I have a htc evo 3D GSM device with
hboot 1.49.0007 and S-OFF
Yesterday i formatted the SD Card and i had some problems with it but i restored my stock rom through a nand backup
Today i had some problems while flashing SAD ICS ROM , i had clockworkmod recovery
I downloaded TWRP recovery and flashed it through clockworkmod
then i rebooted my phone to recovery and thats when my phone turned off and its refusing to turn on or charge (but Im sure that the battery is alive and the charger is not corrupt {i tried 4 different chargers })
I tried every single way on the internet but nothing works (i tried camera + power / i tried power for 15 secs without battery then putting battery back /i tried adb reboot-bootloader/i tried power+ vol down)
so i believe my device is BRICKED
please help me if there's anything i can try
and Thanks
i apologize for not having any help but did you try ..fastboot reboot? or adb reboot recovery? i will be checking this treat to get info for future problems
what does the phone do when u try to power on, and or when u vol down and power? also make sure u press vol down first then power. just a tip 3d buttons are not the best.
sksbri have
Efrencalvario said:
i apologize for not having any help but did you try ..fastboot reboot? or adb reboot recovery? i will be checking this treat to get info for future problems
Click to expand...
Click to collapse
i tried both , they didn't work
URnomig effectual
jblaze10 said:
what does the phone do when u try to power on, and or when u vol down and power? also make sure u press vol down first then power. just a tip 3d buttons are not the best.
Click to expand...
Click to collapse
the phone does nothing at all
Jaafarov said:
the phone does nothing at all
Click to expand...
Click to collapse
pull the battery out wait 10 seconds then put it back in ...now watch the red led light closely... try to turn th device on... does a faint red light appear then vanish? is so that is your phone trying to load the EMMC, kind of like the bios loading on a computer... if it does nothing after that youre most likely bricked... if you go to the CDMA development section for evo 3d';s there is a toolkit that you can use to unbrick your device...post back and let me know...also do not try the toolkit if youre a GSM phone...youll have to browse that section then for a tool to help you ...
wloftus said:
pull the battery out wait 10 seconds then put it back in ...now watch the red led light closely... try to turn th device on... does a faint red light appear then vanish? is so that is your phone trying to load the EMMC, kind of like the bios loading on a computer... if it does nothing after that youre most likely bricked... if you go to the CDMA development section for evo 3d';s there is a toolkit that you can use to unbrick your device...post back and let me know...also do not try the toolkit if youre a GSM phone...youll have to browse that section then for a tool to help you ...
Click to expand...
Click to collapse
No light appears at all
Did you ever figure it out?
Same thing happened to my phone this morning (I'm rooted, but still S-ON and hadn't tried anything lately). My battery was dying so I plugged it in on the car ride home, and when I stopped it was off and wouldn't turn on.
Related
Hi guys, I am feeling really nervous about this... So, the problem is, that I've just rooted my HTC GSM Hero and installed 2.2 ROM (http://forum.xda-developers.com/showthread.php?t=767886). Then I downloaded this app http://forum.xda-developers.com/showthread.php?t=892297. There I chose wrong icon (I didn't notice the icon was for FroydVillain) and rebooted device... Now I can't boot device into normal mode (it shows hero for a while, then turns into black screen, and nothing more happens) or recovery mode (it stucks when it shows HERO). I tried this: http://forum.xda-developers.com/showpost.php?p=4467471&postcount=13 but it didn't work. I'm a complete beginner. Any ideas? Is my device really bricked? THANKS.
Boot into recovery, reflash the room. I dont know why would you anything to spl...
Sent from my HTC Hero using XDA App
brat.haneq said:
Boot into recovery, reflash the room. I dont know why would you anything to spl...
Sent from my HTC Hero using XDA App
Click to expand...
Click to collapse
But I can't boot into recovery... That's the problem... It stucks when it shows HERO
matthew31 said:
Hi guys, I am feeling really nervous about this... So, the problem is, that I've just rooted my HTC GSM Hero and installed 2.2 ROM (http://forum.xda-developers.com/showthread.php?t=767886). Then I downloaded this app http://forum.xda-developers.com/showthread.php?t=892297. There I chose wrong icon (I didn't notice the icon was for FroydVillain) and rebooted device... Now I can't boot device into normal mode (it shows hero for a while, then turns into black screen, and nothing more happens) or recovery mode (it stucks when it shows HERO). I tried this: http://forum.xda-developers.com/showpost.php?p=4467471&postcount=13 but it didn't work. I'm a complete beginner. Any ideas? Is my device really bricked? THANKS.
