Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
The best reason for replacing both is that you won't have to worry about binding them or getting dust between them if you get them together preassembled. As to the rest, I can't say. I know we have a few people here who have done it.
So I found the adhesive strips that I need. It comes as a bulk sheet where you cut them to fit. I am going with replacing only the digitizer. Replacing the LCD screen also would male the process easier however I fear getting a replacement screen that is in worse shape or more poorly made than the original one my phone came with. I know this one has no flaws.
So I have answered my questions already. I'll post here when I done replacing the digitizer with anything that is of interest in case someone else has questions about this procedure.
Thank you for your input shrike1978. Much appreciated.
Regards,
Eduard Tieseler
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
Click to expand...
Click to collapse
Check out my thread: http://forum.xda-developers.com/showthread.php?t=2189789
I did it not long ago, and was fine. However, I opted to go for the digitizer + LCD assembly, as I didn't want to have to worry about separating the digitizer from the LCD and worrying about dust.
To answer your questions:
1) It's eaiser, takes less time, and you don't have to worry about dust with replacing the digitizer + LCD assembly.
2) Replace the adhesive. I tried reusing it... and it has some flex on it. So I got some new adhesive, scraped the old stuff off, put the new one, and used a heatgun to move the screen assembly around to get it to fit right, and then pressed it down as it cooled to secure it better.
3) Ebay
4) Not sure on this one... not that I know of anyway.
5) If you get the parts from eBay, then they sometimes come with tools (Torx, philips, and a plastic separator tool).
I also linked the video that I used in my thread, so you can look at that. It's pretty straightforward and easy to do. Took me about 45 minutes to just over an hour to do everything, as I was taking my time.
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
etieseler said:
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
Click to expand...
Click to collapse
I also purchased the full assembly and was able to switch the new parts onto my Rezound. Unfortunately, the earpiece (the part you listen to when NOT on speakerphone) and the proximity sensor did not work with the new set, and I am swapping it for a replacement. However, I've been inside the unit now 5 times, and I suggest in addition to the tools supplied with the sets (t5, small phillips and separator) you also have a small flathead (helps with starting the split the unit apart and also with pulling and reattaching the vibrator motor) and a long tweezers (invaluable when trying to reconnect the ribbon cables.)
Also, reconnect the MIDDLE ribbon cable (which is slightly twisted and longer) first, then reconnect the top, and don't forget to reapply the insulating tape (been there, done that).
Watch the take apart video on Youtube repeatedly until you can do it with your eyes closed, and be careful, the red plastic does break easily, especially on the corners.
Replaced my digitizer with good success, using new adhesive. Upon first re-assembly the digitizer was popping out of the plastic bezel a bit, but everything worked great, touch, display, everything. So I decided to take apart, add some more adhesive strips. Now the digitizer stays flush.
First boot after 2nd re-assembly, got boot with first vibrate, but no screen on. So I pull the battery to attempt again. Now I receive no vibrate response from power button. When plug into charger, orange light comes on for 5 seconds and then off indefinitely. This happens each time after battery pull+wall charger plugin.
I have tried multiple times disassembling, checking both ribbon cables that plugin to motherboard, appear to connect fine. Visually all other aspects of MB appear fine.
Any ideas anyone? Not sure what may have broke. I should have left well-enough alone, but the digitizer was somewhat spongey to touch on right side of screen and I could see white light shine up... TIA
Each time I pull the batt the orange light will come on solid for 5 or so sec, then off for good. One time even started flashing for a bit like it was charging from full depletion (like it does before it lets you power on). Not sure how to diagnose.
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
Click to expand...
Click to collapse
I did not put those pieces of tape back on. In the YouTube video by "injured gadgets," I don't believe they re-covered up those ribbon cable plugins, so I also did not during re-assembly. Should I try that? Or, I assume, my board somewhere has gone bad? (Phone did work just fine after re-assemble, until I decided to take apart again)
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
hgoldner said:
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
Click to expand...
