Related
I've been (at least trying to) patiently wait for Deck to post full install instructions for CM10 but the CM10 op is still bare as bones. Has anyone else posted an install guide or instructions yet?
I'm currently rooted with RegawMod and running MeanRom 2.1 and it's really terribly laggy and frustrating, I can't wait any longer for CM10. Do I need S-off to install CM10 or do I just wipe, flash, and go?
Thanks for any help or links!
If you are on hboot 1.15 or higher you have to fast boot flash the kernel.
Other than that its just like a normal aosp install. Wipe flash rom flash gapps.
Its been my daily for 3 weeks.
Sent from my EVO using Tapatalk 2
You don't need s-off. You will however have to flash the boot IMG separately by using fastboot or the app flash image GUI and a full wipe is definitely required. There is a helpful thread in Q&A called "don't panic" that will answer all your questions
Good luck
Sent from my EVO using xda app-developers app
corcgaigh said:
You don't need s-off. You will however have to flash the boot IMG separately by using fastboot or the app flash image GUI and a full wipe is definitely required. There is a helpful thread in Q&A called "don't panic" that will answer all your questions
Good luck
Click to expand...
Click to collapse
Dont use flash image gui unless you know how to do it manually through fastboot. You are just asking for issues
Instructions:
http://androidforums.com/evo-4g-lte-all-things-root/606748-how-install-kernels-h-boot-1-15-a.html
Rxpert said:
If you are on hboot 1.15 or higher you have to fast boot flash the kernel.
Other than that its just like a normal aosp install. Wipe flash rom flash gapps.
Click to expand...
Click to collapse
I'm on hboot 1.12, so does that mean I can just flash normally?
edit - From what I can tell from reading, hboot 1.12 doesn't have the same restrictions that 1.15+ do, so I think I'm OK but I would like verification.
Thanks for the help everyone.
Yes hboot 1.12 allows for access to the boot partition
Also luuuuucckkyyyyyy...
EdhyMonker said:
I'm on hboot 1.12, so does that mean I can just flash normally?
edit - From what I can tell from reading, hboot 1.12 doesn't have the same restrictions that 1.15+ do, so I think I'm OK but I would like verification.
Thanks for the help everyone.
Click to expand...
Click to collapse
If you are on Hboot 1.12 I'd strongly suggest looking into getting S-OFF. Theres really no reason not to.
Up to you though, its not required
Bit off topic, anyone check to see if you can push a new splash, right now I'm too lazy to start my PC just to fastboot one measly splash
Rxpert said:
If you are on Hboot 1.12 I'd strongly suggest looking into getting S-OFF. Theres really no reason not to.
Up to you though, its not required
Click to expand...
Click to collapse
The S-OFF guide was way over my head so I just let it be. If there's not a real good reason for doing it, and I can still run CM10, then I'd rather not.
It allows you to directly flash new firmware like radios to fix any problems a device might be having. If you have Son and want the latest firmware you have to revert back to stock and accept ota, then unlock reflash recovery and reflash custom ROM or rooted stock, you could also just flash root installer if you want to just root stock
om4 said:
It allows you to directly flash new firmware like radios to fix any problems a device might be having. If you have Son and want the latest firmware you have to revert back to stock and accept ota, then unlock reflash recovery and reflash custom ROM or rooted stock, you could also just flash root installer if you want to just root stock
Click to expand...
Click to collapse
No, S-ON people with 1.12 H-boot can flash radios and firmware from recovery. They can do whatever they please in recovery just like S-OFF. S-OFF users can flash things from bootloader and even change the appearance of their h-boot to read S-ON and **locked** even though they are S-OFF
To the OP, this is the best rooting guide I've seen. It really explains everything step by step. http://androidforums.com/evo-4g-lte...panda-s-htc-dev-ltevo-root-dummies-guide.html Its recommended to have Linux at least bootable, because in the small chance the phone gets bricked... the unbricker program requires linux.
I ran it in windows before the unbricker was available, no issues here
You basically just hook the phone up to it and run the program like you do for most other root programs. All 1-click
Ah yeah forgot to mention that, most everyone is on 1.15 or 1.19 sorry
om4 said:
Ah yeah forgot to mention that, most everyone is on 1.15 or 1.19 sorry
Click to expand...
Click to collapse
Alright, I got S-Off using Lazy Panda and it went better than expected!
Do I need to flash updated firmware / radios separately from CM10, or does CM10 include latest firmware?
Sorry to ask dumb questions, but I do hope this thread will also be a good resource for others like me.
You don't have to flash any firmware updates. There are a few users with issues although they may be related to the ROM update and not necessarily the firmware included. I haven't really checked since I'm s on. If you want to update the radios there's an update zip here somewhere, be sure to read through everything carefully. Radios are more risky then every day flashing
Alright everyone now I need some help!
I flashed CM10 after s-off, was on stocked 1.13 rooted rom.
Now when CM10 boots up I am faced with a phone activation screen. It says something like "you will not be able to place calls or access the mobile network until the device is activated". I am unable to make calls or receive calls or access the internet. I have tried reflashing cm10 and the problem persists.
In the mean time, I will try flashing a nand backup and see where that gets me. I appreciate any and all help, and I have found no posts in the CM10 thread with a similar issue.
Update: I wiped and restored a back-up, MeanRom 2.1. Upon boot, hands-free activation ran and activated the phone and downloaded a PRL update. Everything is working fine now. Not sure if I should try CM10 again or what? Any advice?
EdhyMonker said:
Alright everyone now I need some help!
I flashed CM10 after s-off, was on stocked 1.13 rooted rom.
