Related
First of I would like to say thanks to this forum.
I try not to post any problems that have already been answered and this forum was a big help in getting my xda unlocked.
However I had only had my phone in working condition for 2 weeks, enough time to start to like it, when it fell and cracked.
I ordered a new glass screen (no bleeding ink) and had it overnighted. I sucessfully swapped out the broken scree, but in the process I screwed up the phone. So here is whats going on with it, if anyone can help me out it would be awesome.
When taking it apart I accidently broke 2 of the connectors for the ribbon cables on the back of the pcb. Now the phone wont turn on. The screen comes up but its just white and I cant tell if the os is loading.
Sorry for the long winded post
Thanks for the help
Chris
Also if this cant be fixed whats my best option, selling it broken or parting it out? How much could i get?
Re: Some help for a newbie... [borken screen]
beggy said:
When taking it apart I accidently broke 2 of the connectors for the ribbon cables on the back of the pcb. Now the phone wont turn on. The screen comes up but its just white and I cant tell if the os is loading.
Click to expand...
Click to collapse
Well, I guess it depends on how broken the connectors are, but this definitely doesn't sound good...
If you post a few close-up pictures, I'll tell you if there's any hope for fixing it.
Well..
One of those 3 connectors lead to the screen.
My wild guess would be that it's not porperly connected since it's borken.
In that case, I would have done one of two things:
1. Buy a connector through an electronics component vendor, then ,manually replace the broken one or have a electronics lab do it for me.
2. Solder the wires to the connector's base manually (or in a lab) to over-ride it. (I hope you understand what I mean).
At any case, my guess would be a broken connection somewhere in the connectors (one of the 3). This can probably be fixed that way or another.
BTW - I have a lot of dust between the glass and the screen. How do you remove the glass from the screen (it seems to be attached firmly somehow)??
To take the glass apart from the lcd, there are 4 metal tabs (2 at the top and 2 on the bottom) you can pry a thin flat-head screwdriver between the metal tabs (you will see what I am talking about, when you look closer). It will sound bad but its just the glue coming apart.
I tried to get the connectors but had no luck finding a match.
So I am going to part out the phone.
Ill be posting the ebay auctions for the lcd screen, the new glass piece, the motherboard, the battery/case and whatever misc accesories I have lying around.
Before I put all the parts on ebay, I figured I would give the people on here a crack at it. I will entertain all reasonable offers. Send me a PM.
Here is what I have for sale
Case in good condition w/ battery
Motherboard - in good condition just missing the two plastic pieces where the lcd connects.
Brand new glass touchscreen/digitizer
Lcd Screen
Also for sale the in-wall charger, the sync cradle with an extra 3 stylus (styli?).
Hi,
I recently purchased a HD2 on eBay. It was supposed to come immaculate but unfortunately there are dents on almost all corners. Rest if perfect.
I saw on eBay some chinese sellers selling new housing + battery covers for ~25 USD. So why not replacing the housing then? I decided to give it a try.
Well I have to say that it really did not work like in the videos I saw on youtube. I removed the 4 screws under the battery cover, gently pressed the back of the LCM outward but it really refused to pop out (no even half an inch). I discarded the pry tool (a very thine credit card actually) and even tried using a suction cup on the digitizer to pull it backwards but same problem. It's like the LCM/chassis was glued on the bezel. Phone has never been disassembled before (white sticker and void screw were still both there).
This is strange because in all the videos I saw the LCM/middle chassis was clearly not glued on the bezel. It immediately popped out a bit then you could start prying (and praying!). Ok I know that in those videos usually the phone has already been disassembled before so other attempts require less force to do it again for the recording.
My questions now to all the people who managed to do this. Did this require so much force? Is there a change and is HTC now glueing this part the LCM/middle chassis to the bezel? Any suggestion? Where is for you the best place to insert the pry tool when you start?
Thanks and regards,
Try flexing the plastic bezel above the earphone outwards a little while applying slight pressure to the sticker area on the back. There're two notches above which locks the frame to the pcb.
Hi,
Thanks for your help.
I will try that later.
I guess I might need to find a better pry tool.
BR.
Ok I managed to do it.
This required clearly some force on the pry tool (actually I used two plastic cards : a very thin and flexible one than a credit card). I started the operation above the earphone area.
Applying pressure on the sticker area was stresfull because the LCD immediately reacted to the pressure (hence a risk to break it or damage it). Best was to put two fingers on the sticker area to help the LCM module to pop out but with (almost) no pressure.