Click to collapse
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
I would go ahead and try putting it back on. There was an earlier post where someone mentioned it was important to put it back on, perhaps he can comment on what can happen if its not on (He said he learned from experience). Perhaps you can PM him.
To be honest, I originally only put the tape back on one connection, but after the second time replacing both the LCD screen and the digitizer, I found the second piece of tape and now both are back on.
What can it hurt to see if that will fix it? Its fairly easy to get to on these phones.
Ed
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
red3razor said:
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
Click to expand...
Click to collapse
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
carngeX said:
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
Click to expand...
Click to collapse
I left it off on one connection for about a week also with no issues. However I did notice roughly a 16th of an inch of copper exposed on the ribbon. I can envision potential issues from that. I'm not sure about your phone, but the jaw connectors on mine would never open on their own. Far too much resistance to open from any vibration or movement. The vibrator motor connection had a better chance of disconnecting on its own than the ribbon cables. I'm sure that tape provides more than just locking the jaw connectors closed. I could be wrong though.
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
No, I remembered and put it on before I powered up.
Dumped down the innertubes from my Asus Transformer TF300T
Just replaced my digitizer two days ago and I must add the difference is like night and day. I noted in a post that I had tripped and fell on it with my knee...lol ..nope.. I threw the damn thing and it hit the wall. Yahhh.. I know stupid lol... Something really pi$$ed me off tho and I kinda lost it.. .poooof....... Anyway, I had about 30 cracks in my digitizer and amazingly it still worked. Replaced it two days ago and it works great.
That factory adhesive is some SERIOUS stuff. I have performed many electronics repairs over the years and this...well...removing the digitizer and applying the new strips in exactly the right size was a royal pain in the a**! You REALLY gotta get that digitizer glass HOT if you want to be able to loosen it. Light heating WONT do squat to it. And the new strips arent even half as strong as the factory stuff. You really need patience and precision here.
Yes, dust ISVan issue where I live. Canned air came VERY useful. Also its good to have isopropyl alcohol and soft paper towels so you can clean any smudges you make on the LCD before reapplying the digitizer glass. Basically it's best to blow air over it quickly as you press the digi down to the adhesive. That makes sure every bit of contaminant is out.
About the ribbon cables, no I didn't reapply the amber tape to the jawbone connectors. Much of their adhesiveness was lost when I pulled them off. And as long as the ribbon cables are seated in properly and the jawbone connectors are securely locked down, they wont come disconnected. The tape is only there as an additional measure to secure the jawbone connectors from unlocking. Unless you drop your phone on concrete a lot, those cables arent coming loose....even then, dropping it wouldnt knock those loose.. Its more secure than you think. As far as the phone NOT working, the orange tape would have NO effect on that. Maybe one of your cables were partially disconnected and shorted out something on the mainboard. Either that, or it is static sensitive. Its possible if anything is CMOS.
ONLY issue I have since the repair is the top of the digitizer keeps pushing up because of the digitizer ribbon cable and where you have to bend and fold it in that groove to guide it behind the LCD . The ribbon isnt pinching down well and acts as a spring on the digitizer glass....adhesive not doing anything for that.
oh, did you all remove and reapply the clear (4 button tabs) at the bottom to the new glass? got mine in (the lights are pink now ...weeee ) Had to use some Gorilla super glue to restick them. That adhesive at the bottom was super strong and somehow they lost their stickiness when I pulled them off.
Digitizer after I finally got it unstuck from the LCD... wheewww damn. Lots of cracks. Thats what happens when the phone face eats the wall.....
So, my 4 soft keys on the bottom have yet out. Would fixing the digitzer get them back to working? My screens just got cracked like 2 days ago too, and I just want to make sure before i do all this and then find out i gotta take it all apart again. Thanks in Advance!
Related
First of I would like to say thanks to this forum.
I try not to post any problems that have already been answered and this forum was a big help in getting my xda unlocked.
However I had only had my phone in working condition for 2 weeks, enough time to start to like it, when it fell and cracked.
I ordered a new glass screen (no bleeding ink) and had it overnighted. I sucessfully swapped out the broken scree, but in the process I screwed up the phone. So here is whats going on with it, if anyone can help me out it would be awesome.