Now when CM10 boots up I am faced with a phone activation screen. It says something like "you will not be able to place calls or access the mobile network until the device is activated". I am unable to make calls or receive calls or access the internet. I have tried reflashing cm10 and the problem persists.
In the mean time, I will try flashing a nand backup and see where that gets me. I appreciate any and all help, and I have found no posts in the CM10 thread with a similar issue.
Update: I wiped and restored a back-up, MeanRom 2.1. Upon boot, hands-free activation ran and activated the phone and downloaded a PRL update. Everything is working fine now. Not sure if I should try CM10 again or what? Any advice?
Click to expand...
Click to collapse
ive only ever seen this issue with cyanogenmod and the old htc vogues, still great phones for what they were
EdhyMonker said:
Alright, I got S-Off using Lazy Panda and it went better than expected!
Do I need to flash updated firmware / radios separately from CM10, or does CM10 include latest firmware?
Sorry to ask dumb questions, but I do hope this thread will also be a good resource for others like me.
Click to expand...
Click to collapse
Yes, you should be flashing the upgraded firmware. You'll see the full firmware as the very first downloadable link. Flash that
http://themikmik.com/showthread.php...dio-Collection&p=220556&viewfull=1#post220556
Rename the file to "PJ75IMG.zip", place on root of SD card, and boot into HBOOT to flash. Check the md5 to make sure its right. With radios you want to make sure its the correct file.
Welcome to S-OFF my friend
Rxpert said:
Yes, you should be flashing the upgraded firmware. You'll see the full firmware as the very first downloadable link. Flash that
http://themikmik.com/showthread.php...dio-Collection&p=220556&viewfull=1#post220556
Rename the file to "PJ75IMG.zip", place on root of SD card, and boot into HBOOT to flash. Check the md5 to make sure its right. With radios you want to make sure its the correct file.
Welcome to S-OFF my friend
Click to expand...
Click to collapse
Thanks, but I tried this and it says "no image or wrong image" when trying to flash the PJ75IMG.zip file.
Did you type in PJ75IMG.zip or PJ75IMG and kept it a zip file...you should do the 2nd.
joebarkho said:
Did you type in PJ75IMG.zip or PJ75IMG and kept it a zip file...you should do the 2nd.
Click to expand...
Click to collapse
I thought that might've been the issue so I tried it both ways, didn't work either way. I'll take another shot at it tomorrow.
Hey everyone,
So I have successfully HTC Unlocked my Rezound bootloader, installed Amon Ra, and then installed and booted the CM9 unofficial. Problem was that CM9 wasn't quite as cooperative as I'd hoped - it is unofficial, after all, and so I decided to abandon that in favor of Nils' Business ROM. Here's where I ran into issues.
I have tried everything in every order I can find online and think of, including Nils' writeup. So, for the life of me, I cannot get the leaked ICS RUU to boot (4.03.605.2 as listed in his instructions on XDA). Install runs fine every time I do it from the relocked (I checked) stock HBOOT, all steps included. Every time it reboots (and I've tried forcing it back into hboot to do the install a second time) it just goes to the white HTC screen and starts boot looping. Tried it a million ways, no go. Also worth noting - the stock recovery doesn't install properly, either. Some'fin is hinky, here.
So I've tried just "assuming" it went fine anyhow and then proceeding with the install for Nils' ROM and same deal, no go, although with one difference. With Nils' ROM, it does display the boot splash screen "Nils Business ROM" or what have you about 1 out of every 4 "boots" in the loop cycle, and then reboots again.
I think I am going to perform S-OFF tomorrow if I have the time, and then try it again using the S-OFF instructions, but I would sincerely appreciate any help from you all. Honestly, I'm at near wit's end with this device, and I don't want to be, I enjoy this chase too much, but I *really* want the reward at the end of it, lol.
Any help is deeply appreciated.
- Katie
Re: [Q]
I'm guessing because of the corrupted recovery, you have a bad download of the RUU. Try re downloading and check the md5 hash for a match. The ruu should reboot itself after the first pass and end up in bootloader again for the second pass.... If not then after the first pass just hold down power + vol down to get back to bootloader.
Hope this helps
Sent from my ADR6425LVW using xda app-developers app
Make sure that you have a booting ROM before you s-off. You will cause yourself all kinds of heartache if you don't.
Using an sd card reader on a pc, check md5 of your RUU zip file. If it checks out good, put the sd back in your rez and do an hboot power on and accept the update again. Report back with your findings. Also you will need to re-unlock your hboot after and install your recovery again.
Snuzzo said:
Using an sd card reader on a pc, check md5 of your RUU zip file. If it checks out good, put the sd back in your rez and do an hboot power on and accept the update again. Report back with your findings. Also you will need to re-unlock your hboot after and install your recovery again.
Click to expand...
Click to collapse
Hey, thanks. Yeah, the RUU does check out just fine against an MD5SUM.
nm.... just read your original post again and you say you did relock the phone. I was hoping it was something simple like that that was overlooked.
Carry on...
feralicious said:
Nothing to see here, folks, move along.
Click to expand...
Click to collapse
Right now, I cannot S-OFF because it requires a working stock image, and I'll be lucky to get anything more than CM9 unofficial working here.
You're too fast, now my bad post lives on...
So, when theh RUU failed, you unlocked again, flashed a custom recovery and tried to flash Nils' ROM?
Do you have a nandroid you can try to restore? Even if its the cm9 ROM at least to see if you can get it back to a working phone?
feralicious said:
You're too fast, now my bad post lives on...
