Related
Ok.
So at some point I soft bricked my phone and I got the Phone -- ! -- Computer screen.
Managed to get it back into download mode, and then unbricked it by getting it flashed to EB01 as instructed in this thread
http://forum.xda-developers.com/showthread.php?t=1026746
So now I have EB01, which is working, however there is a new problem.
When I try to plug the phone into a computer, it is not recognized (Says the device has malfunctioned).
I have tried 3 different computers. I made sure I used the cable that came with the phone.
I brought it into the Verizon store, and they were unable to get any of their computers to recognize the phone either (we tried a few other cables there as well)
This is both in download mode and within the OS itself.
They told me to try downloading Vcast however that didn't work either.
So now I'm wondering if there is something I can do to get it to recognize it properly again.
Has anyone run into this situation before and managed to fix it?
I did twice have the phone plugged in via usb to my car, and walked out the car (was talking on the phone), and the USB yanked out, so that could have potentially damaged it (though it still charges, so I don't know)
Yanking it out could have very well done it. Only thing I would suggest is reformatting the drivers and attempting again this time leaving it plugged in and rebooting the computer. If that doesn't work, replacement time.
Do you have "usb debugging" turned on?
Did you activate the connection from the phone after connecting to computer? (mine shows a green screen with a button to activate the connection for mass storage)
beyond that... idk.
redownload the samsung drivers
based on the fact that so many PC's have been unable to connect and the info on yanking the USB charger in the car (I think we have all likely done that - though for me it has happened at work with the laptop<->network cable...) you may have damaged the plug/receptor (not sure what would be proper...).
I would do a visual inspection for kicks, though I am sure there could be damage you cannot see.
I believe that these USB connections are a minimum of 4 conductors (some devices are more proprietary and use more pins to ensure you are using an official cable so they can get you to buy more of their stuff - though some of those pins are not actually wired through the cable, but rather short to each other...). If you damaged only one, that could likely be the reason that you can get a charge but no data comm - and since it seems likely that one of the two data pins would be tx and the other rx, then I could see why teh PC would report the device had malfunctioned...
I am guessing here - logic, please don't fail me...
Hey guys, thanks for dropping by.
I have a very wierd problem, that I just cant figure out.
It all started the other day, when I found my tablet dead after having been left on and charging during the night. The tab was dead, and I feared the worst. After having left it on what seems to me like a trickle charge for several hours, I managed to get it up and running, and the tab seems fine, it was just completely out of juice.
But my troubles are not over. Whenever I'd connect the tab to the wall charger, I'd only get the red "X" symbol in the corner, and it would say MTP Initialize, even though its plugged into the standard OEM wall charger that comes with.
When I connect the tablet to my computer using the same cable, nothing happens, and by that I mean nothing. Computer doesn't start the connection process at all, its not recognized in the device manager, nothing. Not even Odin can see the tablet when I put it in download mode, the tab keeps saying "Waitting USB Cable..."
Tried this on 2 computers, still no luck, even using a USB plug on the motherboard instead of front-usb.
Now, the tablet will "trickle charge" from both the wall charger, and the computer, but nothing else happens.
I figured it could've been the ROM, so I got the latest ICS Kanang ROM downloaded, transferred it to my tab using Bluetooth, and flashed this without hassle, but the problem still persists, only now showing a regular charge icon in the lower right section, but it is still only trickle charging as far as I can tell.
All I can figure is a defective USB cable, or even worse, defective port on the tablet itself, but I'm not sure. I've ordered a new cable from DealExtreme, that will hopefully arrive sooner rather than later.
But seeing as the tab is hardly 4-5 weeks old, I find it difficult to believe the cable is the problem.
Anyone have any ideas? I'm all out at this point, so any pointers is very appreciated. Thanks.
It could be the cable. It's the part you have used in each situation. I'd wait for the cable to arrive and test it with the tablet when you get it.
Sent from my GT-P7510 using xda premium
Hey, thanks for the reply.
Yeah, I really really hope this is the case, time will tell, DealExtreme is not the quickest dealer. I'll update when I get it.
The new cable came from DX, but I'm afraid it showed no difference on anything.
The cable is working just as the original one, so that's not the problem.
Anyone have any ideas?
I guess my main goal at the moment is flashing it back to stock and un-rooting so I can get it repaired.
