[Q] Error Code 33 - radio fail. What did go wrong? - HTC Radar

Hi xda-community,
I am new to the Smartphone- and the Windows Phone world. My main cause is to get rid of the swisscom branding of my HTC Radar. But I also would really like to test some custom ROMs - especially the Dynamics HD2O looks promising in my mind. That's why I bought all the equipment necessary for Goldcard method for 2nd Gen WP7 phones as in this manual.
My Info:
HTC Radar C110e
Model ID: PI06100
SPL – 1.8. 160015.3 (131745)
Radio-16.23.06.10
Radio Software version: 16.23.06.10_ 16.32.00.23U
FW-Rev: 1600.2200.10801.166
What I did so far:
downloaded IMG_Omega_HTC_Europe_2.05.401.01_Radio_Signed_16.23.06.10_16.32.00.23_OMEGA_RELEASE.nbh
renamed it to OMEGIMG.nbh
put it on microSD-Card
used goldcard-tool and made Goldcard of microSD card
put goldcard on one end of Y-Cable, Radar on thick end, and red end in USB port of PC, which put Radar to light
entered USB Host Mode by pressing vol down + camera (now it shows "Update in Progress" and reboots about 10 times every 10 (?) seconds...then this appears:
OMEGIMG.nbh - FAIL
RADIO - Fail
BOOTLOADER -
RCUST -
OS -
>*>*>*>*>*
Update Terminate
UPDATE FAIL
Error code: 33
I tried it a dozen of times and only once it showed me "Update Complete - Update Success". The next time I rebooted the device it showed an "SPL 2.5 MFG" but only once. After another reboot it was back to 1.8 again
But I think the Radio version was upgraded by this "success", since it was 16.23.02.09_2_ 16.24.00.23U when I bought this smartphone.
However, I am lost at this point. In the DFT-manual linked above the basic stuff to know doesn't contain "RUU". I downloaded the ROMUpdateUtility from the manual but when I try, there's always this Error 294- invalid vender ID.
I tried several times to upgrade spl_2.6.160015.3_WWE.exe, but it'S stuck at 0% and then I get the connection Error 262.
Also I might add, that the Radar isn't anymore in the Control Panel but only the HTC USB Sync-Driver (?)
I am afraid to update via Zune, because I read, if the SPL is too high, I couldn't downgrade again to HSPL. However, I never installed Zune. Is this still available? What should I do?
Edit: it worked
after GOldcard, the device restartet b itself and I missed that to enter SPL mode (instead it rebooted to USB HOst Mode by itself and startet the goldcard-method from beginning). By entering SPL mode I stopped the loop of goldcarding and after my SPL was 2.5 after first goldcarding, I was able to HSPL'ing the device

SGE2010 said:
Hi xda-community,
I am new to the Smartphone- and the Windows Phone world. My main cause is to get rid of the swisscom branding of my HTC Radar. But I also would really like to test some custom ROMs - especially the Dynamics HD2O looks promising in my mind. That's why I bought all the equipment necessary for Goldcard method for 2nd Gen WP7 phones as in this manual.
My Info:
HTC Radar C110e
Model ID: PI06100
SPL – 1.8. 160015.3 (131745)
Radio-16.23.06.10
Radio Software version: 16.23.06.10_ 16.32.00.23U
FW-Rev: 1600.2200.10801.166
Edit: it worked
after GOldcard, the device restartet b itself and I missed that to enter SPL mode (instead it rebooted to USB HOst Mode by itself and startet the goldcard-method from beginning). By entering SPL mode I stopped the loop of goldcarding and after my SPL was 2.5 after first goldcarding, I was able to HSPL'ing the device
Click to expand...
Click to collapse
Hi,
I use this ROM and it is very good one. But if you put HSPL already now you should put new radio RUU_Radar_Radio_17.5006.08.27 otherwise it will not work. Read the instructions in the tread. http://forum.xda-developers.com/showthread.php?t=1685271 in the tread there is link for downloading this radio. For me it was easy to HSPL the phone because I am not receive Country error and I don't need to use gold card just RUU.