Click to expand...
Click to collapse
Stay calm... it's not necessarily bricked yet
First thing i would like you to do is charge your phone to max!
Try and turn on the phone and hold to "On" key and "Home" key together for 60 seconds. If this doesn't boot you to recovery, try again one more time! It's happened to me that i didn't realise the button wasn't pressed all the way down.
If that doesn't work then let it boot as normal and even though it goes to the black screen don't panic.
Do you have any of the android tools installed?
http://forum.xda-developers.com/showthread.php?t=502010
See there for help on how to get adb up and running and then come back here.
Another thing i'm curious about while we're here... when you boot the device as normal.. connect it to power, the orange (or green) led at the top should be off for a few seconds while the hero boots up... when it goes to this black screen that you see.. does the light come on?
Bantu85 said:
Stay calm... it's not necessarily bricked yet
First thing i would like you to do is charge your phone to max!
Try and turn on the phone and hold to "On" key and "Home" key together for 60 seconds. If this doesn't boot you to recovery, try again one more time! It's happened to me that i didn't realise the button wasn't pressed all the way down.
If that doesn't work then let it boot as normal and even though it goes to the black screen don't panic.
Do you have any of the android tools installed?
http://forum.xda-developers.com/showthread.php?t=502010
See there for help on how to get adb up and running and then come back here.
Click to expand...
Click to collapse
OK, so, SDK is being installed now, and the phone is charging. What should I do next?
Bantu85 said:
Another thing i'm curious about while we're here... when you boot the device as normal.. connect it to power, the orange (or green) led at the top should be off for a few seconds while the hero boots up... when it goes to this black screen that you see.. does the light come on?
Click to expand...
Click to collapse
When my phone is off, the led is red. When I see that black screen, it is off... Is that bad??
Not necessarily.. it could just mean that it's not finishing it's boot up... let it charge for a while.
Your phone is most likely fine. You just confused it so it can't start up normally. We'll get you back in recovery mode and then you can reinstall your 2.2 rom.
Bantu85 said:
Not necessarily.. it could just mean that it's not finishing it's boot up... let it charge for a while.
Your phone is most likely fine. You just confused it so it can't start up normally. We'll get you back in recovery mode and then you can reinstall your 2.2 rom.
Click to expand...
Click to collapse
So I'll charge the phone the whole night, and I'll try booting it in recovery mode tomorrow morning - I will post the result here Thanks
yes.. if it boots into recovery mode (which it should!) wipe everything and reflash... that should sort you out.
Bantu85 said:
yes.. if it boots into recovery mode (which it should!) wipe everything and reflash... that should sort you out.
Click to expand...
Click to collapse
No, it unfortunately didn't boot.. I left it for an hour but it still didn't help.. I'll retry booting it, but anyway, any more ideas? Anyways, thanks.
Hi there
I'm assuming, that You know how to get into recovery, as You flashed a couple of things. Perhaps Your home key is broken
Question: do You have adb set up on Your computer? if yes - does it recognize Your phone ?
There is always option to run RRU...have You tried that ?
with regards
brat.haneq
have you tried booting holding VOLUME DOWN?
brat.haneq said:
Hi there
I'm assuming, that You know how to get into recovery, as You flashed a couple of things. Perhaps Your home key is broken
Question: do You have adb set up on Your computer? if yes - does it recognize Your phone ?
There is always option to run RRU...have You tried that ?
with regards
brat.haneq
Click to expand...
Click to collapse
Yes, I have ADB, but when I type adb devices, it only writes: "List of devices attached" (does that mean that it recognize my phone?)
I'm not sure I know what RRU is
bonesy said:
have you tried booting holding VOLUME DOWN?
Click to expand...
Click to collapse
Yes, it finds HEROIMG,zip, then loads it, then checks it, and adter that nothing happens - the phone still doesn't boot.
ok, volume down key response is good
ADB apears not to discover Your phone, probably drivers problem ;/
Look for RRU file it's used for factory reseting entire phone.
You can download it from HTC.com site.
