Related
I have a malfunction usb connector so usb data transfer or my jig is not working anymore. The data cable and the jig is tested on another I9100, and they worked well. Surprisely the 3key download mode is working, and firmware flash with odin too.
So I need an alternate way to reset the counter before I send it back to warranty service
Is it stored in the bootloader? Can I reflash it with odin?
KeFe said:
I have a malfunction usb connector so usb data transfer or my jig is not working anymore. The data cable and the jig is tested on another I9100, and they worked well. Surprisely the 3key download mode is working, and firmware flash with odin too.
So I need an alternate way to reset the counter before I send it back to warranty service
Is it stored in the bootloader? Can I reflash it with odin?
Click to expand...
Click to collapse
there is no known alternative way of resetting the counter, if it was as simple as using odin then we would have never worried about using a jig.
So then what is the best way to make a total brick? (result: no 3key recovery or download mode)
I should mess with the bootloader in odin?
KeFe said:
So then what is the best way to make a total brick? (result: no 3key recovery or download mode)
I should mess with the bootloader in odin?
Click to expand...
Click to collapse
LOL!! This is the reverse "I bricked my phone" thread. It's the first time I've seen someone asking how to brick their phone.
I suggest you look at the above mentioned "Hallppz!! I broked mi fonnee" threads and do exactly what they did to brick their phones. Stuff like flashing SGS firmware on SGS2 can help.
aydc said:
LOL!! This is the reverse "I bricked my phone" thread. It's the first time I've seen someone asking how to brick their phone.
I suggest you look at the above mentioned "Hallppz!! I broked mi fonnee" threads and do exactly what they did to brick their phones. Stuff like flashing SGS firmware on SGS2 can help.
Click to expand...
Click to collapse
Can help, but will be detectable. just start a flash with odin and unplug halfway through, you'll get a connect to pc screen and wont be able to acces download mode
It is the first destructive thread in this forum, isn't it?
dh2311 said:
Can help, but will be detectable. just start a flash with odin and unplug halfway through, you'll get a connect to pc screen and wont be able to acces download mode
Click to expand...
Click to collapse
Thx
I'll try it tomorrow in the evening unless somebody comes up with a better idea.
I'll post here the result
AFAIK, samsung service center won't check for "flashed" phones. When I returned my SGS2(just cf-rooted), they said I should return after 30mins because they'll flash it back to default(They didn't even check, they just said that while I was still filling-up their repair form). But my yellow tint was still there, so I got a new phone. Now no yellow tint visible on the eyes.
gr8... hope i
dont hav to visit warrnty ever..
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to Q&A
Hello, I was attempting to flash Clockwork Mod on my G5, whilst doing it Odin crashed and now my phone is messed up.
It will turn on but a PC-Triangle with a ! in the middle-Phone, it will go into Download Mode but Odin doesn't recognise it so i can't re-flash it, any ideas?
Please help, this is urgent.
The phone itself is on stock, it turns on but displays the error i have described above, it will go into download mode but Odin doesn't recognsie it.
Thanks, Curtis.
CurtisAndroid5 said:
Hello, I was attempting to flash Clockwork Mod on my G5, whilst doing it Odin crashed and now my phone is messed up.
It will turn on but a PC-Triangle with a ! in the middle-Phone, it will go into Download Mode but Odin doesn't recognise it so i can't re-flash it, any ideas?
Please help, this is urgent.
The phone itself is on stock, it turns on but displays the error i have described above, it will go into download mode but Odin doesn't recognsie it.
Thanks, Curtis.
Click to expand...
Click to collapse
No need to worry about it.
Uninstall the drivers associated with the phone. Are you using Windows?
For XP: Go to start > Control Panel > System > Click on the Hardware tab and then Device Manager. Find the driver for the phone. I remember it has a yellow icon, and the drivers name is a mix of capital letters
It's probably similar for Windows 7, but i wouldn't know.
Uninstall the driver associated with the phone, then reinstall by plugging your phone into the computer in download mode. It would help to uninstall and reinstall Odin as well, just in case.
If you get Odin to work, just work away like you would.
Thanks for your reply, i have uninstalled the drivers, but when i plugged my phone back in, the drivers are not being installed and i can not find them on the internet. Any ideas?