Related

Cingular 8524, upgrade to 3.12.3.7, in Vista, getting 294 error

Alright so I am so frustrated with this...and I am sure there is a simple solution for it. The screen on my old 8525 got messed up and since it was under waranty they sent me a replacement...the screen is ok on the replacement, but the phone isn't working (shows exclamation point next to "wine glass" rather than signal strength bars).... after hours and several phone calls to tech support, High End Devices waranty dept and who knows where else, it was determined that the current ROM version is incompatible with the AT&T network, I have to upgrade. So the version of the ROM on the replacement is 2.15.502.3 which makes wonder why in the world would AT&T send me a phone that would not work on their network? (I'm really trying not to vent here...) Anyways so I go to the HTC website as directed by the Tech. Support person download the stuff and after another hour on the phone with HTC and every possible sollution that they know is tried still can't install. I am running a Vista 64 machine and after getting around all the Vista quirks I am finally able to get to the Bootloader screen (button combination is: Side button [Ok] + [Power] Then push [Reset]...if done correctly your phone goes to the 4 bar boot loader screen, if not your phone soft resets and you have to try it again...) anyways in the bootloader screen it goes to the installation bar on both phone and PC and goes to 1%, then durring that one percent I get the horrible "ERROR 294 : INVALID VENDOR ID" on the PC and the Phone resets.....No matter how we have tried it it is always the same thing...redownloaded the file 3 times, restarted the phone about a gazillion times and the PC about 2 or 3 times. What can I do? I would love to have Ms Windows Mobile 6, but all I really want is a working phone....can anyone please help?
Some more info for those of you that can help:
On "Device Information" screen here is what I have:
ROM version: 2.15.502.3
ROM Date: 04/09/07
Radio version: {blank}
Protocol version: {blank}
On Bootloader screen:
In the top (red) section:
(in white)
HERM100
IPL-1.03
(in yellow)
HERM100
SPL-1.11
and then at the bottom (white) section:
(in black)
USB
(it says Serial when I unplug the USB cable)
I am trying to install the ROM titled:
RUU_Hermes_CINGULAR_WWE_3.62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship.exe
downloaded from:
http://216.139.227.230/download/Sof...502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship.exe
found by going to http://www.htc.com, Support, AT&T 8525, Software Download.
Thank you for any help you can give.
u cant be serious......you got an invalid model ID from an 8525 while trying to install an update from at&t itself.
well the solution would simply be to install hardspl (see the sticky) and then install the update. although there are many other easier and faster solutions i think this is the *safest* way. but then the fact that your radio version shows nothing makes me wonder......maybe a corrupted radio or something, which may or may not be related to the invalid model ID error.......anywho, search the forums for error 294 its probably been discussed many times
First of all thanks for your help. So I tried installing the 2.10 - Hard-SPL-V7 and it wont finish the install. I connect the device follow through the installation and when I get to the point where I push Yes on the 8525 the screen goes to the red/green/blue/white bars screen shows
HERM100
IPL-SSPL by Des
HERM100
SPL-1.09.ds
then the Computer shows ERROR [260]: UPDATE ERROR and the installation stops....
error 260 is an open port error, reboot your computer, and try again, if it doesnt work, try a different usb port, also disable watever firewalls or antivirus software you have
Okay so I diabled both the firewall (Windows Firewall) and the antivirus (AVG) and restarted the computer...tried 3 different USB ports...still the same problem....You don't think it could have anything to do with Windows Vista 64 and Windows Mobile Device Center. BEcause as soon as I go into the new Bootloader screen, the WMDC shows that the 8525 is diconnected now...even though it's not. I saw a post on here about installing drivers to get Active Sync on a Vista machine, but the drivers it provides are unsigned and Vista won't let me load them....so what's the next step? And again thank you so much for your help.
Is there any use in putting more effort into this or should I just have AT&T send me a new one?
whether there's any use left is ur decision, dont ask me to help you make your decision.
i know you can install unsigned drivers on vista, i dont know how, use the search. i have also heard that updating wmdc to the latest version helps too.
or you can either try and install hardspl using the microsd card, again use the search.