I had a doubt and now that I managed to remove the housing it's gone. The antennas (those white stuff you see in both top corners and at the bottom) are glued to the housing.
I prefer to spend a few more bucks to take a housing which has those antennas already in.
BR.
i had a similar frustrating experience to yours in trying to snap the back off the chassis on my hd2 which had a fingerprint on the *inside* of the camera cover glass which i needed to open it to get at.
it sure looks easy in that HTC disassembly video on youtube but the tech there is using a sort of plastic hooked tool for the job, which i didn't have, so i used my thumbnail instead in the same place (the upper left corner, looking at the phone from the front) and it took me a good 20 minutes of applying what seemed like unreasonable pressure to my touchscreen and nearly tearing my nail off to get it to pop out.
those snap-tabs the electronics manufacturers use to hold cases together -- even when they also have screws to do the job -- are one of my all-time pet hates. i usually end up breaking them off.
I will be doing the same thing soon. So the housing you removed has antennas glued to it ?. Thanks for that, I will try get new housing with antenna together if possible.
I replaced my screen a while back and can confirm the main body of the hd2 is glued to the sides of the chassis.
It does come out but with a lot of force but pry the glue lose around the whole chassis first by sliding a thin card right ot the bottom of the case and slowlyu move and pry it upwards with 2 cards one on the top and other on the right after you losend the glue. the top has the wifi adapter n that so be careful bottom has usb so mite break.
honestly i would say don't bother replacing it and just get a gel case or something to hide the damage. there's a high chance of messing the digitizer up and would just cause you more trouble of taking the whole phone apart bit by bit and trust me the components are tiny so easily breakable especially the ribbon cables they decided to use. my honest opinion don't
fallenmonk said:
I will be doing the same thing soon. So the housing you removed has antennas glued to it ?. Thanks for that, I will try get new housing with antenna together if possible.
Click to expand...
Click to collapse
yep they are white thin bits glued to the top portion of the case. wifi on left and phone on right if i remember. its been quite a while though since i took my old hd2 apart
Now that I know how to do this I will be easier next time.
Yes antennas are glued in the housing so best is to buy a housing which has antennas already in.
Important note : the antenna which is at the bottom of the housing exists in two different versions : EU or US so check with the seller which one he sells.
BR.
Top left : Amphenol-BT&Wifi-090820
Top right : Amphenol-GPS-090820
Bottom : Amphenol-EU-090828
If T-Mobiles US you need Amphenol-US
sirec said:
I replaced my screen a while back and can confirm the main body of the hd2 is glued to the sides of the chassis.
It does come out but with a lot of force but pry the glue lose around the whole chassis first by sliding a thin card right ot the bottom of the case and slowlyu move and pry it upwards with 2 cards one on the top and other on the right after you losend the glue. the top has the wifi adapter n that so be careful bottom has usb so mite break.
honestly i would say don't bother replacing it and just get a gel case or something to hide the damage. there's a high chance of messing the digitizer up and would just cause you more trouble of taking the whole phone apart bit by bit and trust me the components are tiny so easily breakable especially the ribbon cables they decided to use. my honest opinion don't
Click to expand...
Click to collapse
i don't believe it's glued. as far as i can see the the case is held together with screws and plastic interlocking tabs. the trick is to get the latter to unclip.
No glue indeed just notches locking the LCM module to the bezel
Ok case closed
I got my new housing and the replacement went fine. For those who could be interrested I bought it on ebay from the seller forceviewer_uk in China. Everything went perfect so I can recommend this guy.
Does anyone know how to take a G-Tab apart and repair a broken power connector? My son pulled it off of the table where it was charging and it landed squarely on the adapter where it was plugged into the GTab. Everything else works, but charging, of course, does not.
stalnakerz said:
Does anyone know how to take a G-Tab apart and repair a broken power connector? My son pulled it off of the table where it was charging and it landed squarely on the adapter where it was plugged into the GTab. Everything else works, but charging, of course, does not.
Click to expand...
Click to collapse
Buy a dock, that's what I did
stalnakerz said:
Does anyone know how to take a G-Tab apart and repair a broken power connector? My son pulled it off of the table where it was charging and it landed squarely on the adapter where it was plugged into the GTab. Everything else works, but charging, of course, does not.
Click to expand...
Click to collapse
Choice 1: Buy a dock.
Choice 2: Open it up and solder it back in.
Choice 3: Sell your son to a slave labor camp and use the money to buy a new tablet.
