Hey guyz
I flashed siyah kernel
Then I tried dual boot wid sammy jb (1st ROM) and cm10.1 as second.
However I wasnt able to boot to second ROM and I had just black screen
Then I removed 2nd ROM
And tried to boot into primary
But got a bootloop.
Then i wiped cache dalvik cache and partition cache.. Still no luck
Then I restored nandroid.
No luck
Then I flashed stock ROM wid odin
Still no luck
What am I missing.. M new to Samsung..
doctor_droid said:
Hey guyz
I flashed siyah kernel
Then I tried dual boot wid sammy jb (1st ROM) and cm10.1 as second.
However I wasnt able to boot to second ROM and I had just black screen
Then I removed 2nd ROM
And tried to boot into primary
But got a bootloop.
Then i wiped cache dalvik cache and partition cache.. Still no luck
Then I restored nandroid.
No luck
Then I flashed stock ROM wid odin
Still no luck
What am I missing.. M new to Samsung..
Click to expand...
Click to collapse
What ur missing for now is a little commonsense to Read before doing anything silly
1)U should be aware (if not get it now), that u cannot Dual boot Stock Samsung JB4.1.2 or Roms based on it, unless they are modified.
2) Siyah doesn't support Rom's like CM10.1 which is based on Android 4.2.2 properly.
3) Dual boot not wrk'ng with JB 4.1.2 (stock samsung/and roms based on it) is due to the reason that they use 'Preload partition' which is required as 'Secondary rom-partition' for Dual boot .
4) which is the reason why u werent able to boot CM10.1 in the firsrt place and could'nt restore/boot back the stock JB (reason being the data in the preload/secondary rom partition being deleted)
5) now start afresh by installing/flashing a stock JB rom via ODIN.
He he he I read siyah doesn't support jb dual boot still was stupid enough to try :/ ...
And as I mentioned...flash stock still doesn't let it boot... I see Samsung and then boot loop
Sent from my GT-I9100 using Tapatalk 2
doctor_droid said:
He he he I read siyah doesn't support jb dual boot still was stupid enough to try :/ ...
And as I mentioned...flash stock still doesn't let it boot... I see Samsung and then boot loop
Sent from my GT-I9100 using Tapatalk 2
Click to expand...
Click to collapse
try flashing a custom kernel like 'Philz' from Odin, then enter its recovery and do full wipe including 'Preload',after that try flashing either a stock rom from odin or a Stock based custom rom like 'Neat rom' or 'Alliance Rom' from philz recovery and see
Sun90 said:
try flashing a custom kernel like 'Philz' from Odin, then enter its recovery and do full wipe including 'Preload',after that try flashing either a stock rom from odin or a Stock based custom rom like 'Neat rom' or 'Alliance Rom' from philz recovery and see
Click to expand...
Click to collapse
Sure will try and let u knw...currently m able to boot official cm and enjoying it... bt having poor battery
Sent from my GT-I9100 using Tapatalk 2
Sun90 said:
try flashing a custom kernel like 'Philz' from Odin, then enter its recovery and do full wipe including 'Preload',after that try flashing either a stock rom from odin or a Stock based custom rom like 'Neat rom' or 'Alliance Rom' from philz recovery and see
Click to expand...
Click to collapse
okay i flashed philz kernel ... formated /wiped data ,dalvik,system,cache preload, ... flashed neat rom.. success... then i tried flashing stock rom.. got a bootloop after seeing samsung logo...
i can restore nandroid of cm10.1
bt restoring nandroid of pure stock gives bootloop.
Sounds like your problem is to do with the /preload folder. To restore a stock nandroid, you also have to restore the preload folder associated with that backup. Search on xda for hawkerpaul's backup and restore scripts for preload, and read his OP on how to use them. That should get you sorted. As you wouldn't have already backed it up from the sound of things, you might not have any luck restoring that exact stock backup, and may have to reflash. If you need to extract data from the nandroid, titanium backup can extract data from a nandroid.
Sent from my GT-I9100: Powered by Dorimanx, running RootBox
Related
Hello, I hope this is the right group.
I have spent the last 2 days trying to get JB working on my SGS2. I previously had ICS Hydra h2o 1.4.1 ROM on my device.
