Diagnostic Solution
1.04 Any No No --- Bricked while flashing OS, radio intact Flash any shipped ROM with bootloader 1.04 on it 2 times (1.04 bug)
hi no reply but 53 views any mod plz help
WHaT YOU MEAN?
by:
UPDATE - To easily unbrick type 2b (on T-mobile UK) - please flash with wm6 test from t-mobile @ http://forum.xda-developers.com/showthread.php?t=322905
SPL HTC_BOOT Boot OS? No GSM? KITL Diagnostic Solution
1.04 Any No No --- Bricked while flashing OS, radio intact Flash any shipped ROM with bootloader 1.04 on it 2 times (1.04 bug)
---I think your hermes is bricked if you cant upgrade even a stock rom is bricked dude...
For the last thing you could do about it... flash a stock rom like ATT stripped you can find it on the WM6 subforum here on hermes forums... all the chefs put in the main post the link to it... if it doesnt works so... you are screwed up...
be sure ahave this:
Battery at 100% at least 60%
XP pc not vista not wm7 ok?
A nice usb cable and nice USB ports too on the XP pc
Dont run anything till it finish and... dont flash with SIM card and microSD inserted.
Go ahead and post your results again.
hi thanks for your reply i have tried these 2 following roms
HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108 (stucks at 12%)
RUU_Hermes_CINGULAR_WWE_3[1].62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship (stucks at 11%)
with these its not really working anyother thing which u think i should do
br
Sounds like the radio rom is corrupted. Flash a Stripped Stock rom (no radio) . This should get you back up and running windows but it doesn't look good to get the phone running again...
mmmm
Sounds like your batt is almost dead... maybe it shows... 70% but drains to fast is lying to you... or your cable is broken somewhere...
you can DL the stock stripped here
http://www.4shared.com/file/61372397/e2bf76c0/official_ATT_WM6_striped.html
ultramag69 said:
Sounds like the radio rom is corrupted. Flash a Stripped Stock rom (no radio) . This should get you back up and running windows but it doesn't look good to get the phone running again...
Click to expand...
Click to collapse
yes u r right mate my phones radio rom was corrupted and thanks to + Que PPC for providing help and link of the official AT&T WM6 striped rom which turned my phone back to normal but the problem is when i went to device information it says like this
ROM version: 3.62.502.3
ROM date: 10/11/07
Radio version:
Protocol Version:
so radio and protocol versions are blank nothing is there so can u please tell me wt should i do to solve this or its not solvable at all thank you very much indeed to you guys. I really appreciate it
br Sherry
Not solvable... You might like to try running your SHIPPED STOCK Radio Rom, if you know what it is, but there isn't much hope of recovery once the radio goes... Look at it this way, couldn't hurt....