Stolen from another forum about performing a hardware reset:
Disassemble the tablet. Remove the four rubber stoppers on the bottom of the tablet (put them aside). Next, unscrew the screws under them (keep those too). Next we need to get the back half of the tablet off. Put the tablet face down on a piece of paper or another protective material. Gently work one corner of the tablet until the two halves are slightly separated, then use something thin like a business card to keep them slightly parted. You can then use something thin and strong, like a plastic gift card to zip around the edges and break the seal. Prying will only damage your plastics.
snowzach said:
Stolen from another forum about performing a hardware reset:
Disassemble the tablet. Remove the four rubber stoppers on the bottom of the tablet (put them aside). Next, unscrew the screws under them (keep those too). Next we need to get the back half of the tablet off. Put the tablet face down on a piece of paper or another protective material. Gently work one corner of the tablet until the two halves are slightly separated, then use something thin like a business card to keep them slightly parted. You can then use something thin and strong, like a plastic gift card to zip around the edges and break the seal. Prying will only damage your plastics.
Click to expand...
Click to collapse
pulling it apart is one thing, resoldering the connection is another. I've read that it's really tricky (and small) Mine started acting up, had to have the plug on a weird angle for the tablet ot start charging. I thought it was the chord, but it must be the hardware inside the tablet that caused it. I bought a dock, and a second charger...the dock works BEAUTIFULLY for charging, and for watching movies on the big screen via the HDMI port on the dock...
Viewsonic G connector input jack power jack
If you need to replace the jack, you can get it at Ebay.....just type in Viewsonic G jack or power jack and they have them there.
Do anyone has video or pdf or wtever guide to give the instruction how to disassemble the flyer?(i am thinking to repair the flyer myself) Thank you
Here you go:
www.techrepublic.com/photos/crackin...3?seq=2&tag=content;siu-container#photo-frame
thx, but i have 1 more question, do u know how to remove the digitizer? is it the same way as other smartphone?(use hot gun and remove the digitizer?)
athris said:
thx, but i have 1 more question, do u know how to remove the digitizer? is it the same way as other smartphone?(use hot gun and remove the digitizer?)
Click to expand...
Click to collapse
Yes, there is a note in the techrepublic teardown about it being bonded like a smartphone. You should however be vary careful given the size of the screen more heat (not temperature) is required, and the risk of thermally cracking the underlying LCD panel is correspondingly higher.
Beware! Learn from my adventures.
So, I took apart my wife's HTC Flyer this past week to replace the screen. While the Techrepublic teardown shots are helpful, it's missing about ten steps at the end that involve actually removing the screen. I've messed around with tabletpc's and laptops before but not cell phones so wasn't really prepared for the fact that you have to pretty much take the whole Flyer apart in order to be able to get the screen off. As far as I can tell, no one else has documented taking one of these apart to replace the screen. I will write up something more involved when I get a chance but here's a couple things that I found out about the screen.
1. The part of the screen that you touch with your finger and stylus is not glass! It is a heavy plastic layer that is adhered to the glass digitizer. It is clear with the black around the edge and cutout for the HTC logo. This was the part of my screen that had chips in it. I tried to use a screen repair kit to repair the chips (which I did) but it took off the outer, darker finish in the process. So I moved to the next step, replacing the screen. I didn't know about the outer layer, otherwise that would have been much easier to replace. But, I don't think you can get that part unless you have connections with HTC.
2. The outer layer/digitizer glass comes as one part (along with the n-trig connector). I ordered mine for around $50 on ebay.
3. You will need to take the back off and much of the motherboard to be able to disconnect the n-trig connector.
4. Taking the screen off will take heat. I used a hair dryer but more heat could be better although you have to be careful of the lcd underneath. My digitizer broke while removing and ending up putting a small gouge in the lcd. I was able to fix the lcd well enough, just be careful.
5. HTC used a buttload of sticky tape to secure the glass to the lcd and case. My cheap blue pry tool quickly broke so I ended up using a plastic butter knife to separate digitizer from the case. Once off, I used Goo Be Gone to get rid of all the sticky tape from it. I'm ready to put new tape on but I'm not sure exactly what they used. Anyone have any ideas? It's a black, closed cell sticky tape that is really stringy when it comes to taking off. Most of the stuff I see for sale online seems to be really thin stuff. I picked up some Scotch Outdoor Mounting Tape by 3M that looks to be similar that I am going to experiment with. Anyone know for sure what they used?
6. I put the new digitizer on temporarily to check to see if it worked and it did (yay)! But I still need need to cut all of the tape and put it in the right spot. There are also these little plastic tabs that go on the backside of the screen. They are used to refract light from the led's to light up the outside navigation buttons. Be careful not to lose these. I did, and had to make one. We'll see how I did once I get it back together.