[Q] Unable to flash any ROM!

Hello,
I'm about six hours into the process of trying to revive a nonfunctional HD2 that I purchased. I'm going batty!
Here is my status:
1) have installed SPL-2.08.HSPL 8G XE (0x05, 0x40) Cotulla HSPL
2) Have downloaded a few different roms (Chucky, TMO official, Energy) but they either get stuck at 0% or 9% (the highest it's gotten)
I'm getting pretty good at pulling the battery - it's like a new skill I never hoped to have!
I'm getting pretty frustrated because I've read about a hundred different posts on this site and I see that people are getting around this, but I'm starting to wonder if my phone has an issue that I can't resolve?
The phone doesn't boot up at all - it just says "Upgrade ROM code error, Please try again". Prior to my goofing with it, it just got stuck at the "Stick Together" screen. (Unwittingly bought it that way)
If I use the HSPL3_PKG to install/remove HSPL, it only works (connects to the phone) about one out of ten times, and out of the ~ten times I have gotten it to work, it only completed twice with a "We Hacked It" screen. The rest of the time it errors out just as I think it's getting the job done.
If I boot to the bootloader screen, I can put the USB cable in and see it change from Serial to USB (I've tried the thick and thin cables as some have suggested and haven't noticd a difference yet)
Then I kick of a rom update using the update utility that comes packed with it, and either the update process stops at 0% or it has made it all the way to 9%.
I'm in a position to get a replacement from TMO via the person who bought it (two for one, wife didn't like it, I bought it off of him) but I would rather not.
Any suggestions?
The part number of the phone is 99HKY001-00 B
jimmyswinger said:
Hello,
I'm about six hours into the process of trying to revive a nonfunctional HD2 that I purchased. I'm going batty!
Here is my status:
1) have installed SPL-2.08.HSPL 8G XE (0x05, 0x40) Cotulla HSPL
2) Have downloaded a few different roms (Chucky, TMO official, Energy) but they either get stuck at 0% or 9% (the highest it's gotten)
I'm getting pretty good at pulling the battery - it's like a new skill I never hoped to have!
I'm getting pretty frustrated because I've read about a hundred different posts on this site and I see that people are getting around this, but I'm starting to wonder if my phone has an issue that I can't resolve?
The phone doesn't boot up at all - it just says "Upgrade ROM code error, Please try again". Prior to my goofing with it, it just got stuck at the "Stick Together" screen. (Unwittingly bought it that way)
If I use the HSPL3_PKG to install/remove HSPL, it only works (connects to the phone) about one out of ten times, and out of the ~ten times I have gotten it to work, it only completed twice with a "We Hacked It" screen. The rest of the time it errors out just as I think it's getting the job done.
If I boot to the bootloader screen, I can put the USB cable in and see it change from Serial to USB (I've tried the thick and thin cables as some have suggested and haven't noticd a difference yet)
Then I kick of a rom update using the update utility that comes packed with it, and either the update process stops at 0% or it has made it all the way to 9%.
I'm in a position to get a replacement from TMO via the person who bought it (two for one, wife didn't like it, I bought it off of him) but I would rather not.
Any suggestions?
The part number of the phone is 99HKY001-00 B
Click to expand...
Click to collapse
After HSPL Install RADIO 2.14.50_04 then TRY to install latest Energy ROM.. Should work.
netvpn7 said:
After HSPL Install RADIO 2.14.50_04 then TRY to install latest Energy ROM.. Should work.
Click to expand...
Click to collapse
Even if it us a TMOUS HD2? I will give it a try, but I want to be sure before doing it!
Thanks for the reply
netvpn7 said:
After HSPL Install RADIO 2.14.50_04 then TRY to install latest Energy ROM.. Should work.
Click to expand...
Click to collapse
Once you have Hard-SPL on the device you don't need to worry about that anymore. Flashing Roms and radios will not overwrite it, that's what makes it "Hard". To make sure it's on there go into bootloader and it should show 2.08.hspl.
As for the radio, for TMOUS, just make sure it's a x.xx.50.xx radio (not a .51) and you'll be fine. If you have radio 2.10.50.xx you shouldn't have to change it.
So now I would try downloading one of the stock shipped Tmo ROMs (2.13 or 2.14). Then remove Sim and SD and go into bootloader, connect USB to PC and make sure it says USB on the device (not serial) and run the ROM Update Utility (RUU.exe). See if that works.
