Related
Received a brand new Ace yesterday, and immediately rooted it with super one click with no problems.
However I then tried to run the 'Galaxy Ace Unlock apk' which I'd found elsewhere.
It generated an unlock pin, but after rebooting it stuck on the Galaxy Ace flash screen. After 5 minutes I pulled the battery out, waited, then rebooted. Now it doesn't even get to the Galaxy Ace screen when switched on.
The screen backlight comes on (with a black screen) for a couple of seconds, then off, then on - but it never gets any further.
So far I've tried
- Flashing Stock Froyo via Odin
- Flashing VillainRom via Odin
In both cases the phone enters download mode, Odin completes all steps without error, but on reboot I am left with the black screen of death again!
Anything else I could try?
I have the same problem.
Have you found a solution?
zongamin said:
Received a brand new Ace yesterday, and immediately rooted it with super one click with no problems.
However I then tried to run the 'Galaxy Ace Unlock apk' which I'd found elsewhere.
It generated an unlock pin, but after rebooting it stuck on the Galaxy Ace flash screen. After 5 minutes I pulled the battery out, waited, then rebooted. Now it doesn't even get to the Galaxy Ace screen when switched on.
The screen backlight comes on (with a black screen) for a couple of seconds, then off, then on - but it never gets any further.
So far I've tried
- Flashing Stock Froyo via Odin
- Flashing VillainRom via Odin
In both cases the phone enters download mode, Odin completes all steps without error, but on reboot I am left with the black screen of death again!
Anything else I could try?
Click to expand...
Click to collapse
Hey!
Dose you RESET FACTORY SETTINGS and FORMAT CACHE in recovery, before flashing with ODIN?
CHEERS!
Did the light lit when you entered the download mode? That's the indicator.
I got the same proble, tried several firmwares with odin but, when the phone reboots it starts flashing again
Hey!
You all, try THIS one.
CHEERS!
casiocas said:
Hey!
You all, try THIS one.
CHEERS!
Click to expand...
Click to collapse
I tried it, several times with different firmwares but it doesn´t do anything. The phone, when rebooting with odin, keeps flashing the black screen
moe_szislack said:
I tried it, several times with different firmwares but it doesn´t do anything. The phone, when rebooting with odin, keeps flashing the black screen
Click to expand...
Click to collapse
Hey!
Just wanted to ask, FROM WHERE you downloaded you UNLOCK soft. Can you give me the link? PLEASE!
CHEERS!
casiocas said:
Hey!
Just wanted to ask, FROM WHERE you downloaded you UNLOCK soft. Can you give me the link? PLEASE!
CHEERS!
Click to expand...
Click to collapse
Sorry if it sound rude, it wasn´t my intention.
I download the soft form samfirmwares.com.
Cheers
moe_szislack said:
Sorry if it sound rude, it wasn´t my intention.
I download the soft form samfirmwares.com.
Cheers
Click to expand...
Click to collapse
Ok, I get. But SORRY, then I cant help. You must contact then, from where you downloaded it.
Just I hope you get fixed your phone(If you most take it to SERVICE, try to explain them that you tryed RESET FACTORY SETTINGS. It work for several ppl-s here, who must take his phone to SERVICE). Just be 10 times SURE, that you cant flash or recovery you phone, or they can do the same and see that your phone WAS ROOTED or FLASHED the CUSTOM ROM(JUST BE SURE, THEY CANT ACCESS YOU PHONE or you lose you WARRANTY).
I hope all ENDS good! Fingers crossed for you phone!!!
CHEERS!
casiocas said:
Ok, I get. But SORRY, then I cant help. You must contact then, from where you downloaded it.
Just I hope you get fixed your phone(If you most take it to SERVICE, try to explain them that you tryed RESET FACTORY SETTINGS. It work for several ppl-s here, who must take his phone to SERVICE). Just be 10 times SURE, that you cant flash or recovery you phone, or they can do the same and see that your phone WAS ROOTED or FLASHED the CUSTOM ROM(JUST BE SURE, THEY CANT ACCESS YOU PHONE or you lose you WARRANTY).
I hope all ENDS good! Fingers crossed for you phone!!!
CHEERS!
Click to expand...
Click to collapse
I forgot to say that I put a sim card (from other country) inside the ACE to check if it was unlocked.
Can it be the problem?
moe_szislack said:
I forgot to say that I put a sim card (from other country) inside the ACE to check if it was unlocked.
Can it be the problem?
Click to expand...
Click to collapse
Hey!
I want to help you, REALLY, but a bout that queation, I CANT ANSWER, RIGHT NOW. DONT KNOW EXACTLY. SORRY!
I try to find answers tomorrow(we have here 23:27). Tomorrow to work.
CHEERS!
casiocas said:
Hey!
I want to help you, REALLY, but a bout that queation, I CANT ANSWER, RIGHT NOW. DONT KNOW EXACTLY. SORRY!
I try to find answers tomorrow(we have here 23:27). Tomorrow to work.
CHEERS!
Click to expand...
Click to collapse
Ok, Thank you
Need help screen just flashes and blinks..
