Related
New to android and would appreciate some help.
My galaxy s2 powers on to 'software upgrade failed...' so I am trying to revert to stock rom.
So far I have:
installed kies and double checked drivers (killed all kies stuff from task manager)
downloaded the stock rom from here: [Heimdall][Odin][Stock][Root]UCKH7 Return/Unbrick to Stock (or Root)
entered download mode on phone (hold volume up+down and plug in usb)
launch odin and put rom in pda slot.
Hit start and it stalls at NAND Write Start!!
tried with heimdall but I keep getting an error after uploading kernel. 'Error: failed to confirm end of file transfer sequence'
been trying tons for the past few hours and am finally getting frustrated. Thanks for any help
Info: att galaxy s2
Already tried: redownloading rom file, tried all my usb ports, tried another computer
Have you killed the Kies tray agent from Task Manager before using Odin?
Also make sure that your phone is in USB debugging mode.
yes, forgot to mention killed all kies stuff.
using heimdall command line I can get the process to start, it gets to 'uploading kernel', goes to 100% and then says 'error: failed to confirm end of file transfer sequence'
kinda feels like progress
what exactly is the rom you're flashing to get back to stock?
The kernel is 100% bone stock, the system image is stock except that it is pre-rooted (su binary and Superuser.apk)
I am including the modem in a separate package since that goes in a separate modem slot, and I don't want to reupload a 200+ MB file if I don't have to.
The kernel + rooted system package is here: http://www.multiupload.com/PNQC9KOD4D
*NEW* - Kernel + non-rooted system package: http://www.multiupload.com/I1G8F47TQ8
The modem package is here: http://www.multiupload.com/VWTSCXE5L0
Click to expand...
Click to collapse
I've tried both rooted and unrooted roms. They contain a pda.tar that I load into odin, or extract for heimdall
from this thread: http://forum.xda-developers.com/showthread.php?t=1286432
can anyone point me to a different rom I could try?
I've tried a ton of flashing methods all on this same rom....
Exactly how are you getting into download mode?
Volume down+power+home
When you connect to Odin computer does it say you are connected and turn green?
Sent from my GT-I9100 using XDA App
i'm getting into download by holding volume up and down and plugging in usb (AT&T GS2).
It says 'odin mode' in red and says 'downloading...'
when I connect to odin it does say i'm connected and turns green.
I just tried to install clockworkmod recovery and it keeps stopping at NAND write start
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> zImage
<ID:0/006> NAND Write Start!!
Click to expand...
Click to collapse
aceofclubs said:
Exactly how are you getting into download mode?
Volume down+power+home
When you connect to Odin computer does it say you are connected and turn green?
Sent from my GT-I9100 using XDA App
Click to expand...
Click to collapse
It turns yellow, not green.
---------- Post added at 03:00 PM ---------- Previous post was at 02:59 PM ----------
Deenybird said:
can anyone point me to a different rom I could try?
I've tried a ton of flashing methods all on this same rom....
Click to expand...
Click to collapse
Safest stock roms that I use are Intratech's
http://forum.xda-developers.com/showthread.php?t=1075278
that's right, it turns yellow, with the green progress bar above
Safest stock roms that I use are Intratech's
http://forum.xda-developers.com/show....php?t=1075278
Click to expand...
Click to collapse
i'd like to try that method. which one do I download for my I777UCKH7 north america AT&T?
No wonder I didn't get that job with the bomb squad
So anyway your sure you're in download mode then?
Sent from my GT-I9100 using XDA App
Deenybird said:
i'd like to try that method. which one do I download for my I777UCKH7 north america AT&T?
Click to expand...
Click to collapse
I might be colour blind but you might make sure you're trying to flash the right firmware for your phone.
Sent from my GT-I9100 using XDA App
it says 'odin mode' in red up top. green robot in center, says 'downloading...'
yes i am sure its the right rom as my box shows version I777UCKH7
heimdall keeps failing after uploading kernel
Yeah don't try and flash the I9100 firmware onto your I777.
The link you gave in your OP I think is where you should be able to get the answers and help you need.
Sorry I know nothing about the I777
Sent from my GT-I9100 using XDA App
Just wanted to post that my problem is solved.
Summary: My AT&T Galaxy SII showed an error on boot (software upgrade failed. connect to kies...). Kies wouldn't even recognize the device so that route was a no go. So as everyone's recommended method of last resort, I decided to flash the device back to stock via odin. I entered download mode (volume up + volume down and plug in usb) and Odin would recognize the device, I would load the stock rom in the PDA slot and hit start and it would begin normally, but it would always fail after a few seconds on 'NAND write start', or 'factoryfs.img'. So I got a 1 click download solution using odin for reverting my phone back to stock. Same thing, it would recognize the phone, but stall out and fail. I also tried flashing clockworkmod via odin but and same problem. People recommended I try heimdall. It would recognize my device, and then fail after 'kernel 100%'.
I tried both programs on 3 different computers, and must have tried 12 different USB slots amongst all of them. I'm fairly handy with this stuff and I worked for hours on it.
xtra info: I had successfully used odin on my computer to flash a kernel just a week ago so I know my stock usb cable was working etc...
Resolution: So I hung my head and drove to the ATT store. After pressing a few buttons on the device and not getting anywhere they sent me to a nearby Device Support Center. I told the girl at the counter that my phone booted to this error screen and that connecting it to Kies did nothing. She asked if it was ok that in the case that she couldn't fix it she would offer me a replacement. I said that was fine and after 10 minutes in the back room she came out with a replacement (free of charge).
Well that was the good news. For the bad news, unfortunately I still don't know how to fix the problem I had, and don't really know how to avoid it in the future. I thought phone's could only get truly bricked if you messed with PIT files and such. There didn't seem to be anything more I could do than flash with odin or heimdall as those were already last resorts. I know I had the right files, the right drivers, and working usb. No matter how crazy I got with my iphone, a full restore was only a click away by plugging in to iTunes. Somehow I messed up my phone so bad that even the device support center couldn't fix it....? Shouldn't have had to be like that.