i also got this problem ,will try ur method n c
after hspl ,cant flash finish radio 2.14 it says ERROR (290) INVALID COMMAND.
excelpass said:
after hspl ,cant flash finish radio 2.14 it says ERROR (290) INVALID COMMAND.
Click to expand...
Click to collapse
You need HSPL..
HSPL done ,i tried a lot of files only Miri & Dinik n Duttys Leo Sense file can b flash successfully ,it went into menu once but now hang at htc startup again,,is this hardware problem?
i had the same problem last week. Drove me nuts.
i found there are more than one version of HPSL 3.
you have to download the latest one. for more info,
read my posts at
http://forum.xda-developers.com/showthread.php?t=789506&page=18
So you need HardSPL3 (the version is DarkForces Team HardSPL3 by bepe and Cotulla 21.06.2010)
If it still doesnt work, take a photo and post your screen
Still no go...
I have installed SPL-2.08.HSPL 8G XE (0x05, 0x40) Cotulla HSPL, the latest version I could find.
I just tried to flash RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship and it consistently flakes out at 8%.
I charged the phone all night, booted to the tricolor screen, kicked off the update as an administrator in Win7, the phone got to 8% and then the update flaked out on the PC - "The ROM update encountered communication errors during the update process" (Error [276])
I genuinely think that this phone is bunk - I'm just going to have the fellow I bought it from call in for a warranty replacement.
Thanks for your help, everyone...
SD card flash...
Hi,
I could not see it anywhere in this thread, and also I'm not certain if it is possible on a HD2. But on my xperia I'm usualy flashing from a SD card, copy the image over rename it as KOVSIMG.NBH (guess it would be something like LEOROM.NBH).
Than by pressing (and holding) volume down + power button while the device is off going to the boatloader screen which detects the card (must be inserted and flash from it IF there is the correct file loaded on the card.
Dude,
Did you actually download the HardSPL3 version from DarkForces Team?
If not, dont second guess anything. And if it works, you'll get your phone back.
The file name to download is "HSPL3_PKG.exe". Its by bepe and Cotulla 21.06.2010
If you downloaded the right version. it will support ALL LEO types, and all the SPL versions below:
SPL 1.42.0000
SPL 1.62.0000
SPL 1.66.0000
SPL 2.07.0000
SPL 2.08.0000
SPL 2.10.0000
you just select which SPL version to install in the Choose SPL screen. This version also disables the CID Check.
Dont knock it before you try it ..
+1
jimmyswinger said:
I have installed SPL-2.08.HSPL 8G XE (0x05, 0x40) Cotulla HSPL, the latest version I could find.
I just tried to flash RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship and it consistently flakes out at 8%.
I charged the phone all night, booted to the tricolor screen, kicked off the update as an administrator in Win7, the phone got to 8% and then the update flaked out on the PC - "The ROM update encountered communication errors during the update process" (Error [276])
I genuinely think that this phone is bunk - I'm just going to have the fellow I bought it from call in for a warranty replacement.
Thanks for your help, everyone...
Click to expand...
Click to collapse
Exactly in the same situation and dont know what to do...
snooffy said:
Hi,
I could not see it anywhere in this thread, and also I'm not certain if it is possible on a HD2. But on my xperia I'm usualy flashing from a SD card, copy the image over rename it as KOVSIMG.NBH (guess it would be something like LEOROM.NBH).
Than by pressing (and holding) volume down + power button while the device is off going to the boatloader screen which detects the card (must be inserted and flash from it IF there is the correct file loaded on the card.
Click to expand...
Click to collapse
Yes you are correct you can flash via SD card. You need a 4GB or lower SD card. This is not to say other higher GB SD card will not work, it is just that it has been stated many times the higher SD cards sometimes work to flash a ROM and sometimes don't. The card needs to be formatted with Fat 32. You have to find the RUU_(wharever).nbh and rename it to leoimg.nbh ( you almost got it righ tsnoffy lol) and copy it to your SD card. insert SD card into phone and hold the volume down botton down anx tap the power button keep holding the volume down button down until you see bootloader come up and say searching then let go of the volume down button. The ROM will flash.

