Hi,
TL;DR version below.
Note: This is just a traceback that may help diagnose the problem.
I "own" an Ace (S5830M, everything from i/C works fine). I was playing around with some custom ROMs and evertything was going pretty fine. I installed Jelly Blast (OTA 3) and flashed back to stock a few times, everything was fine and working. Used the recovery/backup functionality from CWM (5.0) to switch between the mentioned installations and it was all good.
Here start the real problem:
During one of the instalation of the custom ROM i went to Advanced -> Format /system (Because probably I miss read the instructions). After this the phone booted and didn't bootlooped, instead it just showed the initial logo (white letters, phone model. Not Samsung animation). As I noted it was stuck I flashed stock from Odin and got it working back.
Everything is fine, the phone works as intended, exept that it "can't" use the baseband I was using before (850 MHz frequency, 3G). I say "can't" because after n tries I was able to send 1 SMS, and only one. All the others failed. And on really unusual occasions I get signal and the phone tells me the provider (Kolbi/ICE) but after a few seconds it loses the connection/signal.
What I've tried so far:
Go to Settings->Wireless Connections->Movile Networks:
There I tried to choose my carrier, but isn't listed 99% the time. The other two are(Claro/movistar). So I set it to automatic.
Check IMEI:
It is the right one
Try to restore from a previous working state with CWM:
I can't it says that there's a MD5 missmatch. (Can I force it?)
Flash a Modem file that is known to work (With another, same model, phone and carrier)
Same sympthoms: does not work.
Dial *#197328640# and play with the settings:
Here I setted to: Type: DUAL_MODE_UMTS_PREF
Band: AUTO
These are the same settings that the working phone.
Flash the stock carrier-branded firmware.
Without luck so far.
====================================================
TL;DR
I have two phones, same model and same carrier. One does not detect the 850MHz band (3G to GMS) so I get no service 99.99% the time, but I was able to send a single SMS. All this after formating /system via CWM.
I've tried to use the same setup and setting from the working phone without success.
Any help or hint would be greatly appreciated.
Footnote: English is not my native language, please understand if I confused some of the tech terms even if IT is my field.
niant said:
Hi,
TL;DR version below.
Note: This is just a traceback that may help diagnose the problem.
I "own" an Ace (S5830M, everything from i/C works fine). I was playing around with some custom ROMs and evertything was going pretty fine. I installed Jelly Blast (OTA 3) and flashed back to stock a few times, everything was fine and working. Used the recovery/backup functionality from CWM (5.0) to switch between the mentioned installations and it was all good.
Here start the real problem:
During one of the instalation of the custom ROM i went to Advanced -> Format /system (Because probably I miss read the instructions). After this the phone booted and didn't bootlooped, instead it just showed the initial logo (white letters, phone model. Not Samsung animation). As I noted it was stuck I flashed stock from Odin and got it working back.
Everything is fine, the phone works as intended, exept that it "can't" use the baseband I was using before (850 MHz frequency, 3G). I say "can't" because after n tries I was able to send 1 SMS, and only one. All the others failed. And on really unusual occasions I get signal and the phone tells me the provider (Kolbi/ICE) but after a few seconds it loses the connection/signal.
What I've tried so far:
Go to Settings->Wireless Connections->Movile Networks:
There I tried to choose my carrier, but isn't listed 99% the time. The other two are(Claro/movistar). So I set it to automatic.
Check IMEI:
It is the right one
Try to restore from a previous working state with CWM:
I can't it says that there's a MD5 missmatch. (Can I force it?)
Flash a Modem file that is known to work (With another, same model, phone and carrier)
Same sympthoms: does not work.
Dial *#197328640# and play with the settings:
Here I setted to: Type: DUAL_MODE_UMTS_PREF
Band: AUTO
These are the same settings that the working phone.
Flash the stock carrier-branded firmware.
Without luck so far.
====================================================
TL;DR
I have two phones, same model and same carrier. One does not detect the 850MHz band (3G to GMS) so I get no service 99.99% the time, but I was able to send a single SMS. All this after formating /system via CWM.
I've tried to use the same setup and setting from the working phone without success.
Any help or hint would be greatly appreciated.
