Destroyed screen - Sprint HTC EVO 4G LTE

I dropped my phone hard. Screen and digitizer still work but the glass is shattered and the corner of the housing is dented pretty badly. What is the best source for parts? I replaced the screen on my evo 3d due to a faulty digitizer and ordered parts for some random place. They turned out to be [email protected] and want to avoid that mistake. All I should need is the digitizer right? Is the glass and digitizer one piece?

It is one piece, the digi/lcd are fused. There are alot of ebay suppliers who will send a new part of it is defective. I've had pretty good luck recently, even on the evo lte a few times.

I always check eBay or amazon
Sent from my EVO using xda premium

I've had to replace a couple screens (not the 4g lte yet) and ebay is a good place to go.
Couple notes:
Some people say you can just replace the glass using a heat gun or blow dryer but I've read more stories of people breaking their lcd doing this I would try to get the glass off first then ordering the parts. If that works you just saved yourself 40 bucks.
If that doesn't work and your feeling clever and fearful this may happen again then I would suggest buying the lcd and digitizer separately. Why? I f#cked it up the first time? You might ask . Simple the factory glue and the tape that the digitizer will come with are two different things and the tape is a lot easier to get off then the glue. Good luck and patience

Asadullah said:
I've had to replace a couple screens (not the 4g lte yet) and ebay is a good place to go.
Couple notes:
Some people say you can just replace the glass using a heat gun or blow dryer but I've read more stories of people breaking their lcd doing this I would try to get the glass off first then ordering the parts. If that works you just saved yourself 40 bucks.
If that doesn't work and your feeling clever and fearful this may happen again then I would suggest buying the lcd and digitizer separately. Why? I f#cked it up the first time? You might ask . Simple the factory glue and the tape that the digitizer will come with are two different things and the tape is a lot easier to get off then the glue. Good luck and patience
Click to expand...
Click to collapse
When I replaced the digitizer on my evo 3d I remember what a pain getting all the sticky pieces apart was so I just went with the whole replacement screen and glass. Got a white one off ebay for not too much. I'm going to have a frankenstein phone
I did take it into sprint just to see if they would maybe offer me some decent deal. The friendly sales guy tried to talk me into a second line and another phone to get me by for a year while I waited for my next upgrade. riight.

Sprint has always replaced my busted screens for free. Only takes about 20min.
From my Evo LTE, yup.

scottspa74 said:
Sprint has always replaced my busted screens for free. Only takes about 20min.
From my Evo LTE, yup.
Click to expand...
Click to collapse
Huh I thought they stop doing that
Sent from my EVO using Tapatalk 2

That's entirely possible, it's been a long time, and they've begun to skimp on ALL services. No more roadside assistance, something screwy with family locater etc.
From my Evo LTE, yup.

Related

[Q] Worst nightmare - dropped my atrix and cracked the screen HELP!