I know how i messed up, i completely forgot to root my phone before i started to flash, any ideas on how i can just get my phone back to its normal working everyday self?
Will i just need to get the device recognised by Odin then insert the Ops file and the I5500.tar file and flash it back to stock?
edit- managed to get drivers installed, now how do i fix my phone? Just flash the .OPS and the stock I5500.tar file?
CurtisAndroid5 said:
Thanks for your reply, i have uninstalled the drivers, but when i plugged my phone back in, the drivers are not being installed and i can not find them on the internet. Any ideas?
I know how i messed up, i completely forgot to root my phone before i started to flash, any ideas on how i can just get my phone back to its normal working everyday self?
Will i just need to get the device recognised by Odin then insert the Ops file and the I5500.tar file and flash it back to stock?
edit- managed to get drivers installed, now how do i fix my phone? Just flash the .OPS and the stock I5500.tar file?
Click to expand...
Click to collapse
I think it'll fail again if your phone isn't rooted. You can't get rid of the Computer-Caution-Phone image without succesfully using Odin.
You could try to flash the .tar and .ops file again. I can't see it working though unfortunately.
Any ideas then? Is there a way to root my phone via Odin or anything?
CurtisAndroid5 said:
Any ideas then? Is there a way to root my phone via Odin or anything?
Click to expand...
Click to collapse
I've never heard of rooting your phone through the download mode or through Odin.
Maybe there's a file you can put on your phone through Odin which doesn't require root? I'll take a look around for you.
Thank you so much, i appreciate it, I'm 16, can't really live without a phone especially with college parties coming up in the next few days aha, I knew i shouldn't of risked around with flashing again!
CurtisAndroid5 said:
Thank you so much, i appreciate it, I'm 16, can't really live without a phone especially with college parties coming up in the next few days aha, I knew i shouldn't of risked around with flashing again!
Click to expand...
Click to collapse
Just thinking that Odin is a program which requires root so there won't be any file you can transfer when unrooted. I had a quick glance over at the Odin thread, and the first step is that you have to root your phone.
I'm sorry, but there's nothing else I can think of which might help. Maybe if somebody with a bit more knowledge/expeerience sees this thread, they might help.
Can Odin detect your phone?
Ah man, thanks anyway, yes Odin detects my phone, I'm trying to use SuperOneClick Root on my PC- Do you know any other Root software that works on PC?
CurtisAndroid5 said:
Ah man, thanks anyway, yes Odin detects my phone, I'm trying to use SuperOneClick Root on my PC- Do you know any other Root software that works on PC?
Click to expand...
Click to collapse
I don't know of any others, but Superoneclick works fine for the Galaxy 5. Like I said, I've never heard of using it during download mode so just be careful with that.
If Odin detects your phone, have you tried just closing Odin and plugging out the USB safely?
Can't use Superoneclick as my phone isn't in USB Debugging and i obviously can't change that aha I have just tried that, no luck with the closing Odin and unplugging it, should i try installing CWM again or is that a bad idea?
CurtisAndroid5 said:
Can't use Superoneclick as my phone isn't in USB Debugging and i obviously can't change that aha I have just tried that, no luck with the closing Odin and unplugging it, should i try installing CWM again or is that a bad idea?
Click to expand...
Click to collapse
It's a bad idea because it just won't work. Odin will crash again.
I don't know what to do I'm afraid.
Looks like my phone is shagged due to my own stupidity, I forgot to root it because my phone was previously rooted and it went back for repairs, then I completely forgot i didnt install Root access -.-
Do you think i can recover my phone or is it well and truly gone?
Well it's not like your phone is bricked or anything. It's just broken a connection to Odin and it won't boot until it's completed.
You could always return it for repairs again. Your warranty might be broken though.
If I happen to come across a DIY fix then I'll post it here.
Thanks for your help mate, i've decided to just send my phone back for repairs, buy a new phone (Probably a Blackberry for BBM and stuff with all my mates), and sell my phone once i get it back.I have gave up on Samsung mobiles.
Thank you.