The troubles started when I tried booting into CWM recovery. The phone wouldn't go past the yellow triangle so I had to use ODIN to flash stock Samsung ICS ROM on the phone to get it working again. I have since tried multiple JB ROMs with different kernels but most of them get past the yellow triangle but then stop on logos varying between kernels. I am also unable to boot into CWM recovery and must flash a CF-Root kernel using ODIN to get into recovery.
It is strange that this happens only with JB ROMs and I have no trouble installing Hydra h2o again through recovery.
I always use the same method of installing ROMs through CWM:
- wipe data/factory reset
- wipe cache
- wipe dalvik
- install .zip from sdcard
I have also tried fixing permissions before and after flashing ROMs, nothing seems to get me into the OS.
One ROM, Vanilla RootBox, I have found to sometimes boot all the way into the OS but the system frequently freezes and is unstable. Looks amazing tho.
Do you have any ideas on how I could get JB ROMs working with my SGS2? Is there anything I am missing?
SynGates said:
Hello, I hope this is the right group.
I have spent the last 2 days trying to get JB working on my SGS2. I previously had ICS Hydra h2o 1.4.1 ROM on my device.
The troubles started when I tried booting into CWM recovery. The phone wouldn't go past the yellow triangle so I had to use ODIN to flash stock Samsung ICS ROM on the phone to get it working again. I have since tried multiple JB ROMs with different kernels but most of them get past the yellow triangle but then stop on logos varying between kernels. I am also unable to boot into CWM recovery and must flash a CF-Root kernel using ODIN to get into recovery.
It is strange that this happens only with JB ROMs and I have no trouble installing Hydra h2o again through recovery.
I always use the same method of installing ROMs through CWM:
- wipe data/factory reset
- wipe cache
- wipe dalvik
- install .zip from sdcard
I have also tried fixing permissions before and after flashing ROMs, nothing seems to get me into the OS.
One ROM, Vanilla RootBox, I have found to sometimes boot all the way into the OS but the system frequently freezes and is unstable. Looks amazing tho.
Do you have any ideas on how I could get JB ROMs working with my SGS2? Is there anything I am missing?
Click to expand...
Click to collapse
Follow this:
-boot to CWM recovery
-wipe data /factory reset
-wipe dalvik cache (under advanced)
-format /system (under mount and storage)
-flash ROM
-flash Gapps (for jelly bean)
-fix permissions
-reboot phone
Done
Swyped from my Samsung Galaxy SII
Thank you for the reply, but that method does not seem to work either.
One thing I have noticed though is when I select wipe data/factory reset it reports an error formatting /sdcard/.android_secure.
Is this something that could be causing my problems?
SynGates said:
Thank you for the reply, but that method does not seem to work either.
One thing I have noticed though is when I select wipe data/factory reset it reports an error formatting /sdcard/.android_secure.
Is this something that could be causing my problems?
Click to expand...
Click to collapse
Nope
Swyped from my Samsung Galaxy SII
SynGates said:
Thank you for the reply, but that method does not seem to work either.
One thing I have noticed though is when I select wipe data/factory reset it reports an error formatting /sdcard/.android_secure.
Is this something that could be causing my problems?
Click to expand...
Click to collapse
which kernel u were into while flashing the JB rom?
Use siyah or dorimanx kernel it works fine for me must be your kernel
Sun90 said:
which kernel u were into while flashing the JB rom?
Click to expand...
Click to collapse
When I'm flashing I'm using XLPB kernel with CF-root. That's the kernel I flash to get into CWM when the ROMs misbehave.
SynGates said:
When I'm flashing I'm using XLPB kernel with CF-root. That's the kernel I flash to get into CWM when the ROMs misbehave.
Click to expand...
Click to collapse
try this.
after flashing Cf-root kernel from ODIN.
1) flash the .zip file of siyah kernel v3.5.2 for S2, dwnld the same Here.
2)after that reboot into siyah kernel recovery.
3) wipe data/factory reset, then wipe cache and dalvik.
4) flash the JB rom zip file(Vanilla root box).
5)reboot ur phone and see.
ps- before doing wipes and rom flash do please backup ur exsisting rom once ur into siyah kernel recovery first
Sun90 said:
try this.
after flashing Cf-root kernel from ODIN.