So i've been an Atrix owner for about 2 weeks now and my worst nightmare happend today. I was buying a drink from a vending machine and the phone slipped out of my pocket and fell SCREEN FIRST onto concrete.
I quickly picked it up and noticed THERE WAS A HUGE CRACK in the screen!
I AM SO SAD RIGHT NOW cause i bought the atrix outright from AT&T
i dont think the LCD panel itself was damaged but the glass on the surface only. The display looks perfectly fine still so i was curious if anyone knows how to switch out the glass part? What tools do i need?
I found this one ebay:
http://cgi.ebay.com/Motorola-MB860-...838?pt=LH_DefaultDomain_0&hash=item588d7db4fe
is this the right part?
or do i have to buy the entire LCD, cause its much more expensive:
http://cgi.ebay.com/AT-T-MOTOROLA-A...507?pt=LH_DefaultDomain_0&hash=item33666a4883
also, does anyone know any reputable sellers that sell LEGIT parts such as the digitizer? I'm not sure if i can trust these random ebay sellers...any suggestions would be appreciated
i attached some pictures to show you what happend - i still can't believe it happend
i'm also really surpirsed the gorilla glass broke so easily. The drop was at MOST 1.5 feet..
Bakedbread said:
So i've been an Atrix owner for about 2 weeks now and my worst nightmare happend today. I was buying a drink from a vending machine and the phone slipped out of my pocket and fell SCREEN FIRST onto concrete.
I quickly picked it up and noticed THERE WAS A HUGE CRACK in the screen!
I AM SO SAD RIGHT NOW cause i bought the atrix outright from AT&T
i dont think the LCD panel itself was damaged but the glass on the surface only. The display looks perfectly fine still so i was curious if anyone knows how to switch out the glass part? What tools do i need?
I found this one ebay:
http://cgi.ebay.com/Motorola-MB860-...838?pt=LH_DefaultDomain_0&hash=item588d7db4fe
is this the right part?
or do i have to buy the entire LCD, cause its much more expensive:
http://cgi.ebay.com/AT-T-MOTOROLA-A...507?pt=LH_DefaultDomain_0&hash=item33666a4883
also, does anyone know any reputable sellers that sell LEGIT parts such as the digitizer? I'm not sure if i can trust these random ebay sellers...any suggestions would be appreciated
i attached some pictures to show you what happend - i still can't believe it happend
i'm also really surpirsed the gorilla glass broke so easily. The drop was at MOST 1.5 feet..
Click to expand...
Click to collapse
Yea, thats not a bad deal. You could use DealExtreme though if you wanted. But this seems like a good deal.
Teardown Video.
http://www.youtube.com/watch?v=TbR56jSplRs
Watched a bit and it looks like a good tutorial.
Also, if you don't have the tools you might want this kit.
http://cgi.ebay.com/Motorola-MB860-...195?pt=LH_DefaultDomain_0&hash=item2310051643
It's about the same price and those are both going to ship from Hong Kong. So expect a wait. I didn't find any sellers in the U.S.
There are some that would ship from the U.S. without tools but the price is more like fifty bones instead of 30 something.
Good Luck
JdgM3NT4L said:
Teardown Video.
http://www.youtube.com/watch?v=TbR56jSplRs
Watched a bit and it looks like a good tutorial.
Also, if you don't have the tools you might want this kit.
http://cgi.ebay.com/Motorola-MB860-...195?pt=LH_DefaultDomain_0&hash=item2310051643
It's about the same price and those are both going to ship from Hong Kong. So expect a wait. I didn't find any sellers in the U.S.
There are some that would ship from the U.S. without tools but the price is more like fifty bones instead of 30 something.
Good Luck
Click to expand...
Click to collapse
You are brave soul for recommending such a bad tools.
Sent from my SAMSUNG-SGH-I897 using Tapatalk
Thanks for the recommendations everyone
Do you suggest a better pack of tools? Why do you say they're bad?
Sent from my MB860 using XDA App
greenstuffs said:
You are brave soul for recommending such a bad tools.
Sent from my SAMSUNG-SGH-I897 using Tapatalk
Click to expand...
Click to collapse
Nah, they are more than capable. I replace digitizers frequently and I rarely have to break out my "good set' of tools. Yeah these are simply cheap lumps of plastic. But they work. And these tools should be safer to use than almost anything that the average person, who doesn't do this sort of thing regularly, might have on hand. I just didn't want him to order a digitizer and attack it with a butterknife. I was trying to be subtle about it tho... We don't want anyone to scuff their bezel now do we?