Did you send your phone alredy? Uncompress the firmware.tar file and unselect "one package in Odin" . On the boot in odin select the boot file of the .tar and run odin. Maybe that will help
Sent from my Galaxy5 using XDA App
Dude have u tryd using samsung kies it might detect it n let u do an emergancy firmware recovery or maybe (a verry unlikely maybe but still a maybe) it will detect the problem and provide u a solution hope this helps.
CurtisAndroid5 said:
Ah man, thanks anyway, yes Odin detects my phone, I'm trying to use SuperOneClick Root on my PC- Do you know any other Root software that works on PC?
Click to expand...
Click to collapse
Hi, had the very same issue as you. Odin crashed just few sec after start. What I did ; uninstalled everything (Odin & files comes with it, KIES). Then restart PC, go to Samsung.com and download latest KIES, when downloaded go to Tools and check for updates. Accept/run them, when done restart PC. Now, read the steps bellow, and see the attached picture.
1. Extract Odin v4.28 and Ops File.zip I5500XXXX.rar
2. Open Odin v4.28,
- Select OPS tab: EUROPA_v1.0.ops
- Make sure Auto Reboot & Protect OPS selected in Option tab
- get this I5500XFJPQ from samfirware.com ( for some strange reason only this package worked!), download, and unzipp to folder called GT-I5500. In to this folder place Odin and ops as well.
- Make sure One Package selected in Option tab
3. Turn off phone, remove battery for 5second, put it back
4. Hold "Volume Down, Center button & Power button" in the same time to enter Download Mode (yellow triangle)
5. Connect to PC with USB cable
6. When the data line and the phone connection is successful, com port shows yellow in Odin
7. Press Start on Odin
8. Waitin & Pray!
9. PASS, its done!
*Hard reset after flashing *2767*3855#
*Check ur Phone Info *#*#1234#*#*
Note: my i5500 was rooted, so if was yours then ok. When pressing buttons you must see an yellow triangle! If you don't see it don't try connect. Remove battery for 3-5 minutes and try again...
Thanks for the replies, I've got my 'broken' phone in its box on my wardrobe, Carphone Warehouse have ordered me a brand new G5 to replace mine, I should get that sometime next week, but I'm buying a HTC Wildfire S pretty soon anyway!
Thanks for your help, I'd rather keep my broken phone well, broke aha.
Have you tried flashing twrp recovery then using cf-autoroot?
Hello,
I am new to the S2 forum. I have purchased the phone on Dec 04. It came with firmware version 4.0.4.
The PDA was I9100XWLPW and CSC was I9100ODDLPC.
After a week, I flashed the leaked JB firmware XXLSJ and used PhilZ cwm6 kernel to obtain root.
I was not having any problems until today.
I was using the phone normally, it had about 60% battery. Suddenly it was not waking up ( The phone was not used for about 15min ). I tried removing the battery, all button combinations but was not booting normally or into recovery. I could get into the download mode by plugging the phone to the PC. Odin failed to flash the official FW and the JB leak. I followed the thread http://forum.xda-developers.com/showthread.php?t=1457458 and found out it was a corrupted NAND r/w function.
I tried doing all the steps given in the thread. Now my phone does'nt go into the download mode and does'nt show charging when plugged to a power source.
Can I recover my phone?
Please someone help me or guide me to a previous post that solves this problem!!
Edit: Samsung service has replaced the mother board!!
Doing the pit partition has resulted in my phone getting bricked!!
So people new to the forum, never do it :laugh:
Hi,
You said you couldn't access download mode, but can you access CWM recovery?
If you can then, you should wipe data/factory set, wipe cache and wipe Dalvik-cahe. after that you should re-flash your ROM.
If that doesn't work, maybe you should restore your CWM/Nandroid backup of your ROM before you flashed the JB leak XXLSJ, which in this case seems to be Stock ROM. (providing that you have backed it up in the first place)
Greetz and Happy new year
CashAndPotatoes said:
Hi,
You said you couldn't access download mode, but can you access CWM recovery?
If you can then, you should wipe data/factory set, wipe cache and wipe Dalvik-cahe. after that you should re-flash your ROM.
If that doesn't work, maybe you should restore your CWM/Nandroid backup of your ROM before you flashed the JB leak XXLSJ, which in this case seems to be Stock ROM. (providing that you have backed it up in the first place)
Greetz and Happy new year
Click to expand...
