Guys i need some help.
I was running the leaked JB OTA, but when i saw the MIUI, i tried to install it by overwriting safestrap over BMM. i could use safestrap but when i boot the rom, i get stuck with a blank screen.
after a bit of research i think i might have messed stuff by running ics on JB kernel.
Now im stuck, So if someone can please help....
Thnx in advance.
Edit:
Tried to install with fastboot, now everything is messed up, while flashing, it shows that recovery- partitions doesnt exist
Related
Guys I need help now please! I rooted, unlocked bootloader and followed a guide to install 2.3.4 on my Orange UK Atrix. First off it woiuld just flash the boot screen. But then I found out that i hadn't flashed a boot img and didn't know what tegra I was so I flashed both witha reboot ebwteen. Now it doesn't flash. I can access rsdlite and fastboot and have tried flashing an sbf I used in the root guide or whatever. EUGH THANKS
Fixed. Flashed a rom/kernel from recovery. Access it by holding volume down and power, then scrolling through options with down. Then press up on recovery.
Im assuming you already know this but make sure with every ROM flash / recovery change / kernel change you wipe things properly or things from the previous ROM could bleed through. And that will cause problems. Good luck, and have fun
I'm in the same boat , i installed the French SBF 2.1.1 , then rooted , and then i tried to go back to stock bell 2.2.2 but wont install
Well I'm now stuck on the boot screen again after trying getting Alien on there, but now trying something different and not even able to get that! Also, what's this fruitcake thing? It doesn't seem to help. Going to flash completely stock and start over after work! Flashing a 2.2.2 UK Orange sbf should be fine right? Thanks.
ok so i wouldnt say im a noob but im not as advanced as some of yous. last night i flashed a leaked ics onto my phone and loved it with one exception. i couldnt figure out how to root it. all my apps are backed up on titanium backup and i didnt want to have to get all of them manually. so i flashed back to stock using odin with a file i used back when that crappy update came out. i rooted it with super one click and and then went to put on a prerooted ics... when in recovery mode now i get this message
cant access to '/system/csc/att/system/'
i try putting on cwm and siyah and i keep getting authentication errors and the installation aborts. also recovery mode wont read my external sd card now. when the phone is booted up it works fine except i tried to do the factory ota update and it keeps failing. i tried reflashing back to stock again and did the update unrooted and it still failed.
i know you guys hate hate when people ask without researching so i did SOME forum browsing and found nothing. sorry i dont really have time to look too extensively. i just want to know how to fix it. i appreciate any help i can get
Joeyjr25 said:
ok so i wouldnt say im a noob but im not as advanced as some of yous. last night i flashed a leaked ics onto my phone and loved it with one exception. i couldnt figure out how to root it. all my apps are backed up on titanium backup and i didnt want to have to get all of them manually. so i flashed back to stock using odin with a file i used back when that crappy update came out. i rooted it with super one click and and then went to put on a prerooted ics... when in recovery mode now i get this message
cant access to '/system/csc/att/system/'
i try putting on cwm and siyah and i keep getting authentication errors and the installation aborts. also recovery mode wont read my external sd card now. when the phone is booted up it works fine except i tried to do the factory ota update and it keeps failing. i tried reflashing back to stock again and did the update unrooted and it still failed.
i know you guys hate hate when people ask without researching so i did SOME forum browsing and found nothing. sorry i dont really have time to look too extensively. i just want to know how to fix it. i appreciate any help i can get
Click to expand...
Click to collapse
Start with getting back to stock using this guide. Check for ICS bootloaders too, you probably flashed them and you have to get stock ones back (careful, flashing bootloaders can cause hardbricking). Once you're back to stock and rooted, you shouldn't need to ever use PC Odin again.
Then use this guide for rooting/flashing.
One other note: when you tried to install CWM, it sounds like you loaded an update.zip onto your phone then tried to install it using stock recovery. Stock recovery won't let you install unsigned update.zips, which is why that method for getting CWM on your phone will never work (hence the authentication error and installation abort). For our phone, CWM is only included in custom kernels, that's the only way to get it on there, and don't even think about updating or changing it via other means. Just flash a custom kernel, it'll include CWM, use it until you want to switch kernels.
