Related
I wanted to return my rezound to stock after running ics and roms for several months now.
I relocked the phone without issue and read in many forums, once this is done, to use the factory RUU from February to return to stock.
However once relocked and back in hboot, I could only go between the bootloader and fastboot.
I have run the RUU while in fastboot usb and it recognized the phone, however I ran into the Main Ver problem.
I have further read that this is fixable via http://forum.xda-developers.com/showthread.php?t=1467099
But to do that I need the phone to boot into Android and I cannot figure out how to do that or any other way around these problems.
I am grateful for any help.
JK503 said:
I wanted to return my rezound to stock after running ics and roms for several months now.
I relocked the phone without issue and read in many forums, once this is done, to use the factory RUU from February to return to stock.
However once relocked and back in hboot, I could only go between the bootloader and fastboot.
I have run the RUU while in fastboot usb and it recognized the phone, however I ran into the Main Ver problem.
I have further read that this is fixable via http://forum.xda-developers.com/showthread.php?t=1467099
But to do that I need the phone to boot into Android and I cannot figure out how to do that or any other way around these problems.
I am grateful for any help.
Click to expand...
Click to collapse
I suggest fixing the MainVer problem by flashing this: https://dl.dropbox.com/u/30190874/Se... (1).zip rename to ph98img
I got it from Scottsroms website.
However, if you are S-on and have flashed an ICS RUU, then you can't go back to GB unless you S-off.
topgun1953 said:
I suggest fixing the MainVer problem by flashing this: https://dl.dropbox.com/u/30190874/Se... (1).zip rename to ph98img
I got it from Scottsroms website.
However, if you are S-on and have flashed an ICS RUU, then you can't go back to GB unless you S-off.
Click to expand...
Click to collapse
Alright, I had trouble with the dropbox link. I kept running into an error.
I am fine with it saying relocked. If I have a Gingerbread RUU and reset the MainVer and am on ICS firmware I cannot flash a Gingerbread RUU?
Can I rename the file ph98img.zip and flash it that way?
Edit - I reunlocked the phone. I have setmainverlow.zip. I have been reading on scottsroms that after running this and re-relocking int, I should be able to run the Gingerbread RUU.
Edit- That got me past the main ver problem. Now it says the hboot is to old. Is there something I can flash to revert to an older hboot?
JK503 said:
Alright, I had trouble with the dropbox link. I kept running into an error.
I am fine with it saying relocked. If I have a Gingerbread RUU and reset the MainVer and am on ICS firmware I cannot flash a Gingerbread RUU?
Can I rename the file ph98img.zip and flash it that way?
Edit - I reunlocked the phone. I have setmainverlow.zip. I have been reading on scottsroms that after running this and re-relocking int, I should be able to run the Gingerbread RUU.
Edit- That got me past the main ver problem. Now it says the hboot is to old. Is there something I can flash to revert to an older hboot?
Click to expand...
Click to collapse
I'll see what others have to say but I think you need to be s-off to do that.
Will someone confirm?
topgun1953 said:
I'll see what others have to say but I think you need to be s-off to do that.
Will someone confirm?
Click to expand...
Click to collapse
If you are S-On and have flashed the ICS firmware you cannot go back.
Chyrux said:
If you are S-On and have flashed the ICS firmware you cannot go back.
Click to expand...
Click to collapse
Good to know, thanks for your response.
So I have Scott's CleanROM GBE 1.7.5 on my phone. I was wandering through my phone's settings, and accidentally hit something in the update area. I do not know what I was thinking, but I know I expected it to ask me if I was sure I wanted to update. So far it has only done the first part where it prepares the phone for the update. I do not know when the other part is coming but I assume it is automatic. I was planning on updating to a rooted ICS once I felt comfortable with it (just seemed a little harder than my original flash of rooted GB). So if it would be easier to just update to ICS some way now, I would be very willing to do that. I am s-on, I believe I installed Amon Ra, but I am not sure how to check and not sure if I have an actual recovery rom or not.
I checked around and found similar problems, but nothing really like mine since my update has not gone all the way thru yet. If anyone could help, it would be greatly appreciated. THank you.
Easiest way is to relock your bootloader, run the newest ruu, unlock and flash recovery again. That way you will be set up to run any ics Rom without having to worry about flashing a patch
Sent from my ADR6425LVW using Tapatalk 2
pwned3 said:
Easiest way is to relock your bootloader, run the newest ruu, unlock and flash recovery again. That way you will be set up to run any ics Rom without having to worry about flashing a patch
Sent from my ADR6425LVW using Tapatalk 2
Click to expand...
Click to collapse
Ok just to make sure I know and don't mess anything else up. I relock (should be easy to.find a guide) . Then run the update on my phone? Then unlock thru HTC again, and flash the actual amon or CWM to my phone? And from there I will be able to flash any ICS Rom with more ease?
And thank you for the quick reply.
Edit: I searched the internet more for less-similar situations. I think all I have to do is re-lock. Download the newest RUU from Android police and put it in the root of the SD card as PH98IMG.zip (I'm assuming it should be the internal memory, but please correct me if I am wrong.) Hold volume down & power to boot into bootloader, then the phone takes it from there?
Also,nothing I have to do as far as unrooting?
malignancyy said:
Also,nothing I have to do as far as unrooting?
Click to expand...
Click to collapse
Nope just relock the bootloader
AshtonTS said:
Nope just relock the bootloader
Click to expand...
Click to collapse
Okay, thanks a lot. And I edited this into a prior post, but I just wanted to make sure:
I have to re-lock. Download the newest RUU from Android police and put it in the root of the SD card as PH98IMG.zip (I'm assuming it should be the internal memory, but please correct me if I am wrong.) Hold volume down & power to boot into bootloader, then the phone takes it from there?
malignancyy said:
Okay, thanks a lot. And I edited this into a prior post, but I just wanted to make sure:
I have to re-lock. Download the newest RUU from Android police and put it in the root of the SD card as PH98IMG.zip (I'm assuming it should be the internal memory, but please correct me if I am wrong.) Hold volume down & power to boot into bootloader, then the phone takes it from there?
Click to expand...
Click to collapse
Then you just have to press continue when it tells you to.
PS: Another way to get to the bootloader is to use adb (make sure USB debugging is enabled on your phone)
Command:
adb reboot bootloader
I find it easier than holding down buttons for a long time, but that's just my personal preference.
(Also, most custom ROMs can reboot to bootloader from within the ROM. I forget if CleanROM GBE includes the advanced power menu.)
pwned3 said:
Easiest way is to relock your bootloader, run the newest ruu, unlock and flash recovery again. That way you will be set up to run any ics Rom without having to worry about flashing a patch
Sent from my ADR6425LVW using Tapatalk 2
Click to expand...
Click to collapse
Good advise, and if he RUUs to ICS, then he should not even get asked to install the update because it will already be installed on his phone.
Also RUU twice. Just reboot into bootloader right away and install the RUU a second time. Then boot up normally and remove the zip file from the sdcard.