So, when theh RUU failed, you unlocked again, flashed a custom recovery and tried to flash Nils' ROM?
Do you have a nandroid you can try to restore? Even if its the cm9 ROM at least to see if you can get it back to a working phone?
Click to expand...
Click to collapse
Well that's the trick. CM9 didn't work well enough to even be worth backing up. I'm trying to reinstall it again now just to see if I get there - and it looks like I will. Once I'm back up with that, I'm not sure where to go from there. The phone barely worked under CM9. Really hoping to get Nils' ROM on there, since it gives all the nice features of a stock device without the bloatware. Even if I never get S-OFF, I'll be perfectly happy with just Nils' software.
How about this... did you wipe everything before running the RUU? There's CleanWipe in the Development forum you can flash it from recovery and it will wipe everything 5 times!
This shouldn't make any difference, but there's also a different RUU, the OTA that's not global. You might try that one instead. I'm convinced that sometimes things are just voodoo even when they should be completely logical. That's definitely the case at work on the Avid systems I use.
Here's the link to it:
http://androidfiles.org/ruu/?dir=Vigor
feralicious said:
How about this... did you wipe everything before running the RUU? There's CleanWipe in the Development forum you can flash it from recovery and it will wipe everything 5 times!
This shouldn't make any difference, but there's also a different RUU, the OTA that's not global. You might try that one instead. I'm convinced that sometimes things are just voodoo even when they should be completely logical. That's definitely the case at work on the Avid systems I use.
Here's the link to it:
http://androidfiles.org/ruu/?dir=Vigor
Click to expand...
Click to collapse
I did try wiping everything first. No luck. I will try the CleanWipe tomorrow, because right now, whatever my issues are, I'm being prevented from solving them since I can't S-OFF and I can't even seem to get a working ROM to make the phone worth having! Ugh.
And you can try installing it under fastboot oem ruu instead of the ph.zip file
Sent from my HTC Rezound...
Flyhalf205 said:
And you can try installing it under fastboot oem ruu instead of the ph.zip file
Sent from my HTC Rezound...
Click to expand...
Click to collapse
Oh yeah! Try that. Someone else was having trouble and did it that way and it worked. Here's instructions, just make sure you use PH98IMG and not whatever is used in the instructions since it was written up for a different phone.
http://androidforums.com/incredible-all-things-root/487280-easier-way-flash-pb31img-files.html
Also, once you get your phone back to stock make a nandroid as soon as you flash the recovery again so you'll have that to go back to if you have any more issues.
Flyhalf205 said:
And you can try installing it under fastboot oem ruu instead of the ph.zip file
Sent from my HTC Rezound...
Click to expand...
Click to collapse
Thank you, your magnanimity! Seriously, lol, you're gracing my thread just by being here. :victory:
feralicious said:
Oh yeah! Try that. Someone else was having trouble and did it that way and it worked. Here's instructions, just make sure you use PH98IMG and not whatever is used in the instructions since it was written up for a different phone.
http://androidforums.com/incredible-all-things-root/487280-easier-way-flash-pb31img-files.html
Also, once you get your phone back to stock make a nandroid as soon as you flash the recovery again so you'll have that to go back to if you have any more issues.
Click to expand...
Click to collapse
Thanks for the clicky, Feralicious. Same results, unfortunately. I'm going to try doing the RUU flash of Nils' ROM instead. Do you guys know where I can get the ICS firmware by itself? I cannot be sure that it's actually flashed right, unfortunately.
Your HBOOT is 2.27 and it should say relocked????
It should since you flashed the 4.03.605.2 RUU. The only RUU you will be able to flash since your S-ON is the one found here http://www.androidfilehost.com/?fid=9390034591667978440
The other RUU will fail because you can't downgrade. So the link above(The Global RUU) will that fail or completely install 100%??
If it does install 100% and boot loops still. Take out the sdcard. Boot into the HBOOT and perform a factory reset inside of HBOOT/Fastboot(NOT IN RECOVERY)
Report your status
EDIT
The link listed above for the RUU. Other way of installing it which is a great way to look at the status of everything.
Boot into Fastboot
fastboot oem rebootRUU
fastboot oem lock
fastboot flash zip rezound_AndroidPolice_4.03.605.2_PH98IMG.zip
fastboot reboot
EDIT2:
If you can't get it installed or it did. Just go ahead and unlock again. Flash custom recovery. Install a rom. Flash the boot.img in fastboot. Factory reset. and then see if it boots. If still not working. hit me up on google chat [email protected]
Flyhalf205 said:
Your HBOOT is 2.27 and it should say relocked????
It should since you flashed the 4.03.605.2 RUU. The only RUU you will be able to flash since your S-ON is the one found here http://www.androidfilehost.com/?fid=9390034591667978440
The other RUU will fail because you can't downgrade. So the link above(The Global RUU) will that fail or completely install 100%??
If it does install 100% and boot loops still. Take out the sdcard. Boot into the HBOOT and perform a factory reset inside of HBOOT/Fastboot(NOT IN RECOVERY)
Report your status
EDIT
The link listed above for the RUU. Other way of installing it which is a great way to look at the status of everything.
Boot into Fastboot
fastboot oem rebootRUU
fastboot oem lock
fastboot flash zip rezound_AndroidPolice_4.03.605.2_PH98IMG.zip
fastboot reboot
EDIT2:
If you can't get it installed or it did. Just go ahead and unlock again. Flash custom recovery. Install a rom. Flash the boot.img in fastboot. Factory reset. and then see if it boots. If still not working. hit me up on google chat [email protected]
Click to expand...