[Q] HTC Mozart spl 4.6 NoDO Update

Evening guys,
I have been reading a lot of threads regarding the Mozart and more particularly SPL 4.6 because I want to flash Deepshining.
I am now more confused than anything. NoDo flash/Y Cable...
So here is my phone build:
carrier orange uk
7.10.7740.16 soft
2250.21.40600.061 firmware
0004 hardware revision
5.69.09.05a radio software
A.102.0.D4 radio hradware
4.6.2250.0 boot loader
4.06.061.00 rom version
spl-4.6.2250.0 (129193) MNG
PD67100
And my question is can I flash a Nodo to downgrade the spl.
(RUU_Mozart_Orange_UK_1.30.401.01_Radio_5.54.09.21_22.33b.50U_NoDo_by_ansar)
Also is normal if when I run the rom update utility the "from version" field is blank
I hope you can help.
Thanks!
now have 1.22 but rspl not loading
Hi Finally tried and now have spl 1.22
I lashed this rom
RUU_Mozart_Orange_UK_1.22.061.10_Radio_5.50.09.18_22.24.50.09U_by_ansar
but now I can't manage to load rspl. The phone does not reboot automatically.
If you have any ideas...
Thanks
I sorted it!
I flash again using a different rom to get a different spl.
I then was able to load rspl.
I now have Deepshining
Hi can you give me brief details of exactly what you did please as i would like to do the same with my orange branded phone please.
regards
solution
Yep mate no problem
I first flashed my phone with a nodo rom
download and launch the exe shutdown your phone restart and hold “Volume Down” button during reset to enter OSPL mode....
located in this thread: http://forum.xda-developers.com/showthread.php?t=915827
in the middle of the page ou get this link from ansar
http://rapidshare.com/files/454244797/RUU_Mozart_Orange_UK_1.24.061.35_Radio_5.50.09.18_22.24.50.09U_by_ansar.zip
I fisrt tried version 1.22 but for some reason it would not allow the next step which is loading rspl and hspl the thread with the tools and tutorial is here:
http://forum.xda-developers.com/showthread.php?t=1195647
Reset your device and hold “Volume Down” button during reset to enter OSPL mode.
you first launch rspl it then restart the phone and you can load hspl. your boot should change to hspl 1.24....
with hspl you can now flash with any custom rom / unbranded rom.
Don't hesitate to ask me more If any doubt. You don't want to end up with a brick
\m/
question
one thing what is your bootloader version/spl version
as mine was 4.6.2250.0
the way of doing differs depending on that
If it is 4.x you can do like me I am not sure about 5.x and above anymore
thank you very much for the guide....very much appreciated. i hope now that i can load a custom ROM on my fone without bricking it!!
Details of my fone are:
OS vs:7.10.7740.16
Firmware rs: 2250.21.40600.061
Hardware rs:0004
Radio sfware:5.69.09.05A_22.50.50.21U
Radio hdware: a.102.0.d4
Boot lder: 4.6.2250.0
i'll download the bits now and give it a go 2moro.
many thanks
Thankyou very much for the guide....I now have a custom rom installed on my fone with the tango update. Cant believe how easy it was....when you know how that is!
Thanks again much appreciated. and if anyone else asks the question in the future i'll gladdly point them to this post.
regards
Orange Unbrand Help
Hi Guys,
I'm trying to un-brand and custom flash my ROM so to release the tethering feature on the Mozart 7. I'm pretty new to flashing WP7 handsets so would really appreciate your advice and guidance.
Details:
(across red banner it reads Security Unlocked)
PD67100 SS-BC (4K)
SPL-4.6.2250.0
TOUCH C1(v66)
OS Version: 7.10.7720.68
Firmware Number: 2250.21.40600.061
I'm currently downloading the following ROM following your instructions above;
RUU_Mozart_Orange_UK_1.24.061.35_Radio_5.50.09.18_22.24.50.09U_by_ansar.zip
Once this has completed I guess i run the update utility in the zip to flash the Mozart and run through the DFT HSPL RSPL WP7F3 tutorial you mentioned above however I'm confused on the next steps as I then want to update to Mango so do I need to re-flash with a custom ROM (unbranded) to will enable tethering, do you guys have any recommendations?
I downloaded this RUU_Mozart_HTC_Europe_1.30.401.01_5.54.09.21_22.33b.50_RELEASE however I'm not sure if this is right!!
worried I might brick my phone