Thanks, you all helped a lot. I was able to get the stock rom, rooted, and running smoothly. But, once I tried to install custom roms I had problems. I decided to S-off to make it easier from here on out. After a few tries, it said I had successfully done the S-off. I tried to install Juopunutbear custom hboot, directly afterwards and it said it installed but I was stuck on the Juopunutbear screen. After this, I have not been able to get past hboot.I do not think the custom hboot actually installed. It is saying from the top:
***TAMPERED***
***LOCKED***
VIGOR PVT SHIP S-OFF RL
HBOOT-2.27.0000
RADIO-2.22.10.0801r/2.22.10.0803r
OpenDSP-v14.6.0.7708.00.0507
eMMC-boot
Aug 6 2012, 19:24:37
My external sd card needed formatting, so I just did that. And my plan is to RUU again (i guess twice), flash recovery (when clicked on currently, nothing happens), I guess root although I am not sure about this part, then try to install a custom rom.
Didn't want to make another thread just to check on this, but does this sound about right?
And as far as installing rom since I am now s-off, just go to recovery and flash it, nothing else at all to worry about?
malignancyy said:
Thanks, you all helped a lot. I was able to get the stock rom, rooted, and running smoothly. But, once I tried to install custom roms I had problems. I decided to S-off to make it easier from here on out. After a few tries, it said I had successfully done the S-off. I tried to install Juopunutbear custom hboot, directly afterwards and it said it installed but I was stuck on the Juopunutbear screen. After this, I have not been able to get past hboot.I do not think the custom hboot actually installed. It is saying from the top:
***TAMPERED***
***LOCKED***
VIGOR PVT SHIP S-OFF RL
HBOOT-2.27.0000
RADIO-2.22.10.0801r/2.22.10.0803r
OpenDSP-v14.6.0.7708.00.0507
eMMC-boot
Aug 6 2012, 19:24:37
My external sd card needed formatting, so I just did that. And my plan is to RUU again (i guess twice), flash recovery (when clicked on currently, nothing happens), I guess root although I am not sure about this part, then try to install a custom rom.
Didn't want to make another thread just to check on this, but does this sound about right?
And as far as installing rom since I am now s-off, just go to recovery and flash it, nothing else at all to worry about?
Click to expand...
Click to collapse
The jbear hboot might have failed because you are on the newest global update with 2.27 hboot, and I believe the controlbear tool still has the 2.25 hboot. (someone correct me if I'm wrong)
I think there is an unguarded 2.27 hboot somewhere, so you should flash that manually.
Sent from my NeoMax Rezound
Right now, like I said the hboot says at the top 2.27.0000
When I reboot from there, or boot it regularly it goes to a JuopunutBear, black and green writing screen.
I have tried to install this forum.xda-developers.com/showthread.php?t=1843030 ([HBOOT] HBoot 2.27 (from 4.03.605 OTA) Unlocked) from both, but cannot figure out how to do so.
edit: within JuopunutBear, wiping says "can't open" and applying update gives "failed to open loopdevice" and "failed to mount /sdcard" when I try to update.
Within the regular hboot, I get "no image" as it searches for files.
Well, I put the same file on a new sd card, and it worked on the first try, kinda.
Now it appears my phone is bricked. It will not boot at all. She barely lasted a few hours s-off before I messed it up. Any tips anyone out there can give to this sad fellow, or am I off to get a replacement?
A little more info on this. Windows tries installing QHUSB_DLOAD driver for it when plugged in, but unsuccessfully. The charging indicator does not come on either. Have tried to turn it on plugged in with battery out, and battery in both ways.
malignancyy said:
Well, I put the same file on a new sd card, and it worked on the first try, kinda.
Now it appears my phone is bricked. It will not boot at all. She barely lasted a few hours s-off before I messed it up. Any tips anyone out there can give to this sad fellow, or am I off to get a replacement?
Click to expand...
Click to collapse
Depending on what caused the brick, it may be recoverable.
Check out the unbricking thread in the dev section.
Sent from my NeoMax Rezound
Wanted to post this in the NeoMax thread, but I am currently not allowed to. I gave up on my last Rezound, and am getting a replacement here soon. I did a bunch of reading before and after I got my Rezound, and a bunch more the past few days as I wanted to get an ICS rom. Unfortunately, the one time I deferred from guides I followed (installing the JBear hboot), I killed my Rezound. I now want to stay S-on, at least until I gain some more familiarity and skill with this whole process.
What I plan on doing is once I get the Rezound, installing the OTA update, possibly having to wait for it to do so. I assume this would be the newest, .2, global update. I plan to unlock, flash recovery, then root. The rom I really want however is NeoMax. There are limited instructions on how I go about this. But from what I understand I change the filename to PH98IMG and flash it from hboot? The file name is originally, GlobalRuuPH98IMG.zip, but the thread title claims ICS De-Sensed 3.14.605.12, which I believe is two versions prior. So here I am lost. If it is in fact older, I have to flash the rom through recovery, then flash the kernel, correct? If so, do I just use the 3.14.605 that was in the NeoMax thread?
Sorry to bother you all with what i'm sure others have done many times. Like I said, I have read a lot on this, its just that I either did not understand in the least what the guides were saying, or it seemed like this situation was much different. And on a side note, if there is any other rom out there that someone would recommend that would make this easier (such as being on the latest kernel), I wouldn't be opposed to trying it. I just want one that is desensed, as it is one of my main reasons for wanting a custom rom.
malignancyy said:
Wanted to post this in the NeoMax thread, but I am currently not allowed to. I gave up on my last Rezound, and am getting a replacement here soon. I did a bunch of reading before and after I got my Rezound, and a bunch more the past few days as I wanted to get an ICS rom. Unfortunately, the one time I deferred from guides I followed (installing the JBear hboot), I killed my Rezound. I now want to stay S-on, at least until I gain some more familiarity and skill with this whole process.
What I plan on doing is once I get the Rezound, installing the OTA update, possibly having to wait for it to do so. I assume this would be the newest, .2, global update. I plan to unlock, flash recovery, then root. The rom I really want however is NeoMax. There are limited instructions on how I go about this. But from what I understand I change the filename to PH98IMG and flash it from hboot? The file name is originally, GlobalRuuPH98IMG.zip, but the thread title claims ICS De-Sensed 3.14.605.12, which I believe is two versions prior. So here I am lost. If it is in fact older, I have to flash the rom through recovery, then flash the kernel, correct? If so, do I just use the 3.14.605 that was in the NeoMax thread?
Sorry to bother you all with what i'm sure others have done many times. Like I said, I have read a lot on this, its just that I either did not understand in the least what the guides were saying, or it seemed like this situation was much different. And on a side note, if there is any other rom out there that someone would recommend that would make this easier (such as being on the latest kernel), I wouldn't be opposed to trying it. I just want one that is desensed, as it is one of my main reasons for wanting a custom rom.