Click to collapse
I'll do that stuff and let you know. Thank you!
Yes, I am on 2.27 HBOOT.
Point of interest, though possibly unsurprising. When I send the lock command, it locks and reboots, but says "Failed" in my command window screen. Sure this is probably normal since the phone might just reboot before responding to the computer, but possibly an issue.
I believe that is the image I tried before, but I'll do it again both ways to be certain and report back soon! :good:
ncc74656m said:
Yes, I am on 2.27 HBOOT.
Point of interest, though possibly unsurprising. When I send the lock command, it locks and reboots, but says "Failed" in my command window screen. Sure this is probably normal since the phone might just reboot before responding to the computer, but possibly an issue.
I believe that is the image I tried before, but I'll do it again both ways to be certain and report back soon! :good:
Click to expand...
Click to collapse
My DNA said something about failing when I locked it. But it locked just fine.
Since it is failing.
fastboot oem rebootRUU
fastboot oem lock ----if unlocked
fastboot flash zip rezound_AndroidPolice_4.03.605.2_PH98IMG.zip
fastboot reboot
Should work Maybe
Flyhalf205 said:
Your HBOOT is 2.27 and it should say relocked????
It should since you flashed the 4.03.605.2 RUU. The only RUU you will be able to flash since your S-ON is the one found here http://www.androidfilehost.com/?fid=9390034591667978440
The other RUU will fail because you can't downgrade. So the link above(The Global RUU) will that fail or completely install 100%??
If it does install 100% and boot loops still. Take out the sdcard. Boot into the HBOOT and perform a factory reset inside of HBOOT/Fastboot(NOT IN RECOVERY)
Report your status
Click to expand...
Click to collapse
Ok, so, this part including a factory reset got me to "HTC Quietly Brilliant" screen, but then it bootloops again. Tried factory resetting again to no avail. Trying the second part.
Flyhalf205 said:
EDIT
The link listed above for the RUU. Other way of installing it which is a great way to look at the status of everything.
Boot into Fastboot
fastboot oem rebootRUU
fastboot oem lock
fastboot flash zip rezound_AndroidPolice_4.03.605.2_PH98IMG.zip
fastboot reboot
Click to expand...
Click to collapse
Same thing as before unfortunately. :/ Performed a factory reset afterwards to be safe - no go. Everything shows OK though in both this and the above install. *shrug*
Flyhalf205 said:
EDIT2:
If you can't get it installed or it did. Just go ahead and unlock again. Flash custom recovery. Install a rom. Flash the boot.img in fastboot. Factory reset. and then see if it boots. If still not working. hit me up on google chat [email protected]
Click to expand...
Click to collapse
Proceeding with another attempt at installing CM9, I guess. Maybe the first one got hosed. If I get it booting in any form, I'll Nandroid it before trying anything else.
ncc74656m said:
Proceeding with another attempt at installing CM9, I guess. Maybe the first one got hosed. If I get it booting in any form, I'll Nandroid it before trying anything else.
Click to expand...
Click to collapse
I really wouldn't see why you would need a Sense rom to get s-off. I would imagine it would just need su and busybox installed. But nandroid then try a sense rom again. Make sure you flash the boot.img through fastboot
Hi,
I have a Sprint CDMA HTC EVO 3D. I tried root and get S-OFF for it. Unfortunately I failed and now the phone fail to boot.
Below is what I did from which you might be able to diagnose it and give me suggestions.
(1) The original status of mu phone is:
Stock rom, I never root it before.
HBOOT-1.58.0000
Android Version: 4.03
HTC Sense version: 3.6
Software version: 2.95.651.6.710RD
(2) My root procedures:
I followed this post: http://forum.xda-developers.com/showthread.php?t=1813818
I successfully unlocked phone with HTCDev, successfully Flashed 4EXT recovery, and successfully installed Superuser-3.1.3-arm-signed.zip. I also booted into sytem, everything worked well.
However I failed in next step of JuopunutBear's Wire Trick (S-OFF). When I ran ControlBear.exe, it finally hanged there.
Current status of my phone:
Unfortunately I did not make a backup to my original ROM, so there is no way to revert back by restoring backup.
Now the phone is in unlocked status, I was able to boot to HBOOT and also enter 4Ext recovery, however I am not able to boot into Android. If I try to boot into Android, it always hang at black screen.
I am able to boot to fastboot (USB) mode, I tried to flash some stock ROM (listed at http://forum.xda-developers.com/showpost.php?p=24268786&postcount=209), but I failed. For example, I ran a RUU of 2.89.exe, it detected my phone version is 2.95, and further update RUU failed.
Looks like my partition is ruined, but I might be wrong.
ANyone can help me to restore my phone to working status? At least I need the phone to be able to boo to Android.
Here are also some tries that I ever did:
(1) I ever put the PG86IMG.zip file (downloaded from http://forum.xda-developers.com/showpost.php?p=21593454&postcount=564) to my sdcard, still failed.
(2) I ever formatted all partition from 4EXT recovery
lsdyna said:
Here are also some tries that I ever did:
(1) I ever put the PG86IMG.zip file (downloaded from http://forum.xda-developers.com/showpost.php?p=21593454&postcount=564) to my sdcard, still failed.
(2) I ever formatted all partition from 4EXT recovery
Click to expand...
Click to collapse
EDIT:
Okay. I've got some questions.
1. You're stuck on some black screen as you said. It boots past the white HTC splash and then it's stuck on that black screen, right. Do you mean the juopunutbear "arrow screen" - juopunutbears boot.img?