7. I found that there's not a lot of parts out there for these things. At least not compared to cell phones. Now that they're being discontinued, I don't know if that is going to help.
Anyway, I took a few pics along the way and will try to write something up when I get more time. I just wanted to give folks a heads-up on the screen and how it's put together. I can't imagine the View's screen is any different. So whatever they're using for the outer layer isn't Gorilla Glass. Or is it?
UPDATE:
Here are the promised photos of this disaster. I'll add the commentary tomorrow (I'm tired).
Two more comments and I can finally upload my photos.
I need to replace my LCD and Glass...anyone know where I can order these parts...I cant find them anywhere.
Hard to find parts for the Flyer/View which could be a problem. Looks like some is selling an LCD, though on eBay.
http://www.ebay.com/itm/PH-LCD-HT-2...360?pt=LH_DefaultDomain_0&hash=item27bf8f0390 from my PG41200 using Tapatalk
I purchased mine here and it works great.
http://www.ebay.com/itm/260906551668?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Much better price. What kind of tape did you use? Also did you have to replace any of the light reflacting plastic tabs that are used to light the buttons around the outside of the digitizer?
Sent from my PG41200 using Tapatalk
Will a replacement screen for the Flyer work well on a View?
I don't see why not. Except for some of the internals, they are pretty much identical hardware wise.
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
The best reason for replacing both is that you won't have to worry about binding them or getting dust between them if you get them together preassembled. As to the rest, I can't say. I know we have a few people here who have done it.
So I found the adhesive strips that I need. It comes as a bulk sheet where you cut them to fit. I am going with replacing only the digitizer. Replacing the LCD screen also would male the process easier however I fear getting a replacement screen that is in worse shape or more poorly made than the original one my phone came with. I know this one has no flaws.
So I have answered my questions already. I'll post here when I done replacing the digitizer with anything that is of interest in case someone else has questions about this procedure.
Thank you for your input shrike1978. Much appreciated.
Regards,
Eduard Tieseler
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
Click to expand...
Click to collapse
Check out my thread: http://forum.xda-developers.com/showthread.php?t=2189789
I did it not long ago, and was fine. However, I opted to go for the digitizer + LCD assembly, as I didn't want to have to worry about separating the digitizer from the LCD and worrying about dust.
To answer your questions:
1) It's eaiser, takes less time, and you don't have to worry about dust with replacing the digitizer + LCD assembly.
2) Replace the adhesive. I tried reusing it... and it has some flex on it. So I got some new adhesive, scraped the old stuff off, put the new one, and used a heatgun to move the screen assembly around to get it to fit right, and then pressed it down as it cooled to secure it better.
3) Ebay
4) Not sure on this one... not that I know of anyway.
5) If you get the parts from eBay, then they sometimes come with tools (Torx, philips, and a plastic separator tool).
I also linked the video that I used in my thread, so you can look at that. It's pretty straightforward and easy to do. Took me about 45 minutes to just over an hour to do everything, as I was taking my time.
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
etieseler said:
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
Click to expand...
Click to collapse
I also purchased the full assembly and was able to switch the new parts onto my Rezound. Unfortunately, the earpiece (the part you listen to when NOT on speakerphone) and the proximity sensor did not work with the new set, and I am swapping it for a replacement. However, I've been inside the unit now 5 times, and I suggest in addition to the tools supplied with the sets (t5, small phillips and separator) you also have a small flathead (helps with starting the split the unit apart and also with pulling and reattaching the vibrator motor) and a long tweezers (invaluable when trying to reconnect the ribbon cables.)
Also, reconnect the MIDDLE ribbon cable (which is slightly twisted and longer) first, then reconnect the top, and don't forget to reapply the insulating tape (been there, done that).
Watch the take apart video on Youtube repeatedly until you can do it with your eyes closed, and be careful, the red plastic does break easily, especially on the corners.
Replaced my digitizer with good success, using new adhesive. Upon first re-assembly the digitizer was popping out of the plastic bezel a bit, but everything worked great, touch, display, everything. So I decided to take apart, add some more adhesive strips. Now the digitizer stays flush.
First boot after 2nd re-assembly, got boot with first vibrate, but no screen on. So I pull the battery to attempt again. Now I receive no vibrate response from power button. When plug into charger, orange light comes on for 5 seconds and then off indefinitely. This happens each time after battery pull+wall charger plugin.
I have tried multiple times disassembling, checking both ribbon cables that plugin to motherboard, appear to connect fine. Visually all other aspects of MB appear fine.