Click to expand...
Click to collapse
Don't worry, you're not bothering anyone.
The people who claim to have bricked their phones when they have a boot loop and say nothing about their rom and firmware are bothering people.
Keep doing what you are currently doing and people will always be willing to help you.
Ok, so back to helping...
Of you're starting on GB, make sure you update to 3.14.605.12 before updating to the most recent one.
If you update via OTA then you don't need to worry.
Keep in mind that NeoMax is based off of the 3.14.605.12 build, so you'll have to mix n match the right way to get it to work on the latest firmware.
I believe it was you have to use the new kernel if you use the new radios and hboot.
So after installing NeoMax, flash the PH98IMG that contains the newer kernel, not the 3.14.605.12 version.
Or use fastboot to flash the kernel. (my preferred method while s-on)
Sent from my NeoMax Rezound
PS: A good way to get the required 10 posts to post in the dev section is post random stuff in the off topic thread.
wlmeng11 said:
Don't worry, you're not bothering anyone.
The people who claim to have bricked their phones when they have a boot loop and say nothing about their rom and firmware are bothering people.
Keep doing what you are currently doing and people will always be willing to help you.
Ok, so back to helping...
Of you're starting on GB, make sure you update to 3.14.605.12 before updating to the most recent one.
If you update via OTA then you don't need to worry.
Keep in mind that NeoMax is based off of the 3.14.605.12 build, so you'll have to mix n match the right way to get it to work on the latest firmware.
I believe it was you have to use the new kernel if you use the new radios and hboot.
So after installing NeoMax, flash the PH98IMG that contains the newer kernel, not the 3.14.605.12 version.
Or use fastboot to flash the kernel. (my preferred method while s-on)
Sent from my NeoMax Rezound
PS: A good way to get the required 10 posts to post in the dev section is post random stuff in the off topic thread.
Click to expand...
Click to collapse
As far as which kernel, this is what was said in the NeoMAX Q&A:
Q: "I flashed your rom and my phone gets really hot after a while. In fact, Ive noticed it on all the newer roms lately. What could be causing it and how can I attempt to fix it?"
A: "Make sure you have updated your radio to the latest available and then flash the 2nd to latest kernel. This combination has been known to have the best rom performance for all my roms and decreased heat"
SO this means I should use the 4.03.605.1? And the newest radio will automatically still be on there from the OTA update, or will I have to flash those as well? I have no experience in flashing radios so this is new ground to me.
malignancyy said:
As far as which kernel, this is what was said in the NeoMAX Q&A:
Q: "I flashed your rom and my phone gets really hot after a while. In fact, Ive noticed it on all the newer roms lately. What could be causing it and how can I attempt to fix it?"
A: "Make sure you have updated your radio to the latest available and then flash the 2nd to latest kernel. This combination has been known to have the best rom performance for all my roms and decreased heat"
SO this means I should use the 4.03.605.1? And the newest radio will automatically still be on there from the OTA update, or will I have to flash those as well? I have no experience in flashing radios so this is new ground to me.
Click to expand...
Click to collapse
That QA is outdated.
It was referring to using the 3.14.605.07 kernel as opposed to the then-most-recent 3.14.605.10
Back then those two builds were similar enough that they could mix n match without issues.
Between 3.14.605.12 and 4.03.605.1 is a lot of changes. (whole number change to represent it) Specifically, new hboot and radios. Therefore, it is incompatible with the older kernels.
When you're S-ON you can't touch the radios except through an official RUU.
Even with s-off I doubt you can flash radios from recovery (not sure on this one), and NeoMax doesn't have any radio files anyway. (nor does any rom I know for this phone)
If you haven't yet updated to 4.03.605.1 then I recommend that you stay on 3.14.605.12 until Neo updates the ROM.
If you already updated, it is still possible to run NeoMax. You just have to manually flash the new 4.03.605.1 kernel after installing the ROM.
Sent from my NeoMax Rezound
So I'm currently on Flyhalf's CM10.1 (S-ON), and I checked the recommended firmware/radios for the ROM and realized I'm outdated. It calls for Hboot 2.26 and radio 2.23.10.0123r, 2.23.10.0124r. but I'm on 2.25 and 1.22.10.0421r/1.22.10.0424r. I just updated to the latest version of the rom and I keep getting random bootlooping as well as the rom being way more unstable than the previous build I was on for about 4 months.
So, I'm trying to use Wildhorse's guide to updating firmware through RUU in hopes that it will solve my problems and it just plain isn't working. I've put the RUU in my external SD as PH98IMG, waited for my battery to charge to 90%, shut off the phone, pulled the battery, then gone into Hboot to flash it but I keep getting "No Image or Wrong Image" and it just goes back to the main Hboot screen every single time. Can anyone explain to me why this is happening even though I'm following everybody's directions exactly? I've been searching through the forums for about 2 hours now and I can't get an answer.
I'm still kind of new to HTC devices and how they work, so if anyone could help me figure this out I'd be very thankful.
BrahManty said:
So I'm currently on Flyhalf's CM10.1 (S-ON), and I checked the recommended firmware/radios for the ROM and realized I'm outdated. It calls for Hboot 2.26 and radio 2.23.10.0123r, 2.23.10.0124r. but I'm on 2.25 and 1.22.10.0421r/1.22.10.0424r. I just updated to the latest version of the rom and I keep getting random bootlooping as well as the rom being way more unstable than the previous build I was on for about 4 months.
So, I'm trying to use Wildhorse's guide to updating firmware through RUU in hopes that it will solve my problems and it just plain isn't working. I've put the RUU in my external SD as PH98IMG, waited for my battery to charge to 90%, shut off the phone, pulled the battery, then gone into Hboot to flash it but I keep getting "No Image or Wrong Image" and it just goes back to the main Hboot screen every single time. Can anyone explain to me why this is happening even though I'm following everybody's directions exactly? I've been searching through the forums for about 2 hours now and I can't get an answer.
I'm still kind of new to HTC devices and how they work, so if anyone could help me figure this out I'd be very thankful.
Click to expand...
Click to collapse
You are on a leaked firmware, the currently available RUUs are all older than that, and you can't go back when you are S-ON. You need to S-OFF then you can RUU back to 3.14.605.12 and then OTA back up to the current 4.5.605.14
acejavelin said:
You are on a leaked firmware, the currently available RUUs are all older than that, and you can't go back when you are S-ON. You need to S-OFF then you can RUU back to 3.14.605.12 and then OTA back up to the current 4.5.605.14
Click to expand...
Click to collapse
Okay, I was really hoping that wasn't the case. I hate to ask for more help, but I don't really understand how I'm supposed to get S-Off when I need to be on the stock RUU to do it, and I can't get on the stock RUU because I need to be S-Off to do so...