When taking it apart I accidently broke 2 of the connectors for the ribbon cables on the back of the pcb. Now the phone wont turn on. The screen comes up but its just white and I cant tell if the os is loading.
Sorry for the long winded post
Thanks for the help
Chris
Also if this cant be fixed whats my best option, selling it broken or parting it out? How much could i get?
Re: Some help for a newbie... [borken screen]
beggy said:
When taking it apart I accidently broke 2 of the connectors for the ribbon cables on the back of the pcb. Now the phone wont turn on. The screen comes up but its just white and I cant tell if the os is loading.
Click to expand...
Click to collapse
Well, I guess it depends on how broken the connectors are, but this definitely doesn't sound good...
If you post a few close-up pictures, I'll tell you if there's any hope for fixing it.
Well..
One of those 3 connectors lead to the screen.
My wild guess would be that it's not porperly connected since it's borken.
In that case, I would have done one of two things:
1. Buy a connector through an electronics component vendor, then ,manually replace the broken one or have a electronics lab do it for me.
2. Solder the wires to the connector's base manually (or in a lab) to over-ride it. (I hope you understand what I mean).
At any case, my guess would be a broken connection somewhere in the connectors (one of the 3). This can probably be fixed that way or another.
BTW - I have a lot of dust between the glass and the screen. How do you remove the glass from the screen (it seems to be attached firmly somehow)??
To take the glass apart from the lcd, there are 4 metal tabs (2 at the top and 2 on the bottom) you can pry a thin flat-head screwdriver between the metal tabs (you will see what I am talking about, when you look closer). It will sound bad but its just the glue coming apart.
I tried to get the connectors but had no luck finding a match.
So I am going to part out the phone.
Ill be posting the ebay auctions for the lcd screen, the new glass piece, the motherboard, the battery/case and whatever misc accesories I have lying around.
Before I put all the parts on ebay, I figured I would give the people on here a crack at it. I will entertain all reasonable offers. Send me a PM.
Here is what I have for sale
Case in good condition w/ battery
Motherboard - in good condition just missing the two plastic pieces where the lcd connects.
Brand new glass touchscreen/digitizer
Lcd Screen
Also for sale the in-wall charger, the sync cradle with an extra 3 stylus (styli?).
Hi,
I recently purchased a HD2 on eBay. It was supposed to come immaculate but unfortunately there are dents on almost all corners. Rest if perfect.
I saw on eBay some chinese sellers selling new housing + battery covers for ~25 USD. So why not replacing the housing then? I decided to give it a try.
Well I have to say that it really did not work like in the videos I saw on youtube. I removed the 4 screws under the battery cover, gently pressed the back of the LCM outward but it really refused to pop out (no even half an inch). I discarded the pry tool (a very thine credit card actually) and even tried using a suction cup on the digitizer to pull it backwards but same problem. It's like the LCM/chassis was glued on the bezel. Phone has never been disassembled before (white sticker and void screw were still both there).
This is strange because in all the videos I saw the LCM/middle chassis was clearly not glued on the bezel. It immediately popped out a bit then you could start prying (and praying!). Ok I know that in those videos usually the phone has already been disassembled before so other attempts require less force to do it again for the recording.
My questions now to all the people who managed to do this. Did this require so much force? Is there a change and is HTC now glueing this part the LCM/middle chassis to the bezel? Any suggestion? Where is for you the best place to insert the pry tool when you start?
Thanks and regards,
Try flexing the plastic bezel above the earphone outwards a little while applying slight pressure to the sticker area on the back. There're two notches above which locks the frame to the pcb.
Hi,
Thanks for your help.
I will try that later.
I guess I might need to find a better pry tool.
BR.
Ok I managed to do it.
This required clearly some force on the pry tool (actually I used two plastic cards : a very thin and flexible one than a credit card). I started the operation above the earphone area.
Applying pressure on the sticker area was stresfull because the LCD immediately reacted to the pressure (hence a risk to break it or damage it). Best was to put two fingers on the sticker area to help the LCM module to pop out but with (almost) no pressure.