Hit my thanks button, I was really nice this time. And post in Q/A next time as well.
EDIT: Skip the second guide if all you want is stock. You should be able to update OTA after following the first guide. Though even if stock is what you want, I highly recommend flashing a custom GB kernel because a) they're more stable and faster and b) you'll have CWM in case you need it.
You started off mentioning about "leak ics" which I have absolutely zero experience.
My suggestion:
1. Try to get it back to stock. Make sure it works correctly.
2. If hasn't rooted yet, do so.
3. Getting CMW into the device by flashing custom kernel.
4. From there, install any ICS ROM you want.
So ,im sorry but its a long story. Hopefully someone can help. My note is Rooted Ive been using TWRP. Everything had been fine until 2 days ago. I tried flashing a ROM i found on Goomanger.( I had been running liquid smooth) just wanted to try something different. Anyways it got stuck on a boot loop. Cant remember the name of the Rom. Anyways i was able to get back to recovery, thankfully. But when i wiped and flashed back to liquid smooth it would say optimizing apps, then it would reach a certain number then reboot and star all over again. So then i tried another Rom and the same thing happened. tried flashing back to stock rooted but it would turn on then completely crash and star booting up again. So finally i was able to flash paraandroid 4.1.2 and Gapps, but here is the kicker i have no service (AT&T) says cannot locate network, my IMEI is gone basically the cellular isn't working. Everything else works fine WiFi,apps, camera. Just cant make calls. I really need your guys help please.:crying:
If you have a suggestion please let me know, i hate using an old Iphone
dar101978 said:
So ,im sorry but its a long story. Hopefully someone can help. My note is Rooted Ive been using TWRP. Everything had been fine until 2 days ago. I tried flashing a ROM i found on Goomanger.( I had been running liquid smooth) just wanted to try something different. Anyways it got stuck on a boot loop. Cant remember the name of the Rom. Anyways i was able to get back to recovery, thankfully. But when i wiped and flashed back to liquid smooth it would say optimizing apps, then it would reach a certain number then reboot and star all over again. So then i tried another Rom and the same thing happened. tried flashing back to stock rooted but it would turn on then completely crash and star booting up again. So finally i was able to flash paraandroid 4.1.2 and Gapps, but here is the kicker i have no service (AT&T) says cannot locate network, my IMEI is gone basically the cellular isn't working. Everything else works fine WiFi,apps, camera. Just cant make calls. I really need your guys help please.:crying:
If you have a suggestion please let me know, i hate using an old Iphone
Click to expand...
Click to collapse
Just odin back to stock. Get a complete factory stock image from the main sticky thread and flash it with Odin and Download Mode. There's a bug on one of the TWRP versions with 4.3-based ROMs that will put it into a bootloop by breaking device reboots. I was unable to flash my way out of the problem and was forced to do a complete reimage which solved all the problems and put me right back to clean-out-of-the-box state, then I reinstalled TWRP (though an older version before the boot loop bug) and re-flashed my custom ROM. The package I used was the stock image and Odin tool all in one .exe, just plug in to download mode and run it and it flashed bootloader, recovery, system, kernel, etc. all back to stock.
CalcProgrammer1 said:
Just odin back to stock. Get a complete factory stock image from the main sticky thread and flash it with Odin and Download Mode. There's a bug on one of the TWRP versions with 4.3-based ROMs that will put it into a bootloop by breaking device reboots. I was unable to flash my way out of the problem and was forced to do a complete reimage which solved all the problems and put me right back to clean-out-of-the-box state, then I reinstalled TWRP (though an older version before the boot loop bug) and re-flashed my custom ROM. The package I used was the stock image and Odin tool all in one .exe, just plug in to download mode and run it and it flashed bootloader, recovery, system, kernel, etc. all back to stock.
Click to expand...
Click to collapse
Thanks thats what i did, I just basically had to use KIES to use the emergency recovery, then root my phone again. My question is what version of TWRP causes this? cause i used the newest version i could find off GOO. My other concerne is, will it accept or be safe to use a custom ROM? Well i gues ill find out :laugh: THANKS AGAIN!