1) flash the .zip file of siyah kernel v3.5.2 for S2, dwnld the same Here.
2)after that reboot into siyah kernel recovery.
3) wipe data/factory reset, then wipe cache and dalvik.
4) flash the JB rom zip file(Vanilla root box).
5)reboot ur phone and see.
ps- before doing wipes and rom flash do please backup ur exsisting rom once ur into siyah kernel recovery first
Click to expand...
Click to collapse
Gives me Kernel panic or stops at the triangle loading screen. Seems the only way to get into CWM is through CF-root.
SynGates said:
Gives me Kernel panic or stops at the triangle loading screen. Seems the only way to get into CWM is through CF-root.
Click to expand...
Click to collapse
Use a newer version of siyah or dorimanx, they should work fine
Sent from my GT-I9100 using xda app-developers app
I have tried three versions of syiah, including 4.1.4 but I will try dorimanx and report with the results.
edit: dorimax kernel is the same.
One thing I noticed tough is whenever I wipe dalvik cache the system reports "unknown volume for /ext-sd blablabla" - maybe this is connected to my problem?
I am at a complete stop...
No JB kernels seem to work whatsoever. Is there any wit to flash the bootloader? Or is that even possible?
I really would like to get JB working on my device.
There must be something about the previous state of my phone, some files or folders that are in the way or are missing or somewhat. Is there any way to completely reset the phone? Not just factory resetting it since that is not working.
edit: Progress! These are my steps:
- Downloaded fresh stock Samsung ROM and another version of CF-root.
- Flashed stock ROM and then CF-root kernel.
- Booted into recovery and did the whole wipe.
- Flashed .zip twice (don't know if that did the trick or what)
- Wipe dalvik cache and fix permissions.
After that the phone booted normally and I'm now running ResurrectionRemix with Android 4.1.1, hoping it wil be awesome as ****.
I installed 4.1.2 on my s2 gt i9100 no brand but will not start, crashes on startup with the samsung logo. Why?
I now have the phone down, I think I have to replace the 4.0.3
this is the tread http://forum.xda-developers.com/showthread.php?t=1544487
Did you use CWM recovery wipe? Maybe it's emmc brick bug?
It can't be a brick as it is turning on
And it's flashable with Odin, not CWM.
Sent from the Matrix
mar10o said:
Did you use CWM recovery wipe? Maybe it's emmc brick bug?
Click to expand...
Click to collapse
CWM doesn't have the emmc bug, Its a bug in the stock 4.0.4 recovery.
Conte94 said:
I installed 4.1.2 on my s2 gt i9100 no brand but will not start, crashes on startup with the samsung logo. Why?
I now have the phone down, I think I have to replace the 4.0.3
this is the tread http://forum.xda-developers.com/showthread.php?t=1544487
Click to expand...
Click to collapse
This is most likely because you have just flashed 4.1.2 without wiping old rom data. Its advised on just about every single rom thread to wipe before flash. If you dont want to lose apps/appdata then use Titanium Backup Pro.
TheATHEiST said:
CWM doesn't have the emmc bug, Its a bug in the stock 4.0.4 recovery.
This is most likely because you have just flashed 4.1.2 without wiping old rom data. Its advised on just about every single rom thread to wipe before flash. If you dont want to lose apps/appdata then use Titanium Backup Pro.
Click to expand...
Click to collapse
you have made a backup of the app + system data with titanium. also save photos, music and video
I did not think to flash a firmware I had to clean everything, I thought it was enough to download the file, put the phone in download mode with odin and startare
now how do I proceed? I wipe the 3 as I did for the rom?
Conte94 said:
you have made a backup of the app + system data with titanium. also save photos, music and video
I did not think to flash a firmware I had to clean everything, I thought it was enough to download the file, put the phone in download mode with odin and startare
now how do I proceed? I wipe the 3 as I did for the rom?
Click to expand...
Click to collapse
1) Put ur phone into dwnld mode and flash a stock ICS 4.0.3 firmware using ODIN to make ur phone up and running.
2) after that root ur phone by flashing the tar file of Siyah kernel v5.0.1 vide ODIN.