I had a doubt and now that I managed to remove the housing it's gone. The antennas (those white stuff you see in both top corners and at the bottom) are glued to the housing.
I prefer to spend a few more bucks to take a housing which has those antennas already in.
BR.
i had a similar frustrating experience to yours in trying to snap the back off the chassis on my hd2 which had a fingerprint on the *inside* of the camera cover glass which i needed to open it to get at.
it sure looks easy in that HTC disassembly video on youtube but the tech there is using a sort of plastic hooked tool for the job, which i didn't have, so i used my thumbnail instead in the same place (the upper left corner, looking at the phone from the front) and it took me a good 20 minutes of applying what seemed like unreasonable pressure to my touchscreen and nearly tearing my nail off to get it to pop out.
those snap-tabs the electronics manufacturers use to hold cases together -- even when they also have screws to do the job -- are one of my all-time pet hates. i usually end up breaking them off.
I will be doing the same thing soon. So the housing you removed has antennas glued to it ?. Thanks for that, I will try get new housing with antenna together if possible.
I replaced my screen a while back and can confirm the main body of the hd2 is glued to the sides of the chassis.
It does come out but with a lot of force but pry the glue lose around the whole chassis first by sliding a thin card right ot the bottom of the case and slowlyu move and pry it upwards with 2 cards one on the top and other on the right after you losend the glue. the top has the wifi adapter n that so be careful bottom has usb so mite break.
honestly i would say don't bother replacing it and just get a gel case or something to hide the damage. there's a high chance of messing the digitizer up and would just cause you more trouble of taking the whole phone apart bit by bit and trust me the components are tiny so easily breakable especially the ribbon cables they decided to use. my honest opinion don't
fallenmonk said:
I will be doing the same thing soon. So the housing you removed has antennas glued to it ?. Thanks for that, I will try get new housing with antenna together if possible.
Click to expand...
Click to collapse
yep they are white thin bits glued to the top portion of the case. wifi on left and phone on right if i remember. its been quite a while though since i took my old hd2 apart
Now that I know how to do this I will be easier next time.
Yes antennas are glued in the housing so best is to buy a housing which has antennas already in.
Important note : the antenna which is at the bottom of the housing exists in two different versions : EU or US so check with the seller which one he sells.
BR.
Top left : Amphenol-BT&Wifi-090820
Top right : Amphenol-GPS-090820
Bottom : Amphenol-EU-090828
If T-Mobiles US you need Amphenol-US
sirec said:
I replaced my screen a while back and can confirm the main body of the hd2 is glued to the sides of the chassis.
It does come out but with a lot of force but pry the glue lose around the whole chassis first by sliding a thin card right ot the bottom of the case and slowlyu move and pry it upwards with 2 cards one on the top and other on the right after you losend the glue. the top has the wifi adapter n that so be careful bottom has usb so mite break.
honestly i would say don't bother replacing it and just get a gel case or something to hide the damage. there's a high chance of messing the digitizer up and would just cause you more trouble of taking the whole phone apart bit by bit and trust me the components are tiny so easily breakable especially the ribbon cables they decided to use. my honest opinion don't
Click to expand...
Click to collapse
i don't believe it's glued. as far as i can see the the case is held together with screws and plastic interlocking tabs. the trick is to get the latter to unclip.
No glue indeed just notches locking the LCM module to the bezel
Ok case closed
I got my new housing and the replacement went fine. For those who could be interrested I bought it on ebay from the seller forceviewer_uk in China. Everything went perfect so I can recommend this guy.
So I dropped my phone today, and it must have fell on the corner good enough that it cracked the screen from the top-left to the middle-right.
Going to replace the digitizer/LCD as a combo since it's a bit easier than replacing just the digitizer.