Click to collapse
I am unable to get into recovery mode also.
The phone does not respond to any button-combos or connecting to computer or a power source!!
Pradeep said:
I am unable to get into recovery mode also.
The phone does not respond to any button-combos or connecting to computer or a power source!!
Click to expand...
Click to collapse
HI,
today I wake up with the same problem.(Bug from the junary 1st???). I'm on Leak 4.1.2 too
Mi Galaxy sII don't charge the batery (loop from charge batery symbol) All the combination button don't wake up the phone.
The only thing seem working is the download mode. Don't try to connect to ODIN for the moment.
Any idea?
Pradeep said:
I am unable to get into recovery mode also.
The phone does not respond to any button-combos or connecting to computer or a power source!!
Click to expand...
Click to collapse
Remove battery for some time re insert it and see .
Or
Try a jig
leap before you think
Pradeep said:
Hello,
I am new to the S2 forum. I have purchased the phone on Dec 04. It came with firmware version 4.0.4.
The PDA was I9100XWLPW and CSC was I9100ODDLPC.
After a week, I flashed the leaked JB firmware XXLSJ and used PhilZ cwm6 kernel to obtain root.
I was not having any problems until today.
I was using the phone normally, it had about 60% battery. Suddenly it was not waking up ( The phone was not used for about 15min ). I tried removing the battery, all button combinations but was not booting normally or into recovery. I could get into the download mode by plugging the phone to the PC. Odin failed to flash the official FW and the JB leak. I followed the thread http://forum.xda-developers.com/showthread.php?t=1457458 and found out it was a corrupted NAND r/w function.
I tried doing all the steps given in the thread. Now my phone does'nt go into the download mode and does'nt show charging when plugged to a power source.
Can I recover my phone?
Please someone help me or guide me to a previous post that solves this problem!!
Click to expand...
Click to collapse
We already have plenty of topics about this why do you feel the need to create another? Your symptoms are no different to others and the answers are no different.
If you cant access download or recovery and cant power on then try a USB jig. If that doesnt work then you will need to take/send it for repair which will either be JTAG or complete mobo replacement.
Just because you create your own topic it doesnt mean answer is going to be any different.
Gediprime said:
HI,
today I wake up with the same problem.(Bug from the junary 1st???). I'm on Leak 4.1.2 too
Mi Galaxy sII don't charge the batery (loop from charge batery symbol) All the combination button don't wake up the phone.
The only thing seem working is the download mode. Don't try to connect to ODIN for the moment.
Any idea?
Click to expand...
Click to collapse
If you can access download mode, use it. Try re-flashing your kernel.
nikufellow said:
Remove battery for some time re insert it and see .
Or
Try a jig
leap before you think
Click to expand...
Click to collapse
JIG ???
Gediprime said:
JIG ???
Click to expand...
Click to collapse
Use the search button and use keywords "usb jig". Or google.
TheATHEiST said:
We already have plenty of topics about this why do you feel the need to create another? Your symptoms are no different to others and the answers are no different.
If you cant access download or recovery and cant power on then try a USB jig. If that doesnt work then you will need to take/send it for repair which will either be JTAG or complete mobo replacement.
Just because you create your own topic it doesnt mean answer is going to be any different.
Click to expand...
Click to collapse
I am sorry!! I am new to this forum and the phone being a recent purchase, i was very much desperate!!
I know the answer may not be different and the problem may not be new hence I've asked to guide me to the appropriate thread in my post!! No offence!!
Thanks for your reply. I will be taking the phone to Samsung Service tomorrow.
Gediprime said:
JIG ???
Click to expand...
Click to collapse
3 100k resistors + 1k resistor in series connected between 4 and 5 pins of a male usb end when plugged will get you into download mode in case of soft bricks .
leap before you think
TheATHEiST said:
We already have plenty of topics about this why do you feel the need to create another? Your symptoms are no different to others and the answers are no different.
If you cant access download or recovery and cant power on then try a USB jig. If that doesnt work then you will need to take/send it for repair which will either be JTAG or complete mobo replacement.
Just because you create your own topic it doesnt mean answer is going to be any different.
