Hi guys,
I am trying to root my S3, but after installing the drivers and whatnot, I open up Odin, select the pda then plug my phone in (in DL mode) and hit start. now odin can see the phone, and tells me its added, but it just sits on "setup connection" until it times out and says failed...
This is the directions im going off
any help would be gladly taken on board
This is the log from Odin
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9305_CWM_Recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
You are posting in I9300 Q&A, go here for I9305
besides this, make sure KIES is not running in the background, but I am not familiar with the I9305 itself.
That root is not for your phone if you took the time to read op
slaphead20 said:
That root is not for your phone if you took the time to read op
Click to expand...
Click to collapse
well his log shows: I9305_CWM_Recovery.tar.md5 is valid. not sure though, you are the specialist
its the same situation for anything i try to flash. even following the directions from This thread, in which my mate with the same phone has used.
chrismast said:
You are posting in I9300 Q&A, go here for I9305
Click to expand...
Click to collapse
as I said, maybe try you question in the correct Q&A forum, guess there are people that might be able to help you
can this be moved, or do i just start the thread again?
sorry for the wrong post location, being a similar phone its an easy mistake to make.
Related
Hi There,
After using temasek's stock android rom a while without any problem my galaxy s3 won't turn on anymore. About a month ago my S3 suddenly shutted down and now I get a bootloop where I only see the samsung logo reappearing every 5 seconds. I can't go into recovery mode, only into download mode. So my phone is soft bricked i supposed.
I tried almost everything, I searched for weeks for a sollution on XDA and I didn't found anything that could help me. So now i'm asking you guys because i'm a little bit desperate and i'm using my old nokia 3310 for a couple of weeks now.
I tried to reinstall my original firmware which I downloaded on sammobile with odin but there is always some kind of error.
I tried several versions of odin (new one's, olders one's) And still no progress.
Here's the log from odin v 1.85 :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9300_PHN_I9300XXALE8_I9300PHNALE4_I9300XXLE8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I just checked off the box "PDA" and "AUTO REBOOT" and "F. RESET TIME" . When I use a pit file this is the log of odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9300_PHN_I9300XXALE8_I9300PHNALE4_I9300XXLE8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
I'm sure that i used the right firmware, I've tried different pc's, i've also tried differend firmwares... Always a damn error in odin...
Can anyone help me?
ID:0/006> There is no PIT partition.
If you use a PIT file it has to be the right PIT file .
jje
JJEgan said:
ID:0/006> There is no PIT partition.
If you use a PIT file it has to be the right PIT file .
jje
Click to expand...
Click to collapse
I used the GT-I9300_mx_20120329.pit file which was suggested in this topic: http://forum.xda-developers.com/showthread.php?t=1894548&highlight=stock+firmwares
Weird. Sounds like SDS. What kernel were you using aling with Temasek s ROM?? And which version??
dhirend_6d said:
Weird. Sounds like SDS. What kernel were you using aling with Temasek s ROM?? And which version??
Click to expand...
Click to collapse
Version 77 and his kernel!
Hi All :fingers-crossed:
i have Galaxy SII GT-I9100G
i were flashing it with odin and had an error
<ID:0/035> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GXXLSR_I9100GXXLSP_I9100GXEFLSR_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/035> Odin v.3 engine (ID:35)..
<ID:0/035> File analysis..
<ID:0/035> SetupConnection..
<ID:0/035> Initialzation..
<ID:0/035> Get PIT for mapping..
<ID:0/035> Firmware update start..
<ID:0/035> cache.img
<ID:0/035> NAND Write Start!!
<ID:0/035> factoryfs.img
<ID:0/035> hidden.img
<ID:0/035> MLO
<ID:0/035>
<ID:0/035> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1 )
PLEASE HELP :crying: :crying:
1) Use a proper thread title; 'Help !!!!' does not cut it. It needs to be descriptive, many people won't even look at your thread with the title you have now. Edit it.
2) Find Hopper8's 'Odin troubleshooting' thread stickied in General, and go through as many of the troubleshooting steps as many times as you need to in order to get a successful flash with Odin. However, be careful you're only flashing I9100G firmware, flashing anything else will brick your phone (like the 3 part firmware linked in Hopper's thread which can be useful in some situations, do not flash this as it's for I9100).
Do not come back to this thread and say 'But I've tried blah blah blah blah'. You are the only person who can fix your phone at this point, nobody here can do this for you. And by referring you to that thread, I've given you the tools with which you can get it done.
