Related
Alright so here is the premise. I had a good ol time trying to figure out what to download and where to go, what to do, etc, so i thought i would give anyone interested a step by step tutorial (only for you alltel people, vzw can fend for themselves). Please read all the instructions before you do anything, i can jump around a bit sometimes.
Yes, this should enable your GPS and Rev A. No, I will not be responsible if you destroy you phone (although highly unlikely...)
1. download the newest bootloader.
1a. file can be found here
1b. install the bootloader.
1c. this opens up a dos prompt. read it carefully and make sure your phone is already connected when you open the application.
1c. i believe the second time it asks you to "press a key to continue" you need to disconnect your phone and plug it back in. it tells you to do this so just read the directions.
1d. if it reads out that your phone cant be contacted and to check your cable, its probably because you didnt do step 2b.
2. download and install the new radios.
2a. Dont freak, we are going to download a sprint rom.
2b. Download it from here
2c. Run the exe with your phone plugged in.
2d. IMPORTANT: Once the flash is done, the phone will boot up. It will ask you to tap the screen to begin. If you tap, you Fail. Dont tap the screen.
2e. Move to step three.
3. Almost there, now we are getting a good ol' cooked ROM to run on it.
3a. Download DCD's kitchen here. You will also need to download Visual C++ and .Net Framework from here and here
3b. Once downloaded, click on build rom, you will see a bunch of fancy command prompt windows. Just let it sit there for a while. You will see a window come up with a bunch of check boxes. Really click whatever you want. The default selections should be enough to satisfy you. The only thing you need to make sure to do is click on "Alltel" in the carrier screen and click off of "Sprint", the default.
3c. Once you have selected what you want (again I encourage to just use the defaults and maybe add office or entertainment or something), then click the play button at the top. Once the window shows its done loading, click the x to close out of the builder. The command prompt window will start spewing information again at you. Disregard that, its not really vital.
3d. After the command prompt finishes the tizzy it got itself into, the HTC flashing application will automatically launch. Follow through in this window and it will eventually flash you phone. Thats really all you have to do!
Final Thoughts: This guide will also work with any of the other carriers that DCD's new kitchen supports. Thats pretty much everyone because, he is, you know, the man and all. The only thing you have to change is the selection of you carrier when you are "building" your rom. For the specifics of this guide I choose alltel but you can use whatever you want assuming it matches your carrier.
Please write down your Programming information before you do this flash. And its important to know your MSL if you have one of those BS carriers that changes it (unlike alltel). If you need to reprogram your phone, dial ##000000+send and put in your nam information. If you need to still set you A-Key or HDR password (more advanced stuff, the A key allows some sort of authentication and HDR password (located in the security section) allows you to connect to EVDO networks) then you can access the more advanced EPST menu with ##778+send.
Make sure you update with *228 to get the latest PRL or search around online.
Happy Flashing!
Feel free to send me a message if you have any questions or if i left something out
ALSO THANKS TO EVERYONE WHO MADE THIS POSSIBLE AT XDA, GREATEST PHONE SITE IN EXISTENCE
Finally, a step by step for Alltel folks...Thanks. My head was spinning trying to piece together everything from all the various posts.
Terrific write up.
If you can, include where to find the MDN, MSID, and AKEY before upgrading so that these can be re-installed if erased...
Old roms don't work
Nice guide, but you should also note that older roms have a compatibility issue with the new radio upgrade. it seems right now only dcd's cooked rom works; for me at least.
The information you are looking for can be found by using the advanced EPST feature in the phone. assuming you are using a stock dialer (or one that supports codes) inut "##778" and then press call. it will bring up a menue and ask to view or edit. If you are getting your info, of course, press view and if you are replacing info, just click edit. all the info like your mdn and min (which you should know without having to look in here) will be here. clicking the menu on the taskbar will let you choose an entire metric ****ton of info to view. a key is one of them. I noticed now that going back, my akey is not inputted. i dont know what this value is but in the past i think i have seen it as just "0" or blank. I was foolish and didnt write it down before the flash. if anyone has anything diferent in their akey, wanna post it?
update prl
alright so i think i solved the problem with the roaming issue and the EVDO connectivity. and i feel like an idiot. for some reason i just kept on putting off updating the prl since i flashed it. and for another reason i didnt think it would matter. but i have since used the latest prl and updated completely and, wouldntyouknowit, it works perfect. steps?
1. download the newest prl here.
2. bluetooth or copy to your phone
3. open the dialer and press "##775" (this spells prl)
4. enter your unlock code, should be 000000
5. click on update prl, then menu at the bottom then edit
6. browse to where the prl is on your phone (probably my docs if you BTed it)
7. update and restart, voila!
8. enjoy having EVDO and no triangle again! WOOT!
just wondering, after following through all those steps, do we need to relock it?
Also want to note that, this method does indeed work for all providers (alltel, vzw, sprint), it's just the step where you have to flash your rom (DCD's or any other) make sure it is the one with your provider. I made a mistake of downloading the Alltel rom when I'm really a Sprint user :x.
Have any of you folks been able to get OfficeSync to work with this ROM? I can surf the web but am unable to register with my account.
I was hung up in between steps 2 and 3. The screen was stuck on the Alltel screen and I couldn't connect with my pc to install the ROM. I followed other instructions to use a FAT32 formatted SD card with the ROM renamed to TITAIMG.nbh. Reset into bootloader mode by holding the power and camera buttons and hard reset. Run the setup from there... Hope this helps someone else.
Total_Lag said:
just wondering, after following through all those steps, do we need to relock it?
Also want to note that, this method does indeed work for all providers (alltel, vzw, sprint), it's just the step where you have to flash your rom (DCD's or any other) make sure it is the one with your provider. I made a mistake of downloading the Alltel rom when I'm really a Sprint user :x.
Click to expand...
Click to collapse
I never locked my phone and it works fine. So I am guessing no, you dont. And yeah you are correct it should work fine with any of DCD's roms, i just know the alltel one was a success for me, didnt want to lead someone astray. I know the telus one, for example, was bugged at first. idk
This is my first modification to my cell phone...just got it! Is there a setting I check to verify the GPS is working? I just looked around and all I saw were settings for connectiong external GPS devices. Also, when i go to communications manager...there is no setting for GPS. Shouldn't there be a way to turn GPS on and off? Thanks for the help!
Ok....I don't think mine is working because I installed Google Maps and clicked track location and it just stayed at Contacting Satellites (0)...I think I may have messed it up because I installed the SPL first, then the DCD's OS and last the radios...i went back and tried to reinstall everything int he correct order, but now the radio ROM says it's not created for my device.
Is there a way to start over with a fresh install so I can try this again and do it in the correct order this time? Please help! Thanks!
Well im having problems. I installed the new rom via sd card. Everything seemed to go smooth, but when wm starts up and goes through the align screen thing it just restarts and never starts up.
bond00 said:
Ok....I don't think mine is working because I installed Google Maps and clicked track location and it just stayed at Contacting Satellites (0)...I think I may have messed it up because I installed the SPL first, then the DCD's OS and last the radios...i went back and tried to reinstall everything int he correct order, but now the radio ROM says it's not created for my device.
Is there a way to start over with a fresh install so I can try this again and do it in the correct order this time? Please help! Thanks!
Click to expand...
Click to collapse
If you want to start from a blank slate you should be able to install a factory ROM and then begin again from there. It's my understanding that the proper order should be: New SPL --> DCD's ROM --> New Radio
I myself, when following this order, got stuck at the Alltel splash screen after I installed DCD's ROM, but before installing the radio. A reboot with the camera and power buttons held down simultaneously got me into bootloader. From there the ROM installer could recognize the device and proceed with the radio install.
If you click on the data arrow icon at the top, what does it say?
Mine says:
"Alltel Wireless (Dial-up) Connected"
I cant remember before what it said when connected but my download high was 497kps & 97kbps for upload. Either the area I am in doesnt have Rev A (Which I think is the case based upon EVDOMAPS) or my data connection is now hindered...
xweaponx said:
If you click on the data arrow icon at the top, what does it say?