Thank yous: Thanks to ATT for having a walk-in store and for so easily offering up a replacement. Thanks to the many people on the web who offered remedies.
tl;dr - phone broke, att replaced, still a mystery
recently tried updating to ics via kies but it failed and phone said to eneter recovery... tried that nothing happened it won't enter recovery mode but will access download mode.
searched for a few days for answers and tried flashing with Odin ... the firmware fails then tried the kernel and this passed but still won't flash.
Used a guide on here and followed all methods and then resorted to flashing the bootloader but this also failed now I'm stuck with 2 counts on the kernel a void warranty and a USB jig that won't reset the counter!
Any help please...I just need the phone up and running ! I've rooted and flashed other phones but tried keeping this standard but kies altered that!
don't say use search button as I've been searching for days now this is last resort before paying out at service centre.
Thanks
Andrew
What Magic are you expecting from here now my friend, we to type here the same what you found while searching...
Since you are able to download mod, did you try changing the PC for ODIN flash
first is it i9100 and not other varient?
second just learn how to flash using odin nothing more.
http://forum.xda-developers.com/showthread.php?t=1075278
comeback after this
ZACQ8 said:
What Magic are you expecting from here now my friend, we to type here the same what you found while searching...
Since you are able to download mod, did you try changing the PC for ODIN flash
Click to expand...
Click to collapse
yes zacq8 very true buddy
Don't quite understand exactly what you are asking me but I turned Kies off and all running software and run Odin 1.85 the kernel will flash but the phone won't accept any firmwares at all! it fails .
is there any way to get the phone into recovery ? I thought there may be some way using ADB or another way around to enter recovery or restart update !
dont use stock ics firmware, use the gingerbread version
step 1. download your stock firmware from here
step 2. flash using odin
How to flash.
- Open ODIN.
- Select CODE / MODEM / CSC.
- Put phone in download mode. (HOME - VOLUMN DOWN - LOCK)
- Connect phone with cable. Push start (Wait till phone reboot on Android start screen!)
step 3. download old bootloader from here,
then flash it useing odin (phone must be in download mode)
put it in PDA: and then click start
step 4. learn how to make your own jig from here
step 5. once made just shutdown phone and plug it in, wait 8 seconds
that easy
>>>read this other user's<<<
if i made a mistake dont be mean about it, just confront me, then i will fix my
mistakes
@ starbogt go in the download mode man wen ur kies says for recovery mode thts it
@ ANDROID1997 thank you I've tried that method and it fails the firmware every time.
@ atifis this is the i9100
@ rocky23 thanks but this is what I tried but the phone won't emergency recover with Kies I've tried on 3 pcs and it won't work.
The phone only came back from Phones 4 U a month ago due to a failed USB ! and now this ! been most unreliable phone I've had!
Is there anything else I can try?
when installing boot loader I get
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> Sbl.bin
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
did you try a diffrent usb cable
clean usb port on phone and pc
disable samsung kies
****do you assume that the phone "see's the light"
yes but there no such thing as a dead phone ****
---------- Post added at 02:19 PM ---------- Previous post was at 02:14 PM ----------
take out battery
check under the battery does it say
MODEL: GT-I9100T
or
MODEL: GT-I9100
More trys:
A) If you are on windows 7 run ODIN as administrator ,
b) Try with different versions of ODIN
m8 theres something ur not following correctly can u pm me ur correct prblm in clear language...
Its gt-i9100 tried different cable but going to try pc without kies later if no joy i will have to go to repair centre I need the phone sorting quick
@ZACQ8 I'm on windows 7 as hidden admin as well no luck and tried Odin 1.83 and 1.85
Rocky23 how do you mean in a clear landuage ? I will try and get a message together when my sons in bed thank you
Quick update .... Changed PC and uninstalled kies changed to the ics and bootloader installed and everything installed just dowlnoading all my apps now.
Thank you to all that have posted and helped never needed to post before so thanks everyone.
starbogt said:
Quick update .... Changed PC and uninstalled kies changed to the ics and bootloader installed and everything installed just dowlnoading all my apps now.
Thank you to all that have posted and helped never needed to post before so thanks everyone.
Click to expand...
Click to collapse
hi starbogt,
could you please write down the step by step the way you've suceeded bringing the phone up? as my s2 couldn't get into download mode nor recover mode, it just show a picture of phone---/!\---pc, anyway the odin still can detect my phone. i see some others are experience this problem too but haven't get clear solving yet. many thanks if there is any master here can help
droid_me said:
hi starbogt,
could you please write down the step by step the way you've suceeded bringing the phone up? as my s2 couldn't get into download mode nor recover mode, it just show a picture of phone---/!\---pc, anyway the odin still can detect my phone. i see some others are experience this problem too but haven't get clear solving yet. many thanks if there is any master here can help
Click to expand...
Click to collapse
@ Droid_one : the ways to get Download mod from this stage are
1) pull the batter out and insert and Voi-down + Home + Power
2) USB jig
did you try any of the above
EDIT : your case and starbogt's case are different, he was able to get Download mod and unable to falsh from ODIN...
ZACQ8 said:
@ Droid_one : the ways to get Download mod from this stage are
1) pull the batter out and insert and Voi-down + Home + Power
2) USB jig
did you try any of the above
EDIT : your case and starbogt's case are different, he was able to get Download mod and unable to falsh from ODIN...
Click to expand...
Click to collapse
hi zacq8,
thank you for your quick reply, very appreciated.
i just realise my s2 is i9100G, while i flashed with i9100, i think this caused the problem.
i've tried the 1st step you mentioned, but it still displaying the phone---/!\----pc picture. yet i dun know where to get usb jig in my region, do you have any other remedies with this?
sorry, i'm new with the work and the forum, should i create a separate thread or just keep in?
you should get DL mod and to flash a ROM from ODIN, this is the only remidy now as far my knowledge...