Tried multiple rom flashes...odin says pass but the ph doesn't boot up
Sent from my SAMSUNG-SGH-I897 using XDA App
misterio_mr111 said:
Need help screen just flashes and blinks..
Tried multiple rom flashes...odin says pass but the ph doesn't boot up
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
The same thing happens to me, Anybody has any idea?
Just send it to the service center.
No other recovery method is know.
I have been in every forum arond for this kinda brick and there is no solution for YOU to do. Also there is absolutely no way for Samsung to see either say that after the first boot the battery went dead and it never started again. It will be covered by your warranty and brand new ace! Now dont go making stupid mistakes again hope i helped
Sent from my GT-S5830 using XDA App
Apk/sim bricked my phone.
Unlock Apk also bricked my phone in the same manner.
The app generating the code is not the problem on it's own, it's when you put the "other" Sim card in and reboot that does the damage.
I got a buzz when i could still get Download Mode and Odin gave me a PASS when i reflashed, but alas the phone never rebooted and it still flashed black at me.
I'm trying everything to bring it back to life before it goes to the Service Centre and i have to give them some blag as to why it's bricked.
Other than Download Mode i can get "Emergency Dload Mode"(ARM9) & RAMDUMP.
BLZBud said:
Unlock Apk also bricked my phone in the same manner.
The app generating the code is not the problem on it's own, it's when you put the "other" Sim card in and reboot that does the damage.
I got a buzz when i could still get Download Mode and Odin gave me a PASS when i reflashed, but alas the phone never rebooted and it still flashed black at me.
I'm trying everything to bring it back to life before it goes to the Service Centre and i have to give them some blag as to why it's bricked.
Other than Download Mode i can get "Emergency Dload Mode"(ARM9) & RAMDUMP.
Click to expand...
Click to collapse
I got the same problem and still nobody has found how to unbrick the phone.
I´ll keep searching
moe_szislack said:
I got the same problem and still nobody has found how to unbrick the phone.
I´ll keep searching
Click to expand...
Click to collapse
Even Samsung don't have an easy way to repair it, hence they replace the mainboard to fix the issue.
Hey guys.
I made a stupid error last night when I tried going from ICS CM9 back to ICS STOCK LPQ.
I forgot to wipe data and just wiped cache and dalvik cache.
The connection broke whilst flashing through ODIN and now I have a blank black screen and the phone won't turn on...((( (It does technically as when I try pressing the on button later on the phone would get hot - meaning its on but BLACK SCREEN)
I have tried taking the battery out for hours and putting it back in...nothing is working.
I don't know what to do...I'm in uni where I have fast wifi. Please help. Any advice would be grateful
EDIT:
Ok.
So usb jig arrived this morning. Ripped it open. Popped my sgsII from charger (fully charged I think!) took battery out - 15 secs
placed battery back in.
Inserted USBJIG. . .
. . .
. . . . BLACK SCREEN OF DEATH
Nothing....Still the same. No screen activity...sad...
only way is either JTAG or Samsung service center right?
I used to have yellow exclamation mark + 4 counts....but they can't see anything so they won't know right?
or did the usbJig work but just the fact that I can't see anything on the screen??
...sad I hated seeing noobs flashing phones improperly and crying when it got softbricked....well even though mine is a straight hardbrick i still feel sad....noob
update.
I've taken it to SSCentre on tuesday. I called them yesterday and they said they couldn't fix it over there and had it shipped somewhere else...is that bad?
it could take upto 2 weeks!!!!!!
I rememeber the engineers working on my friends Galaxy S last year and they didn't have to send it to somewhere else. (he had the soft brick 3 yellow logo icons) and didn't have the version where the download/recovery mode didn't work) The engineer just flashed it with latest stock sgs firmware (ignoring that csc was orange lol)
Maybe my flash was so impeccable I fried the motherboard? I'm one kick ass bricker....
dk206 said:
Hey guys.
I made a stupid error last night when I tried going from ICS CM9 back to Gingerbread Stock JVU.
I forgot to wipe data and just wiped cache and dalvik cache.
The connection broke whilst flashing through ODIN and now I have a blank black screen and the phone won't turn on...((( (It does technically as when I try pressing the on button later on the phone would get hot - meaning its on but BLACK SCREEN)
I have tried taking the battery out for hours and putting it back in...nothing is working.
I don't know what to do...I'm in uni where I have fast wifi. Please help. Any advice would be grateful
dk206
Click to expand...
Click to collapse
I'm assuming download mode and recovery also don't work when the device is powered off?
dk206 said:
Hey guys.
I made a stupid error last night when I tried going from ICS CM9 back to Gingerbread Stock JVU.
I forgot to wipe data and just wiped cache and dalvik cache.
The connection broke whilst flashing through ODIN and now I have a blank black screen and the phone won't turn on...((( (It does technically as when I try pressing the on button later on the phone would get hot - meaning its on but BLACK SCREEN)
I have tried taking the battery out for hours and putting it back in...nothing is working.
I don't know what to do...I'm in uni where I have fast wifi. Please help. Any advice would be grateful
dk206
Click to expand...
Click to collapse
Hmm have you tried getting into download mode to see if the device shows up in odin?
dk206 said:
Hey guys.