Ordered this today:
http://www.ebay.com/itm/350582267363?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649
Watched a couple of the repair videos (specifically this one: http://blog.repairsuniverse.net/how-to-fix-htc-rezound-screen/), and they say that there's adhesive on the back of this assembly as well that you need to pry away from (in the previously linked video, they push the assembly away from the housing from the backside and pry away from the housing/adhesive). My question is... am I going to have to replace this adhesive once I pry the assembly away from the housing? Or should the adhesive that's there be good enough to secure it as long as I don't rip it away very badly?
If I do need to get new adhesive, anybody have any links as to what to get?
Thanks in advance, I appreciate it!
I never replace a screen before. good luck
Bump.
Still haven't done this, as I haven't had time on the weekends yet. Got a GNexus to get me by, but I'm missing my Rezound.
http://www.amazon.com/gp/product/B0069YNZV2/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
doing all this is very tedious work... make sure you get the soft button hinges in correctly or the screen wont sit flat..
agentofchaos said:
http://www.amazon.com/gp/product/B0069YNZV2/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
doing all this is very tedious work... make sure you get the soft button hinges in correctly or the screen wont sit flat..
Click to expand...
Click to collapse
Should be less tedious since I got the LCD/Digitizer assembly together, so I don't have to replace just the digitizer.
I replaced the digitizer on mine last year. The process was just a disaster for me (ended up cracking my LCD)...but since yours is coming with the LCD and digitizer already glued together...perhaps you should have some better luck. It won't be necessarily difficult to do...it could just become a pain.
For one...there are clear tabs attached to the digitizer that essentially "draw" the red LED lights from the board down to the buttons on the bottom. These tabs are literally sandwiched between the digitizer and LCD...you'll see what I mean when you separate the broken digitizer/LCD from the housing...there will be 4 clear tabs sticking out from the bottom of the LCD. I did not find any seller that was selling those tabs, and it's quite possible the one you bought won't have them. What this means is...the 4 capacitive buttons along the bottom will still work, they just won't light up anymore. Not a big deal to some. I tried peeling them off my old digitizer and gluing them to the new one...but that didn't come out right at all. And your new LCD/digitizer will already be glued together and you're probably not going to want to separate them just to try and save the buttons.
Secondly, I've used the 3m double-sided roll of tape (like the one linked to above). It'll probably be your best bet...but know that, you could possibly need to redo it after a while of use. I could push on the top of my screen with my thumb, and I would see it kinda "flex" a bit, so the tape wasn't holding all too well. I'd also get fuzz and dirt on the screen of the front camera over time. So do a good, thorough job taping the digitizer/LCD down to the housing.
I lucked out (sort of) because my wife decided to give her Rez a bath and killed it. So I essentially took her digitizer, LCD and housing and use it on my phone.
OH, and don't overtighten the 6 screws for the red back housing! The bottom two screws especially. I did that and it cracked. And be gentle removing the red housing from the camera..sometimes the camera likes to get stuck inside of the camera housing and prying it apart will destroy it.
OpAckTool said:
I replaced the digitizer on mine last year. The process was just a disaster for me (ended up cracking my LCD)...but since yours is coming with the LCD and digitizer already glued together...perhaps you should have some better luck. It won't be necessarily difficult to do...it could just become a pain.
For one...there are clear tabs attached to the digitizer that essentially "draw" the red LED lights from the board down to the buttons on the bottom. These tabs are literally sandwiched between the digitizer and LCD...you'll see what I mean when you separate the broken digitizer/LCD from the housing...there will be 4 clear tabs sticking out from the bottom of the LCD. I did not find any seller that was selling those tabs, and it's quite possible the one you bought won't have them. What this means is...the 4 capacitive buttons along the bottom will still work, they just won't light up anymore. Not a big deal to some. I tried peeling them off my old digitizer and gluing them to the new one...but that didn't come out right at all. And your new LCD/digitizer will already be glued together and you're probably not going to want to separate them just to try and save the buttons.
Secondly, I've used the 3m double-sided roll of tape (like the one linked to above). It'll probably be your best bet...but know that, you could possibly need to redo it after a while of use. I could push on the top of my screen with my thumb, and I would see it kinda "flex" a bit, so the tape wasn't holding all too well. I'd also get fuzz and dirt on the screen of the front camera over time. So do a good, thorough job taping the digitizer/LCD down to the housing.
