i have a droid razr and it was used on pageplus network and i am wanting to sell it, what do i need to do to get it back to verizon settings, the phone is rooted and on stock rom.
vk4559 said:
i have a droid razr and it was used on pageplus network and i am wanting to sell it, what do i need to do to get it back to verizon settings, the phone is rooted and on stock rom.
Click to expand...
Click to collapse
As far as I know.. just reflash it with Verizon's crap..lol
Does it really matter where from? I replied‚ didn't I?
vk4559 said:
i have a droid razr and it was used on pageplus network and i am wanting to sell it, what do i need to do to get it back to verizon settings, the phone is rooted and on stock rom.
Click to expand...
Click to collapse
Use your computer and download RSDLite, make sure you have the motorola drivers installed too. Then download the Verizon firmware from here: http://sbf.droid-developers.org/
Once you have all that set up.
Turn off the phone
Then press the power button, volume up button, and volume down button all at the same time
This will bring up a menu
Scroll down using the down volume key and highlight AP Fastboot
Select AP Fastboot using the volume up key
Plug your phone into the computer using a cable
Open RSDLite
Press the three dots (...) to locate the Verizon Firmware you downloaded
Press Unzip and flash
THIS WILL ERASE EVERYTHING ON THE PHONE
Related
This is my first post on XDA, so hello everyone! lol I think I've graduated from "noob" to eager learner, but this one has me stumped. Any help would be GREATLY appreciated.
I have a Verizon cdma RAZR Maxx, rooted, running Eclipse v1.3 custom ROM, 2.3.6., and cwm/bootstrap. I'm wanting to check out the new ICS ROM, but I can't get back to stock! When I tried recovery it said no files found. I tried RSD lite and it said it failed. I've tried wiping cache and factory reset too and none of that helped. I'm not sure which direction to go now...any ideas?
try using this http://forum.xda-developers.com/showthread.php?t=1486718
Add to original post
I forgot to add that I also tried mattlgroff's utility and it kept saying that the system could not find the correct path...??????
are you sure you are in fastboot mode
fastboot mode
Yes. I powered down holding the power and vol+- buttons, released power, and waited til the black screen w/white letters came up. I vol- twice to AP Fastboot, the vol+ to select. Then plugged in the phone and waited until it said USB connected and started the utility. I selected option one and followed the instructions from there and it wouldn't work.
I have another razr maxx with a shattered screen that I have to send back to the insurance company. It's rooted but still running stock. Can I pull the system files from it and push them to my other razr?
Hello, I am new to this forum.
I will try to explain the best that I can about how I got into this situation.
I was previously running on ICS 4.0.4(don't really know if it is .211 or .214 or something.). I tried to root it using Matt's Droid Razr Utility 1.7. I didn't really know what to do and was stupid enough to follow the video in the help thread(which was for upgrading from GB rather than rooting an ICS). Then I panicked.
I used option 1, followed by option 9, followed by option 3, followed by option 2, and then all four in random orders. Later on, I realized that I had to recover from the .211 file in the sd card after option 1(failure on my part). However, now whenever I try to enter recovery, I get Invalid Flash Mode Boot failure, whereas a normal boot will give me Invalid Flash Mode Flash failure.
I tried to use ADB tools and it didn't work.
Then I tried Utility 1.81. My driver is the same as the one provided, and the cable is the one that came along with the charger and phone.
My phone carrier is Singtel.
Any way out of this? Thanks in advance.
is it possible to enter fastboot ??
if so try to grab an image in development section wich you can place on your phone with RSD lite.
misterx11 said:
is it possible to enter fastboot ??
if so try to grab an image in development section wich you can place on your phone with RSD lite.
Click to expand...
Click to collapse
I can enter fastboot, and only fastboot. Attempting to enter any BP or recovery will result in the failures.
I just downloaded a stock rom for my phone. I'll see how it turns out.