I hope I'm not stuck this way. Technically I'm on all the same software as I was yesterday, but now I'm getting random reboots all the time as well as bootloops that either go on for ten minutes or never end. I was on a build of CM10.1 from may with Amon Ra recovery, then tried to flash the newest TWRP that requires the new firmware (didn't realize I was on older firmware) and it bricked my phone. So I put on an older CWM recovery, tried to backup and it froze in the middle of every backup it tried to make. Put on an old TWRP, backups worked, so I flashed the newest version of CM10.1 (again not knowing I didn't have newest firmware) and that's when the bootlooping/rebooting started. I recovered to the old version of CM10.1 and the issue didn't go away, so now I'm just trying to figure out what I can do to get my phone in a usable state again.
BrahManty said:
Okay, I was really hoping that wasn't the case. I hate to ask for more help, but I don't really understand how I'm supposed to get S-Off when I need to be on the stock RUU to do it, and I can't get on the stock RUU because I need to be S-Off to do so...
I hope I'm not stuck this way. Technically I'm on all the same software as I was yesterday, but now I'm getting random reboots all the time as well as bootloops that either go on for ten minutes or never end. I was on a build of CM10.1 from may with Amon Ra recovery, then tried to flash the newest TWRP that requires the new firmware (didn't realize I was on older firmware) and it bricked my phone. So I put on an older CWM recovery, tried to backup and it froze in the middle of every backup it tried to make. Put on an old TWRP, backups worked, so I flashed the newest version of CM10.1 (again not knowing I didn't have newest firmware) and that's when the bootlooping/rebooting started. I recovered to the old version of CM10.1 and the issue didn't go away, so now I'm just trying to figure out what I can do to get my phone in a usable state again.
Click to expand...
Click to collapse
Hey, wait a sec... :laugh:
My bad, I just double checked, and with that Hboot/radio combination you are on stock ICS firmware already! Just RUU version 3.14.605.12, that should work without issues if done correctly and you should be back to pure ICS and can then allow the OTA to upgrade you in a few steps to 4.5.605.14
acejavelin said:
Hey, wait a sec... :laugh:
My bad, I just double checked, and with that Hboot/radio combination you are on stock ICS firmware already! Just RUU version 3.14.605.12, that should work without issues if done correctly and you should be back to pure ICS and can then allow the OTA to upgrade you in a few steps to 4.5.605.14
Click to expand...
Click to collapse
Oh, thank god. Hahah. I didn't remember ever flashing any leaked firmware before, so I was kind of confused there. I figured I may have done it somewhere in the unlocking/rooting process and just couldnt remember. Okay, thanks again for the help. RUU's have always confused me with the way they work. I should be stable in no time hopefully.
And now I'm having more issues... I can't use the Rom Updater because somethings wrong with my usb connection. I can plug it in and transfer files and such, but trying to use any ADB commands results in "Device not found" and the Rom Updater says it can't connect to my device either. My HTC Drivers are up to date, so I'm not sure why this is happening. Is there any way I can just get the PH98IMG.zip for 3.14.605.12 instead of having to use the RUU?
Not really sure what you are trying to run, I didn't think there was a 3.14.605.12 executable RUU, but use this page and instructions and grab the file: http://www.androidpolice.com/2012/0...cream-sandwich-ruu-for-final-ota-3-14-605-12/
Remember you will need to RELOCK the bootloader if I am not mistaken it is possible to hard brick if you don't!
Then copy to external SD card, name the file PH98IMG.zip (beware of the Windows "double zip" issue), verify MD5 on the SDcard, then reboot into hboot and go. Do it twice!!! Let it boot up and sit for about 10 minutes to calm down, then remove the PH98IMG.zip file from the SD card. Everything should be smooth sailing from there...
You should then be S-ON, completely stock. You will need to unlock again to do anything more
acejavelin said:
Not really sure what you are trying to run, I didn't think there was a 3.14.605.12 executable RUU, but use this page and instructions and grab the file: http://www.androidpolice.com/2012/0...cream-sandwich-ruu-for-final-ota-3-14-605-12/
Remember you will need to RELOCK the bootloader if I am not mistaken it is possible to hard brick if you don't!
Then copy to external SD card, name the file PH98IMG.zip (beware of the Windows "double zip" issue), verify MD5 on the SDcard, then reboot into hboot and go. Do it twice!!! Let it boot up and sit for about 10 minutes to calm down, then remove the PH98IMG.zip file from the SD card. Everything should be smooth sailing from there...
You should then be S-ON, completely stock. You will need to unlock again to do anything more
Click to expand...
Click to collapse
Strange, re-locking the bootloader was all I needed to get the RUU to update in my bootloader. No one else said to do that in any of the instructions, but I did it and immediately it started updating with the PH98IMG that I was originally trying to flash (from here: http://forum.xda-developers.com/showpost.php?p=38527788&postcount=745&nocache=1&z=1965375486761331).
I'm back to stock now, but firmware is 4.03.605.2, not 4.03.605.14. Is that going to be an issue or can I go right ahead with re-unlocking the bootloader and flashing recovery/roms?
BrahManty said:
Strange, re-locking the bootloader was all I needed to get the RUU to update in my bootloader. No one else said to do that in any of the instructions, but I did it and immediately it started updating with the PH98IMG that I was originally trying to flash (from here: http://forum.xda-developers.com/showpost.php?p=38527788&postcount=745&nocache=1&z=1965375486761331).
I'm back to stock now, but firmware is 4.03.605.2, not 4.03.605.14. Is that going to be an issue or can I go right ahead with re-unlocking the bootloader and flashing recovery/roms?
Click to expand...
Click to collapse
Well, I have some good news and bad news...
Bad news is you are now on a leaked firmware and will have to S-OFF to go up or down in versions unless a full RUU is released for the current OTA of 4.5.605.14...
Good news is you are the global leak, and you can use the JuopunutBear S-OFF exploit from http://unlimited.io/index.htm just as if you were on the original ICS release. Also, you can S-OFF and use most ROMs and recoveries as you are now on a global mode firmware.
acejavelin said:
Well, I have some good news and bad news...
Bad news is you are now on a leaked firmware and will have to S-OFF to go up or down in versions unless a full RUU is released for the current OTA of 4.5.605.14...
Good news is you are the global leak, and you can use the JuopunutBear S-OFF exploit from http://unlimited.io/index.htm just as if you were on the original ICS release. Also, you can S-OFF and use most ROMs and recoveries as you are now on a global mode firmware.
Click to expand...
Click to collapse
Lol, all right, I would have tried to get the right firmware on there but my phone got so buggy that it wouldn't even boot into the rom anymore. So I couldn't get it on the SD card and I had to make do with what I had on there. At this point, I'm just glad the phone is usable again and I might leave it stock for a while. Thank you so much for all your help, I couldn't have figured this out without you!
BrahManty said:
Lol, all right, I would have tried to get the right firmware on there but my phone got so buggy that it wouldn't even boot into the rom anymore. So I couldn't get it on the SD card and I had to make do with what I had on there. At this point, I'm just glad the phone is usable again and I might leave it stock for a while. Thank you so much for all your help, I couldn't have figured this out without you!