[Q] 7.10.8112.7 failure. Continually Rebooting. Phone not working

I had a reliable debranded Mozart which has been unlocked by Orange in the UK and was running the ansar rom. It has accepted many updates in the post (post debranding) via Zune.
Unfortunately the 7.10.8112.7 update was problematic with error codes C1010007 and then C101002E.
I am left with a useless phone. I have done a factory reset to no avail.
The phone will boot into wp7.5 and sometimes holds for a few minutes before rebooting. Other times it gets into a loop while booting and ends up vibrating 7 times.
Any ideas anyone?
Is a fresh rom likely to help and if so which one?
I am currently showing:
OS 7.10.8107.79
Firmware 2250.21.51201.401
HW Rev 0004
SPL 5.12.2250.1
Thanks in advance
An Update
I have now dne a successful factory reset. Achieved this by leaving the battery out over night. I have been here before and am pretty sure that I will struggle to apply the above update.
Any suggestions would be appreciated.
desmo992 said:
I had a reliable debranded Mozart which has been unlocked by Orange in the UK and was running the ansar rom. It has accepted many updates in the post (post debranding) via Zune.
Unfortunately the 7.10.8112.7 update was problematic with error codes C1010007 and then C101002E.
I am left with a useless phone. I have done a factory reset to no avail.
The phone will boot into wp7.5 and sometimes holds for a few minutes before rebooting. Other times it gets into a loop while booting and ends up vibrating 7 times.
Any ideas anyone?
Is a fresh rom likely to help and if so which one?
I am currently showing:
OS 7.10.8107.79
Firmware 2250.21.51201.401
HW Rev 0004
SPL 5.12.2250.1
Thanks in advance
Click to expand...
Click to collapse
Like many other Users of that fu**ed Phone !
Iv got 2 of that Mozarts, one with the reboot and second without.
Its a Hardware Problem. Both Phones have the same ROM , changing Batteries ,changing SDCard, no Matter
it stays; the first reboots , the second never...
Update on Rebooting
Here is an update of my rebooting issue:
Following a factory reset (battery left out overnight) the phone is not longer rebooting PROVIDED THAT ID DO NOT CONNECT TO A WIRELESS NETWORK OR ATTEMPT TO APPLY AN UPDATE VAI ZUNE.
I am also able to get into the bootloader (spl5.12.2250.1) and establish a USB connection.
I do not want to mess with rolling back the bootloader as that seems to be a very high risk undertaking.
My suspicion is that a fresh rom installation may sort the problem as it only appeared after applying an update.
So can anyone suggest options for updating to a new reliable rom which will not consume excessive battery life - or at least point me in the right direction for one which is compatible with my current spl.
Thanks in advance.
Mike
desmo992 said:
Here is an update of my rebooting issue:
Following a factory reset (battery left out overnight) the phone is not longer rebooting PROVIDED THAT ID DO NOT CONNECT TO A WIRELESS NETWORK OR ATTEMPT TO APPLY AN UPDATE VAI ZUNE.
I am also able to get into the bootloader (spl5.12.2250.1) and establish a USB connection.
I do not want to mess with rolling back the bootloader as that seems to be a very high risk undertaking.
My suspicion is that a fresh rom installation may sort the problem as it only appeared after applying an update.
So can anyone suggest options for updating to a new reliable rom which will not consume excessive battery life - or at least point me in the right direction for one which is compatible with my current spl.
Thanks in advance.
Mike
Click to expand...
Click to collapse
Dear,
It seems that during update you phone might have low battery or update is interrupted.
You can install offical rom containing 201 search in file factory.
Otherwise go with the below, but you will need to downgrade your spl which is a lengthy process.
http://forum.xda-developers.com/showthread.php?t=1837393
Update to my last update
Thanks for your reply adeebulrehman
1. In your opinion, what are the merits of each of the two roms you suggest?
2. Can you suggest where I download the official rom safely?
3. Can you point me in the right direction for some safe and reliable spl downgrade instructions?
Many thanks
Mike
Karlitos
HI am new to this site and pls i want an advice on what to do on my htc hd7 WM 7.5 (upgraded yesterday)
well since i add the phone had problem with an error msg dat says (couldnt connect with my phone) when ever i sign in into my window live account.
secondly i was able to use same account id to sign in on my computer to download games and application but dnt know how to transfer dem to my phone...............
lastly i wish to switch to install android on my HTC hd7 as i did to my htc hd2..............but seems der is no hack to that.
below is the spec of my phone
name: karlitos
model: HTC HD T9292
software: win 7.5
total storage 14.64gb
available: 13.56gb
os version: 7.10.7740.16
firmware version no.: 2250.21.51004.401
hardware version no.: 0002
radio software version: 5.71.09.02a_22.51.50.21U
radio hardware version: A.102.0.D4
bootloader version: 5.10.2250.0(132968)
chip Soc version: 2.2.5.0
thanks ...................
desmo992 said:
Thanks for your reply adeebulrehman
1. In your opinion, what are the merits of each of the two roms you suggest?
2. Can you suggest where I download the official rom safely?
3. Can you point me in the right direction for some safe and reliable spl downgrade instructions?
Many thanks
Mike
Click to expand...
Click to collapse
Dear,
Just Search Mozart Shipped Rom That matches your firmware revision number last 3 number of third section.
2250.21.40600.061
For downgrading SPL there are details post of our Forum Moderators kindly read. All these are safe method unless you make a mistake

[Q] HTC Radar HSPL2.5 F400 error

Please Help ! I read lots of pages in forum, but can't find what I'm doing wrong. I want to get HSPL working to able to instal custom ROM to use Nokia apps, witch are way better than HTC and Marketplace apps.
Phone, HTC Radar 4G T-Mobile US
Windows Phone 7.8 (pushed on update with seveneight tool)
OS Version 7.10.8858.136
Firmware vers. 1600.2200.20402.531
Hardware revision: 0002
Radio vers. 16.23.05.13_16.30.00.23U
Radio hardware vers. 2.16.0.D4
Bootloader vers. 2.5.160015.3(137079)
Here is what I did, I flashed using Goldcardtool with Y-cable, OMEGIMG.nbh. I think flash did not finished properly, it went too fast, phone rebooted to SPL , plugged in to PC used DFT_HSPL_WP7SG1_INSTALL, install finished OK , but when I boot up to HSPL mode it does NOT connect to PC.
(Using ROMUpdateUtility getting connection error (260))
Here is how my screen looks in HSPL mode;
PI06110
HSPL2.5 1600.3(137079)
eMMC SMS 7376,FA31
CotullaH(F:80,ID:10,V20,B:AA)
Radio-16.23.05.13_2
F400
Please Help, what I'm doing wrong ? Why my HSPL have F400 error ?
Thank You so much !
Problem fixed. After HSPL install needed second time boot to USB Host mode and this time radio installed correctly. All good now, time for custom ROM
newappz said:
Problem fixed. After HSPL install needed second time boot to USB Host mode and this time radio installed correctly. All good now, time for custom ROM
Click to expand...
Click to collapse
Flash the radio also.

Categories

Resources