Hi All,
I have a Samsung GT-I9100 phone which in it's current state, no matter what button is pushed or combination is pushed together will show nothing.
Situation of death:
6.30am - on charge, working fine - Take off charge put in pocket
6.50am - take out of pocket, phone sitting on the Galaxy loading screen. Attempt turning phone off then on and gets to same point and sits there.
7.30am - pull battery off, leave for an hour
8.30am - Put battery in, same result. Find post here which recommends clear data/factory reset. Put phone into Recovery, select Clear data, reboot phone, same situation. Put phone back into recovery, select factory reset. Starts clearing, sits on this screen for about 15 min before screen turns off. leave for 10 min, nothing happened so pushed power button and nothing happened, attempted recovery mode and download mode button combination - still nothing. Removed battery for 30 min, back in and same thing.
Now stuck with my phone which will do absolutely nothing. Any suggestions would be much appreciated. From what I read a USB Jig may be appropriate so will look into a bit of shopping soon.
What ROM were you on?
Don't say 4.0.4.
Sent from the little guy
gastonw said:
What ROM were you on?
Don't say 4.0.4.
Sent from the little guy
Click to expand...
Click to collapse
Ok, I won't say it....
Instead I will say 4.1.2 I believe. I was running the latest that had been provided to me via Kies (not been using a custom rom for a long time)
Jig more than likely won't work (0.0000000000001% chance of working), but try it any way. Service centre.
MistahBungle said:
Jig more than likely won't work (0.0000000000001% chance of working), but try it any way. Service centre.
Click to expand...
Click to collapse
Took it to where I brought it, and they told me $100 min for repairs which isn't fun but I guess it's that point
Yep unfortunately that's how these things work. Look, if you can get a jig, try it. You may be one of those lucky people. But at least now you know what you're up for.
Well, thanks for the replies, sent it in and been told Mobo problems, and will cost more to replace than to buy a new phone... YAY....
Related
Hi everyone
My SGS 2 won't start anymore
I charged my phone, then went somewhere, used the phone, put it back in my pocket and the next time i looked at it it was shut down and i couldn't turn it on anymore, nothing happens at all.
theres no problem with the battery (it works on another SGS 2)
I rooted my phone and put lightning rom 1.2 on it. i had no problem rooting the phone and its the first rom since stockrom.
What should I do?
So you mean your phone won't boot anymore? There is no Samsung logo or anything?
Sent from my GT-I9100 using XDA App
no logo, no vibration, just black
tried normal startup as well as "vol down, home, power"
Recovery vol up + home + pwr release at splash screen .
You can either try the usb recovery jig though this poster says it does not work but in my view worth a try.
http://forum.xda-developers.com/showthread.php?t=1206967
Or take your chance and return the phone under warranty .
jje
Did you try removing battery, replacing and then turning on. I had the same issue yesterday and this worked for me.
Sent from my GT-I9100 using XDA Premium App
Samsung GS2 - System Crashed black screen
+1 Here. I got the same thing
I’m really newbie, first time play on Android phone and got crash
However, below are what I did in chronological order
1) I did and success
http://www.inspiredgeek.com/2011/04...ng-odin-and-superoneclick-step-by-step-guide/
2) Did & Success
http://forum.xda-developers.com/showthread.php?t=1154252
3) Did & fail
http://forum.xda-developers.com/showthread.php?t=892297
4) Outcome
It restarted, and keep restarting at Samsung start-up flash screen repeatly, can not load into mobile home screen.
I bought to Malaysia Samsung Service Center. They mention can try to flash my phone but not guaranteed. Worst still, Result:- black out, can’t start the phone even pressing power button.
Thanks, appreciate that
ps: I bought from Bangkok, is Malaysia version different? Btw, I did try to do the hard reset but same. (Vol Up + Home + Power button, then Wipe Data/ Factory Reset)
I screen capture baseband version is DXKF1, Build number is Gingerbread.DXKF4
Thanks alot man. Truly appreciate if any alternative solution or suggestion?
Having the exact same problem,
Charged phone
Listened to some music for 30 minutes
put the phone away on the table
Two hours later I noticed the phone had shut down.
Trying to boot it nothing.