I made a stupid error last night when I tried going from ICS CM9 back to Gingerbread Stock JVU.
I forgot to wipe data and just wiped cache and dalvik cache.
The connection broke whilst flashing through ODIN and now I have a blank black screen and the phone won't turn on...((( (It does technically as when I try pressing the on button later on the phone would get hot - meaning its on but BLACK SCREEN)
I have tried taking the battery out for hours and putting it back in...nothing is working.
I don't know what to do...I'm in uni where I have fast wifi. Please help. Any advice would be grateful
dk206
Click to expand...
Click to collapse
If you can get into download mode then there is still hope. If you can't then your only option is either warranty repair of Jtag service. If download mode then works then just reflash using Odin.
You flash i9000XXJVU to your i9100 phone? So you need JTAG or do service. Your bootloader is totally dead
hiepgia said:
You flash i9000XXJVU to your i9100 phone? So you need JTAG or do service. Your bootloader is totally dead
Click to expand...
Click to collapse
Didn't even notice that XXJVU was an i9000 firmware.
To OP: Yup nothing to do, but send it in for repairs.
yeah sorry not JVU LPQ (I was getting mixed up with firmwares)
Yeah phone not going into download or recovery mode.
I think when I press the power button the phone does turn on but I get nothing but black screen....(the phone warms up)
So shall I order a JTAG to flash? or take it to repair centre?
Will they know I've been flashing this thing to death? Counter is on 4 at the moment..... so worried!
dk206 said:
yeah sorry not JVU LPQ (I was getting mixed up with firmwares)
Yeah phone not going into download or recovery mode.
I think when I press the power button the phone does turn on but I get nothing but black screen....(the phone warms up)
So shall I order a JTAG to flash? or take it to repair centre?
Will they know I've been flashing this thing to death? Counter is on 4 at the moment..... so worried!
Click to expand...
Click to collapse
Are u sure?
vol down+power+home button is download mode
Check it once again if it doesn't work...
maybe u can try some usb-jigg ?!
so you can come in to download-mode and then flash with odin =(
dk206 said:
ye
So shall I order a JTAG to flash?
JTag is not Samsung warranty its a paid for service .
or take it to repair centre?
Will they know I've been flashing this thing to death? Counter is on 4 at the moment....
.
Warranty is void with custom rom root or rom counter above zero .
Will they know yes counter is on 4 .
Will they ignore it and put it through as warranty they may but dont count on it .
USB jig would be the starting point .
That fails you could go to warranty repair if thats rejected then pay for JTag repair .
jjue
Click to expand...
Click to collapse
Any place or website where I could buy a USB JIG?
Not really keen with solders....
Thanks guys
dk206 said:
Any place or website where I could buy a USB JIG?
Not really keen with solders....
Thanks guys
Click to expand...
Click to collapse
eBay. Or Google.
first charge it. Then try to enter download mode again. I have exp. 1 time battery low and phone just warm up and black screen. After Charge, it's ok till now!
dk206 said:
Any place or website where I could buy a USB JIG?
Not really keen with solders....
Thanks guys
Click to expand...
Click to collapse
Read the post USB jigs to loan out
http://forum.xda-developers.com/showthread.php?t=1495867
jje
if you have adb maybe you could try:
1. Connecting your device to PC while turned off,
2. CMD > adb devices
* If you see your device connected, proceed with:
adb reboot recovery or adb reboot bootloader
* If you don't see any device connected, try googling for qhsusb_dload driver for your device, and after you install them (and maybe a couple of PC restarts) repeat step 2
3. if you manage to get to recovery, i hope you have your nandroid backup so you could restore them.
my HTC sensation 4G had this situation few days ago, couldn't go to recovery/bootloader, blanked out when turned on and had fever
i fixed it using those steps, i wish i could remember where i got the qhsusb driver thingy from.. i'll let you know when i remember.
edit: it might work on S2, or might not.. i don't know this will help or not, but you could read adb/fastboot/bootloader/android 101, maybe you could get something from there
hiepgia said:
You flash i9000XXJVU to your i9100 phone? So you need JTAG or do service. Your bootloader is totally dead
Click to expand...
Click to collapse
The bootloader death thing is not 100% true. When I first got my phone, (when there wasn't any rom for it) I tried flashing a I9000 rom. I was so stupid and luckily it didn't break my phone. After the flashing it turned on and stayed on bootlogo.
It was a miracle for me!
Ok.
So usb jig arrived this morning. Ripped it open. Popped my sgsII from charger (fully charged I think!) took battery out - 15 secs
placed battery back in.
Inserted USBJIG. . .
. . .
. . . . BLACK SCREEN OF DEATH
Nothing....Still the same. No screen activity...sad...
only way is either JTAG or Samsung service center right?
I used to have yellow exclamation mark + 4 counts....but they can't see anything so they won't know right?
or did the usbJig work but just the fact that I can't see anything on the screen??
...sad I hated seeing noobs flashing phones improperly and crying when it got softbricked....well even though mine is a straight hardbrick i still feel sad....noob
You just got to hope for the guy that repairs it not to see or not to care about custom roms etc .
jje
JJEgan said:
You just got to hope for the guy that repairs it not to see or not to care about custom roms etc .
jje
Click to expand...