Click to expand...
Click to collapse
Cool, glad you got it working.
That firmware is actually pretty decent and rock solid stable, you shouldn't have any more software related issues... Plus you can root/ROM like normal from that version, the radios may be slightler lower than most recommended versions, but they should work fine. If you do decide to go the ROM route again, I would suggest going S-OFF before starting, it will just make it easier in the long run.
Hey, just wanted to ask some questions as a follow-up since this seems to be the most relevant (and active) thread to my issue:
Long story short, got a new (to me) Rezound. It was running CM10, from the forthnightly thread. New SIM card from Verizon and I was getting data, but the no mobile network found error. After reading the threads I could find on the error, went with the suggestion of a wipe and so I did. A few too many beers while reading thru the forums, and I did the wipe a bit too thoroughly. Now I have a no OS found, and instead of thinking I know what I'm doing I'd like to ask to make sure I understand this correctly.
Currently, the phone is S-OFF, with TWRP 2.5.0.0. It's saying I'm not rooted, but then again no OS to be rooted. The dump from my bootloader is as follows:
*** TAMPERED ***
*** LOCKED ***
VIGOR PVT SHIP S-OFF RL
HBOOT-2.28.0000
RADIO-2.23.10.0123r/2.23.10.0124r
OpenDSP-v14.6.0.7708.00.0507
eMMC-boot
Sep 20 2012, 17:40:22
Click to expand...
Click to collapse
After checking this thread and this one here it looks like the following applies:
* I can just run the regular RUU (executable) to load a stock image without having to revert back to S-ON first.
* I will have to re-unlock the bootloader thru htcdev after RUUing
* I'll need to reinstall TWRP
Is this right? Am I missing anything?
JoeKamel said:
Hey, just wanted to ask some questions as a follow-up since this seems to be the most relevant (and active) thread to my issue:
Long story short, got a new (to me) Rezound. It was running CM10, from the forthnightly thread. New SIM card from Verizon and I was getting data, but the no mobile network found error. After reading the threads I could find on the error, went with the suggestion of a wipe and so I did. A few too many beers while reading thru the forums, and I did the wipe a bit too thoroughly. Now I have a no OS found, and instead of thinking I know what I'm doing I'd like to ask to make sure I understand this correctly.
Currently, the phone is S-OFF, with TWRP 2.5.0.0. It's saying I'm not rooted, but then again no OS to be rooted. The dump from my bootloader is as follows:
After checking this thread and this one here it looks like the following applies:
* I can just run the regular RUU (executable) to load a stock image without having to revert back to S-ON first.
* I will have to re-unlock the bootloader thru htcdev after RUUing
* I'll need to reinstall TWRP
Is this right? Am I missing anything?
Click to expand...
Click to collapse
You should be able to just boot into twrp and flash a rom
Sent from my ADR6425LVW using xda premium
izzaeroth said:
You should be able to just boot into twrp and flash a rom
Click to expand...
Click to collapse
Okay, that's good to know. For now though, if I just wanted to get my phone working, make sure there's not a SIM issue and such I could go back to a stock image without worrying? I just would rather do a lot more reading and make sure I understand what I'm doing before I try to put a rom on and screw things up further.
JoeKamel said:
Okay, that's good to know. For now though, if I just wanted to get my phone working, make sure there's not a SIM issue and such I could go back to a stock image without worrying? I just would rather do a lot more reading and make sure I understand what I'm doing before I try to put a rom on and screw things up further.
Click to expand...
Click to collapse
No doubt its good to be cautious when you are s-off. If you are just wanting plain jane stock then you could just flash a ruu from boot loader.
Sent from my ADR6425LVW using xda premium
izzaeroth said:
No doubt its good to be cautious when you are s-off. If you are just wanting plain jane stock then you could just flash a ruu from boot loader.
Click to expand...
Click to collapse
Okay, so if I go with the image here: http://forum.xda-developers.com/showpost.php?p=38527788&postcount=745&nocache=1&z=1965375486761331
Would I still need to relock the bootloader since I'm S-OFF or can I just flash that from TWRP and go from there?
JoeKamel said:
Okay, so if I go with the image here: http://forum.xda-developers.com/showpost.php?p=38527788&postcount=745&nocache=1&z=1965375486761331
Would I still need to relock the bootloader since I'm S-OFF or can I just flash that from TWRP and go from there?
Click to expand...
Click to collapse
Honestly I don't remember if you would have to relock to flash that in boot loader sine you are s-off, but I do know it won't flash from recovery
Sent from my ADR6425LVW using xda premium
izzaeroth said:
Honestly I don't remember if you would have to relock to flash that in boot loader sine you are s-off, but I do know it won't flash from recovery
Click to expand...
Click to collapse
Recovery as in HBoot or TWRP? Because I still have TWRP. I can get the windows executable RUU for ICS if need be.
JoeKamel said:
Recovery as in HBoot or TWRP? Because I still have TWRP. I can get the windows executable RUU for ICS if need be.
Click to expand...
Click to collapse
Recovery = twrp
Sent from my ADR6425LVW using xda premium
izzaeroth said:
Honestly I don't remember if you would have to relock to flash that in boot loader sine you are s-off, but I do know it won't flash from recovery
Sent from my ADR6425LVW using xda premium
Click to expand...
Click to collapse
S-off is S-off... installing a RUU wont change that, it may set you back to 'Locked", but you are S-off so it doesn't matter, you can stay locked&s-off and its no different than unlocked/S-off.
If you are going back to stock and are S-off I would use the Global Mode Leak (4.3.605.2) available on AndroidPolice and flash in Hboot... rename file to PH98IMG.zip and place in root of SD card (how it gets there is a irrelevant) then reboot into Hboot, confirm and wait.
Sent from my HTC Aria (Liberty) running CM 7.2 using xda app-developers app
Hi guys.
I was trying to do one of two things. Either get to stock ICS with the RUU or get to an older stock version so that my phone would update itself.
I ran the ICS RUU and ran into an issue. Im on Hboot 2.28 Radio 2.23.10.0123r/2.23.10.0124r
I am S-On and relocked to get run the RUU.
I got an error as it said the Hboot version is older. Now I am stuck on the Bootloader with TAMPERED, RELOCKED, and Security Warning.
I should have known that I potentially had a leaked Hboot version but it was so long ago I forgot.
What can I do? Iv been googling and searching threads without much luck. Do I have to S-off? Can I S-off from this position? The other issue I keep running into is dead file links.
brownsfan said:
Hi guys.
I was trying to do one of two things. Either get to stock ICS with the RUU or get to an older stock version so that my phone would update itself.
I ran the ICS RUU and ran into an issue. Im on Hboot 2.28 Radio 2.23.10.0123r/2.23.10.0124r
I am S-On and relocked to get run the RUU.
I got an error as it said the Hboot version is older. Now I am stuck on the Bootloader with TAMPERED, RELOCKED, and Security Warning.