Nothing when put in wall socket charger.
Nothing when connected to USB.
Vol Up + Home + Power button does nothing.
running Lightning rom 1.2 or 1.3
Phone is 2.5months old.
You may have your last try - USB jig
Same problem here, shut down the phone to put a new microsd and when i try to start it only a black screen, no samsung logo, no vibrate, no nothing....
I try to remove sim and microsd and no result, changed battery, no result, battery works in another SGS2....
Any solution?
EDIT: WORKS AGIAN!!!! i leave it alone without battery around 30 mins then put battery and working again...
my phone won't turn on. I set it down around 26% battery and went to check it about 30 min later. BLACK. plugged it in. battery break still nothing... no vibrate no lights nothing!
im leaving battery out for the night and will try it back in in the morning but im doubtful! my life sucks.
tylerlaczko said:
my phone won't turn on. I set it down around 26% battery and went to check it about 30 min later. BLACK. plugged it in. battery break still nothing... no vibrate no lights nothing!
im leaving battery out for the night and will try it back in in the morning but im doubtful! my life sucks.
Click to expand...
Click to collapse
Tried many things and not working. Sending it in for warranty. At least they wont know its hacked until they fix it. Maybe they wont charge me...
tylerlaczko said:
Tried many things and not working. Sending it in for warranty. At least they wont know its hacked until they fix it. Maybe they wont charge me...
Click to expand...
Click to collapse
So what happened? Did they work out that it was hacked and were you charged?
Hi guys,
three days ago I installed Darkyrom HD on my mates Galaxy S2, everything went smooth. But 10 minutes ago he called and said that the phone woudn't turn on!
He says he can't get response out of it. No recovery or hard reset with nor without battery in.
Don't hope it's perma bricked and it seems weird that it suddenly wont turn on.
Any ideas/help?
Thanks a lot.
At the same time press volume up + home button + power on to enter CWM.
Is his battery charged?
Prozel said:
Hi guys,
three days ago I installed Darkyrom HD on my mates Galaxy S2, everything went smooth. But 10 minutes ago he called and said that the phone woudn't turn on!
He says he can't get response out of it. No recovery or hard reset with nor without battery in.
Don't hope it's perma bricked and it seems weird that it suddenly wont turn on.
Any ideas/help?
Thanks a lot.
Click to expand...
Click to collapse
Does it get a response if holding down the power button for 8-10 sec? This will essentially reboot the phone regardless of what state it is in. If your buddy's been hit with the "sleep of death", this will boot the phone. Though I think this is a low probability if he tried pulling battery and putting it back.
Does it get a response if plugging it into the AC adapter? On the off chance the battery is completely dead. I'd like to think he tried this, though.
Has he tried another battery? Could be the battery lost the ability to hold a charge. Not common, but not unheard of either.
Doesn't seem to help. But I've told to let it charge the night and try again.
Any particular this happens? Seems random that it suddenly wont turn on.
Prozel said:
Doesn't seem to help. But I've told to let it charge the night and try again.
Any particular this happens? Seems random that it suddenly wont turn on.
Click to expand...
Click to collapse
Any particular reason? Sure. Most often, because the user installs something or flashes something they are not supposed to, to their phone. Or dropped it in water.
ctomgee said:
Any particular reason? Sure. Most often, because the user installs something or flashes something they are not supposed to, to their phone. Or dropped it in water.
Click to expand...
Click to collapse
This is what I did:
- Flashede an insecure kernel
- Rootede and installed busybox
- Downloaded Darky's OTA
- Downloaded og installed his kernel (SuperCore)
- Bootede in CWM and installed his ROM
Prozel said:
This is what I did:
- Flashede an insecure kernel
- Rootede and installed busybox
- Downloaded Darky's OTA
- Downloaded og installed his kernel (SuperCore)
- Bootede in CWM and installed his ROM
Click to expand...
Click to collapse
I wasn't trying to say YOU installed or flashed something. Maybe he did. Can I assume the phone was working when you gave it back to him? And that it was working fine for the three days after? Or was the phone in YOUR possession until he called you today?
I haven't had phone since i installed it. But I honestly don't think i he flashed anything.
