Related
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
I've had my Prime for two days, my protector has not come in yet and I just noticed a deep vertical scratch right in the center of my screen. I have no idea how it happened, but it was not there an hour ago.
Is there anything I can do?
quile22 said:
I've had my Prime for two days, my protector has not come in yet and I just noticed a deep vertical scratch right in the center of my screen. I have no idea how it happened, but it was not there an hour ago.
Is there anything I can do?
Click to expand...
Click to collapse
Not really. The screen protector may hide the blemish once it is applied. Usually wet application protectors do the best at that.
You could send it back to Asus but you'll have to cough up some cash for the screen replacement.
I thought it was near impossible to scratch Gorilla Glass?
The timing of this thread is impeccable.
I've concluded that the gorilla glass on my TFP is like butter compared to my Droid X. I've already induced several DEEP scratches on my TFP, and my droid x is nearly spotless after 1.5 years of ownership.
I had originally dismissed a screen protector as unneccesary, however tonight i have applied a skinomi one that came with my carbon fiber skin as i don't have much faith in this screen.
TF201 | XDA Premium
I was amazed that this happened too. I thought I could last a few days until my protector came in. I even went as far as taking my keys to my screen on the corner after I made my original post to see what was up. NOTHING. Not a single scratch.
I have no idea how this happened or what caused it.
Did putting on the screen protector hide the scratches?
keys won't scratch glass. All those key tests mean nothing. the chemical composition of keys (brass 99% of the time) is not hard enough to scratch glass. You might as well rub a marshmallow on your screen.
Sent from my Galaxy Nexus using Tapatalk
Well at least there is something good to come from the faulty wifi and gps. Just exchange it from wherever you bought it and tell them that the gps isn't working right.
thetruth1983 said:
Well at least there is something good to come from the faulty wifi and gps. Just exchange it from wherever you bought it and tell them that the gps isn't working right.
Click to expand...
Click to collapse
lol, was thinking the samething
Anyone ever try the banana peel trick to resolve scratches as shown on YouTube? Lol
The screen on my TF101 scratched really easy. Fortunately about a week after this first happened something started peeling up between the screen layers. I returned it to ASUS for the peeling issue and it came back with a new screen. Sold the device straight away because I thought I wanted the TF201. Cancelled that order once the GPS issue became apparent.
My Prime came out-of-the-box with a couple of scratches on the screen. I have considered returning it, but have eventually decided that they're not noticeable unless in the correct light, and because I'm otherwise happy with my device, I don't want to risk exchanging it for one that has dead pixels/backlight bleed/no haptic feedback.
There are a number of ways to remove scratches from glass or CDs. I've tried this method and it does work, although I can't say how well it will wear on a touch surface.
If you use this in conjunction with a screen protector, suggest a "dry" protector as opposed to the wet-apply type.
http://www.wonderhowto.com/how-to-remove-scratches-lcd-cd-with-egg-143178/
This is for plastic, not glass.
After watching a few vids on egg and alum, this might actually work. As far as I can tell there are no abrasives, so it must "fill" the scratches. If that's the case, it should work on glass all the same.
I went ahead and got an RMA for the until for the GPS issue. It has never worked with any combination of wifi/bt on/off.... and I'm not talking about locking, it doesn't even see any satellites. When calling they suggested I just return it, but I like it and don't want to wait 3+ months for a new one.
I will try the egg white trick before sending it in and report back.
Hopefully they will just give me a new unit.
Even though my phone doesn't have Gorilla Glass, this was posted in our forum as a fix for scratches on this type of glass. Apparently it works. You might want to try it out.
Fix here
So i installed my skinomi screen protector since my other one was scratched and got water under the screen somehow.. Thought it would dry up but it's pretty bad and it's been 24 hours now.. Also there seems to be something wrong and the bottom right of the screen has brighter light coming through in lines. What do i need to replace if i ever choose to get a new screen, a digitizer? I'm not sure what to buy to fix this and any suggestions on where to get a good one. I know the ones on ebay are cheap but i'm afraid they might be bad or something. Any help would be great as this could have been avoided if i didn't use too much solution. Only if i could go back in time....
Try using a blow dryer on low heat near the screen.
I did that, i think i did everything possible. The grey spots probably don't worry me as much because i have a feeling they'll dry out but what's worrying me is the screen seemed to have white lines that are getting bigger and spreading a bit. It's not completely white but it's a lot brighter than other areas. I had to bite the bullet today and use it because of emergency or else i would have let it dry for a few days. I'll take a picture tomorrow afternoon to show what it looks like.