2. I think if you had flashed the original boot img everything would have been fine.
3. The easiest way is to flash to stock, so lets try to figure out why it doesn't flash.
MrJyrks said:
Okay. So from what I understood, you are stuck on the black juopunutbear screen, right?
Click to expand...
Click to collapse
Yes, after I was stuck with black juopunutbear screen, I took battery out, reboot again, never was able to root to Android. I am only able to boot to HBoot.
lsdyna said:
Yes, after I was stuck with black juopunutbear screen, I took battery out, reboot again, never was able to root to Android. I am only able to boot to HBoot.
Click to expand...
Click to collapse
And you can boot to recovery, right?
EDIT:
One more thing. Which ruu were you trying to run
Edit2:
What's your CID? Use "fastboot getvar cid" or "fastboot oem readcid" (without quotes).
Edit3:
BTW, this was on the wire trick page... http://unlimited.io/jbtroubleshooting.htm - TROUBLESHOOTING There was everything you needed to know when you failed at something. Remember that page. You may need it the next time you try to do the wiretrick.
Q: Were you using a linux distro for the wire trick and did you use the appropriate files for wire trick since GB and ICS have separate tools?
If you want I may assist you in gaining s-off if we get this thing functional again.
Yes, I am able to boot to recovery.
I tried ROM's here
http://forum.xda-developers.com/showpost.php?p=24268786&postcount=209
and
http://forum.xda-developers.com/showthread.php?p=22519105#post22519105
I tried 2.17, 2.89, unfortunately none of them worked
My CID is SPCS_001
MrJyrks said:
And you can boot to recovery, right?
EDIT: One more thing. Which ruu were you trying to run
Edit2: What's your CID? Use "fastboot getvar cid" or "fastboot oem readcid" (without quotes).
Click to expand...
Click to collapse
lsdyna said:
Yes, I am able to boot to recovery.
I tried ROM's here
http://forum.xda-developers.com/showpost.php?p=24268786&postcount=209
and
http://forum.xda-developers.com/showthread.php?p=22519105#post22519105
I tried 2.17, 2.89, unfortunately none of them worked
My CID is SPCS_001
Click to expand...
Click to collapse
Aw man, I'm completely sorry I didn't see this: Software version: 2.95.651.6.710RD
That means, no RUU for you cause htc/sprint wasn't kind enough to provide the ruu. Also FYI you can't flash a ruu lower than your current one.
So your best bet is to flash the most stock 2.95 cdma rom you could find and right after, flash the stock cdma evo 3d kernel through fastboot or 4ext (I think 4ext smartflash does the same thing). Try to find something that's COMPLETELY STOCK - with no mods whatsoever or if you couldn't find any, try something that's almost* stock. That should get you booting and you can try s off again.
Edit: This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Now I only want to revert my phone to stock, not considering root at present time.
I searched 2.95 ROM, unfortunately the highest version that I can find is 2.89. Does this mean I have no way to revert my phone to live? Thanks a lot.
MrJyrks said:
Aw man, I'm completely sorry I didn't see this: Software version: 2.95.651.6.710RD
That means, no RUU for you cause htc/sprint wasn't kind enough to provide the ruu. Also FYI you can't flash a ruu lower than your current one.
So your best bet is to flash the most stock 2.95 cdma rom you could find and right after, flash the stock cdma evo 3d kernel through fastboot or 4ext (I think 4ext smartflash does the same thing). Try to find something that's COMPLETELY STOCK - with no mods whatsoever or if you couldn't find any, try something that's almost* stock. That should get you booting and you can try s off again.
Click to expand...
Click to collapse
I ever run a RUU 1.13...exe for mmy phone, it said my device is having 1.000, and it tried to update to 1.13. However, the update procedure always failed at some point, some at beginning, some failed at 'wring signature'...
MrJyrks said:
Aw man, I'm completely sorry I didn't see this: Software version: 2.95.651.6.710RD
That means, no RUU for you cause htc/sprint wasn't kind enough to provide the ruu. Also FYI you can't flash a ruu lower than your current one.
So your best bet is to flash the most stock 2.95 cdma rom you could find and right after, flash the stock cdma evo 3d kernel through fastboot or 4ext (I think 4ext smartflash does the same thing). Try to find something that's COMPLETELY STOCK - with no mods whatsoever or if you couldn't find any, try something that's almost* stock. That should get you booting and you can try s off again.
Click to expand...
Click to collapse
lsdyna said:
I ever run a RUU 1.13...exe for mmy phone, it said my device is having 1.000, and it tried to update to 1.13. However, the update procedure always failed at some point, some at beginning, some failed at 'wring signature'...
Click to expand...
Click to collapse
This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Flash like a normal rom and don't forget to flash the boot img because that's what's really causing you problems right now. I'd choose the deodexed one from there.
My HBoot screen shows below:
SHOOTER XC SHIP S-ON RL
HBOOT-1.58.000
RADIO-1.09.00.0108
OpenADSP-v02.6.0.2226.00.0217
DO you think I still have chance to save my device? Thanks a lot.
lsdyna said:
I ever run a RUU 1.13...exe for mmy phone, it said my device is having 1.000, and it tried to update to 1.13. However, the update procedure always failed at some point, some at beginning, some failed at 'wring signature'...
Click to expand...
Click to collapse
lsdyna said:
My HBoot screen shows below:
SHOOTER XC SHIP S-ON RL
HBOOT-1.58.000
RADIO-1.09.00.0108
OpenADSP-v02.6.0.2226.00.0217
DO you think I still have chance to save my device? Thanks a lot.