3) then reboot to siyah kernel recovery and wipe Data/factory reset and the wipe cache partition.
4)Dwnld the stock JB firmware from that link u provided and flash the same using ODIN
that way u will have a clean install of stock JB on ur phone
but if by dalal recovery without installing the 4.0.3 and do the wipe, and then install the 4.1.2 is not good?
Conte94 said:
but if by dalal recovery without installing the 4.0.3 and do the wipe, and then install the 4.1.2 is not good?
Click to expand...
Click to collapse
u can give it a try that way and post ur Success/Failure feed back over here
IMO the best bet is what i stated in my earlier post
Sun90 said:
u can give it a try that way and post ur Success/Failure feed back over here
IMO the best bet is what i stated in my earlier post
Click to expand...
Click to collapse
He has no need to do what you said and install rom twice. All he needs to do is flash kernel like Siyah v6 beta4, reboot into download mode, wipe data and then flash his stock rom via download. No need to install 4.0.3 first its just waste of time.
and where can I download the file of Siyah kernel v5.0.1?you say the kernel?
I installed the 4.1.2 doing the wipe, and everything went ok.
so every time I install a new firmware should I do the wipe right?
and then I do not have siyah kernel but everything went well from recovery
Conte94 said:
I installed the 4.1.2 doing the wipe, and everything went ok.
so every time I install a new firmware should I do the wipe right?
and then I do not have siyah kernel but everything went well from recovery
Click to expand...
Click to collapse
Good:good:
Yes, its always better to do the wipes first for a clean install, as u can see in ur case itself
Enjoy the rom for now and no need to worry about siyah kernel for now
ok
however, once I had siyah then I removed
thank you very much for your help, I did not know I had to do so for the firmware
thank you very much
Hello,
I was trying to do a factory reset on my S2, and I noticed it doesn't delete my other files (Music, Photos, Etc.) but it does reset my apps installed. Because I want to totally erase my files, I went to recovery mode and did a wipe, and I think I may have wiped the data, system, dalvic, etc on the process. And now my phone wont boot up. It is stuck at the Siyah logo (Because I flashed siyah on it before and it was a success). After this, I tried to flash siyah again into my device and its still stuck. I dont know what to do anymore, I also tried factory resetting using recovery mode. I have flashed other kernels but it still doesn't work. BTW I am using a jelly bean device
Newbees said:
Hello,
I was trying to do a factory reset on my S2, and I noticed it doesn't delete my other files (Music, Photos, Etc.) but it does reset my apps installed. Because I want to totally erase my files, I went to recovery mode and did a wipe, and I think I may have wiped the data, system, dalvic, etc on the process. And now my phone wont boot up. It is stuck at the Siyah logo (Because I flashed siyah on it before and it was a success). After this, I tried to flash siyah again into my device and its still stuck. I dont know what to do anymore, I also tried factory resetting using recovery mode. I have flashed other kernels but it still doesn't work. BTW I am using a jelly bean device
Click to expand...
Click to collapse
did you fix permissions ?
slimlo said:
did you fix permissions ?
Click to expand...
Click to collapse
Sorry I'm nub, what is permissions? Can I find that on recovery mode?
Newbees said:
Sorry I'm nub, what is permissions? Can I find that on recovery mode?
Click to expand...
Click to collapse
yep in recovery mode
I found the fix permission Sir. Shall I flash again the kernel and do a fix permission?
Sir, it's still stuck at the Siyah logo
If you've formatted system as you say you will need to flash a rom, I'm running the latest neatrom lite, I'm confused by your post its 4am here
Sent from my GT-I9100 using Tapatalk 2
Hello sir, sorry if I disturbed your sleep XD no I did not flash a ROM. I just flashed a kernel using ODIN. Should I flash a ROM?
If I flash a new ROM, say the latest Snapdragon for S2 will the kernel be included in the package? I still cant pass the logo screen even though I have flashed different kernels
Newbees said:
If I flash a new ROM, say the latest Snapdragon for S2 will the kernel be included in the package? I still cant pass the logo screen even though I have flashed different kernels
Click to expand...