I am always on the lookout for great deals on tools for this. And I look forward to your recommendation for a tool set.
Atrix 4G Glass
You can find a replacement glass here. globalpartsdirect dot com
G2Smooth;129674
33 said:
You can find a replacement glass here. globalpartsdirect dot com
Click to expand...
Click to collapse
You mean http://www.globaldirectparts.com/SearchResults.asp?Search=atrix
Your phone should be under warranty! Call company first!
Sent from my MB860 using XDA Premium App
gonka95 said:
Your phone should be under warranty! Call company first!
Sent from my MB860 using XDA Premium App
Click to expand...
Click to collapse
Warranty covers a broken screen? Reason I ask is because I would rather have MOTO replace the screen (or the phone entirely) than me replacing the screen and voiding the warranty. I do not have insurance
I broke the glass on my phone 3 weeks after I bought it and didnt have insurance on it. I called motorola and they sent me an rma. I sent it in and they sent it back to me fixed in less than a week. If I remember right it cost $90 for them to fix it.
so it was only the digitizer after all?
+1 for photo of toilet roll by the bed, classy...
Sent from my MB860 using Tapatalk 2
JdgM3NT4L said:
Nah, they are more than capable. I replace digitizers frequently and I rarely have to break out my "good set' of tools. Yeah these are simply cheap lumps of plastic. But they work. And these tools should be safer to use than almost anything that the average person, who doesn't do this sort of thing regularly, might have on hand. I just didn't want him to order a digitizer and attack it with a butterknife. I was trying to be subtle about it tho... We don't want anyone to scuff their bezel now do we?
I am always on the lookout for great deals on tools for this. And I look forward to your recommendation for a tool set.
Click to expand...
Click to collapse
A friend and I splurged on the $60 iFixit tool kit because we made some spare cash on the side repairing classmates' phones. It works well, although I still don't know if I would justify the price. It seems that the major complaint on reviews for replacement electronics parts are the parts that come with them, if at all, so maybe getting a better set is worth it if you replace digitizers frequently. Replacing the Atrix digitizer/screen is a fairly easy task compared to other phones until you get to putting the new screen on, at which point trying to get the cables back into the housing becomes a pain.'
Good luck!
consolation said:
+1 for photo of toilet roll by the bed, classy...
Sent from my MB860 using Tapatalk 2
Click to expand...
Click to collapse
Lol.....betting if you look hard enough there's lotion there somewhere too!
Sent from my MB860 using xda premium
Ugh I'm going to have to do this. My digi. Is farked as well. Now, is there a video to put this back together?. I agree that taking it apart is not the hard part at all.
iFixit will have a tear down guide.
Sent from my MB860 using Tapatalk 2
Surprisingly there is no video to put it together...
Let me tell you from experience that it's damn near impossible to put it back together without tearing the digitizer ribbon straight off the screen while trying to slip it through that tiny hole that you pulled it out of. I've replaced two screens and I still don't think I can get it right.
My screen cracked twice while still under warranty, so I played the clueless n00b after I replaced the glass (cracked screens are not covered under warranty) and claimed the phone wasn't working and I couldn't figure out why.
Strange thing is, I also couldn't find a place online that would do replacement digitizers either. I didn't look for long, but if you don't have an option of a warranty return, I'd pay the $50 or so to let someone else do this for you and get it right...
YMMV...
I recommend taking it apart completely, you can attach the digitizer to the bezel/chassis and then you don't have to deal with trying to slide the cable through that tiny hole, you can just clean the digitizer, clean the lcd, put them together and then put the entire mounting plate back together and it just clips straight in...essentially you make this:
http://www.ebay.com/itm/180835204777?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
completely removes the chance of tearing the cable off the back of the digitizer...which is pretty common, sort of adds the step of getting the mounting plate off the fascia bezel...but its not to hard, be careful when popping up the volume/buttons camera cable area, that cable tears easily.