He went out to jog - phone worked (listening to music)
He came home and placed the phone on the table - Phone worked
He did some exercises and when he came back - phone all black, can't get any response
Prozel said:
I haven't had phone since i installed it. But I honestly don't think i he flashed anything.
He went out to jog - phone worked (listening to music)
He came home and placed the phone on the table - Phone worked
He did some exercises and when he came back - phone all black, can't get any response
Click to expand...
Click to collapse
You said he tried a battery pull? And no response after replacing battery?
Sure his battery is just not dead, bit odd if it had been working and suddenly this happens.
Most cases an app or something can cause the phone to restart, or freezes, usually a hard reset solves this by holding down the power button for about 10 seconds.
Or entering recovery mode, or download mode just to ensure they are working.
Make sure he can charge the battery.
If all fails you may need to try a jig.
Sent from my GT-I9100 using Tapatalk
No response afer he pulled the battery.
Prozel said:
No response afer he pulled the battery.
Click to expand...
Click to collapse
Hmm. Try a different battery. If that doesn't work, warranty time.
Sent from my GT-I9100 using XDA App
We are trying to get another battery. In the meantime I've ordered a USB Jig that hopefully will turn the beast on!
Prozel said:
We are trying to get another battery. In the meantime I've ordered a USB Jig that hopefully will turn the beast on!
Click to expand...
Click to collapse
If not you will need to reflash to stock rom as warranty void with root or custom rom ..
JTag may be your next step .
jje
try to get into download mode (vol. down, home and standby button) then you can flash a firmware
Sent from my GT-I9100 using XDA App
Judaas said:
try to get into download mode (vol. down, home and standby button) then you can flash a firmware
Sent from my GT-I9100 using XDA App
Click to expand...
Click to collapse
READ the post please before answering .
We are trying to get another battery. In the meantime I've ordered a USB Jig that hopefully will turn the beast on!
jje
It wasn't the battery. But we've found someone that can repair it for 25 pounds + shipping. So if the USB jig doesn't work, it's going to them!
Hello,
Don't know if this has been asked but I have been looking for it for a while. Cant seem to fine a solution.
I flashed my phone wrong with hemdall now my phone wont turn on. Screen completely black i reboot pulled out the battery everything I can think of can you give me a suggestion. I was thinking about buying a USB Jig.
I'm in the same boat and I bought the Jig. However I think Josh just acts as a middle man on this one and shipping is actually from overseas. But you can find it here. http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-s-download-mode-jig/ I suggest a little extra shipping cost.
However the other suggestion if that is not working (I think I killed my phone) is to have Josh do a Jtag on the phone. You can find that at http://mobiletechvideos.mybigcommerce.com/samsung-vibrant-jtag-brick-repair/
Can you get into download mode? Remove battery, plug usb, press up+down vol buttons and insert battery.
hey i having same problem but i could see the vibrant samsung screen but my phone won't pass that and like you say about the usb cable and then plugging the battery i can do that as well but how can i get my phone back and running another rom!!!
Monster809 said:
hey i having same problem but i could see the vibrant samsung screen but my phone won't pass that and like you say about the usb cable and then plugging the battery i can do that as well but how can i get my phone back and running another rom!!!
Click to expand...
Click to collapse
If you can see the Vibrant Samsung screen just use Odin to flash back to stock
Kabiigon said:
Hello,
Don't know if this has been asked but I have been looking for it for a while. Cant seem to fine a solution.
I flashed my phone wrong with heimdall now my phone wont turn on. Screen completely black i reboot pulled out the battery everything I can think of can you give me a suggestion. I was thinking about buying a USB Jig.
Click to expand...
Click to collapse
The real solution here i doing a JTAG to your phone or make the Unbrickable MOD (It's very dangerous, a person with Welding and electronic skills must do this).
Another thing you can do is buy a broken Screen phone from Ebay (it more cheaply) and change the motherboard!!
My suggestion would be to continue to try to get into Download mode on the phone. My phone was DEAD no life at all plugged into the wall or PC. I kept trying to get it into download mode and magically after hours of failures, ODIN recognized the device! The phone was still DEAD no life at all on the screen but ODIN had recognized that my device WAS indeed connected. So I continued to flash back to stock and as always with a little patience ODIN was there to save me. The phone automatically rebooted after ODIN was done and BOOM! Good2Go
Goodluck!