Mine says:
"Alltel Wireless (Dial-up) Connected"
I cant remember before what it said when connected but my download high was 497kps & 97kbps for upload. Either the area I am in doesnt have Rev A (Which I think is the case based upon EVDOMAPS) or my data connection is now hindered...
Click to expand...
Click to collapse
I personally have not been able to reach an EVDO signal at all. in an area where i was always at EVDO, now im mostly shown as roaming and in 1x. I have most recent prl and my SIDs are correct. i think there is a reason this rom is still in beta....
Have you tried the *228, press 3 then *228 then press 2? I had the roaming indicator flashing with 1X until I completed the steps above...
axcess shop
downloaded wm6.1 and it work great but is there a way to get alltels axcess shop back or no thank you
evdo
i am not romeing but i cant get a go evdo ether just 1x i did *228 and still only get 1x any way to fix this thank you
Check my Reply in this Post! The instructions will get your phone locked back onto EVDO. Not sure what your problem is with the roaming, haven't had any problems with that. I would recheck the SID in EPST again!
http://forum.xda-developers.com/showthread.php?t=366068
Hello all,
Last night, I tried updating my Rom on a sprint mogul to the recent dcd 2.2.6 and 3.27 radio.
I followed the steps of taking down the information, finding my unlock code, unlocking, and updating both roms.
It went with no problems. However my MSID was reset so i had to enter my unlock code that i got from get spc. before i reflashed my device, i checked to see if the code worked by trying to enter and edit epst.
But in windows 6.1 the unlock code didnt work, my msid and mdn were set to all 0.
I called sprint they gave me the same unlock code that didnt work.
So i tried reflashing back to the original sprint official release, that didnt work, i was getting an error 328 from the ruu.
I tried reflashing again dcd 2.2.6 rom, that worked but the radio wouldnt flash due to the same invalid command error 328 from the ruu.
So for a while i was stuck on the htc splash screen with a no radio display. I found a thread with a solution to the same problem. I flashed the leaked sprint rom 3.16, that worked and i was able to get up and running.
However in epst mode my hex and dec esn are all zeros. my original unlock code doesnt work, (the one from sprint), but when i enter in all 0 in getspc it generates the proper unlock code,
but i still can not connect to the sprint network even tho i am able to set my msid and msn to the correct values, my esn is still wrong (displays all zeros)
Can any please tell me if i can fix this, I was on the phone with sprint for 2 hrs with no avail. I need to set my esn on the phone to match my esn in hardware
Thank you,
Kevin
Okay, if I read your post right you do have your MSL number (unlock code) right? If you do, go to your keypad on the phone and dial ##3282# (##DATA#). It should ask you if you want to view or edit. Choose edit and type in your MSL number. On the main screen there should be an option on the left softkey that says "View Info". Choose that and then select "Advanced". At the top I believe you can edit your ESN number.
Hope that helps.
krazieintentz said:
Hello all,
Last night, I tried updating my Rom on a sprint mogul to the recent dcd 2.2.6 and 3.27 radio.
I followed the steps of taking down the information, finding my unlock code, unlocking, and updating both roms.
It went with no problems. However my MSID was reset so i had to enter my unlock code that i got from get spc. before i reflashed my device, i checked to see if the code worked by trying to enter and edit epst.
But in windows 6.1 the unlock code didnt work, my msid and mdn were set to all 0.
I called sprint they gave me the same unlock code that didnt work.
So i tried reflashing back to the original sprint official release, that didnt work, i was getting an error 328 from the ruu.
I tried reflashing again dcd 2.2.6 rom, that worked but the radio wouldnt flash due to the same invalid command error 328 from the ruu.
So for a while i was stuck on the htc splash screen with a no radio display. I found a thread with a solution to the same problem. I flashed the leaked sprint rom 3.16, that worked and i was able to get up and running.
However in epst mode my hex and dec esn are all zeros. my original unlock code doesnt work, (the one from sprint), but when i enter in all 0 in getspc it generates the proper unlock code,
but i still can not connect to the sprint network even tho i am able to set my msid and msn to the correct values, my esn is still wrong (displays all zeros)
Can any please tell me if i can fix this, I was on the phone with sprint for 2 hrs with no avail. I need to set my esn on the phone to match my esn in hardware
Thank you,
Kevin
Click to expand...
Click to collapse
thank you for your reply.
I do have my unlock code. the ##data# shows the esn in advanced settings, but the box is greyed out and will not allow me to edit it.
It still shows 00000000.
Thank you, any other ideas, maybe a registy edit?
It sounds like something happened during the flash process. I talked to a PCS rep and they said you would have to bring it in and get it swapped. I can't think on any other way to get that info updated. Sorry.
no there is another way, you can sniff for the spc, the original thread about getspc had directions @ ppcgeeks
dalvarez7 said:
Okay, if I read your post right you do have your MSL number (unlock code) right? If you do, go to your keypad on the phone and dial ##3282# (##DATA#). It should ask you if you want to view or edit. Choose edit and type in your MSL number. On the main screen there should be an option on the left softkey that says "View Info". Choose that and then select "Advanced". At the top I believe you can edit your ESN number.
Hope that helps.
Click to expand...
Click to collapse
You need ths link
http://forum.ppcgeeks.com/showthread.php?t=17495&highlight=getspc
I went to a sprint tech and they said they i had to replace the phone, and they would order me a new one. but right now i have to wait the warehouse doesnt have any instock.
there is another way however, if it was erased by software, it can be changed by software.
I did not find anything relevant on the link above, i will keep looking through it. If someone could point me in a closer direction.
I do have my unlock code, currently all zeros, so im not looking to get my MSL number, im looking to change my ESN back to what it was, somehow it was set to all 0's during the rom update process.
Thank you,
Kevin
Perhaps you should change the thread title to something more specific to separate yourself from the masses who can't boot because they didn't upgrade their radio.
Perhaps try an RTN reset? This is a hard reset that erases provisioning data. I don't know if it can restore an ESN, but worth a try.
Go to dialer
##786# (##RTN#)
Menu->reset
krazieintentz said:
Hello all,
I followed the steps of taking down the information, finding my unlock code, unlocking, and updating both roms.
Click to expand...
Click to collapse
Is it just me or does something seem wrong with this quote. Read the instructions here: http://forum.ppcgeeks.com/showthread.php?t=17667
The phone needs to have the unlocker program run to install a custom rom. The code from GetSPC allows you to edit the settings not unlock your phone.
hohnan said:
Is it just me or does something seem wrong with this quote. Read the instructions here: http://forum.ppcgeeks.com/showthread.php?t=17667
The phone needs to have the unlocker program run to install a custom rom. The code from GetSPC allows you to edit the settings not unlock your phone.
Click to expand...
Click to collapse
Look i dont need any smart comments.
Well actually for your information, the MSL code is used to unlock your phone. the unlocker program is used to unlock your bootloader to accept a custom rom.
MSL - master subsidy lock, this locks network settings so that a user can not change them, the code given by getspc is stored in nV ram on the phone and is used to gain access to these files, thus "unlocking" the phone. unlocking the bootloader is another story...
anywho, i was able to get my phone working, i reprogrammed my esn, reprogrammed my MSL from all zeros to the proper value, and now my phone is back on the sprint network.
if you guys are interested i will write a tutorial on how i did this, just to respond to the other post, a hard reset does not restore esn data.
Good for you! I'm glad you figured it out. I would be interested on how you got it working again.
krazieintentz said:
Look i dont need any smart comments.
Well actually for your information, the MSL code is used to unlock your phone. the unlocker program is used to unlock your bootloader to accept a custom rom.
MSL - master subsidy lock, this locks network settings so that a user can not change them, the code given by getspc is stored in nV ram on the phone and is used to gain access to these files, thus "unlocking" the phone. unlocking the bootloader is another story...
anywho, i was able to get my phone working, i reprogrammed my esn, reprogrammed my MSL from all zeros to the proper value, and now my phone is back on the sprint network.
if you guys are interested i will write a tutorial on how i did this, just to respond to the other post, a hard reset does not restore esn data.
Click to expand...
Click to collapse
I also would be interested
dalvarez7 said:
Good for you! I'm glad you figured it out. I would be interested on how you got it working again.
Click to expand...