With regards
brat.haneq
EDIT: go to htc.com site. look for downlaoding software for Your phone. You will have to provide Your imei. and You will receive .exe file - that You will have to run on Your PC. You can also look for it on this forum, they should be around here somewhere (or perhaps shipped roms.com)
brat.haneq said:
ok, volume down key response is good
ADB apears not to discover Your phone, probably drivers problem ;/
Look for RRU file it's used for factory reseting entire phone.
You can download it from HTC.com site.
With regards
brat.haneq
EDIT: go to htc.com site. look for downlaoding software for Your phone. You will have to provide Your imei. and You will receive .exe file - that You will have to run on Your PC. You can also look for it on this forum, they should be around here somewhere (or perhaps shipped roms.com)
Click to expand...
Click to collapse
When I enter the S/N in the htc.com site, it shows: Sorry, this software download is not suitable for your device. I can download it from xda forum, but will this work?
Maybe there's some way to flash my recovery img via hboot (POWER + VOLUME DOWN)?
Try downloading usbdeview HERE plug the phone in,turn it on,leave it for 10-15 seconds for windows to recognize it...load usbdeview and uninstall and delete anything with android,htc,mass storage or adb in it thats showing as connected (on the right hand side) unplug phone......then download and install HTC Sync HERE let it install,then reboot (to be safe) plug the phone in and let its do its business,DONT let windows search and direct it to program files/htc sync/drivers (or similar) you should then have adb! If you dont it could be a problem with your misc.img i had this with my magic and fixed it with a post on this forum but will post it up if the first bit doesnt work
Any troubles gtalk me [email protected]
matthew31 said:
Maybe there's some way to flash my recovery img via hboot (POWER + VOLUME DOWN)?
Click to expand...
Click to collapse
you have to do that with fastboot
I solved this problem! I just put the correct RUU in my sdcard and named it HEROIMG.zip and then turned on hboot - it flashed the RUU and now I got my phone alive! thanks for your help guys
Sent from my Hero using XDA App
After I root my device I try to install an offically rom but I didn't check my battery I open my device on the bootloader and I started installing the RUU rom it's gived me an error 130 up to now my device It was working then I pull the battery to open my devic normally but when I get back my battery inside my device and I try to start It doesn't work.
after that I checked the battery I found it too low I kept my device from yesterday on the charger but It doesn't work again. I don't know what's the problem. isn't device died or it's able to work again and what shall I do.
please help me
Ibrahim alkhuzai said:
After I root my device I try to install an offically rom but I didn't check my battery I open my device on the bootloader and I started installing the RUU rom it's gived me an error 130 up to now my device It was working then I pull the battery to open my devic normally but when I get back my battery inside my device and I try to start It doesn't work.
after that I checked the battery I found it too low I kept my device from yesterday on the charger but It doesn't work again. I don't know what's the problem. isn't device died or it's able to work again and what shall I do.
please help me
Click to expand...
Click to collapse
Do you get a charging led when you plug it into the wall? If no, then your battery is toast or you're bricked. what was the phone doing when you pulled the battery?
Sent from my PG86100 using Tapatalk
please help me
It was on the bootloader screen and it doesn't give me any error message I just want to remove the battery to open it normally to check the setting. after that I can't open it again. and when I connect it to charge the light of the charging lamp it doesn't work. but if I connect my device to the computer the computer read something abd when I open CMD and write adb devices it's show me that it's connected but If I write any another command it doesn't response.
Thank you for your help
Ibrahim alkhuzai said:
It was on the bootloader screen and it doesn't give me any error message I just want to remove the battery to open it normally to check the setting. after that I can't open it again. and when I connect it to charge the light of the charging lamp it doesn't work. but if I connect my device to the computer the computer read something abd when I open CMD and write adb devices it's show me that it's connected but If I write any another command it doesn't response.
Thank you for your help
Click to expand...
Click to collapse
If you don't get a charging light when plugged into the wall then you might indeed be bricked. I'm not sure what else you should try. No charge LED usually means it's a brick. Good luck, wish I had more help to offer sure ya.
Sent from my PG86100 using Tapatalk
Not sure exactly what you are saying but can you boot into bootloader at all?
Had similar problem with cwm ...my battery died yesterday ....when I got home and put it on charge it just wouldn't....so this morning took it to car phonewarehouse to change it they told me the battery was completely dead with no voltages in it. Maybe this can help solve cwm problem !
Sent from my HTC EVO 3D X515m using xda premium
Your battery may not be dead!