If someone can help i'm planning to open it up and try to clean the screen but if it doesn't get cleaned all the way what would i need to buy to replace it, the LCD screen or a digitizer? I was thinking the LCD because the digitizer is mostly just a glass screen that usually doesn't need replacing unless it's cracked right?
Right, but there's a pretty decent chance you'll crack the digitizer when removing it from the LCD, so you may as well order the complete assembly...should be around $45.
Well i forgot to take a picture today but i'll take one tomorrow of the before and after. I'm receiving my pry and screwdriver set tomorrow and i'll try to clean it before trying to replace this. I'll report how it goes.
uEih said:
Well i forgot to take a picture today but i'll take one tomorrow of the before and after. I'm receiving my pry and screwdriver set tomorrow and i'll try to clean it before trying to replace this. I'll report how it goes.
Click to expand...
Click to collapse
You'll have to be very careful. I was and I still screwed the digitizer trying to clean out some water I had under mine. I ended up having to order a new lcd+digitizer combo.
yareally said:
You'll have to be very careful. I was and I still screwed the digitizer trying to clean out some water I had under mine. I ended up having to order a new lcd+digitizer combo.
Click to expand...
Click to collapse
Yea i did it and was very careful, it wasn't perfect but i didn't crack it or anything, just a little part on the corner that seemed to peel the adhesive off from the digitizer so it looks a bit ugly there. The LCD is completely clean and i cleaned under the digitizer and turned the phone back on but unfortunately it wasn't water in between the digitizer and LCD, the water seemed to be in the LCD so i just went ahead and ordered a new digitizer + LCD combo so they'll be easier to install as a whole than separate.
Apart from all that the screen seemed to have gotten more grey covered on it. I'm not sure if the grey spots are the water marks or the brighter spots because as time passes there are more grey spots covering the screen. Not like it matters anymore.
Also i bought the digitizer + LCD from ebay from hong kong cause it's the cheapest and i feel as if they're manufactured there anyways so there shouldn't be a problem in quality?
Sucks that it had to end up like this, i've never had problems installing wet protectors but i think i'm staying far away from them now...
i recently dropped my phone and it got a crack in the bottom right corner around the back button stretching up to the middle of the left hand side of the screen, and i need help repairing it.
Im not sure if i can just replace the glass myself or i need to replace the digitizer or any other parts as the screen and back button still work perfectly fine.
I'd also like to know whether this job is easy enough to do at home as i am on a low budget, however i dont have much experience fixing phones.
much appreciated if anyone can help me
Replace the screen assembly, glass plus digitiser and oled screen. Trying to unglue the glass is very hard and the heat can kill the phone.
boomboomer said:
Replace the screen assembly, glass plus digitiser and oled screen. Trying to unglue the glass is very hard and the heat can kill the phone.
Click to expand...
Click to collapse
Replacing the whole digitiser is a lot easier, but beware cheap(ish) ebay parts - I replaced my digitiser with an assembly from ebay, but the glass in the replacement broke very easily.... replaced it again and it's cracked again, without even having a hard knock. Nowehere near as sturdy as OEM parts. Screen still works so leaving it for now
Words of warning...
I attempted to replace the glass on my S3 after I dropped it. I have over 20 years experience as a computer engineer and access to loads of tools. I watched numerous YouTube videos on the process before I started yet still I managed to break the digitiser. In the end I bit the bullet and bought another brand new S3 for £200. The cheapo replacement glass I bought from eBay did not seem very sturdy either - I'm certain it's not gorilla glass. My advice would be to get it fixed professionally by someone who uses OEM parts but then again, how close in price would that be to a brand new phone?
I've just dropped my three month old Honor 7 and the screen is cracked from the bottom right corner. I bought it new from Amazon UK (sold by Amazon EU S.a.r.L.), it wasn't through Vmall. Is the screen covered under any form of warranty? If not, where's the cheapest place to get it fixed in the UK?
GrandMasterPlank said:
I've just dropped my three month old Honor 7 and the screen is cracked from the bottom right corner. I bought it new from Amazon UK (sold by Amazon EU S.a.r.L.), it wasn't through Vmall. Is the screen covered under any form of warranty? If not, where's the cheapest place to get it fixed in the UK?
Click to expand...
Click to collapse
I think the screen is guaranteed against manufacturing faults, but not the glass against accidental damage.
When I trod on mine in the back of a car, I called Hihonor support and they quoted me £70-80 + £15 inspection and postage charge, which I thought was reasonable, however when calling their repair centre to book mine in they laughed and said it would be at least £130 for Honor 7 screen replacement - they can't do just the glass as it's all bonded to the digitiser and screen.