[Q] DIY Digitizer Replacement?

Dropped my phone today and the glass is cracked. Other than the fact that there are superficial cracks, the display and touch screen functionality seem to still be perfect. I have a few questions on how to proceed:
1) From what I can see, the crack is in the DIGITIZER and not the SCREEN although it was my first instinct to call it the "screen." Is this correct?
2) I see a bunch of people on eBay and other sites selling replacement kits that come with the digitizer, tools, and adhesive. There is no way for me to tell if the digitizer is a cheap aftermarket product, or a genuine OEM replacement. Should I care, or will it work just as good as the original either way?
3) I see the DIY thread on how to replace the SCREEN, but could not find one specifically for the digitizer. If I follow the screen DIY, will I get sufficient access to the digitizer, to the point where all I have left to do is unplug and replace, or is there anything else I need to do?
4) If I do this myself, is there a chance that the touch screen functionality will not be as good as it was originally?
I have extensive experience in fixing many different types of electronic and mechanical devices, but have never worked on phones before.
Make us one
If you don't have an Evo3d well you don't have an Evo3d
What I have heard on the evo4g is that the digitizer and lcd are glued together. It is enough of a pain in the ass to seperate them without damaging the lcd itself to be worth buying a lcd/digitizer that is already together and replacing the whole thing.
Now I said evo 4G. I would assume it is the exact same issue for the 3D.
Sent from my EVO 3D on the now or later network
mcmikecruz1 said:
Make us one
If you don't have an Evo3d well you don't have an Evo3d
Click to expand...
Click to collapse
I don't get it...
sand1303 said:
What I have heard on the evo4g is that the digitizer and lcd are glued together. It is enough of a pain in the ass to seperate them without damaging the lcd itself to be worth buying a lcd/digitizer that is already together and replacing the whole thing.
Now I said evo 4G. I would assume it is the exact same issue for the 3D.
Sent from my EVO 3D on the now or later network
Click to expand...
Click to collapse
From what I've gathered, it is glued together and they sell the adhesive. I don't feel like separating them and possibly doing a bad job of putting them back together. I've done that before with taillights (which didn't go too well) and I can't imagine doing it on a phone. Thanks for the input...I could only find 2 complete screen/digitizer combo for sale on eBay. Anyone know of a better source?
nightcrawler7188 said:
From what I've gathered, it is glued together and they sell the adhesive. I don't feel like separating them and possibly doing a bad job of putting them back together. I've done that before with taillights (which didn't go too well) and I can't imagine doing it on a phone. Thanks for the input...I could only find 2 complete screen/digitizer combo for sale on eBay. Anyone know of a better source?
Click to expand...
Click to collapse
Don't even jack with it. My girl had some scratches on her screen and she bought the new plastic piece. Lets just say the 3D is now in the garbage.
jhuff83 said:
Don't even jack with it. My girl had some scratches on her screen and she bought the new plastic piece. Lets just say the 3D is now in the garbage.
Click to expand...
Click to collapse
Yea I'd be really ****ty if that happened to me, especially considering the even the 3d still looks perfect behind the scratches...I guess I'm going to just buy the replacement screen+digitizer combo and do it myself...if I buy them already assembled it should be plug and play from what I have read.

[Q] How many have successfully replaced digitizers?

Hey All..
I saw a TBolt pop up on Craigslist and ended up trading my OG Droid (that I bought from a friend for $50) + $25 bucks for a Tbolt in very good condition but the Digitizer is cracked..
Its not Horrible, I still use the phone and love 4G.. but I want to replace the Digitizer.. I have done a few screens on IProducts and older phones but I have herd lots of horror stories about Digitizers not working after being replaced or dead spots and ghost touches on the TBolt..
So How many have done it and everything has gone 100% fine and where did you get your screen and adhesive? And then how many say i should save my pennies and trust someone else to do it?
I've done 2
1 successful and one a disaster
Put to much 3 m tape on one and it smudged on ends and touch screen
Only worked half way but if you use hair dryer and get really hot and use a small amount of tape it isn't that bad but watched video on YouTube of repair from a repair universe and that's where I bought it
Sent from my ADR6400L using XDA App
carycooke said:
I've done 2
1 successful and one a disaster
Put to much 3 m tape on one and it smudged on ends and touch screen
Only worked half way but if you use hair dryer and get really hot and use a small amount of tape it isn't that bad but watched video on YouTube of repair from a repair universe and that's where I bought it
Sent from my ADR6400L using XDA App
Click to expand...
Click to collapse
So Repair Universe has good stuff? I was hoping someone had sourced a better (read; cheaper) replacement.. $40 is steep compared to the $15 Digitizers that are still working on Itouches i replaced 2 years ago.. and I have never had to separate a LCD and Digitizer before when they were glued together.. that was the biggest thing I am unsure of..
I replaced a digitizer/LCD combo on the Thunderbolt, but I've also replaced the digitizer alone on the HTC Inspire and HD2 many times, and the Thunderbolt is very similar to these two (especially the Inspire). It's not very hard to separate the digitizer from the LCD, just heat the glass up very good first, and make sure you get some good 2mm adhesive for reassembling them. The digitizer does not adhere to the frame at all (though the shell does sort of wrap around and clip onto the glass), it is only adhered to the LCD so you have to be sure to get them nice and tight. The best way to do this is to just get an LCD/digitizer combo pre assembled, then it only takes about 5 minutes from start to finish, and you don't have to be nearly as careful. You can get the combo for like $50 on eBay, just make sure you buy from a reputable seller. Repairs Universe is trustworthy, but they sell the same stuff you get on eBay, and everything is made in China to begin with.
Awesome to hear. I won't be going to repare universe then. 40 for the digitizer alone is steep to me. I am not sure if I want to try and just do the digitizer or just swap both. I bought this TBolt for $60 used so I can probably afford to just buy the whole assembly.
Sent from my ADR6400L using Tapatalk

[Q] Where to get replacement glass?