There is a known issue with GSM version on ClockworkMod Recovery, if you let the battery drain completely and the phone shuts down it will not charge even after a battery pull. The solution is to leave the battery out of the phone for 10 or 20 minutes and then put battery back into phone and boot into recovery with the volume & down power buttons. Once in recovery, let it charge for a half hour or so, then normal reboot. It has worked twice for me.
Hope this helps.
If your computer reads the phone in adb your not bricked. If you were bricked your phone wouldn't communicate with your computer at all. You probably just need another battery. Before doing that, see if you can boot in to recovery by pressing volume down (without letting it go), while repeatedly pressing the power button until it comes. If it doesn't come on try a new battery.
Just for future references, don't EVER pull battery while the bootloader is doing its thing. Once you "F" up your bootloader, your screwed. Then you'll definitely have a brick.
私の"DU4L C0R3 SH00T3Rは"³Dであなたを撃墜！トゥパックをねじ込みます 。
"AOSPのBACK!" ┌П┐[◣_◢]┌П┐
Xperia S Issues. Bad Flash
Hi, I read the 'existing users' installation instructions on the Sspeed ICS rom and installed the rom without installing the ics rom and kernel (I was tired). When booting, I go in a bootloop with the doomkernel screen. I can access recovery fine.
When holding vol+ and connecting to PC the phone goes back into it's bootloop and does not boot into fastboot.
When holding vol- and connecting to PC the phone flashes the green led and then boots into bootloop.
If I wait until the phone vibrates and lights up blue I can press the button to access recovery. I thought I could then just copy a gb rom over using USB mount but it is not detected on the PC.
Any help would be greatly appreciated.
Thank you
Try flashing stock ICS rom with flashtool
Sent from my LT26i using xda app-developers app
arc_u said:
Try flashing stock ICS rom with flashtool
Sent from my LT26i using xda app-developers app
Click to expand...
Click to collapse
Thanks but like I say fast boot and flashmode don't work so I can't access this option
I have the same problem too... I was hoping it would just work, but apparently it doesn't it needs a base rom.....I'm at work at the moment so i cannot fix my phone(i flashed it while at work which i shouldn't have done...) i noticed you can put it into fast boot in recovery - go to reboot options then fast boot can you see if that works
arc_u said:
Try flashing stock ICS rom with flashtool
Sent from my LT26i using xda app-developers app
Click to expand...
Click to collapse
unrealboot1 said:
I have the same problem too... I was hoping it would just work, but apparently it doesn't it needs a base rom.....I'm at work at the moment so i cannot fix my phone(i flashed it while at work which i shouldn't have done...) i noticed you can put it into fast boot in recovery - go to reboot options then fast boot can you see if that works
Click to expand...
Click to collapse
Hi thanks for your reply. I've tried going to fastboot
from recovery and I get a blue flashing light for one flash then it boots up again. Am I able to do anything at that point?
Glad I'm not the only stupid one on here
im not the expert here but I have bricked other phones before but never an xperia phone before. I have been reading up, the doom kernel has some mounting options, try to mount the sd card as mass storage so pc can send files accross to the phone. It should be mount and storage menu -> mount usb storage, then leave it on that menu and connect to computer, see if that works
unrealboot1 said:
im not the expert here but I have bricked other phones before but never an experia phone before. I have been reading up, the doom kernel has some mounting options, try to mount the sd card as mass storage so pc can send files accross to the phone.
Click to expand...
Click to collapse
Hi is this by the mount USB storage optuon ? I tried that and it wasn't detected on the PC. I could try another PC later. Recovery went into mount mode fine but nothing happened on the PC. Not even a blank drive which I know some people have had
If it blinks the LED for a second and reboots, that means that you don't have the drivers. Install drivers that are bundled with flashtool and try again. Or use Linux / OSX.
K900 said:
If it blinks the LED for a second and reboots, that means that you don't have the drivers. Install drivers that are bundled with flashtool and try again. Or use Linux / OSX.
Click to expand...
Click to collapse
I've used the laptop I'm trying it on for unlocking the boot loader and rooting. Maybe something corrupted the drivers. Will try on my Linux machine when I get home.
Thank you for all the help so far
Just Press VolUp and Power button until you get (one vibration followed by 3 consecutive vibrations) ... it will mean phone is shutdown.
Once shutted down, you will be able to press VolDown while plugging phone to PC and it will enter into flashmode.