If you can access download mode, use it. Try re-flashing your kernel.
Click to expand...
Click to collapse
I try it but when a push up level button my phone loop again to charging symbol (without charging)
Sorry if this post is the same than another. For my part i'm just trying to find a solution. A have plenty of corporative information on my phone. I do my last backup one weeks ago :crying:
nikufellow said:
3 100k resistors + 1k resistor in series connected between 4 and 5 pins of a male usb end when plugged will get you into download mode in case of soft bricks .
leap before you think
Click to expand...
Click to collapse
In some of the posts, I've read that a JIG may not work on ICS based roms!!
Is this true?? Should I try a JIG first before I take the phone to Samsung Service??
I was on XXLSJ before the phone went dead!!
Gediprime said:
I try it but when a push up level button my phone loop again to charging symbol (without charging)
Sorry if this post is the same than another. For my part i'm just trying to find a solution. A have plenty of corporative information on my phone. I do my last backup one weeks ago :crying:
Click to expand...
Click to collapse
I had the same problem.. I could get into the download mode by:
1. Phone completely OFF state
2. Connect the USB cable to the phone and PC ( The battery charging indication has to come, atleast once )
3. Fire up ODIN
4. Get the phone into download mode ( Vol-down+home+Power ) while the phone is connected
5. The phone is now recognized by ODIN.
I could flash a kernel (tried siyah and Philz) but the phone was not booting.
While trying to flash Stock and XXLSJ, ODIN was getting failed at factoryfs.fs
After a few trys, the phone just went dead!!
Hope you can flash a firmware successfully :good:
Pradeep said:
In some of the posts, I've read that a JIG may not work on ICS based roms!!
Is this true?? Should I try a JIG first before I take the phone to Samsung Service??
I was on XXLSJ before the phone went dead!!
Click to expand...
Click to collapse
You are misinterpreting what you read. What you're referring to is resetting the binary counter, and no it doesn't work on ICS bootloader however it still works for putting device into download mode (unless its bricked).
nikufellow said:
3 100k resistors + 1k resistor in series connected between 4 and 5 pins of a male usb end when plugged will get you into download mode in case of soft bricks .
leap before you think
Click to expand...
Click to collapse
"Soft-brick" has absolutely no meaning, Your device is either "bricked" or it isnt. Its a made up term by n00bs when they cant get system to boot normally. Your devcie is only bricked when it wont power on or go into useable recovery+download modes. If you can simply use a jig or go directly into flashing a rom then your device is not bricked.
The "bricked" term is used far too loosely nowadays.
Pradeep said:
I had the same problem.. I could get into the download mode by:
1. Phone completely OFF state
2. Connect the USB cable to the phone and PC ( The battery charging indication has to come, atleast once )
3. Fire up ODIN
4. Get the phone into download mode ( Vol-down+home+Power ) while the phone is connected
5. The phone is now recognized by ODIN.
I could flash a kernel (tried siyah and Philz) but the phone was not booting.
While trying to flash Stock and XXLSJ, ODIN was getting failed at factoryfs.fs
After a few trys, the phone just went dead!!
Hope you can flash a firmware successfully :good:
Click to expand...
Click to collapse
Your phone died? you kiding ?
I'm using the leak version of Sammobile since 3 weeks... Why do you think the phone make a bad reaction now? why now?
Ok, you try to flash OFW and don't result. and then you flash again the XXLSJ ? and the phone colaspe?
What kind of roms do i flash? OFM or CFW ? ICS or JB ?
Well if a can connect with ODIN of course
A quick question!!
Is it possible that the phone can be revived (put into download mode) using a JIG if it is not starting at all for any key combinations and it is not showing charging animation when plugged into a computer or a power source??
Pradeep said:
A quick question!!
Is it possible that the phone can be revived (put into download mode) using a JIG if it is not starting at all for any key combinations and it is not showing charging animation when plugged into a computer or a power source??
Click to expand...
Click to collapse
Yes its possible which is the reason we already mentioned to try it
It all depends on the actual base issue though as to whether it will work. Its worth a try either way though, They only cost £1-2 or you can make them yourself if you have the spare parts. (Don't ask how, Use search).
I have tried the JIG, but no luck!!