Footnote: English is not my native language, please understand if I confused some of the tech terms even if IT is my field.
Click to expand...
Click to collapse
Flash a new rom and kernel
Rahul4Ace said:
Flash a new rom and kernel
Click to expand...
Click to collapse
Yeah, that could fix it. BTW, was there any need to quote the whole OP?
Related
Hi.
I have a big problem with my G2, and have tried many things.
It all started 2 weeks ago. I lost connection to my network.
I tried many things, and ended up giving it to a repair shop, in China, as I was there shortly. They put a new firmware into the phone, and a chinese SIM card worked.
I found an english version of the firmware, and asked them to update with that version, No problem. Everything worked well...but when I arrived back to Denmark, same problem. Not registered on the network.
Now I have tried many things, as Kies could not recognize the firmware version. I burned a 2.35 version into the phone with Odin, and Kies regocnized the version, and now updated to 4.03. Great, but ... I have the same problem. APN settings acc to my network provider. Oister 3 in Denmark.
I really have no idea what to do anymore. And I cant send it in for repair, as the flash counter says 10 times.
Is ther someone here, with a very deep knowledge in Logs etc, as I can send Logs if I am explained what to do.
The short time the phone worked, did I really love it.
And also the chinese SIM can not connect from Denmark.
I would prefer all Logs etc in private email, but if we solve it, I will poste solutions and results here.
Best of regrads
Morten
As for the counter, install and run triangleaway - it can be found in the SGSII section of XDA.
Check that the sim card works (try it on another phone) and borrow another sim card (on the same network). It is amazing how many problems like this are due to a damaged sim card or just not connecting correctly. I had a friend who took the sim card out to flash their Samsung Galaxy 3 and put in the sim card wrongly and couldn't make a call.
Can you copy your contacts to or create one in the sim card?
I doubt that it is a problem with the EFS folder, ie no IMEI number because it was fixed with a china sim, but it may be. Is the IMEI number you get from dialing *#06# 004999010640000 or different from the label under the battery? If so then you have a EFS folder problem. There is an app that may fix it - it requires root - * HERE *
Mobile network
Hi
Thanks for the reply.
A:
I can make, copy, edit etc contact directly at the simcard in the phone, and also copy, edit etc from Kies to the Sim card. And yes. It is the simcard I can do those things at. Double checked that it was somcard and not the phone memory
B:
Double checked the IMEI number again.
Label phone same as *#06#
Further information:
In the first day, I tried many many things to get the phone working.
I searched the internet a lot, and I found some kind of help. Like with IMEI check, I should type a code like *#xxxx# or *xxxx* Stupid as I was, I did not write down the code, and also did not safe the page on the internet, so I have no idea what code I wrote. I am sure it was something regarding Mobile network or CSC.
Reg Triangle away.
My phone is no longer rooted, as I try to have it in original mode, so its ready to send to repair, if needed. Triangleaway needs the phone to be routed, right ?
And will that not require an unsafe kernel ?
After resetting, then I suppose I need to install an original kernel again, and will that not make the counter go to 1 ?
Any other ideas ?
Regards
Morten
can you be little clear....
no network or no data (internet) on your current network
1: do you have a locked phone or unlocked. [carrier locked when new]
2: no network will be no signals at all, no phone call....
3: no data will be you cant browse, send receve emails
4: counter can be fixed easy as now your on ics
Hi,
I got the same problem but different scenario
atifsh said:
can you be little clear....
no network or no data (internet) on your current network
1: do you have a locked phone or unlocked. [carrier locked when new]
2: no network will be no signals at all, no phone call....
3: no data will be you cant browse, send receve emails
4: counter can be fixed easy as now your on ics
Click to expand...
Click to collapse
1. my phone is unlocked(international).
2. signal show full, but no phone call
3. I don't use data, but wifi, and no problem with wifi.
Well, this : not registered on network only happen if phone idle for more than 3hrs, meaning phone just work normally if I don't let it idle for long time. This very frustrating as every morning after wake up I have to switch between airplane mode for phone working again.