Click to collapse
This would be a handy bit of knowledge as they go thru great lengths to keep it from being done. Ususally the filesystem for that section of the phone is locked and protected, requiring the QXDM (Qualcomm Extensible Diagnostic Monitor) software to get in. I have an older version that I used to use to play with older phones and it worked great, but a newer one would be needed for these phones. Old style glitch corruption will mess up any filesystem and even mess up protected areas, which is likely what happened to yours. I would love to know how you did it without QXDM ;-)Thanks.
krazieintentz said:
Look i dont need any smart comments.
Well actually for your information, the MSL code is used to unlock your phone. the unlocker program is used to unlock your bootloader to accept a custom rom.
MSL - master subsidy lock, this locks network settings so that a user can not change them, the code given by getspc is stored in nV ram on the phone and is used to gain access to these files, thus "unlocking" the phone. unlocking the bootloader is another story...
anywho.........
Click to expand...
Click to collapse
Wow. A pretty harsh response to someone who was trying to help out.
A tutorial will be nice. if you have the time!
krazieintentz said:
Look i dont need any smart comments.
Well actually for your information, the MSL code is used to unlock your phone. the unlocker program is used to unlock your bootloader to accept a custom rom.
MSL - master subsidy lock, this locks network settings so that a user can not change them, the code given by getspc is stored in nV ram on the phone and is used to gain access to these files, thus "unlocking" the phone. unlocking the bootloader is another story...
anywho, i was able to get my phone working, i reprogrammed my esn, reprogrammed my MSL from all zeros to the proper value, and now my phone is back on the sprint network.
if you guys are interested i will write a tutorial on how i did this, just to respond to the other post, a hard reset does not restore esn data.
Click to expand...
Click to collapse
Krazeintentz,
I would be very interested in your final fix for this problem. The exact same thing happened to me a while back and my only way out at the time was a replacement titan under warranty from vzw.
If we had your steps to recovery then we would be a lot closer to having a disaster recovery wiki.
As another poster said, yours was a real rom flashing problem as opposed to the numerous "brick" cases that we see everyday from just half done flashes. So it makes it all the more relevant that we have a wiki for this problem.
Regards
Since he has not said, heres a theory
The filesystem is protected from editing in the address range where the ESN resides. The QXDM software shows the actual file structure of the chipsets flash and the files have actual attributes and the ESN file is read only, so the EPST is not supposed to be able to edit the ESN (as this would be cloneing a phone and not legal). If you follow the steps in a flash memory update, you would see that the contents of these protected files are read, saved, and then the flash is totally erased, then written with the new revision, and finally the protected storage is written and the attribute is set to read only. The QXDM is required to manually unlock these attributes, but there is a key that allows the flash utility to erase the stuff. if the flash was interrupted either by hardware or software error at the point after the erase and writeback but before the write of protected file area, the ESN would be blank and also the EPST in the phone would be able to edit it in edit mode because the attribute is the very last thing written. I bet thats how he fixed it and now has a cloneable phone too and can change his ESN any time he wants, at least until he flashes the radio again which will fix the glitch by process. Thats probably what he did.
Hey guys Im a noob and im having a bit of problems
Im stuck in the bootloader screen
TITA100 MFG
SPL-2.40 Olipro
CPLD-9
My comp has windows vista premium so instead of activesync i have windows device center 6.1 I have unclicked allow USB connections
but i think my comp doesnt recognize that they the phone is connected at all although i do here the sound that lets me know that a usb device is connected
exitbl.exe doesn't work keeps telling me
cannot open USB port
Please make sure that USB connection in Activesync is disabled
Also make sure that your USB cable is properly connected
if it helps im on a bell phone
**Solved!!!**
Uploaded correct files to megaupload - http://www.megaupload.com/?d=I204KSNF
OUT OF THE BOX FRESH FEELING FOR YOUR XV6800!
Radio: 1.30.60
Rom: 2.09.605.8
Rom Date: 08/03/07
full restore of all original settings!
nuguys solution said:
Be connected to activestink.
(even if your device only boots to the windows splash screen activestink can still connect enough to load this 1.2 bootloader)
Run TitanUnlocker.exe from first folder
FOLOW THE ON SCREEN DIRECTIONS EXACTLY
INCLUDING THE UNPLUGING AND PLUGING BACK IN PART
Be patient and be sure that it is complete.
Then without disconecting, or restarting your device
go to the second directory and folow these directions...
While stil in bootloader mode run ROMUpdateUtility.exe
Follow the onsreen directions.
When your device boots up - LET THE VERIZON CUSTOMIZATIONS RUN.
Enjoy being back on Verizons service.
Now go load whatever roms you feel comfortable running.....
You may need a different bootloader for some roms.
Click to expand...
Click to collapse
I let the customizations run after loading the SPRINT 3.35 Rom updater on my XC6800, I don't think the problem was loading the rom, but letting the damned sprint customizations install instead of a quick reset.
*
I have tried a hell of a lot to resolve this and am convinced that at this point it is going to take a verizon stock rom - the whole thing - to start from scratch and get back from the evil grips of those sprint towers (you sprinters would think the same if in our shoes)...
*
Unfortunately I have not found everything to piece together an entire orig vz rom.
*
The first bad thing that the sprint customizations does is resets the MSL, so now instead of using 000000 as always, you have to find "GetSPC", run it giving it your ESN (under battery) to find out your new "sprintized MSL". This causes you to use sprints towers for everything, add to the fact that it loads a sprint PRL and you are now "stuck on sprint".* when you dial *228 you get a sprint recorded voice that this number is not valid.
Having a xv6700 laying around I was able to set nearly everything in EPST back to where it needed to be (see screen shots)- that got me making calls (roaming) but no i-net, and no *228...
*
Called Data tech support for a aKey, they gave it to me, that didn't work.
*
Dl'ed a vz PRL from http://www.corolada.com/prl/
That got me to be able to connect to vz by dialing *228, but no love, it says "sorry call cust serv...".
*
Went to a corp VZ store and looked at all the settings in EPST changed a couple more, that didn't work.
*
Spoke to the lead geek in charge there and fessed up, he said that it was because of the MSL code change, that *228 sends the 000000 “service sub lock code” to unlock the SPL (EPST) and if the code is different, it will never connect to *228 right (well maybe after they open up their network more, but that is at least months away).* So I said what if I was with sprint and wanted to "convert"? He said they would need sprint to set the MSL to 000000, which would likely be done by sending it in to sprint, then sprint sending it to HTC (I'm sure we can come up w/ something better).
*
After leaving, I received a follow up call from my escalated trouble ticket, and the girl reset my “DMU keys” that finally got me to have i-net (still no *228 love though).
*
So now I am at a OK place, everything works but still roaming, place and receive calls, received network texts from cust serv, and have i-net. However I didn’t want to go through all the set up on my phone just to hard reset anyway so I started off on a quest to find a legit vzw rom.
People keep saying it's posted here, or there or everywhere, I HAVE TRIED everyone I have found and have NOT been able to reset the radio to Verizons peramaters.
Any help out there as to finding the STOCK VERIZON RADIO or best the whole stock verizon rom package?
for those who need help getting the EPST setup I will post the current settings I am using in screenshots.
** I will update this post to reflect the best solution if the thread gets cumbersome.
I used the stock Verizon ROM at:
ftp://up.ppcgeeks.com/Titan/CarrierRoms/Verizon_Stock_ROM/VZW_Passworded_Ruu_signed
I had a similar type issue and I'm working fine now. You'll see a solved post from me with a GPS issue. Hope that helps.
starting to agregate info
starting to agregate info:
Geckotek said:
Here is a repost of my earlier posting on this subject. This will resolve your issues if your Verizon phone has been "Sprintized" or help you restore your phone before returning it to Verizon.
To set your phone back to the default Verizon ROM, do the following:
Download all necessary files 1) Titan Re-locker 2) Stock Verizon ROM 3) ROM Update Utility
Unzip/rar the Stock ROM and the RUU (unrar using WinRAR) ****DO NOT UNZIP THE RELOCKER**** (it is a self extracting zip and will run properly as is)
Place the Ruu_signed.nbh file in the RUU folder
Hard reset your phone by holding down both softkeys, hitting reset, and pressing R (just for good measure)
Connect your phone to your PC and make sure ActiveSync is connected
Re-lock your phone by running Titan_Relocker.exe
Place the stock Verizon ROM in the RUU folder
Run the RUU by running ROMUpdateUtility.exe
For good measure, let the Verizon ROM complete its setup.