I should have known that I potentially had a leaked Hboot version but it was so long ago I forgot.
What can I do? Iv been googling and searching threads without much luck. Do I have to S-off? Can I S-off from this position? The other issue I keep running into is dead file links.
Click to expand...
Click to collapse
So I think I found out what I did. 2.28 is the Global version. I must of rooted that version and flashed roms. I wanted to unroot and get back to stock software version.
Where should I go from here? Is there an RUU for the ICS Global? I can not seem to find one.
Have you tried unlocking the bootloader again?
Edit: I searched for a long time (a few days ago) but couldn't find any information on S-Off, not going back to stock for people on the latest OTA. I'm not the best person to give advice, but if you're on the current OTA, I don't think you can use the RUU.exe.
Also, you can't downgrade if you're S-On - only upgrade..
Sent from my ADR6425LVW using xda app-developers app
Thingula said:
Have you tried unlocking the bootloader again?
Edit: I searched for a long time (a few days ago) but couldn't find any information on S-Off, not going back to stock for people on the latest OTA. I'm not the best person to give advice, but if you're on the current OTA, I don't think you can use the RUU.exe.
Also, you can't downgrade if you're S-On - only upgrade..
Sent from my ADR6425LVW using xda app-developers app
Click to expand...
Click to collapse
Yes I can unlock again and that does get me unstock from the boot screen but still cant get where I want. Hmm.
I wonder if you can fastboot-flash the older kernels, using a computer, then flash the old stock ROM, lock the bootloader, then run an RUU.. Can anyone confirm this? Sounds too simple to work on an HTC phone.
Edit: No, of course that doesn't work. Sorry, I can't really offer any more help.. I'll have to just hope that someone more knowledgeable can take over.
Sent from my ADR6425LVW using xda app-developers app
Be prepared, I get rather long winded.
If you were on the most current 4.05.605.14 with S-on which based on what you list as the radios and hboot is what it appears you were on, then you are in a difficult spot. The really bad news is the only RUU you would be able to use is the 4.05.605.14 and no one has admitted to being able to get ahold of. The most current one available is 3.14.605.12 but that is useless to you. You would have to S-off to go back to stock but would have to have a working rom to do it. It's not impossible but it aint easy. I just had to do it about a month ago when I was trying to S-off my replacement Rezound. It came with the most current stock ROM and I didn't bother reading up on the current ControlBear method. In the past, you had to have a rooted rom in order to S-off. So of course, I unlocked the bootloader, flashed AmonRa 3.15 and then used superuser to root it and then went about trying to S-off. I couldn't find my previous windows based versions of ControlBear so I went about making a live cd ubunto disk and trying to S-off. It wouldn't work. Then I read the unlimited.io site instructions and found that the current version needs the unrooted stock rom to succeed. I really never paid attention to unrooting before because if I had to do it, I could always just run the factory wipe and root would be gone but not this time. It kept showing that I was rooted. So I tried wiping data, cache, dalvik cache, and after that didn't work, I wiped the system. Very bad move on my part. Now I couldn't get past the bootloader. I thought I was done for because I knew with S-on, there was no going back and the global rom RUU was still not available.
After trying all kinds of things I ended up
1. downloading the 4.05.605.14 stock rooted rom listed HERE (Thanks MicroMod777) in the Rezound Development section.
2. Then downloaded the current firmware.zip from HERE (Thanks Flyhalf205) and then extracted the recovery.img along with the hboot .nb0 file from it.
3. I then created 2 separate custom ph98img.zip for each so I could always reinstall the stock hboot and the stock recovery.img.
4. I extracted the boot.img from the rooted rom and flashed that first. I don't remember if I did it via adb in fastboot usb or with another ph98img.zip and then
5. I made sure that my bootloader was unlocked and then installed AmonRa as the recovery
6. Then used AmonRa to flash the stock rooted zip file. I then wiped the cache 3 times and the dalkvik cache 3 times.
I let the phone reboot and I was back to a working phone.!!! Then I found out that it was rooted with SuperSu which gives you the option of doing a full permanent unroot which I did. I then put that ph98img that I had made that had the stock recovery.img on it and flashed that in the bootloader. After rebooting I now had a fully stock phone and proceeded to do the S-off. I left the bootloader unlocked as directed by the unlimited.io site. I had limited experience with ubunto but found THIS PAGE that helped walk me through it. I followed it exactly and ended up with an S-off phone. One thing that wasn't clear to me was how to open a terminal in ubunto but I figured that out after trial and error. IIRC, I clicked on the home tab on the left and then in the search box, typed terminal. The first icon that was shown was a terminal emulator and I used that for the commands.
Now I still wasn't finished. I ended up relocking the bootloader but didn't like the relocked and tampered flags that were showing. So I ended up running the most recent RUU (3.14.605.12 found HERE and I now had a ***LOCKED*** bootloader and then let the phone reboot. After it rebooted, I hit the home key and bypassed the setup. I then got into settings and then into software update and let it update. It did a small update and then had to repeat the reboot, bypass setup, and software update. This time it did the global update. I let it reboot but this time, I ran the setup. Once I was up and running, I again went into bootloader and reinstalled AmonRa and used the 3.16 version and made sure to do a nandroid before doing anything further. After that, I got ahold of SuperSu 1.51 and flashed that in the AmonRa recovery. I now had a ***LOCKED*** stock rooted Rezound and several nandroid backups of both fully stock and rooted. Which turned out to be a great idea because not even 3 weeks later after this, the phone started malfunctioning (power button) and a problem with the camera so it got replaced and I had to put it back fully stock. I was already setup for this. I unrooted, put the stock recovery back on, and made it S-on. When the replacement came, I immediately unlocked it, did the S-off (only took one try), relocked, ruu'd back to 3.14.605.12, updated to global rom, flashed AmonRa, and restored with my most recent rooted nandroid. and I am back up and running a whole lot sooner...
I hope this helps.
Very much so! Thank you. If I could hit the thanks button 10x I would.
Im sure im not the only only to have the Hboot 2.28 issue.
hey man you still around ? i need some help with a situation like this
dust906 said:
hey man you still around ? i need some help with a situation like this
Click to expand...
Click to collapse
I replied to you in your thread.
S-On Locked stock !
mikeyk101 said:
Be prepared, I get rather long winded.