Greatly appreciated for your help
Thanks in advance
P/s: currently on Slim rom(cm9). But have tried almost all custom rom found in xda, problem still exist. Even try to change CSC to my current country( Thailand) on stock DL7( included Thailand region), no luck. APN setting also change to default network provider.
Mobile network problem
Hi.
Please see my answers below
1: do you have a locked phone or unlocked. [carrier locked when new]
The phone worked before, and was not locked, but as I send a command to the phone, could I have locked it ? How can I check that ? And it does not give me any warning when I start the phone up.
When I try to make a call, it right away says: Dialling ...Call ended.
2: no network will be no signals at all, no phone call....
No mobile network. It is ONLY a problem with phone calls and reciving calls.
I have plenty of signal
3: no data will be you cant browse, send receve emails
Data is right now not working, WiFi works.
I cant get correct APN settings, as my provider sends this as system configuration to the phone, but cant recive it.
3A: My provided is named 3 Oister, and normally this provider is listed under Network operators. On this phone it is NOT listed. 3 Oister is using network of 3, and only network of 3 is listed.
If I pull down the menu from the topbar on the phone, it actually says 3 Oister, but 3 Oister is not listed under Network Operators.
On my other SG2, 3 Oister is listed in Topbar and under Network Operators.
I bought a new SG2 as well, and we are 2 persons using SG2 here.
4: counter can be fixed easy as now your on ics
How ? Can I do that without rooting and install different firmware ?
I do run ICS ver 4.03, updated by Kies.
In worst case, I will send the phone in for repair, but for sure, needs the counter reset.
Regards
Morten
Put a new firmware in the phone then probably wrong modem and CSC for your location .
Chinese sim unlikely to work 4000 miles away but that is easy to swap sim .
Rom counter for ICS use the search tool for the relevant post .
jje
Mobile network problem
Hi
Please find answers below:
Put a new firmware in the phone then probably wrong modem and CSC for your location .
As my counter says 10, you can see, I have tried this several times, and its also written in my first post.
Please send the code for check of CSC and changing CSC. As I remember it is set to be NEE.
Chinese sim unlikely to work 4000 miles away but that is easy to swap sim .
Chinese SIM works all over the world, as long as Roaming is allowed. And it works in the other phone. Now I have the Denmark SIM in, and same problem. Yes, I did close down the phone, changed SIM and started the phone again. Exactly SAME problem.
Rom counter for ICS use the search tool for the relevant post .
Would be nice to have the info written here instead.
regards
Morten
SG2Denmark said:
Hi
Please find answers below:
Put a new firmware in the phone then probably wrong modem and CSC for your location .
As my counter says 10, you can see, I have tried this several times, and its also written in my first post.
Please send the code for check of CSC and changing CSC. As I remember it is set to be NEE.
Chinese sim unlikely to work 4000 miles away but that is easy to swap sim .
Chinese SIM works all over the world, as long as Roaming is allowed. And it works in the other phone. Now I have the Denmark SIM in, and same problem. Yes, I did close down the phone, changed SIM and started the phone again. Exactly SAME problem.
Sim CSC Modem . Firmware .
Then your answer is hardware fault if above are ruled out as not a problem.
Rom counter for ICS use the search tool for the relevant post .
Would be nice to have the info written here instead.
Sorry i refuse point blank to search for someone else .
Neither do i have the relevant post bookmarked otherwise it would have been posted .
jje
Click to expand...
Click to collapse
SG2Denmark said:
Hi.
Please see my answers below
Regards
Morten
Click to expand...
Click to collapse
try this before you send for repair.......
get this stock for your network
http://www.hotfile.com/dl/149692036/21dfd27/I9100XXLPQ_I9100HTDLP3_HTD.zip.html
1: forget all your idea's do exact as i say
2: remove your sdcard
3: using cwm format system, cache, data, sdcard [system is a must]
4: remove battery / insert back goto download mode
5: flash the ROM you downloded using odin, after restart dont do any restores
6: wait for few minutes now dial this *2767*3855# [important]
dont restore any backups including titanium stuff.
if your phone works now put your sdcard back and do whatever now you want.
---------- Post added at 04:29 PM ---------- Previous post was at 04:24 PM ----------
Saisuay said:
Hi,
I got the same problem but different scenario
1. my phone is unlocked(international).