You mind posting a screenshot, it's kinda hard to imagine what you see by what you read For all I know my imagination went from a red X to the corner to something like an X off battousai's face.
Then again, I'd be glad to help, provided you post screenies, would be a major help
Ah, yes, I will take screenshots of anything you want to see.
Right now im on ICS preview, and these are some snapshots WITH the cable connected.
The red "X" I'm talking about you can see on the first picture on the charging icon, this happened even when the wall charger was connected on gingerbread/overcome experience rom.
The other pictures you can see it says discharging. Now, this was taken when connected to the computer, and I guess that's normal, but it also happens exactly the same when connected to the wall charger that came with the unit.
If you want screenshots of anything else, ill get it asap!
I took a poorly image of the tab connected via USB, to my computer with Odin open, hopefully you can see what it says.
If not its just what happens, I don't get further.
By the screenshots, Is the language Swedish?
Then again thanks for providing the screenies
In your first screenshot that could be part of the theme, or was it never there previously? I don't really know if it's not charging or that's supposed to be the charging icon, because for some odd reason on ICS preview I don't see that red icon anywhere.
As for the tablet, the reason why you aren't detecting it seems as though you don't have the drivers on the PC, I don't know if you installed them or you didn't mention it because I never found it being mentioned in your reply. I know it sounds silly but the same thing happened to me when I was using the tablet, (originally my 3G series belonged to my dad who knew nothing about modding so he just gave it to me and said, "do your thing" ) He did also forget to mention that you require to have the drivers to detect it via Device Manager and MTP in general, shortly the COM port will show up aswell. Perhaps re-installing the drivers should do the trick?
Made me wonder how did you install ICS in the first place if you weren't able to have it read? But I realized you could have downloaded the zip file via the tablet, On another note, how did you install CWM in the first place? o.o
Hehe, almost! Its in Norwegian on the honeycomb picture.
The red "X" would show up whenever i was connected to the PC via USB, to indicate its not charging. It will however "trickle" charge, and take 24h to charge fully with no usage and turned off.
Yes, the red icon is not on ICS, it just says not charging in the about page, as you can see from the screenshot.
Drivers have been reinstalled two or three times on two different PC's, I don't believe this is the issue.
When I bought the unit, it was working 100%
USB was okay, I flashed and rooted the unit over to "Overcome Experience".
From there I transferred ICS preview via Bluetooth and installed that way.
Have you tried factory reset to make sure all modules are reset? Maybe the USB charge module in Overcome is conflicting.
Yes.
Factory reset 3-4 times on the two different roms. I've reset everything I could find, without success.
Perhaps it has gone faulty with the tablet's plug in port, someone had the same issue although it was his wire that was at fault, it detects the charge via USB but not enough volt's to be detected by the PC, has it been grounded? Seem's more likely :| Might have to get it checked in your local center perhaps, It's how I mentioned that any metallic object is able to relay electricity despite being broken or not, you may have a broken pin for all I know :|
Hi,
I'm having exactly the same issue with my 1 month old tab 7+. I tested it using my bosses charge cable and there is no issue so I need to go to the service centre for a warranty replacement on the cable.
Hope you sort out your issue soon!
Thanks, but I don't think I have any other choice to deliver it to Samsung Europe as a payable service to get it fixed.
Purchased on a American store, and I doubt they'll take it back with flashed software.
I'm not sure really, I'll see what I end up doing. Its not the cable, that's for sure.
My problem is that I cannot connect my Galaxy S II to computer. When I try to connect it only says "unknown device". I have tried with newest Kies and without Kies. With multiple computers with Vista and Windows 7 32bit. Also downloaded Samsung Galaxy S drivers manually from web but with no avail. And I have tried with Usb-debugging on and without it. I also tested USB-mass storage setting but it does nothing. Computer also says "unknown device" when I try to connect phone while in download mode.
The charging works btw.
When I connect the cable my phone just makes the normal sound but the mass storage android man newer appears to top tray. I have also made factory reset and cache delete from recovery but with no luck.
I would like to flash different rom with Odin but I cannot do that when the connection is not working. My current rom is official XXLPQ ics. The usb cable isn't the problem because I have tried with different cables which work normally with other phones.
Is the warranty repair only solution? Really wouldn't want to be without my Galaxy during the repair time.