[Q] Have I killed my HD2?

Apologies for the new thread.
I bought a HD2 off ebay a few months ago and have a had numerious problems using it as a phone, goes from 4 bars to none every couple of mins cuts off mid call, basically doesnt work inside the house. I called HTC support & they took the serial number then told me it was a "demo" phone and unsupported, I went to the website to see if I could download a ROM update but my serial number was not accepted trying to download any of the roms.
It was running 1.66.405.2 ROM
So, using a serial number off here I downloaded the 3 roms off the HTC website and tried to install them everytime getting the "Invalid Vendor ID" error. I then installed HSPL3 then tried to install one of the 3.14 ROMS using the SD card route, it got to about 2% then rebooted with the error "Software update failed, please try again" and when i go to Bootloader it shows "SPL-3.03.0000"
Anyting I can try to get this back up? even if its just to give to the kids for playing music / videos!
Is it worth going down the goldcard route?
Regards
Paul
its just possible that you may be stuck, with goldcard the only option.
You made two mistakes.
firstly, using hspl to run a 3.14 rom leads to instability and memory problems. You cant do it that way with 3.14.
secondly, flashing the 3.14 rom from sd card was a double bad move, because 1 - its not for your device, and 2 - the fact that hspl is there lets it skip the warning initially and update the spl to 3.03.0000, which wouldn't have happened if hspl wasn't there.
You now need to find the correct stock rom for your device to downgrade spl 3.03.0000. Normally i would say find a 1.42 or 1.66 rom, (for the correct carrier if rom locked, or for HTC if not)
You didnt say which 3.14 rom you used (noob omission, lose a point ) se we cant yet rule an area out. for example, if it was the wwe htc 3.14, then we know the phone is branded (pretty likely if its a demo)
ALternative to trying every 1.66 rom you can find, is goldcard. That will allow the 3.14 rom of your choice (or indeed any stock rom) to flash no problems, hspl not required.
Yeah you learn by your mistakes!
Think I eventually got sick of the thing cutting off it was about as much use as a brick as it was! & HTC support were about as much help as hammer! Told me it was an old model & I should consider upgrading!
I've tried 1.43, 1.48, 1.66 all off the HTC website, went through all the other carriers as well entering my serial number in with no luck. The ROM i used was
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship this is what was on it before I ran the update.
Os Version - 5.2.21869 (21869.5.0.81)
Manila Version - 2.5.19211619.0
ROM V - 1.66.405.2
Rom Date - 1.11.10
Radio Version - 2.07.51.22.2
Is there anyway to find out who the carrier would be from the serial no?
only by trying to download every rom for every carrier for every region, and theyre not all on teh website,,,,
goldcard would be your best bet.
Is there any way to create a goldcard when you can only get access to the bootloader on the HD2?
The steps outilined in http://forum.xda-developers.com/showthread.php?t=642486
3:Get the SD card's Serial number & Make the Gold Card
--a: Unplug your HD from the PC and Plug it back in select ACTIVESYNC on your LEO
--b: Run PSAS, Calculators/Generators > Generate HTC GoldCard >
--c: Select LEO from the Drop-down box
--dress "Get SD Card Serial from WINCE Device"
--eSAS should see all the drives on your HTC Leo/HD2. Make certain the correct size disk is sellected. For example, I inserted a 512MB SD card so - Beneath the (CID) box you should see something like " Disk Nr.: 04 - Disksize 512 MB"
--f: Now that the correct disk is selected, press "Save Goldcard Image to WINCE SD"
--e: you should see "Done writing SD Card to WINCE Device.
I get the error message "could not open connection, device connected?"
When I turn on the phone all I get is the bootloader menu page!
Resolved
Ok its now sorted,
I bought PSAS and made a goldcard using my old HTC touch. I then installed the 1.66 rom before updating to 3.14
I still have the same phone reception problem, would it be worth trying a different radio to see if that would fix the reception problems?
Thanks for all the help and advice.
Paul
you can't change the radio when running 3.x, because there is no hspl to allow it, sspl can't flash radios and goldcard is for stock roms.
So I'd need to goldcard it back to 1.66 or such then try a few radio roms to see if it will fix the reception problems? Whats the chances a new radio would resolve it?