Click to collapse
the kernel is included most all roms doe and also make sure you follow all instructions on flashing properly... always make sure you do a backup )
gl
slimlo said:
the kernel is included most all roms doe and also make sure you follow all instructions on flashing properly... always make sure you do a backup )
gl
Click to expand...
Click to collapse
Thanks Sir Slim, I will try to flash the Snapdragon ROM as soon as after I finish downloading it. Because I believe I have cleared out the operating system and other important data on my device, that's why I need a new ROM.
Hi mate,
Do you run a stock ROM on your phone like you didnt flash any custom ROM on it....
Did you check if the SIYAH kernel you flashed on your device has STOCK ROM support, cause if the siya kernel you flashed has no support for stock rom it will just stay on the siyah logo the whole day until it drains out your battery.....
if you want to go to this website : http://dorimanx.shine.sk/ and dowload the v8.xxx those got stock rom support..... then do a wipe data factory reset....
if your phone booted up, and want to you wipe the phone completely, go to settings and do a factory reset there, your phone will prompt you if you want to wipe the memory card too.... put a check on it then follow the steps okay....
[email protected] said:
Hi mate,
Do you run a stock ROM on your phone like you didnt flash any custom ROM on it....
Did you check if the SIYAH kernel you flashed on your device has STOCK ROM support, cause if the siya kernel you flashed has no support for stock rom it will just stay on the siyah logo the whole day until it drains out your battery.....
if you want to go to this website : http://dorimanx.shine.sk/ and dowload the v8.xxx those got stock rom support..... then do a wipe data factory reset....
if your phone booted up, and want to you wipe the phone completely, go to settings and do a factory reset there, your phone will prompt you if you want to wipe the memory card too.... put a check on it then follow the steps okay....
Click to expand...
Click to collapse
Thank you sir! You are right that I did not have a custom ROM when I installed the Siyah kernel. Maybe that's the reason I was stuck
Newbees said:
Thank you sir! You are right that I did not have a custom ROM when I installed the Siyah kernel. Maybe that's the reason I was stuck
Click to expand...
Click to collapse
Nope it's not the right reasons may be you flashed a wrong siyah kernel.
Tell me your android version is it jellybean or ics
Sent from my GT-I9100 using xda premium
My SamSung S2 up rom Stock 4.1.2 via odin or cook rom base 4.1.2 via CMW is bootlooped logo S2 I wipped all before and after uprom. And i up 2.3.6 or 4.0.3 or stock rom > 4.2 is not bootloop. i want up Wanna lite 4.1.2 rom, how to fix bootloop? Thanks you very much, sorry for my bad english.
P/S: When i change Mobile Networks to GSM only is Not Service, i can call when change Mobile Networks to 3G with poor network.i tried modems.
Flash Philz kernel first. Reboot in Recovery and flash Wanam Lite.
PS: what is 'up'?
Donnie Sins said:
Flash Philz kernel first. Reboot in Recovery and flash Wanam Lite.
PS: what is 'up'?
Click to expand...
Click to collapse
Yes, it is still boot loop, i flash form Wannalite 4.0.3 via Philz to Wannalite base 4.1.2, Stock rom 4.1.2 also bootloop.
You can try to do a full wipe, install Wanam (not Wanna) Lite.
Then reboot into Recovery, flash Philz kernel and reboot system.
Did you try to flash another custom rom by the way?
Donnie Sins said:
You can try to do a full wipe, install Wanam (not Wanna) Lite.
Then reboot into Recovery, flash Philz kernel and reboot system.
Did you try to flash another custom rom by the way?
Click to expand...
Click to collapse
Yes, i flashed stock 4.0.3, many Custom rom 4.2 or 4.3 it ok. but when i flash custom rom base 4.1.2 is bootloop even stock 4.1.2 still boot loop.
I Flash stock 4.0.3 -> Flashed Kernel Philz -> Do Wipe -> FLash Custom rom base 4.1.2 -> Do Wipe -> Bootloop
Tinhte1989 said:
I Flash stock 4.0.3 -> Flashed Kernel Philz -> Do Wipe -> FLash Custom rom base 4.1.2 -> Do Wipe -> Bootloop
Click to expand...
Click to collapse
After flashing a rom, you shouldn't do another wipe. In that case you erase the rom you've just flashed, and there is nothing to boot up.