Thank you for your time.
im in a similar situation, my phone is bricked, how do u enter fastboot? and where can i get a rom to use in rsd lite?
rageofshadow said:
I can enter fastboot, and only fastboot. Attempting to enter any BP or recovery will result in the failures.
I just downloaded a stock rom for my phone. I'll see how it turns out.
Thank you for your time.
Click to expand...
Click to collapse
chip0 said:
im in a similar situation, my phone is bricked, how do u enter fastboot? and where can i get a rom to use in rsd lite?
Click to expand...
Click to collapse
Do yall have XT910 or XT912 i.e. GSM or CDMA...
circleofomega said:
Do yall have XT910 or XT912 i.e. GSM or CDMA...
Click to expand...
Click to collapse
Since the thread name is Droid razr i think it is xt912
Go fast boot (power off your phone[if you cant then push and hold vol down+vol up and power button the same time, when you see your display flashed quickly release all buttons and press them again and hold- you should get boot menu and then use vol down to get on AP fastboot and use vol up to select it]).
Then use rsd lite and FXZ files to get your phone running, no need for any kind of wipe after this. Wait until rsd lite says finished.
What fxz files do I use? I've tried like 3 different ones and they always fail
Sent from my DROID RAZR using xda app-developers app
Hi,
I'm new to rooting and modifying and I'm sure I really screwed things up. My main issue is that my Razr is stuck in a bootloop and when I go to use Safestrap to recover it, the utility won't work. I'll try and detail everything I did that led up to this.
Yesterday, I rooted my stock ICS Verizon Razr xt912 using pedrotorresfilho's method. It worked without a hitch. I installed ROM Manager and then Safestrap 2.01. I used Safestrap to install CWM Touch Only Recovery. Part of the directions had me use the SuperSU to set Safestrap to denied after all was said and done. Safestrap created a restore file which I placed in my external sd. After that everything worked like it was supposed to.
Today, I decided to flash a custom ROM, but first I wanted to update to the latest version of Safestrap. I couldn't access it to uninstall the previous version because I had set it to denied. I re-granted its permission. Before I went to uninstall it I decided to go all the way back to stock thinking I probably screwed things up. I never set it back to denied. I rebooted my phone and it went into the startup screen for Safestrap. I hit the menu key, the screen went black as if it was going into the main menu and instead it starts to boot and gets stuck in a bootloop. Every time I hit volume down + power button and reboot the phone it keeps on doing this. I cannot get Safestrap to work so I can recover my phone.
I tried to use the default recovery but that won't work either. Hitting the right combination of buttons only brings me back to the Safestrap menu. I have been looking all over the forums here and elsewhere and nothing is helping. The utilities I have seen won't work for me. I don't care if I have to revert back to factory settings.
I'm sure other people will be more help, but I'll throw something out there. Hold volume down and power until it shuts off then immediately hold both volume and power. It should bout into the bootloader. Select AP fastboot and use mats utility to restore to factory.
Also, don't kill the battery if this doesn't work wake fire me knowable help.
Sent from my DROID RAZR using xda app-developers app
Thanks for the response. I was finally able to get into the bootloader using the instructions you gave me and selected the AP fastboot. Unfortunately, the power button + volume key method wouldn't work and now the battery is dead. I have since plugged it in but now it won't charge and the utility says the battery is too low to run it. Whenever I pull the cable out it gives me the battery symbol with a question mark inside. I'll leave it plugged in over night and hopefully it gives me something.
Moosiah said:
Thanks for the response. I was finally able to get into the bootloader using the instructions you gave me and selected the AP fastboot. Unfortunately, the power button + volume key method wouldn't work and now the battery is dead. I have since plugged it in but now it won't charge and the utility says the battery is too low to run it. Whenever I pull the cable out it gives me the battery symbol with a question mark inside. I'll leave it plugged in over night and hopefully it gives me something.
Click to expand...
Click to collapse
I don't think that's gonna work, you might want to check this out. I think you're going to need it.
http://forum.xda-developers.com/showthread.php?p=20521609
There is also an alternative method, but I couldn't find it.