I lucked out (sort of) because my wife decided to give her Rez a bath and killed it. So I essentially took her digitizer, LCD and housing and use it on my phone.
OH, and don't overtighten the 6 screws for the red back housing! The bottom two screws especially. I did that and it cracked. And be gentle removing the red housing from the camera..sometimes the camera likes to get stuck inside of the camera housing and prying it apart will destroy it.
Click to expand...
Click to collapse
Thanks for the heads up.
Swapped out the screen (didn't get any 3M tape yet, but I wanted to make sure the screen worked properly / multi-touch was recognized everywhere).
Swapped the screens, re-assembled (managed to leave some adhesive where the lcd/digitizer assembly pulls out of on there, so it sticks, but like what happens with you it flexes just a bit. Will probably order some 3M tape one of these days and take off all of the old adhesive and replace it. Glad you mentioned the issue with the camera getting stuck in the housing; that did happen to me, and I had to work it out of there. The tiny LED board did pop out of it's connector, but I popped it back in easily and it still works fine.
I also didn't put the soft-key light tabs in the new LCD/digitizer (like you said, didn't want to pry the new one apart). Doesn't bother me much anyway, as I had them turned off in my ROM anyway lol.
So far it works well. Won't be my daily again yet until I have some 3M tape to put on there so the assembly is secured in the housing.
Just an update. Got some double-sided tape, and scraped off the old, remnants of the previous tape that was there. Cut new strips to fit where the old ones were, and it fits much more securely now. No screen flex or wiggle anymore. Charging it back up, and thinking about flashing a different ROM now that I have it fixed.
All-in-all, it was a pretty easy fix.
UPDATE: So, the digitizer I bought developed a massive dead zone. I already contacted the amazon store I bought it from, they're replacing it for me. Why does this matter? Because now I get to update this post with pictures/video! So, yeah, I guess this guide should get a lot more helpful soon.
Update 2: Ok, so, I don't even know how to express my anger and frustration. This girl at work shoved my phone out of my hands and into the leg of a table, completely destroying my phone. So, yeah, sorry, I guess I won't be updating with pictures/video, because the amazon store isn't going to take the screen back now.
Yo, guys. If anyone noticed that I was gone, I'm flattered, since I don't post a lot. But yeah, I havent had my Optimus G in about a month, so I havent been on this forum. In that time, I went through my Second Motorola Atrix HD, a broken Galaxy S3, and even lived through Google Voice on my computer. It's an extremely long story, and kind of ridiculous, so I'll spare the details.
HOWEVER, I did finally just buy a replacement Digitizer and LCD screen, and successfully installed it, and I want to share tips for anyone doing it themselves.
When removing the back, after you've removed torx screws, start prying the back off from in between where the Sim card and MicroSD go. Where the back of the phone and the chassis of the phone are separate is much more obvious in that cavity, PLUS dents/dings from jamming a screwdriver in there wont be noticeable when you put the bay cover back on.
Don't force anything off. Make sure you've removed every screw, unclipped every clip, and removed ribbons from everything you're trying to take off.
Removing the battery is tricky. Be careful not to deform it too much, cause that's dangerous. But there are 2 strips of double sided tape running horizontally beneath the battery. Try to get something between the top one and the battery, then carefully pull the battery off the second strip with your hands. sticking too much stuff beneath it to pry it up is going to cause some trouble, so lifting it with your fingers might be better.
Remove the motherboard. detatch all the ribbons, antennae, everything, then pull up from the left, then slide left and out. This is how I got it out with the least resistance, but there is no science to it. If you've gotten this far, you can figure out how to pull it out without breaking it in half.
Components that need to be removed before LCD+Digitizer removal:
Motherboard
Battery
Camera
Just put them off to the side, you don't want them damaged during the next part.
WARNING! If you plan on saving your LCD screen, DO NOT DO THIS. The high heat will cook your screen and make it unusable. Only do this to remove a broken or unsavable Digitizer+LCD.