Then you will be able to flash a FTF using flashtool
doesn't work...after the 3 beeps i let go and the screen turns black but then the boot loop happens again, i cant turn the phone off
Androxyde said:
Just Press VolUp and Power button until you get (one vibration followed by 3 consecutive vibrations) ... it will mean phone is shutdown.
Once shutted down, you will be able to press VolDown while plugging phone to PC and it will enter into flashmode.
Then you will be able to flash a FTF using flashtool
Click to expand...
Click to collapse
Hi, I do get the 3 vibrates and the phone stays off but instill got the individual quick flash then boot up.
Apologies mine stays off too, i just had it on charger so it turns on again after the 3 beeps, once off the charger it will turn off....I will be trying stuff when i get home.
Androxyde said:
Just Press VolUp and Power button until you get (one vibration followed by 3 consecutive vibrations) ... it will mean phone is shutdown.
Once shutted down, you will be able to press VolDown while plugging phone to PC and it will enter into flashmode.
Then you will be able to flash a FTF using flashtool
Click to expand...
Click to collapse
This will work, cause I had a similar issue a while ago
Good luck
depulle87 said:
This will work, cause I had a similar issue a while ago
Good luck
Click to expand...
Click to collapse
correct
Hello. I've got familiar problem. My phone blacked out after one day having about 35 % battery full. I was trying to reset it by holding power and volume up buttons - nothing happened. Just once showed up Sony logo but then again black nothing. Then it vibrate 3 times quickly and from that time it is shutted down, won't turn on even in flashmode. LED is not working too. I was asking for advice in local store servise and guy told me, that new phones have to be at least 30 min on the charger. So it's here now for hour, no result. :/
Just fixed this issue.
Follow these steps
1.hold vol up + power until phone vibrates 3 times.
2.open flash tool and point towards your stock file.
3.hit okay
4.wait for flash tool to prepare the files then it will prompt you to connect device in flash mode( vol down + power)
5.wait for it to finish. Unplug reboot and there you go fixed...
Hope this helps
Sent from my LT26i using Tapatalk 2
Cant do that, because PC dont recognize the phone. Phone has just red LED, thats all.
Alikalix said:
Cant do that, because PC dont recognize the phone. Phone has just red LED, thats all.
Click to expand...
Click to collapse
Use the bundled wallcharger!!! not a PC, pc has too less power to charge it now!
After wallcharger is placed hold vol+ and power for a few seconds until 3 vibrations, then let the phone on charger for atleast 2 hours, if all is good phone will bootup to the "charging animation"
Regards
Bin4ry said:
Use the bundled wallcharger!!! not a PC, pc has too less power to charge it now!
After wallcharger is placed hold vol+ and power for a few seconds until 3 vibrations, then let the phone on charger for atleast 2 hours, if all is good phone will bootup to the "charging animation"
Regards
Click to expand...
Click to collapse
Something similar happened to me. I have the bugged version of chargemon (only can charge with phone on) and accidentally discharged completely. The phone didn't boot, didn't charge and didn't do the 3 vibrations thing. So I put the battery off, conected the wall charger, putted the battery and it booted
It's really easy to remove the battery, you just need to be careful
My Amaze has been off for about a week or two and now it wont even power on.
If I press and hold the power button I get no indication that it is doing anything. However, if I press the buttons on the bottom of the screen I get a slight vibration indication that it is indeed getting power to it. Tried booting into recovery with no luck.
Any thoughts?
What recovery are you using? I know most recoveries don't support charging while off. I suggest 4EXT but you will need to charge the battery externally first in order to flash it. Good luck.
do you have an external battery charger to charge the battery out of the phone?
did you try to charge the battery ?
Here's an interesting update.
Was able to plug it in USB and using ADB restart into recovery. From recovery I hit restart and the phone booted up like normal.
BUT, about 5-10 seconds in Android it reboots again back to the black screen with the vibrating buttons. Had to run back to work so I wasn't able to play around with it anymore than that.
BiznessMan said:
Here's an interesting update.
Was able to plug it in USB and using ADB restart into recovery. From recovery I hit restart and the phone booted up like normal.
BUT, about 5-10 seconds in Android it reboots again back to the black screen with the vibrating buttons. Had to run back to work so I wasn't able to play around with it anymore than that.
Click to expand...
