Hey, been on these forums for a while, I rarely ask for help (been pretty lucky with the phones), but I have a question.
My phone won't charge. Or rather, it requires a time consuming process of fiddling, unplugging, replugging, and sometimes minor surgery on the USB port with a toothbrush or a tool I've crafted out of a Q-tip. However, after a night of charging (or some interrupted equivalent that results in a charged battery) the battery quickly depletes while still plugged in.
This is most clearly illustrated when yesterday, at 8:45 I rolled over and checked my phone to see if it had been charged. Pleased to see that it had been charged up to 100% I fell back asleep. When I woke up again to go to school at 9:10, my phone was entirely dead. I couldn't even get it to turn on to the point where it showed the I9100 screen. After following the time consuming and frustrating process of fiddling with the USB port and Micro USB charger, I coaxed the phone to show the powered-down charging screen, where I left it to charge to full.
I have been experiencing this over the course of a few weeks and I have tried many chargers, but only one of them will work at all (Interestingly a Motorola cord). Upon inspection of the USB port, nothing seems out of the ordinary, though the 2 prongs on the outside of the USB port male receiver look slightly different than the inside 2, though they difference is symmetrical.
Does anybody have any idea of what could be plaguing my phone? USB or battery? This is my second SII, a replacement one after my original one was tragically lost in a hot tub . Any thoughts would be awesome.
Thanks
Braidonh
If you are using Siyah kernel have you altered the charging current through EsTweeks?
If so then it is possible that the battery / charging circuit has been damaged. Try resetting the values to default (I think its 700mV on AC and misc and 600mV on USB but dont quote me).
Failing that then some hardware trouble shooting (trying a new battery / external battery charger) will help you figure out what is going on.
Ccarlpearce said:
If you are using Siyah kernel have you altered the charging current through EsTweeks?
If so then it is possible that the battery / charging circuit has been damaged. Try resetting the values to default (I think its 700mV on AC and misc and 600mV on USB but dont quote me).
Failing that then some hardware trouble shooting (trying a new battery / external battery charger) will help you figure out what is going on.
Click to expand...
Click to collapse
My signature is quite outdated... Currently just running CM 10.1 with stock everything. Haven't tweaked anything in that capacity... but will try my other battery (if I can find it). Thanks!
I was having this same problem with my HTC vivid. I tried charging with may chargers, the phone claimed it was charging (orange light lit up) but the phones battery was dying while plugged in. Just like you said, the battery depleted rather quickly when plugged in. Since my phone refused to accept any form of charge I bought an external battery charger and some extra batteries.
However, last week I wondered if maybe there was some sort of dust, or small pieces of sand inside the Micro-USB port on my in my phone that were possibly "blocking" the charger from properly charging.
So I bought an air duster and blew air into the USB port of my phone. I guess there must have been something in there because that fixed my issue and now my phone charges!
Now I have 4 batteries for my phone and an external battery charger.
Try it on your phone, see if you have the same luck I had.
Braidonh said:
My phone won't charge. Or rather, it requires a time consuming process of fiddling, unplugging, replugging, and sometimes minor surgery on the USB port with a toothbrush or a tool I've crafted out of a Q-tip.
Does anybody have any idea of what could be plaguing my phone? USB or battery?
Braidonh
Click to expand...
Click to collapse
Maybe I'm missing something here because you seem to be experienced on this forum and understand about searching first.
Anyway, this sounds like the common USB problem that S2s have. It can be the jack or more typically, the flex cable. You replace the little board. Search for USB in this forum. I just changed mine with one I got on Ebay. Cheap and easy.
Related
as i tire of hunting for hours for a thread i post. here goes...
for some unknown reason my g4 8125 wont charge. it went dead on the charger and i was thinking that my wall charger had freaked out. well after about a day of sitting i hit the power button and the lights came on! well it was a built up charge so i know the phone didn't brick. i put it on the usb cable to see if the red light would come on and no such luck.
any ideas? r they known for suddenly ignoring the charger??? any help is great!
oh and i haven't modded anything but the carrier unlock.