I decided to buy a new screen (with glass, digitiser and interior frame attached) from eBay for about £40 and fitted it myself. Not as easy as the videos on youtube make it look - it is very difficult to get apart for a start, then the battery is hard to remove. Also, various parts (including all the buttons, vibration motor etc have to be heated with a hairdryer to separate them from the old screen frame and re-installed into the new frame.
Luckily mine is working perfectly now, although I think the screen may not be quite as bright as the original one was.
I wouldn't try to buy just the glass, or even the glass and screen (without the frame) - you'll never get it to look as good as new.
Good luck and let us know how you get on with having it repaired or doing it yourself.
You can PM me if you need any advice
honorable said:
I think the screen is guaranteed against manufacturing faults, but not the glass against accidental damage.
When I trod on mine in the back of a car, I called Hihonor support and they quoted me £70-80 + £15 inspection and postage charge, which I thought was reasonable, however when calling their repair centre to book mine in they laughed and said it would be at least £130 for Honor 7 screen replacement - they can't do just the glass as it's all bonded to the digitiser and screen.
I decided to buy a new screen (with glass, digitiser and interior frame attached) from eBay for about £40 and fitted it myself. Not as easy as the videos on youtube make it look - it is very difficult to get apart for a start, then the battery is hard to remove. Also, various parts (including all the buttons, vibration motor etc have to be heated with a hairdryer to separate them from the old screen frame and re-installed into the new frame.
Luckily mine is working perfectly now, although I think the screen may not be quite as bright as the original one was.
I wouldn't try to buy just the glass, or even the glass and screen (without the frame) - you'll never get it to look as good as new.
Good luck and let us know how you get on with having it repaired or doing it yourself.
You can PM me if you need any advice
Click to expand...
Click to collapse
Thanks dude, much appreciated. I was into it until you started mentioning removing parts by heating them up then thought I'll leave it to the experts. :laugh: Honor UK have quoted me £80 as it's a pretty clean break so I'm going to give them a go and see what they say. If they do the same as they did for you, which they said they wouldn't!, then I'll go with that. Will let you know.
I'm surprised their aren't more threads on hear about replacing screens because this phone does feel fragile despite being reasonably weighty so I'd have thought there'd be loads of cracked screens out there. I dropped my old S5 a couple of times from higher up and the screen survived both times. Am now thinking a tempered glass protector might be in order for the 7 :fingers-crossed:
Mine had a glass protector, but I guess they don't cope with treading on! I've put one on the new screen too.
I also have an S-line gel case which acts as a bit of a buffer against drops.
Let us know if you get yours done for £80
honorable said:
Mine had a glass protector, but I guess they don't cope with treading on! I've put one on the new screen too.
I also have an S-line gel case which acts as a bit of a buffer against drops.
Let us know if you get yours done for £80
Click to expand...
Click to collapse
After reading reviews of the official Honor repair company, SBE Limited, and how they appear to be happy to scam people I thought I'd have a go myself. So I bought a replacement front glass and thought I'd give it a go.
Dissembling the phone is really easy, once you've got the hang of the clips holding the back on, and taking it all apart was easy. What wasn't so easy (read nigh-on impossible) is separating the front glass from the digitiser. I tried and tried and in the end the touch screen just split into a number of layers so I'll need to order the complete screen assembly. My concern is you mentioned you bought one off ebay and it wasn't as bright as the original. From this I'm guessing it wasn't an original screen? I'd like to get an original if I can. Do you have a link to the one you bought? How long did it take coming from China?
Don't know if this is relevant but under the hicare app it allows you to price up replacement parts. Could not find any mention of the Honor 7 but it did list the Honor 5X as £35 so might be worth trying this way to see if they do have the Honor 7.
I got mine from eBay seller called bestsellstuff.
£35.27 at the moment and mine came quicker than expected with 2nd class delivery free.
I don't think any of the eBay sellers will say they are genuine screens, but I think they probably all are - I can't imagine they would be cheap to replicate. Maybe they are seconds or find their way out of the factory somehow....
boroleigh said:
Don't know if this is relevant but under the hicare app it allows you to price up replacement parts. Could not find any mention of the Honor 7 but it did list the Honor 5X as £35 so might be worth trying this way to see if they do have the Honor 7.
Click to expand...
Click to collapse
Thanks for the nod. Tried it but no joy. For some reason they don't support the Honor 7. Very Huawei tbh, they're left hand doesn't know what the right is doing. A bit all over the place.
honorable said:
I got mine from eBay seller called bestsellstuff.
£35.27 at the moment and mine came quicker than expected with 2nd class delivery free.
I don't think any of the eBay sellers will say they are genuine screens, but I think they probably all are - I can't imagine they would be cheap to replicate. Maybe they are seconds or find their way out of the factory somehow....