I heard the "Phone!PC" also a kind of forced download mod, but (after making 100% sure) keep it for worst and last case if you fail to get DL mod for flashing a stock ROM. (please dont attempt now I am not fully sure)
Where is your location, check somebody near to you is available in these Jig owners, http://forum.xda-developers.com/showthread.php?t=1495867
also it is not a big deal to make a jig, if you now how to solder, can follow this video guide : http://galaxys2root.com/galaxy-s2-hacks/how-to-make-a-usb-jig-for-your-galaxy-s2/
No need to create a seperated thread, you continue posting here only.....bothway you will get same response.
ZACQ8 said:
you should get DL mod and to flash a ROM from ODIN, this is the only remidy now as far my knowledge...
I heard the "Phone!PC" also a kind of forced download mod, but (after making 100% sure) keep it for worst and last case if you fail to get DL mod for flashing a stock ROM. (please dont attempt now I am not fully sure)
Where is your location, check somebody near to you is available in these Jig owners, http://forum.xda-developers.com/showthread.php?t=1495867
also it is not a big deal to make a jig, if you now how to solder, can follow this video guide : http://galaxys2root.com/galaxy-s2-hacks/how-to-make-a-usb-jig-for-your-galaxy-s2/
No need to create a seperated thread, you continue posting here only.....bothway you will get same response.
Click to expand...
Click to collapse
wonder if i can charge the battery in this situation? i'm not sure how much it is left from the last time it run.
okay, i'll try to get a jig asap, meanwhile could you please guide step by step how to use the jig and odin for s2 i9100G? does it restore to the original factory ROM or others?
Bricked Phone?
This is a solution I found to work on my own GS4. The Verizon Update Utility seems to be able to restore a phone without any problems. However, if you are in a Soft-brick situation all of your data will most likely be erased (which is why we are told to backup so much). I looked all over the place for the Upgrade Assistant online since you can't access it from your phone if it's bricked, so I figured I could post it here and hopefully help someone out who has a bricked phone.
Instructions:
Install the Upgrade Assistant and SAMSUNG USB Drivers
Put your phone in Download mode
Connect to your computer (allow driver detect on Windows)
Open the Upgrade Assistant
Go to Repair Assistant
Press Start
Wait: the Process should take anywhere from 30-90 minutes (because it downloads the Stock 1.6ish gb rom)
In the Zip file you will find:
The Verizon Upgrade Assistant (PC/MAC)
Samsung USB Drivers
These files come directly from the stock ROM on the GS4
Hope it helps!
EDIT: The Mac Software installs great, however the Windows software doesn't seem to be working for me. So if you can get it to work thats awesome!
Please note: this is not my software and is only the software of it's respective owner. I do not claim for it to be mine, I am only posting a link so as it can be used to help.
Keep in mind that if youre on MDK this will probably up you to ME7... and lock your Booyloader.
If on MDK and you brick your device, I would ask around for assistance to manually unbrick
Sent from my SCH-I545 using xda app-developers app
PetrichorXFi said:
Keep in mind that if youre on MDK this will probably up you to ME7... and lock your Booyloader.
If on MDK and you brick your device, I would ask around for assistance to manually unbrick
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
Hi Guys
I've googled the internet soooo hard trying to find this file attached at the first post of this thread but sadly the attachment is gone
I've spent hours trying to find a download link but sadly i couldn't find any at all!!
so please please please, can someone re-upload it for me and everyone out there looking for it.
Thank you guys !
flashbolt said:
Hi Guys
I've googled the internet soooo hard trying to find this file attached at the first post of this thread but sadly the attachment is gone
I've spent hours trying to find a download link but sadly i couldn't find any at all!!
so please please please, can someone re-upload it for me and everyone out there looking for it.
Thank you guys !
Click to expand...
Click to collapse
You need to take more Google jujitsu classes lol. If you search the name of the zip on Google it's the first link that comes up
Yaaaay xD!!
joshm.1219 said:
You need to take more Google jujitsu classes lol. If you search the name of the zip on Google it's the first link that comes up
Click to expand...
Click to collapse
i already did that xD
googling again with ur keyword, please wait....
yes i see what u meant, but all the link are not available/downloadable
that's why i had to ask u, i think this is my first time to ever ask something in any forum hehe, i've never been this stuck in my life xD
but sadly I've lost all my chakara xD
anyway it seems that even if i did find it i won't be able to install it, the reason why is like below
1- i remembered i had a note 3 verizon, i attached it, copied the vzw software assistance.exe and all files related
2- tried to install it from my local harddrive copy, nothing would lunch or pop-up
3- backed it up as *iso and mounted it, still got nothing lunching or popping up when i try to open the *exe
4- connected my note 3 and lunched it from the phone and it directly pop up an agreement message with "install" button,
one must be connected to the internet when installing
so after all it turns out without a verizon device connected and used to install it, one cant use the software unless it's already installed
so i thought i'd share this info for anyone who wants
anyway thank you for your time and help =D
unbricking my note 2 sch-i605 ongoing.. xD
wish me luck =d
i'll post this just for information
so after i have soft bricked my phone to a brick that cannot be fixed through odin i managed to fix it with the verizon software repair
the error i have faced was that everytime i try to flash any rom or anything to sch-i605 verizon note 2 phone it will return an erorr messag sayong
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> sboot.bin
<ID:0/008> NAND Write Start!!
<ID:0/008> FAIL!
<ID:0/008>
<ID:0/008> Complete (Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
so after installing Verizon software assistant and connecting my phone to it, it have completely repaired my phone :victory:
tip: u have to install "Verizon software assistant" from a working Verizon phone only, you can't install it from copied files.