Click to collapse
Ok update.
I've taken it to SSCentre on tuesday. I called them yesterday and they said they couldn't fix it over there and had it shipped somewhere else...is that bad?
it could take upto 2 weeks!!!!!!
I rememeber the engineers working on my friends Galaxy S last year and they didn't have to send it to somewhere else. (he had the soft brick 3 yellow logo icons) and didn't have the version where the download/recovery mode didn't work) The engineer just flashed it with latest stock sgs firmware (ignoring that csc was orange lol)
Maybe my flash was so impeccable I fried the motherboard? I'm one kick ass bricker....
you should have tried download mode blindly first. as i have flashed once blindly and it fixed my all dead screen.
Hi there,
Firstly sorry if I have posted in the wrong place, i'm not too good with forums and or technology. About two weeks ago, my sister had passed me down her old Samsung Galaxy S2 which she had been using for more than a year. She's had no problems with it what so ever. Up until today, I was browsing the internet, when the internet 'app' crashed and gave me a pop up saying 'internet browser has stopped responding' or something to that affect. It then followed by a black screen where I was not able to do nothing apart from stare at the screen. I popped out the battery, waited a couple of minutes and put it back in. The screen came on with the Samsung logo, but nothing happened from there on, it was frozen. So I repeated the process one more, and now the phone does not turn on at all! I really hope someone can help me out here.
The phone has never been rooted/flashed or had anything done with it.
I have tried leaving the battery out for a couple of hours, still nothing.
I've also swapped batteries and nothing happened.
Tried booting in recovery/download mode and nothing happened either.
I've also tried connecting it to my PC where nothing happens.
I'm hoping someone can help me here, I've only had the phone for two weeks and it's already broken! My sister had it for a year and no problems! Bump.
Thanks in advance,
So can you boot into recovery or download mode? Without either of those two there's nothing you can do apart from take it to a service centre. If you have download mode then you can flash a stock ROM using Odin.
Else, do you have warranty still as it's a year old? If you do, take it to the service centre under warranty.
Sent from a galaxy far, far away
Tried a Jig to see if it enters Download mode?
"To err is human, to forgive is divine."
Sent from my SGS II
make sure ur battery points are not loose .. recently a user tried everything and lastly came to know that the 3 points were loose...
Man calm down try d combi 1st
Keep power home n vol up pressed it'll switch on then off then wil boot in recovery keep it pressed til it boots in rcvry.
Try dis n post will b helpful for helping
Hit thanks if I helped u
A click for u but rep for me
Sent from my Rooted LT26i using xda premium
Hopper8 said:
So can you boot into recovery or download mode? Without either of those two there's nothing you can do apart from take it to a service centre. If you have download mode then you can flash a stock ROM using Odin.
Else, do you have warranty still as it's a year old? If you do, take it to the service centre under warranty.
Sent from a galaxy far, far away
Click to expand...
Click to collapse
Hi, no I can't boot in to download more or recovery mode, and the phone is out of warranty.
Thanks anyway.
immortalneo said:
Tried a Jig to see if it enters Download mode?
"To err is human, to forgive is divine."
Sent from my SGS II
Click to expand...
Click to collapse
Sorry if I sound like a noob, but what is a jig?
Thanks
Are you sure it's out of warranty? Samsung offers a 2 year warranty in some countries (afaik everywhere in the EU)
My Wife says I'm a phone geek.....
I'd have to agree.....
Click the link in my signature and look at the section for 'no download mode'.. Try that section. Some users report being able to boot into download mode after trying those things.
Edit: And look on eBay for 'i9100 usb jig'. Its a way of attempting to force into download mode
Sent from a galaxy far, far away
Hopper8 said:
Click the link in my signature and look at the section for 'no download mode'.. Try that section. Some users report being able to boot into download mode after trying those things.
Edit: And look on eBay for 'i9100 usb jig'. Its a way of attempting to force into download mode
Sent from a galaxy far, far away
Click to expand...
Click to collapse
Thanks for the quick reply, unfortunately none of those methods worked for me, i'll try the USB jig and report back. If that doesn't work i'm guessing the motherboard is the problem right? Is Samsung able to repair the phone for me even if its out of warranty but with a cost? If so, how much do you think it will cost?
Thanks
You tried all of them in 15 minutes? Give them another go, it can take a few goes sometimes if you don't get it quite right. Otherwise, yes try the jig, but don't pin your hopes on it. Yes, they can repair it. The other (cheaper) option is to buy a handset with broken screen off eBay or similar and switch your motherboard. I'm sorry, I don't know the costs :/
Sent from a galaxy far, far away
Hopper8 said:
You tried all of them in 15 minutes? Give them another go, it can take a few goes sometimes if you don't get it quite right. Otherwise, yes try the jig, but don't pin your hopes on it. Yes, they can repair it. The other (cheaper) option is to buy a handset with broken screen off eBay or similar and switch your motherboard. I'm sorry, I don't know the costs :/
Sent from a galaxy far, far away
Click to expand...
Click to collapse
A little solution
Plug in ur usb to the PC as the device is off....it should remain off for this...