I'm doing this from memory so please let me know if I missed a step so that I can update this post.
I hope this is helpful.
Edit: links corrected
Click to expand...
Click to collapse
Geckotek said:
xv6800
Was running 2.3.2 w/ the 3.27 radio. Just updated.
Here were my steps:
Performed hard reset
Connected phone to PC and made sure AS was connected
Ran the Sprint updater
Upon reboot I forced phone into bootloader mode (did this while HTC screen was beginning to appear)
Cooked ROM in DCDs Kitchen...added several options
Ran updater
Notes:
Never had to run *228. Phone and internet confirmed to work correctly. Syncing w/ AS right now, configuring Exchange AS.
Will report back more later, but so far so good.
Click to expand...
Click to collapse
ebb said:
(coming from DCD 1.70 and radio 2.13)
1. Load Olipro 1.20 unlocker (my phone was re-locked after 1.70 ROM)
2. Flash radio
--Reboot was stuck on verizon screen after radio- entered bootloader mode by pressing power+camera, and inserting stylus for reboot. Entered bootloader successfully.
3. Cooked verizon-based rom from DCD 3.0.0 kitchen
4. Flashed ROM
This brought me to the new radio and rom, BUT... when disconected from the desktop, entered the dreaded constant reboot situation, so...
5. Reattached to desktop- this stopped the rebooting. Established activesync.
6. Loaded Olipro 2.40
7. Removed connection from desktop. Removed battery and after reinsert, hard reset device.
8. Ran *228,1 and then *228, 2. Soft reset after each
9. Working great for phone and text. Will play with GPS and report back (yes-- I will enable Location On!)
Thanks DCD for your great work and suggestions along the way here and in the radio thread..
Click to expand...
Click to collapse
Geckotek said:
So to summarize your steps minus the failure follow my directions but if you don't have Olipro 2.4 installed already, do that first. OH, and I didn't need to run *228.
My data speed didn't test so well...gonna see if running a *228 helps.
Edit: HA! As I expected...running *228 jacks me up again. Looking for signal. *22802 kicks it back into signal.....looking into it some more.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=376873
Geckotek said:
http://forum.xda-developers.com/showthread.php?t=376873
Click to expand...
Click to collapse
your solution is finaly correct - I am uploading the needed files to megaupload so ftp issues don't keep causing problems for people.
I am stuck at the verizon white splash screen and I am trying to get my phone back to stock. I can not establish a connection to my PC via active sync. It there a way to get my phone connected, or is my phone Brick'd now?
Thanks
mcgong said:
I am stuck at the verizon white splash screen and I am trying to get my phone back to stock. I can not establish a connection to my PC via active sync. It there a way to get my phone connected, or is my phone Brick'd now?
Thanks
Click to expand...
Click to collapse
Press camera+power+soft reset
This will take you to the boot screen and you should be able to continue. You should have relocked your bootloader, right?
If so, just go ahead and flash the stock rom.
EDIT: Dont panic. If you are at the Verizon screen your phone is definitely NOT bricked. There are HUNDREDS of cases exactly like your and HUNDREDS more posts telling your exactly how to fix your problem. Search and you shall find.
Even before you actualy get into WinMo even though activestink is not really connected - it is able to connect through and re-flash the bootloader - it took a while to figure that one out for me too...
mcgong said:
I am stuck at the verizon white splash screen and I am trying to get my phone back to stock. I can not establish a connection to my PC via active sync. It there a way to get my phone connected, or is my phone Brick'd now?
Thanks
Click to expand...
Click to collapse
The moral of the story is, don't let Sprint customization run!
I did and had heck for 2 days. After flashing and re-flashing. i finally got back to original vzw rom, but data still didn't work, even after talking with tech support.
I took my phone to a local vzw store and they were able to fix it.
30 minutes later, I had the dcd3.01 rom installed and everything working perfectly.
Next big rom update, I will wait for others to screw up before jumping in.
....
plz up date the wiki with this
I did that same thing a month ago. Ran the damn Sprint Radio/Rom package and was stuck on Sprint towers. Even going back to the stock Verizon rom didn't help. I manually loaded a PRL and finally had phone calls, but no data. After many hours on the phone with Verizon giving me AKEYs, refresing towers, releasing stuck data sessions.... They finally sent me a replacement phone. Nice to see this issue has finally been resolved.
vx6800 bricked
I am new here but I need some help.
I have read and reread all the various posts but cannot get past the splash screen. During startup, at the bottom it, i get R 1.30.60 and D 3.35. It appears my problem is mismatched ROM and Radio version. However, trying to get back to stock rom, my device is not even detected by activesync and no matter what I do, I end up getting error - device not connected.
Thanks
benji
nuguy said:
**Solved!!!**
Uploaded correct files to megaupload - http://www.megaupload.com/?d=I204KSNF
OUT OF THE BOX FRESH FEELING FOR YOUR XV6800!
Radio: 1.30.60
Rom: 2.09.605.8
Rom Date: 08/03/07
full restore of all original settings!
I let the customizations run after loading the SPRINT 3.35 Rom updater on my XC6800, I don't think the problem was loading the rom, but letting the damned sprint customizations install instead of a quick reset.
*
I have tried a hell of a lot to resolve this and am convinced that at this point it is going to take a verizon stock rom - the whole thing - to start from scratch and get back from the evil grips of those sprint towers (you sprinters would think the same if in our shoes)...
*
Unfortunately I have not found everything to piece together an entire orig vz rom.
*
The first bad thing that the sprint customizations does is resets the MSL, so now instead of using 000000 as always, you have to find "GetSPC", run it giving it your ESN (under battery) to find out your new "sprintized MSL". This causes you to use sprints towers for everything, add to the fact that it loads a sprint PRL and you are now "stuck on sprint".* when you dial *228 you get a sprint recorded voice that this number is not valid.
Having a xv6700 laying around I was able to set nearly everything in EPST back to where it needed to be (see screen shots)- that got me making calls (roaming) but no i-net, and no *228...
*
Called Data tech support for a aKey, they gave it to me, that didn't work.
*
Dl'ed a vz PRL from http://www.corolada.com/prl/
That got me to be able to connect to vz by dialing *228, but no love, it says "sorry call cust serv...".
*
Went to a corp VZ store and looked at all the settings in EPST changed a couple more, that didn't work.
*
Spoke to the lead geek in charge there and fessed up, he said that it was because of the MSL code change, that *228 sends the 000000 “service sub lock code” to unlock the SPL (EPST) and if the code is different, it will never connect to *228 right (well maybe after they open up their network more, but that is at least months away).* So I said what if I was with sprint and wanted to "convert"? He said they would need sprint to set the MSL to 000000, which would likely be done by sending it in to sprint, then sprint sending it to HTC (I'm sure we can come up w/ something better).
*
After leaving, I received a follow up call from my escalated trouble ticket, and the girl reset my “DMU keys” that finally got me to have i-net (still no *228 love though).
*
So now I am at a OK place, everything works but still roaming, place and receive calls, received network texts from cust serv, and have i-net. However I didn’t want to go through all the set up on my phone just to hard reset anyway so I started off on a quest to find a legit vzw rom.
People keep saying it's posted here, or there or everywhere, I HAVE TRIED everyone I have found and have NOT been able to reset the radio to Verizons peramaters.
Any help out there as to finding the STOCK VERIZON RADIO or best the whole stock verizon rom package?
for those who need help getting the EPST setup I will post the current settings I am using in screenshots.
** I will update this post to reflect the best solution if the thread gets cumbersome.
Click to expand...
Click to collapse
I got this problem fixed with the help of an uncommonly smart tech support agent.
My first problems started when I accidentally put the sprint rom on my phone and let it boot.