My phone was dropped earlier however only the glass is cracked, not the actual screen. Everywhere I look, they only sell them as a pair, but I remember awhile back seeing just the glass for a reasonable price.
Where can I get it now?
Thanks!
Here's a glass replacement for $12.80 (Free Shipping)... CLICK HERE
Instructional Video:
Note: This video uses a Fascinate, but the steps taken should be similar to replacing the Vibrant's screen.
Thanks so much!
No problem. Hope you get your phone back up & running.
How come people charge like $100 to replace...?
Sent from my SGH-T959 using xda premium
VeryCoolAlan said:
How come people charge like $100 to replace...?
Sent from my SGH-T959 using xda premium
Click to expand...
Click to collapse
Because that 'replacement glass' is a scam not a digitizer. It will not fit properly and will not function as a digitizer. If you look at the video, the removed digitizer has some wires on it. That allows communication w/ the motherboard. That glass is just glass. Even if you could remove the broken touch panel (digitizer) and fit the glass to the phone you would have no ability to use it.
The digitizers for all amoled Galaxy S phones are not available without the attached display panel. The replacement screen costs $95 just for the part, then add the labor and that is why it is so expensive.
If you notice, even the people who made the video (while showing the removal) don't sell the digitizer alone. Pro shops replace the whole assembly. If you can get the job done for $100 including labor, take it. It's a great price.
ChauncyG said:
Because that 'replacement glass' is a scam not a digitizer. It will not fit properly and will not function as a digitizer. If you look at the video, the removed digitizer has some wires on it. That allows communication w/ the motherboard. That glass is just glass. Even if you could remove the broken touch panel (digitizer) and fit the glass to the phone you would have no ability to use it.
The digitizers for all amoled Galaxy S phones are not available without the attached display panel. The replacement screen costs $95 just for the part, then add the labor and that is why it is so expensive.
If you notice, even the people who made the video (while showing the removal) don't sell the digitizer alone. Pro shops replace the whole assembly. If you can get the job done for $100 including labor, take it. It's a great price.
Click to expand...
Click to collapse
I just need the glass.
I've seen some other videos and I got it down. All you do is take the glass and remove it from the amoled screen then replace. I don't need a digitizer.
Sent from my SGH-T959 using xda premium
So wait, you can't just replace the glass? In the video they remove the glass from the digitizer. Right?
Sent from my SGH-T959 (Samsung Vibrant)
N00B_IN_N33D said:
Wow, I had no idea. I've never taken apart my phone before, but when I came across the glass replacement on Ebay it looked very legit. 99.4% positive feedback, 34 sold, and 7 day money back... But I guess looks can be deceiving. I figured the wire was hidden from view in the picture. I apologize for posting a link to a scam...
Sent from my SGH-T959 (Samsung Vibrant)
Click to expand...
Click to collapse
Not a problem. Unless you have done any repair work on these things you would not know. Most non oled display phones have the ability to replace touch screen and lcd displays individually. Unfortunately, not ours.
This scam works because most people that buy the glass never really get around to installing it, or if they do and it does not work they think they did something wrong. I have repaired a bunch of these things even if you could remove the digitizer sucessfully as shown in the DirectFix video, you can't get a replacement part. Also, this operation needs to be done in a clean room. Any dust on the amoled panel will bruise it when paired with the touch panel so a successful repair is very unlikely outside of the factory. That is why the repair parts are sold together as a unit.
N00B_IN_N33D said:
So wait, you can't just replace the glass? In the video they remove the glass from the digitizer. Right?
Sent from my SGH-T959 (Samsung Vibrant)
Click to expand...
Click to collapse
Yea that's what I saw....
And yes just the glass...since I'm gonna be with this phone for a few more months I need to replace and this is really cheap!
Sent from my SGH-T959 using xda premium
VeryCoolAlan said:
Yea that's what I saw....
And yes just the glass...since I'm gonna be with this phone for a few more months I need to replace and this is really cheap!
Sent from my SGH-T959 using xda premium
Click to expand...
Click to collapse
You can't 'just replace the glass'. The digitizer and front glass are one and the same. They are inseparable.
---------- Post added at 12:55 AM ---------- Previous post was at 12:53 AM ----------
N00B_IN_N33D said:
So wait, you can't just replace the glass? In the video they remove the glass from the digitizer. Right?
Sent from my SGH-T959 (Samsung Vibrant)
Click to expand...
Click to collapse
What you saw was the digitizer/glass being removed from the AMOLED panel. So, as stated before, no, you can't just replace the glass.
FML. -_-
Sent from my SGH-T959 using xda premium