Click to expand...
Click to collapse
Great stuff, have just ordered the last one they had in stock in they're in France also, so should be quicker than coming from Hong Kong. Funny thing is I hadn't seen their add before, it hadn't come up with my ebay search for 'Honor 7 replacement screen'. Without having the name I'd not have found it and paid more so thanks again! :good:
Here are a few tips for when it arrives:
Don't peel off any of the blue plastic film until you're ready to do each part - it's very sticky underneath.
Take photos as you go along incase you need to go back a astep.
I'm not sure if you got to the stage of removing the battery before - it is stuck down very strongly. I just gradually prised mine out, but you might find heating it a bit will release it easier. There aren't any cables underneath it (as some other Honors have).
When heating (with a hairdryer) the small bits of circuit board and components that need to be transferred to the new frame, only do it for long enough to get them to peel off (I used tweezers to do this).
When you come to install each part, there are very small bumps in the frame that you need to line up the equally small holes on the part - makes positioning them easy! Then use a plastic tool to press them firmly onto the frame.
When you come to put everything back, make sure that the very small narrow ribbon cable that goes under the tiny flip-up bracket (the connection to the smart key) goes in fully until it stops. I didn't put mine in completely and the smart key wouldn't work until I re-did it properly.
You may notice that there is a square-ish hole and some slots in the frame (under where the battery goes?) on the new frame which aren't on the old one. If so, you might want to cover them up with some black gaffa tape or thin card - I suspect they are the cause of some light areas at the very sides of my screen, but I don't want to strip mine down again.
honorable said:
Here are a few tips for when it arrives:
Don't peel off any of the blue plastic film until you're ready to do each part - it's very sticky underneath.
Take photos as you go along incase you need to go back a astep.
I'm not sure if you got to the stage of removing the battery before - it is stuck down very strongly. I just gradually prised mine out, but you might find heating it a bit will release it easier. There aren't any cables underneath it (as some other Honors have).
When heating (with a hairdryer) the small bits of circuit board and components that need to be transferred to the new frame, only do it for long enough to get them to peel off (I used tweezers to do this).
When you come to install each part, there are very small bumps in the frame that you need to line up the equally small holes on the part - makes positioning them easy! Then use a plastic tool to press them firmly onto the frame.
When you come to put everything back, make sure that the very small narrow ribbon cable that goes under the tiny flip-up bracket (the connection to the smart key) goes in fully until it stops. I didn't put mine in completely and the smart key wouldn't work until I re-did it properly.
You may notice that there is a square-ish hole and some slots in the frame (under where the battery goes?) on the new frame which aren't on the old one. If so, you might want to cover them up with some black gaffa tape or thin card - I suspect they are the cause of some light areas at the very sides of my screen, but I don't want to strip mine down again.
Click to expand...
Click to collapse
Great tips, thanks again. I'll be sorting it as soon as it arrives. Will report on how I get on.
honorable said:
Here are a few tips for when it arrives:
Don't peel off any of the blue plastic film until you're ready to do each part - it's very sticky underneath.......
Click to expand...
Click to collapse
Sorted!! Thanks for the advice, was really useful. Took it all on board, took my time (about 1hr) and fitted the new screen. Clipped it all back together and worked perfect first time. £35 to get your screen fixed, amazing. I'll always fix a cracked screen from now on, these repair companies are just profiteering.
Thanks again.
GrandMasterPlank said:
Sorted!! Thanks for the advice, was really useful. Took it all on board, took my time (about 1hr) and fitted the new screen. Clipped it all back together and worked perfect first time. £35 to get your screen fixed, amazing. I'll always fix a cracked screen from now on, these repair companies are just profiteering.
Thanks again.
Click to expand...
Click to collapse
Great news!!
Did you have to cover the square hole and slot to stop light leakage?
Also, is there any light bleeding at the sides and is there any difference in brightness from the original screen?
honorable said:
Great news!!
Did you have to cover the square hole and slot to stop light leakage?
Also, is there any light bleeding at the sides and is there any difference in brightness from the original screen?
Click to expand...
Click to collapse
The screen and housing isn't original Huawei, it's a pattern unit but tbh it looks totally identical in use, no less dim than the original screen. There's also no bleed at all. There weren't any hollows and slots to fill with card under the battery. The only hollow was at the base of the battery as it sat slightly higher up (towards the top of the phone when laid flat) in the casing so I filled that with folded card.
The only slight issue is that the screen shape (rounded corners of the glass) when looking at the phone from the front doesn't fit into the corners of the casing absolutely perfectly. Tbh only a phone nut would notice it, wouldn't be an issue to anyone else.