Sounds like it's going to need a check over, if it wasn't for the fact you have tried multiple computers AND leads, as I had a similar problem but found it was down to my PC needing a fresh install.
Unless others with similar experiences have advice it doesn't sound good, as though pins 2, 3, or 4 have problems maybe, or that the board within the phone has bent up or down through rough handling/tug on the cable.
When did it start happening? I had a fright by tripping over the phone while plugged in, and ripped the plug out while launching the phone across the room. It broke the charger and thought I'd killed the port on the phone, but found if I propped the plug up and put weight on the phone it would connect, like this...
hxxp://i.imgur.com/y1bPj.jpg
Might work if the board has got a whack like mine did.
Sub Atomic Specialist said:
Sounds like it's going to need a check over, if it wasn't for the fact you have tried multiple computers AND leads, as I had a similar problem but found it was down to my PC needing a fresh install.
Unless others with similar experiences have advice it doesn't sound good, as though pins 2, 3, or 4 have problems maybe, or that the board within the phone has bent up or down through rough handling/tug on the cable.
When did it start happening? I had a fright by tripping over the phone while plugged in, and ripped the plug out while launching the phone across the room. It broke the charger and thought I'd killed the port on the phone, but found if I propped the plug up and put weight on the phone it would connect, like this...
hxxp://i.imgur.com/y1bPj.jpg
Might work if the board has got a whack like mine did.
Click to expand...
Click to collapse
I received it like this. Only 4 months old though. I tried to bent the cable plug slightly when connected to computer but it didn't help.
check wiv diff cable..
install phone drivers in kies...
check usb port on phone and pc ,if any debris then clean...
android on tray -drag down and c if u can connect as storage...
rocky23 said:
check wiv diff cable..
install phone drivers in kies...
check usb port on phone and pc ,if any debris then clean...
android on tray -drag down and c if u can connect as storage...
Click to expand...
Click to collapse
As I mentioned earlier I have tried all that.
My SGS2 keeps disconnecting and reconnecting the usb with my computer. This is hapenning for quite a long time now.
I keep hearing the windows connect/disconnect usb sound when my phone is plugged in, making it unable to recognize the device.
Today, it finally didn't had this problem for a while, so I took my chance to get back to stock ROM (because I need to send my phone to Samsung for camera problems). So I flashed stock ROM with ODIN, but I encoutered a problem: it didn't get further than the boot animation.
When I tried to reflash, ODIN didn't recognize my phone anymore, just like before. When I plug in my SGS2 to my computer while on download mode, it just keeps reconecting the USB, so the device can't be installed.
Tried a different computer. It kept being connected, but that comp sucks and it couldn't recognize my phone at all. My own computer also has problems recognizing the SGS2, but also has the problem that it can't stay connected.
Things to know:
- Other usb devices do stay connected, it's just for my sgs2
- I've tried different USB hubs etc., reinstalling Kies, uninstalling drivers.
- It does keep charging the phone, even when the computer makes the disconnect sound. That makes it even weirder!
Basically I'm seriously out of clues how to revive my phone
I don't want to send it to Samsung, scared of losing warranty.
You guys are my last hope!
to start the ball rolling, YOU SHOULDNT BE connecting sgs2 to a HUB, thats probably the fault, second, have you tried a different usb lead or a different computer with the same lead to either verify if its the phone or lead at fault??
No one on here can answer your question because it sounds like a hardware issue, wire or hub or charger port, but it is an elimination process and only you can do that.
If you try everything and still get no joy, restore your pc to an earlier point, uninstall the samsung drivers and re-install them etc etc.
I very much doubt its a software problem tho, looking at what you tried already, lots of people use hubs, if youre flashing roms and your connected to a hub then ya play a dangerous game and risk soft bricking your phone, most of the time odin wont recognise your phone through a hub, same if ya usb lead is too long, itll charge but no data. always connect it directly to the pc usb 2 port.
gazza35 said:
to start the ball rolling, YOU SHOULDNT BE connecting sgs2 to a HUB, thats probably the fault, second, have you tried a different usb lead or a different computer with the same lead to either verify if its the phone or lead at fault??
No one on here can answer your question because it sounds like a hardware issue, wire or hub or charger port, but it is an elimination process and only you can do that.
If you try everything and still get no joy, restore your pc to an earlier point, uninstall the samsung drivers and re-install them etc etc.