I just called tech support about three times before I saw this post and they couldn't help me and they even did a DMU key reset without my knowledge and that didn't work. The last guy I talked to told me to bring the phone back into the store that I got it to get it replaced. Not wanting to do that beings that this was the last phone the store had in stock, I did one final search on google and found this site. After reading this post, I called back in to ask them to do a DMU key reset. The tech support agent then informed me that they already did a DMU reset and it obviously didn't work. He then wanted to try "something". He asked me to take the battery out of the phone and leave it like that while he put me on hold. I was on hold for about 3 minutes and when he got back on, he asked me to get back onto the phone and asked me to boot the device up again. He then asked me to dial *228 and let the phone reprogram. After I did that and it rebooted, I was able to use data. Whoohooo!!!!
I asked him what he did for my own personal benefit and he informed me that he actually temporarly removed my data package from my plan and reaplied it. But it was important that the device was turned off while he did it. Hence, the removal of the battery. I was very pleased with this guy. I thanked him profusely.
I'm posting this for the benefit of other people who are having problems with their data package after installing the sprint rom.
I haven't posted before, but I have a pretty difficult problem.
I tried installing one of those Sprint ROM/Radio setups on my phone, and like a dummy I let the customizations run. So here's what I did:
1) I flashed back to Verizon stock using the relocker and stock radio/rom. Once completed, it still shows roaming.
2) Then I used *228 option 1, then option 2, and the roaming icon goes away. Oh yeah, I also get the message "we are currently unable to authenticate your phone". No problem, not going to do anything else yet until I get a ROM/Radio combo I want.
3) Then I flashed the unlocker and (insert ROM/Radio combo here). I've tried most of them, following the compatibility list posted on this site. Most version of DCD's, 5067 (or whatever the # is), and radios 3.35, 3.37, 3.39, 3.49, etc. Once I get everything set, get a new A-key, I'm still roaming. The bottom line is that it doesn't matter what I use; the phone goes back into roaming mode. I then tried *228 option 1/option 2. *22899 does not work at all. I've tried to have them do the DMU resets; that doesn't seem to work. I've downloaded and installed new PRL files; that didn't help. In addition to roaming, my data isn't working either. I gave up and reflashed back to stock using the posted procedure.
4) Go back to step 1. I'm somewhere in this endless loop as we speak.
I can't fix it. I've followed almost every recommendation on this site. Verizon is sending me a new phone. In the meantime, I'd like to continue to try to fix this, but I don't know what else to do. Can anyone help???? Thanks.
schoolio said:
I haven't posted before, but I have a pretty difficult problem.
I tried installing one of those Sprint ROM/Radio setups on my phone, and like a dummy I let the customizations run. So here's what I did:
1) I flashed back to Verizon stock using the relocker and stock radio/rom. Once completed, it still shows roaming.
2) Then I used *228 option 1, then option 2, and the roaming icon goes away. Oh yeah, I also get the message "we are currently unable to authenticate your phone". No problem, not going to do anything else yet until I get a ROM/Radio combo I want.
3) Then I flashed the unlocker and (insert ROM/Radio combo here). I've tried most of them, following the compatibility list posted on this site. Most version of DCD's, 5067 (or whatever the # is), and radios 3.35, 3.37, 3.39, 3.49, etc. Once I get everything set, get a new A-key, I'm still roaming. The bottom line is that it doesn't matter what I use; the phone goes back into roaming mode. I then tried *228 option 1/option 2. *22899 does not work at all. I've tried to have them do the DMU resets; that doesn't seem to work. I've downloaded and installed new PRL files; that didn't help. In addition to roaming, my data isn't working either. I gave up and reflashed back to stock using the posted procedure.
4) Go back to step 1. I'm somewhere in this endless loop as we speak.
I can't fix it. I've followed almost every recommendation on this site. Verizon is sending me a new phone. In the meantime, I'd like to continue to try to fix this, but I don't know what else to do. Can anyone help???? Thanks.
Click to expand...
Click to collapse
dang, im here too... any fix?
quadjacks said:
dang, im here too... any fix?
Click to expand...
Click to collapse
Nope. New phone.
schoolio said:
Nope. New phone.
Click to expand...
Click to collapse
Verizon Stock ROM/PRI Update should fix calling
A DMU reset is PROBABLY needed to fix data (need to finango your way around tech support to get one)
scrawnyb said:
Verizon Stock ROM/PRI Update should fix calling
A DMU reset is PROBABLY needed to fix data (need to finango your way around tech support to get one)
Click to expand...
Click to collapse
Nope, did all that too.
schoolio said:
Nope, did all that too.
Click to expand...
Click to collapse
ok i am BACK!!! WOOT|WOOT
here is what i did.
Using the files from post 1 of this thread as no others i tried worked!
1 hard reset
2 ran relocker
3 ran ruu utility
4 allowed cust
5 ran *228
finaly no triangle (raoming icon), but not data
6 called VZW CS, explained i had done a hard reset, BLAH...BLAH...DUH...DUH... not sure why this is happening
a. she had me do everything i had already done (*228), reset username and pass...etc.
b. after 30 mins and at last resort, she removed then readded me to the system (reprovisioned, much like when cable internet modems go offline) SUCCESS
remember only use files from post one of the ablve link, others on here, ppcgeeks, smartphonejunkie oddly didnt help!
Now im back up to Rom 20226 radio 3.42... man im hard headed, but i have a kewl phone again!!!! hope this helps!!!!
NOTE: i was not able to use ##778 to manually program!!!!! so if you have a good tech, this may give him clues to your REAL issue.
also look here post 24
http://forum.ppcgeeks.com/showthread.php?p=271602#post271602
quad,
i am waiting (24 to 48 hrs )for their network team to do.... something to my phone, possibly the DMU reset. My tech wasn't able to do that on her own. I'm wondering if i can get a regular tech to do what they did for you....when you say they removed you then added you to the system, not exactly sure what that means
I'm Jealous.....
EDIT: BTW, my data connection settings won't keep a username and pwd stored....keeps dropping them every time after i put em in
Ok folks. If you are like me, you searched all over the web didnt find a definitive answer on how to go about getting your HTC rezound to Pageplus.
I bought a used Rezound. It came with NO Verizon SIM card. No software updates to it. I read a lot, sounded like getting to the latest stock was a good idea as it usually fixes issues. Well, I promptly updated to the leaked global ICS rom. Go the rom from android police dated Aug 15.
So my rezound had locked stock global ICS rom, no SIM card. Here is how i flashed it to pageplus. Please follow the steps as mentioned, as i have stumbled too many times and got it working.
================================
Not a must but...
1. Dont upgrade your phone to ICS rom if you dont want to root your phone. As ICS blocks APN updates. Meaning if you need 3g on pageplus or any other carrier and you dont want to root your phone, dont upgrade. If you dont mind rooting your phone, you can just ignore this warning.
Requirements:
MIN and MDN Information:
You can get MIN and MDN by calling pageplus or follow steps below.
goto http://www.kittywireless.com/pageplus/phonestatusform.html
right at the bottom you can enter email and phone number. You will get an email with MIN and MDN information.
OS Requirement:
Windows 7 64bit or 32bit. No support for Linux, Mac or XP(??).
Software you will need:
1. HTC Sync http://www.htc.com/us/support/htc-rezound-verizon/software-updates.
2. HTC Diag drivers. You can download from below.
3. QPST. http://conflipper.com/Software/QPST_2.7_366.rar
4. CDMA Workshop. You need the full version. Demo is not useful. There is an old 2.7 cracked version floating around in the web. That will do the job.
Steps to follow:
1. Install HTC Sync. This software will install HTC Sync and HTC Drivers. All you are looking for is HTC Drivers. So, as soon as installation is complete you can uninstall HTC Sync alone. They have seperate uninstallers.
2. Install HTC Diag drivers. Now, i hope you have access to Windows 7. These drivers didnt install in XP for me. it could work for you.