You're welcome.
can you please send me the thread link
i can't find it
Absolutely not.
Go to the General section, the stickied threads are near the top 'Guide - Troubleshoot a failed Odin flash'.
Keep posting to multiple threads about the same issue & you'll probably find yourself banned. Which means your phone stays busted.
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
simonheros said:
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
Click to expand...
Click to collapse
it seems I flashed my International I9300 to a different device (SGH-I747)??? what does this mean? flashed SGH-I747 firmware in I9300? just want to make sure that what i understood is right because your post is making some confusion..
Can you tell me if your device is 16GB or 32GB or 64GB? pit file for all three of them is different. if you will use correct one than this should not fail.. i dont think that mtp has to do anything with odin but if it does than uninstall all the drivers that are currently install(your device drivers) and download and install samsung drivers from here: http://www.mediafire.com/?7iy79emc0bf1fb4 and then try to connect the device again.. I hope this helps you..
suyash1629 said:
it seems I flashed my International I9300 to a different device (SGH-I747)??? what does this mean? flashed SGH-I747 firmware in I9300? just want to make sure that what i understood is right because your post is making some confusion..
Can you tell me if your device is 16GB or 32GB or 64GB? pit file for all three of them is different. if you will use correct one than this should not fail.. i dont think that mtp has to do anything with odin but if it does than uninstall all the drivers that are currently install(your device drivers) and download and install samsung drivers from here: ----------- and then try to connect the device again.. I hope this helps you..
Click to expand...
Click to collapse
Thank you for the response.
Yes I flashed I747 firmware in I9300. I apologize for the poor wording. My device is 16 GB. The one from the thread I linked is said to be used by 16 GB variant, so I believe it works. (Passes)
I don't get that MTP driver error anymore, but now when I try to put a Bootloader in it says that it's an unsupported dev type.
A person got a similar problem here : s3forums.com/forum/galaxy-s3-help/5772-stuck-download-mode-diffrent-device-type-9300-sgh-i747 ( can't post link) but it appears to be bricked flat out...
simonheros said:
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
Click to expand...
Click to collapse
I think mate you should check if your bootloader in locked or unlocked. As you mention above about QualComm Secure boot :Enable. may be before you was using gt-i9300 firmware it must be unlocked but after you flashed wrong firmware may be your bootloader got locked.
try to download complete stock 4.3 firmware from sammobile.com for correct variant i.e GT-I9300.
Download it and extract it and you will get .tar files
download latest Odin ( google it ) and open it.
put your phone in download mode by pressing volume down + home key + power key for few deconds until download mode screen appear.
press volume up key to goto download mode. connect your phone to your computer and wait till it install all the necessary driver. if you drivers are not installed properly then you have to manually installe the driver for your phone. download galaxy toolkit for s3 from xda and install it. search for the folder name galaxy toolkit in your computer. basically it will be in c:/ drive. open that folder and you will find driver folder under it. Inside the driver folder there will .exe file of driver. but before installing disconnect your phone computer and then install the driver. after the installation of your driver plug in again and wait till it install all the drivers.
Inside odin you must have to see that there is COM ID in 1st box and below it is written attached. if you dont see that then your driver are not installed correctly. uninstall and install it again.
after the driver install click on AP and select the AP .tar file that we extracted after downloading. select the appropriate file associated with it.
click on start and wait few minutes till the process gets complete.
If all things goes right you may get your phone back again.
Mustakim_456 said:
I think mate you should check if your bootloader in locked or unlocked. As you mention above about QualComm Secure boot :Enable. may be before you was using gt-i9300 firmware it must be unlocked but after you flashed wrong firmware may be your bootloader got locked.
try to download complete stock 4.3 firmware from sammobile.com for correct variant i.e GT-I9300.
Download it and extract it and you will get .tar files
download latest Odin ( google it ) and open it.
put your phone in download mode by pressing volume down + home key + power key for few deconds until download mode screen appear.
press volume up key to goto download mode. connect your phone to your computer and wait till it install all the necessary driver. if you drivers are not installed properly then you have to manually installe the driver for your phone. download galaxy toolkit for s3 from xda and install it. search for the folder name galaxy toolkit in your computer. basically it will be in c:/ drive. open that folder and you will find driver folder under it. Inside the driver folder there will .exe file of driver. but before installing disconnect your phone computer and then install the driver. after the installation of your driver plug in again and wait till it install all the drivers.