I have given the phone to Samsung Service.
Hope they fix it!!
Will they use JTAG or it has to be done somewhere else in case Samsung people refuse to do it??
They wouldn't refuse just act dumb tell something like you were updating firmware via kies and all of a sudden power went down and device bribed
leap before you think
nikufellow said:
They wouldn't refuse just act dumb tell something like you were updating firmware via kies and all of a sudden power went down and device bribed
leap before you think
Click to expand...
Click to collapse
Thanks!! Well I did act dumb there!! Said I downloaded a game Royal Revolt (~200 MB), the phone got heated, blah blah blah......
Well I did not tell about firmware upgrade via kies and all....
Only thing that I can do now is wait and hope!!:laugh:
When I turned on my i9300 galaxy III phone last week it prompt me for an upgrade. I installed it and as soon as it booted again, every single app started to issue warnings about stopping. The phone cycles through all of these pop up warnings over and over again and never reaches the home screen.
What I have tried:
Plugged it to PC open Kies - drivers were not installed correctly, Kies didnt connect.
Ran troubleshooting (unplugged phone b4) connected phone again Kies didnt connect.
Restarted the phone in d/l mode --> wipe data/factory reset, this time the drivers were installed correctly but Kies didnt connect again.
Unplugged phone open Odin and it didnt recognize the phone either.
Tried 2 different cables switched USB ports and nothing!!
PC recognizes the phone but it wont let me see content in windows explorer.
Please help me, thanx in advance. :crying:
Pacbert
seems you need to get on another Rom
why not try odin
or root and get CWM and flash a custom Rom
Blackwolf10 said:
seems you need to get on another Rom
why not try odin
or root and get CWM and flash a custom Rom
Click to expand...
Click to collapse
I cant root the phone or how do I install another ROM. Odin doesnt recognize the phone, I plug it in and nothing happens
so I have no options how to connect to the cell phone.
Pacbert said:
I cant root the phone or how do I install another ROM. Odin doesnt recognize the phone, I plug it in and nothing happens
so I have no options how to connect to the cell phone.
Click to expand...
Click to collapse
For ODIN to recognize the device you must first go into Download Mode and you need to shutdown the device first then do this hold home+vol down+then power button)
You don't need root to use ODIN though. If you want to revert to stock see the instructions here: http://forum.xda-developers.com/showthread.php?t=1646610 it's pretty straightforward anyway so i guess you won't do something unnecessary.
As you were upgrading legitimately, take it back to vendor or Samsung and get them to sort it
SignetSphere said:
For ODIN to recognize the device you must first go into Download Mode and you need to shutdown the device first then do this hold home+vol down+then power button)
You don't need root to use ODIN though. If you want to revert to stock see the instructions here: http://forum.xda-developers.com/showthread.php?t=1646610 it's pretty straightforward anyway so i guess you won't do something unnecessary.
Click to expand...
Click to collapse
Yes I did that, I said that in my first post. I put the phone into d/l mode but Odin doesnt recognize the phone, that is my major issue here.
Neither Kies nor Odin recognizes the phone. PC installs drivers correctly and knows when its plugged in but thats about it
slaphead20 said:
As you were upgrading legitimately, take it back to vendor or Samsung and get them to sort it
Click to expand...
Click to collapse
They take a long time to respond, but yea if nobody here can give me a solution thats what Im going to do.
Nobody has a clue?
Simple test.. Tried another pc?
Sent from my Nexus 7 using xda app-developers app
realwillow said:
Simple test.. Tried another pc?
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Tried 3 different and nothing
Pacbert said:
Tried 3 different and nothing
Click to expand...
Click to collapse
you can try mobile odin then though it costs a few bucks but does a great job
Blackwolf10 said:
you can try mobile odin then though it costs a few bucks but does a great job
Click to expand...
Click to collapse
I don't think there's much chance of him being able to use mobile Odin if you read the OP
slaphead20 said:
I don't think there's much chance of him being able to use mobile Odin if you read the OP
Click to expand...
Click to collapse
Yea maybe phone has no chance at all and I probably need to replace it.
Hello Every All!