Any ideas anyone? Not sure what may have broke. I should have left well-enough alone, but the digitizer was somewhat spongey to touch on right side of screen and I could see white light shine up... TIA
Each time I pull the batt the orange light will come on solid for 5 or so sec, then off for good. One time even started flashing for a bit like it was charging from full depletion (like it does before it lets you power on). Not sure how to diagnose.
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
Click to expand...
Click to collapse
I did not put those pieces of tape back on. In the YouTube video by "injured gadgets," I don't believe they re-covered up those ribbon cable plugins, so I also did not during re-assembly. Should I try that? Or, I assume, my board somewhere has gone bad? (Phone did work just fine after re-assemble, until I decided to take apart again)
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
hgoldner said:
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
Click to expand...
Click to collapse
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
I would go ahead and try putting it back on. There was an earlier post where someone mentioned it was important to put it back on, perhaps he can comment on what can happen if its not on (He said he learned from experience). Perhaps you can PM him.
To be honest, I originally only put the tape back on one connection, but after the second time replacing both the LCD screen and the digitizer, I found the second piece of tape and now both are back on.
What can it hurt to see if that will fix it? Its fairly easy to get to on these phones.
Ed
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
red3razor said:
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
Click to expand...
Click to collapse
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
carngeX said:
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
Click to expand...
Click to collapse
I left it off on one connection for about a week also with no issues. However I did notice roughly a 16th of an inch of copper exposed on the ribbon. I can envision potential issues from that. I'm not sure about your phone, but the jaw connectors on mine would never open on their own. Far too much resistance to open from any vibration or movement. The vibrator motor connection had a better chance of disconnecting on its own than the ribbon cables. I'm sure that tape provides more than just locking the jaw connectors closed. I could be wrong though.
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
No, I remembered and put it on before I powered up.
Dumped down the innertubes from my Asus Transformer TF300T
Just replaced my digitizer two days ago and I must add the difference is like night and day. I noted in a post that I had tripped and fell on it with my knee...lol ..nope.. I threw the damn thing and it hit the wall. Yahhh.. I know stupid lol... Something really pi$$ed me off tho and I kinda lost it.. .poooof....... Anyway, I had about 30 cracks in my digitizer and amazingly it still worked. Replaced it two days ago and it works great.
That factory adhesive is some SERIOUS stuff. I have performed many electronics repairs over the years and this...well...removing the digitizer and applying the new strips in exactly the right size was a royal pain in the a**! You REALLY gotta get that digitizer glass HOT if you want to be able to loosen it. Light heating WONT do squat to it. And the new strips arent even half as strong as the factory stuff. You really need patience and precision here.
Yes, dust ISVan issue where I live. Canned air came VERY useful. Also its good to have isopropyl alcohol and soft paper towels so you can clean any smudges you make on the LCD before reapplying the digitizer glass. Basically it's best to blow air over it quickly as you press the digi down to the adhesive. That makes sure every bit of contaminant is out.
About the ribbon cables, no I didn't reapply the amber tape to the jawbone connectors. Much of their adhesiveness was lost when I pulled them off. And as long as the ribbon cables are seated in properly and the jawbone connectors are securely locked down, they wont come disconnected. The tape is only there as an additional measure to secure the jawbone connectors from unlocking. Unless you drop your phone on concrete a lot, those cables arent coming loose....even then, dropping it wouldnt knock those loose.. Its more secure than you think. As far as the phone NOT working, the orange tape would have NO effect on that. Maybe one of your cables were partially disconnected and shorted out something on the mainboard. Either that, or it is static sensitive. Its possible if anything is CMOS.
ONLY issue I have since the repair is the top of the digitizer keeps pushing up because of the digitizer ribbon cable and where you have to bend and fold it in that groove to guide it behind the LCD . The ribbon isnt pinching down well and acts as a spring on the digitizer glass....adhesive not doing anything for that.
oh, did you all remove and reapply the clear (4 button tabs) at the bottom to the new glass? got mine in (the lights are pink now ...weeee ) Had to use some Gorilla super glue to restick them. That adhesive at the bottom was super strong and somehow they lost their stickiness when I pulled them off.
Digitizer after I finally got it unstuck from the LCD... wheewww damn. Lots of cracks. Thats what happens when the phone face eats the wall.....
So, my 4 soft keys on the bottom have yet out. Would fixing the digitzer get them back to working? My screens just got cracked like 2 days ago too, and I just want to make sure before i do all this and then find out i gotta take it all apart again. Thanks in Advance!