Thanks for all you provide XDA Dev's !!!
The software might be too outdated, I can't get it to run. It keeps force closing on my mac. It won't even launch in windows, I found a report of a user that had removed the samsung signature on the file with launching success, but even that didn't work for me. Lol I'm just going to have to wait for the stock rom to download so I can Odin it
Same situation here - I am stuck with the phone telling me to run Verizon Software Repair Assistant. and that does not work on Windows 10. I was able to remove the digirtal signature. I have the task manager running and the app does appear to launch but gets closes right away. Stuck phone - please help....
Just an update for those who care. I had success with windows 10. I plugged in a working verizon phone to get the upgrade assistant which has the repair assistant in it. It installed without a hitch. It wouldn't recognise my phone until I manually put it in download mode. Took about 7 mins to repair with fiber internet.
Sorry folk, can't install software.
Any help?
Running Windows 7 x64, drivers installed.
Regards
Recovere said:
Bricked Phone?
Instructions:
Install the Upgrade Assistant and SAMSUNG USB Drivers
Put your phone in Download mode
Connect to your computer (allow driver detect on Windows)
Open the Upgrade Assistant
Go to Repair Assistant
Press Start
Wait: the Process should take anywhere from 30-90 minutes (because it downloads the Stock 1.6ish gb rom)
EDIT: The Mac Software installs great, however the Windows software doesn't seem to be working for me. So if you can get it to work thats awesome!
Please note: this is not my software and is only the software of it's respective owner. I do not claim for it to be mine, I am only posting a link so as it can be used to help.
Click to expand...
Click to collapse
Working file FOUND!!!
Thanks for the info and initial file OP. Unfortunately, the zip is out of date and does not install on any version of Windows I have tried.
I have tried Windows 7 64 bit and 32 bit, as well as windows XP 32 bit. The assistant did not open in any of these versions of windows.
I found a working file...
Direct download link (as of 11/3/2016) for the repair assistant from Samsung's website:
http
://support
-us.samsung.com/VerizonSoftwareUpdateWin/
I was directed to the above download link from this Verizon web page. You can find any needed instructions on using the tool there.
https
://www
.verizonwireless.com/support/knowledge-base-80201/
Here is the Verizon page for the Software Upgrade Assistant:
https
://www
.verizonwireless.com/support/knowledge-base-80200/#windows
Hello all!
Yesterday I started to 1st time flash my 9100g to presumably "original" firmware (I9100GXXLSR_I9100GXXLSP_I9100GDBTLS1_HOME.tar) with the before mentioned firmware and a PIT I've found somewhere in a forum together with 1.85 Odin (u1_02_20110310_emmc_EXT4) for that phone. Unfortunately it seems that I "killed" (Hard or Soft bricked - don't know) my phone (So far I remember I switched Nand erase by lack of attention also, but stopped before complete).
Now the phone starts only in "Phone-exclamation-PC" mode ever and ever again - even with a JIG. Odin 3 and 1.85 recognizes the phone, but don't get further than "Setup Connection". Sometimes I get a connection after I used Jig (still at that showing that exlamation screen), and can flash something, but not always. Kies doesn't get a connection.
So my questions:
1. Is it completely bricked?? (meaning: Sending to Samsung)
3. If not, how can I recover it? (I Don't know, but looks like a kernel startup problem, evtl. wrong PIT)
2. If yes, can someone tell me how much one have to pay for repair in average?
(Before that I made a complete flash/nand mem backup by su and dd of this phone on a 16GB USB Stick - can I use that somehow?)
peteralliston said:
Hello all!
Yesterday I started to 1st time flash my 9100g to presumably "original" firmware (I9100GXXLSR_I9100GXXLSP_I9100GDBTLS1_HOME.tar) with the before mentioned firmware and a PIT I've found somewhere in a forum together with 1.85 Odin (u1_02_20110310_emmc_EXT4) for that phone. Unfortunately it seems that I "killed" (Hard or Soft bricked - don't know) my phone (So far I remember I switched Nand erase by lack of attention also, but stopped before complete).
Now the phone starts only in "Phone-exclamation-PC" mode ever and ever again - even with a JIG. Odin 3 and 1.85 recognizes the phone, but don't get further than "Setup Connection". Sometimes I get a connection after I used Jig (still at that showing that exlamation screen), and can flash something, but not always. Kies doesn't get a connection.
So my questions:
1. Is it completely bricked?? (meaning: Sending to Samsung)
3. If not, how can I recover it? (I Don't know, but looks like a kernel startup problem, evtl. wrong PIT)
2. If yes, can someone tell me how much one have to pay for repair in average?
(Before that I made a complete flash/nand mem backup by su and dd of this phone on a 16GB USB Stick - can I use that somehow?)
Click to expand...
Click to collapse
1. It definitely looks like a Service Centre job, but I may be wrong. The "phone-exclamation-PC" is a type of download mode. So that means you only have soft brick, and not a hard one.
2. Yup, wrong PIT it is. You should be careful before flashing PIT files mate. You can try flashing stock firmwares via Odin to see if anything succeeds. But I doubt it will.
3. It is usually the cost of a new motherboard + service charges.
For better answers and guidance, you should state your issue here:
http://forum.xda-developers.com/showthread.php?t=1585413
1. It definitely looks like a Service Centre job, but I may be wrong. The "phone-exclamation-PC" is a type of download mode. So that means you only have soft brick, and not a hard one.
2. Yup, wrong PIT it is. You should be careful before flashing PIT files mate. You can try flashing stock firmwares via Odin to see if anything succeeds. But I doubt it will.
Click to expand...
Click to collapse
Thanks! Yes.
So, a WARNING from me: The PIT "u1_02_20110310_emmc_EXT4.pit" for the phone version "I9100GXXLSR_I9100GXXLSP_I9100GDBTLS1_HOME.tar" which is posted in some forums, IS WRONG!