Alright, now pull out the heat gun. Alternatively, you can do what I did, and use a hair dryer. Not even kidding, this will work fine, and will be hilarious when you tell your friends about it.
On a high heat, start heating the screen. If you're using a heat gun, just do your thing, you know how it works. Hair dryer folks, keep the dryer very low to the phone, low enough to feel the dryer being pushed up by the air, holding it just high enough so it sort of hovers. (You'll know what I mean when you try it. If you don't, just keep it about half an inch off the phone.) Move the dryer along the edges of the screen, all the way around, thats where the glue is. It should heat up pretty fast.
Using your pry tool, start at the speaker grill and pry all the way around the phone. lifting just slightly upwards. If it's not extremely easy, apply more heat. Work all the way around, then pull the screen off. Be careful, it's likely you'll shatter the screen even more at this part if you're not careful. User Bozwell had an excellent suggestion (post 4), cover your screen in tape, then begin separating the screen to keep from getting glass everywhere. Great idea, Boz!
Alright, so from here on out, it's just reassembling your phone correctly. Piece o cake.
Firstly, put your new screen in. If it came with adhesive, it's up to you if you want to apply it now. I'd think you probably have to, but up to you.
If you're like me, and no adhesive was provided, hold off on doing anything for now. Just put the screen in the hole, and thread the ribbons through.
The motherboard lines up with some contacts on the chassis in a few places, but most importantly, there is a connection on the top left corner of the body, and the UNDERSIDE of the motherboard that needs to be made. I believe it's proximity sensor, but not sure. It's very difficult to tell if its attached, but look at what I'm describing, and try your best to mate them.
Don't forget ANY cables. Like, that's pretty obvious, but even when you're sure you didnt forget any, check again. The camera's ribbon is underneath the screen's, don't forget that one. I reassebled the whole thing, everything was working perfectly, except I no longer had any mobile connection. I couldn't imagine what I'd broken, since that's a whole different area, but going to phone status and checking my signal strength revealed I forgot to reconnect the white antennae (status showed my signal at -200,000 dbm). So, double check, because the more often you have to reopen your phone, the more flimsy it's going to get.
Alright, screw the plastic shielding back on, reconnect your battery, then flip the phone to be face up. Power it on, test the screen to make sure it's functional. If all is well, power off and glue the screen in. What I did, and I welcome anyone to tell me a better glue type or method, is plain ol Super glue along all the edges where the old glue was. Press it in, flip it over, and while it's drying, finish reassembling the phone (should just be make sure everything is screwed in inside, then put back glass back on.
If your screen wasn't functional, I guess try to get it replaced by whoever you bought it from, and leave your phone disassembled for when it gets to your house.
Alright, that's pretty much the thick and thin of it, it genuinely isn't that hard of a replacement. I've done a number of digitizer/lcd replacements, not bad at all. I hope this helped anyone stuck or wondering about anything. This video can be used as a rough example, but it goes really fast.
Good Luck!
replacement of lcd/digitzer
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
gruiz3 said:
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
Click to expand...
Click to collapse
Haha that's crazy, it bothers me how fragile this phone seems to be.
To keep the glass shards from going everywhere try covering the screen in tape before you start.
bozwell said:
To keep the glass shards from going everywhere try covering the screen in tape before you start.
Click to expand...
Click to collapse
Great idea, OP updated!
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
MoFoQ said:
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
Click to expand...
Click to collapse
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
ripin150 said:
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
Click to expand...
Click to collapse
I figured...though I've been eye-ing using the screen+digitizer+front housing if and when they get back into stock.
(digitizer only is also out-of-stock)
MY XZU Cable fault ;-c
I try to fix
But, the cable is attached to the motherboard
I do not know what I soldered or heat ;-c
Help the person to fix cables
Attachments Photo!!!
HEXAHN said:
MY XZU Cable fault ;-c
I try to fix
But, the cable is attached to the motherboard
I do not know what I soldered or heat ;-c
Help the person to fix cables
Attachments Photo!!!
Click to expand...