Inside odin you must have to see that there is COM ID in 1st box and below it is written attached. if you dont see that then your driver are not installed correctly. uninstall and install it again.
after the driver install click on AP and select the AP .tar file that we extracted after downloading. select the appropriate file associated with it.
click on start and wait few minutes till the process gets complete.
If all things goes right you may get your phone back again.
Click to expand...
Click to collapse
Thank you for the response.
Drivers work and it's been able to connect to ODIN but it fails regardless of the stock firmware I flash via PDA.
I get this :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLH1_I9300OLBBLH1_I9300DXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
For Bootloader
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----
It would help to mention that I have a second i9300 that works and hasn't been touched or anything. Can I do something with that?
edit* It says unsupported dev type on my screen when it fails..
simonheros said:
Thank you for the response.
Drivers work and it's been able to connect to ODIN but it fails regardless of the stock firmware I flash via PDA.
I get this :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLH1_I9300OLBBLH1_I9300DXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
For Bootloader
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----
It would help to mention that I have a second i9300 that works and hasn't been touched or anything. Can I do something with that?
edit* It says unsupported dev type on my screen when it fails..
Click to expand...
Click to collapse
Looks like your Nand maybe corrupt try flashing the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
tallman43 said:
Looks like your Nand maybe corrupt try flashing the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
Click to expand...
Click to collapse
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
SECURE CHECK FAIL : PIT
Unsupport: dev_type
---
None of the PIT's work now... And pretty much none of the files passed... D:
simonheros said:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
SECURE CHECK FAIL : PIT
Unsupport: dev_type
---
None of the PIT's work now... And pretty much none of the files passed... D:
Click to expand...
Click to collapse
Any progress??
suyash1629 said:
Any progress??
Click to expand...
Click to collapse
None what so-ever. I hit a dead end and had to get a replacement.
I'm just not going to mess with the new one anymore...
Hey all,
So here's the thing; I put my gt-i9300t (non-rooted) phone on charge last night and woke up this morning to the samsung logo screen. A little research and time told me it should be fixable. Some suggested Kies, enter the model and serial and get back to stock. That's great, except I downloaded and installed Kies, only to have it reject the model and serial number combination. Sure I noticed it was case sensitive, but even using either case, the issue could not be overcome. So, I moved on to Odin and the information I found re SamMobile. Did I download and install Odin - yep, all good. How about finding the firmware that was stock for my phone? Yep, 2 hour download no issue.
Was I able to put the phone into download mode? Sure, easy as. Did Odin detect it as a port number via usb, it did at that. Once I extracted the rom, I told Odin to use it as an AP file and made sure re-partition was not ticked. It takes about 30 seconds to check the md5 and load the firmware, when it's ready I click on start. Instead of getting the expected result, I get the below error.
If someone could point me in the right direction it would be appreciated. Objective is to get it working.
Cheers
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> tz.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Please do not use the XDA Assist section for questions like this. You are best to post within your device Q&A.
Your thread has been moved for you.
Thank you,
TonyStark
TonyStark said:
Please do not use the XDA Assist section for questions like this. You are best to post within your device Q&A.
Your thread has been moved for you.
Thank you,
TonyStark
Click to expand...
Click to collapse
Can you provide a link to the thread in q&a please. I have searched for it but it doesn't come up. I have also gone page by page in the q&a doing search on my login name but it finds no threads. I'm assuming I'm looking ni the wrong place, but it's a big site...
Cheers
There is much to be read in this thread. Read through it, you should be able to find what you are looking for.
First of all,I did everything step by step to install a custom rom to my Samsung Fascinate but odin says "Setup connection....
"All threads complete (success 0/failed 1)
Then,after my phone got bricked,I tried installing a stock rom, but the same thing happened :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CI500_VZW_EH03_GB_CM.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
PLEASE HELP NEEDED I AM REALLY TENSED :crying:
Did you ever find a solution to your issue? I am having the same issue but I paid OneClickRoot to Root my device for me and they screwed it up and are pretty much throwing their hands up about it. I am still giving them the chance to make it right but my patience are wearing real thin.
To save you as long as it is not hard bricked, follow these steps.
Get this file.
https://gofile.io/?c=tJd0Pd
Then get odin v1.85
https://gofile.io/?c=WHkZHO
Launch odin with admin powers (sudo/su for linux, or whatever).
Then click PDA and select the tar.md5 file and start.
And please make sure you got the drivers and that a COM port does show up in odin.