CORRECT ONE IS: "omap4_all_20110627_emmc.pit" (Here attached; MD5: 8fd1dd2630dd844abe9183203fa438f7)
For better answers and guidance, you should state your issue here:
http://forum.xda-developers.com/showthread.php?t=1585413
Click to expand...
Click to collapse
'll do
S6 edge stuck on opening logo of "Samsung galaxy S6 edge" - it's not mine, so I can't know the history that caused it - but I think it's related to a bad try of rooting.
when trying to flash a new stock firmware from Sammobile getting the same problem - even after wipe and wipe cache.
on recovery getting this messege on the bottom:
dm-verity vertification failed... need to check DRK first...
this is what I tried to do to fix it:
1) flashed newest stock - still no do.
2) tried to flash with smart switch - it did flash - but it didn't help - phone still in bootloop.
3) flashed S6-UniKernel_v6-0001-ODIN or S6-UniBase_BOG8_v2 - it did helped, the phone worked, but I lost the IMEI and needed a certificate to fix the IMEI, I did it and the phone works fine..... BUT I can't left it with a custom rom 'cause I want the original updates and the original stock rom.
4) tried to flash the repair firmware G925FXXU1AOCV (comes with 4 files CSC, AP, MODEM and BOOTLOADER) which is 5.0.1, so it fails (tried also with pit file) - didn't do.
5) last thing I'm willing to try - is to split a new firmware to CSC MODEM BOOTLOADER and AP by myself... the only problem is - I don't actually know how to do it.
another thing I've noticed on the download mode it is written:
Current Binary: samsung Official and System status: custom
I was wonder if someone can give me a clue what to do, and how to fix this problem.
thanks!
What country are you from? Are you sure the phone isn't on 5.1.1??
Download the firmware from sammobile of your own country or the nearest country/countries, put the device in Odin mode and try to flash that one through Odin "AP" Okay "IF IT FAILS" (copy the Odin log and paste it on this thread. If it succeeds LET US KNOW PLEASE.
Be sure of the Android version.. If that's impossible my safe bet is to flash it with a rom for 5.1.1
You shouldn't mess with the PIT files!
curiouswrecker said:
What country are you from? Are you sure the phone isn't on 5.1.1??
Download the firmware from sammobile of your own country or the nearest country/countries, put the device in Odin mode and try to flash that one through Odin "AP" Okay "IF IT FAILS" (copy the Odin log and paste it on this thread. If it succeeds LET US KNOW PLEASE.
Be sure of the Android version.. If that's impossible my safe bet is to flash it with a rom for 5.1.1
You shouldn't mess with the PIT files!
Click to expand...
Click to collapse
hey,
first of all, thanks for the replay!
If I flashed with smartswitch - then it should flash the newest rom and the one who fits for the device.
what I flashed in odin is: G925FXXU3COJ1_G925FOJK3COJ3_G925FXXU3COJ6_HOME.tar
which is Israeli firmware and 5.1.1
Entebox said:
hey,
first of all, thanks for the replay!
If I flashed with smartswitch - then it should flash the newest rom and the one who fits for the device.
what I flashed in odin is: G925FXXU3COJ1_G925FOJK3COJ3_G925FXXU3COJ6_HOME.tar
which is Israeli firmware and 5.1.1
Click to expand...
Click to collapse
Okay, BUT when you ran Odin did it succeed or fail flashing the device?
If it failed what was displayed on Odin logs?
If it failed, Please re-flash your device again through Odin and whether it fails OR succeeds, COPY THE LOG AND PASTE IT HERE !
I need to see the logs, if you want help.
curiouswrecker said:
Okay, BUT when you ran Odin did it succeed or fail flashing the device?
If it failed what was displayed on Odin logs?
If it failed, Please re-flash your device again through Odin and whether it fails OR succeeds, COPY THE LOG AND PASTE IT HERE !
I need to see the logs, if you want help.
Click to expand...
Click to collapse
It didn't fail when flashing in odin.. just stuck on samsung logo.
Read the first post. I wrote everything I did..
Entebox said:
S6 edge stuck on opening logo of "Samsung galaxy S6 edge" - it's not mine, so I can't know the history that caused it - but I think it's related to a bad try of rooting.
when trying to flash a new stock firmware from Sammobile getting the same problem - even after wipe and wipe cache.
on recovery getting this messege on the bottom:
dm-verity vertification failed... need to check DRK first...
this is what I tried to do to fix it:
1) flashed newest stock - still no do.
2) tried to flash with smart switch - it did flash - but it didn't help - phone still in bootloop.
3) flashed S6-UniKernel_v6-0001-ODIN or S6-UniBase_BOG8_v2 - it did helped, the phone worked, but I lost the IMEI and needed a certificate to fix the IMEI, I did it and the phone works fine..... BUT I can't left it with a custom rom 'cause I want the original updates and the original stock rom.
4) tried to flash the repair firmware G925FXXU1AOCV (comes with 4 files CSC, AP, MODEM and BOOTLOADER) which is 5.0.1, so it fails (tried also with pit file) - didn't do.
5) last thing I'm willing to try - is to split a new firmware to CSC MODEM BOOTLOADER and AP by myself... the only problem is - I don't actually know how to do it.
another thing I've noticed on the download mode it is written:
Current Binary: samsung Official and System status: custom
I was wonder if someone can give me a clue what to do, and how to fix this problem.
thanks!
Click to expand...
Click to collapse
You mean this post? It isn't clear enough, if you want help answer the questions people ask otherwise no one can help you.
And look, we are not talking about the device but we are talking about ODIN! Does ODIN fail or succeed flashing?
IF ODIN SUCCEEDS WITH FLASHING, THEN TELL ME!
SUCCEEDS Like This;
https://kpmgsecurity.files.wordpress.com/2014/12/odin-pass-autoroot.png
Or
FAILS Like This; http://ajqi.com/wp-content/uploads/...or-and-nand-erase-all-for-Samsung-devices.jpg
OKAY?