Click to collapse
You can't fix this by yourself, unfortunately. It's glued on with some special adhesive, the contacts are to tiny to solder. The glue you buy on ebay (i assume), next problem is getting the flex cable on the right place and keep it their while glueing.....
You can look for a motherboard replacement, only last time i checked it's almost as expensive as a new phone.
Some manufacturers use small clamps for the flex cable, i assume glue is the trade off for this tiny device...
I've been to this hassle myself, i ended up on buying a new ultra
Has someone have any other suggestions? Have detached the main flex from the board. Had the main flex broken, wanted to fix, but know it's just disassembled. Had display problems before.
Can someone have some ideas? like those clamps you mentioned.
Bro your beating a dead horse, just buy a used one online
hot bar soldering attachment, anisotropic adhesive film/tape( apparently you can buy this for whole sale only. lucky for me the company I work with has spare trimmings of this), microscope or powerful magnifying glass and a lot of patience.
bump, i am in this boat, there must be a dozen lines on the cable, i cant imagine soldering it without shorting it out....
Why do they sell those toys that cannot be repaired by the way?
I'm in the same boat an all y'all being no help are no help so bump outta here already cuz everyone else in this boat looking for the answer doesn't wanna WASTE THEIR TIME on your helpless posts.
To recap we have the solder method which sounds like rubbish as flex cables melt.
Then there's that kind of adhesive glue and/or tape. Clamping is the reason phone companies profits dwindled until they switched to this new clampless method. I'm not gonna buy in bulk cuz I'm not about to start up a cell phone chop shop so maybe get a magnifying headset, some Walmart super glue that says mess free, and use a needle to dab the glue on in the right points but don't cover any contacts!
Did anyone ever managed to get this done?
I also recently experienced, looking at google solution does not get the information.
Try YouTube? I'm sure it applies to other z models
jigzerx said:
Did anyone ever managed to get this done?
Click to expand...
Click to collapse
I just did this. I didnt use that ADH* glue some people are talking about. I simply inspected how the old one is soldered on. Then removed the old one. There will be slight residue of the glue people are mentioning. I just simply took the solder tip OFF my soldering iron. then used a magnify glass to align the new ribbon. I also used clear tape to hold half of the ribbon down. Meaning i did 1 side at a time. So i taped from the middle to the far left to hold the ribbon down. I then used the blunt end of my soldering iron with the tip removed to press down with some force. Stayed in one location and counted to 20 the slid a little bit to the left. repeated this till the right 50% of the ribbon seemed glued down. I then applied clear tape over this portion and moved over to the previously taped left side. Repeating what I did on the right. after about 10 minutes of work. attached battery, press on button, phone came on. Then tested volume up and down and all worked.
lesterine said:
I just did this. I didnt use that ADH* glue some people are talking about. I simply inspected how the old one is soldered on. Then removed the old one. There will be slight residue of the glue people are mentioning. I just simply took the solder tip OFF my soldering iron. then used a magnify glass to align the new ribbon. I also used clear tape to hold half of the ribbon down. Meaning i did 1 side at a time. So i taped from the middle to the far left to hold the ribbon down. I then used the blunt end of my soldering iron with the tip removed to press down with some force. Stayed in one location and counted to 20 the slid a little bit to the left. repeated this till the right 50% of the ribbon seemed glued down. I then applied clear tape over this portion and moved over to the previously taped left side. Repeating what I did on the right. after about 10 minutes of work. attached battery, press on button, phone came on. Then tested volume up and down and all worked.
Click to expand...
Click to collapse
Can u explain me how u attached the flex cable back to its place. I didnt full understud this explanation. Have the same problem hoping u can help me.
using the soldering iron t shape tip, step 1 using the scraper to scrap away the glue then install the silicone strip to heat the flex cable on the board. hope this help.
Have same problem too! When I transferred the board with the power/volume button flex cable to a new housing, I accidentally lifted part of the flex cable causing my XZU C6833 not to boot up, no vibration and no screen image.
And can't seem to find any tutorial on how to properly attach the said cable onto the main board.
Will try lesterine's solution.