^^I'm gonna try that and hopefully with some patience it will work. Otherwise I'm also gonna be ordering a jig, they're not that expensive. My problem is the same as the OP's. My vibrant will just not give any signs of life. I was trying to odin to stock from one cosmics ics RC3.1. Wanted to start on a fresh install for AOKP build 25. But then odin decided to fail on modem.bin. then it just hung and phone turned off, haven't been able to turn it on since. I've spent the last two hours trying to put in different combinations and keys and usb attachments to bring any hints of life, but so far nothing. Bootloader update was not checked on odin so I'm pretty confident that its not due to bootloader mismatch but someone correct me if I'm wrong. Sending it back to samsung or tmobile is very far of an option since I've modified the phone to add FFC. If anyone has any advice or hints it would be greatly appreciated. I'm kind of hating myself and flashing now since I was very happy with the rom that I had and how everything was setup. I just wanted to try something new for fun and this went and blew everything up.
^^I literally held down the buttons > plugged in the cord > put in the battery > and counted in my head the amount of seconds it took the phone to "normally" boot to where I would "normally" let go of the power button to get into Download mode, lol I know it sounds ridiculous but that's how I did it. It helped that I had my sisters working Vibrant right there, I used her phone to get into download mode and timed the process and used that as a baseline for the timing of trying to get the "DEAD" Vibrant into download mode.
If all else fails a JTAG as mentioned should fix your problem fosho!
Goodluck!
Ye I fixed it. One day I did what I had been doing the whole time and it just decided to work. Got into download mode then went back to stock. Our phone is so freaking weird yet I love the damn thing. It really is unbrickable. To anyone in this situation just never give up.
Sent from my SGH-T959 using XDA App
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
If it was bricked it wouldnt turn on even a bit. Just charge it or try changing the battery.
coolstorybro_123 said:
If it was bricked it wouldnt turn on even a bit. Just charge it or try changing the battery.
Click to expand...
Click to collapse
If I try to charge it it displays the SGS2 charging screen for a few seconds and then switcher straight off.
I just got into work and tried my colleagues 2000mah battery which had 32% in it. Exactly the same problem. WTF????
Thanks
Edit: FYI, it turns off before entering download mode or recovery. WTF????
Maybe you hit this ?
VAXXi said:
Maybe you hit this ?
Click to expand...
Click to collapse
That's just what I was thinking, actually
I couldn't find a description of what actually happens when this brick happens. The page doesn't really say... Does anywhere say?
Edit: I swear I didn't even flash the Siyah RC6 that was known to brick the phones either... -_-;;
Thanks!
It's not just a specific kernel, more are actually faulty. The whole story is here.
SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
your phone is ok as far as it shows u the s2 logo
you have 2 things to do , try to go to recovery or download mode and formate data/factory reset then flash another rom , btw what kernel u used before your phone go to this situation ? if you were using stable kernel "cm,neak,fluxi,syah stable" so you are safe from hardbrick bug , and the hard brick bug is done only if you have faulty kernel and wibed your data through recovery , and this isn't your situation , so don't be afraid
evaworld said:
your phone is ok as far as it shows u the s2 logo
you have 2 things to do , try to go to recovery or download mode and formate data/factory reset then flash another rom , btw what kernel u used before your phone go to this situation ? if you were using stable kernel "cm,neak,fluxi,syah stable" so you are safe from hardbrick bug , and the hard brick bug is done only if you have faulty kernel and wibed your data through recovery , and this isn't your situation , so don't be afraid
Click to expand...
Click to collapse
Thanks for saying, but I can't get into recovery or download. The phone switches off before then!
That's what's so confusing! xD
Thanks
With a known good batter try hard resetting to download mode 2x in a row.. Hold the button config to get into download mode.. Hold it through two restarts.. Might work.
Sent from my GT-I9100 using xda premium
I've nuked mine a few times with buggy kernels, sounds like a similar situation. I got my device back by flashing CM9 resurrection, then flashing Siyah, and finally from CWM flashing an ICS-based stock ROM.