Entebox said:
S6 edge stuck on opening logo of "Samsung galaxy S6 edge" - it's not mine, so I can't know the history that caused it - but I think it's related to a bad try of rooting.
when trying to flash a new stock firmware from Sammobile getting the same problem - even after wipe and wipe cache.
on recovery getting this messege on the bottom:
dm-verity vertification failed... need to check DRK first...
this is what I tried to do to fix it:
1) flashed newest stock - still no do.
2) tried to flash with smart switch - it did flash - but it didn't help - phone still in bootloop.
3) flashed S6-UniKernel_v6-0001-ODIN or S6-UniBase_BOG8_v2 - it did helped, the phone worked, but I lost the IMEI and needed a certificate to fix the IMEI, I did it and the phone works fine..... BUT I can't left it with a custom rom 'cause I want the original updates and the original stock rom.
4) tried to flash the repair firmware G925FXXU1AOCV (comes with 4 files CSC, AP, MODEM and BOOTLOADER) which is 5.0.1, so it fails (tried also with pit file) - didn't do.
5) last thing I'm willing to try - is to split a new firmware to CSC MODEM BOOTLOADER and AP by myself... the only problem is - I don't actually know how to do it.
another thing I've noticed on the download mode it is written:
Current Binary: samsung Official and System status: custom
I was wonder if someone can give me a clue what to do, and how to fix this problem.
thanks!
Click to expand...
Click to collapse
Im going through the same madness for over 2 weeks...
heres my thread with a lot of amazing people tring to help....
maybe something there will help and apply to u and get urs up an running
http://forum.xda-developers.com/galaxy-s6-edge/help/bricked-s6-edge-sm-g925f-help-please-t3286385
please let me know if you get any sort of fix as i think im having same sort of bootloader issue....
Hey Ice, i didn't get your reply on ur thread sorry.
Do you have the same UniKernel as described above?
Please give me all info you have about your device and the current condition of the device (please be clear about what you can do with the device now and how you get to a certain menu such as Recovery/OdiDLmode/Smartswitch/Bootloop*kind of bootloop.)
Hope to be of good help.
curiouswrecker said:
Hey Ice, i didn't get your reply on ur thread sorry.
Do you have the same UniKernel as described above?
Please give me all info you have about your device and the current condition of the device (please be clear about what you can do with the device now and how you get to a certain menu such as Recovery/OdiDLmode/Smartswitch/Bootloop*kind of bootloop.)
Hope to be of good help.
Click to expand...
Click to collapse
Hi thanks,
have no idea about unikernel and have not tried anything with unikernel,
read someting about this somewhere else too,, something about the kernel not even loading cud be a problem?
phone is a galaxy s6 edge SM-G925F
was working fine and apparently on hungarian XEH firmware but not sure if it was on 5.02 or 5.1.1 when 16 year old kid did something or the other with it to put into bricked state.
have no idea of its previous info or condition as it was handed to me in a bricked state
only thing i can do with device is get into download mode and flash via odin...
have never ever been able to get it into recovery mode ever !!!! not even after any successful flashing
I can flash many stock files either the single tar files or either the 4 part multifirmware files
Can do flash and emergency recovery firmware through samsung smartswitch
but no matter what flash if its odin stock firmware flash or samsung smartswitch flash have never seen recovery and always can never get past the white samsung galaxy edge 6 with powered by android in white at bottom too
after succesful flashes in odin cant get out of download mode if auto reboot is ticked, only way out is to hold vol down and power. or get back into download mode then vol down to cancel/restart,
phone just never gets past that white message screen, sometimes that message will splash across screen continuouly like its turning on and off...like some sort of bootloop.... depending how i try to power/boot the phone back up again
and then sometimes it will just stay on the screen forever lit up and frozen/hanging...
strange thing that is happening now if you look at the last few attempts of flashing the 4 part multi firmware file and ticking re-partition to fix the pit files...
once i turn phone off out of download mode.... i cant power the phone/boot it up using just the power on button.
normally i assume to start the phone or turn phone on all u would need to do is hold power button.
so if phone is powered down or turned off after flash, power button alone will not turn it back on, have to go back into download mode and restart from there
i hope any of all that makes any sense at all
Here is a question for you.
When the device is OFF and you plug it into your computer, does the device then jump to the Smart Switch screen?
Btw IMPORTANT when you say that you "flash" the device through odin are you referring to the pictures on your thread where the logg states that it failed on "nand write" and once on "hidden.img" or did it actually pass after the complete flashing of all the files "hidden.img" included?
Firstly need to try this; when the device is stuck in the bootloop you have to do this.
It shows you this type of screen (1st)
http://www.pocketpc.ch/attachments/...49759183-s6-edge-bootloop-20151210_155028.jpg
(does it say kernel isn't seandroid enforced?)
Then this 2nd screen shows up
http://zidroid.com/wp-content/uploads/2014/03/Galaxy-S5-Boot-Animation.png
RIGHT after the 2nd screen SAMSUNG LOGO disappears press volume UP, HOME and POWER you need to be VERY FAST.
Then once the (1st) screen pops up again, release the POWER then volume UP and HOME buttons.
Maybe it's possible that it'll jump into recovery, even if it does this is not the solution just a way to diagnose.
Don't worry we'll fix it!
---------- Post added at 02:00 AM ---------- Previous post was at 01:10 AM ----------
If you have to flash it in any way to get it in a bootloop then the test isn't required! Don't do it.
Try the XDAdevelopers application!
icecoolpsyco said:
Hi thanks,
have no idea about unikernel and have not tried anything with unikernel,
read someting about this somewhere else too,, something about the kernel not even loading cud be a problem?
phone is a *GALAXY S6 EDGE SM-G925F*
was working fine and apparently on hungarian XEH firmware but not sure if it was on 5.02 or *5.1.1*
i hope any of all that makes any sense at all
Click to expand...