Call me crazy but if people are buying these and not complaining they don't work. Then either they don't want to look stupid by saying they got scammed or they did replace the glass and is possible. I say it's possible but very hard since the thickness is about that of a piece of paper. I saw this on wiki for the superamoled little confusing.
Super Active-Matrix Organic Light-Emitting Diode or Super AMOLED is a display technology (variant from AMOLED) mainly for use in mobile devices such as mobile phones (see the list below for examples). One of the main differences from other display technologies is that the layer that detects touch is integrated into the screen rather than being overlaid on top.
Click to expand...
Click to collapse
Anyone? Is that saying the display (lcd screen) has the digitizer built in the screen itself?
Mandown said:
Call me crazy but if people are buying these and not complaining they don't work. Then either they don't want to look stupid by saying they got scammed or they did replace the glass and is possible. I say it's possible but very hard since the thickness is about that of a piece of paper. I saw this on wiki for the superamoled little confusing.
Anyone? Is that saying the display (lcd screen) has the digitizer built in the screen itself?
Click to expand...
Click to collapse
They are integral but can be separated.... just not rejoined and still work. Notice that the places that show the removal videos DO NOT sell a replacement part, just the entire screen. Most of the glass that is sold as a replacement is purchased from overseas. It costs more to return it than what was spent to purchase it. They are ALL worthless. If there are not wires coming from it it can't be a digitizer. If you remove your broken digitizer and are lucky enough not to destroy you amoled panel you still have nothing to replace it with. Most if not all people who buy these things never get around to attempting the replacement, or if they do, they destroy the panel in the process so they never get the chance see that the glass does not work. They think they screwed it up instead of being ripped off. That's why you don't see negative feedback about those things.... It's the perfect (almost) scam.
If you want to replace your glass buy the entire assembly ($95.00) on eBay and at the end of the process you will have a great phone again instead of a pile of junk.... not to mention feeling like you screwed up your phone.
Well what I'm going to do is wait for my brother to go to Verizon then take his vibrant and use his screen and mess with mine. Though I need to buff out the scratches. If by some miracle I do make it work I will post here. I hate when people find a way to fix something that some of us are trying to figure out and never report back how or just say "I fixed it was simple." WTF WAS IT! had to deal with that with my plasma which I finally did find one thread and fix it.
Sent from my Vibrant using xda premium, running ICS Passion v10.6 OH YEAH!
Digitizer and glass are factory glued together under high temperatures impossible to separate.
Just buy the whole assembly for $90 ( i've seen them for $79 once) with free shipping and tools on ebay. I always send offers using ebay "ask a question" and sometimes they give me few $$ off. Then it is a piece of cake since you can brake off the glass and remove the whole assembly that way.
My personal Vibrant is made of all kinds of used Vibrants and screen assembly comes from Galaxy S 4G which is good replacement too if you also want to get front facing camera.
technically can be done
while i don't recommend anyone else try, I was able to separate the glass from the screen. the glass was cracked but the screen still worked so i bought just the glass thinking it would be an easy replacement. so when i came to find them glued together i used my hot-air gun to melt the glue and remove to broken pieces of glass one by one, very carefully. when putting it back together with the new glass i couldn't re-glue it but the back tray holds the screen in place well enough. there was only one side effect that i have noticed so far. the glass is a little loose since not held to the screen, and i did burn the screen a little bit with the heat gun and it now has minor discoloration. but it is possible with enough patience and a steady hand.
afx420 said:
while i don't recommend anyone else try, I was able to separate the glass from the screen. the glass was cracked but the screen still worked so i bought just the glass thinking it would be an easy replacement. so when i came to find them glued together i used my hot-air gun to melt the glue and remove to broken pieces of glass one by one, very carefully. when putting it back together with the new glass i couldn't re-glue it but the back tray holds the screen in place well enough. there was only one side effect that i have noticed so far. the glass is a little loose since not held to the screen, and i did burn the screen a little bit with the heat gun and it now has minor discoloration. but it is possible with enough patience and a steady hand.
Click to expand...
Click to collapse
Any follow up on this?
Any video/help for broken galaxy s1 i9000 glass?.
I meam the front thing as i understand its just a piece of glass and not a touchscreen. But for the phone you talk about its a touchscren and not just a glass