If you were on the most current 4.05.605.14 with S-on which based on what you list as the radios and hboot is what it appears you were on, then you are in a difficult spot. The really bad news is the only RUU you would be able to use is the 4.05.605.14 and no one has admitted to being able to get ahold of. The most current one available is 3.14.605.12 but that is useless to you. You would have to S-off to go back to stock but would have to have a working rom to do it. It's not impossible but it aint easy. I just had to do it about a month ago when I was trying to S-off my replacement Rezound. It came with the most current stock ROM and I didn't bother reading up on the current ControlBear method. In the past, you had to have a rooted rom in order to S-off. So of course, I unlocked the bootloader, flashed AmonRa 3.15 and then used superuser to root it and then went about trying to S-off. I couldn't find my previous windows based versions of ControlBear so I went about making a live cd ubunto disk and trying to S-off. It wouldn't work. Then I read the unlimited.io site instructions and found that the current version needs the unrooted stock rom to succeed. I really never paid attention to unrooting before because if I had to do it, I could always just run the factory wipe and root would be gone but not this time. It kept showing that I was rooted. So I tried wiping data, cache, dalvik cache, and after that didn't work, I wiped the system. Very bad move on my part. Now I couldn't get past the bootloader. I thought I was done for because I knew with S-on, there was no going back and the global rom RUU was still not available.
After trying all kinds of things I ended up
1. downloading the 4.05.605.14 stock rooted rom listed HERE (Thanks MicroMod777) in the Rezound Development section.
2. Then downloaded the current firmware.zip from HERE (Thanks Flyhalf205) and then extracted the recovery.img along with the hboot .nb0 file from it.
3. I then created 2 separate custom ph98img.zip for each so I could always reinstall the stock hboot and the stock recovery.img.
4. I extracted the boot.img from the rooted rom and flashed that first. I don't remember if I did it via adb in fastboot usb or with another ph98img.zip and then
5. I made sure that my bootloader was unlocked and then installed AmonRa as the recovery
6. Then used AmonRa to flash the stock rooted zip file. I then wiped the cache 3 times and the dalkvik cache 3 times.
I let the phone reboot and I was back to a working phone.!!! Then I found out that it was rooted with SuperSu which gives you the option of doing a full permanent unroot which I did. I then put that ph98img that I had made that had the stock recovery.img on it and flashed that in the bootloader. After rebooting I now had a fully stock phone and proceeded to do the S-off. I left the bootloader unlocked as directed by the unlimited.io site. I had limited experience with ubunto but found THIS PAGE that helped walk me through it. I followed it exactly and ended up with an S-off phone. One thing that wasn't clear to me was how to open a terminal in ubunto but I figured that out after trial and error. IIRC, I clicked on the home tab on the left and then in the search box, typed terminal. The first icon that was shown was a terminal emulator and I used that for the commands.
Now I still wasn't finished. I ended up relocking the bootloader but didn't like the relocked and tampered flags that were showing. So I ended up running the most recent RUU (3.14.605.12 found HERE and I now had a ***LOCKED*** bootloader and then let the phone reboot. After it rebooted, I hit the home key and bypassed the setup. I then got into settings and then into software update and let it update. It did a small update and then had to repeat the reboot, bypass setup, and software update. This time it did the global update. I let it reboot but this time, I ran the setup. Once I was up and running, I again went into bootloader and reinstalled AmonRa and used the 3.16 version and made sure to do a nandroid before doing anything further. After that, I got ahold of SuperSu 1.51 and flashed that in the AmonRa recovery. I now had a ***LOCKED*** stock rooted Rezound and several nandroid backups of both fully stock and rooted. Which turned out to be a great idea because not even 3 weeks later after this, the phone started malfunctioning (power button) and a problem with the camera so it got replaced and I had to put it back fully stock. I was already setup for this. I unrooted, put the stock recovery back on, and made it S-on. When the replacement came, I immediately unlocked it, did the S-off (only took one try), relocked, ruu'd back to 3.14.605.12, updated to global rom, flashed AmonRa, and restored with my most recent rooted nandroid. and I am back up and running a whole lot sooner...
I hope this helps.
Click to expand...
Click to collapse
This guide was FREAKING AWESOME. It led me to finally after 2 years go S-Off (wire trick) to do RUU, etc. Have to return phone and have already got replacement. Crossed my fingers and everything looks stock stock stock !
So, I have a dilemma. I am currently S-ON running TACHYON 1.2 (Android 4.3)
HBOOT 2.28.0000
Radio 2.23.10.0123/4
I updated the hboot and radio while S-ON. Now, I've decided I'd like to go S-OFF. According to JuopunutBear I need to be on a stock RUU for their S-OFF to work. I tried running the newest ICS RUU a few weeks ago and found that it would just error out when it was checking the file because the radios and hboot on the phone were newer than the ones on the RUU. Can I step backwards in HBOOT versions whlie S-ON or have I kind of screwed myself? Or is there a better option I haven't thought about?
Thanks
Just install a stock Rom to run s-off program. You are on a stock hboot, so no problem there.
Sent from my DNA using my mind.
Uzephi said:
Just install a stock Rom to run s-off program. You are on a stock hboot, so no problem there.
Sent from my DNA using my mind.
Click to expand...
Click to collapse
It's a stock hboot, yes. But the RUU won't run because it is an older version hboot.
You need s-off to downgrade. Just install a stock based Rom that is rooted and run s-off procedure. You will have no issues. After s-off if you want, you can ruu
Sent from my DNA using my mind.
Step 1 from Unlimited: Verify - You are on Stock RUU (not FreshROM, Stock Rooted, HarmonyROM - none of these will work!)
They say not to be rooted or anything. What difference does it make?
Also, what do you mean by "stock rom"? Is there a stock rom I can install that is not an RUU? (maybe that's a dumb question but I don't know lol)
jeff925 said:
Step 1 from Unlimited: Verify - You are on Stock RUU (not FreshROM, Stock Rooted, HarmonyROM - none of these will work!)
They say not to be rooted or anything. What difference does it make?
Also, what do you mean by "stock rom"? Is there a stock rom I can install that is not an RUU? (maybe that's a dumb question but I don't know lol)
Click to expand...
Click to collapse
A stock rooted RUU would work. I was in your predicament once. First, do a nandroid backup then use this guide it'll get you to s-off. If you want to downgrade, then use this guide to accomplish this.
Thanks guys for the help. Installed the rom listed in the guide and it worked great. S-OFF now!! (Took me long enough...I've had the phone for 2 years!)
It installed JuopunutBear's hboot but whatever. I'd probably rather stick with a stock hboot but I can do that later.
Restored my nandroid backup and I'm back up and running like I never left.
Just flash this ROM and boot image, and you should be able to S-OFF, I can't remember if stock recovery is needed but that can be flashed separately as well if needed, but I don't think it is.
http://forum.xda-developers.com/showthread.php?t=2260154
So, All was well until I decided to flash the stock hboot back to the phone. I put the file on the sd card and renamed it ph98img.zip and flashed it in fastboot. It said it was successful and that I was running hboot 2.28 and radio 2.23.10.0123/4. Then I rebooted and it hung up at the white screen with green htc logo. I pulled the battery and rebooted holding the power and volume buttons. It booted to fastboot so I tried a few things. I tried flashing a recovery but it said that remote was not allowed and failed. Then I tried opening the recovery I already had on the phone from fastboot and it gave me the software download icon. Nothing happened so I pulled the battery and tried to boot back to fastboot. This time it wouldn't even get to fastboot. The white screen with HTC logo comes up and then the screen goes blank. Then the software download icon comes up and then shortly there after a red triangle with an exclamation point takes its place.