Click to collapse
This is what i gathered for you guys as a possible fix, it would work 100% if you guys didn't mess with EVERYTHING IN ODIN!
Because i have tested it myself several times.
READ EVERYTHING CLEARLY
4# When you mess with an s6 to the point that it does not turn on anymore and it only reacts until you plug it into a computer then it shows a screen "error occurred during update use Smart Switch..."
Well by that point Smart Switch mode partially takes over and you can only flash the device successfully in Smart Switch mode using Odin on the computer NOT Smart Switch.
(this knowledge will be useful later)
!!! PART 1 !!!
Here we go, follow this in detail.
STEP 1. You need to download the original Odin 3.10.6 from XDA here below:
http://forum.xda-developers.com/attachment.php?attachmentid=3109599&d=1420980613
STEP 2. Download the Kernel below:
http://mirror31.downloadandroidrom....nibase/S6-UniBase_BOG8_v2.tar?token=514002462
STEP 3. Open Odin on your computer as administrator.
STEP 4. Now connect your device to your computer.
STEP 5. Put your device/phone in Odin mode.
(volume down, home and power)
STEP 6. Make sure Odin has detected the device.
STEP 7. Load the Kernel in "AP" and wait 1 minute, then click START.
It should say PASS! However if it does not succeed, reboot the device and try it again in Smart Switch mode.
(It should actually pass the first try if these simple instructions are followed properly)
_____________________________________________
!!!PART 2!!!
STEP 1. Download this Firmware below:
http://www.sammobile.com/firmwares/download/62003/G925FXXU3QOKN_G925FVFG3QOKN_VDF/
STEP 2. Open Odin as administrator.
STEP 3. Connect your device to your computer.
STEP 4. Put your device/phone into Odin mode.
(volume down, home, power)
STEP 5. Make sure Odin has detected your device.
STEP 6. Load the Firmware in Odin "AP" and WAIT a few minutes UNTIL Odin is done reading the file. THEN CLICK on START and install the Firmware!
!!! IMPORTANT !!!
1st Possibility, if Odin shows "FAIL" "hidden.img" then that's a GOOD THING!
your phone is allmost fixed.
(Let me know if that happens.)
2nd Possibility, if Odin stops at "Nand Write" you must start over, unplug your device make sure it's OFF, then plug it back into the computer in order to boot the DEVICE into SMART SWITCH MODE and then follow the "STEPS 2,3,5,6" again!
DO NOT FOLLOW "STEP 4" Leave the device in SMART SWITCH MODE. (read above "4#")
HOWEVER
If Odin shows "PASS" then DO NOT UNPLUG the DEVICE! Go get yourself a coffee your device should be perfectly fixed!
Just unplug it AFTER A FEW MINUTES and try to switch it on, if it doesn't boot up? All you need to do is replug it into the computer and see if it boots up by itself (this does occur sometimes).
!!! LET US KNOW !!!
You can proceed rooting your device ask for help for a complete root guide for this specific device/model SM-G925F.
EDITED AND SIMPLIFIED.
Try the XDAdevelopers application!
curiouswrecker said:
This is what i gathered for you guys as a possible fix, it would work 100% if you guys didn't mess with EVERYTHING IN ODIN!
Because i have tested it myself several times.
READ EVERYTHING CLEARLY
4# When you mess with an s6 to the point that it does not turn on anymore and it only reacts until you plug it into a computer then it shows a screen "error occurred during update use Smart Switch..."
Well by that point Smart Switch mode partially takes over and you can only flash the device successfully in Smart Switch mode using Odin on the computer NOT Smart Switch.
(this knowledge may be useful later)
!!! PART 1 !!!
Here we go, follow this in detail.
STEP 1. You need to download the original Odin 3.10.6 from XDA here below:
http://forum.xda-developers.com/attachment.php?attachmentid=3109599&d=1420980613
STEP 2. Download the Kernel below:
http://mirror31.downloadandroidrom....nibase/S6-UniBase_BOG8_v2.tar?token=514002462
STEP 3. Open Odin on your computer as administrator.
STEP 4. Now connect your device to your computer, put your device/phone in Odin mode.
(volume down, home and power)
STEP 5. Make sure Odin has detected the device.
STEP 6. Load the Kernel in "AP" and wait 1 minute, then click START.
It should say PASS! However if it does not succeed, reboot the device and try it again in Smart Switch mode.
(It should actually pass the first try if these simple instructions are followed properly)
_____________________________________________
!!!PART 2!!!
STEP 1. Download this Firmware below:
http://www.sammobile.com/firmwares/download/62003/G925FXXU3QOKN_G925FVFG3QOKN_VDF/
STEP 2. Open Odin as administrator.
STEP 3. Connect your device to your computer, Put your device/phone into Odin mode.
(volume down, home, power)
STEP 4. Make sure Odin has detected your device.
STEP 5. Load the Firmware in Odin "AP" and wait a few minutes, when Odin is done reading the file click on START and install the Firmware.
!!! IMPORTANT !!!
1st Possibility, if Odin shows "FAIL" "hidden.img" then that's a GOOD THING!
your phone is allmost fixed.
(Let me know if that happens.)
2nd Possibility, if Odin stops at "Nand Write" you must start over, unplug your device make sure it's OFF, then plug it back in to the computer in order to boot the DEVICE into SMART SWITCH MODE and then follow the 5 STEPS again ONLY THIS TIME DO NOT BOOT THE DEVICE INTO ODIN MODE! Leave it in SMART SWITCH MODE.
(read above "4#")
If Odin shows "PASS" then DO NOT UNPLUG the DEVICE! Go get yourself a coffee your device should be perfectly fixed!
!!! LET US KNOW !!!
You can proceed rooting your device ask for help for a complete root guide.