Donnie Sins said:
After flashing a rom, you shouldn't do another wipe. In that case you erase the rom you've just flashed, and there is nothing to boot up.
Click to expand...
Click to collapse
It still bootloop. i did not wipe after flashed
blueforever89 said:
It still bootloop. i did not wipe after flashed
Click to expand...
Click to collapse
Last thing that comes up in my mind is: flash the rom. After it, reboot into Recovery, DON'T wipe and reflash the rom, reboot.
Not really sure if this is making any difference, but maybe it is
Edit: I just saw you're a different person.. What's up with that?
Donnie Sins said:
Last thing that comes up in my mind is: flash the rom. After it, reboot into Recovery, DON'T wipe and reflash the rom, reboot.
Not really sure if this is making any difference, but maybe it is
Edit: I just saw you're a different person.. What's up with that?
Click to expand...
Click to collapse
i tried, not solve !
1 account log from gmail, 1 account xda :fingers-crossed:
blueforever89 said:
i tried, not solve !
1 account log from gmail, 1 account xda :fingers-crossed:
Click to expand...
Click to collapse
Sorry, I've no idea... Good luck anyway:thumbup:
Donnie Sins said:
Sorry, I've no idea... Good luck anyway:thumbup:
Click to expand...
Click to collapse
i don't know why i can't Flash rom base 4.1.2 JB!
Thanks for your help!
Any idea? Please Help me,
Redownload everything again... then check md5 sum if its correct..if its a mismatch it will be a bootloop
Then flash latest philz in download mode
Go to cwm
Wipe data
Wipe dalvik
Wipe cache
Flash neat rom (juzt a suggestion to use a rom wid preload content)
Reboot...
doctor_droid said:
Redownload everything again... then check md5 sum if its correct..if its a mismatch it will be a bootloop
Then flash latest philz in download mode
Go to cwm
Wipe data
Wipe dalvik
Wipe cache
Flash neat rom (juzt a suggestion to use a rom wid preload content)
Reboot...
Click to expand...
Click to collapse
I flashed I9100XWLSW_NeatROM_Lite_v4.8.zip rom with Same MD5 Sum. But not getting out Bootloop Android Neatrom, i tried many stock 4.1.2, or cook like wamma lite, Neat base 4.1.2. all is getting bootloop. Other rom not Base 4.1.2 is ok. I can't understand.
Have Any Idead?
Help Needed !!
Recently I unrooted my alerady rooted I9100 and installed stock ROM,after few days again I rooted it and installed
custom ROM but now whenever I go to install stock base ROM like S4 for I9100 , NoteII mini etc...
it gets stuck on the samsung logo (earlier they were working ok), but this doesnt happen with other ROM's like CM,Carbon etc...
Can anyone suggest any solution or what I must have done wrong.
Thanks in Advance
abhiwildfire said:
Help Needed !!
Recently I unrooted my alerady rooted I9100 and installed stock ROM,after few days again I rooted it and installed
custom ROM but now whenever I go to install stock base ROM like S4 for I9100 , NoteII mini etc...
it gets stuck on the samsung logo (earlier they were working ok), but this doesnt happen with other ROM's like CM,Carbon etc...
Can anyone suggest any solution or what I must have done wrong.
Thanks in Advance
Click to expand...
Click to collapse
Always do Wipe data Factory restore and wipe cache before going to Stock rom to Cm10 or any custom rom.
Jeetu said:
Always do Wipe data Factory restore and wipe cache before going to Stock rom to Cm10 or any custom rom.
Click to expand...
Click to collapse
Yep I also did format/system along with the wipes but no luck is it due to recent changes to cwm's like when I was on stock I had rooted with Philz (touch) and then when I tried to install other stock base I was on other CWM (non touch)
basically I am very new in this flashing world...
abhiwildfire said:
Yep I also did format/system along with the wipes but no luck is it due to recent changes to cwm's like when I was on stock I had rooted with Philz (touch) and then when I tried to install other stock base I was on other CWM (non touch)
basically I am very new in this flashing world...
Click to expand...
Click to collapse
have the latest cwm installed and wipe data, cache and dalvik cache before flashing an entirely new rom
No certainly cwm has nothin to do with it
Check for corupt file