2. signal show full, but no phone call
3. I don't use data, but wifi, and no problem with wifi.
Well, this : not registered on network only happen if phone idle for more than 3hrs, meaning phone just work normally if I don't let it idle for long time. This very frustrating as every morning after wake up I have to switch between airplane mode for phone working again.
Greatly appreciated for your help
Thanks in advance
P/s: currently on Slim rom(cm9). But have tried almost all custom rom found in xda, problem still exist. Even try to change CSC to my current country( Thailand) on stock DL7( included Thailand region), no luck. APN setting also change to default network provider.
Click to expand...
Click to collapse
next time start your own thread........ this time im helping
do as i posted for the OP but instead of his firmware download your country specific firmware.
seems as a modem issue but can be sim related.
Mobile network problem
Hi again
Followed the guide very detailed
3: using cwm format system, cache, data, sdcard [system is a must]
Wiped all data in System and also Wiped Cache, using:
Root the Samsung Galaxy S2 GT-I9100 running XXLPQ firmware and install ClockworkMod Recovery: CF-Root-SGS2_XX_XEO_LPQ-v5.3-CWM5.tar
Done with Super User Granted.
4: remove battery / insert back goto download mode
Done
5: flash the ROM you downloded using odin, after restart dont do any restores
Flashed with Odin 1.85 in PDA: I9100XXLPQ_I9100HTDLP3_I9100NELP2_HOME.tar.md5
6: wait for few minutes now dial this *2767*3855# [important]
Done. Phone shows Factory Reset in big letters
dont restore any backups including titanium stuff.
Nothing restored.
Booted up, and automatic installed APK's
Same problem.
Only difference is that now the counter says 11 counts
But thanks for a detailed and well told possibility.
As I see it, the problem is connected to the standard the phone connects to the Mobile grid. As I told earlier, I made a stupid thing. I send a command with *#xxxx* in the phone, and I cant remember what code, and I did not save the page on the internet. I really think the problem is about a standard. That the phone is setup to a standard that the 3G net is not using in Denmark.
I can dump logs etc, if anyone can help. But I need to know how.
Regards
Morten
buddy your problem was.... network right? is it working now?
forget counter it will be fixed....later using triangle away with ics bootloader
---------- Post added at 12:06 AM ---------- Previous post was at 12:01 AM ----------
if your phone now works fine with calls send and recieve, manually add the apn to get 3G.
Mobile network problem
Hi
Nope. Did not solve the problem.
Just ran Triangle away, and moved the Firmware: I9100XXLPQ_I9100HTDLP3_I9100NELP2_HOME.tar.md5 to the SD card.
Will try now to install it by CWM
And then I give up. Will try to send it for repair ..... really a shame, as I really would have liked to solve it here
Cheers
Morten
Mobile network problem
Hi Buddy
It finds a lot of Networks, but cant connect to any of them
3 networks with 3G and 4 with 2 G
But not the Mobile network I need to connect to> Oister 3
My other SG2 finds that network without any problem
Cheers
Morten
I had the same problem too. At first I tought it was a rom issue, but it wasn't actually. I turned my phone off and removed and placed back my sim card and it worked.
Mobile network problem
Finished programming original firmware using CMW as source for Odin, after counter was reset to 0, and the pnone status is the same as before, but counter is 0.
So will try to send it in for repair.
Thanks to u all.
And SIM card has been removed several times, even tried with a different.
No luck at all
Cheers, and thanks again
Morten
Did you ever get to the bottom of this?
I've been using my phone in Brazil and now i'm in the UK, it's doing exactly as you describe.
...
How would you go about checking these?
Escy said:
How would you go about checking these?
Click to expand...
Click to collapse
Compare the IMEI that displays when you type *#06# to the IMEI printed on the label under your battery. They should be the same.
For your own sake, do NOT post what the IMEI under the battery actually is, whether it's the same as what's displayed when you dial *#06# or not.
As for checking IMEI blocking by the carrier, that should be obvious. Call your carrier.
Need some expert here for help before I use ODIN to restore the factory firmware package.