*i found on ebay a few that were selling with the charger port "broken" ... this a common thing? it able to be fixed if so?
rubledub said:
as i tire of hunting for hours for a thread i post. here goes...
for some unknown reason my g4 8125 wont charge. it went dead on the charger and i was thinking that my wall charger had freaked out. well after about a day of sitting i hit the power button and the lights came on! well it was a built up charge so i know the phone didn't brick. i put it on the usb cable to see if the red light would come on and no such luck.
any ideas? r they known for suddenly ignoring the charger??? any help is great!
oh and i haven't modded anything but the carrier unlock.
*i found on ebay a few that were selling with the charger port "broken" ... this a common thing? it able to be fixed if so?
Click to expand...
Click to collapse
I had a similar issue a few months back. It happens that the wizard needs a minimum charge on the battery in order to being able to charge. It´s like the charging connection is made by internal software.
Probably you drained too much the battery to a point that it no longer can sustain the cellphone on enough time so it recognizes the charger and it starts charging.
The workaround would be to jumpstart the battery.
There´s a post on thiss matter but in order to give you a straigth answer, you will need to find a low voltage source (better of 5volts or less, DC). Many users have used the usb port on their pcs, cutting out a cable.
Then you will need to remove the battery from the phone, and find the (+) and (-) sing. Probably you will find that there are more than 2 power connections on the battery. I assumed that the + and + were the most outer ones and it worked for me.
Then you would need to "connect" the power source cables to the battery. Beware of the polarity. keep the cables there for about 5-8 minutes so the battery would have a charge on it.
I personally used as a power source, a small 4 AA NiM rechargeable battery pack that gave me 1.2 volts x 4, meaning 4.8 volts. So even when the battery is only 3.7volts, a 5 volts power supply as the USB port, would do the trick. Just be carefull not to overcharge the battery. If you feel that the battery is getting hot, then probably something went wrong and you must stop and recheck the polarity. After 5 minutes the battery shouldn´t heat up too much on a 5volts surge.
To use the USB you just need to cut out an old usb cable that you don´t use (from an old mouse, or anything similar. Find the black and the red cables (the green and white are data cables, so don´t mess with those). and use them to connect to the battery with your fingers.
Tell us how it went.
thanks as always you guys are like the boy scouts...always prepared!
at least i think that's their motto...isn't it? anyway thanks a million
Strange as idea but i try to post here hoping that someone can help me.
Basically i buyed times ago this desktop charger http://cgi.ebay.com/Battery-Desktop...ewItem&pt=PDA_Accessories&hash=item414fc27090
Unfortunatly yesterday i don't know what happen but it get burned.
Is it possible to connect somehow the usb cable directly on the 2 tooth where allocate the battery?
I tryed to open it and seems that only the part with Ac alimentation get burned, via usb is working as well the only problem is that opening it accidentally i removed als o the 2 small cables that go from the internal board to the thooths.
I wouldn't connect the usb cable directly to the terminals to charge the battery since USB is 5V and the battery is 3.7V without an overcharge protection circuit.
Doing without could result in damage to the USB on the computer or adapter which you are charging from. It will damage the battery and could cause a fire.
I use that exact same charger... can you explain the "burn" part? I am slightly concerned now as I leave this to charge over night while I am asleep.
SolemnWishing said:
I use that exact same charger... can you explain the "burn" part? I am slightly concerned now as I leave this to charge over night while I am asleep.
Click to expand...
Click to collapse
well i simple plugged in and started to feel a burned smell. Is not working anymore.