I have this device name s2 hd lte shv-e120L. Which Is Brick by my mistake. it was a rooted device and i was copying these files
"1. /system/lib/libril.so
2. /system/lib/libsec-ril.so
3. /system/lib/libsecril-client.so
4. /system/lib/libsecril-client-sap.so(4.0.4+)
5. /system/bin/drexe" unfortunately i moved the files to another folder. when the device restart it gives me a logo some thing like that. then i connect the device with pc. and run the odin 3.07 . and select the md5 file which worth about 950 mb.(which has included rom firmware every thing full package). the odin flash modem amss.bin sucessfuly but was stop at when it was flashing system .i retries many times. i change the odin version. odin 3.05 or odin 1.85 but nothing happens i change the flash package. i download the orignal firmware from sammobile. and try to flash. but i was getting some thing like xml...write faild error at the start. then i decide to flash cwm recovery backup. which i has already made before some days. the odin shows some thing like coppying files 2 minutes remaining. getting reponse 2 minutes left. etc . i stoped the flashing and then suddenly my cell was turned off.. and when ever i connect my device it shows me Qhsusb_dload. i installed the drivers. device manager shows me Qualcomm HS-USB Dloader 9008 (com3)..
Then I Take A Serach And Read Out Many Threads . at Last I Go to Vendor And Got The Live Desktop Cd Of Ubunto 12.4 . I Installed. And Download the files Brickfix 1 . Brickfix 2.1 .Pythone. Etc . I Read The Method Posted
http://forum.xda-developers.com/showthread.php?t=1914359&page=7
.i open the Qpst As Admin. Add A Port Name com 3. then i opened the sw name emmcswdownload as admin. i copy paste the files mentioned in the procedure.as i post screenshot. but when ever i click on the download i got the error like that cookie not present , mentioned in the screen shot.i need the sollution of it. i did nt have any jtag. also not able to use this service. i have usb cable s2 (bricked) .internet. pateince.
Plz Suggest me What To Do. If u dont know the situation. plz dont reply.i am really in problem. i needs every kind of help. senior members. developers. and many other freinds welcome to read my thread. still waiting for your replies,
usm125 said:
Hello Every All!
I have this device name s2 hd lte shv-e120L. Which Is Brick by my mistake. it was a rooted device and i was copying these files
"1. /system/lib/libril.so
2. /system/lib/libsec-ril.so
3. /system/lib/libsecril-client.so
4. /system/lib/libsecril-client-sap.so(4.0.4+)
5. /system/bin/drexe" unfortunately i moved the files to another folder. when the device restart it gives me a logo some thing like that. then i connect the device with pc. and run the odin 3.07 . and select the md5 file which worth about 950 mb.(which has included rom firmware every thing full package). the odin flash modem amss.bin sucessfuly but was stop at when it was flashing system .i retries many times. i change the odin version. odin 3.05 or odin 1.85 but nothing happens i change the flash package. i download the orignal firmware from sammobile. and try to flash. but i was getting some thing like xml...write faild error at the start. then i decide to flash cwm recovery backup. which i has already made before some days. the odin shows some thing like coppying files 2 minutes remaining. getting reponse 2 minutes left. etc . i stoped the flashing and then suddenly my cell was turned off.. and when ever i connect my device it shows me Qhsusb_dload. i installed the drivers. device manager shows me Qualcomm HS-USB Dloader 9008 (com3)..
Then I Take A Serach And Read Out Many Threads . at Last I Go to Vendor And Got The Live Desktop Cd Of Ubunto 12.4 . I Installed. And Download the files Brickfix 1 . Brickfix 2.1 .Pythone. Etc . I Read The Method Posted
http://forum.xda-developers.com/showthread.php?t=1914359&page=7
.i open the Qpst As Admin. Add A Port Name com 3. then i opened the sw name emmcswdownload as admin. i copy paste the files mentioned in the procedure.as i post screenshot. but when ever i click on the download i got the error like that cookie not present , mentioned in the screen shot.i need the sollution of it. i did nt have any jtag. also not able to use this service. i have usb cable s2 (bricked) .internet. pateince.
Plz Suggest me What To Do. If u dont know the situation. plz dont reply.i am really in problem. i needs every kind of help. senior members. developers. and many other freinds welcome to read my thread. still waiting for your replies,
Click to expand...