Plug in and see if its charging via pc.....As for it to charge..it has to go through the repair which happens internally without you need to do anything...
A triangle should appear before charging icon appears..As it appears,, just right after that flash ur rom via odin disconnect dont boot now wait n again do the usb charging trick.....
Then boot it should probably be working up again..Well it worths for a try.......
Do it n post it.
Tried rooting my s2 using odin. went into download mode then connected the phone. and clicked start. according to the instructions for rooting from youtube , it said the phone would restart after it said PASS on Odin. After it showed PASS it didnt restart even after a very longtime. so i disconnected.
Now i get the samsung logo with a triangle below. I m able to go to download mode.
Pls help guys
vixter991 said:
Tried rooting my s2 using odin. went into download mode then connected the phone. and clicked start. according to the instructions for rooting from youtube , it said the phone would restart after it said PASS on Odin. After it showed PASS it didnt restart even after a very longtime. so i disconnected.
Now i get the samsung logo with a triangle below. I m able to go to download mode.
Pls help guys
Click to expand...
Click to collapse
Did you check the AUTO REBOOT option in Odin? Did you try to remove the battery for a couple of minutes and reboot?
Yellow triangle is normal
PLEASE READ THE FAQ said:
Q4: When I turn my phone on, I see a yellow triangle. What is it and how can I get rid of it?
It will appear if you have flashed a non-official kernel from download mode. If you flash kernels using CWM recovery, Mobile Odin etc. you won't get this yellow triangle.
The easiest ways to remove it are to use the app Triangle Away OR use a USB Jig.
Click to expand...
Click to collapse
Aello said:
Did you check the AUTO REBOOT option in Odin? Did you try to remove the battery for a couple of minutes and reboot?
Yellow triangle is normal
Click to expand...
Click to collapse
yes auto reboot was checked. and i did remove the battery. What else can i do ?
ADDICT.ANK said:
Man calm down try d combi 1st
Keep power home n vol up pressed it'll switch on then off then wil boot in recovery keep it pressed til it boots in rcvry.
Try dis n post will b helpful for helping
Hit thanks if I helped u
A click for u but rep for me
Sent from my Rooted LT26i using xda premium
Click to expand...
Click to collapse
Hi there:
I had bought the device in June 2011
I had the same problem about 7 months back and did as you suggested, was able to recover the firmware.
Now, I am facing the same problem today, my device started and was stuck on the Samsung Galaxy S2 logo.
Did the same thing again, the animated android logo appeared, and after some time the device was off.
I have been trying to get the device to switch on , but to no avail, the device is not even powering ON.
Device info: Unrooted , OS: 4.1.2
Please advice. Kindly treat this as urgent.
Many thanks in advance.
Best regards,
Siddharth
sharma_sid said:
I have been trying to get the device to switch on , but to no avail, the device is not even coming to (switched off)
charging mode
Click to expand...
Click to collapse
Phone not booting at all/charging/no signs of life = Samsung service centre or local mobile repair shop for diagnosis. Nothing anyone here can suggest beyond that if the phone won't even bootloop or be in a state where it's 'user fixable'.
sharma_sid said:
Hi there:
I had bought the device in June 2011
I had the same problem about 7 months back and did as you suggested, was able to recover the firmware.
Now, I am facing the same problem today, my device started and was stuck on the Samsung Galaxy S2 logo.
Did the same thing again, the animated android logo appeared, and after some time the device was off.
I have been trying to get the device to switch on , but to no avail, the device is not even powering ON.
Device info: Unrooted , OS: 4.1.2
Please advice. Kindly treat this as urgent.
Many thanks in advance.
Best regards,
Siddharth
Click to expand...
Click to collapse
Sorry For the late reply.
I guess, you need to boot in recovery
with home + power+vol up
and clear data and reboot
if that doesnt help.
try booting in download mode again and flash the firmware.
but let it charge first.
and post here
ADDICT.ANK said:
Sorry For the late reply.
I guess, you need to boot in recovery
with home + power+vol up
and clear data and reboot
if that doesnt help.
try booting in download mode again and flash the firmware.
but let it charge first.
and post here
Click to expand...
Click to collapse
Tried everything , the phone is not even powering ON.
I checked with service center , they are asking INR 8000 to replace the motherboard.
I'm instead thing of buying S4, should I ?
please advice guys.
My phone is dead too...
I left it on (functioning normally) and went for a bath, when I got out it was dead...
From functioning ok to nothing in a few minutes, I don't have any idea why. Is it really the motherboard?
Fact: Electronics breaks. All the time. All electronics.
MJDdeLacerda - Take it to a local mobile repair shop for diagnosis, unless you're experienced with this type of electronics, nothing you can do.
Hey guys,
I have a galaxy s3 (I9300) and I've had it rooted for some time now. I started using CyanogenMod 10.2 nightlies a few months ago and they've mostly been fine. The odd issue comes up but I've been able to work it out. So, a few hours ago my phone just turned off of its own accord and started to bootloop, but on the "Samsung Galaxy S3 GT-19300" screen, not the CyanogenMod screen (to clarify, this screen comes up first then the cyanogenmod one usually). I've tried booting into recovery (CWM 6) but it just shows the CWM boot logo thing (that cog with the hat) and then loops back to the galaxy s3 page. I've also tried putting it in download mode, and it seems to stay on the warning page longer than it does anywhere else, but it wont let me actually put in it download mode from there.