Click to expand...
Click to collapse
If you have access to the recovery, most likely, yes.
Hello MrJyrks,
Thank you so much for the link! I am eager to try that. Before I do that I think I shall ask two questions to avoid further mess up the device:
Question #1: To install the deodexed rom, which is the correct way:
(1) Rename the ZIP file to PG86IMG.ZIP, put to root of sdcard, then boot, letting the Bootloader to do the update.
(2) In 4EXT recovery, enable smartflash, enable script asserts, then install the zip from the root of sdcard.
Question #2: You said I shall flash boot image, can you tell me how to do this? I mean, where shall I get the boot image file? Flash it with 4EXT? SHall I do it before or after install ROM zip file?
Thank you very much for your helps!!!
MrJyrks said:
This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Flash like a normal rom and don't forget to flash the boot img because that's what's really causing you problems right now. I'd choose the deodexed one from there.
Click to expand...
Click to collapse
I tried install the stock ROM from your link (using 4EXT with smartflash enabled and script asserts enabled.) . Amazing that installation completed successfully (indeed this is the first ROM zip that I was able to install successfully since I mess up the device). When I exit After that, it did some further update which I guess is the boot.img that you mentioned.
4EXT it said 'a pending update for your boot partition is detected' and I think it was doing the boot image flash that you mentioned, right?
Unfortunately when I boo the device, I still got black screen.
Now I am unlocked and also rooted (since I successfully installed superuser in 4EXT). DO you think I shall lock the devioce before installing the stock ROM? If so, one possible issue is that if I relock the device, I found 4EXT is not available. In that case, how shall I install the ROM zip file?
Thanks.
MrJyrks said:
This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Flash like a normal rom and don't forget to flash the boot img because that's what's really causing you problems right now. I'd choose the deodexed one from there.
Click to expand...
Click to collapse
Further update:
I flashed boot image by: fastboot flash boot boot.img which is included in the stock ROM zip file.
The flash went successfully. However, I am still not able to boot to Android. WHat I have is the device hang there, alternatively displaying logo with white background, and black screen.
MrJyrks said:
This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Flash like a normal rom and don't forget to flash the boot img because that's what's really causing you problems right now. I'd choose the deodexed one from there.
Click to expand...
Click to collapse
I wiped cache and Dalvic, then re-flash the ROM, now I am able to boot as normal.
MrJyrks, you are my life save!!!
Your helps are sincerely appreciated !
lsdyna said:
I wiped cache and Dalvic, then re-flash the ROM, now I am able to boot as normal.
MrJyrks, you are my life save!!!
Your helps are sincerely appreciated !
Click to expand...
Click to collapse
You're welcome! I'm glad I could help!
---------- Post added at 12:02 PM ---------- Previous post was at 11:16 AM ----------
Oh, and if, in the future, you do try the wire trick and get stuck at some point you can revert the changes with ControlBear -r or ControlBear -f from command line. And you may also PM me if you need any help. Cheers!
MrJyrks, thank you so much!!!
MrJyrks said:
You're welcome! I'm glad I could help!
---------- Post added at 12:02 PM ---------- Previous post was at 11:16 AM ----------
Oh, and if, in the future, you do try the wire trick and get stuck at some point you can revert the changes with ControlBear -r or ControlBear -f from command line. And you may also PM me if you need any help. Cheers!
Click to expand...
Click to collapse
Similar problem, can't return to stock
I have a problem similar to lsdyna's, and am hoping that even though this post is old, MrJyrks or someone might be able to help me.
I am unsuccessfully trying to return my phone to stock. First a bit of history.
I had 2.95.651.6.710RD s-on hboot 1.58 Android Version: 4.03 HTC Sense version: 3.6 on my phone, and wanted root. I didn't need s-off, just wanted to root so could do some tweaking (stop some apps from autostarting, stop some form getting network access, etc.) so loaded 4EXT Recovery Touch, and got root (fastboot oem get_identifier_token method), got superuser in there, and happily began tweaking. Famous last words... I didn't make a backup right away (learned my lesson!) and suddenly found a 'overtweaked' sluggish phone on my hands.
Thought best thing would be to lose the root & return to stock & start over, carefully, making backups.
So I used Fastboot (fastboot oem lock) to lock it (worked) and proceeded to try to load RUU_Shooter_ICS_35_S_Sprint_WWE_2.89.651.2_Radio_1.09.00.0706__NV_NV_SPCS_1.43_release_271101_signed.exe into it [via my computer], but didn't realize until reading MrJyrks post that a lower RUU couldn't be used.
I now am relocked (phone does boot up, but can tell the system tweaks are still slogging it), lost the recovery, and wondering what to do... do I try putting recovery back in & using the Negalite 2.95 stock deodex ROM MrJyrks mentioned? If so, how do I use that zip file method verses the exe one I tried thru my computer?
Thanks for the help
You had issues with the RUU because your main version is higher than that contained in the RUU.
Unlock, flash recovery again. Boot into recovery and flash this zip: https://copy.com/wlVvwssXXNN00Pe
That will lower your main version. Relock the bootloader, put the phone into fastboot USB mode, then run the RUU while in fastboot USB mode.
Should be back to stock after that.
I installed CM using CWM onto my HTC Deluxe. I tried 4 different nightlies and the 10.2 stable and after installing any of them, I get this... it reboots into the white htc screen with a quick vibrate. Then it goes black for a second and reboots again. No CM screen or anything!
I've tried flashing it multiple times, doing factory resets, clearing cache and dalvaic cache. I am at a loss as to what to do next.