Click to collapse
if your running a custom rom maybe it got corrupted somehow, happens to my phone often due to the fact im trying to find a way around to cloning one rom to another phone, try to reset your phone back to stock by flashing a ruu stock rom or a different rom, flash 4EXT and wipe everything from the phone (including sd card) don't forget to check and realign the partitions and then toggle usb mode and put the rom on the sdcard and flash it , hope that helps
Ninjistix said:
if your running a custom rom maybe it got corrupted somehow, happens to my phone often due to the fact im trying to find a way around to cloning one rom to another phone, try to reset your phone back to stock by flashing a ruu stock rom or a different rom, flash 4EXT and wipe everything from the phone (including sd card) don't forget to check and realign the partitions and then toggle usb mode and put the rom on the sdcard and flash it , hope that helps
Click to expand...
Click to collapse
Thanks for the reply but I can't even get it to recognize via USB anymore
Buttons still vibrate, screen is still black. I can't get anything to work on it
BiznessMan said:
Thanks for the reply but I can't even get it to recognize via USB anymore
Buttons still vibrate, screen is still black. I can't get anything to work on it
Click to expand...
Click to collapse
Battery pull, hold volume down(or is it up? I work on too many android phones..) and power button and it should boot into bootloader. From there reboot into recovery. Flash a custom rom of your choice after doing a full wipe. Problem should be solved unless there is a hardware issue, at which point it must have been dropped, battery issue, etc..
What it really seems like is your battery doesn't have enough juice to sustain power, (I get bootloops when my battery goes really low and I try turning it on). Just let it charge a bit and if the battery isn't holding its charge, then time for a new battery
Sent from my Amaze using xda app-developers app
hey so i flashed the newest clean rom and tried to flash the logo menu button hack and after trying to reboot the screen is just blank. Any combination of buttons makes the bottom two buttons flash but nothing appears on the screen. Please tell me there is a fix for this. thanks guys
anybody?! ive tried using the RUU but my computer doesnt recognize the phone, it'll make a noise when i plug it in but wont recognize it
see what other people say...
but if nothing works out send it to HTC..i recently bricked my rooted ONE X ..could not find any answer on XDA and end up sending it to HTC..
came back working perfectly fine
i let the battery drain last night and plugged it back in and it showed the charging light. then i held the power button and the htc development software screen came on then it goes black again.
theres an mtp driving missing, if i can find that i think the ruu will work. ive downloaded the drivers from the tool kit and the htc sync manager but still no mtp driver found. any ideas?
thatg said:
anybody?! ive tried using the RUU but my computer doesnt recognize the phone, it'll make a noise when i plug it in but wont recognize it
Click to expand...
Click to collapse
thats a driver problem install the proper drivers and the RUU will work
Try
CheesyNutz said:
thats a driver problem install the proper drivers and the RUU will work
Click to expand...
Click to collapse
Try:
- Put your phone into fastboot mode : power + volume down
- Reinstall HTC driver, uninstall HTC syn
Goodluck
f6v8nf1 said:
Try:
- Put your phone into fastboot mode : power + volume down
- Reinstall HTC driver, uninstall HTC syn
Goodluck
Click to expand...
Click to collapse
Not sure why you quoted me lol
Sent from my METAL PHONE not some plastic phone bloated phone
so heres what i did, im not sure what i did when flashed the logo menu button kernel but it messed something up during the boot process and wouldnt let me use any button combo to fix it.
i let the battery drain, charged it up till i had a steady orange led light, held volume down + power and got into recovery and restored the backup i made before i flashed the kernel.
I'd still like to get the logo used as the menu button if anyone has been able to get this working on an AT&T htc one I'd appreciate being pointed in the right direction. thanks guys.
thatg said:
so heres what i did, im not sure what i did when flashed the logo menu button kernel but it messed something up during the boot process and wouldnt let me use any button combo to fix it.
i let the battery drain, charged it up till i had a steady orange led light, held volume down + power and got into recovery and restored the backup i made before i flashed the kernel.
I'd still like to get the logo used as the menu button if anyone has been able to get this working on an AT&T htc one I'd appreciate being pointed in the right direction. thanks guys.
Click to expand...
Click to collapse
Logo2menu works fine. I'm unlocked s-off and rooted and I've used it on almost every Rom I've tried. It's enabled at the kernel level. Find a rom you like, then find a supported kernel then flash it and usually most kernels flash from aroma and let you pick from a list of features. Here's my last tip. Go to the regular HTC one forums not att HTC one. No one really hangs around here. It's the same phone...
Sent from my HTC One using XDA Premium 4 mobile app