Currently have G925W8 (Canadian Rogers) and currently running Int 5.1.1 rom on it. All of sudden my phone can't make or receive phone calls. I mean when I tried to make the phone call, it just ends right away, and no one can call in to my phone number either and goes to VM directly.
I tried different kernel (Arter/Hacker/UniKernel) and different rom combination...Still no GO...
I tried to apply Mr.X Audio Patch too (not sure how many patches are there, but I only download the one for Mr.X audio patch for 920T) and it doesn't work either.
I know in G925W8 forums talk about different BL/Modem, different combination and no go either.
Please note my phone works perfectly and I can get the internet connection (LTE) but just can't make the phone call. Even now I won't use the phone much but still need to have the phone work.
I think the major issue is when I am in the phone, go to call settings -> More Settings that give me an error "Failed to Read data Network or Sim card error".. I though it's my sim card, but i plugged it in my 1+1 and have no issue making/receiving calls..
Anyone that have any idea?!?
calling in out
had the same problem, in my case i installed an original samsung 5.1.1 and a kernel to root the phone, i got the same as you, everything worked but the phone.
only way to get out, is download from samsung firmware repository or sam mobile the EXACT ROM FOR YOU MODEL AND CARRIER (i cannot emphasize enough the CARRIER) believe it or not if you want to install an original rom you must respect the carrier for a custom rom it's something else altogether
in your case you odin with the rom of you phone/carrier IF IT WORKS (NOT ROOTED) I mean ccalling in/out, then install a different kernel in order to root.
if it works then your previous kernel (as was in my case) was the culprit
good luck
the carrier is where you bought the phone or the cell co affiliated to the store where you bought the phone, there's ALWAYS a link from "A" carrier in your phone
Elin28 said:
Need some expert here for help before I use ODIN to restore the factory firmware package.
Currently have G925W8 (Canadian Rogers) and currently running Int 5.1.1 rom on it. All of sudden my phone can't make or receive phone calls. I mean when I tried to make the phone call, it just ends right away, and no one can call in to my phone number either and goes to VM directly.
I tried different kernel (Arter/Hacker/UniKernel) and different rom combination...Still no GO...
I tried to apply Mr.X Audio Patch too (not sure how many patches are there, but I only download the one for Mr.X audio patch for 920T) and it doesn't work either.
I know in G925W8 forums talk about different BL/Modem, different combination and no go either.
Please note my phone works perfectly and I can get the internet connection (LTE) but just can't make the phone call. Even now I won't use the phone much but still need to have the phone work.
I think the major issue is when I am in the phone, go to call settings -> More Settings that give me an error "Failed to Read data Network or Sim card error".. I though it's my sim card, but i plugged it in my 1+1 and have no issue making/receiving calls..
Anyone that have any idea?!?
Click to expand...
Click to collapse
So by a stupid mistake I have selected in *#*#4636#*#* the Radio Band to USA. The signal suddenly dropped and it stopped working at all, the nework does not connect except in 4G and only for data. Calls and text are not working, only 4G data works fine. This is on the sim1 though. On sim2 all is ok (except that with the X829 ROM, on sim2 I have no data, and on sim1 I have no calls )) ). I was on sim1 when I've changed the Radio Band, so I guess that only this one got affected since sim2 is working properly.
Is there any Radio Band files that I can restore? Or some app that can restore the settings of the modem?
Any help is highly appreciated.
PS: Reinstalling the ROM (clean or dirty) doesn't help. Factory resetting also doesn't help. I would downgrade to 014s but I'm afraid not to end up with a brick.
Change the rom
valy_cta said:
So by a stupid mistake I have selected in *#*#4636#*#* the Radio Band to USA. The signal suddenly dropped and it stopped working at all, the nework does not connect except in 4G and only for data. Calls and text are not working, only 4G data works fine. This is on the sim1 though. On sim2 all is ok (except that with the X829 ROM, on sim2 I have no data, and on sim1 I have no calls )) ). I was on sim1 when I've changed the Radio Band, so I guess that only this one got affected since sim2 is working properly.
Is there any Radio Band files that I can restore? Or some app that can restore the settings of the modem?
Any help is highly appreciated.