I very much doubt its a software problem tho, looking at what you tried already, lots of people use hubs, if youre flashing roms and your connected to a hub then ya play a dangerous game and risk soft bricking your phone, most of the time odin wont recognise your phone through a hub, same if ya usb lead is too long, itll charge but no data. always connect it directly to the pc usb 2 port.
Click to expand...
Click to collapse
Ow, I think I used the wrong word. I meant to say port instead of hub.. Translation fail there. So that's not the problem, I've put the cable directly into the USB port.
I think you are right about the hardware problem. I'm just not sure where the problem is. I only have one cable, so I can't test that atm. But like I said, the connection problem does NOT occur on another computer. It keeps the device connected (as an unknown device though).
So it's weird: it looks like a SGS2 hardware problem, but on the same time it has a different problem on a different computer. It's really confusing...
Thanks for the quick reply by the way
sebas156 said:
Ow, I think I used the wrong word. I meant to say port instead of hub.. Translation fail there. So that's not the problem, I've put the cable directly into the USB port.
I think you are right about the hardware problem. I'm just not sure where the problem is. I only have one cable, so I can't test that atm. But like I said, the connection problem does NOT occur on another computer. It keeps the device connected (as an unknown device though).
So it's weird: it looks like a SGS2 hardware problem, but on the same time it has a different problem on a different computer. It's really confusing...
Thanks for the quick reply by the way
Click to expand...
Click to collapse
Android Sync manager Wifi is the answer you're looking for ^^
no more plugging in this... mounting that...
NB, has a pc side component
King_Rat said:
Android Sync manager Wifi is the answer you're looking for ^^
no more plugging in this... mounting that...
NB, has a pc side component
Click to expand...
Click to collapse
Then please explain me how I could ever do that when there is no working ROM on my phone. I'm stuck on the 'restore with Kies' screen, like I told in my post (yes, still). And how it will ever work with ODIN? It won't...
Now not any computer is connecting with my sgs2. It just doesn't show anything (not even unknown device). I'm going to try to buy a new cable. Is it needed to buy a Samsung cable? Because it's harder to find than just a regular usb to micro usb cable (and more expensive ). This is my last hope. When it's not working, I need to send it to Samsung.
sebas156 said:
Then please explain me how I could ever do that when there is no working ROM on my phone. I'm stuck on the 'restore with Kies' screen, like I told in my post (yes, still). And how it will ever work with ODIN? It won't...
Now not any computer is connecting with my sgs2. It just doesn't show anything (not even unknown device). I'm going to try to buy a new cable. Is it needed to buy a Samsung cable? Because it's harder to find than just a regular usb to micro usb cable. This is my last hope. When it's not working, I need to send it to Samsung.
Click to expand...
Click to collapse
You need to replace your usb board within your phone. New part can be found on ebay for around $10. It's a really simple task replacing it. No soldering or anything.
It's been well documented on these boards.
Sent from my GT-I9100 using Tapatalk 2
Earlier today I wanted to move some files about on my phone in preparation for a wipe and reflash. I managed to copy off a backup I made. Suddenly, the USB disconnects. Thought the cable may have simply disconnected, I proceeded to unplug and replug my phone, but no dice. The phone seems to charge, but USB connection does not initiate.
I tried rebooting both machines and reinstall USB drivers, but still no connection.
I ended up giving up for a bit and played a game for a couple of hours. Weirdly, during this time my phone happily connected, providing the USB options in the notification area.
I ended up unplugging my phone again, but when I plugged it back in a few moments later, it did not connect. It's since been connected for around 15 minutes, with absolutely nothing but charging occuring from my phone.
Any help would be a appreciated.
Thanks!
Edit: I have also tried numerous cables.
I've also encountered this problem, look for something called 'MTP fix' and see if that works!
Sent from my GT-I9100 using xda premium
USB port/board on the fritz. Replace before it dies completely (you won't be able to charge/etc). You need to work out which revision of the board you currently have in the phone & buy the same board (cheap; eBay/etc) & swap them out.
Search for similar threads, there's been a lot of discussion here about this issue/which board you need how to replace over the past few mths (including photos).
Aw crap.
I'll try the MTP Fix suggested above, but if that doesn't work I'll look into this. How difficult is replacing the board?
For those interested, board replacement information can be found here: http://forum.xda-developers.com/showthread.php?t=2335961