Oh and with the 10.2, instead of rebooting it just gets stuck at the HTC white screen!
If you unlocked the bootloader with htcdev.com and are still S-On, you need to flash the boot.img via fastboot. Common cause of your type of problems.
es0tericcha0s said:
If you unlocked the bootloader with htcdev.com and are still S-On, you need to flash the boot.img via fastboot. Common cause of your type of problems.
Click to expand...
Click to collapse
Well I looked and sure enough it is s-on. So I know the process of flashing an img with flashboot, but where can I aquire the correct boot.img? I am sure it needs to be a trusty source because I would imagine the boot image could really cause damage.
alexander7567 said:
Well I looked and sure enough it is s-on. So I know the process of flashing an img with flashboot, but where can I aquire the correct boot.img? I am sure it needs to be a trusty source because I would imagine the boot image could really cause damage.
Click to expand...
Click to collapse
You just need to extract it from whichever version of CMrom.zip you are trying to use.
es0tericcha0s said:
You just need to extract it from whichever version of CMrom.zip you are trying to use.
Click to expand...
Click to collapse
Okay cool! Easy enough. Question before I do this though... If I flash boot.img with fastboot, will this acheive soff? Neither rumrunner or Firewater works! And if I do this what will have have to do to go back to my stock Rom for any reason using CWM?
alexander7567 said:
Okay cool! Easy enough. Question before I do this though... If I flash boot.img with fastboot, will this acheive soff? Neither rumrunner or Firewater works! And if I do this what will have have to do to go back to my stock Rom for any reason using CWM?
Click to expand...
Click to collapse
No, this will not affect S-On/Off status. This is because the bootloader unlock provided by HTC is really only a partial one. It allows you to install custom roms, themes, mods, etc, but not to allow installation of a custom kernel through recovery. That's why you have to pull it from the rom and flash it separate. Once you do that, then it will behave like normal. You can also use an app like Flashify to install the boot.img, then boot to recovery and flash the rom, if you don't have access to a PC. Just make sure to do a nandroid BEFORE that, otherwise it will back up the new kernel you flashed on top of the older OS, so might not be compatible, especially when switching between stock and CM based things.
Please help. I have unlocked this phone through HTC Dev. I have flashed a custom recovery. Somewhere through this process, the original installation of the factory rom from VM was deleted. That doesn't bother me because I was never going back to it anyway, but If I had it right now, I wouldn't be here. I have tried to use the RUU exe in fastboot and the RUU zip in recovery from here. Neither will install, exe throws errors and the zip returns [bad]. I have also tried the [ROM] NegaLite-BluRom-JCFunk | 2.95 | Sprint/VM | Sense/Apex/Nova | 03/25/2014. This eventually installed, but will not boot even with installing boot.img separately. I followed all directions to the best of my ability, but by no means am I saying I did correctly, but I am pretty sure I did. So to recap - I have whats in the title, but no rom whatsoever installed that can be accessed. Any takers?
Some more info please, hboot version? Which recovery. s-on makes things harder.
To flash stock need to be relocked, stock will not flash from recovery.
If you put rom.zip, stock zip, in root of sdcard and rename to PG86IMG.zip. hboot will flash automaticly.
Or if you have a copy of the custom recovery img file on your computer, you can do a fastboot command that will let you boot from it and give it full write access.
fastboot boot recovery.img, then you can retry to flash negalite
img must be in directory you use fastboot in.
Philz recovery not working well for 3d, I use 4ext or my unofficial twrp.
Before I proceed in explaining anything, please let me Thank You JCFunk for lending me a hand in my endeavors. This is my first crack at a HTC device. So I'm a newb at locks, hboots, and HTC specifics. So, Thank You!
I scanned through a lot of information and I moved to quickly, thinking I would ace this project and not particularly following a guide step by step. I know I should just wire trick this phone. I am wanting to get to hboot 1.40 and use Revolutionary to S-OFF. Once that is achieved load a kitkat rom. This is just a project, not used for daily phone use - no service.
jcfunk said:
Some more info please, hboot version? Which recovery. s-on makes things harder.
To flash stock need to be relocked, stock will not flash from recovery.
If you put rom.zip, stock zip, in root of sdcard and rename to PG86IMG.zip. hboot will flash automaticly.
Click to expand...
Click to collapse
I tried this step first and it returned:
Main Version is older.
Update Fail!
Press <POWER> to reboot.
Would I be correct to say if I flashed the SetMainVersionLOW.zip that this method would likely work?
Also, if I am overcomplicating this(other than wire-trick) and there is an easier method, please advise.
oD33z said:
Before I proceed in explaining anything, please let me Thank You JCFunk for lending me a hand in my endeavors. This is my first crack at a HTC device. So I'm a newb at locks, hboots, and HTC specifics. So, Thank You!
I scanned through a lot of information and I moved to quickly, thinking I would ace this project and not particularly following a guide step by step. I know I should just wire trick this phone. I am wanting to get to hboot 1.40 and use Revolutionary to S-OFF. Once that is achieved load a kitkat rom. This is just a project, not used for daily phone use - no service.
I tried this step first and it returned:
Main Version is older.
Update Fail!
Press <POWER> to reboot.
Would I be correct to say if I flashed the SetMainVersionLOW.zip that this method would likely work?
Also, if I am overcomplicating this(other than wire-trick) and there is an easier method, please advise.
D33z
Click to expand...
Click to collapse
How good are you with linux, or do just use windows? Never did wire trick myself, I've always done Unknownforce hboot downgrade. Which I can now do in about 15 min.
s-off not required, there's many way to bypass unlocked limitations.