Desktop Charger
This will give you a dock and spare battery charger. I was bored and browsing last night and saw it. I haven't used it. I may get one myself. Deal Extreme
Here is just the charger for a little less $$ Best Offer Buy
Hi I want to ask for help. I bought my htc touch pro 2 T 7373 from ebey but only phone with no charger.I bought HTC Power Supply model: TC P300 output: 5V-1A LPS Pin 1+ , Pin 4- .When I put it to charge , phone indicates to charge ,but battery does not charge.Battery is new and I dont think the problem is it.I want to ask you if this charger is compatible with HTC TOUCH PRO 2 T7373.
russslannn said:
Hi I want to ask for help. I bought my htc touch pro 2 T 7373 from ebey but only phone with no charger.I bought HTC Power Supply model: TC P300 output: 5V-1A LPS Pin 1+ , Pin 4- .When I put it to charge , phone indicates to charge ,but battery does not charge.Battery is new and I dont think the problem is it.I want to ask you if this charger is compatible with HTC TOUCH PRO 2 T7373.
Click to expand...
Click to collapse
Just use a miniUSB cable and plug it into your computer. Any USB wall charger should work. I've used iPhone USB chragers with a miniUSB cable, Nikon camera chargers, as well as a Motorola one. You just need to plug it into any USB port either on a wall or on your computer. Leave the device off while it charges overnight.
Problem with charged
I use both ways but no result , phone indicates to charged but battery not charging.Charger is original and consists of two parts: the charger and mini usb cable .When i run it sometimes on the displays show this message : The charging current is not enough for device power consumption.Please shut down unused applications , or switch to AC adapter. And I do not use any applications. I tried to load phone in the off position , indicates that the charger is ON but the battery is not charging .Please help if someone has the same problem
russslannn said:
I use both ways but no result , phone indicates to charged but battery not charging.Charger is original and consists of two parts: the charger and mini usb cable .When i run it sometimes on the displays show this message : The charging current is not enough for device power consumption.Please shut down unused applications , or switch to AC adapter. And I do not use any applications. I tried to load phone in the off position , indicates that the charger is ON but the battery is not charging .Please help if someone has the same problem
Click to expand...
Click to collapse
Try it with a different miniUSB cable. If you don't have one handy, miniUSB cables go for pennies on Amazon or eBay. You can find them in retail stores for about 10 dollars or so as well. If the cable isn't the problem, then it is either a problem with the charge port on the device, or the battery. It's far cheaper to trouble shoot the cable, so let's just start with that.
Sound like the charger is insufficient power, even though it says 1A. Try charging from a computer USB port and see if it charges. HTC don't list TP2 as suitable for this charger.
I am also facing same problem. LED shows charging but phone does not charge. And when I insert charger "USB TO PC" page shows up, Like I have connected the phone to PC.
Please Help...
I just had an issue charging which turned out to be an easy fix.
The led would come on and the icon would show charging but it wasn't increasing the battery %. Then I would get a message about the power not being enough and to plug it into a charger. I tried several chargers and was getting the same thing happening. I blew a few puffs into the charging port which looked clean and it was still happening. I wiggled the cable/plug in the port and occassionally the charging light would go on and off. The charging led even started to go on and off with the phone just sitting still on my table. I feared that my charging port had gone bad so I ordered 2 spare batteries and battery charger from ebay for $10 (works well and battery life good).
While waiting for the ebay purchase to arrive I did some reading up and saw that pins could be bent etc. In my fustration I used a pair of tweezers to gently scrape the charging port pins/contacts (in a straight direction). Then I used an old toothbrush and firmly brushed out the usb port - a whole bunch of lint and stuff come out of the port even though it had previously looked clean.
I plugged in my charger and bingo! My charging issue was gone.
ukexport said:
I just had an issue charging which turned out to be an easy fix.
The led would come on and the icon would show charging but it wasn't increasing the battery %. Then I would get a message about the power not being enough and to plug it into a charger. I tried several chargers and was getting the same thing happening. I blew a few puffs into the charging port which looked clean and it was still happening. I wiggled the cable/plug in the port and occassionally the charging light would go on and off. The charging led even started to go on and off with the phone just sitting still on my table. I feared that my charging port had gone bad so I ordered 2 spare batteries and battery charger from ebay for $10 (works well and battery life good).