I had a look around google and saw people have had the same problem, but everything I could find was when people had flashed a new rom/kernel etc. and something had gone wrong in the process. The weird thing about mine is that I haven't changed anything, even downloaded any new apps, for maybe a week, so it's not like something suddenly changed. I also wasn't using it when it started, it was just sitting on the table next to me.
Usually I can work these things out, but I'm stumped here. Any help would be really appreciated.
Thanks in advance!
danielbollom said:
Hey guys,
I have a galaxy s3 (I9300) and I've had it rooted for some time now. I started using CyanogenMod 10.2 nightlies a few months ago and they've mostly been fine. The odd issue comes up but I've been able to work it out. So, a few hours ago my phone just turned off of its own accord and started to bootloop, but on the "Samsung Galaxy S3 GT-19300" screen, not the CyanogenMod screen (to clarify, this screen comes up first then the cyanogenmod one usually). I've tried booting into recovery (CWM 6) but it just shows the CWM boot logo thing (that cog with the hat) and then loops back to the galaxy s3 page. I've also tried putting it in download mode, and it seems to stay on the warning page longer than it does anywhere else, but it wont let me actually put in it download mode from there.
I had a look around google and saw people have had the same problem, but everything I could find was when people had flashed a new rom/kernel etc. and something had gone wrong in the process. The weird thing about mine is that I haven't changed anything, even downloaded any new apps, for maybe a week, so it's not like something suddenly changed. I also wasn't using it when it started, it was just sitting on the table next to me.
Usually I can work these things out, but I'm stumped here. Any help would be really appreciated.
Thanks in advance!
Click to expand...
Click to collapse
can you at least enter download mode after a long time you said? if not, try pulling out the battery for 5 minutes or more and re-insert and enter download mode. i hope it's not sds! good luck
sriram231092 said:
can you at least enter download mode after a long time you said? if not, try pulling out the battery for 5 minutes or more and re-insert and enter download mode. i hope it's not sds! good luck
Click to expand...
Click to collapse
Nope, if I press the volume up button to go into it, it just goes back to the bootloop. I'll try the battery thing though, thanks!
Nope, it didnt work, I left it out for maybe half an hour and nothings changed :/ anyone else got any ideas?
SDS thread and BootLoop identical questions posted .
What does Product Code say in download mode .
But if you cannot get to download mode then you need a service centre repair .
looks like u are facing SDA but a bit diffrend than a normal SDS.. mine still can go into download mode with blank product name..
If product name is blank in download mode then you got sudden death, consider a phone as a brick. Nothing will help, including repartitioning.
You need to contact service centre.
I'll check it in a minute, but if it is bricked, will any service center actually help me seeing as it's rooted and all?
danielbollom said:
I'll check it in a minute, but if it is bricked, will any service center actually help me seeing as it's rooted and all?
Click to expand...
Click to collapse
AFAIK if it's sudden death then it's not possible to detect root and other modified things, or in other words - nobody has money to prove that you have been using unofficial firmware .
JustArchi said:
AFAIK if it's sudden death then it's not possible to detect root and other modified things, or in other words - nobody has money to prove that you have been using unofficial firmware .
Click to expand...
Click to collapse
Ahhhh, well that is handy then
In terms of a service centre, will samsung have a list of them somewhere so I can find one near me?
So I contacted samsung and they gave me the link to book into a service centre etc, but I just realised that when I try to go into recovery mode, the CWM recovery logo comes up before going back to bootloop. Is there any way to get rid of that so that my root is completely untraceable?
danielbollom said:
So I contacted samsung and they gave me the link to book into a service centre etc, but I just realised that when I try to go into recovery mode, the CWM recovery logo comes up before going back to bootloop. Is there any way to get rid of that so that my root is completely untraceable?
Click to expand...
Click to collapse
If you can't flash anything with Odin (stock software) then you're screwed. Eventually you can try to enter recovery and flash "eraser" of recovery, but this requires working recovery... So if you actually can enter recovery then you can also flash anything, which will literally delete everything.
In other case, no, no way. But if you're lucky enough you may break it just by leaving your phone on for some hours in bootloop, haha.
JustArchi said:
If you can't flash anything with Odin (stock software) then you're screwed. Eventually you can try to enter recovery and flash "eraser" of recovery, but this requires working recovery... So if you actually can enter recovery then you can also flash anything, which will literally delete everything.
In other case, no, no way. But if you're lucky enough you may break it just by leaving your phone on for some hours in bootloop, haha.
Click to expand...
Click to collapse
Is there any way to wipe it with magnets or anything? hahah I'm clutching at straws now, but otherwise I'm just left with an expensive paperweight so I'm trying to find anything I can
danielbollom said:
Is there any way to wipe it with magnets or anything? hahah I'm clutching at straws now, but otherwise I'm just left with an expensive paperweight so I'm trying to find anything I can
Click to expand...