PS: Reinstalling the ROM (clean or dirty) doesn't help. Factory resetting also doesn't help. I would downgrade to 014s but I'm afraid not to end up with a brick.
Click to expand...
Click to collapse
If i were you. I would change the rom from china to indian rom. It would help you. The radio band of chinese rom and the indian rom is different. It would replace the radio band of chinese rom and if it doesn't work. Then return to the chinese rom
I'm 100% sure it would help you.
valy_cta said:
So by a stupid mistake I have selected in *#*#4636#*#* the Radio Band to USA. The signal suddenly dropped and it stopped working at all, the nework does not connect except in 4G and only for data. Calls and text are not working, only 4G data works fine. This is on the sim1 though. On sim2 all is ok (except that with the X829 ROM, on sim2 I have no data, and on sim1 I have no calls )) ). I was on sim1 when I've changed the Radio Band, so I guess that only this one got affected since sim2 is working properly.
Is there any Radio Band files that I can restore? Or some app that can restore the settings of the modem?
Any help is highly appreciated.
PS: Reinstalling the ROM (clean or dirty) doesn't help. Factory resetting also doesn't help. I would downgrade to 014s but I'm afraid not to end up with a brick.
Click to expand...
Click to collapse
I did the same thing by my mistake.And my le max 2 also became not able to connect internet. In my case, it can't connect both 4G and 3G .
But I fixed it. But I don't know that it get back to the original completely.
I'm japanese.And I'm sorry for that my English skil is very poor.
My current rom is Le2_X820-MAX_ROW-5.8.015S_V29_CUOCO92.
I used DFS CDMA TOOL and checked the items on the "Band Preferred" same as "RF BC Config".
1. download HTC Diag Driver. You have to customize .inf file later.
2. conect device to your windows pc and choose MTP and USB Debugging.
3. enter the follows command.
"adb shell"
"su"
"setprop sys.usb.config diag,adb"
When you enter this command, your device change over diag mode.
4. diag driver install.
You have to find hardwawer ID from device manager.
And replace the hardware ID in .inf file.
5. If you install diag driver correctly, you will be able to use DFS CDMA TOOL.
sorry, I can't explain any more..English is difficult...
I bought my phone from china and I'm in US, and it works perfect on stock with LTE enabled for AT&T by default. Might I ask why did you change it to US band and it stopped working? It would still work right?
Ootp said:
If i were you. I would change the rom from china to indian rom. It would help you. The radio band of chinese rom and the indian rom is different. It would replace the radio band of chinese rom and if it doesn't work. Then return to the chinese rom
I'm 100% sure it would help you.
Click to expand...
Click to collapse
Many thanks for the advice but it didn't help. I had installed the indian rom and then to the chinese without any change in the behavior of the modem. I'll try the chatmonchy's advice to see if there will be any improvement.
xterminater07 said:
I bought my phone from china and I'm in US, and it works perfect on stock with LTE enabled for AT&T by default. Might I ask why did you change it to US band and it stopped working? It would still work right?
Click to expand...
Click to collapse
Actually I'm in Europe and looks like we use slightly different bands (??). I get 4G data but without calls. To other networks like 2G and 3G it connects sometimes but it's for few seconds only. I even don't remember what made me change the bands to USA, I guess I was curios what settings those were. The options are "USA band" and "Band 6", neither one is working well for my device. And strangely though, there is no other option to go back like "Auto" or something. It seems that I'm not the only one that did it. After a google search, it turned out that a lot of people had the same issue. For some, the factory reset helped, for others was flashing via TWRP the radio bands again.
I had solved the issue and I will post a guide later on for those who want to unlock additional bands or did the same mistake as I did.
Thanks for the help guys.
valy_cta said:
I had solved the issue and I will post a guide later on for those who want to unlock additional bands or did the same mistake as I did.
Thanks for the help guys.
Click to expand...
Click to collapse
That's good!!
I'm looking forward to your guide about unlock additional bands.
thread: [SOLVED] Accidentally changed the Radio Band to USA
Hi, gyus
I had the same problem, i select USA band and everything went wrong,
The simplest way for me was:
installing "X820 LeMax2 RevolutioN_Team Resurrection Remix", no other from TeamSpain, only Resurrection Remix
http://revolutionlemax2.blogspot.al/
https://mega.nz/#!T9o0wAhJ!iLa9mrPAr...VkCg3_L-q2RgnA
then after installation, go in dialer and call *#*#4636#*#*.