While waiting for the ebay purchase to arrive I did some reading up and saw that pins could be bent etc. In my fustration I used a pair of tweezers to gently scrape the charging port pins/contacts (in a straight direction). Then I used an old toothbrush and firmly brushed out the usb port - a whole bunch of lint and stuff come out of the port even though it had previously looked clean.
I plugged in my charger and bingo! My charging issue was gone.
Click to expand...
Click to collapse
That was the biggest problem with MiniUSB was the width and height of those ports. It's a haven for stray dust and dirt. They need to be brushed out every so often, especially when you just drop it in you pocket.
hi buy and it schould work
buy a new charging cable
ukexport said:
I just had an issue charging which turned out to be an easy fix.
The led would come on and the icon would show charging but it wasn't increasing the battery %. Then I would get a message about the power not being enough and to plug it into a charger. I tried several chargers and was getting the same thing happening. I blew a few puffs into the charging port which looked clean and it was still happening. I wiggled the cable/plug in the port and occassionally the charging light would go on and off. The charging led even started to go on and off with the phone just sitting still on my table. I feared that my charging port had gone bad so I ordered 2 spare batteries and battery charger from ebay for $10 (works well and battery life good).
While waiting for the ebay purchase to arrive I did some reading up and saw that pins could be bent etc. In my fustration I used a pair of tweezers to gently scrape the charging port pins/contacts (in a straight direction). Then I used an old toothbrush and firmly brushed out the usb port - a whole bunch of lint and stuff come out of the port even though it had previously looked clean.
I plugged in my charger and bingo! My charging issue was gone.
Click to expand...
Click to collapse
I was facing the same charging problem and was looking for a solution. And i found this forum and read it and did the same thing and my problem is fix.. I can charge my mobile now. Thanks a lot for the great help.
Sarchy Minimum
All of these dumb charges, ie bricks in the wall, use the unused USB pins to communicate how much power they can provide. There are some resistors they put on the D-/D+ to say this is a 700ma charger or whatever. Trouble is that there are limited standards on these resistors so it's more than possible that a phone will charge but not enter high current charging when attached to a new brick in the wall. The cables however are more universal.
Hello XDA,
I'm not sure how this happened, but for the past couple of months I haven't been able to charge my phone while it is turned on. It shows the charging animation but the battery still drains, even with all radios off and screen off. I can leave it charging all night and end up with a nearly flat battery. Plugging it in to any wall socket seems to only slow the draining, and plugging it in to a fully powered USB socket (many tried) keeps it at the same battery level, or very slowly charges it if I don't use it. If I turn it off however, I can charge it until full in the normal time with the original AC charger.
Here's the really strange part: I've tried several new chargers of different brands including samsung and it makes no difference. Not only that, but they won't charge it when powered off either making them completely ineffective. It doesn't initialize the charge properly - the screen either shows a battery with a progress circle over and over again without getting to the charging animation, or displays the charging animation over and over and never charges at all, but nevertheless gets hot.
The chargers I've tried are:
Cygnet for samsung phones including SGS-II
Belkin for Samsung phones including SGS-II
Premium blackberry travel charger
Premium 10W 2A Samsung travel adaptor
One charger that did seem to work while plugged in was from a new Sony Xperia Windows phone charger I borrowed once.
I've exchanged at the store 3 times now with the same result! It must be something wrong with the hardware or software...
I've calibrated the battery, I've had a new battery for a couple of months and normally still lasts all day and more on a full charge. It is a 3rd party high quality Anker battery. The problem is the battery is getting a lot more taxed now that I'm using 3G over the portable hotspot, so its not quite lasting the day anymore.
I've had countless custom ROMs on there now, current ROM is CyanogenMod 10.1 stable. Would returning to stock then reinstalling help?
Something that shouldn't matter is I've moved from the UK to Australia. I'm still using the English charger as its the only one that works. And the Xperia charger that seemed to work was Australian too.