Click to collapse
To be honest think twice before physically crashing your internal memory, as it may void your warranty at all.
I'd try flashing stock firmware through odin, if it doesn't work I'd try flashing anything through recovery. If both of these methods fail just leave your phone in bootloop and hope that it'll automatically destroy everything... :laugh:
Seriously though, you can either physically destroy internal memory or leave it in bootloop and hope for the best, eventually send them device in current status. Up to you, because you won't have a possibility to do anything else.
JustArchi said:
To be honest think twice before physically crashing your internal memory, as it may void your warranty at all.
I'd try flashing stock firmware through odin, if it doesn't work I'd try flashing anything through recovery. If both of these methods fail just leave your phone in bootloop and hope that it'll automatically destroy everything... :laugh:
Seriously though, you can either physically destroy internal memory or leave it in bootloop and hope for the best, eventually send them device in current status. Up to you, because you won't have a possibility to do anything else.
Click to expand...
Click to collapse
If I send it back to them as it is now it'll take them about 20 seconds I reckon before they see the CWM logo, realise its rooted and send it straight back, so I dont know what I'm gonna do hahah
Uploading....Coming soon
Hello everyone this is the official odin package for the galaxy mega ATT version. With this you can get your phone back working if you get the "This phone is not running authorized software crap. " etc . Also hope it encourages more people to find a root method without the fear of having a brick. As many of you know this package was nowhere to be found so I had to bribe a Samsung employee to give it to me which means it wasn't free for me but I'm sharing it with you guys so if you send me a beer my way i'll be happy not mandatory.
This package is in multiple parts:
I527UCUBNE7
AP: Must be flashed under PDA in Odin. This is the biggest file and contains your system,recovery and kernel partition Download
BL: This is the bootloader. If you already took the update ignore this but if you want to upgrade your phone you must flash this Download
CP: This is the modem and other network related partitions. You must flash this under Phone in odin Download
CSC: This contains carrier related settings for our firmare. Flash this under CSC in odin. Download
Highly Recommended to perform a factory reset after the flashing is completed. Let me know your results
Omg !! Super thanks bro !!!! =))))))))
So good !!!!! update successfully
Thanks again !!!
so the guys that have tried this can confirm that is working!
and also liked to know how root is being dealt with
latinohot said:
so the guys that have tried this can confirm that is working!
and also liked to know how root is being dealt with
Click to expand...
Click to collapse
Garack has been working on it and has actually posted a file to flash in Odin I beleive. He say that if it boots up, then root should be obtainable.
Not sure anyone has tried it yet.
It is in the "root bounty for 4.4.2 update" thread
Sent from my SAMSUNG-SGH-I527 using XDA Free mobile app
im getting error last stage on system upload any advised ?
@ Sunderwear Thank you very much for the great post and instructions. I'm currently testing it out with my i527 AT&T with ODIN 3.09... will post results in a few minutes. My phone was stuck in reboot after official 4.4.2 AT&T update left it in loop mode... give me a few minuytes and I'll post my results!
Too close. I did all the steps, and indeed it passed all Odin steps (picture), but it's still stuck in loop mode. When I try to go into Recovery mode (Vol + and HOME), it will only show the blue letters on top of the screen (picture), then it reboots on its own... no fix do you know a possible fix for loop mode.
If I go to Odin mode (Vol - and HOME), this is what I got (picture)...
alex852 said:
Too close. I did all the steps, and indeed it passed all Odin steps (picture), but it's still stuck in loop mode. When I try to go into Recovery mode (Vol + and HOME), it will only show the blue letters on top of the screen (picture), then it reboots on its own... no fix do you know a possible fix for loop mode.
If I go to Odin mode (Vol - and HOME), this is what I got (picture)...
Click to expand...
Click to collapse
Has your phone been repaired.. Like a broken screen recently? And if it fails with the red letters at system upload. M. Try again with a different USB cord or port. I own a cellphone repair shop and have been using the files with no problems
Sunderwear said:
Has your phone been repaired.. Like a broken screen recently? And if it fails with the red letters at system upload. M. Try again with a different USB cord or port. I own a cellphone repair shop and have been using the files with no problems
Click to expand...
Click to collapse
Yeah, the screen was replaced a while ago. The phone went bad once it installed the 4.4.2 official update. I will try use some other usb cable. I have plenty of microusb wires. Do you think the screen has something to do with it?
Sunderwear said:
Has your phone been repaired.. Like a broken screen recently? And if it fails with the red letters at system upload. M. Try again with a different USB cord or port. I own a cellphone repair shop and have been using the files with no problems
Click to expand...
Click to collapse
Ok, I used a different port using also a brand new official/original Samsung MicroUSB cable to retest it. :crying: no work, again stuck in loop mode. Tomorrow, I will get another computer to retest this with another one. Will post the results tomorrow.
When the phone loops, I do not have any letters that appear anywhere besides the Samsung Galaxy Mega logo. it just vibrates, and then it restarts without showing any messages/letters.
You mentioned "Red letters at System Upload" is that when I hold Vol - and home? because I only get the blue letters if I do the Vol+ and home.
Thank you for your patience man. I'm sort of a noob, well, not sort of!