Everyone with the sgh-i717 is having problems with the latest TWRP and the most stable version is 2.5.0.0. Go with that one or you'll be starting all over again I imagine. And don't just stop at the download link in the OP's, read the thread and find out what's going on. The problems with TWRP have been going on for a while and the development threads have a lot of comments about the latest build causing problems. Good luck! :good:
Hello,
I think I made a big error when attempting to install the Hyperdrive rom. I rooted the phone with Odin, then installed Safestrap. Then I rebooted into recovery to install the rom. I did everything perfectly up to this point. But then I decided I was going to wipe the cache. Except I accidentally wiped EVERYTHING. So I cannot boot into the phone because presumably the OS is deleted. The phone just freezes on the "Samsung Galaxy S4" splash screen.
I made a single mistake and now I cannot use my phone.
I think I could probably use Odin to flash the original OS on the phone right? But I would need the file and instructions on how to do it.
I really need my phone on a regular basis so if any of you could tell me what my options are and help me to recover, I would appreciate it.
If I could restore to MI1, that would be the easiest because then I could simply flash the Hyperdrive rom like I was planning.
Thanks. I hope someone can help me.
If it boots up to a splash screen, I'm pretty sure you can hold vol down+power+home to boot into download mode and odin.
Sent from my SCH-I545 using Tapatalk
jrodefeld said:
Hello,
I think I made a big error when attempting to install the Hyperdrive rom. I rooted the phone with Odin, then installed Safestrap. Then I rebooted into recovery to install the rom. I did everything perfectly up to this point. But then I decided I was going to wipe the cache. Except I accidentally wiped EVERYTHING. So I cannot boot into the phone because presumably the OS is deleted. The phone just freezes on the "Samsung Galaxy S4" splash screen.
I made a single mistake and now I cannot use my phone.
I think I could probably use Odin to flash the original OS on the phone right? But I would need the file and instructions on how to do it.
I really need my phone on a regular basis so if any of you could tell me what my options are and help me to recover, I would appreciate it.
If I could restore to MI1, that would be the easiest because then I could simply flash the Hyperdrive rom like I was planning.
Thanks. I hope someone can help me.
Click to expand...
Click to collapse
there are some youtube videos on using ODIN and there are several discussion threads in XDA concerning odin and installing stock images back to the phone
Hey all, just ran into some trouble trying to flash CM-10.2.1 onto my Droid Razr xt912
powered down and booted into recovery, luckily i backed up the stock rom, wiped the stock rom, and tried to flash the .zip file....the program said that the operation was successful, but upon rebooting, no OS loaded up...
the weird thing is that when i was testing out the release to see if i wanted to replace my stock rom, i loaded it onto a partition via safestrap and it seemed to work just fine..
anyone else have the same problems? can anyone think of anything i have done wrong? any help would be greatly appreciated. i realize that this post is slightly vague and i dont know much about flashing roms or anything, only what i have read online. so please by all means ask me anything! i am greatly interested in this ability of the android devices and am wanting to learn as much as possible!!!
thanks again in advance for any help
From what I've read it needs to be loaded onto a partition so if it works you did it right
bendaily2000 said:
Hey all, just ran into some trouble trying to flash CM-10.2.1 onto my Droid Razr xt912
powered down and booted into recovery, luckily i backed up the stock rom, wiped the stock rom, and tried to flash the .zip file....the program said that the operation was successful, but upon rebooting, no OS loaded up...
the weird thing is that when i was testing out the release to see if i wanted to replace my stock rom, i loaded it onto a partition via safestrap and it seemed to work just fine..
anyone else have the same problems? can anyone think of anything i have done wrong? any help would be greatly appreciated. i realize that this post is slightly vague and i dont know much about flashing roms or anything, only what i have read online. so please by all means ask me anything! i am greatly interested in this ability of the android devices and am wanting to learn as much as possible!!!
thanks again in advance for any help
Click to expand...
Click to collapse
Earlier CM 10 builds had a restriction. They can only be flashed on the Slot 1 using Safestrap. This was removed in CM10.3 so if you are trying to flash CM 10.2, you need to use only slot 1.
PS: The update script says that in flash process too.