Your main var is to high because htc never released a current ruu, so the ota pushed version higher but no ruu to match.
what can I help you do?
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer
jcfunk said:
Philz recovery not working well for 3d, I use 4ext or my unofficial twrp.
Click to expand...
Click to collapse
Does your unofficial twrp support SELinux? I am assuming it does but just checking. Is it available for download and if so where?
oD33z said:
Does your unofficial twrp support SELinux? I am assuming it does but just checking. Is it available for download and if so where?
Click to expand...
Click to collapse
here's the thread
http://forum.xda-developers.com/showthread.php?t=2831444
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer
jcfunk said:
How good are you with linux, or do just use windows? Never did wire trick myself, I've always done Unknownforce hboot downgrade. Which I can now do in about 15 min.
s-off not required, there's many way to bypass unlocked limitations.
Your main var is to high because htc never released a current ruu, so the ota pushed version higher but no ruu to match.
what can I help you do?
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer
Click to expand...
Click to collapse
I am great with linux, but was under the assumption it needed to be burned to cd and that USB was not an option, please advise if not the case. I have read a ton and I remember reading about Unknownforce, but cant remember if thats the case or not.
Off topic: I learned from you that it has to be locked to go stock, but does it need to be unlocked to flash your rom or locked as well?
Unlocked for custom, locked for stock.
Here is unknownforce ultimate tool,
there was a live cd version made for windows users scared of linux.
I use tiny core linux for this, Ubuntu tries to mount all the partitions and you only have a 5 second window when they are writeable. I have used Ubuntu, at first, but preferred tinycore.
But first you are going to need to get stock.zip to install.
http://forum.xda-developers.com/showthread.php?t=1653777
I would do fastboot boot recovery.img
Then install negalite, so atless you can boot the phone
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer
---------- Post added at 12:37 AM ---------- Previous post was at 12:24 AM ----------
here is 4ext recovery I would use this one first until you get used to things, best recovery for 3d.
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer
Is 4ext > TWRP unofficial? I am currently on your unofficial TWRP and installing the latest negalite.
oD33z said:
Is 4ext > TWRP unofficial? I am currently on your unofficial TWRP and installing the latest negalite.
Click to expand...
Click to collapse
did you fastboot boot?
There are several custom recoveries out there.
Here is thread for 4ext
http://forum.xda-developers.com/showthread.php?t=1408936
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer
What I meant was, in your opinion, is the 4ext a better recovery than the unofficial TWRP?
During the install of Negalite at the point of -Setting Up Kernel Over-Clock Settings
under this it reads: assert failed: write_raw_image("/tmp/newboot.img","boot")
Is this a red flag of something not going right in any way?
After this I click Next>Recovery>Wipe Dalvik>Reboot and it boots into Fastboot. Whats happening at this point?
Since I am basically starting from scratch and the end goal is to have a kitkat rom and possibly S-OFF(if its a must to do so).
What all needs to be done as far as formatting, tweaks, or anything else to achieve the best performance, space, or anything you can think of?
Thats if you dont mind sharing. I appreciate your time and if I can be of service to you in any way, I will.
I am currently on the 4ext recovery with 1GB sd-ext 0 swap and formatted Ext4.
fastboot boot recovery.img
flashrom.zip from recovery
reboot, wipe dalvik, reboot
Negalite.zip installed with no errors whatsoever.
Thank You.
Beautiful smooth running rom btw.
Does all that above sound like I did the right things as for setting up and installing?
4ext is most stable, the unofficial has new features like f2fs and selinux, but 95% stable.
fastboot boot recovery.img is an old work around, also used to flash boot.img with fastboot. That is ok with roms that include a whole boot.img but roms like mine use a dynamic boot.img. Basically the installer makes the boot.img using your choices.
From what I know about Kitty kat I think you need to downgrade hboot or be s-off. Not sure I've stayed on ics for stability because I still use this phone. Also there is a new version of negalite on svn, just takes hours for me to upload a zip version.
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer
Revision 7
Are you sure this is the latest?
oD33z said:
Revision 7
Are you sure this is the latest?
Click to expand...
Click to collapse
Lol, yes since I updated it a few weeks ago
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer
I should have worded that different really, the revision numbers threw me, I honestly was just making sure I was in the right place. 48mb smaller, anything stripped?
jcfunk said:
Some more info please, hboot version? Which recovery. s-on makes things harder.
To flash stock need to be relocked, stock will not flash from recovery.
If you put rom.zip, stock zip, in root of sdcard and rename to PG86IMG.zip. hboot will flash automaticly.
Or if you have a copy of the custom recovery img file on your computer, you can do a fastboot command that will let you boot from it and give it full write access.
fastboot boot recovery.img, then you can retry to flash negalite
img must be in directory you use fastboot in.
Click to expand...
Click to collapse
I tried installing your new negalite the same way as I do the old version and at the end of the install procedure I get an error about set permissions. After that - reboot, wipe dalvik, reboot - it just reboots into recovery. I tried many times with SmartFlash enabled and disabled. I go back and install r121 with no problems.
oD33z said:
I tried installing your new negalite the same way as I do the old version and at the end of the install procedure I get an error about set permissions. After that - reboot, wipe dalvik, reboot - it just reboots into recovery. I tried many times with SmartFlash enabled and disabled. I go back and install r121 with no problems.
Click to expand...
Click to collapse
Here. Try this
https://www.androidfilehost.com/?fid=23578570567720169
Sent from my DOWNGRADED EVO 3D, remember all development is done on my phone, not a computer