This step is crucial, without these drivers installed you wont be able to do anything.
i. Connect your phone to PC.
ii. Just leave it on charge mode. The HTC drivers you installed in previous step should recognize the phone.
iii. Goto the dialer in phone. dial ##3424. press call. This should put the phone in DM mode.
iv. Win 7 will try to find the drivers and fail. If you open the device manager (or short cut just run devmgmt.msc), you should see the
2 devices with no drivers. HTC DIAG and HTC DIAG 9K.
v. double click on HTC Diag and click upgrade drivers. You need to manually upgrade the drivers..
http://forum.xda-developers.com/showthread.php?t=697487 This guide does a very good job. I dont want to repeat it. You can look at it if you are stuck. Just look at the driver installation part alone.
vi. Just ignore the HTC Diag 9k for now.
3. You have done a major step already. (I got stuck on step 2 for quiet sometime.). Install cdma workshop(CDMAWS). This software will trip anti-virus software(AV). So, just turn-off AV( or add CDMAWS in your AV's exclusion list). Apparently CDMAWS does use the virus technique to work but it is not malicious.
i. connect the phone to PC and dial ##3424 for DM mode. Find out which COM port your phone is using to connect.
ii. start CDMAWS. Select the COM port you phone uses. click connect. These should be in the topline of the GUI.
iii. if you are connected. The status bar at the bottom of window should indicate it. If everything is fine, click read(it should be next to connect/disconnect button). If everything is working so far, lots of empty spaces will be populated with data.
iv. switch to the Security tab. look for a spc button. enter "000000" in the text box above it(dont include quotes). This is the password for EPST. click spc -> spc send. you should see a pop-up saying phone unlocked. (if you are using this guide for Sprint phones, you need to obtain this password). Verizon just leaves it unlocked.
v. goto 'other' tab. look for RU-IM. click on the drop-down box. Select "NV-only". This option will be present only in full version.
vi. if you have not downloaded the attachment on this post, do it now. Now focus your attention on PRL box in the same tab as in step v.
PRL stands for preferred raoming list. I have attached 2 prl files. For me the 51720-evdo.prl gave roaming sign. I used 52711.prl, it worked fine. Click on write and choose 52711.prl from you download directory. It should write, the information to your phone.
vii. next switch to NAM tab. Enter the MIN you got from the email you got from kitty wireless (link is provided above). You can also get that info from pageplus by calling. MDN is nothing but your cell number. Enter that in dir or directory text box. click write.
4. you are done with CDMAWS. you can reboot your phone. At this point, if you havent changed ESN with pageplus do so now. You can do ESN change through online chat at pageplus website. It is free.
5. If you see roaming sign on your rezound, you need to use a different PRL. Roaming is indicated by a small triangle above the signal bars. start CDMAWS and select a different PRL file to write to your phone(steps 3(i) - 3(vi)). If everything is fine, from you rezound, call *22890 to program your phone. You can also use *22801 to program. if after a short pause it says unable to program your phone. It failed to program. Make sure you followed all the steps. If after a long pause it says unable to program. you have succeeded in getting the phone registered with pageplus. Now you should have your phone working for Voice and SMS/texting.
6. Take a deep breath and pat yourself, you have achieved a major step. Now to program 3g part. As i said before, if you are having locked stock ICS rom, you wont be able to go further. ICS doesn't let changing APNs. GB is fine with changing APNs. I havent rooted my ICS. i am just happy with a working Voice and SMS for my needs. Wifi satisfies my need.
7. Fire up QPST configuration.
i. Click on "Add New Port..." Select the port your device is on. It should be same as in CDMAWS.
ii. On the next screen highlight your device.
iii. Click on "Start Clients--Service Programming"
iv. Click 'Read From phone" When the prompt pops up click "OK"
v. Now tab over to "M.IP"
vi. In the drop down below that says simple ip+Mobi change that to "Simple IP"
vii. Now double click on "Profile 2"
viii.In the "NAI" section put your phone [email protected]
ix. In the "tetheredNAI" section put your phone [email protected]
x. For the IP Address put 255 all the way across for the last two sections and leave the 0's in the first section and Click OK
xi. Now click on "PPP config"
xii. Click "Um"
xiii. In the box that says "User ID", Enter your phone [email protected]
xiv. Click in the box that says "Tethered NAI", Enter your phone [email protected]
xv. Click in the box that says "Password", Enter "vzw"
xvi. Click the "AN" tab, User ID is your phone [email protected] and Password is "vzw"
xvii. Click "write to phone"
8. Power your phone down then reboot it.
9. i. Connect to wifi
ii. Open market
iii. Search for "APN Backup and Restore" and install. If you have GB, this will work on it own. Now if you have a rooted ICS, you can use Titanium Backup pro to run this system app. ICS allows system apps to modify APNs.
iv. Open APN and click Backup APN's
v. Now put your phone in "airplane mode"
vi. Click "delete apn's"
vii. Click "restore apn"
viii. Select page plus apn from below
ix. Disable Airplane Mode
x. Reboot
And thats it your fully flashed with MMS, Talk, Text, 3G
Credit goes to lots of folks. Mainly to Nevell, techwerkz, folks at howard forums and scores of others who are not mentioned.
Hope this helps a few folks.
Great guide.
hey guys, im kinda new to this and im planning to switch from VM to PP. I am plannng to buy the HTC Rezound. When i buy it, do i have to buy the contract version or the "month to month" version on the verizon site?? And does this tutorial actually work? Can anyone confirm it? And i dont care about 3g or 4g so i just want talk and text/
vwade79 said:
hey guys, im kinda new to this and im planning to switch from VM to PP. I am plannng to buy the HTC Rezound. When i buy it, do i have to buy the contract version or the "month to month" version on the verizon site?? And does this tutorial actually work? Can anyone confirm it? And i dont care about 3g or 4g so i just want talk and text/
Click to expand...
Click to collapse
Im thinking of selling mine soon. PM me if your interested.
Sent from my Nexus 7 using Tapatalk 2
I got 3G data working on stock ICS 4.0.3.605.1
To make it work you need to write all necessary settings to the 9K port as well. The tricky part is that QPST will not work and you have to use full paid version of CDMA Workshop or DFS (free version is ok) instead.
Repeat steps 3 and 4 of javamaan's guide for port 9k and use DFS for step 7.
Go to Programming/Data. Fill all fields in PAP, PPP, HDR AN, HDR AN Long and HDR AN PPP boxes. Set HDR SCP force AT config to RevA_MFPA. Uncheck eHRPD enabled. Go to Mobile IP and set NAI to [email protected].
When writing, make sure that it actually writes the data. Enable full logging and see if green "nv item written ok" messages appear. Ignore offline-d errors.
For more detailed instructions, see this cricket flashing guide.
You also need to have any sim card inserted to enable Mobile network Off/On switch in settings and get rid of the annoying message on the lock screen.
APN settings have no effect in CDMA mode. I've never touched APN menu and data works just fine.
The only thing it might be necessary is MMS, but I've never bothered to set it up.
Hello all,
For the life of me, I can't get sms or 3g to work. I've gone over this tutorial over and backwards and even did the cricket tut.
My rezound is on GB. I downgraded it with the official, stock, OTA or what ever you want to call it GB. I'm rooted but not custom ROM. I just got rid of the bloatware.
I have PPC service. Thanks, that part was great! There is a "write" line missing in the RU IM part, but I figured it out. Voice and simple text work but no sms. I even copied my wife's apn from her cell, but still, no go.
OK, done with my rant. Just had to let it out. So my steps:
in QPST - wrote everything to 8K as stated above, to the "t"
-I did come up with an error, but checked it in DFS and everything was there.
in DFS - wrote everything to 9k as stated above, to the "t"
Found the apn file from another thread because it is missing in this one. Did a restore, and.....nothing.
Found the apn settings from another site and entered it in manually......nothing.
Copied my wife's apn settings...nothing.
Made myself a drink...at least I have a good buzz going...check my phone...nothing...DOHHH!
What do I do now???
Cheers!
AsianCajun said:
Hello all,
For the life of me, I can't get sms or 3g to work.
Click to expand...
Click to collapse
As already mentioned above, forget about the APNs! They are not used for CDMA mode (except MMS). Until you have 3G data, just leave the default VZWINTERNET APN as it is.
You don't need to downgrade to GingerBread. I've done everything on ICS 4.0.3.605.1, but 4.0.3.605.2 should work as well.
Make sure you've actually written everything to both ports. Especially 9K port. Read back and check if all values are there (except passwords that can't be read). Read PRL and make sure that version is 51720.