There are three band: Automaic, USA, and EURO.
I select the EURO and everything i'ts OK.
BEFORE DO ACTIONS DON'T FORGET TO BACKUP ALL THE ROM WHERE YOU ARE WITH TWRP
readion said:
Hi, gyus
I had the same problem, i select USA band and everything went wrong,
The simplest way for me was:
installing "X820 LeMax2 RevolutioN_Team Resurrection Remix", no other from TeamSpain, only Resurrection Remix
http://revolutionlemax2.blogspot.al/
https://mega.nz/#!T9o0wAhJ!iLa9mrPAr...VkCg3_L-q2RgnA
then after installation, go in dialer and call *#*#4636#*#*.
There are three band: Automaic, USA, and EURO.
I select the EURO and everything i'ts OK.
BEFORE DO ACTIONS DON'T FORGET TO BACKUP ALL THE ROM WHERE YOU ARE WITH TWRP
Click to expand...
Click to collapse
Hi, how to install this ROM? Which TRWP I need? I install with official TWRP, but bootlop after instalation.
Try this link for recovery by GrossoShop Couco92
https://www.androidfilehost.com/?w=files&flid=57913
---------- Post added at 02:35 PM ---------- Previous post was at 02:33 PM ----------
karellang said:
Hi, how to install this ROM? Which TRWP I need? I install with official TWRP, but bootlop after instalation.
Click to expand...
Click to collapse
Try this link for recovery by GrossoShop Couco92
https://www.androidfilehost.com/?w=files&flid=57913
Does not help. If I go to servise menu (dial *#*#4636#*#*) , I see Radio turned OFF and I can´t change it. How to solve this ?
Did you post any guide how you solved the issue?
Unfortunately USA band selected
Hi,
I live in India. I bought Oppo F3 Plus (CPH1613) 4Gb Ram, 64GB Storage, Qualcomm MSM8976 Pro Snapdragon 653 a year ago and was working too much fine. I was wondering about Qualcomm mobile secret codes and found this *#*#4636#*#* . I dialed this and accidentally changed radio band to USA band and suddnly on instant my mobile didn't get any network signal. From then, I went for Oppo care, and mobile repairing shops and self tried and tested for lots of time; but everyone unable to bring phone to normal. I reset my mobile, flashed stock rom for countless times, wiped all data but nothing helped me out. Finally i rooted my oppo f3 plus and tried to boot in fastboot mode; but Oppo removed bootloader and fastboot mode from 2016 (as posted in XDA). I got a little link about resetting USA band to automate and is erasing modemst1 and modemst2. But again it have to be performed from fastboot.
Help me out for my mobile.
You can flash a modem file, it will reset it as well. Changing the ROM won't update the modem configuration. Try to search modem files and flash them via TWRP.
Hi all!
I bought an S6 Edge second hand and after flashing a stock ROM, I had the "emergency only" calls issue, I tried everything I could find in the forums to no avail and I ended up taking it to a repair service. I did not think they could fix it but they did and I would like to know what they did to it in order to prevent it from happening again and to know if I can leave it as default (not custom OS) so that it can upgrade.
State of phone when bought:
So, the phone was working well with all carriers (from Colombia). The only thing I was able to notice after I bought it was that it was still on Marshmallow (6.0.1) with carrier branded stuff. It was in perfect shape otherwise.
So I downloaded a stock ROM and installed it using Odin. After this the phone would not let me make calls as it was not registering on the network. It did not even let me make emergency calls despite getting full bars of signal and being able to recognise the list of carriers when attempting to manually connect to them.
Important: The ROM downloaded was for the right version of the phone which was the G925i and the IMEI, serial number and baseband were not altered from the original. Also, I checked the phone to see if it was reported as lost/stolen and it was not (of this I'm sure because in Colombia you can consult a centralised database on any carrier's webpage). Also.. Here in Colombia it is illegal for carriers to lock phones.