Try the XDAdevelopers application!
Click to expand...
Click to collapse
I did flash that UniBase kernel and because of this I've lost the Imei number... I had to use Jtag box to recover the Imei.
so Beware when flashing this kernel.
I will try to flash the stock rom from sammobile... Hope it will help.
curiouswrecker said:
You mean this post? It isn't clear enough, if you want help answer the questions people ask otherwise no one can help you.
And look, we are not talking about the device but we are talking about ODIN! Does ODIN fail or succeed flashing?
IF ODIN SUCCEEDS WITH FLASHING, THEN TELL ME!
SUCCEEDS Like This;
https://kpmgsecurity.files.wordpress.com/2014/12/odin-pass-autoroot.png
Or
FAILS Like This; http://ajqi.com/wp-content/uploads/...or-and-nand-erase-all-for-Samsung-devices.jpg
OKAY?
Click to expand...
Click to collapse
when I flash it passes in Odin...
only problem is - the device stuck on the first logo (powered by android).
and on download mode it shows:
Current Binary: samsung Official
System status: custom
and on recovery it shows:
dm-verity vertification failed... need to check DRK first...
I did some research also
http://forum.gsmhosting.com/vbb/f77...drk-device-root-key-not-shoving-imei-1991601/
and
http://forum.gsmhosting.com/vbb/f684/dm-verity-verification-failed-1974767/
I'm not sure what is this rootkey issue, someone said that it is damaged, therefore it shows the dm verity vertification failure.
Entebox said:
http://forum.gsmhosting.com/vbb/f77...drk-device-root-key-not-shoving-imei-1991601/
and
http://forum.gsmhosting.com/vbb/f684/dm-verity-verification-failed-1974767/
I'm not sure what is this rootkey issue, someone said that it is damaged, therefore it shows the dm verity vertification failure.
Click to expand...
Click to collapse
found another thing, will give it a try:
http://forum.xda-developers.com/not...rification-t3293306/post64808458#post64808458
I also got the "dm verity vertification failure" today, but with me it happened because I was dumb enough to flash a G920I modem and bootloader on my G925F...
So it also bootlooped and everything, and then just like what you had, it asked me for Smart Switch. But then when I used Smart Switch on it, I got firmware from a totally different country than my own (think it was from Mexico or something), as I live in the Netherlands. And it even asked me for my phone's serial number before Smart Switch went on and flashed that firmware.
So I guess they only look at the CSC or something? Anyway, after that I got it into download mode and immediately flashed the newest correct firmware, and am happily flashing ROM's again Just download your own country's 5.1.1 firmware and you'll be alright, as long as you can get into download mode
Piliip said:
I also got the "dm verity vertification failure" today, but with me it happened because I was dumb enough to flash a G920I modem and bootloader on my G925F...
So it also bootlooped and everything, and then just like what you had, it asked me for Smart Switch. But then when I used Smart Switch on it, I got firmware from a totally different country than my own (think it was from Mexico or something), as I live in the Netherlands. And it even asked me for my phone's serial number before Smart Switch went on and flashed that firmware.
So I guess they only look at the CSC or something? Anyway, after that I got it into download mode and immediately flashed the newest correct firmware, and am happily flashing ROM's again Just download your own country's 5.1.1 firmware and you'll be alright, as long as you can get into download mode
Click to expand...
Click to collapse
yeah... already flashed the newest for my country.. it flashes well but still stuck on logo after.
from some reason after flashing, on DL mode it shows :
Current Binary: samsung Official
System status: custom
so the system status refuses to become official. even after using the smartswitch software.
I think maybe some of the partitions in the eMMC are corrupted.
Entebox said:
yeah... already flashed the newest for my country.. it flashes well but still stuck on logo after.
from some reason after flashing, on DL mode it shows :
Current Binary: samsung Official
System status: custom
so the system status refuses to become official. even after using the smartswitch software.
I think maybe some of the partitions in the eMMC are corrupted.
Click to expand...
Click to collapse
I think that's because you've tripped knox (hence custom), but you do have official samsung firmware, (hence official).
Edit: Have you checked your kernel?
Btw IMPORTANT when you say that you "flash" the device through odin are you referring to the pictures on your thread where the logg states that it failed on "nand write" and once on "hidden.img" or did it actually pass after the complete flashing of all the files "hidden.img" included?
succesful flashes i mean passes, i can get many many stock files to flash and pass no problem now as wasnt the case when i first got the phone
It shows you this type of screen (1st)
http://www.pocketpc.ch/attachments/s...210_155028.jpg
thats the first screen i can never ever get past
(does it say kernel isn't seandroid enforced?) it doesnt say that... but previously when i was flashing twrp and booted tried booting the phone up it woud say recovery isnat seandroid enforcing, i dont get that no more as i am flashing stock firmwares
---------- Post added at 01:17 PM ---------- Previous post was at 01:06 PM ----------
Entebox said:
I did flash that UniBase kernel and because of this I've lost the Imei number... I had to use Jtag box to recover the Imei.
so Beware when flashing this kernel.
I will try to flash the stock rom from sammobile... Hope it will help.
Click to expand...
Click to collapse
im willing to try that method above too... but am worried about losing the imei mentioned, have also read that happen to someone else and they fixed it too but they didnt mention how, and a worried to try it too as wouldnt know how to fix the imei if it went wrong as u mentioned u used soemthing called jtag to recover and i have no idea what or how that is
Entebox said:
I did flash that UniBase kernel and because of this I've lost the Imei number... I had to use Jtag box to recover the Imei.
so Beware when flashing this kernel.
I will try to flash the stock rom from sammobile... Hope it will help.
Click to expand...
Click to collapse
NO!!!
This is the UnibaseV9 Kernel, i have tested all the files i've shared on this thread personally on Samsung s6 edge model SM-G925F!
I never lost any imei!
Just follow the steps for God's sake!