I'd suggest taking a backup of your efs unless you're selling it with stock.
Sent from my GT-I9100 using XDA
SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
i am having exactly the same problem.i did a factory reset after flashing siyah kernel (SiyahKernel v3.3.1) on Resurrection remix v2.2.let me know if you guys find any solutions
JIG
try to use a download mode JIG.
I'm not sure if a link will violate xda-rules....
google it
dont worry
if you boot up and are getting the sg2 logo then you have not bricked you phone.
to fix simply download a .tar version of any rom and run odin to pda reinstall if you wanted to you could go the whole hog and reflash a fresh cf-kernal (rooted or stock) and then flash fresh firmware. just remember to get the kernal that originally matches the (ithink) your correct baseband ie xxki4
there should be no worries aslong as you dont pull the plug.
could have had a worse error saying installation incomplete please use kies then you would have to had taken battry out reinserted and hoped the three butn combo for rec. mode worked happened to me awhile back lol
hope i helped you
ps never read your post fully just skimmd the jist of it although the above should be applicable
also try resetting your battry stats in cwm
finally fixed
thanks for the help everyone.i have fixed it now.it seems like the problem was with the updated version of siyah kernel .i managed to put the phone in download mode.(kept the phone on the charger for a while. than, i don't know some how when i tried to go to download mode it did).and flashed siyah kanel v3.2.6.4 via odin
Today i decided to try out the nocturnal rom, but before that i had to make a backup. at the the time the phone was what i would a call luke warm so i paid no mind to it. so a few minutes later i look back at the phone and notice that the screen turned off annd the phone was now averagely hot
so i let it cool down for a bit (i thought that the phone must have shut itself off in order to make sure the internals wouldn't be damaged), then when i try to turn it on the lg logo does show up but never gets to the base roms nexus boot animation, now i'm thinking that TWRP must have drained my battery because when i usually make a backup my battery can go from 94% to 50% in a span of 7 minutes (only during backup). So i leave it to charge for 30 minutes 1 hour and then 5 hours but each time i check it still won't turn on correctly.
Now i have had this happen to me before, when i had the atrix 4g this happened and i had to buy a battery only charger to even get it to work again
but as we all know that won't work for the optimus g because you cannot take out the battery.
so i have to ask, what should i do? is there any way to fix this?
Side note: can't get into recovery (seems to shut off before it loads up, its like an infinite loop of dying and turning on again) the power button still glows while its connected giving the appearance of charging but it still never boots up all the way ( the most i can get it to is the part of recovery before going into TWRP. you know holding vol+ and seeing fastboot mode)
There is thread here someone made of disassembly. You can do a battery pull pretty easily. Never know might help.
Have you tried download mode at all BTW?
Sounds more like something was deleted then a batter problem to me. If download mode works you could try lgnpst back to stock.
The information in THIS thread might be able to help.
I can't vouch for it because I haven't experienced these problems, but the OP there seemed to get his problem fixed.
GL.
Although, looking things over, sounds like you have a different issue.
So you can get to the bootloader?
from the bootloader have you tried hitting the volume down key twice then hitting power?
That should reboot you into recovery, where you can restore something or flash stock.
Edit. Quote from FreeGee post.
To enter bootloader, hold volume UP and power.
Upon entering the bootloader, you will notice that there is no 'menu' to enter fastboot or recovery. Unfortunately, since the stars didn't align properly, we were unable to tell the new bootloader where to load the images that contain the menu from.
In light of that, you'll have to navigate the menu blind. Use the volume keys to change selection, and the power key to select.
The choices are (in order of pressing volume down):
Start - boot the phone normally [already selected]
Restart Bootloader - reboot into the bootloader
Recovery Mode - enter recovery (CWM)
Power Off - powers the phone off
So, to get to Recovery, you would press volume down twice then power.
Click to expand...
Click to collapse
bleached45 said:
The information in THIS thread might be able to help.
I can't vouch for it because I haven't experienced these problems, but the OP there seemed to get his problem fixed.
GL.
Although, looking things over, sounds like you have a different issue.
So you can get to the bootloader?
from the bootloader have you tried hitting the volume down key twice then hitting power?