Post your screenshots of DFS after you read the data (NAM/PRL, Data and MobileIP pages).
OK, I wrote the prl over again and opened up DFS and wrote to nam1 and nam2.
Well, I was able to get it to work. I put ics back on, updated to one of the newer prl's and put a sim chip. I'm not sure what did the trick, but my bet is on the chip. note* I used an old at&t sim chip that I had laying around. I still get the warning on the lock scene, but that doesn't bother me. Thanks again to those who made these tuts.
Cheers
Im getting close to getting my Rez up on PP,... (deleted)
EDIT: Thanks so much for this thread, Im well on my way, with a few bumps along the way while I learn the software and phone. was stuck at step 5 til I realized you did the programming and dont need the #22890. with or w/o my new sim, I can make & receive calls/texts. Im barred from the ota programming by the phone.
Now I'm figuring out qpst as to why it doesnt show profile 2, just a single profile (0). So I dont know if I should modify that profile 0... And I need to get rid of the error message re the 4g activation. So i'm a little ways from having any data functioning... going to bed, sleepy and cross-eyed...
"Activating your phone..."
In the lock screen, how do you remove the irritating "Activating your phone..." message. I have everything working except MMS, but I don't care about it, I just want the stupid notification gone.
I also have an LTE card installed. I had remotesquaD flash it for me...
HTC Rezound on PagePlus no 3G data
javamaan said:
Ok folks. If you are like me, you searched all over the web didnt find a definitive answer on how to go about getting your HTC rezound to Pageplus.
I bought a used Rezound. It came with NO Verizon SIM card. No software updates to it. I read a lot, sounded like getting to the latest stock was a good idea as it usually fixes issues. Well, I promptly updated to the leaked global ICS rom. Go the rom from android police dated Aug 15.
So my rezound had locked stock global ICS rom, no SIM card. Here is how i flashed it to pageplus. Please follow the steps as mentioned, as i have stumbled too many times and got it working.
================================
Not a must but...
1. Dont upgrade your phone to ICS rom if you dont want to root your phone. As ICS blocks APN updates. Meaning if you need 3g on pageplus or any other carrier and you dont want to root your phone, dont upgrade. If you dont mind rooting your phone, you can just ignore this warning.
Requirements:
MIN and MDN Information:
You can get MIN and MDN by calling pageplus or follow steps below.
goto http://www.kittywireless.com/pageplus/phonestatusform.html
right at the bottom you can enter email and phone number. You will get an email with MIN and MDN information.
OS Requirement:
Windows 7 64bit or 32bit. No support for Linux, Mac or XP(??).
Software you will need:
1. HTC Sync http://www.htc.com/us/support/htc-rezound-verizon/software-updates.
2. HTC Diag drivers. You can download from below.
3. QPST. http://conflipper.com/Software/QPST_2.7_366.rar
4. CDMA Workshop. You need the full version. Demo is not useful. There is an old 2.7 cracked version floating around in the web. That will do the job.
Steps to follow:
1. Install HTC Sync. This software will install HTC Sync and HTC Drivers. All you are looking for is HTC Drivers. So, as soon as installation is complete you can uninstall HTC Sync alone. They have seperate uninstallers.
2. Install HTC Diag drivers. Now, i hope you have access to Windows 7. These drivers didnt install in XP for me. it could work for you.
This step is crucial, without these drivers installed you wont be able to do anything.
i. Connect your phone to PC.
ii. Just leave it on charge mode. The HTC drivers you installed in previous step should recognize the phone.
iii. Goto the dialer in phone. dial ##3424. press call. This should put the phone in DM mode.
iv. Win 7 will try to find the drivers and fail. If you open the device manager (or short cut just run devmgmt.msc), you should see the
2 devices with no drivers. HTC DIAG and HTC DIAG 9K.
v. double click on HTC Diag and click upgrade drivers. You need to manually upgrade the drivers..
http://forum.xda-developers.com/showthread.php?t=697487 This guide does a very good job. I dont want to repeat it. You can look at it if you are stuck. Just look at the driver installation part alone.
vi. Just ignore the HTC Diag 9k for now.
3. You have done a major step already. (I got stuck on step 2 for quiet sometime.). Install cdma workshop(CDMAWS). This software will trip anti-virus software(AV). So, just turn-off AV( or add CDMAWS in your AV's exclusion list). Apparently CDMAWS does use the virus technique to work but it is not malicious.
i. connect the phone to PC and dial ##3424 for DM mode. Find out which COM port your phone is using to connect.
ii. start CDMAWS. Select the COM port you phone uses. click connect. These should be in the topline of the GUI.
iii. if you are connected. The status bar at the bottom of window should indicate it. If everything is fine, click read(it should be next to connect/disconnect button). If everything is working so far, lots of empty spaces will be populated with data.
iv. switch to the Security tab. look for a spc button. enter "000000" in the text box above it(dont include quotes). This is the password for EPST. click spc -> spc send. you should see a pop-up saying phone unlocked. (if you are using this guide for Sprint phones, you need to obtain this password). Verizon just leaves it unlocked.
v. goto 'other' tab. look for RU-IM. click on the drop-down box. Select "NV-only". This option will be present only in full version.
vi. if you have not downloaded the attachment on this post, do it now. Now focus your attention on PRL box in the same tab as in step v.
PRL stands for preferred raoming list. I have attached 2 prl files. For me the 51720-evdo.prl gave roaming sign. I used 52711.prl, it worked fine. Click on write and choose 52711.prl from you download directory. It should write, the information to your phone.
vii. next switch to NAM tab. Enter the MIN you got from the email you got from kitty wireless (link is provided above). You can also get that info from pageplus by calling. MDN is nothing but your cell number. Enter that in dir or directory text box. click write.
4. you are done with CDMAWS. you can reboot your phone. At this point, if you havent changed ESN with pageplus do so now. You can do ESN change through online chat at pageplus website. It is free.
5. If you see roaming sign on your rezound, you need to use a different PRL. Roaming is indicated by a small triangle above the signal bars. start CDMAWS and select a different PRL file to write to your phone(steps 3(i) - 3(vi)). If everything is fine, from you rezound, call *22890 to program your phone. You can also use *22801 to program. if after a short pause it says unable to program your phone. It failed to program. Make sure you followed all the steps. If after a long pause it says unable to program. you have succeeded in getting the phone registered with pageplus. Now you should have your phone working for Voice and SMS/texting.
6. Take a deep breath and pat yourself, you have achieved a major step. Now to program 3g part. As i said before, if you are having locked stock ICS rom, you wont be able to go further. ICS doesn't let changing APNs. GB is fine with changing APNs. I havent rooted my ICS. i am just happy with a working Voice and SMS for my needs. Wifi satisfies my need.
7. Fire up QPST configuration.
i. Click on "Add New Port..." Select the port your device is on. It should be same as in CDMAWS.
ii. On the next screen highlight your device.
iii. Click on "Start Clients--Service Programming"
iv. Click 'Read From phone" When the prompt pops up click "OK"
v. Now tab over to "M.IP"
vi. In the drop down below that says simple ip+Mobi change that to "Simple IP"
vii. Now double click on "Profile 2"
viii.In the "NAI" section put your phone [email protected]
ix. In the "tetheredNAI" section put your phone [email protected]
x. For the IP Address put 255 all the way across for the last two sections and leave the 0's in the first section and Click OK
xi. Now click on "PPP config"
xii. Click "Um"
xiii. In the box that says "User ID", Enter your phone [email protected]
xiv. Click in the box that says "Tethered NAI", Enter your phone [email protected]
xv. Click in the box that says "Password", Enter "vzw"
xvi. Click the "AN" tab, User ID is your phone [email protected] and Password is "vzw"
xvii. Click "write to phone"
8. Power your phone down then reboot it.
9. i. Connect to wifi
ii. Open market
iii. Search for "APN Backup and Restore" and install. If you have GB, this will work on it own. Now if you have a rooted ICS, you can use Titanium Backup pro to run this system app. ICS allows system apps to modify APNs.
iv. Open APN and click Backup APN's
v. Now put your phone in "airplane mode"
vi. Click "delete apn's"
vii. Click "restore apn"
viii. Select page plus apn from below
ix. Disable Airplane Mode
x. Reboot
And thats it your fully flashed with MMS, Talk, Text, 3G
Credit goes to lots of folks. Mainly to Nevell, techwerkz, folks at howard forums and scores of others who are not mentioned.