[Solved] Half Bricked Titan I (AT&T)

Ok, half bricked it while trying to update SPL to 2.05 with goldcard...
I understand that a half brick is when you hold both volume buttons down on boot and neither serial nor usb show up in the spl screen. Between this and my inability to flash the SPL 2.05 (gets stuck at "Loading..." and takes several minutes to even get past "Load USB Host". I've left it at "Loading..." for an hour, no progess...)... I'm stuck and need help.
When I hold the volume down button at boot and connect to Zune, I get this error: c101002e
I've read that this can be solved with the windows phone support tools... but MS's page also says not to use this on versions higher than 7.0.7something. Unfortunately I forced the update to 8107, so I don't want to find out what happens when you ignore the warning.
Basically everything is stock ATT except the forced update;
Radio:16.23.02.26_A_16.27.00.23U
SPL 1.10
Is there anything I can do to fix this? Please help
Update 1;
Tried to flash the SPL2.6 update from HTC using goldcard, no dice, gets stuck at "Loading..."
Tried to flash the Eternity cingular stock rom, once again, stuck at "Loading..."
I think I'm beginning to see a pattern; USB host works as far as reading the SD card, but beyond that it fails...
Update 2;
I wonder if I can reapply the firmware through cab sender? I would need firmware cabs for the htc titan, preferably ones that are compatible with the new hspl! I can't find any, been searching for hours...
Was the HSPL process successfully completed? Have you tried to put the phone back into USB com mode (camera + vol down + power) and putting the OSPL back on?
You're the first I've heard having this problem. Since you're using the Gold Card Method, I assume that your phone is a US AT&T Titan.
I hope you get it going.
---------- Post added at 04:13 PM ---------- Previous post was at 04:07 PM ----------
Not sure if you visited this page or not, but here are the instructions for flashing the HSPL. Further down the 1st post you'll find how to un-install it. I would try that since it doesn't sound as if your flash was successful.
Here is the link to the actual gold card method, if you haven't seen that as well.
No, didn't even get to HSPL. The instructions say to flash SPL 2.05 first, which isn't working. I'm stuck on the stock 1.10 SPL.
No matter what I try, any combination of flashing the original stock ROM, the HTC SPL update, etc, goldcard always gets stuck at "Loading..." so I think it's safe to say goldcard is broken as well, unless someone knows a foolproof fix.
Camera + Volume Down + Power... I assume you mean USB Host mode which is just Camera + Volume Down at bootup (holding the power button causes the phone to reboot). USB Host mode is how you use gold card, and like I said, it gets stuck at "Loading...". It does in fact read my SD cards because I saw the blinking LED that signals activity on one of the USB to microSD readers I tried.
Moreover there is nothing to uninstall since I am unable to install anything. I can use the WP7 cab sender, if I could just get the bootloader in cab form I think this would solve my problems; I think the stock SPL became corrupted somehow and needs to be reflashed... and I do not know anything about JTAG
When you made your Gold Card, did it say success or give you a problem?
Are you using a multi card reader or a single card reader for your gold card?
it says success.
I've tried two microSD cards, and three different card readers. I have gotten the CID for each card and properly applied the CID to each card, and properly formatted each in fat32 several times...
I've tried using the HD2 in Magldr usb mass storage mode, HD2 in android mass storage mode, HD2 in windows mobile mass storage mode... they all appear to work as it gets as far as "Loading..."
Moreover I have a single card reader and a multi card reader.. each making no difference; stuck at "Loading..."
I have tried a hundred different combinations which all appear to be successful if not for the fact that I'm pretty sure my SPL is corrupted.
Wow, that really sucks! Sorry I can't help. I haven't even done it myself yet. My y-cable will be here hopefully Friday.
The only other thing I would make sure of if I were in your situation is looking at the pics in gold card method post, I see that the gold card is to be placed in the female end at the bottom of the Y. You never said whether you made your own cables or not, but if you did, maybe make certain that it is correctly done.
Damn, while I'm sorry for your situation, I sure hope that I'm not right there with ya when I attempt it. Keep us up-to-date and good luck.
Yeah I bought a new Titan off ebay already XD
However before I open it I'm going to see if I can convince HTC that it was pre existing (it probably was) and that I found out while I was trying to do the official SPL update from HTC using the tool on HTC's site (which is more or less true as well XD). I think I'm still under warranty.
And I was using this Y cable http://www.amazon.com/gp/product/B000JIOHDE/ref=oh_details_o03_s00_i01
It works, I've tried it in various setups. It's actually really nice; the grey cable doesn't carry data so you can use your computer or laptop for power without worry. But I did in fact use a wall USB charger for goldcard, just in case.
But don't worry, I'm almost sure that this was pre existing; gold card/USB host mode behaved exactly the same from the start, the only thing that has changed is the fact that I can't get Serial / USB connections to show up in SPL anymore (nor can I hard reset from SPL). It worked correctly at least twice...