That should reboot you into recovery, where you can restore something or flash stock.
Edit. Quote from FreeGee post.
Click to expand...
Click to collapse
when i try to get into TWRP it doesnt start up, same as when it trys to turn on, it seems to die before it boots fully or so to say the screen
goes from a backlit black to just black and then it doesn't come on again. (looking at thread and nothing has worked yet i'm now trying last advice in thread since my phone won't even turn on unless its connected to the charger)
also i have no idea what download mode is but since nothing seems to be working i will assume that does not work either
Edit: actually maybe i can lgnpst. all i have to do is be able to get into the bootloader right? going to try in the afternoon.
Kurodo said:
when i try to get into TWRP it doesnt start up, same as when it trys to turn on, it seems to die before it boots fully or so to say the screen
goes from a backlit black to just black and then it doesn't come on again. (looking at thread and nothing has worked yet i'm now trying last advice in thread since my phone won't even turn on unless its connected to the charger)
also i have no idea what download mode is but since nothing seems to be working i will assume that does not work either
Edit: actually maybe i can lgnpst. all i have to do is be able to get into the bootloader right? going to try in the afternoon.
Click to expand...
Click to collapse
Sorry none of that is working.
To enter download mode:
Connect phone to computer, power off, and then power on, holding down the power button and both volume buttons
Click to expand...
Click to collapse
In the FAQ section of THIS thread, it explains how to use LGNPST.
This is god's way of telling you not to mess with flashing roms on your phone. Hopefully you will learn your lesson and keep your dirty hands off your phone, it just wants to be left alone!!!!!!!
sent from my Nexus 4 using xda premium
jamesc760 said:
This is god's way of telling you not to mess with flashing roms on your phone. Hopefully you will learn your lesson and keep your dirty hands off your phone, it just wants to be left alone!!!!!!!
sent from my Nexus 4 using xda premium
Click to expand...
Click to collapse
I can't tell if you're being serious or not
to that nay sayer
jamesc760 said:
This is god's way of telling you not to mess with flashing roms on your phone. Hopefully you will learn your lesson and keep your dirty hands off your phone, it just wants to be left alone!!!!!!!
sent from my Nexus 4 using xda premium
Click to expand...
Click to collapse
There is beauty in god given stock but there is TRUE beauty in the purgatory that is flashing roms and making it all your own!!!!!!:laugh:
last resorts
well the lgnpst did work but the battery still won't charge, so if i can't get a replacement i'll try this http://forum.xda-developers.com/showthread.php?t=2039707 and see if i can charge it.
now a different question...
does anyone know if i can exchange the phone at an att store if i bought it from amazon or would i have to go through amazon?
and exactly how does that work?
Kurodo said:
well the lgnpst did work but the battery still won't charge, so if i can't get a replacement i'll try this http://forum.xda-developers.com/showthread.php?t=2039707 and see if i can charge it.
now a different question...
does anyone know if i can exchange the phone at an att store if i bought it from amazon or would i have to go through amazon?
and exactly how does that work?
Click to expand...
Click to collapse
Amazon is actually VERY easy to deal with, and a HELL of a lot easier than AT&T. They'll ship you out a replacement, you send the old one back once you receive the new one. Done. You MAY have to send the old one first, but if you let them put a hold on a credit card, I believe they'll definitely ship first.
You may be able to fix this by holding down both the volume down and power buttons for at least 45 seconds after you plug in the phone.
so
STEP 1: PLUG IN PHONE
STEP 2: PRESS AND HOLD THE VOLUME DOWN AND POWER KEYS TOGETHER FOR AT LEAST 45 SECONDS
STEP 3: LEAVE PLUGGED IN FOR TEN MINUTES
STEP 4; BOOT INTO RECOVERY MODE, WIPE BATTERY STATS, WIPE CACHE, AND WIPE DALVIK, THEN REBOOT TO SYSTEM FROM WITHIN RECOVERY.
LAST PART IS TO PREVENT IT FROM HAPPENING AGAIN.
I've gone the three of these for various reasons and some times lgnpst pretends to work and you need to do it again. And some times you need to wipe data boot back into download and do it again. This phone is retarded.