I haven't tried this yet...but I will back up tomorrow and report back how it goes with my unit...I still have my factory with no knox bootloader so far..and was debating if I want to even try really...
alex852 said:
Ok, I used a different port using also a brand new official/original Samsung MicroUSB cable to retest it. :crying: no work, again stuck in loop mode. Tomorrow, I will get another computer to retest this with another one. Will post the results tomorrow.
When the phone loops, I do not have any letters that appear anywhere besides the Samsung Galaxy Mega logo. it just vibrates, and then it restarts without showing any messages/letters.
You mentioned "Red letters at System Upload" is that when I hold Vol - and home? because I only get the blue letters if I do the Vol+ and home.
Thank you for your patience man. I'm sort of a noob, well, not sort of!
Click to expand...
Click to collapse
No worries. I was asking because the same happened to me with a customers phone..got screen replaced..then he took the 4.4.2 ota update..got stuck at samsung logo bootloop..i loaded the firmware like 4 times..re partition with pit file and erase all nand...I would get stuck in the same screen saying entering recovery..So it's an issue going around. Last resort would be sending it to Samsung
Sunderwear said:
No worries. I was asking because the same happened to me with a customers phone..got screen replaced..then he took the 4.4.2 ota update..got stuck at samsung logo bootloop..i loaded the firmware like 4 times..re partition with pit file and erase all nand...I would get stuck in the same screen saying entering recovery..So it's an issue going around. Last resort would be sending it to Samsung
Click to expand...
Click to collapse
Yes Sunderwear that will happen because there is 3rd parties making aftermarket screens and people were buying them as replacements...If you don't have the OEM screen the driver in the firmware won't work and it will hang...I run in to something like this on a Galaxy S4 I repaired...
alex852 said:
Too close. I did all the steps, and indeed it passed all Odin steps (picture), but it's still stuck in loop mode. When I try to go into Recovery mode (Vol + and HOME), it will only show the blue letters on top of the screen (picture), then it reboots on its own... no fix do you know a possible fix for loop mode.
If I go to Odin mode (Vol - and HOME), this is what I got (picture)...
Click to expand...
Click to collapse
check your AP files size that was happen to me i download file wan;st complete than i download again and make sure file download complete
and after that use odin don;t need other file just select on PDA and let odin run after that every thing will bee fine
I ran it as instructed and it worked flawlessly. tHANKS [email protected]
Help!
Every time I try to use the PDA and PHONE files, it says they have an invalid md5 hash. I've tried re-downloading them, but to no avail. Could anyone help with this?
thanks.it works fine...
I did all the stepa and finally I have K.K. Just wanted to say- thank you.
USMAN_ZEESHAN said:
check your AP files size that was happen to me i download file wan;st complete than i download again and make sure file download complete
and after that use odin don;t need other file just select on PDA and let odin run after that every thing will bee fine
Click to expand...
Click to collapse
Sorry for the long delay. I think I found the full issue with the Samsung Glaxy Mega boot loop on 4.4.2
My phone is till not working. We own four 6.3 Megas (1 my wife, 1 daughter, 1 son, and mine).
Officially I have 2 that are not working properly and stuck on boot loop. My wife and daughter are working properly on 4.4.2 my son's now and mine are stuck in boot loop. Wife's phone has original screen and it's working properly, my daughter has a replacement screen I bought on ebay for about $160.00 on January. My son's I've replaced the screens about 3-5 times already (a ton of money wasted), and mine, recently I did replaced it on May (before the 4.4.2 update on June). Here goes the issue:
My son's phone updated today about 2 hours ago while we were visiting the AT&T store for U-Verse Quote. Did not know it updated until we got home... Sons' phone is stuck in boot loop also now!!!!!!!!!!!! What I did was I took my daughters phone apart (with expensive replacement screen and currently running 4.4.2), and installed the screen on my sons and then mine, and each phone would work flawlessly with that screen, so I took the current replacement screens I had from my phone and my son to install them on my daughter's and each one would go into boot loop.
After that, I re installed the good screen on my daughters back, and daughters work properly again. I guess the generic OEM screens from eBay I've been buying for $50 bucks are not compatible with 4.4.2 Kitkat, they are only compatible with 4.2.2 Jelly bean.
Anyone knows where I can buy original screens? I've contacted several sellers on eBay to see if the screens work on 4.4.2 because I don't want to spend more money on screens. I just got 1 from China 2 days ago, and that one also gets stuck in boot loop... so frustrated with screens. All my OT from work goes to pay for these issues... Help anyone? Anyone sells working 4.4.2 compatible screens?
Also, I will buy a broken ORIGINAL screens from ebay (like $7-$10) to test it out and verify. I will post results. Hope this experiment (and my sadness) will help you guys out if stuck in boot loop.
P.S. Oh yeah, I did do both phones on PDA, then all BL,PDA, etc... and I still get boot looped. I have to say THANK YOU to the original autheor because it does work! It's just my screens that doesn't work!!!!! HELP GUYS!!!!!:crying:
Is there a certian order u need to flash these in?
Any short tutorials..
Ive flashed odin pda only b4..
Have to factory reset first?
Thanks guys.