Screen Replacement

I bought a screen replacement for my crack screen off ebay for a great deal:
http://www.ebay.com/itm/360478218769?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
Yes, it came from china and I hope this screen will work when I replace my crack LCD screen on my phone. How did the screen cracked? Well, I have a desk chair with a roller on the bottom. I kind of roll over it :/ I feel so ashamed hurting my precious phone lol.
Did you get it yet? I've been monitoring this post, since I also have a cracked screen and don't want to spend $200+ dollars on replacing or insurance. Please keep me updated on this. Thanx in advance.
justinmcnairy said:
I bought a screen replacement for my crack screen off ebay for a great deal:
http://www.ebay.com/itm/360478218769?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
Yes, it came from china and I hope this screen will work when I replace my crack LCD screen on my phone. How did the screen cracked? Well, I have a desk chair with a roller on the bottom. I kind of roll over it :/ I feel so ashamed hurting my precious phone lol.
Click to expand...
Click to collapse
don't want to burst your bubble, but that is the digitizer only. i think its really really hard to separate the two from each other. that is why they are so expensive to buy. but hey, might as well try if it is already broke. i understand the lcd is fine btw. i replace screens pretty often and with Samsung, you usually have to buy them fused already. guess it couldn't hurt to try though. good luck to ya, you may need a heat gun and thin wire. keep us updated when it comes in. I'm sure we all would like to know how it goes. good luck
i looked at the listing again, and i don't see any digitizer ribbon. so it looks like no digitizer is even on it. just the lens, but maybe you knew that and this is what you're looking for?
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
I bought 1 but giving up, don't know how to replace so i sold my cracked screen Note and bought another one
Yayodroid said:
don't want to burst your bubble, but that is the digitizer only. i think its really really hard to separate the two from each other. that is why they are so expensive to buy. but hey, might as well try if it is already broke. i understand the lcd is fine btw. i replace screens pretty often and with Samsung, you usually have to buy them fused already. guess it couldn't hurt to try though. good luck to ya, you may need a heat gun and thin wire. keep us updated when it comes in. I'm sure we all would like to know how it goes. good luck
i looked at the listing again, and i don't see any digitizer ribbon. so it looks like no digitizer is even on it. just the lens, but maybe you knew that and this is what you're looking for?
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
Click to expand...
Click to collapse
Yes only for the screen len, not digitizer. I figure I bought it then trying to find the link to replace the screen without digitizer. All of them mention it hard to accomplish. I should had bought the screen with digitizer, but hey I will see how it goes...
Sent from my SGH-I717 using xda premium
just my opinion is to find complete digitizer and lcd fused together, or else you are going to have a bad time. they are very expensive, but it shouldnt be too hard to do as long as you take your time. if you found a digitizer+lens, with out the lcd, it will be really difficult. heat gunning then getting something super thin to slide down to cut between your good lcd and cracked digitizer without scratching the lcd. ive done it on an iphone 4 and the lcd was scratched from it, but it did still work and i didnt break the lcd. if you do lens only, im not sure if you will be able to get the actual digitizer off of the original lens without tearing it an then placing it on the new lens with out bubbling up or anything. i would hate for you to be out a phone for a while. good luck to you sir

Categories

Resources