Sent from my DROID RAZR using xda app-developers app
I saw this method earlier and was hoping I didn't have to go this route. But, it looks like this is my only option short of calling customer service, bs'ing them on why my phone is acting up, and hopefully not get charged full price for a replacement.
Thank you for the help. Next time I'm going to take the time and read up on everything I need to know before I start modifying.
No problem, let me know how it turns out
Sent from my DROID RAZR using xda app-developers app
Update:
I had tried to make my own Motorola Factory Cable but my skills with soldering and such are sub-par so I decided to order a pre-made cable from a Chinese company on Ebay. After a month I finally got the cable today and it works like it should. After going through the steps my Razr boots into AP Fastboot mode. It tells me the battery is okay and is ready for programming. I downloaded the ICS fastboot file and RSD Lite 5.7. When I go through the steps with RSD it loads the files but it won't recognize my device. I repeatedly hit the buttons but nothing shows up. I re-installed it but the same problems persists. If I understood the directions correctly I need the Motorola Device Manager in order to get the USB drivers on a pc (using a friends comp, don't have one of my own atm). I installed it from Motorola's page but when I plug in my Razr nothing pops up. I've tried to find the drivers online but all the links I have found direct me back to the Motorola page. Is there a way to get the drivers without connecting my phone to a computer?
Did I follow the directions right? Is there something I am completely missing?
For a recap. I fubar'd my Razr, it won't charge that is why I needed the "factory cable", battery is okay, but when I connect with either this cable or a normal micro-usb cable the comp won't even see that it is there.
Edit: I was finally able to download the USB drivers from Matt's Razr Utility 1.7 and then RSD was able to recognize my phone. I was able to flash ICS back onto the phone and now I have a fully functioning RAZR. Curious though, I was made to understand that when I flashed the OS that everything would be erased and I would start over. When my phone turned on it brought me back to the state I had it before it bricked. It was still rooted.
Was my photon 2.3.5 which died of electrify sbf install to revive him but then I noticed that when taking a picture to call or listening to music reincia I could not find the solution to this problem. can be used but only restarts.
Flash this give you back stock 2.3.5
http://www.mediafire.com/?hji3s79s8cs14c6
Sent from my MB855 running AT&T using xda app-developers app
correct odungri
excuse my ignorance but how I can install the stock a photon, since I am new to android.
patasolientes said:
excuse my ignorance but how I can install the stock a photon, since I am new to android.
Click to expand...
Click to collapse
download rsd lite, then download the sbf, turn your phone off and then hold the vol down button and press the power button. Next you'll see press the vol button down until you see rsd at the top of the screen then press the vol up button. Plug your phone up to the computer. Open up rsd lite and find the sbf file and click start.
hello i have a motorola xt910 rzr I did the root wanted to install the cyanogen 11 reboot into recovery do the wipe install rom and gapps reboot motorola symbol appears and then black screen (you can see it lit but riamane black) and no restart the ' All I can do is (by pressing the power on and the two volume keys ) to enter the recovery menu selection but if I get a screen with an android and a triangle
I had put the recovery via bootstrap
I know you help?
Can you get into AP fastboot? It's an option you select after getting into the default recovery menu. If you can, then connect it to pc and try flashing a stock JB ROM with RSD Lite. You might need to charge the phone if the battery has run down. You should be able to get it to charge... Just play around.
Let us know.
Generated on a RAZR Maxx (XT910) using XDA's free mobile app.
d.casper.b said:
Can you get into AP fastboot? It's an option you select after getting into the default recovery menu. If you can, then connect it to pc and try flashing a stock JB ROM with RSD Lite. You might need to charge the phone if the battery has run down. You should be able to get it to charge... Just play around.
Let us know.
Generated on a RAZR Maxx (XT910) using XDA's free mobile app.
Click to expand...
Click to collapse
I solved thanks