hey everyone, I fixed it.
USB host mode / gold card works; if you're stuck at "Loading" then your SD card is no good. I went around and tried every mass storage device in my house and found one that works, use the generic goldcard image from here http://forum.xda-developers.com/showthread.php?p=24809318#post24809318
To get rid of f400 error you need to flash cotulla's ROM, the cingular stock rom did not fix it.
Goldcard SPL up to 2.05, USB worked.
Install HSPL via USB, if that doesn't work, install the stock ROM via USB and start over.
Once HSPL'd at 2.05 USB will NOT work, so you'll need to goldcard cotulla's ROM (remember to rename it from FINAL.nbh to ETERIMG.nbh)
profit.
link68759 said:
hey everyone, I fixed it.
USB host mode / gold card works; if you're stuck at "Loading" then your SD card is no good. I went around and tried every mass storage device in my house and found one that works, use the generic goldcard image from here http://forum.xda-developers.com/showthread.php?p=24809318#post24809318
To get rid of f400 error you need to flash cotulla's ROM, the cingular stock rom did not fix it.
Goldcard SPL up to 2.05, USB worked.
Install HSPL via USB, if that doesn't work, install the stock ROM via USB and start over.
Once HSPL'd at 2.05 USB will NOT work, so you'll need to goldcard cotulla's ROM (remember to rename it from FINAL.nbh to ETERIMG.nbh)
profit.
Click to expand...
Click to collapse
Hi, I'm stuck with f400, running official eu rom with spl 2.5 . no HSPL , no downgrade , no nothing...
Which cotulla's rom are you reffering to?
Please help. (ATT HTC Titan)
spyros_tazz said:
Hi, I'm stuck with f400, running official eu rom with spl 2.5 . no HSPL , no downgrade , no nothing...
Which cotulla's rom are you reffering to?
Please help. (ATT HTC Titan)
Click to expand...
Click to collapse
It's been months since anybody has posted on this thread. There are two ROMs that set this process up. Depending on whether you have the x310a (American brand) or x310e (European). When this process is all said and done it reads x310e regardless where it came from. There is a Cingular 1.09 and an European 1.10...the key here is to downgrade the SPL from 2.05 to 1.09/1.10. Some Titans have lower SPLs depending where you're at. HTC's SPL update to 2.6 complicates this process. Think of as 3 major steps...one, downgrade to one of these ROMs, two, return to SPL205 via Goldcard and then apply DFT's HSPL. Step 2 took me forever to get right and the process is sneaky long...you think you failed but patience will be rewarded. There has been quite a lot of discussion in regards to "newer" Titan (Eternity) which the internal drive is set up in such a way that one is lead to believe it is corrupted or they've been setup like the Titan II (Radiant) which to date remains impossible to HSPL. You're better off using one of the older Titans (Eternity). A few of the links no longer get you the files you need and if they do I would encourage you to download everything that is there and read every tutorial carefully and then again; this isn't for the faint of heart. It's way, way harder than the HD2 or older HTC devices. Nor am I aware any device since the Eternities is HSPL capable other than maybe the Nokia Lumia 920 Developer Edition.
berrywr said:
It's been months since anybody has posted on this thread. There are two ROMs that set this process up. Depending on whether you have the x310a (American brand) or x310e (European). When this process is all said and done it reads x310e regardless where it came from. There is a Cingular 1.09 and an European 1.10...the key here is to downgrade the SPL from 2.05 to 1.09/1.10. Some Titans have lower SPLs depending where you're at. HTC's SPL update to 2.6 complicates this process. Think of as 3 major steps...one, downgrade to one of these ROMs, two, return to SPL205 via Goldcard and then apply DFT's HSPL. Step 2 took me forever to get right and the process is sneaky long...you think you failed but patience will be rewarded. There has been quite a lot of discussion in regards to "newer" Titan (Eternity) which the internal drive is set up in such a way that one is lead to believe it is corrupted or they've been setup like the Titan II (Radiant) which to date remains impossible to HSPL. You're better off using one of the older Titans (Eternity). A few of the links no longer get you the files you need and if they do I would encourage you to download everything that is there and read every tutorial carefully and then again; this isn't for the faint of heart. It's way, way harder than the HD2 or older HTC devices. Nor am I aware any device since the Eternities is HSPL capable other than maybe the Nokia Lumia 920 Developer Edition.
Click to expand...
Click to collapse
i managed to downgrade to official att rom,and got rid of f400 error, but the spl didn't downgrade...
I installed the rom 3 times with no luck with the spl...
Afterwards i renamed the eu rom from ETERNIMG to ETERDIAG and it installed.
but still the spl is :
PI39100 MFG
SPL-2.5.160015.3(137079)
eMMC SND 15188MB
TOUCH A1(F:81, ID:1,V11,B:F8)
Radio-16.23.02.09_A
I tried to install spl2.05 again (I don't remember but I think it failed), then spl2.6 with no luck, then hspl without results...
Finally I upgraded to 7.8 via cab installer and thats the best I managed to accomplish...
So I can't install any spl or hspl...
when I bought the device ,it had spl 1.09, not 2.6, so I think it's possible to hspl...