That went downhill fast! Any suggestions?
EDIT: Pulling the SD card allows me to get back into fastboot! But I'm still not sure what to do. Is it because my bootloader is locked?
jeff925 said:
So, All was well until I decided to flash the stock hboot back to the phone. I put the file on the sd card and renamed it ph98img.zip and flashed it in fastboot. It said it was successful and that I was running hboot 2.28 and radio 2.23.10.0123/4. Then I rebooted and it hung up at the white screen with green htc logo. I pulled the battery and rebooted holding the power and volume buttons. It booted to fastboot so I tried a few things. I tried flashing a recovery but it said that remote was not allowed and failed. Then I tried opening the recovery I already had on the phone from fastboot and it gave me the software download icon. Nothing happened so I pulled the battery and tried to boot back to fastboot. This time it wouldn't even get to fastboot. The white screen with HTC logo comes up and then the screen goes blank. Then the software download icon comes up and then shortly there after a red triangle with an exclamation point takes its place.
That went downhill fast! Any suggestions?
EDIT: Pulling the SD card allows me to get back into fastboot! But I'm still not sure what to do. Is it because my bootloader is locked?
Click to expand...
Click to collapse
In fastboot does it say s-off? Try manually flashing the boot.img by extracting it. If you haven't setup enviroment variable for fastboot put the boot.img in the same directory as fastboot.exe and use command prompt by typing
Code:
cd C:\Android\platform-tools (or wherever it is for you)
Then type
Code:
fastboot flash boot boot.img
I was able to put an RUU on another sd card and flash that. So now I'm on ICS 4.03.605.2 and running. But I still haven't solved my recovery problems.
According to this thread: androidforums.com/rezound-all-things-root/550408-s-off-guide-info-return-stock.html
I can either use juopunutbear's hboot (which I just flashed over the top of) to flash a new recovery or I can compile a recovery in a ph98img file (which I don't know how to do or want to do).
My question is: What happens if I unlock my bootloader while S-OFF? (Yes, it says s-off on the bootloader screen.) Will that solve my problem or do I have to go back to juopunutbear's hboot?
jeff925 said:
I was able to put an RUU on another sd card and flash that. So now I'm on ICS 4.03.605.2 and running. But I still haven't solved my recovery problems.
According to this thread: androidforums.com/rezound-all-things-root/550408-s-off-guide-info-return-stock.html
I can either use juopunutbear's hboot (which I just flashed over the top of) to flash a new recovery or I can compile a recovery in a ph98img file (which I don't know how to do or want to do).
My question is: What happens if I unlock my bootloader while S-OFF? (Yes, it says s-off on the bootloader screen.) Will that solve my problem or do I have to go back to juopunutbear's hboot?
Click to expand...
Click to collapse
You can unlock when S-OFF, but there is no reason to, you can get a PH98img.zip of CWM here: http://forum.xda-developers.com/showthread.php?t=1914215 or TWRP here: http://forum.xda-developers.com/showthread.php?t=1902381 and just copy it to your sd card (remember to name it exactly PH98IMG.zip, beware the Windoze "double zip" issue) then pop it in the phone, boot into Hboot with the USB disconnected and it should recognize it and flash either CWM or TWRP. from there you can flash ANYTHING you want, being S-OFF with custom recovery allows you to flash anything, no fastboot commands required.
Also, since you are S-OFF, your Hboot is mostly irrelevant, but should be the matching version to your radios... an engineered hboot (like Juopunutbears) would allow fastboot commands well locked, but fastboot isn't generally needed once S-OFF has been obtained...
Try this. no wire even, works great.
http://forum.xda-developers.com/showthread.php?p=48911002#post48911002
i am on hboot 2.25 though. im thinking of updating my hboot still researching how exactly.
4218kris said:
Try this. no wire even, works great.
http://forum.xda-developers.com/showthread.php?p=48911002#post48911002
i am on hboot 2.25 though. im thinking of updating my hboot still researching how exactly.
Click to expand...
Click to collapse
i can help with that....its pretty easy if your already s-off
---------- Post added at 03:26 AM ---------- Previous post was at 03:22 AM ----------
jeff925 said:
I was able to put an RUU on another sd card and flash that. So now I'm on ICS 4.03.605.2 and running. But I still haven't solved my recovery problems.
According to this thread: androidforums.com/rezound-all-things-root/550408-s-off-guide-info-return-stock.html
I can either use juopunutbear's hboot (which I just flashed over the top of) to flash a new recovery or I can compile a recovery in a ph98img file (which I don't know how to do or want to do).
My question is: What happens if I unlock my bootloader while S-OFF? (Yes, it says s-off on the bootloader screen.) Will that solve my problem or do I have to go back to juopunutbear's hboot?
Click to expand...
Click to collapse
and what recovery problems are you having....flashing an hboot will not give you a recovery...and an ruu is an exe file not a ph98img file...those are OTA's.....if you need pure stock i can easily help you obtain it....i just need to know what exactly your trying to achieve
REV3NT3CH said:
i can help with that....its pretty easy if your already s-off
---------- Post added at 03:26 AM ---------- Previous post was at 03:22 AM ----------
Click to expand...
Click to collapse
i believe i can flash hboot with a ph98img yea? can you link me to the best/newest 2.28 i think.
4218kris said:
i believe i can flash hboot with a ph98img yea? can you link me to the best/newest 2.28 i think.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=40767819&postcount=33
4218kris said:
i believe i can flash hboot with a ph98img yea? can you link me to the best/newest 2.28 i think.
Click to expand...
Click to collapse
that one or the this 2nd ph98img in my downgrade/upgrade guide work as well...that one is just radios and hboot....doesnt come with stock <3e> recovery
REV3NT3CH said:
if you need pure stock i can easily help you obtain it....i just need to know what exactly your trying to achieve
Click to expand...
Click to collapse
Hey REV3NT3CH,
So, thanks to the help of so many in these parts, including you, I now think I'm S-Off and I'm very interested in bringing my phone up to the latest, completely stock OTA ROM. Can you help me with that?
Thanks!
cheers,
john
jrredho said:
Hey REV3NT3CH,
So, thanks to the help of so many in these parts, including you, I now think I'm S-Off and I'm very interested in bringing my phone up to the latest, completely stock OTA ROM. Can you help me with that?
Thanks!
cheers,
john
Click to expand...
Click to collapse
when you boot into your bootloader...does your hboot now say S-OFF....if so i can give you everything you need and what id suggest doing just prior to doing it
REV3NT3CH said:
when you boot into your bootloader...does your hboot now say S-OFF..
Click to expand...
Click to collapse
Yes it does.
REV3NT3CH said:
.if so i can give you everything you need and what id suggest doing just prior to doing it
Click to expand...
Click to collapse
That would be fantastic!
Thanks,
John