Hope this helps a few folks.
Click to expand...
Click to collapse
Hello everyone, I am new to this forum and first thing I want to do is thank everyone for their time and effort of putting the useful information on this forum! Also thanks to javamaan, I have been able to activate my HTC Rezound (previously on Verizon) on PagePlus. I have the following working: Talk, TXT, MMS, and 1X data. But no matter what I do, (spent over a week on this now, no kidding) I can't get 3G working.
I have the original Verizon 4GLTE sim card installed.
I am S-OFF, rooted, running leaked android 4.0.3 (4.03.605.3). (QPST is only good for 8K port)
I use mostly CDMAWS 3.8.7 demo and DFS 4.0.0.5 to manipulate data.
I write same data values to 8K and 9K ports, to NAM1 and NAM2.
Could it have something to do with HA and AAA shared secret values? some say leave it blank, some say 'vzw' (in hex), some say need to get those off of a donor phone.....
Could it be that when writing any passwords in DFS for 9K port they don't seem to showup/stick?
Thank you!
-snpiee
Wileyworld said:
Im getting close to getting my Rez up on PP, but am stuck on (step 5) since I cant dial out to program phone
Click to expand...
Click to collapse
I never could get *228xx activation to work. Just filled all data manually.
You can try to insert some other sim card, like AT&T or whatever. It just wants to have something in the slot.
@ Wileywold:
Step 5 is just if you get the triangle by the signal bars. *228 in any form will give you that error. I followed yura's directions and programmed for the mms and 3g using DFS.
@ snpiee:
On my phone HA is 300 and AAA is 2. Like you, I don't know if that has anything to do with programming or not. I've tried different prls and still can't get 3g to show up. I'm also stuck on 1x.
snpiee said:
Could it have something to do with HA and AAA shared secret values? some say leave it blank, some say 'vzw' (in hex), some say need to get those off of a donor phone.....
Click to expand...
Click to collapse
You definitely don't need a donor phone. As I recall, I did "vzw". Actually, all that Mobile IP NAI stuff is not used if "Simple IP only" is selected.
Also, someone suggested to do a software reset with 4G SIM inside after writing all values. Not sure if it really helps, but you can try.
snpiee said:
Could it be that when writing any passwords in DFS for 9K port they don't seem to showup/stick?
Click to expand...
Click to collapse
Passwords don't show up when I read back after writing, so this is OK.
Check PRL version and other stuff.
---------- Post added at 10:10 PM ---------- Previous post was at 09:59 PM ----------
AsianCajun said:
I've tried different prls and still can't get 3g to show up. I'm also stuck on 1x.
Click to expand...
Click to collapse
Oh, I thought you finally got 3G... I will go make my DFS screenshots now, so we can compare.
I just updated my prl to 52874 hoping it would point my Rez to 3g towers. Well, I'm still on 1x.
Screenshots of 9K port. I've highlighted some important items.
I finally got it. I wrote to both 8K and 9K ports and NAM1 and NAM2. All values were the same. My prl is the most recent verizon from my area, which is 52874. Here are the screen shots.
Thanks again to yura and javamaan for their hard work!
AsianCajun said:
I finally got it. I wrote to both 8K and 9K ports and NAM1 and NAM2. All values were the same. My prl is the most recent verizon from my area, which is 52874. Here are the screen shots.
Thanks again to yura and javamaan for their hard work!
Click to expand...
Click to collapse
You got 3G working now? I will compare your values to mine when I get home today....
Thanks for posting DFS screenshots!
By the way in your pics you use PrefMobileIP not SimpleIP is that correct?
Yura80 said: "Screenshots of 9K port. I've highlighted some important items."
Thanks for kindly sharing help here! I continue to tinker with this by lurking here and (after success with voice/texts/1x data) I'm now working on getting the 3g operating, and the dfs screen shots are very helpful. I want to upload a few for someone to see, and point me closer to my goal. Ive tried to imitate yours, but im running dfs 3.1.xxx and there are a few differences in the location of items, and labeled a bit different. I had to guess at one of the places to insert the dun info since it didnt show quite the same layout of lines/descriptions.For example, PAP has an extra line called data, while the PPP section has 1 less line , so I tried the dun line in that PAP section.
I'm very close to having this thing DONE and I never would have gotten here without great tutors right here!
BTW, What do you use to get the great screen shots to insert here in the forum?
I tried updating the PRL to one of the verizon hacked ones with CDMA Workshop. It succeeded, according to it, but now I have no service, not on sprint nor any other network. I can try and flash apparently any PRLs (have tried 11115, 11119, 12121, 12123, 24004, 60686, 60687, 60690 currently on this). I've tried flashing different roms altogether, and no difference - CM didn't work, currently on MeanRom. Most of the ## codes don't work, come up really slow, like 1-2 minutes, and the ones that ask for the MSL say it's the wrong password. MSL reader and cdma workshop both confirmed it's the right one. I've tried flashing two different radios via TWRP and while the update was successful, still no data. The phone is rooted, has TWRP 2.3.1.0, S-ON
HBOOT - 1.19.0000
Radio 1.12.11.0809
It seems to me that the radio go somehow bricked by CDMA Workshop. Anything else I can try? Are there any complete, stock-like roms (or non-stock, don't really care at this point) that will wipe/upgrade radio, PRI, etc all over again, even if I have to reprovision it? I have a feeling from the unresponsiveness of the radio it's pointless to try and reprovision it now with sprint.
The other weird thing, under monitor tab in CDMA Workshop, I can see it try to come up but going blank, maybe every 7-10 seconds... it clearly doesn't like something.
Need help before I have to activate my old samsung epic, that phone is like a bad std, it just won't go away.
S-on phones don't have direct access to boot or misc partitions. Unless you have hboot 1.12, I don't see you updating the radios through twrp or otherwise. Since I'm not very familiar with CDMA workshop I can't offer much advice. Try forcing a hands free activation. From the dialer type ##786#. Select menu, reset and enter msl. This will force a reset of your os. Maybe someone more knowledgeable can help.
Gotcha - on the S-on stuff... actually working on getting a USB ubuntu drive going now. ##786# comes up very slow, if it comes up at all, and then tells me the password isn't good. How do you flash stuff with the bootloader after I get it to be S-OFF, just put the files in the root of the internal storage, /sdcard? Then reboot to bootloader and?
Updates to firmware should be named PJ75IMG.zip. Place it on external and boot to bootloader. It will look for update files to install and reboot after.
If you are running dirty racun don't use a flash drive, burn it to cd or dvd
Thanks for the tip on the usb vs cd thing. I've gotten to the last step on this list: http://unlimited.io/jewel.htm , but something's going wrong and I can't tell what. I got it to the very last step, got past the reboots, got this:
Code:
Racun is sneaking...
It's a long way to sneak this will take several minutes...
Hiding behind a wall..
Checking for competition...
Checking for predators...
Sneaking around the dog house...
Quit...
Rebooted into bootloader, and it's still S-ON. Tried it again, from the sudo ./RabiesShot command, same thing. Ideas?
Try a different usb, make sure it's usb 2.0 and not 3 or 1. Make sure sd has enough space and read/write access is fast enough
it's an older core2duo box I got from work that I was gonna put in the garage. It should be usb 2.0, it's too new to be 1.0 and too old to be 3.0... as for the card, I had a 16gb in, I can put my normal 64gb good card in, but it asked for 2-16gb... Would keeping trying multiple times make a difference or is it the same every time?
What live distribution are you running?
12.04 32 bit.
Was that an actual failure message, is there supposed to be more goofing around or?
I would check with unlimited on irc, it's listed on their site
I got it working - got the S-OFF installed succesfully - had to reformat the sd card in a computer for some reason, and the 2nd time around it worked fine. When the phone came back up it also reactivated itself and updated its own PRL, data and 3g work now. I think I'm done trying to change the PRL for a few days...