[Q] HTC Radar HSPL2.5 F400 error

Please Help ! I read lots of pages in forum, but can't find what I'm doing wrong. I want to get HSPL working to able to instal custom ROM to use Nokia apps, witch are way better than HTC and Marketplace apps.
Phone, HTC Radar 4G T-Mobile US
Windows Phone 7.8 (pushed on update with seveneight tool)
OS Version 7.10.8858.136
Firmware vers. 1600.2200.20402.531
Hardware revision: 0002
Radio vers. 16.23.05.13_16.30.00.23U
Radio hardware vers. 2.16.0.D4
Bootloader vers. 2.5.160015.3(137079)
Here is what I did, I flashed using Goldcardtool with Y-cable, OMEGIMG.nbh. I think flash did not finished properly, it went too fast, phone rebooted to SPL , plugged in to PC used DFT_HSPL_WP7SG1_INSTALL, install finished OK , but when I boot up to HSPL mode it does NOT connect to PC.
(Using ROMUpdateUtility getting connection error (260))
Here is how my screen looks in HSPL mode;
PI06110
HSPL2.5 1600.3(137079)
eMMC SMS 7376,FA31
CotullaH(F:80,ID:10,V20,B:AA)
Radio-16.23.05.13_2
F400
Please Help, what I'm doing wrong ? Why my HSPL have F400 error ?
Thank You so much !
Problem fixed. After HSPL install needed second time boot to USB Host mode and this time radio installed correctly. All good now, time for custom ROM
newappz said:
Problem fixed. After HSPL install needed second time boot to USB Host mode and this time radio installed correctly. All good now, time for custom ROM
Click to expand...
Click to collapse
Flash the radio also.

Categories

Resources