Steps I took to fix it:
Downloaded ROMs for all carriers, branded and unbranded, I even installed one from Trinidad and Tobago and a LATAM one.
I performed all the tricks to disable and enable flight mode, location services, try con connect manually to the networks, changing to GSM only, GMS/CDMA, international roaming, etc.
I also extracted modem.bin from an earlier version and flashed the modem.bin with Odin (6.0.1 moden on 7.0, 5.1.1 moden on 6.0.1 and 5.1.1 moden on 7.0). All modems flashed correctly and the issue remained exactly the same.
So I finally gave up.. I installed the latest stock ROM which was an unbranded Nougat (7.0) version and took it to a repair service and they fixed it in a couple hours.
What I noticed after the phone was "repaired":
- The phone was rooted, SuperSu was installed, no other root app was installed.
- On SuperSu, there are entries for ADB shell (they all say Superuser command contents have not been logged for this entry) in a two minute timespan.
- The android version was downgraded to 6.0.1, I was told not to try to update it.
- Developer options was enabled with USB debugging turned on.
- The boot option (the one where you can wipe data and cache partition) was left as original (not the TWRP one).
- The ROM used to downgrade was the same I had before but only downgraded the version.
I suspect this same procedure was performed before on the phone but it had the original ROM carrier branded so it seems as if they installed a custom ROM, rooted it, connected with pc and performed some command line stuff to fix it, then cleaned the bootloader to a stock one.
The questions:
Any ideas what did the repairman do to fix the phone? Also, would it be safe to make a full backup with TWRP and flash again a stock ROM upgraded to 7.0 and then flash the backed up modem to get it working? Or would that possibly screw up the repair?
Thank you all in advance for any help. I'm sure there are lots of people out there experiencing the same "emergency only" issue I had but there does not seem to be a fix around, but clearly there is one! So I hope this sheds some light into what could possibly happen.
Hi, I downloaded and installed Lineage ROM, everything was working fine but I found that I was not able to send text messages (receiving messages was okay), I tried change values under test menu (*#*#4636#*#*) but problem persist.
I tried clean installation of new ROM (Aosp).
I tried install new firmware from:
https://forum.xda-developers.com/re.../firmware-xiaomi-redmi-note-5-5-plus-t3759683
And baseband from :
https://androidfilehost.com/?fid=746163614322262750
And finally, text messages are OK, unfortunately I am not able connect to 4G/ LTE networks now. Only 2G and 3G networks are working. LTE services were working without problem on original Miui and Lineage ROM.
Can someone try help me how solve it ? I would really appreciate any ideas.
Do you think this can help?
https://androidfilebox.com/app/redmi-5-plus-modem-firmware/
Thanks in advance and happy weekend
i have the same question! +1
I tried fresh install original MIUI ROM, but it did not help
http://en.miui.com/getrom-340.html?m=yes&mobile=2 .
LTE is not available still.
I did not try this method still: https://androidfilebox.com/app/redmi-5-plus-modem-firmware/
But I don't have another option I guess.
With LTE no Problems = https://forum.xda-developers.com/redmi-note-5/development/rom-omnirom-t3823189
Unfortunately LTE is not working on this ROM (Omni) for me too, but I expected it, because as I wrote I tried original MIUI as well. It's problem of wrong firmware, baseband, modem or something, because hard reset or flashing new rom don't fix it. Btw, this morning I was in big city in my country and my phone was able connect to LTE, but it was 1800 or 2100 MHz, which are available only in bigger cities. When I came back to home, it showing only H+ again. It seems my phone is not able to connect only to LTE on 800 MHz (B20) currently, which is most widespread LTE frequency in my country and this one is only available one in my location. And I was able connect to this network before. Unfortunately I don't know how I can bring it back.
Solved.
My friend share her .xqcn file with me (she has same phone) so I flashed modem file via QPST Flash Tool to my device. Xiaomi started receiving LTE in my location- B20 frequency band, unfortunatelly it was continuously connecting and disconnecting between "no signal" and 4G.
The next step was flash MIUI 10 Global Beta ROM 8.8.9 to my phone via Miflash. LTE seems be stable and fully working now.