Before it got this bad I think it was getting slower and slower to charge. I had to replace the old USB cable that eventually got really loose, then broke and i've tried several new ones with no improvement in charging ability. Is it possible that the contacts inside the micro-USB socket might have been bent from the old cable moving around so much so that only minimal contact is achieved with any other cable? The new connectors do seem to fit perfectly.
In the attached screenshot, you will see on the left the AC charger is plugged in while battery level goes down, then on the far right its plugged in to a computer and is kept level.
Any suggestions would be greatly appreciated!!
sevenlions said:
Hello XDA,
I'm not sure how this happened, but for the past couple of months I haven't been able to charge my phone while it is turned on. It shows the charging animation but the battery still drains, even with all radios off and screen off. I can leave it charging all night and end up with a nearly flat battery. Plugging it in to any wall socket seems to only slow the draining, and plugging it in to a fully powered USB socket (many tried) keeps it at the same battery level, or very slowly charges it if I don't use it. If I turn it off however, I can charge it until full in the normal time with the original AC charger.
Here's the really strange part: I've tried several new chargers of different brands including samsung and it makes no difference. Not only that, but they won't charge it when powered off either making them completely ineffective. It doesn't initialize the charge properly - the screen either shows a battery with a progress circle over and over again without getting to the charging animation, or displays the charging animation over and over and never charges at all, but nevertheless gets hot.
The chargers I've tried are:
Cygnet for samsung phones including SGS-II
Belkin for Samsung phones including SGS-II
Premium blackberry travel charger
Premium 10W 2A Samsung travel adaptor
One charger that did seem to work while plugged in was from a new Sony Xperia Windows phone charger I borrowed once.
I've exchanged at the store 3 times now with the same result! It must be something wrong with the hardware or software...
I've calibrated the battery, I've had a new battery for a couple of months and normally still lasts all day and more on a full charge. It is a 3rd party high quality Anker battery. The problem is the battery is getting a lot more taxed now that I'm using 3G over the portable hotspot, so its not quite lasting the day anymore.
I've had countless custom ROMs on there now, current ROM is CyanogenMod 10.1 stable. Would returning to stock then reinstalling help?
Something that shouldn't matter is I've moved from the UK to Australia. I'm still using the English charger as its the only one that works. And the Xperia charger that seemed to work was Australian too.
Before it got this bad I think it was getting slower and slower to charge. I had to replace the old USB cable that eventually got really loose, then broke and i've tried several new ones with no improvement in charging ability. Is it possible that the contacts inside the micro-USB socket might have been bent from the old cable moving around so much so that only minimal contact is achieved with any other cable? The new connectors do seem to fit perfectly.
In the attached screenshot, you will see on the left the AC charger is plugged in while battery level goes down, then on the far right its plugged in to a computer and is kept level.
Any suggestions would be greatly appreciated!!
Click to expand...
Click to collapse
IMO, u should revert back to a stock samsung Firmware (pertained to ur region) and then see if the issue persists or not to rule out any possible 'Software issue' in the first place
Thank you, I will try that and report back the results.
You can try hawkerpauls nuke if flashing stock doesn't work: http://forum.xda-developers.com/showthread.php?t=2100558
Hi my s3 is no longer charging. The USB micro port is damaged.
I am not anywhere near my home at the moment and I really need the phone. So I made the most ghetto charger known to man. Which is basically just a stripped USB cable attached to some paperclips acting as springs to charge the battery when it is removed from the phone. This actually works surprisingly well and consistently charges to 88% in a bit over an hour.
However, what I'm really interested in (and I want to stress that this is only a temporary solution while I'm travelling) is what are the two gold pins in the middle, left on the back of the phone for?
I believe they are for attaching an extended battery to the back of the phone.
However I can't find any information on them, nor do I have a multimeter with me.
Can I just apply 4.5 volts to these two pins so I can charge my phone while using it?
Also which is positive and which is negative.
I just need a quick and dirty solution, thanks.