Click to collapse
Ok...first i need to know certain things...
1. Does you device boot into download mode??....if it does then it is not brick its only soft brick and can be revived....:fingers-crossed:
A device that is truly Bricked will not even turn on....it will simply not show anything on the screen...no matter what !!
So if your device boots into download mode then don't worry and don't lose hope...:good:
2. Tell me if it boots into recovery....??
if not ... then try to flash a recovery using odin....
if it does ... then first of all Wipe Data/Cache and Dalvik Cache
copy a rom on your sd card and flash it through the recovery... and then Wipe Data/Cache and Dalvik Cache again...
Let me know if anything helped ... and let me know other updates.... Hope things work for you...
Thanks
Shrewdy said:
Ok...first i need to know certain things...
1. Does you device boot into download mode??....if it does then it is not brick its only soft brick and can be revived....:fingers-crossed:
A device that is truly Bricked will not even turn on....it will simply not show anything on the screen...no matter what !!
So if your device boots into download mode then don't worry and don't lose hope...:good:
2. Tell me if it boots into recovery....??
if not ... then try to flash a recovery using odin....
if it does ... then first of all Wipe Data/Cache and Dalvik Cache
copy a rom on your sd card and flash it through the recovery... and then Wipe Data/Cache and Dalvik Cache again...
Let me know if anything helped ... and let me know other updates.... Hope things work for you...
Thanks
Click to expand...
Click to collapse
Thanks Bro For Your Reply. But My Device Is Totally Hard Bricked. it Does not Turn ON. As i Said i am getting. Qhsusb_dload Mode. that means my device is totally ****ed off.
usm125 said:
Thanks Bro For Your Reply. But My Device Is Totally Hard Bricked. it Does not Turn ON. As i Said i am getting. Qhsusb_dload Mode. that means my device is totally ****ed off.
Click to expand...
Click to collapse
I am not sure... but you can try this guide here ...
http://forum.xda-developers.com/showthread.php?t=1840030
Since it is already bricked... you can take all the chances to revive it....
And i searched on the internet and there is a lot of stuff available for Qhsusb_dload Mode you mentioned above.... take the chances ...:good:
my dear the link you send me is for those phones whose are getting into download mode and turned on. but my phone is dead. bettry is charged.but when ever i am connecting my phone to pc.it does not shows me in odin. the drivers and every thing is properly installed. i needs some one's help who is understanding about my problem. my device is hard brick. it is not going to turn On. also not going into any download mode or recovery...i know there is no way without jtag. but currently jtag is not in my range. so i want turn on it my self. there is alot of members who is eligible to solve my problem. but i think they are busy some where that's why they are not helping me. but i am still waiting ....
Motheboard replacement or JTAG.
MistahBungle said:
Motheboard replacement or JTAG.
Click to expand...
Click to collapse
i am sorry to say but there is a members who can able to fix these problems have a proof take a look here
http://forum.xda-developers.com/showthread.php?t=1914359&page=10
the member name darkspr1te is able to fix my problem and the member E.V.A Too.
1) I call bull**** on that (for the SGS2 at least).
2) If those people are fixing it for you, why are you posting in this thread ?
Bottom line is, if the phone won't boot, you ain't fixing it.
The end.
MistahBungle said:
1) I call bull**** on that (for the SGS2 at least).
2) If those people are fixing it for you, why are you posting in this thread ?
Bottom line is, if the phone won't boot, you ain't fixing it.
The end.
Click to expand...
Click to collapse
i already said in my post if the people's who dont know about my problem should not reply in my thread,
Unfortunately you don't get that option on XDA, you put a thread up, anyone can reply (unless it's a development thread, which this isn't).
My earlier diagnoses of motherboard replacement or JTAG stand.
MistahBungle said:
Unfortunately you don't get that option on XDA, you put a thread up, anyone can reply (unless it's a development thread, which this isn't).
My earlier diagnoses of motherboard replacement or JTAG stand.
Click to expand...
Click to collapse
These Things Are Not in MY Range.
Then your phone stays busted *shrugs*
MistahBungle said:
Then your phone stays busted *shrugs*
Click to expand...
Click to collapse
i needs help not a sadness..